1 Temat przez olek210 (edytowany przez olek210 2020-05-30 18:09:22)

  • Skąd: Warszawa
  • Zarejestrowany: 2017-04-09
  • Posty: 60

Temat: DWR-966 bootowanie z NAND

Cześć,
próbuje uruchomić OpenWRT na tym routerze. Do tej pory bawiłem się obrazem initramfs, a teraz chciałem wgrać obraz do flash.
Hardware:
CPU: Lantiq GRX390
RAM: 128MB
Flash: 128MB NAND

Nie mam pojęcia do końca pojęcia jak zbootować obraz z uboota. Eksperymetalnie spróbowałem tylko wgrać obraz przez sysupgrade ze zbootowanego obrazu initramfs (tak jak to było dla BT Home Hub 5A). Efekt jest następujący:

root@OpenWrt:/tmp# sysupgrade openwrt-lantiq-xrx300-dlink_dwr-966-squashfs-sysup
grade.bin
Cannot save config while running from ramdisk.
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... rpcd netifd odhcpd uhttpd ntpd dnsmasq ubusd urngd logd
Sending KILL to remaining processes ...
Performing system upgrade...
removing ubiblock0_1
[ 1098.723047] block ubiblock0_1: released
Volume ID 0, size 17 LEBs (2193408 bytes, 2.0 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "kernel", alignment 1
Volume ID 1, size 16 LEBs (2064384 bytes, 1.9 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 78188544
Volume ID 7, size 606 LEBs (78188544 bytes, 74.5 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
umount: can't unmount /: Invalid argument
[ 1100.210442] reboot: Res�
ROM VER: 1.0.0
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-dirty-LANTIQ-v-2.3.08 (Aug 14 2015 - 10:30:43)

CLOCK CPU 600M RAM 300M
16 Bit RAM
DRAM:  128 MiB
NAND:  ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In:    serial
Out:   serial
Err:   serial
Net:   internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
ar10 Switch

Type "run flash_nfs" to mount root filesystem over NFS

part1_err=0,part2_err=0
Hit any key to stop autoboot:  0
argv=1
partnum=1
Creating 1 MTD partitions on "nand0":
0x0000001c0000-0x000007dc0000 : "mtd=4"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            124 MiB
UBI: number of good PEBs:        992
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     8
UBI: available PEBs:             11
UBI: total number of reserved PEBs: 981
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 22/10
Volume kernel found at volume id 0
read 2097152 bytes from volume 0 to 80800000(buf address)
size=2172023,name=MIPS OpenWrt Linux-4.19.123
Bad kernel Checksum
CRC error , changing another booting partition from 1
Erasing redundant Nand...
Erasing at 0x160000 -- 100% complete.
Writing to redundant Nand... done

ROM VER: 1.0.0
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-dirty-LANTIQ-v-2.3.08 (Aug 14 2015 - 10:30:43)

CLOCK CPU 600M RAM 300M
16 Bit RAM
DRAM:  128 MiB
NAND:  ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In:    serial
Out:   serial
Err:   serial
Net:   internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
ar10 Switch

Type "run flash_nfs" to mount root filesystem over NFS

part1_err=1,part2_err=0

Wywala się na nieprawidłowej sumie CRC. Być może coś jest nie tak z partycją UBI, albo czegoś jeszcze brakuje. Ma ktoś pomysł jak rozwiązać ten problem?


partycje na oryginalnym obrazie:

root@home:/# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00100000 00020000 "uboot"
mtd1: 00040000 00020000 "ubootconfigA"
mtd2: 00040000 00020000 "ubootconfigB"
mtd3: 00040000 00020000 "gphyfirmware"
mtd4: 07c00000 00020000 "system_sw"
mtd5: 00100000 00020000 "calibration"
mtd6: 00100000 00020000 "factory"
mtd7: 00040000 00020000 "res"
mtd8: 001b9000 0001f800 "kernel"
mtd9: 00fdf800 0001f800 "rootfs"
mtd10: 0140e800 0001f800 "data_vol"
mtd11: 00217800 0001f800 "kernelb"
mtd12: 0101e800 0001f800 "rootfsb"
mtd13: 0001f800 0001f800 "sysconfig"
mtd14: 00217800 0001f800 "defconfig"

bootlog

ROM VER: 1.0.0
CFG 06
NAND

ROM VER: 1.0.0
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-dirty-LANTIQ-v-2.3.08 (Aug 14 2015 - 10:30:43)

CLOCK CPU 600M RAM 300M
16 Bit RAM
DRAM:  128 MiB
NAND:  ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In:    serial
Out:   serial
Err:   serial
Net:   internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
ar10 Switch

Type "run flash_nfs" to mount root filesystem over NFS

part1_err=0,part2_err=0
Hit any key to stop autoboot:  0
argv=1
partnum=1
Creating 1 MTD partitions on "nand0":
0x0000001c0000-0x000007dc0000 : "mtd=4"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            124 MiB
UBI: number of good PEBs:        992
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     7
UBI: available PEBs:             507
UBI: total number of reserved PEBs: 485
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 20/9
Volume kernel found at volume id 0
read 2097152 bytes from volume 0 to 80800000(buf address)
size=1785792,name=MIPS LTQCPE Linux-3.10.12
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x0000001c0000-0x000007dc0000 : "mtd=4"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            124 MiB
UBI: number of good PEBs:        992
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     7
UBI: available PEBs:             507
UBI: total number of reserved PEBs: 485
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 20/9
Volume rootfs found at volume id 1
read 16629760 bytes from volume 1 to 80800000(buf address)
rootfs CRC = 7E483624


Firmware_version=[DWR-966_v1.0.3CP_r03]

CRC OK, booting...
UBI: mtd1 is detached from ubi0
Creating 1 MTD partitions on "nand0":
0x0000001c0000-0x000007dc0000 : "mtd=4"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            124 MiB
UBI: number of good PEBs:        992
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     7
UBI: available PEBs:             507
UBI: total number of reserved PEBs: 485
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 20/9
Volume kernel found at volume id 0
read 0 bytes from volume 0 to 80800000(buf address)
Read [1806336] bytes
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS LTQCPE Linux-3.10.12
   Created:      2016-04-14   7:57:11 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1785792 Bytes = 1.7 MiB
   Load Address: 80002000
   Entry Point:  8000a970
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.12 (jackson@WNC-JPR233-BM4) (gcc version 4.8.1 20130401 (prerelease) (Linaro GCC 4.8-2013.04) ) #8 Thu Apr 14 15:56:55 CST 2016
[    0.000000] SoC: xRX330 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] adding memory size:267386880 from DT
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 0ff00000 @ 00000000 (usable)
[    1.150000] Switch API: PCE MicroCode loaded !!
[    1.150000] gphy_driver_init: fw_mode:11G-FW, no of phys:4, mode:0
mount: mounting none on /dev/pts failed: No such file or directory
rootdir=/
table='/etc/device_table.txt'
makedevs: line 64: can't create node dev/ram: File exists
makedevs: line 109: can't create node dev/vcc/: File exists
makedevs: line 111: can't create node dev/vc/: File exists
starting pid 611, tty '': '/etc/init.d/rcS S boot'
Switch antenna
The last switch is under INTernal antenna.
starting pid 655, tty '': '/sbin/getty 115200 ttyLTQ0'
System Init...
ECC failed: 0
ECC corrected: 0
Number of bad blocks: 0
Number of bbt blocks: 0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00100000...
cal_wlan0.bin
mac

(none) login: Using current ascii!!
user obj count 2
Module version: Can Not Connect To /tmp/cgi-2-sys!
sed: bad option in substitution expression
Jan  1 00:00:08 udevd[771]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
Jan  1 00:00:08 udevd[772]: specified group 'tty' unknown

