Czy przyczyną zwieszania routera może być że wszystko chodzi na pasywnym hubie?? bo wszystko jest w porządku do momentu jak włącze odtwarzanie strumienia radiowego, chwile pogra i nagle jak by sie zrestartował tzn jak wpisze mpc stop to pisze ze albo brak połączenia albo MC to nie znaleziono i tak jest z każdą komendą wyjęcie wtyczki dopiero pomaga.

TL-WR1043ND: HDD-USB, extroot, LCD, Pilot, MP3 - Radio Player, NAS, Torrent, FTP, Sterowanie głosem, Komunikaty Głosowe, Termometr, PowerSwitch - Sterownik oświetlenia, Budzik, LTE - ODU IDU 200
Raspberry Pi + HDMI-VGA + Lcd Controller + Lcd z laptopa = Pogodynka

mpc add http://scfire-dtc-aa03.stream.aol.com:80/stream/1035
root@Gargoyle:~$ mpc play
http://scfire-dtc-aa03.stream.aol.com:80/stream/1035
[playing] #1/1   0:00/0:00 (0%)
volume:  6%   repeat: off   random: off   single: off   consume: off
root@Gargoyle:~$ mpd
mpd: can't load library 'libfaad.so.2'
root@Gargoyle:~$ mc
-ash: mc: not found

mc wpisalem dla testu
pogra okolo 11 sekund i cisza
co to może być został mi tylko ten problem bo wszystko już udało mi się naprawić

aha i jeszcze czasem mi cos takiego wywali
root@Gargoyle:~$ mpd
Failed to bind to '[::]:6600': Failed to create socket: Address family not supported by protocol

dmesg ma całkiem bałagan w logu:

