FAQ o OpenWrt | Sprzedam różne routery | Oddam

wo0t · 2020-03-02 12:20:17

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Temat: Huawei E3372 - Słabe transfery

Witam,
na wstępie byłem zmuszony założyć nowe konto. Starego dosłownie nie mogę odzyskać.

Mam BB 14.07 na WDR4300 i ostatnio stwierdziłem, że wykorzystam modem Huawei E3372 (E3372s-153) do połączenia WAN

Na TP-Linku śmiga OpenVPN jako klient, ebtables i parę innych usług.

Do rzeczy!...

modem wpięty.. config zrobiony dzięki tutkowi Cezarego https://eko.one.pl/?p=openwrt-3g

Modem łączy się tylko w trybie RAS ale z wielkim bółem, a w NCM wogole nie chce się połączyć.

config 'interface' 'wan'
option 'proto' '3g'
option 'device' '/dev/ttyUSB1'
option 'apn' 'internet'

# ifstatus wan

{
"up": true,
"pending": false,
"available": true,
"autostart": true,
"uptime": 4979,
"l3_device": "3g-wan",
"proto": "3g",
"updated": [
"addresses",
"routes"
],
"metric": 0,
"delegation": true,
"ipv4-address": [
{
"address": "100.71.132.153",
"mask": 32
}
],
"ipv6-address": [
],
"ipv6-prefix": [
],
"ipv6-prefix-assignment": [
],
"route": [
{
"target": "0.0.0.0",
"mask": 0,
"nexthop": "10.64.64.64",
"source": "0.0.0.0\/0"
}
],
"dns-server": [
"213.158.199.1",
"213.158.199.5"
],
"dns-search": [
],
"inactive": {
"ipv4-address": [
],
"ipv6-address": [
],
"route": [
],
"dns-server": [
],
"dns-search": [
]
},
"data": {
}
}

jak widać jest podłączony...

no to poniżej sprawdzimy stan...

# 3ginfo

Status: Połączony
Czas polaczenia: 0d, 01:24:04
Przeslano danych: 66.8 MiB / 55.8 MiB
Operator: T-Mobile
Tryb pracy: HSPA+
Sila sygnalu: 51%
Urzadzenie: huawei E3372
MCC MNC: 260 02
LAC: DED0 (57040)
LCID: 02C764A8 (46621864)
RNC: 02C7 (711)
eNB: - (-)
CID: 64A8 (25768)
CSQ: 16
RSSI: -81 dBm
RSCP: -80 dBm
Ec/IO: -8 dB
RSRP: - dBm
RSRQ: - dB

Transfery mam na poziomie 3/3 mbps - dramat.... gdzie ten sam modem w tej samej lokalizacji wyciąga lekko 40/15 mbps
czyli można sobie wybrazić jak działa VPN... i dostęp do usług na serwerze..

Generalnie to jest cud, że się łączy.. bo łączy się co 25 restart... serio... cały dzień kombinacje alpejskie, odpuściłem wieczorem kolo 23:00. Dziś w logach patrze, że o 3:45 nawiązał sobie połączenie do 8 rano potem padło i znowu sobie nawiązał koło 12 i działa do teraz...

w logu kernela gdy nie może się połączyć sypie cały czas..

[ 3503.910000] option1 ttyUSB1: option_instat_callback: error -2
[ 3506.520000] option1 ttyUSB1: option_instat_callback: error -2
[ 3508.240000] option1 ttyUSB1: option_instat_callback: error -2
[ 3509.310000] option1 ttyUSB1: option_instat_callback: error -2
[ 3511.910000] option1 ttyUSB1: option_instat_callback: error -2
[ 3513.630000] option1 ttyUSB1: option_instat_callback: error -2
[ 3514.700000] option1 ttyUSB1: option_instat_callback: error -2
[ 3517.320000] option1 ttyUSB1: option_instat_callback: error -2
[ 3519.030000] option1 ttyUSB1: option_instat_callback: error -2
[ 3520.100000] option1 ttyUSB1: option_instat_callback: error -2
[ 3522.710000] option1 ttyUSB1: option_instat_callback: error -2
[ 3524.430000] option1 ttyUSB1: option_instat_callback: error -2
[ 3525.500000] option1 ttyUSB1: option_instat_callback: error -2
[ 3528.110000] option1 ttyUSB1: option_instat_callback: error -2
[ 3529.830000] option1 ttyUSB1: option_instat_callback: error -2
[ 3530.900000] option1 ttyUSB1: option_instat_callback: error -2
[ 3533.510000] option1 ttyUSB1: option_instat_callback: error -2
[ 3535.240000] option1 ttyUSB1: option_instat_callback: error -2
[ 3536.310000] option1 ttyUSB1: option_instat_callback: error -2
[ 3538.930000] option1 ttyUSB1: option_instat_callback: error -2
[ 3540.650000] option1 ttyUSB1: option_instat_callback: error -2
[ 3541.720000] option1 ttyUSB1: option_instat_callback: error -2
[ 3544.340000] option1 ttyUSB1: option_instat_callback: error -2
[ 3546.060000] option1 ttyUSB1: option_instat_callback: error -2
[ 3547.130000] option1 ttyUSB1: option_instat_callback: error -2

