19:47:31 [root@OpenWrt] ~$ dmesg
[    0.000000] Linux version 4.14.143 (cezary@eko.one.pl) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10532-cf3b50377e)) #0 Sat Sep 14 15:10:41 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link Archer C7 v2
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 804f9f30, node_mem_map 81008c20
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from 0x804fd740 with crng_init=0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 123304K/131072K available (4023K kernel code, 160K rwdata, 532K rodata, 1228K init, 211K bss, 7768K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 720.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008295] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.074984] pid_max: default: 32768 minimum: 301
[    0.080063] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.087103] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098247] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108741] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.115286] pinctrl core: initialized pinctrl subsystem
[    0.122707] NET: Registered protocol family 16
[    0.130045] PCI host bridge /ahb/apb/pcie-controller@18250000 ranges:
[    0.136944]  MEM 0x0000000012000000..0x0000000013ffffff
[    0.142499]   IO 0x0000000000000001..0x0000000000000001
[    0.162688] PCI host bridge to bus 0000:00
[    0.167050] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[    0.174395] pci_bus 0000:00: root bus resource [io  0x0001]
[    0.180316] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.187542] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.195998] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[    0.196051] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.196106] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    0.196177] pci 0000:00:00.0: supports D1 D2
[    0.196353] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.196376] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[    0.204191] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[    0.214265] clocksource: Switched to clocksource MIPS
[    0.220477] NET: Registered protocol family 2
[    0.225862] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.233284] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.240090] TCP: Hash tables configured (established 1024 bind 1024)
[    0.246964] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.253187] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.260083] NET: Registered protocol family 1
[    0.264783] PCI: CLS 0 bytes, default 32
[    0.267156] Crashlog allocated RAM at address 0x3f00000
[    0.273738] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.284751] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.290956] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.308877] io scheduler noop registered
[    0.313049] io scheduler deadline registered (default)
[    0.318833] ar7200-usb-phy 18030000.usb-phy0: phy reset is missing
[    0.325490] ar7200-usb-phy 18030010.usb-phy1: phy reset is missing
[    0.333642] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[    0.341580] gpio-export gpio-export: 2 gpio(s) exported
[    0.347915] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.356690] console [ttyS0] disabled
[    0.360523] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.369736] console [ttyS0] enabled
[    0.377156] bootconsole [early0] disabled
[    0.403633] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.408476] 3 fixed-partitions partitions found on MTD device spi0.0
[    0.414937] Creating 3 MTD partitions on "spi0.0":
[    0.419804] 0x000000000000-0x000000020000 : "u-boot"
[    0.425509] 0x000000020000-0x000000ff0000 : "firmware"
[    0.431690] 2 tplink-fw partitions found on MTD device firmware
[    0.437734] Creating 2 MTD partitions on "firmware":
[    0.442773] 0x000000000000-0x0000001854ed : "kernel"
[    0.448434] 0x0000001854f0-0x000000fd0000 : "rootfs"
[    0.454050] mtd: device 3 (rootfs) set to be root filesystem
[    0.459867] 1 squashfs-split partitions found on MTD device rootfs
[    0.466167] 0x000000490000-0x000000fd0000 : "rootfs_data"
[    0.472251] 0x000000ff0000-0x000001000000 : "art"
[    0.478638] libphy: Fixed MDIO Bus: probed
[    0.825981] libphy: ag71xx_mdio: probed
[    0.832498] switch0: Atheros AR8327 rev. 4 switch registered on mdio-bus.0
[    1.483574] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    1.494955] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    1.835850] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[    1.845475] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[    1.853959] NET: Registered protocol family 10
[    1.862946] Segment Routing with IPv6
[    1.866795] NET: Registered protocol family 17
[    1.871346] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.884504] 8021q: 802.1Q VLAN Support v1.8
[    1.890983] hctosys: unable to open rtc device (rtc0)
[    1.900721] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.912319] Freeing unused kernel memory: 1228K
[    1.916944] This architecture does not have kernel memory protection.