Jan  1 00:00:08 udevd[772]: specified group 'dialout' unknown

Jan  1 00:00:08 udevd[772]: specified group 'kmem' unknown

Jan  1 00:00:08 udevd[772]: specified group 'video' unknown

Jan  1 00:00:08 udevd[772]: specified group 'lp' unknown

Jan  1 00:00:08 udevd[772]: specified group 'disk' unknown

Jan  1 00:00:08 udevd[772]: specified group 'floppy' unknown

Jan  1 00:00:08 udevd[772]: specified group 'cdrom' unknown

Jan  1 00:00:08 udevd[772]: specified group 'tape' unknown

insmod: can't insert '/lib/modules/3.10.12/ltqmips_vrx318_e1.ko': Input/output error
Importing configuration...
upfwFlag: false
bootPar:A
curVer:DWR-966_v1.0.3CP_r03

oldVer:0

Firmware Upgrade: false
@@ import table name: FirewallNatConfig
 Polling Interval = 60
 Priority Threshold = 7
 Byte Rate based Management = 1
 Packet Rate based Management = 0
 Poll history = 1
 Maximum delete sessions = 30
 Mode = 0
@@ import table name: VoiceLine
@@ import table name: VoiceLine
@@ import table name: ethWanSetting
@@ import table name: SPI
@@ import table name: UrlFltrConfig
@@ import table name: FirewallDmz
@@ import table name: VoiceProfile
@@ import table name: wifiClient
@@ import table name: QoS
@@ import table name: RmtMgrConfig
@@ import table name: wifiProfile
@@ import table name: wifiProfile
@@ import table name: wifiProfile
@@ import table name: wifiProfile
@@ import table name: system
@@ import table name: VpnL2TPUserAccount
@@ import table name: ResetToDefault
@@ import table name: lteRadio
@@ import table name: SecurityConfig
@@ import table name: wifiSchedules
@@ import table name: tr69Config
@@ import table name: ntpConfig
@@ import table name: ApFwUpgrade
@@ import table name: accessMgmt
@@ import table name: sysLogInfo
@@ import table name: wifiAOCStrigger
@@ import table name: wifiAOCSstatus
@@ import table name: DhcpServerBasic
@@ import table name: RoutingConfig
@@ import table name: wifiRadio
@@ import table name: wifiRadio
@@ import table name: wifiAP
@@ import table name: wifiAP
@@ import table name: wifiAP
@@ import table name: wifiAP
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: Services
@@ import table name: UPNP
@@ import table name: VpnConfig
@@ import table name: MultiLanguage
@@ import table name: MacTable
@@ import table name: MacTable
@@ import table name: MacTable
@@ import table name: MacTable
Loading USB Host mode driver
@@ import table name: MacTable
@@ import table name: MacTable
@@ import table name: ethWanSwitch
@@ import table name: Lan
@@ import table name: wifiWPS
@@ import table name: wifiWPS
@@ import table name: VpnPPTPUserAccount
@@ import table name: SambaSetting
@@ import table name: dlnaConfig
@@ import table name: ethWanStatus
@@ import table name: lteNwStatus
@@ import table name: lteNwStatus
@@ import table name: AuthCfg
@@ import table name: AuthCfg
@@ import table name: PeerToPeer
@@ import table name: DbgSetting
@@ import table name: wifiACLconfig
@@ import table name: lteNwProfile
@@ import table name: lteNwProfile
@@ import table name: FirewallConfig
@@ import table name: lteWanPriority
@@ import table name: ltePinStatus
@@ import table name: ltePinStatus
@@ import table name: SambaAccount
@@ import table name: SambaAccount
@@ import table name: wifiProfilecommit
@@ import table name: RemoteLog
@@ import table name: RemoteLog
@@ import table name: RemoteLog
@@ import table name: users
@@ import table name: VoiceLineSignaling
@@ import table name: VoiceLineSignaling
@@ import table name: crontab
@@ import table name: groups
@@ import table name: groups
@@ import table name: groups
@@ import table name: wifiStatus
@@ import table name: ddns
@@ import table name: VoiceProfileSignaling
@@ import table name: RoamingPDPType
@@ import table name: lteHwInfo
OK
Import DB : DONE
Found USB module connected on PCI(e)
insmod: can't insert '/lib/modules/3.10.12/usb-storage.ko': File exists
insmod lte modules .....
evtDsptchInit-120 :
evtDsptchInit-141 :
[   16.490000] ltq_gphy_firmware_config: fw_mode:11G-FW, no of phys:4,data_ptr:5440000
Network ok
disable PHY...
run script : firewall.sh
firewall init
run script : firewall_ipv6.sh
firewall_ipv6 init
run script : iptables_fw.sh
iptables_fw init
WWAN init with MAL manager ...
BR_MAC_ADDR= E8:CC:18:B8:F4:9D
run script : firewall_rule.sh
wlan_discover: PCI_DEVICES COUNT: 4
wlan_discover: PCI_ATH COUNT: 1
wlan_discover: PCI_LTQ COUNT: 0
wlan_discover: AHB_WLAN_COUNT: 1
wlan_discover: TOTAL WLAN COUNT: 2
wlan_discover: VALID PHY_CNT: 2
run script : filter_ipv6.sh
ipv6 filter init
run script : SessionLimit.sh
SessionLimit init
run script : filter.sh
filter init
run script : upnp_service.sh
upnp_service init
run script : forward.sh
forward init
run script : vpn_method.sh
vpn_method init
run script : urlfilter.sh
urlfilter init
Switch Init done
wlan_discover: highest discovered apIndex is 2
run script : schedule_rule.sh
schedule_rule init
run script : regmag.sh
regmag init
rc.bringup_wlan init
wlan_cmd =init
i=0
Initializing wave
run script : QosInit.sh
run script : dmz.sh
dmz init
sh: 0: unknown operand
net.ipv6.conf.all.disable_ipv6 = 1
IPv6 ENABLE is off
starting webs Daemon...dwatch: process[/usr/local/bin/webs]: 2596
successfully started  webs(pid2596)
Done
net.ipv6.conf.all.disable_ipv6 = 1
addr:192.168.1.1
killall: dnsmasq: no process killed
[um.c]pUserName:admin, pPassword:admin, pGroup:admin
setup accounts...
setup accounts...Enter Admin
.
tar: invalid gzip magic
tar: can't open '/tmp/eeprom.tar.gz': No such file or directory
dwatch: process[udhcpd]: 2747
successfully started  udhcpd(pid2747)
udhcpd (v1.17.1) started
mtlk module loaded in address: 0x86f00000
mtlkroot module loaded in address: 0x85510000
enable PHY...
LTETrig=
cat: can't open '/tmp/wifisetting_11n': No such file or directory
ifconfig: SIOCGIFFLAGS: No such device
rc.bringup_wlan start 0 1
START_VAP=0 , END_VAP=1
Starting Wave interface 0
sh: 2: unknown operand
[   52.730000] [RMNET:HI] rmnet_vnd_ioctl(): Unkown IOCTL 0x00008B01
drvhlpr.sh: drvhlpr terminated with status 4
ALERT #####################################################################################
ALERT ######### mtlk_set_wls_if: MAC of wlan0 is wrong. Must end with 0 or 8 ##########
ALERT ######### Number of supported VAPs may be limited due to this error #################
ALERT #####################################################################################
by pass mtlk_init_hostapd.sh
killing 4159
sh: can't kill pid 4159: No such process
WLANBeacon=100
WLANRTSTh=2346
WLANCh=0
WLANNetMode=bgn
WLANFortyMode=2040
WLANBoningCh=1
WLANTxoffset=0
WLANNetMode_int=23
WLANFortyMode_int=1
cat: can't open '/tmp/wifiDebug': No such file or directory
cant get the LTE bandinfo
WIFI ACL control script
Configuration file: /tmp/hostapd_1.conf
Using interface wlan0 with hwaddr e8:cc:18:b8:f4:9f and ssid "DWR-966_B8F49D"
WLANACLEn_1=0
WLANACLEn_2=0
disable the ACL
rc.bringup_wlan start 1 2
START_VAP=1 , END_VAP=2
Starting Wave interface 1
by pass mtlk_init_hostapd.sh
non boot phase
iptables: Bad rule (does a matching rule exist in that chain?).
interface ath1 does not exist!