# logread

Mon Mar 2 03:45:46 2020 daemon.notice netifd: Interface 'wan' is setting up now
Mon Mar 2 03:45:47 2020 daemon.info hostapd: wlan0: STA 7c:2a:31:a9:87:1f IEEE 802.11: authenticated
Mon Mar 2 03:45:47 2020 daemon.info hostapd: wlan0: STA 7c:2a:31:a9:87:1f IEEE 802.11: associated (aid 1)
Mon Mar 2 03:45:47 2020 daemon.info hostapd: wlan0: STA 7c:2a:31:a9:87:1f WPA: pairwise key handshake completed (RSN)
Mon Mar 2 03:45:47 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:47 2020 kern.err kernel: [ 5579.000000] option1 ttyUSB1: option_instat_callback: error -2
Mon Mar 2 03:45:48 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:48 2020 daemon.notice netifd: wan (26303): Trying to set mode
Mon Mar 2 03:45:48 2020 daemon.notice netifd: wan (26303): comgt 03:45:48 -> -- Error Report --
Mon Mar 2 03:45:48 2020 daemon.notice netifd: wan (26303): comgt 03:45:48 -> ----> ^
Mon Mar 2 03:45:48 2020 daemon.notice netifd: wan (26303): comgt 03:45:48 -> Error @163, line 10, Could not write to COM device. (1)
Mon Mar 2 03:45:48 2020 daemon.notice netifd: wan (26303):
Mon Mar 2 03:45:48 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:48 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:48 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:48 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:48 2020 daemon.warn odhcpd[1440]: DHCPV6 SOLICIT IA_NA from 0001000123e0731c309c23fcb741 on br-lan: no addresses available
Mon Mar 2 03:45:48 2020 kern.err kernel: [ 5580.070000] option1 ttyUSB1: option_instat_callback: error -2
Mon Mar 2 03:45:48 2020 daemon.notice pppd[26321]: pppd 2.4.7 started by root, uid 0
Mon Mar 2 03:45:49 2020 local2.info chat[26323]: abort on (BUSY)
Mon Mar 2 03:45:49 2020 local2.info chat[26323]: abort on (NO CARRIER)
Mon Mar 2 03:45:49 2020 local2.info chat[26323]: abort on (ERROR)
Mon Mar 2 03:45:49 2020 local2.info chat[26323]: report (CONNECT)
Mon Mar 2 03:45:49 2020 local2.info chat[26323]: timeout set to 10 seconds
Mon Mar 2 03:45:49 2020 local2.info chat[26323]: send (AT&F^M)
Mon Mar 2 03:45:50 2020 local2.info chat[26323]: expect (OK)
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq-dhcp[2589]: DHCPDISCOVER(br-lan) 7c:2a:31:a9:87:1f
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq-dhcp[2589]: DHCPOFFER(br-lan) 192.168.100.153 7c:2a:31:a9:87:1f
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq[2589]: read /etc/hosts - 1 addresses
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq[2589]: read /tmp/hosts/odhcpd - 0 addresses
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq[2589]: read /tmp/hosts/dhcp - 30 addresses
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq-dhcp[2589]: read /etc/ethers - 0 addresses
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq-dhcp[2589]: DHCPREQUEST(br-lan) 192.168.100.153 7c:2a:31:a9:87:1f
Mon Mar 2 03:45:50 2020 daemon.info dnsmasq-dhcp[2589]: DHCPACK(br-lan) 192.168.100.153 7c:2a:31:a9:87:1f Thomson
Mon Mar 2 03:45:50 2020 local2.info chat[26323]: AT&F^M^M
Mon Mar 2 03:45:50 2020 local2.info chat[26323]: +CME ERROR
Mon Mar 2 03:45:50 2020 local2.info chat[26323]: -- failed
Mon Mar 2 03:45:50 2020 local2.info chat[26323]: Failed (ERROR)
Mon Mar 2 03:45:50 2020 daemon.err pppd[26321]: Connect script failed
Mon Mar 2 03:45:51 2020 kern.err kernel: [ 5582.680000] option1 ttyUSB1: option_instat_callback: error -2
Mon Mar 2 03:45:51 2020 daemon.info pppd[26321]: Exit.
Mon Mar 2 03:45:51 2020 daemon.notice netifd: Interface 'wan' is now down
Mon Mar 2 03:45:51 2020 daemon.notice netifd: Interface 'wan' is setting up now
Mon Mar 2 03:45:53 2020 kern.err kernel: [ 5584.490000] option1 ttyUSB1: option_instat_callback: error -2
Mon Mar 2 03:45:54 2020 daemon.notice netifd: wan (26329): Trying to set mode
Mon Mar 2 03:45:55 2020 kern.err kernel: [ 5586.530000] option1 ttyUSB1: option_instat_callback: error -2
Mon Mar 2 03:45:55 2020 daemon.notice pppd[26349]: pppd 2.4.7 started by root, uid 0
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: abort on (BUSY)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: abort on (NO CARRIER)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: abort on (ERROR)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: report (CONNECT)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: timeout set to 10 seconds
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: send (AT&F^M)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: expect (OK)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: AT&F^M^M
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: OK
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: -- got it
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: send (ATE1^M)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: expect (OK)
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: ^M
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: ATE1^M^M
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: OK
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: -- got it
Mon Mar 2 03:45:56 2020 local2.info chat[26351]: send (AT+CGDCONT=1,"IP","internet"^M)
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: timeout set to 30 seconds
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: expect (OK)
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: ^M
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: AT+CGDCONT=1,"IP","internet"^M^M
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: OK
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: -- got it
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: send (ATD*99***1#^M)
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: expect (CONNECT)
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: ^M
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: ATD*99***1#^M^M
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: CONNECT
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: -- got it
Mon Mar 2 03:45:57 2020 local2.info chat[26351]: send ( ^M)
Mon Mar 2 03:45:57 2020 daemon.info pppd[26349]: Serial connection established.
Mon Mar 2 03:45:57 2020 daemon.info pppd[26349]: Using interface 3g-wan
Mon Mar 2 03:45:57 2020 daemon.notice pppd[26349]: Connect: 3g-wan <--> /dev/ttyUSB1
Mon Mar 2 03:46:00 2020 daemon.warn pppd[26349]: Could not determine remote IP address: defaulting to 10.64.64.64
Mon Mar 2 03:46:00 2020 daemon.notice pppd[26349]: local IP address 100.71.132.153
Mon Mar 2 03:46:00 2020 daemon.notice pppd[26349]: remote IP address 10.64.64.64
Mon Mar 2 03:46:00 2020 daemon.notice pppd[26349]: primary DNS address 213.158.199.1
Mon Mar 2 03:46:00 2020 daemon.notice pppd[26349]: secondary DNS address 213.158.199.5
Mon Mar 2 03:46:00 2020 daemon.notice netifd: Network device '3g-wan' link is up
Mon Mar 2 03:46:00 2020 daemon.notice netifd: Interface 'wan6' is enabled
Mon Mar 2 03:46:00 2020 daemon.notice netifd: Network alias '3g-wan' link is up
Mon Mar 2 03:46:00 2020 daemon.notice netifd: Interface 'wan6' has link connectivity
Mon Mar 2 03:46:00 2020 daemon.notice netifd: Interface 'wan6' is setting up now
Mon Mar 2 03:46:00 2020 daemon.notice netifd: Interface 'wan' is now up
Mon Mar 2 03:46:01 2020 user.notice firewall: Reloading firewall due to ifup of wan (3g-wan)
Mon Mar 2 03:46:02 2020 daemon.info dnsmasq[2589]: reading /tmp/resolv.conf.auto
Mon Mar 2 03:46:02 2020 daemon.info dnsmasq[2589]: using local addresses only for domain lan
Mon Mar 2 03:46:02 2020 daemon.info dnsmasq[2589]: using nameserver 8.8.8.8#53
Mon Mar 2 03:46:02 2020 daemon.info dnsmasq[2589]: using nameserver 8.8.4.4#53
Mon Mar 2 03:46:02 2020 daemon.info dnsmasq[2589]: using nameserver 213.158.199.1#53
Mon Mar 2 03:46:02 2020 daemon.info dnsmasq[2589]: using nameserver 213.158.199.5#53
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[2589]: exiting on receipt of SIGTERM
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: started, version 2.71 cachesize 150
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq-dhcp[26487]: DHCP, IP range 192.168.100.130 -- 192.168.100.159, lease time 12h
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: using local addresses only for domain lan
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: reading /tmp/resolv.conf.auto
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: using local addresses only for domain lan
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: using nameserver 8.8.8.8#53
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: using nameserver 8.8.4.4#53
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: using nameserver 213.158.199.1#53
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: using nameserver 213.158.199.5#53
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: read /etc/hosts - 1 addresses
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: read /tmp/hosts/dhcp - 30 addresses
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq[26487]: read /tmp/hosts/odhcpd - 0 addresses
Mon Mar 2 03:46:03 2020 daemon.info dnsmasq-dhcp[26487]: read /etc/ethers - 0 addresses
Mon Mar 2 10:46:02 2020 daemon.info pppd[26349]: System time change detected.