sd 0:0:0:0: [sda] Mode Sense: 38 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI disk
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
eth0: link down
ar71xx: pll_reg 0xb8050014: 0x1a000000
eth0: link up (1000Mbps/Full duplex)
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-04-14
Backport based on wireless-testing.git master-2011-04-19
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (460 buckets, 1840 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
        Hooked IMQ after mangle on PREROUTING
        Hooked IMQ after nat on POSTROUTING
IMQ driver loaded successfully.
Ebtables v2.0 registered
usbcore: registered new interface driver snd-usb-audio
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
usbcore: registered new interface driver hiddev
input: USB  AUDIO   as /devices/platform/ar71xx-ehci/usb1/1-1/1-1.3/1-1.3:1.3/input/input1
generic-usb 0003:1130:F211.0001: input: USB HID v1.10 Device [USB  AUDIO  ] on usb-ar71xx-ehci-1.3/input3
input: USB  AUDIO   as /devices/platform/ar71xx-ehci/usb1/1-1/1-1.3/1-1.3:1.4/input/input2
generic-usb 0003:1130:F211.0002: input: USB HID v1.10 Device [USB  AUDIO  ] on usb-ar71xx-ehci-1.3/input4
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
fuse init (API version 7.13)
lirc_dev: version magic '2.6.32.16 mod_unload MIPS32_R2 32BIT ' should be '2.6.32.27 mod_unload MIPS32_R2 32BIT '
lirc_mceusb2: version magic '2.6.32.16 mod_unload MIPS32_R2 32BIT ' should be '2.6.32.27 mod_unload MIPS32_R2 32BIT '
lirc_dev: version magic '2.6.32.16 mod_unload MIPS32_R2 32BIT ' should be '2.6.32.27 mod_unload MIPS32_R2 32BIT '
Adding 208836k swap on /dev/sda2.  Priority:-1 extents:1 across:208836k
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
device wlan0 entered promiscuous mode
wlan0: authenticate with 74:ea:3a:d1:d1:0e (try 1)
wlan0: authenticated
wlan0: associate with 74:ea:3a:d1:d1:0e (try 1)
wlan0: RX AssocResp from 74:ea:3a:d1:d1:0e (capab=0x431 status=0 aid=2)
wlan0: associated
br-wan: port 1(wlan0) entering forwarding state
ipt_bandwidth: timezone shift detected, adjusting
device tap0 entered promiscuous mode
br-lan: port 2(tap0) entering forwarding state
ath: Failed to stop TX DMA!
ar71xx-wdt: enabling watchdog timer
usb 1-1.2: USB disconnect, address 4
Read-error on swap-device (8:0:1606700)
Read-error on swap-device (8:0:1606708)
Read-error on swap-device (8:0:1606716)
Read-error on swap-device (8:0:1606724)
Read-error on swap-device (8:0:1606732)
Read-error on swap-device (8:0:1606740)
Read-error on swap-device (8:0:1606748)
Read-error on swap-device (8:0:1606756)
usb 1-1: USB disconnect, address 2
usb 1-1.1: USB disconnect, address 3
usb 1-1.3: USB disconnect, address 5
usb 1-1: new high speed USB device using ar71xx-ehci and address 6
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.1: new low speed USB device using ar71xx-ehci and address 7
usb 1-1.1: configuration #1 chosen from 1 choice
usb 1-1.3: new full speed USB device using ar71xx-ehci and address 8
usb 1-1.3: device descriptor read/64, error -32
usb 1-1.3: device descriptor read/64, error -32
usb 1-1.3: new full speed USB device using ar71xx-ehci and address 9
usb 1-1.3: device descriptor read/64, error -32
usb 1-1.3: device descriptor read/64, error -32
usb 1-1.3: new full speed USB device using ar71xx-ehci and address 10
usb 1-1.3: device not accepting address 10, error -32
usb 1-1.3: new full speed USB device using ar71xx-ehci and address 11
usb 1-1.3: device not accepting address 11, error -32
hub 1-1:1.0: unable to enumerate USB device on port 3
usb 1-1.2: new high speed USB device using ar71xx-ehci and address 12
usb 1-1.2: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access     ST925031 5AS                   PQ: 0 ANSI: 4
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
usb-storage: device scan complete
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 38 00 00 00
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sd 1:0:0:0: [sdb] Attached SCSI disk
EXT3-fs error (device sda1): ext3_find_entry: reading directory #14369 offset 0
EXT3-fs error (device sda1): ext3_find_entry: reading directory #28745 offset 0
------------[ cut here ]------------
WARNING: at fs/buffer.c:1159 0x800fe578()
Modules linked in: fuse usbhid sierra option hid ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200 ums_freecom ums_datafab ums_cypress ums_alauda usbserial snd_usb_audio snd_usb_lib evdev ebt_arpnat ebt_redirect ebt_mark ebt_vlan ebt_stp ebt_pkttype ebt_mark_m ebt_limit ebt_among ebt_802_3 ebtable_nat ebtable_filter ebtable_broute ebtables xt_IMQ imq ipt_weburl ipt_webmon ipt_timerange nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp xt_iprange xt_HL xt_hl xt_MARK ipt_ECN xt_CLASSIFY xt_time xt_tcpmss xt_statistic xt_mark xt_length ipt_ecn xt_DSCP xt_dscp xt_string xt_layer7 ipt_bandwidth ipt_REDIRECT ipt_NETMAP ipt_MASQUERADE iptable_nat nf_nat xt_CONNMARK xt_recent xt_helper xt_conntrack xt_connmark xt_connbytes xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack pppoe pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables nfsd nfs msdos tun snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd_page_alloc snd soundcore ppp_async ppp_generic slhc vfat fat lockd sunrpc autofs4 ath9k ath9k_common ath9k_hw ath nls_utf8 nls_koi8_r nls_iso8859_2 nls_iso8859_15 nls_iso8859_13 nls_iso8859_1 nls_cp866 nls_cp852 nls_cp850 nls_cp775 nls_cp437 nls_cp1251 nls_cp1250 mac80211 ts_fsm ts_bm ts_kmp exportfs crc_ccitt cfg80211 compat_firmware_class compat arc4 aes_generic deflate ecb cbc usb_storage ehci_hcd sd_mod ext2 ext3 jbd ext4 jbd2 usbcore scsi_mod nls_base mbcache crc16 leds_gpio button_hotplug gpio_buttons input_polldev input_core
Call Trace:[<80068694>] 0x80068694
[<80068694>] 0x80068694
[<8007d23c>] 0x8007d23c
[<800fe578>] 0x800fe578
[<800ff170>] 0x800ff170
[<800fe578>] 0x800fe578
[<81b0d7a0>] 0x81b0d7a0
[<81b0edf4>] 0x81b0edf4
[<81b0ef08>] 0x81b0ef08
[<81b0b0b8>] 0x81b0b0b8
[<800af3c0>] 0x800af3c0
[<800af488>] 0x800af488
[<81b0bd08>] 0x81b0bd08
[<800e2254>] 0x800e2254
[<800e19b4>] 0x800e19b4
[<800e3880>] 0x800e3880
[<801304c4>] 0x801304c4
[<800ec8f8>] 0x800ec8f8
[<800e2034>] 0x800e2034
[<800e4304>] 0x800e4304
[<800e4d10>] 0x800e4d10
[<800e1d6c>] 0x800e1d6c
[<800e4f28>] 0x800e4f28
[<800e5c34>] 0x800e5c34
[<800c9030>] 0x800c9030
[<800d7304>] 0x800d7304
[<80062544>] 0x80062544

---[ end trace 5cab1471cd24fa46 ]---
EXT3-fs error (device sda1): ext3_find_entry: reading directory #21555 offset 0
EXT3-fs error (device sda1): ext3_find_entry: reading directory #21557 offset 0
EXT3-fs error (device sda1): ext3_find_entry: reading directory #28801 offset 0
EXT3-fs error (device sda1): ext3_find_entry: reading directory #28810 offset 0
EXT3-fs error (device sda1): ext3_find_entry: reading directory #21555 offset 0
Chyba jest to co przypuszczam jak wyżej pisalem brak zasilania na hubie i wywala się system z hdd.
Czy mam racje??

TL-WR1043ND: HDD-USB, extroot, LCD, Pilot, MP3 - Radio Player, NAS, Torrent, FTP, Sterowanie głosem, Komunikaty Głosowe, Termometr, PowerSwitch - Sterownik oświetlenia, Budzik, LTE - ODU IDU 200
Raspberry Pi + HDMI-VGA + Lcd Controller + Lcd z laptopa = Pogodynka