interface ath1 does not exist!
udhcpd (v1.17.1) started
udhcpd: can't open '/var/lib/misc/udhcpd_br1.leases': No such file or directory
WIFI ACL control script
WLANACLEn_1=0
WLANACLEn_2=0
disable the ACL
no platform found
rc.bringup_wlan initac
wlan_cmd =initac
i=1
Initializing ath
[   80.230000] +HWT
[   80.230000] -HWT
[   80.230000] HTC Service:0x0300 ep:1 TX flow control disabled
[   80.240000] HTC Service:0x0100 ep:2 TX flow control disabled
[   80.260000] HTC TX lookup failed!
[   80.260000] HTC TX lookup failed!
[   80.270000] HTC TX lookup failed!
[   80.270000] HTC TX lookup failed!
[   80.270000] HTC TX lookup failed!
[   80.280000] HTC TX lookup failed!
[   80.280000] HTC TX lookup failed!
[   80.280000] HTC TX lookup failed!
[   80.290000] HTC TX lookup failed!
[   80.290000] HTC TX lookup failed!
[   80.290000] HTC TX lookup failed!
[   80.290000] HTC TX lookup failed!
[   80.300000] HTC TX lookup failed!
[   80.300000] HTC TX lookup failed!
[   80.300000] HTC TX lookup failed!
[   80.310000] HTC TX lookup failed!
[   80.310000] HTC TX lookup failed!
[   80.310000] HTC TX lookup failed!
[   80.320000] HTC TX lookup failed!
[   80.320000] HTC TX lookup failed!
[   80.320000] HTC TX lookup failed!
[   80.330000] HTC TX lookup failed!
[   80.330000] HTC TX lookup failed!
[   80.330000] HTC TX lookup failed!
[   80.340000] HTC TX lookup failed!
[   80.340000] HTC TX lookup failed!
[   80.340000] HTC TX lookup failed!
[   80.350000] HTC TX lookup failed!
[   80.350000] HTC TX lookup failed!
[   80.350000] HTC TX lookup failed!
[   80.360000] HTC TX lookup failed!
[   80.360000] HTC TX lookup failed!
[   80.360000] HTC TX lookup failed!
[   80.370000] HTC TX lookup failed!
[   80.370000] HTC TX lookup failed!
[   80.370000] HTC TX lookup failed!
[   80.380000] HTC TX lookup failed!
[   80.380000] HTC TX lookup failed!
[   80.380000] HTC TX lookup failed!
[   80.390000] HTC TX lookup failed!
[   80.390000] HTC TX lookup failed!
[   80.390000] HTC TX lookup failed!
[   80.400000] HTC TX lookup failed!
[   80.400000] HTC TX lookup failed!
[   80.400000] HTC TX lookup failed!
[   80.410000] HTC TX lookup failed!
[   80.410000] HTC TX lookup failed!
[   80.410000] HTC TX lookup failed!
[   80.420000] HTC TX lookup failed!
[   80.420000] HTC TX lookup failed!
[   80.420000] HTC TX lookup failed!
[   80.430000] HTC TX lookup failed!
[   80.430000] HTC TX lookup failed!
[   80.430000] HTC TX lookup failed!
[   80.440000] HTC TX lookup failed!
[   80.440000] HTC TX lookup failed!
[   80.440000] HTC TX lookup failed!
[   80.450000] HTC TX lookup failed!
[   80.450000] HTC TX lookup failed!
[   80.450000] HTC TX lookup failed!
[   80.460000] HTC TX lookup failed!
[   80.460000] HTC TX lookup failed!
[   80.460000] HTC TX lookup failed!
rc.bringup_wlan start 2 4
START_VAP=2 , END_VAP=4
Starting QCA interface
ath_wlan_ap_start 2
[   81.840000] [RMNET:HI] rmnet_vnd_ioctl(): Unkown IOCTL 0x00008B01
Create ath0 interface for device wifi0
[   81.940000] VAP device ath0 created
ath0
Radio is up
wifi interface wifi0 is up
ifconfig: SIOCGIFFLAGS: No such device
/etc/rc.d/ath_wlan_ap_start: line 1: [1: not found
Interface doesn't accept private ioctl...
AMPDU (8BE0): Operation not permitted
Interface doesn't accept private ioctl...
AMPDUFrames (8BE0): Operation not permitted
Interface doesn't accept private ioctl...
AMPDULim (8BE0): Operation not permitted
Error for wireless request "Set Frequency" (8B04) :
    SET failed on device ath0 ; Invalid argument.
/etc/rc.d/ath_wlan_ap_start: line 1: [1: not found
Making Topology File . . .
Starting QCA interface
ath_wlan_ap_start 3
[   86.370000] [RMNET:HI] rmnet_vnd_ioctl(): Unkown IOCTL 0x00008B01
Create ath1 interface for device wifi0
[   86.450000] VAP device ath1 created
ath1
Radio is up
wifi interface wifi0 is up
/etc/rc.d/ath_wlan_ap_start: line 1: [1: not found
Interface doesn't accept private ioctl...
AMPDU (8BE0): Operation not permitted
Interface doesn't accept private ioctl...
AMPDUFrames (8BE0): Operation not permitted
Interface doesn't accept private ioctl...
AMPDULim (8BE0): Operation not permitted
Error for wireless request "Set Frequency" (8B04) :
    SET failed on device ath1 ; Invalid argument.
/etc/rc.d/ath_wlan_ap_start: line 1: [1: not found
Making Topology File . . .
ath0      Link encap:Ethernet  HWaddr E8:CC:18:B8:F4:9E
cat: can't open '/tmp/wifisetting_11ac': No such file or directory
killing 5251
sh: can't kill pid 5251: No such process
WLANBeacon=100
WLANRTSTh=2346
WLANCh=0
WLANNetMode=ac
WLANFortyMode=80
WLANBoningCh=1
WLANNetMode_s=11AC
WLANFortyMode_s=VHT80
CHMODE=11ACVHT80
QCA9880 warming up 1 sec
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
QCA9880 warm up
non boot phase
Configuration file: /tmp/hostapd_ac.conf
ath0: Could not connect to kernel driver
Using interface ath0 with hwaddr e8:cc:18:b8:f4:9e and ssid 'DWR-966_5GHz_B8F49D'
WIFI ACL control script
WLANACLEn_1=0
WLANACLEn_2=0
disable the ACL
RUN led_config.sh
killall: ripd: no process killed
killall: syslogd: no process killed
killall: syslog-ng: no process killed
Power LED : delay_on=, delay_off=0, brightness=1
killall: send_radiosyslog.sh: no process killed
killall: send_voipsyslog.sh: no process killed
sh: can't kill pid 5423: No such process
--------------- EMI CMD START ---------------
writing 0x8000000f into address 0x1f2030c8
--------------- Disable Auto-polling ---------------
--------------- Disable port 0 GPHY CLKOUT ---------------
write dev=0x0, reg=0xd, data=0x1f
write dev=0x0, reg=0xe, data=0xea9
write dev=0x0, reg=0xd, data=0x401f
write dev=0x0, reg=0xe, data=0x15
--------------- RGMII slew rate control enable ---------------
write dev=0x0, reg=0xd, data=0x1f
write dev=0x0, reg=0xe, data=0xea8
write dev=0x0, reg=0xd, data=0x401f
write dev=0x0, reg=0xe, data=0x85
--------------- Enable Auto-polling ---------------
--------------- Restart auto-negotiation ---------------
--------------- EMI CMD END ---------------
--------------- Change Ethernet Port output voltage START ---------------
write dev=0x0, reg=0x13, data=0x501
write dev=0x2, reg=0x13, data=0x501
write dev=0x4, reg=0x13, data=0x501
write dev=0x1, reg=0x13, data=0x501
--------------- Change Ethernet Port output voltage END ---------------
event handler already exist.
Terminated
Not start VoIP Services...Done
TR69 is Disabled
killall: inadyn: no process killed
run script : upnp_service.sh
killall: miniupnpd: no process killed
UPNP Service on
BOOTLoader:U-Boot-2010.06-dirty-LANTIQ-v-2.3.08
CPU:P02003
Kernel:3.10.12
Software:DWR-966_v1.0.3CP_r03-1556-14Apr16
Branch:P02003-UGW-6.1
Tool Chain:4.8-linaro/0.9.33.2
PPA SubSystem version info:v3.0.0-0
PPA ppacmd utility tool info:2.9.0
PPE HAL driver info:128.4.3.1.0.0.2
Switch API Version: 2.0.1
Wave wlan version: 03.04.02.40_05_UGW_6.1
Wave wlan driver version: 03.04.02.00.25.c9c85872fd07
Wave wlan MAC FW version: FW_3.4.2_based_on_3.4.2.40_for_UGW_r3625
Wave300 wlan PHY version: 1668
AR10 wlan PHY version: 1796
Wave wlan scripts version:
Starting the cron deamon...crond started
/etc/rc.common: line 92: ./mnt/data/dbg_script.sh: not found