Jakieś sugestie?

Cezary · 2020-03-02 12:24:16

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,059

Odp: Huawei E3372 - Słabe transfery

I właśnie dlatego:
- zrób aktualizację routera do nowszej wersji softu
- podłącz modem przez hub usb z własnym zasilaniem
- podłącz modem przez jakiś kabel usb tak żeby go odsunąć od routera na jakąś odległość.
- przejdź na ncm, zobacz czy nie ma wyłączonym portów od ncm w konfiguracji (szukaj at^setport na forum).

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

wo0t · 2020-03-02 12:54:56

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Nie wiem czy udźwignę update do CC... bez utraty całego cfg.

Sprawdzę z hubem oraz na tym kablu.

NCM nadal nie bangla... chyba, że po przesiadce na CC się dogadają.

Porty sprawdzałem po przez picocom

AT^SETPORT?
^SETPORT:A1,A2;12,1,16,A1,A2
OK

marcin19883 · 2020-03-02 17:31:04

marcin19883
Użytkownik
Nieaktywny

Zarejestrowany: 2016-09-23
Posty: 426

Odp: Huawei E3372 - Słabe transfery

40/15 mbps na 3G? To niemoźliwe.

wo0t · 2020-03-02 21:57:27

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Modem podpięty pod PC zapina się na LTE i wyciąga takie wartości... pod OpenWRT łaczy tylko jako protokół RAS i max jaki wyciaga to 3/3

wo0t · 2020-03-05 00:16:35

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Cezary napisał/a:

I właśnie dlatego:
- zrób aktualizację routera do nowszej wersji softu
- podłącz modem przez hub usb z własnym zasilaniem
- podłącz modem przez jakiś kabel usb tak żeby go odsunąć od routera na jakąś odległość.
- przejdź na ncm, zobacz czy nie ma wyłączonym portów od ncm w konfiguracji (szukaj at^setport na forum).

Tak więc Wielki Cesarze

Zrobiłem upgrade z BB 14.07 do 18.06.. w sumie myślałem o wersji 19..ale tam nie znalazłem obrazu do WDR4300 ,a do 4310 i nie do końca byłem przekonany czy to zadziała.

po update..
modem sam z siebie w auto magiczny sposób podłącza sie po NCM i zapina jak LTE trasfery w okolicach 40mbps...
dodatkowo podłączenie jego przez hub z zasilaniem rozwiązuje problem z spadkami napięcia..

Mam tylko jeden no.. dwa problemy...

Pierwszy tyczy się samego modemu... co któryś restart rouerka.. OpenWRT nie widzi modemu.. muszę z Luci wyłączyć i ponownie włączyć interface... lub wypiąć i wpiąć raz jeszcze modem. Myślę ze to kwestia kolejności ładowania urządzeń przez port USB... chociaż Pendrive jako exroot zawsze się prawidłowo montuje...

drugi problem.. tyczy się VPN... cfg zrobiłem kopie z BB 14.07 tak samo jak klucze... przez Luci to w ogóle cfg się rozjeżdża. OK łączy się... po stronie klienta jak i serwera pokazuje, że połączenie nawiązane, ale ping na serwer nie leci.. tak samo siec lan po stronie innych klientów jak i serwera - nie można przeglądać. Porównywałem cfg firewalla czy VPN z BB 14.07 gdzie wszystko ładnie śmigało.

Na innych klientach Linksys i Tenda bez problemu działa sieć lan pingi etc.. cfg są identyczne.. ehh coś pominąłem i teraz się będę srać bez nc+ i zrywającym netem.

Cezary masz jakieś propozycje?

Cezary · 2020-03-05 06:37:19

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,059

Odp: Huawei E3372 - Słabe transfery

Jesteś następnym użytkownikiem który nie czyta. Obrazy są albo w ath79 albo w ar71xx, w zależności od tego czy został już przepisany czy jeszcze nie.