[    2.584279] random: fast init done
[    2.608941] init: Console is alive
[    2.612563] init: - watchdog -
[    4.334828] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.493406] usbcore: registered new interface driver usbfs
[    4.499081] usbcore: registered new interface driver hub
[    4.504573] usbcore: registered new device driver usb
[    4.535589] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.548999] SCSI subsystem initialized
[    4.556654] ehci-platform: EHCI generic platform driver
[    4.562166] ehci-platform 1b000000.usb: EHCI Host Controller
[    4.567978] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[    4.576004] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000
[    4.604294] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    4.611224] hub 1-0:1.0: USB hub found
[    4.615378] hub 1-0:1.0: 1 port detected
[    4.619883] ehci-platform 1b400000.usb: EHCI Host Controller
[    4.625697] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[    4.633720] ehci-platform 1b400000.usb: irq 15, io mem 0x1b400000
[    4.664291] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[    4.671238] hub 2-0:1.0: USB hub found
[    4.675364] hub 2-0:1.0: 1 port detected
[    4.683073] usbcore: registered new interface driver usb-storage
[    4.690915] usbcore: registered new interface driver uas
[    4.696856] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.706830] init: - preinit -
[    5.604333] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    5.918416] random: jshn: uninitialized urandom read (4 bytes read)
[    6.000933] random: procd: uninitialized urandom read (4 bytes read)
[    6.007840] usb-storage 1-1:1.0: USB Mass Storage device detected
[    6.025084] scsi host0: usb-storage 1-1:1.0
[    6.184769] random: jshn: uninitialized urandom read (4 bytes read)
[    7.096496] scsi 0:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 4
[    7.470560] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[    7.476589] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[    8.515404] eth1: link up (1000Mbps/Full duplex)
[    8.520109] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[    8.526788] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
[    9.728434] sd 0:0:0:0: [sda] 15133248 512-byte logical blocks: (7.75 GB/7.22 GiB)
[    9.736544] sd 0:0:0:0: [sda] Write Protect is off
[    9.741415] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[    9.741918] sd 0:0:0:0: [sda] No Caching mode page found
[    9.747343] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    9.779419]  sda: sda1
[    9.784802] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   10.645653] mount_root: loading kmods from internal overlay
[   10.677027] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.684943] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   12.041516] jffs2: notice: (533) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (3 unchecked, 4 orphan) and 74 of xref (8 dead, 0 orphan) found.
[   12.057733] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   12.077027] block: extroot: not configured
[   12.292024] jffs2: notice: (531) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (3 unchecked, 4 orphan) and 74 of xref (8 dead, 0 orphan) found.
[   12.312981] mount_root: loading kmods from internal overlay
[   12.500665] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   12.745894] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   16.355705] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   16.368490] block: extroot: not configured
[   16.373621] mount_root: switching to jffs2 overlay
[   16.402181] overlayfs: upper fs does not support tmpfile.
[   16.412765] urandom-seed: Seeding with /etc/urandom.seed
[   16.523530] eth1: link down
[   16.553010] procd: - early -
[   16.556076] procd: - watchdog -
[   17.200931] procd: - watchdog -
[   17.204421] procd: - ubus -
[   17.352768] urandom_read: 5 callbacks suppressed
[   17.352775] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.379184] random: ubusd: uninitialized urandom read (4 bytes read)
[   17.386912] procd: - init -
[   18.699144] kmodloader: loading kernel modules from /etc/modules.d/*
[   18.737731] urngd: v1.0.0 started.
[   18.776955] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[   18.797536] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.830140] Loading modules backported from Linux version v4.19.66-0-g893af1c79e42
[   18.837865] Backport generated by backports.git v4.19.66-1-0-g354501da
[   18.886082] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.921552] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   19.096021] xt_time: kernel timezone is -0000
[   19.108478] random: crng init done
[   19.294556] PPP generic driver version 2.4.2
[   19.301105] NET: Registered protocol family 24
[   19.330539] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x3c.
[   19.339873] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   19.345820] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   19.627949] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
[   19.638658] ath10k_pci 0000:00:00.0: Falling back to user helper
[   19.931689] F2FS-fs (sda1): Mounted with checkpoint version = 3dea1c4d
[   20.313488] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[   20.322679] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[   20.333562] ath10k_pci 0000:00:00.0: Falling back to user helper
[   20.512902] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[   20.523357] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[   20.534507] ath10k_pci 0000:00:00.0: Falling back to user helper
[   20.716257] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[   20.725894] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[   20.737042] ath10k_pci 0000:00:00.0: Falling back to user helper
[   20.916073] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[   20.925693] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[   20.936572] ath10k_pci 0000:00:00.0: Falling back to user helper
[   21.117505] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   21.126868] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[   21.137749] ath10k_pci 0000:00:00.0: Falling back to user helper
[   21.318875] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[   21.328227] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[   21.339112] ath10k_pci 0000:00:00.0: Falling back to user helper
[   21.529419] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[   21.538801] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[   21.549679] ath10k_pci 0000:00:00.0: Falling back to user helper
[   21.729278] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[   21.741623] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   21.751023] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   21.763437] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-fa250764 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 26a1777b