bootlog z openwrt:

ROM VER: 1.0.0  
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-dirty-LANTIQ-v-2.3.08 (Aug 14 2015 - 10:30:43)

CLOCK CPU 600M RAM 300M
16 Bit RAM
DRAM:  128 MiB  
NAND:  ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In:    serial   
Out:   serial   
Err:   serial   
Net:   internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
ar10 Switch

Type "run flash_nfs" to mount root filesystem over NFS

part1_err=0,part2_err=0
Hit any key to stop autoboot:  0
GRX330 # setenv loadaddr 0x84000000
GRX330 # run net_ram
Using ar10 Switch device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'uImage'.
Load address: 0x84000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ####################
done
Bytes transferred = 4109737 (3eb5a9 hex)
## Booting kernel from Legacy Image at 84000000 ...
   Image Name:   MIPS OpenWrt Linux-4.19.123
   Created:      2020-05-30  13:40:47 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4109673 Bytes = 3.9 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.19.123 (aleksander@LAPTOP-OLEK) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13400-d182e08d92)) #0 SMP Sat May 30 13:40:47 2020
[    0.000000] SoC: xRX330 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is D-Link DWR-966
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x98/0x4dc with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu s26256 r8192 d22896 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyLTQ0,115200
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0007fff0
[    0.000000] Readback ErrCtl register=0007fff0
[    0.000000] Memory: 119672K/131072K available (5091K kernel code, 201K rwdata, 1292K rodata, 3128K init, 227K bss, 11400K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 600MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[    0.007891] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.045938] pid_max: default: 32768 minimum: 301
[    0.050851] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.057350] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.067410] rcu: Hierarchical SRCU implementation.
[    0.073260] smp: Bringing up secondary CPUs ...
[    0.078695] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.078710] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.078845] CPU1 revision is: 00019556 (MIPS 34Kc)
[    0.105870] Synchronize counters for CPU 1: done.
[    0.130196] smp: Brought up 1 node, 2 CPUs
[    0.138401] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.148033] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.154489] pinctrl core: initialized pinctrl subsystem
[    0.161390] NET: Registered protocol family 16
[    0.183192] pinctrl-xway 1e100b10.pinmux: Init done
[    0.189323] dma-xway 1e104100.dma: Init done - hw rev: 8, ports: 5, channels: 24
[    0.223147] gpio-stp-xway 1e100bb0.stp: Init done
[    0.229193] usbcore: registered new interface driver usbfs
[    0.234761] usbcore: registered new interface driver hub
[    0.240115] usbcore: registered new device driver usb
[    0.247900] clocksource: Switched to clocksource MIPS
[    0.254483] NET: Registered protocol family 2
[    0.260285] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.267895] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.274880] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.281308] TCP: Hash tables configured (established 1024 bind 1024)
[    0.287881] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.293656] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.300277] NET: Registered protocol family 1
[    0.490973] random: fast init done
[    3.860576] gptu: totally 6 16-bit timers/counters
[    3.865414] gptu: misc_register on minor 63
[    3.869576] gptu: succeeded to request irq 126
[    3.874055] gptu: succeeded to request irq 127
[    3.878583] gptu: succeeded to request irq 128
[    3.883111] gptu: succeeded to request irq 129
[    3.887608] gptu: succeeded to request irq 130
[    3.892124] gptu: succeeded to request irq 131
[    3.896782] No VPEs reserved for AP/SP, not initialize VPE loader
[    3.896782] Pass maxvpes=<n> argument as kernel argument
[    3.908149] No TCs reserved for AP/SP, not initializing RTLX.
[    3.908149] Pass maxtcs=<n> argument as kernel argument
[    3.920770] Crashlog allocated RAM at address 0x3f00000
[    3.926301] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    3.946423] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.952185] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    3.970800] io scheduler noop registered
[    3.974808] io scheduler deadline registered (default)
[    3.982465] xway-rcu-gphy 1f203000.rcu:gphy@264: Failed to lookup gate clock
[    3.989516] xway-rcu-gphy: probe of 1f203000.rcu:gphy@264 failed with error -2
[    3.998306] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    4.007214] console [ttyLTQ0] enabled
[    4.007214] console [ttyLTQ0] enabled
[    4.014516] bootconsole [early0] disabled
[    4.014516] bootconsole [early0] disabled
[    4.026147] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[    4.031168] nand: AMD/Spansion S34ML01G1
[    4.034916] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    4.042476] Scanning device for bad blocks
[    4.114055] 8 fixed-partitions partitions found on MTD device 14000000.nand
[    4.119568] Creating 8 MTD partitions on "14000000.nand":
[    4.124920] 0x000000000000-0x000000100000 : "uboot"
[    4.131272] 0x000000100000-0x000000140000 : "ubootconfigA"
[    4.136825] 0x000000140000-0x000000180000 : "ubootconfigB"
[    4.142405] 0x000000180000-0x0000001c0000 : "gphyfirmware"
[    4.148099] 0x0000001c0000-0x000007dc0000 : "ubi"
[    4.154129] 0x000007dc0000-0x000007ec0000 : "calibration"
[    4.159703] 0x000007ec0000-0x000007fc0000 : "factory"
[    4.164886] 0x000007fc0000-0x000008000000 : "res"
[    4.170853] libphy: Fixed MDIO Bus: probed
[    4.176665] wdt 1f8803f0.watchdog: Init done
[    4.187343] NET: Registered protocol family 10
[    4.193591] Segment Routing with IPv6
[    4.196001] NET: Registered protocol family 17
[    4.200382] 8021q: 802.1Q VLAN Support v1.8
[    4.315256] libphy: lantiq,xrx200-mdio: probed
[    4.407436] Intel XWAY PHY11G (xRX v1.2 integrated) 0:01: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:01, irq=POLL)
[    4.421004] Intel XWAY PHY11G (xRX v1.2 integrated) 0:02: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:02, irq=POLL)
[    4.434645] Intel XWAY PHY11G (xRX v1.2 integrated) 0:03: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:03, irq=POLL)
[    4.448286] Intel XWAY PHY11G (xRX v1.2 integrated) 0:04: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:04, irq=POLL)
[    4.463226] UBI: auto-attach mtd4
[    4.465094] ubi0: attaching mtd4
[    4.602655] ubi0: scanning is finished
[    4.633808] ubi0: attached mtd4 (name "ubi", size 124 MiB)
[    4.637913] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    4.644693] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    4.651337] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[    4.658059] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[    4.664027] ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128
[    4.671199] ubi0: max/mean erase counter: 22/9, WL threshold: 4096, image sequence number: 0
[    4.679579] ubi0: available PEBs: 496, total reserved PEBs: 496, PEBs reserved for bad PEB handling: 20
[    4.688962] ubi0: background thread "ubi_bgt0d" started, PID 450
[    4.692396] block ubiblock0_1: created from ubi0:1(rootfs)
[    4.700326] ubiblock: device ubiblock0_1 (rootfs) set to be root fil[    4.716918] Freeing unused kernel memory: 3128K
[    4.720032] This architecture does not have kernel memory protection.
[    4.726391] Run /init as init process
[    4.749993] init: Console is alive
[    4.752319] init: - watchdog -
[    4.776215] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.787516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.799970] SCSI subsystem initialized
[    4.807099] ehci-platform: EHCI generic platform driver
[    4.817347] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
[    4.824353] dwc2 1e101000.usb: Linked as a consumer to regulator.0
[    4.830301] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
[    4.941437] dwc2 1e101000.usb: DWC OTG Controller
[    4.944798] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
[    4.951776] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
[    4.958221] hub 1-0:1.0: USB hub found
[    4.960833] hub 1-0:1.0: 1 port detected
[    4.965830] dwc2 1e106000.usb: 1e106000.usb supply vusb_d not found, using dummy regulator
[    4.972964] dwc2 1e106000.usb: Linked as a consumer to regulator.0
[    4.978986] dwc2 1e106000.usb: 1e106000.usb supply vusb_a not found, using dummy regulator
[    5.089247] dwc2 1e106000.usb: DWC OTG Controller
[    5.092589] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2
[    5.099567] dwc2 1e106000.usb: irq 91, io mem 0x1e106000
[    5.106004] hub 2-0:1.0: USB hub found
[    5.108659] hub 2-0:1.0: 1 port detected
[    5.117539] usbcore: registered new interface driver usb-storage
[    5.122403] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.132904] init: - preinit -
[    5.313955] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.335358] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.375591] lantiq,xrx200-net 1e108000.eth eth0: port 1 got link
[    8.380211] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    9.494409] procd: - early -
[    9.496142] procd: - watchdog -
[   10.115971] procd: - watchdog -
[   10.118171] procd: - ubus -
[   10.128395] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.170546] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.176035] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.183675] procd: - init -
Please press Enter to activate this console.
[   10.423117] lantiq,xrx200-net 1e108000.eth eth0: port 1 lost link
[   10.630847] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.655773] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[   10.739332] xt_time: kernel timezone is -0000
[   10.773743] PPP generic driver version 2.4.2
[   10.780828] NET: Registered protocol family 24
[   10.808201] kmodloader: done loading kernel modules from /etc/modules.d/*
[   11.021803] urngd: v1.0.2 started.
[   11.221157] random: crng init done
[   11.223147] random: 6 urandom warning(s) missed due to ratelimiting
[   23.101430] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.123812] br-lan: port 1(eth0.1) entered blocking state
[   23.127876] br-lan: port 1(eth0.1) entered disabled state
[   23.133826] device eth0.1 entered promiscuous mode
[   23.137941] device eth0 entered promiscuous mode
[   23.165468] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   28.215590] lantiq,xrx200-net 1e108000.eth eth0: port 1 got link
[   28.220213] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   28.228115] br-lan: port 1(eth0.1) entered blocking state
[   28.232108] br-lan: port 1(eth0.1) entered forwarding state
[   28.239877] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r13401-1d6aff7d75
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------