1. Nie widzi modemu czy nie przełączył urządzenia? Kolejność ładowania sterowników nie ma w tym przypadku znaczenia.
2. Zweryfikuj więc konfig. "Przeniosłem i nie działa" kompletnie nic nie oznacza.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

wo0t · 2020-03-08 13:09:03

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Czytam czytam...

obrazów szukałem tutaj do 4300... jest do 4310.. wiec nie ryzkowalem. Dalej nie szukałem..
https://dl.eko.one.pl/luci/openwrt-19.0 … x/generic/

Teraz cfg które przepisałem do Nowego openWRT działa jak najbardziej.. tylko problem był z VPN, że mimo się łączył to nie można było przeglądać sieci LAN. Okazało się, że w moście nie było interfejsu tap0 - Teraz wszystko śmiga.

Pozostaje kwestia modemu po restarcie routera. Czasem 10x pod rząd się połączy, a czasem właśnie nie widzi modemu.

Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.000000] Linux version 4.9.199 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Sun Nov 17 01:49:52 2019
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] MyLoader: sysp=d41aa8a5, boardp=3bb52003, parts=bd952718
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] SoC: Atheros AR9344 rev 2
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Determined physical RAM map:
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] memory: 08000000 @ 00000000 (usable)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Zone ranges:
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Movable zone start for each node
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Early memory node ranges
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] On node 0 totalpages: 32768
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 80450454, node_mem_map 81000020
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] Normal zone: 256 pages used for memmap
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs noinitrd
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] NR_IRQS:51
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.000010] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.008320] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.081145] pid_max: default: 32768 minimum: 301
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.086170] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.093219] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.103440] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.113932] futex hash table entries: 256 (order: -1, 3072 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.121640] NET: Registered protocol family 16
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.127874] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 0.136968] registering PCI controller with io_map_base unset
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.391718] PCI host bridge to bus 0000:00
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.396096] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.403454] pci_bus 0000:00: root bus resource [io 0x0000]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.409383] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.416618] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.425079] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
Sun Mar 8 12:30:37 2020 kern.err kernel: [ 0.425091] pci 0000:00:00.0: invalid calibration data
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.430596] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.430650] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.430725] pci 0000:00:00.0: supports D1
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.430735] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.430974] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.431003] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.438802] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.446524] pci 0000:00:00.0: using irq 40 for pin 1
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.455016] clocksource: Switched to clocksource MIPS
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.461502] NET: Registered protocol family 2
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.467110] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.474539] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.481354] TCP: Hash tables configured (established 1024 bind 1024)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.488211] UDP hash table entries: 256 (order: 0, 4096 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.494441] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.501392] NET: Registered protocol family 1
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 0.506108] PCI: CLS 0 bytes, default 32
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 0.508890] Crashlog allocated RAM at address 0x3f00000
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.515593] workingset: timestamp_bits=30 max_order=15 bucket_order=0
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.529714] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.535962] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.555548] io scheduler noop registered
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.559720] io scheduler deadline registered (default)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.565647] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.575217] console [ttyS0] disabled
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.599096] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.608290] console [ttyS0] enabled
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.615712] bootconsole [early0] disabled
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 0.630243] m25p80 spi0.0: found s25fl064k, expected m25p80
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.648316] m25p80 spi0.0: s25fl064k (8192 Kbytes)
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.653477] 5 tp-link partitions found on MTD device spi0.0
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.659174] Creating 5 MTD partitions on "spi0.0":
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.664043] 0x000000000000-0x000000020000 : "u-boot"
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.670986] 0x000000020000-0x0000001725a8 : "kernel"
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.678073] 0x0000001725a8-0x0000007f0000 : "rootfs"
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.684710] mtd: device 2 (rootfs) set to be root filesystem
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.690542] 1 squashfs-split partitions found on MTD device rootfs
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.696834] 0x000000630000-0x0000007f0000 : "rootfs_data"
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.704434] 0x0000007f0000-0x000000800000 : "art"
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 0.711305] 0x000000020000-0x0000007f0000 : "firmware"
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.719581] libphy: Fixed MDIO Bus: probed
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 0.735659] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 1.407310] libphy: ag71xx_mdio: probed
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.036413] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.047934] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.056283] NET: Registered protocol family 10
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.064747] NET: Registered protocol family 17
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.069369] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.082631] 8021q: 802.1Q VLAN Support v1.8
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.088670] hctosys: unable to open rtc device (rtc0)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.098313] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 2.106908] Freeing unused kernel memory: 308K
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 2.111415] This architecture does not have kernel memory protection.
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 2.565030] random: fast init done
Sun Mar 8 12:30:37 2020 user.info kernel: [ 2.787414] init: Console is alive
Sun Mar 8 12:30:37 2020 user.info kernel: [ 2.791068] init: - watchdog -
Sun Mar 8 12:30:37 2020 user.info kernel: [ 4.408410] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.637372] usbcore: registered new interface driver usbfs