[   21.888295] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   21.898908] ath10k_pci 0000:00:00.0: Falling back to user helper
[   22.004039] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   22.013289] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   22.962189] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   22.978952] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   22.985280] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   22.993403] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 20904 iram: 25992'
[   23.044500] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[   23.058398] ath10k_pci 0000:00:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
[   23.197621] ath: EEPROM regdomain: 0x0
[   23.197628] ath: EEPROM indicates default country code should be used
[   23.197631] ath: doing EEPROM country->regdmn map search
[   23.197644] ath: country maps to regdmn code: 0x3a
[   23.197649] ath: Country alpha2 being used: US
[   23.197652] ath: Regpair used: 0x3a
[   23.263020] ath: EEPROM regdomain: 0x0
[   23.263026] ath: EEPROM indicates default country code should be used
[   23.263030] ath: doing EEPROM country->regdmn map search
[   23.263042] ath: country maps to regdmn code: 0x3a
[   23.263047] ath: Country alpha2 being used: US
[   23.263050] ath: Regpair used: 0x3a
[   23.280587] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   23.282057] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=13
[   23.344640] kmodloader: done loading kernel modules from /etc/modules.d/*
[   33.685915] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   33.692987] eth1: link up (1000Mbps/Full duplex)
[   33.704437] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   33.723232] br-lan: port 1(eth1.1) entered blocking state
[   33.728753] br-lan: port 1(eth1.1) entered disabled state
[   33.734610] device eth1.1 entered promiscuous mode
[   33.739473] device eth1 entered promiscuous mode
[   33.771918] br-lan: port 1(eth1.1) entered blocking state
[   33.777441] br-lan: port 1(eth1.1) entered forwarding state
[   33.783337] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   33.848925] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   33.866582] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   34.754655] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   34.915597] eth0: link up (1000Mbps/Full duplex)
[   34.920348] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.994460] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   36.221142] ath: EEPROM regdomain: 0x8114
[   36.221149] ath: EEPROM indicates we should expect a country code
[   36.221153] ath: doing EEPROM country->regdmn map search
[   36.221157] ath: country maps to regdmn code: 0x37
[   36.221162] ath: Country alpha2 being used: DE
[   36.221166] ath: Regpair used: 0x37
[   36.221171] ath: regdomain 0x8114 dynamically updated by user
[   36.221246] ath: EEPROM regdomain: 0x8114
[   36.221249] ath: EEPROM indicates we should expect a country code
[   36.221253] ath: doing EEPROM country->regdmn map search
[   36.221257] ath: country maps to regdmn code: 0x37
[   36.221260] ath: Country alpha2 being used: DE
[   36.221263] ath: Regpair used: 0x37
[   36.221267] ath: regdomain 0x8114 dynamically updated by user
[   38.871299] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   38.922704] br-lan: port 2(wlan1) entered blocking state
[   38.928209] br-lan: port 2(wlan1) entered disabled state
[   38.933853] device wlan1 entered promiscuous mode
[   38.938747] br-lan: port 2(wlan1) entered blocking state
[   38.944138] br-lan: port 2(wlan1) entered forwarding state
[   38.974391] br-lan: port 2(wlan1) entered disabled state
[   40.784327] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
[   40.802690] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[   40.808829] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
[   40.816971] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 20904 iram: 25992'
[   40.887274] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[   40.909003] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   40.938002] br-lan: port 3(wlan0) entered blocking state
[   40.943393] br-lan: port 3(wlan0) entered disabled state
[   40.949092] device wlan0 entered promiscuous mode
[   41.988095] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   41.994733] br-lan: port 2(wlan1) entered blocking state
[   42.000123] br-lan: port 2(wlan1) entered forwarding state
[   42.064439] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   42.071065] br-lan: port 3(wlan0) entered blocking state
[   42.076494] br-lan: port 3(wlan0) entered forwarding state
[ 2367.256363] device wlan1 left promiscuous mode
[ 2367.260959] br-lan: port 2(wlan1) entered disabled state
[ 2367.918529] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2367.979324] br-lan: port 2(wlan1) entered blocking state
[ 2367.984923] br-lan: port 2(wlan1) entered disabled state
[ 2367.990628] device wlan1 entered promiscuous mode
[ 2367.995479] br-lan: port 2(wlan1) entered blocking state
[ 2368.000901] br-lan: port 2(wlan1) entered forwarding state
[ 2368.286069] br-lan: port 2(wlan1) entered disabled state
[ 2368.338491] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2368.345140] br-lan: port 2(wlan1) entered blocking state
[ 2368.350575] br-lan: port 2(wlan1) entered forwarding state
[ 2397.271255] device wlan1 left promiscuous mode
[ 2397.275908] br-lan: port 2(wlan1) entered disabled state
[ 2397.930059] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2397.990035] br-lan: port 2(wlan1) entered blocking state
[ 2397.995681] br-lan: port 2(wlan1) entered disabled state
[ 2398.001418] device wlan1 entered promiscuous mode
[ 2398.006318] br-lan: port 2(wlan1) entered blocking state
[ 2398.011720] br-lan: port 2(wlan1) entered forwarding state
[ 2398.302902] br-lan: port 2(wlan1) entered disabled state
[ 2398.345401] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2398.351996] br-lan: port 2(wlan1) entered blocking state
[ 2398.357442] br-lan: port 2(wlan1) entered forwarding state
[ 2543.080801] device wlan1 left promiscuous mode
[ 2543.085392] br-lan: port 2(wlan1) entered disabled state
[ 2543.736905] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2543.795224] br-lan: port 2(wlan1) entered blocking state
[ 2543.800664] br-lan: port 2(wlan1) entered disabled state
[ 2543.806385] device wlan1 entered promiscuous mode
[ 2543.811242] br-lan: port 2(wlan1) entered blocking state
[ 2543.816658] br-lan: port 2(wlan1) entered forwarding state
[ 2544.116354] br-lan: port 2(wlan1) entered disabled state
[ 2544.150298] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2544.156939] br-lan: port 2(wlan1) entered blocking state
[ 2544.162327] br-lan: port 2(wlan1) entered forwarding state