USB i switch działa więc mogę wrzucić na niego dowolny obraz. Zrobiłem sobie też kopię wszystkich partycji i jak coś pójdzie nie tak przywrócenie oryginalnego softu nie jest problemem. smile

Kod który testuję jest na Githubie. Wszelkie uwagi milie widziane smile

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,913

Odp: DWR-966 bootowanie z NAND

Sprawdź czy gdzieś (uboot, jakieś payload w obrazie) nie ma dodatkowej sumy kontrolnej wczytywanego obrazu

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez olek210 (edytowany przez olek210 2020-05-30 19:16:13)

  • Skąd: Warszawa
  • Zarejestrowany: 2017-04-09
  • Posty: 60

Odp: DWR-966 bootowanie z NAND

Faktycznie u-boot w zmiennych ma zaszyte CRC:

f_rootfs_datalen=FDC000
f_rootfs_crc=7E483624
f_kernel_datalen=1B4000
f_kernel_crc=4925A607

Niby najprostsza opcja a człowiek czasem dostaje zaćmienia umysłu.

Po wpisaniu komendy OpenWRT bootuje z flash:

GRX330 # run bootcmd

1. Wygląda na to, że to na etapie u-boota jest sprawdzane CRC. Tylko czy w takim razie u-boot właśnie nie wywołuje tylko bootcmd domyślnie na starcie?

2. ewentualnie to być może to jest problemem:

read 2097152 bytes from volume 0 to 80800000(buf address)
size=2172023,name=MIPS OpenWrt Linux-4.19.123
Bad kernel Checksum

u-boot ładuje do RAM tylko 2MB, a kernel jest większy i dlatego CRC jest złe. Tylko czy tak samo nie powinno się dziać jak ręcznie wywołuję bootcmd?

Zmienne uboota:

GRX330 # printenv
bootcmd=run flash_flash
bootdelay=1
baudrate=115200
preboot=echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo
bootfile="uImage"
mem=114M
phym=128M
wlanm=119M
part2_err=0
dark_led=mw.l  0xbe100bb8 0xFFE483
green_led=mw.l  0xbe100bb8 0x090402
red_led=mw.l  0xbe100bb8 0xF6E081
all_led=mw.l  0xbe100bb8 0x001010
f_kernelb_crc=0
f_kernelb_datalen=0
f_rootfsb_crc=0
f_rootfsb_datalen=0
part2_version=0
data_2m=0x280000
data_16m=0x1000000
switch2parta=setenv kernelname kernel;setenv rootfsname rootfs;saveenv;reset
switch2partb=setenv kernelname kernelb;setenv rootfsname rootfsb;saveenv;reset
netdev=eth0
console=ttyLTQ0
tftppath=
loadaddr=0x80800000
rootpath=/mnt/full_fs
rootfsmtd=/dev/mtdblock3
nfsargs= setenv bootargs ubi.mtd=system_sw root=/dev/nfs rw nfsroot=$(serverip):$(rootpath)
ramargs=setenv bootargs root=/dev/ram rw
addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):on
addmisc=setenv bootargs $(bootargs) console=$(console),$(baudrate) ethaddr=$(ethaddr) mem=$(mem) wlanm=$(wlanm) panic=1 $(mtdparts) vpe1_load_addr=0x87f00000 vpe1_mem=1M init=/etc/preinit active_bank=$(active_bank) update_chk=$(update_chk) ethwan=$(ethwan) ubootver=$(ver)
flash_nfs=run nfsargs addip addmisc;bootm $(kernel_addr)
net_nfs=tftp $(loadaddr) $(tftppath)$(bootfile);run nfsargs addip addmisc;bootm
net_flash=tftp $(loadaddr) $(tftppath)$(bootfile); run flashargs addip addmisc; bootm
net_ram=tftp $(loadaddr) $(tftppath)$(bootfile); run ramargs addip addmisc; bootm
u-boot=u-boot.ltq
rootfs=rootfs.img
firmware=firmware.img
fullimage=fullimage.img
totalimage=totalimage.img
load=tftp $(loadaddr) $(u-boot)
update=protect off 1:0-2;era 1:0-2;cp.b $(loadaddr) B0000000 $(filesize)
flashargs=setenv bootargs ubi.mtd=system_sw rootfsname=$(rootfsname) ro rootfstype=squashfs quiet
flash_flash=ubi part system_sw;ubi read $(loadaddr) $(kernelname) $(f_kernel_size);run flashargs addip addmisc;bootm $(loadaddr)
update_nandboot=tftp $(loadaddr) $(tftppath)u-boot-nand.bin;nand erase 0 17FFFF;nand erase 1C0000 7bfffff;nand write.partial $(loadaddr) 0 $(filesize)
ubi_init=nand erase 0x1C0000 0x7C00000;ubi part system_sw;ubi create kernel $(data_2m) dynamic 0;ubi create rootfs $(data_16m) dynamic 1;ubi create kernelb $(data_2m) dynamic 3;ubi create rootfsb $(data_16m) dynamic 4
update_uboot=tftp $(loadaddr) $(tftppath)$(u-boot); nand write.partial $(loadaddr) 0x4000 $(filesize);reset
update_kernel=ubi part system_sw;ubi remove kernel;ubi create kernel 0x200000 dynamic 0;tftpboot $(loadaddr) $(tftppath)$(bootfile);ubi write $(loadaddr) $(kernelname) $(filesize)
update_kernelb=ubi part system_sw;ubi remove kernelb;ubi create kernelb 0x200000 dynamic 3;tftpboot $(loadaddr) $(tftppath)$(bootfile);ubi write $(loadaddr) kernelb $(filesize)
update_bootloader=update_uboot
update_rootfs=ubi part system_sw;ubi remove rootfs;ubi create rootfs 0x1000000 dynamic 1;tftpboot $(loadaddr) $(tftppath)$(rootfs);ubi write 0x80800040 $(rootfsname) $(filesize)
update_rootfsb=ubi part system_sw;ubi remove rootfsb;ubi create rootfsb 0x1000000 dynamic 4;tftpboot $(loadaddr) $(tftppath)$(rootfs);ubi write 0x80800040 rootfsb $(filesize)
update_fullimage=setenv kernel_vol kernel;setenv rootfs_vol rootfs;setenv kernel_id 0;setenv rootfs_id 1;ubi part system_sw;tftpboot $(loadaddr) $(tftppath)$(fullimage);upgrade $(loadaddr) $(filesize) 1;setenv rootfsname rootfs;setenv kernelname kernel;setenv part1_err 0;saveenv
update_fullimageb=setenv kernel_vol kernelb;setenv rootfs_vol rootfsb;setenv kernelb_id 3;setenv rootfsb_id 4;ubi part system_sw;tftpboot $(loadaddr) $(tftppath)$(fullimage);upgrade $(loadaddr) $(filesize) 2;setenv rootfsname rootfsb;setenv kernelname kernelb;setenv part2_err 0;saveenv
update_totalimage=run ubi_init;tftpboot $(loadaddr) $(tftppath)$(totalimage);upgrade $(loadaddr) $(filesize)
update_gphyfirmware=tftpboot $(loadaddr) $(tftppath)gphy_firmware.img;nand write.partial $(loadaddr) $(gphy_fw_addr) $(filesize);re
gphy_fw_addr=0x180000
reset_uboot_config=nand erase $(f_ubootconfig_addr) $(f_ubootconfig_range);nand erase $(f_red_ubootconfig_addr) $(f_ubootconfig_range);
reset_ddr_config=nand write.partial 80400000 $(f_ddrconfig_addr) $(f_ddrconfig_size)
reset_sysconfig=run ubi_init;ubi remove sysconfig;ubi remove sysconfigA;ubi remove sysconfigB
mtdparts=mtdparts=ifx_nand:1024k(uboot),256k(ubootconfigA),256k(ubootconfigB),256k(gphyfirmware),124m(system_sw),1m(calibration),1m(factory),-(res)
part0_begin=0x00000000
part1_begin=0x00040000
part2_begin=0x002C0000
part3_begin=0x07000000
part4_begin=0x07040000
part5_begin=0x07080000
total_part=6
flash_end=0x07FFFFFF
data_block0=uboot
data_block1=kernel
data_block2=rootfs
data_block3=sysconfig
data_block4=ubootconfig
data_block5=dectconfig
total_db=6
f_uboot_addr=0x00000000
f_uboot_size=0x40000
f_ubootconfig_addr=0x100000
f_ubootconfig_size=0x4000
f_ubootconfig_end=0x07040FFF
f_ubootconfig_range=0x40000
f_red_ubootconfig_addr=0x140000
f_gphy_firmware_addr=IFX_CFG_FLASH_GPHY_FIRMWARE_IMAGE_START_ADDR
f_gphy_firmware_size=IFX_CFG_FLASH_GPHY_FIRMWARE_IMAGE_SIZE
f_gphy_firmware_end=IFX_CFG_FLASH_GPHY_FIRMWARE_IMAGE_END_ADDR
f_kernel_addr=0x00040000
f_kernel_size=0
f_kernel_end=IFX_CFG_FLASH_KERNEL_IMAGE_END_ADDR
f_rootfs_addr=0x002C0000
f_rootfs_size=0
f_rootfs_end=IFX_CFG_FLASH_ROOTFS_IMAGE_END_ADDR
f_fwdiag_addr=IFX_CFG_FLASH_FIRMWARE_DIAG_START_ADDR
f_fwdiag_size=IFX_CFG_FLASH_FIRMWARE_DIAG_SIZE
f_sysconfig_addr=0x07000000
f_sysconfig_size=0x10000
f_dectconfig_addr=0x07080000
f_dectconfig_size=0x400
f_wlanconfig_addr= IFX_CFG_FLASH_WLAN_CFG_START_ADDR
f_wlanconfig_size=IFX_CFG_FLASH_WLAN_CFG_SIZE
f_ddrconfig_addr=0x00003fe0
f_ddrconfig_size=32
f_ddrconfig_end=0x00003fff
ethact=ar10 Switch
mtdids=nand0=ifx_nand
kernel_vol=kernel
rootfs_vol=rootfs
kernel_id=0
rootfs_id=1
filesize=1190088
fileaddr=80800000
ipaddr=192.168.1.1
serverip=192.168.1.100
f_rootfs_datalen=FDC000
f_rootfs_crc=7E483624
f_kernel_datalen=1B4000
f_kernel_crc=4925A607
part1_version=DWR-966_v1.0.3CP_r03
ethaddr=E8:CC:18:B8:F4:9D
partition=nand0,0
mtddevnum=0
mtddevname=uboot
part1_err=1
kernelname=kernelb
rootfsname=rootfsb
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot-2010.06-dirty-LANTIQ-v-2.3.08

Environment size: 6242/16379 bytes

Cały bootlog:

ROM VER: 1.0.0
CFG 06
NAND

ROM VER: 1.0.0
CFG 06
NAND

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa7ffffff
DDR check ok... start booting...



U-Boot 2010.06-dirty-LANTIQ-v-2.3.08 (Aug 14 2015 - 10:30:43)

CLOCK CPU 600M RAM 300M
16 Bit RAM
DRAM:  128 MiB
NAND:  ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
128 MiB
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
In:    serial
Out:   serial
Err:   serial
Net:   internal phy using 25Mhz clock
Internal phy firmware version: 0x8434
ar10 Switch