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.643025] usbcore: registered new interface driver hub
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.648557] usbcore: registered new device driver usb
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.685498] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 4.700940] SCSI subsystem initialized
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.709555] ehci-platform: EHCI generic platform driver
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.714950] ehci-platform ehci-platform: EHCI Host Controller
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.720862] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.730986] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.765104] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.772414] hub 1-0:1.0: USB hub found
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.776595] hub 1-0:1.0: 1 port detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.785174] usbcore: registered new interface driver usb-storage
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 4.793386] usbcore: registered new interface driver uas
Sun Mar 8 12:30:37 2020 user.info kernel: [ 4.799453] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Sun Mar 8 12:30:37 2020 user.info kernel: [ 4.817242] init: - preinit -
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 5.376348] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 5.732618] hub 1-1:1.0: USB hub found
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 5.745277] hub 1-1:1.0: 4 ports detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 5.779265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 5.857269] random: procd: uninitialized urandom read (4 bytes read)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.075034] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.238022] hub 1-1.1:1.0: USB hub found
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.242658] hub 1-1.1:1.0: 4 ports detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.575036] usb 1-1.1.2: new high-speed USB device number 4 using ehci-platform
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.757240] usb-storage 1-1.1.2:1.3: USB Mass Storage device detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.764774] scsi host0: usb-storage 1-1.1.2:1.3
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.771028] usb-storage 1-1.1.2:1.4: USB Mass Storage device detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.778304] scsi host1: usb-storage 1-1.1.2:1.4
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.836275] eth0: link up (1000Mbps/Full duplex)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.841056] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 6.885057] usb 1-1.1.4: new high-speed USB device number 5 using ehci-platform
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 7.046754] usb-storage 1-1.1.4:1.0: USB Mass Storage device detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 7.054005] scsi host2: usb-storage 1-1.1.4:1.0
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 7.799029] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 7.809438] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 7.822317] sd 1:0:0:0: [sda] Attached SCSI removable disk
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 8.116259] scsi 2:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 8.127148] sd 2:0:0:0: [sdb] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 8.135297] sd 2:0:0:0: [sdb] Write Protect is off
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 8.140175] sd 2:0:0:0: [sdb] Mode Sense: 4f 00 00 00
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 8.140666] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 8.155909] sdb: sdb1
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 8.161419] sd 2:0:0:0: [sdb] Attached SCSI removable disk
Sun Mar 8 12:30:37 2020 user.info kernel: [ 9.029148] mount_root: loading kmods from internal overlay
Sun Mar 8 12:30:37 2020 user.info kernel: [ 9.080595] kmodloader: loading kernel modules from //etc/modules-boot.d/*
Sun Mar 8 12:30:37 2020 user.info kernel: [ 9.089333] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 9.745775] jffs2: notice: (517) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sun Mar 8 12:30:37 2020 user.info kernel: [ 9.761885] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 17.333857] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts:
Sun Mar 8 12:30:37 2020 user.notice kernel: [ 17.366591] mount_root: switched to extroot
Sun Mar 8 12:30:37 2020 user.warn kernel: [ 17.380660] urandom-seed: Seeding with /etc/urandom.seed
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 17.495696] eth0: link down
Sun Mar 8 12:30:37 2020 user.info kernel: [ 17.522746] procd: - early -
Sun Mar 8 12:30:37 2020 user.info kernel: [ 17.525862] procd: - watchdog -
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 17.854241] random: jshn: uninitialized urandom read (4 bytes read)
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 18.063503] random: jshn: uninitialized urandom read (4 bytes read)
Sun Mar 8 12:30:37 2020 user.info kernel: [ 18.146339] procd: - watchdog -
Sun Mar 8 12:30:37 2020 user.info kernel: [ 18.149801] procd: - ubus -
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 18.172983] random: ubusd: uninitialized urandom read (4 bytes read)
Sun Mar 8 12:30:37 2020 user.info kernel: [ 18.207620] procd: - init -
Sun Mar 8 12:30:37 2020 user.info kernel: [ 19.256126] kmodloader: loading kernel modules from /etc/modules.d/*
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.340692] tun: Universal TUN/TAP device driver, 1.6
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.345876] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.393166] ip6_tables: (C) 2000-2006 Netfilter Core Team
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.431981] fuse init (API version 7.26)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.503995] usbcore: registered new interface driver cdc_acm
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.509805] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.534035] usbcore: registered new interface driver cdc_wdm
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.549226] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.557401] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.646598] Ebtables v2.0 registered
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.666962] ip_tables: (C) 2000-2006 Netfilter Core Team
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 19.699931] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.088634] usbcore: registered new interface driver usblp
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.127042] usbcore: registered new interface driver usbserial
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.133056] usbcore: registered new interface driver usbserial_generic
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.139826] usbserial: USB Serial support registered for generic
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.207392] xt_time: kernel timezone is -0000
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.217283] usbcore: registered new interface driver cdc_ether
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.237822] usbcore: registered new interface driver cdc_ncm
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.385282] huawei_cdc_ncm 1-1.1.2:1.2: MAC-Address: 00:1e:10:1f:00:00
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.391933] huawei_cdc_ncm 1-1.1.2:1.2: setting rx_max = 16384
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.420545] huawei_cdc_ncm 1-1.1.2:1.2: NDP will be placed at end of frame for this device.
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.429322] huawei_cdc_ncm 1-1.1.2:1.2: cdc-wdm0: USB WDM device
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.436637] huawei_cdc_ncm 1-1.1.2:1.2 wwan0: register 'huawei_cdc_ncm' at usb-ehci-platform-1.1.2, Huawei CDC NCM device, 00:1e:10:1f:00:00
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.449618] usbcore: registered new interface driver huawei_cdc_ncm
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.598633] PPP generic driver version 2.4.2
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.616321] NET: Registered protocol family 24
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.623982] usbcore: registered new interface driver qmi_wwan
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.644105] usbcore: registered new interface driver rndis_host
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.660131] usbcore: registered new interface driver sierra
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.665955] usbserial: USB Serial support registered for Sierra USB modem
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.697240] usbcore: registered new interface driver sierra_net
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.777474] usbcore: registered new interface driver cdc_mbim
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.789976] usbcore: registered new interface driver option
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.795807] usbserial: USB Serial support registered for GSM modem (1-port)
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.803378] option 1-1.1.2:1.0: GSM modem (1-port) converter detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.810239] usb 1-1.1.2: GSM modem (1-port) converter now attached to ttyUSB0
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.817633] option 1-1.1.2:1.1: GSM modem (1-port) converter detected
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.824467] usb 1-1.1.2: GSM modem (1-port) converter now attached to ttyUSB1
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.886606] usbcore: registered new interface driver qcserial
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.892542] usbserial: USB Serial support registered for Qualcomm USB modem
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.942125] ath: EEPROM regdomain: 0x0
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.942133] ath: EEPROM indicates default country code should be used
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.942137] ath: doing EEPROM country->regdmn map search
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.942153] ath: country maps to regdmn code: 0x3a
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.942159] ath: Country alpha2 being used: US
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.942163] ath: Regpair used: 0x3a
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.954398] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.958344] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
Sun Mar 8 12:30:37 2020 kern.warn kernel: [ 20.965300] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.976343] ath: EEPROM regdomain: 0x0
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.976350] ath: EEPROM indicates default country code should be used
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.976354] ath: doing EEPROM country->regdmn map search
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.976369] ath: country maps to regdmn code: 0x3a
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.976375] ath: Country alpha2 being used: US
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.976379] ath: Regpair used: 0x3a
Sun Mar 8 12:30:37 2020 kern.debug kernel: [ 20.986738] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Sun Mar 8 12:30:37 2020 kern.info kernel: [ 20.990649] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
Sun Mar 8 12:30:37 2020 user.info kernel: [ 21.065485] kmodloader: done loading kernel modules from /etc/modules.d/*
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 22.027974] random: crng init done
Sun Mar 8 12:30:37 2020 kern.notice kernel: [ 22.031440] random: 6 urandom warning(s) missed due to ratelimiting
Sun Mar 8 12:30:38 2020 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sun Mar 8 12:30:38 2020 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sun Mar 8 12:30:38 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: started, version 2.80 cachesize 150
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: DNS service limited to local subnets
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain test
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain onion
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain localhost
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain local
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain invalid
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain bind
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: using local addresses only for domain lan
Sun Mar 8 12:30:39 2020 daemon.warn dnsmasq[1179]: no servers found in /tmp/resolv.conf.auto, will retry
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: read /etc/hosts - 4 addresses
Sun Mar 8 12:30:39 2020 daemon.info dnsmasq[1179]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Sun Mar 8 12:30:39 2020 authpriv.info dropbear[1237]: Not backgrounding
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: tunnel
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: Network device
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: bridge
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: veth
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: macvlan
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: 8021ad
Sun Mar 8 12:30:42 2020 user.notice : Added device handler type: 8021q
Sun Mar 8 12:30:44 2020 daemon.err block: /dev/mtdblock2 is already mounted on /rom
Sun Mar 8 12:30:44 2020 daemon.err block: /dev/sdb1 is already mounted on /
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.142937] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.168150] br-lan: port 1(eth0.1) entered blocking state
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.173638] br-lan: port 1(eth0.1) entered disabled state
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.179609] device eth0.1 entered promiscuous mode
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.184475] device eth0 entered promiscuous mode
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'lan' is enabled
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'lan' is setting up now
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.215280] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'lan' is now up
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: reading /tmp/resolv.conf.auto
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain test
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain onion
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain localhost
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain local
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain invalid
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain bind
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using local addresses only for domain lan
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using nameserver 8.8.8.8#53
Sun Mar 8 12:30:49 2020 daemon.info dnsmasq[1179]: using nameserver 8.8.4.4#53
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'loopback' is enabled
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'loopback' is setting up now
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'loopback' is now up
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'wan' is setting up now
Sun Mar 8 12:30:49 2020 kern.info kernel: [ 35.596371] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Sun Mar 8 12:30:49 2020 daemon.notice netifd: Interface 'wan6' is enabled
Sun Mar 8 12:30:50 2020 daemon.notice netifd: Network device 'lo' link is up
Sun Mar 8 12:30:50 2020 daemon.notice netifd: Interface 'loopback' has link connectivity
Sun Mar 8 12:30:50 2020 kern.info kernel: [ 36.196540] eth0: link up (1000Mbps/Full duplex)
Sun Mar 8 12:30:50 2020 kern.info kernel: [ 36.201299] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sun Mar 8 12:30:50 2020 daemon.notice netifd: VLAN 'eth0.1' link is up
Sun Mar 8 12:30:50 2020 daemon.notice netifd: VLAN 'eth0.2' link is up
Sun Mar 8 12:30:50 2020 daemon.notice netifd: Interface 'wan6' has link connectivity
Sun Mar 8 12:30:50 2020 daemon.notice netifd: Interface 'wan6' is setting up now
Sun Mar 8 12:30:50 2020 daemon.notice netifd: Network device 'eth0' link is up
Sun Mar 8 12:30:50 2020 kern.info kernel: [ 36.295142] br-lan: port 1(eth0.1) entered blocking state
Sun Mar 8 12:30:50 2020 kern.info kernel: [ 36.300637] br-lan: port 1(eth0.1) entered forwarding state
Sun Mar 8 12:30:50 2020 kern.info kernel: [ 36.306495] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Sun Mar 8 12:30:50 2020 daemon.notice netifd: bridge 'br-lan' link is up
Sun Mar 8 12:30:50 2020 daemon.notice netifd: Interface 'lan' has link connectivity