Type "run flash_nfs" to mount root filesystem over NFS

part1_err=3,part2_err=3
Both partition firmware are CRC error, stop booting..
Hit any key to stop autoboot:  0
GRX330 #
GRX330 #
GRX330 # run bootcmd
Creating 1 MTD partitions on "nand0":
0x0000001c0000-0x000007dc0000 : "mtd=4"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    129024 bytes
UBI: smallest flash I/O unit:    2048
UBI: sub-page size:              512
UBI: VID header offset:          512 (aligned 512)
UBI: data offset:                2048
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "mtd=4"
UBI: MTD device size:            124 MiB
UBI: number of good PEBs:        992
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     8
UBI: available PEBs:             11
UBI: total number of reserved PEBs: 981
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 22/10
Volume kernel found at volume id 0
read 0 bytes from volume 0 to 80800000(buf address)
Read [2193408] bytes
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-4.19.123
   Created:      2020-05-30  13:40:47 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2172023 Bytes = 2.1 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.19.123 (aleksander@LAPTOP-OLEK) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13400-d182e08d92)) #0 SMP Sat May 30 13:40:47 2020
[    0.000000] SoC: xRX330 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is D-Link DWR-966
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x98/0x4dc with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu s26256 r8192 d22896 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480
[    0.000000] Kernel command line: console=ttyLTQ0,115200
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0007fff0
[    0.000000] Readback ErrCtl register=0007fff0
[    0.000000] Memory: 121528K/131072K available (5091K kernel code, 201K rwdata, 1292K rodata, 1272K init, 227K bss, 9544K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 600MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000009] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[    0.007892] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
[    0.045939] pid_max: default: 32768 minimum: 301
[    0.050851] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.057349] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.067408] rcu: Hierarchical SRCU implementation.
[    0.073262] smp: Bringing up secondary CPUs ...
[    0.078693] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.078708] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.078842] CPU1 revision is: 00019556 (MIPS 34Kc)
[    0.105870] Synchronize counters for CPU 1: done.
[    0.130196] smp: Brought up 1 node, 2 CPUs
[    0.138402] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.148033] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.154493] pinctrl core: initialized pinctrl subsystem
[    0.161406] NET: Registered protocol family 16
[    0.183193] pinctrl-xway 1e100b10.pinmux: Init done
[    0.189331] dma-xway 1e104100.dma: Init done - hw rev: 8, ports: 5, channels: 24
[    0.223051] gpio-stp-xway 1e100bb0.stp: Init done
[    0.229328] usbcore: registered new interface driver usbfs
[    0.234919] usbcore: registered new interface driver hub
[    0.240287] usbcore: registered new device driver usb
[    0.248010] clocksource: Switched to clocksource MIPS
[    0.255435] NET: Registered protocol family 2
[    0.260710] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[    0.268304] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.275314] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.281741] TCP: Hash tables configured (established 1024 bind 1024)
[    0.288315] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.294111] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.300703] NET: Registered protocol family 1
[    0.305578] gptu: totally 6 16-bit timers/counters
[    0.310493] gptu: misc_register on minor 63
[    0.314634] gptu: succeeded to request irq 126
[    0.319157] gptu: succeeded to request irq 127
[    0.323630] gptu: succeeded to request irq 128
[    0.328140] gptu: succeeded to request irq 129
[    0.332660] gptu: succeeded to request irq 130
[    0.337156] gptu: succeeded to request irq 131
[    0.341831] No VPEs reserved for AP/SP, not initialize VPE loader
[    0.341831] Pass maxvpes=<n> argument as kernel argument
[    0.353189] No TCs reserved for AP/SP, not initializing RTLX.
[    0.353189] Pass maxtcs=<n> argument as kernel argument
[    0.365983] Crashlog allocated RAM at address 0x3f00000
[    0.371550] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[    0.387127] random: fast init done
[    0.393917] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.399688] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.418547] io scheduler noop registered
[    0.422391] io scheduler deadline registered (default)
[    0.429812] xway-rcu-gphy 1f203000.rcu:gphy@264: Failed to lookup gate clock
[    0.436868] xway-rcu-gphy: probe of 1f203000.rcu:gphy@264 failed with error -2
[    0.445610] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.454512] console [ttyLTQ0] enabled
[    0.454512] console [ttyLTQ0] enabled
[    0.461796] bootconsole [early0] disabled
[    0.461796] bootconsole [early0] disabled
[    0.473546] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[    0.478423] nand: AMD/Spansion S34ML01G1
[    0.482304] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.489949] Scanning device for bad blocks
[    0.561382] 8 fixed-partitions partitions found on MTD device 14000000.nand
[    0.566917] Creating 8 MTD partitions on "14000000.nand":
[    0.572263] 0x000000000000-0x000000100000 : "uboot"
[    0.578760] 0x000000100000-0x000000140000 : "ubootconfigA"
[    0.584409] 0x000000140000-0x000000180000 : "ubootconfigB"
[    0.589979] 0x000000180000-0x0000001c0000 : "gphyfirmware"
[    0.595661] 0x0000001c0000-0x000007dc0000 : "ubi"
[    0.601702] 0x000007dc0000-0x000007ec0000 : "calibration"
[    0.607278] 0x000007ec0000-0x000007fc0000 : "factory"
[    0.612516] 0x000007fc0000-0x000008000000 : "res"
[    0.618520] libphy: Fixed MDIO Bus: probed
[    0.624387] wdt 1f8803f0.watchdog: Init done
[    0.634950] NET: Registered protocol family 10
[    0.641262] Segment Routing with IPv6
[    0.643677] NET: Registered protocol family 17
[    0.648022] 8021q: 802.1Q VLAN Support v1.8
[    0.762100] libphy: lantiq,xrx200-mdio: probed
[    0.770828] Intel XWAY PHY11G (xRX v1.2 integrated) 0:01: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:01, irq=POLL)
[    0.784467] Intel XWAY PHY11G (xRX v1.2 integrated) 0:02: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:02, irq=POLL)
[    0.798034] Intel XWAY PHY11G (xRX v1.2 integrated) 0:03: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:03, irq=POLL)
[    0.811695] Intel XWAY PHY11G (xRX v1.2 integrated) 0:04: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:04, irq=POLL)
[    0.826522] UBI: auto-attach mtd4
[    0.828494] ubi0: attaching mtd4
[    0.965920] ubi0: scanning is finished
[    0.998393] ubi0: attached mtd4 (name "ubi", size 124 MiB)
[    1.002513] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.009277] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.015928] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[    1.022677] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[    1.028617] ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128
[    1.035797] ubi0: max/mean erase counter: 22/10, WL threshold: 4096, image sequence number: 0
[    1.044263] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
[    1.053476] ubi0: background thread "ubi_bgt0d" started, PID 451
[    1.056929] block ubiblock0_1: created from ubi0:1(rootfs)
[    1.064841] ubiblock: device ubiblock0_1 (rootfs) set to be root fil[    1.078437] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.087888] Freeing unused kernel memory: 1272K
[    1.090953] This architecture does not have kernel memory protection.
[    1.097381] Run /sbin/init as init process
[    1.710313] init: Console is alive
[    1.712634] init: - watchdog -
[    2.260762] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.363496] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.375873] SCSI subsystem initialized
[    2.382639] ehci-platform: EHCI generic platform driver
[    2.392959] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
[    2.399946] dwc2 1e101000.usb: Linked as a consumer to regulator.0
[    2.405948] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
[    2.515554] dwc2 1e101000.usb: DWC OTG Controller
[    2.518859] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
[    2.525914] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
[    2.532345] hub 1-0:1.0: USB hub found
[    2.534873] hub 1-0:1.0: 1 port detected
[    2.540098] dwc2 1e106000.usb: 1e106000.usb supply vusb_d not found, using dummy regulator
[    2.547211] dwc2 1e106000.usb: Linked as a consumer to regulator.0
[    2.553076] dwc2 1e106000.usb: 1e106000.usb supply vusb_a not found, using dummy regulator
[    2.663368] dwc2 1e106000.usb: DWC OTG Controller
[    2.666655] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2
[    2.673694] dwc2 1e106000.usb: irq 91, io mem 0x1e106000
[    2.680277] hub 2-0:1.0: USB hub found
[    2.682692] hub 2-0:1.0: 1 port detected
[    2.691822] usbcore: registered new interface driver usb-storage
[    2.696621] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.707361] init: - preinit -
[    3.442607] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    3.468992] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

[    6.776380] mount_root: loading kmods from internal overlay
[    6.807248] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.814433] kmodloader: done loading kernel modules from //etc/modules-boot.d/*