Sun Mar 8 12:30:50 2020 kern.info kernel: [ 36.445107] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sun Mar 8 12:30:50 2020 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sun Mar 8 12:30:51 2020 daemon.err odhcp6c[1825]: Failed to send RS (Address not available)
Sun Mar 8 12:30:51 2020 daemon.err odhcp6c[1825]: Failed to send DHCPV6 message to ff02::1:2 (Address not available)
Sun Mar 8 12:30:53 2020 daemon.notice netifd: wan (1683): WARNING: Variable 'error' does not exist or is not an array/object
Sun Mar 8 12:30:53 2020 daemon.notice netifd: wan (1683): Unsupported modem
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.130914] ath: EEPROM regdomain: 0x8268
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.135057] ath: EEPROM indicates we should expect a country code
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.141236] ath: doing EEPROM country->regdmn map search
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.146648] ath: country maps to regdmn code: 0x37
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.151511] ath: Country alpha2 being used: PL
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.156032] ath: Regpair used: 0x37
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.159567] ath: regdomain 0x8268 dynamically updated by user
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.165486] ath: EEPROM regdomain: 0x8268
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.169552] ath: EEPROM indicates we should expect a country code
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.175747] ath: doing EEPROM country->regdmn map search
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.181135] ath: country maps to regdmn code: 0x37
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.186003] ath: Country alpha2 being used: PL
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.190504] ath: Regpair used: 0x37
Sun Mar 8 12:30:53 2020 kern.debug kernel: [ 39.194045] ath: regdomain 0x8268 dynamically updated by user
Sun Mar 8 12:30:53 2020 daemon.notice netifd: wan (1937): Stopping network wan
Sun Mar 8 12:30:54 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna all all
Sun Mar 8 12:30:54 2020 user.notice mac80211: Failed command: iw phy phy1 set antenna all all
Sun Mar 8 12:30:54 2020 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/dhcp
Sun Mar 8 12:30:55 2020 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/radvd
Sun Mar 8 12:30:55 2020 daemon.notice netifd: wan (1937): sending ->
Sun Mar 8 12:30:55 2020 user.notice ucitrack: Setting up /etc/config/wireless reload dependency on /etc/config/network
Sun Mar 8 12:30:55 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Sun Mar 8 12:30:55 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.428252] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Sun Mar 8 12:30:55 2020 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/luci-splash
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.468394] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.571279] br-lan: port 2(wlan1) entered blocking state
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.576745] br-lan: port 2(wlan1) entered disabled state
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.582592] device wlan1 entered promiscuous mode
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.587529] br-lan: port 2(wlan1) entered blocking state
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.592930] br-lan: port 2(wlan1) entered forwarding state
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.603514] br-lan: port 3(wlan0) entered blocking state
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.608984] br-lan: port 3(wlan0) entered disabled state
Sun Mar 8 12:30:55 2020 kern.info kernel: [ 41.614797] device wlan0 entered promiscuous mode
Sun Mar 8 12:30:55 2020 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/qos
Sun Mar 8 12:30:56 2020 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Mar 8 12:30:56 2020 daemon.err hostapd: Using interface wlan0 with hwaddr 10:fe:ed:e6:31:c1 and ssid "M#_Koldrix"
Sun Mar 8 12:30:56 2020 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Sun Mar 8 12:30:56 2020 daemon.err hostapd: Using interface wlan1 with hwaddr 10:fe:ed:e6:31:c2 and ssid "M#_Koldrix_5Ghz"
Sun Mar 8 12:30:56 2020 user.notice ucitrack: Setting up /etc/config/firewall reload dependency on /etc/config/miniupnpd
Sun Mar 8 12:30:56 2020 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/odhcpd
Sun Mar 8 12:30:56 2020 kern.info kernel: [ 42.435120] br-lan: port 2(wlan1) entered disabled state
Sun Mar 8 12:30:57 2020 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Sun Mar 8 12:30:57 2020 kern.info kernel: [ 43.373206] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sun Mar 8 12:30:57 2020 kern.info kernel: [ 43.379895] br-lan: port 3(wlan0) entered blocking state
Sun Mar 8 12:30:57 2020 kern.info kernel: [ 43.385337] br-lan: port 3(wlan0) entered forwarding state
Sun Mar 8 12:30:57 2020 kern.info kernel: [ 43.438757] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Sun Mar 8 12:30:57 2020 kern.info kernel: [ 43.445428] br-lan: port 2(wlan1) entered blocking state
Sun Mar 8 12:30:57 2020 kern.info kernel: [ 43.450849] br-lan: port 2(wlan1) entered forwarding state
Sun Mar 8 12:30:57 2020 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Sun Mar 8 12:30:57 2020 daemon.notice hostapd: wlan1: AP-ENABLED
Sun Mar 8 12:30:57 2020 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->ENABLED
Sun Mar 8 12:30:57 2020 daemon.notice hostapd: wlan0: AP-ENABLED
Sun Mar 8 12:30:57 2020 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Sun Mar 8 12:30:58 2020 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/luci_statistics
Sun Mar 8 12:30:58 2020 daemon.notice netifd: Network device 'wlan0' link is up
Sun Mar 8 12:30:58 2020 daemon.notice netifd: Network device 'wlan1' link is up
Sun Mar 8 12:30:58 2020 user.notice ucitrack: Setting up /etc/config/system reload dependency on /etc/config/dhcp
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[1179]: exiting on receipt of SIGTERM
Sun Mar 8 12:30:58 2020 daemon.notice netifd: Interface 'wan' is now down
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: started, version 2.80 cachesize 150
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: DNS service limited to local subnets
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq-dhcp[2251]: DHCP, IP range 192.168.100.50 -- 192.168.100.149, lease time 12h
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain test
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain onion
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain localhost
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain local
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain invalid
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain bind
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain lan
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: reading /tmp/resolv.conf.auto
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain test
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain onion
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain localhost
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain local
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain invalid
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain bind
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using local addresses only for domain lan
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using nameserver 8.8.8.8#53
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: using nameserver 8.8.4.4#53
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: read /etc/hosts - 4 addresses
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq-dhcp[2251]: read /etc/ethers - 0 addresses
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: read /etc/hosts - 4 addresses
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq[2251]: read /tmp/hosts/dhcp.cfg01411c - 1 addresses
Sun Mar 8 12:30:58 2020 daemon.info dnsmasq-dhcp[2251]: read /etc/ethers - 0 addresses
Sun Mar 8 12:31:01 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led USB1
Sun Mar 8 12:31:01 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led USB2
Sun Mar 8 12:31:01 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led WLAN2G
Sun Mar 8 12:31:02 2020 daemon.info procd: - init complete -