[    7.131250] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 547
[    7.177702] UBIFS (ubi0:7): recovery needed
[    7.281073] UBIFS (ubi0:7): recovery completed
[    7.284237] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data"
[    7.291871] UBIFS (ubi0:7): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.301715] UBIFS (ubi0:7): FS size: 76898304 bytes (73 MiB, 596 LEBs), journal size 3870720 bytes (3 MiB, 30 LEBs)
[    7.312104] UBIFS (ubi0:7): reserved for root: 3632096 bytes (3546 KiB)
[    7.318679] UBIFS (ubi0:7): media format: w4/r0 (latest is w5/r0), UUID E54322D9-9216-42DA-8978-48C4D1E7F934, small LPT model
[    7.330385] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    7.339166] block: extroot: not configured
[    7.359324] UBIFS (ubi0:7): un-mount UBI device 0
[    7.362612] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" stops
[    7.374403] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 550
[    7.474588] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data"
[    7.480993] UBIFS (ubi0:7): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.490837] UBIFS (ubi0:7): FS size: 76898304 bytes (73 MiB, 596 LEBs), journal size 3870720 bytes (3 MiB, 30 LEBs)
[    7.501183] UBIFS (ubi0:7): reserved for root: 3632096 bytes (3546 KiB)
[    7.507755] UBIFS (ubi0:7): media format: w4/r0 (latest is w5/r0), UUID E54322D9-9216-42DA-8978-48C4D1E7F934, small LPT model
[    7.702534] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    7.710420] block: extroot: not configured
[    7.728510] mount_root: switching to ubifs overlay
[    7.755991] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off.
[    7.768605] urandom-seed: Seeding with /etc/urandom.seed
[    7.892252] procd: - early -
[    7.893842] procd: - watchdog -
[    8.574618] procd: - watchdog -
[    8.576911] procd: - ubus -
[    8.649092] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.655781] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.661237] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.668980] procd: - init -
Please press Enter to activate this console.


BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r13401-1d6aff7d75
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@(none):/# [    9.671250] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.688441] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[    9.752787] xt_time: kernel timezone is -0000
[    9.785872] PPP generic driver version 2.4.2
[    9.791529] NET: Registered protocol family 24
[    9.810252] kmodloader: done loading kernel modules from /etc/modules.d/*
[    9.966157] urngd: v1.0.2 started.

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,913

Odp: DWR-966 bootowanie z NAND

bootcmd ci mówi co woła. Możesz spróbować ustawić większy f_kernel_size i zobaczysz co będzie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,913

Odp: DWR-966 bootowanie z NAND

Wystaw mi gdzieś zrzut oryginalnego flash.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

6 Odpowiedź przez olek210

  • Skąd: Warszawa
  • Zarejestrowany: 2017-04-09
  • Posty: 60

Odp: DWR-966 bootowanie z NAND

Paczka z partycjami.

7 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,913

Odp: DWR-966 bootowanie z NAND

Śmieszne jest to że oryginalny soft bazuje znów na stareńkim openwrt AA 12.09

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

8 Odpowiedź przez olek210 (edytowany przez olek210 2020-06-01 21:28:10)

  • Skąd: Warszawa
  • Zarejestrowany: 2017-04-09
  • Posty: 60

Odp: DWR-966 bootowanie z NAND

Pewnie dlatego, że SDK Lantiqa (UGW-6.1.1) bazowało na OpenWRT AA. W wersji 7.1.1 przerzucili się na OpenWRT CC. Z tego co widzę istnieje też fork OpenWRT bazujący na 19.07, ale wspiera chyba tylko nowsze SoC (XRX350 i te bazujące na x86).

Do tego routera są nawet kompletne źródła GPL [1] i podobno da się je zbudować. Obraz jest zaszyfrowany DES [2], ale klucz został złamany i jest znany ('97331723P02003'). DWR956 jest prawie identyczny i coś ktoś już z tym próbował robić [3] .

Tak czy siak z głównych rzeczy zostało jeszcze do rozkminienia PCI-E i ten bug z CRC. A z drobniejszych sterowanie LEDami od PHY i ewentualnie GPIO odcinające zasilanie USB(jeśli da się nim w ogóle sterować). Jakby się wszystko udało to by było świetnie smile


[1] https://github.com/brunompena/dwr-966
[2] https://freak.no/forum/showthread.php?t=289016
[3] https://github.com/adde88/DWR-956_decrypted_fw

9 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,913

Odp: DWR-966 bootowanie z NAND

Mam w pudle płytę od dwr-966, tyle że ona pochodzi z telenora i dotarła do mnie już ze spalonym modemem. Na niej nie chodzi w ogóle ethernet.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,913

Odp: DWR-966 bootowanie z NAND

Widziałem PR zgłoszony, szacun. Ciekawy jestem ile potrwa zanim dostanie się to do repo...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez Królik

  • Skąd: Warszawa
  • Zarejestrowany: 2015-07-10
  • Posty: 1,106

Odp: DWR-966 bootowanie z NAND

Cezary napisał/a:

Widziałem PR zgłoszony, szacun. Ciekawy jestem ile potrwa zanim dostanie się to do repo...

Pewnie zaraz po Check Poincie L-50, który dopiero 5 miesięcy czeka. wink

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Królik's Strona

12 Odpowiedź przez olek210 (edytowany przez olek210 2020-06-12 22:19:30)

  • Skąd: Warszawa
  • Zarejestrowany: 2017-04-09
  • Posty: 60

Odp: DWR-966 bootowanie z NAND

Ostatnio trzeba trochę poczekać smile
Ale na razie bez PCI-e. Bo muszę tą zabawę odłożyć na jakiś czas. A ze sterownikiem do pci-e jest dużo roboty. Ten z Openwrt działa tylko dla pierwszej magistrali. Akurat do tej do której jest podpięte ASM1042.
No i wolałem to rozbić na mniejsze części, powinno być szybciej.

13 Odpowiedź przez Królik (edytowany przez Królik 2020-06-13 04:51:07)

  • Skąd: Warszawa
  • Zarejestrowany: 2015-07-10
  • Posty: 1,106

Odp: DWR-966 bootowanie z NAND

A patrzyłeś w źródłach gpl czy nie da się zrobić factory działającego jako update z OFW?

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Królik's Strona

14 Odpowiedź przez olek210 (edytowany przez olek210 2020-06-13 13:06:40)

  • Skąd: Warszawa
  • Zarejestrowany: 2017-04-09
  • Posty: 60

Odp: DWR-966 bootowanie z NAND

Powinno się dać, ale jeszcze na to nie patrzyłem, wiem tylko, że ten obraz jest zaszyfrowany, ale klucz jest znany.

W końcu wczoraj wieczorem wpadł mi do głowy pomysł jak obejść problem ze złym CRC bez podmiany uboota. Przeglądając źródła GPL okazało się, że jest dodatkowa komenda mc (memory check)[1], która weryfikuje CRC. Jest ona uruchamiana w main jeszcze przed bootcmd. W przypadku każdego niepowodzenia zbootowania inkrementacje part1_err, a gdy on osiągnie 3 to uruchamia 'run red_led'. Więc wystarczy podmienić red_led na bootowanie i normalnie śmiga:  

setenv red_led run flash_flash
saveenv

Problemem jest to, że rozmiar kernela jest zahardkodowany do 2M [2], więc u-boot ładuje sobie do ram 2M a liczy CRC z całego kernela (2.3M).
Później jest śmieszna weryfikacja "CRC" z rootfs, które jest liczone jako suma kolejnych bajtów xD, więc ją można łatwo pominąć licząc ją z zera bajtów:

$ setenv f_rootfs_datalen 0
$ setenv f_rootfs_crc 0
$ setenv part1_err 0
$ setenv part2_err 0
$ saveenv
$ saveenv

Ale bez tego drugiego też działa bo cały czas part1_err=3 i za każdym razem przechodzi do red_led.

[1] https://github.com/brunompena/dwr-966/b … ade.c#L731
[2] https://github.com/brunompena/dwr-966/b … ade.c#L765

15 Odpowiedź przez smereka

  • Zarejestrowany: 2014-07-09
  • Posty: 2,437

Odp: DWR-966 bootowanie z NAND

Jakieś postępy w openwrt. Działa już może. Ktoś testował?