Cezary · 2020-03-08 13:15:09

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,059

Odp: Huawei E3372 - Słabe transfery

Napisałem że obrazy są albo w ath79 albo ar71xx, skoro ich nie ma w ar71xx to gdzie są? W ath79... https://dl.eko.one.pl/luci/openwrt-19.07/ath79/generic/

Sun Mar  8 12:30:53 2020 daemon.notice netifd: wan (1683): WARNING: Variable 'error' does not exist or is not an array/object
Sun Mar  8 12:30:53 2020 daemon.notice netifd: wan (1683): Unsupported modem

Masz faktycznie E3372 czy masz rosyjską odmianę typu M150 czy coś podobnego? A może soft masz zmieniony? Bo ten modem nie przedstawił się jako huawei albo jest problem z jego odczytem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

wo0t · 2020-03-08 13:20:03

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Jest to orginał z Play. Kiedyś dostałem za darmo od operatora i teraz stwierdziłem, że go wykorzystam. Podejrzewasz, że soft się sypie lub modem?

Cezary · 2020-03-08 13:24:15

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,059

Odp: Huawei E3372 - Słabe transfery

Skrypt od ncm w openwrt najpierw pytają się modemu czym on jest, żeby wybrać odpowiednie polecenia startowe. Jak nie dogada się z modemem lub jest to inny typ to połączenia nie będzie.
Napisałeś że czasami nie widzi modemu. Być może to jest właśnie spowodowane tym co zacytowałem powyżej - modem jest wykryty ale skrypt nie dogadały się modem i napisały że to nieobsługiwany modem. Więc jest jakiś problem z odczytem danych z modemu. A tym bardziej że zdarza się to raz na jakiś czas, więc coś się dzieje z modemem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

wo0t · 2020-03-08 13:29:31

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

a podłączenie przez Hub aktywnego może mieć jakiś wpływ?

Cezary · 2020-03-08 13:36:22

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,059

Odp: Huawei E3372 - Słabe transfery

Hub jest przezroczysty, więc nie. Chyba że masz huba wyjątkowo podłej jakości, ale to byś widział w logach - miałbyś informacje o błędach na magistrali usb, rozłączeniach urządzenia, problemach z EMI itp.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

wo0t · 2020-03-09 12:50:32

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Chyba nie pozostaje mi nic innego jak zrobić skrypt który będzie pingować np google.. jak nie dostanie odpowiedzi to sprawdza czy dostępny jest interface wwan+ jak tak to robi restart całego routerka... bo tylko tak zaskakuje modem. Jezeli nie ma wwan+ tzn. ze jest połączenie po kablu. Chyba dobrze rozumuje... wrzucić skrypt do crona co 5min.

Druga sprawa.. mam zainstalowane ebtables. W luCi w zaporze dodałem:

ebtables -A INPUT --in-interface tap0 --protocol ipv4 --ip-protocol udp --ip-destination-port 67:68 -j DROP
ebtables -A INPUT --in-interface tap0 --protocol ipv4 --ip-protocol udp --ip-source-port 67:68 -j DROP
ebtables -A FORWARD --out-interface tap0 --protocol ipv4 --ip-protocol udp --ip-destination-port 67:68 -j DROP
ebtables -A FORWARD --out-interface tap0 --protocol ipv4 --ip-protocol udp --ip-source-port 67:68 -j DROP

Mimo to DHCP przepuszcza z innego routerka, który ma ograniczony flash oraz brak usb wiec sieje po całej sieci VPN swoim DHCP. i każdy inny miał to wycinać. Szkoda, że teraz tak regułka coś nie bangla...

wo0t · 2020-03-09 15:06:00

wo0t
Użytkownik
Nieaktywny

Zarejestrowany: 2020-03-02
Posty: 25

Odp: Huawei E3372 - Słabe transfery

Jeżeli chodzi o ebtables to znalazłem taki błąd dopiero po wpisaniu z rączki komendy...

Unable to update the kernel. Two possible causes:
1. Multiple ebtables programs were executing simultaneously. The ebtables
userspace tool doesn't by default support multiple ebtables programs running
concurrently. The ebtables option --concurrent or a tool like flock can be
used to support concurrent scripts that update the ebtables kernel tables.
2. The kernel doesn't support a certain ebtables extension, consider
recompiling your kernel or insmod the extension.

doinstalowanie pakietu:

kmod-ebtables-ipv4

rozwiązało problem ebtables. Regułki z blokada DHCP działają.

Pozostaje kwestia tylko modemu...

mikewse · 2020-07-19 18:41:55

mikewse
Użytkownik
Nieaktywny

Zarejestrowany: 2020-07-19
Posty: 1

Odp: Huawei E3372 - Słabe transfery

Sun Mar  8 12:30:53 2020 daemon.notice netifd: wan (1683): WARNING: Variable 'error' does not exist or is not an array/object
Sun Mar  8 12:30:53 2020 daemon.notice netifd: wan (1683): Unsupported modem

I had the same problem with my E3276 and I needed to increase the delay in OpenWrt interface settings, see more here:
https://forum.openwrt.org/t/needed-to-i … 07-3/69678

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Huawei E3372 - Słabe transfery

Posty: 16

1 Temat przez wo0t 2020-03-02 12:20:17

Temat: Huawei E3372 - Słabe transfery

2 Odpowiedź przez Cezary 2020-03-02 12:24:16

Odp: Huawei E3372 - Słabe transfery

3 Odpowiedź przez wo0t 2020-03-02 12:54:56

Odp: Huawei E3372 - Słabe transfery

4 Odpowiedź przez marcin19883 2020-03-02 17:31:04

Odp: Huawei E3372 - Słabe transfery

5 Odpowiedź przez wo0t 2020-03-02 21:57:27

Odp: Huawei E3372 - Słabe transfery

6 Odpowiedź przez wo0t 2020-03-05 00:16:35

Odp: Huawei E3372 - Słabe transfery

7 Odpowiedź przez Cezary 2020-03-05 06:37:19

Odp: Huawei E3372 - Słabe transfery

8 Odpowiedź przez wo0t 2020-03-08 13:09:03

Odp: Huawei E3372 - Słabe transfery

9 Odpowiedź przez Cezary 2020-03-08 13:15:09

Odp: Huawei E3372 - Słabe transfery

10 Odpowiedź przez wo0t 2020-03-08 13:20:03

Odp: Huawei E3372 - Słabe transfery

11 Odpowiedź przez Cezary 2020-03-08 13:24:15

Odp: Huawei E3372 - Słabe transfery

12 Odpowiedź przez wo0t 2020-03-08 13:29:31

Odp: Huawei E3372 - Słabe transfery

13 Odpowiedź przez Cezary 2020-03-08 13:36:22

Odp: Huawei E3372 - Słabe transfery

14 Odpowiedź przez wo0t 2020-03-09 12:50:32

Odp: Huawei E3372 - Słabe transfery

15 Odpowiedź przez wo0t 2020-03-09 15:06:00

Odp: Huawei E3372 - Słabe transfery

16 Odpowiedź przez mikewse 2020-07-19 18:41:55

Odp: Huawei E3372 - Słabe transfery

Posty: 16