Użyłem kompilacji którą udostępniłeś wczoraj, tym razem sysupgrade poszło gładko.
Performing system upgrade...
Unlocking kernel ...
Writing from <stdin> to kernel ... [ ][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w][e][w]
removing ubiblock0_0
[ 582.777924] block ubiblock0_0: released
Volume ID 0, size 45 LEBs (5713920 bytes, 5.4 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 110596096
Volume ID 1, size 871 LEBs (110596096 bytes, 105.4 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 586.378075] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 586.384181] reboot: Restarting system
===================================================================
MT7621 stage1 code 10:33:11 (ASIC)
CPU=50000000 HZ BUS=12500000 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL4 FB_DL: 0xe, 1/0 = 652/372 39000000
PLL2 FB_DL: 0x13, 1/0 = 554/470 4D000000
PLL3 FB_DL: 0x14, 1/0 = 812/212 51000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120
--------------------------------------------------------------------------------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1
000E:| 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
000F:| 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0
0010:| 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
0011:| 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 15
rank 0 fine = 64
B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0
opt_dle value:11
DRAMC_R0DELDLY[018]=00001E1E
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 11 7 9 10 7 8 8 7 6 8
10 | 7 9 9 10 7 11
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =30 DQS1 = 30
==================================================================
bit DQS0 bit DQS1
0 (2~58)30 8 (1~56)28
1 (1~56)28 9 (1~58)29
2 (2~57)29 10 (1~59)30
3 (1~55)28 11 (1~55)28
4 (1~55)28 12 (3~58)30
5 (1~58)29 13 (1~57)29
6 (1~56)28 14 (1~59)30
7 (1~59)30 15 (1~58)29
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 11 9 10 12 9 9 10 7 8 9
10 | 7 11 9 11 7 12
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0082
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1
DQ loop=14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=12500000 HZ
===================================================================
U-Boot 1.1.3 (May 24 2018 - 02:26:51)
Board: Ralink APSoC DRAM: 256 MB
Power on memory test. Memory size= 256 MB...OK!
relocate_code Pointer at: 8ffac000
Config XHCI 40M PLL
******************************
Software System Reset Occurred
******************************
Allocate 16 byte aligned buffer: 8ffe1090
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 42]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
..============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=5 OCP Ratio=1/4
Flash component: NAND Flash
Date:May 24 2018 Time:02:26:51
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LWLLL
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
4 3 2 1 0
Booting System 2
..ranand_erase: start:80000, len:20000
..Done!
done
3: System Boot system code via Flash.
## Booting image at bc600000 ...
Image Name: MIPS OpenWrt Linux-4.14.138
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1870225 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
............................. Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
commandline uart_en=0 factory_mode=0 usb_u3=0
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 4.14.138 (cezary@eko.one.pl) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10196-c4e727f01c)) #0 SMP Thu Aug 22 19:19:04 2019
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3G
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] random: get_random_bytes called from 0x80575744 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26256 r8192 d22896 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00010000
[ 0.000000] Readback ErrCtl register=00010000
[ 0.000000] Memory: 253484K/262144K available (4753K kernel code, 238K rwdata, 584K rodata, 236K init, 254K bss, 8660K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000010] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007816] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073979] pid_max: default: 32768 minimum: 301
[ 0.078752] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085260] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094071] Hierarchical SRCU implementation.
[ 0.099232] smp: Bringing up secondary CPUs ...
[ 0.119488] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.119497] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.119509] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.119651] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.163991] Synchronize counters for CPU 1: done.
[ 0.213613] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.213622] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.213629] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.213703] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.255127] Synchronize counters for CPU 2: done.
[ 0.300643] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.300651] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.300659] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.300739] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.340316] Synchronize counters for CPU 3: done.
[ 0.370178] smp: Brought up 1 node, 4 CPUs
[ 0.378064] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.387857] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.394164] pinctrl core: initialized pinctrl subsystem
[ 0.400828] NET: Registered protocol family 16
[ 0.411296] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.716597] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.721644] ***** Xtal 40MHz *****
[ 0.725002] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.730099] Port 0 N_FTS = 1b105000
[ 0.733570] Port 1 N_FTS = 1b105000
[ 0.737009] Port 2 N_FTS = 1b102800
[ 1.892367] PCIE2 no card, disable it(RST&CLK)
[ 1.896728] -> 21007f2
[ 1.899129] PCIE0 enabled
[ 1.901721] PCIE1 enabled
[ 1.904326] PCI host bridge /pcie@1e140000 ranges:
[ 1.909098] MEM 0x0000000060000000..0x000000006fffffff
[ 1.914259] IO 0x000000001e160000..0x000000001e16ffff
[ 1.919455] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 1.935690] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.941514] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.947364] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.954899] PCI host bridge to bus 0000:00
[ 1.959006] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.965776] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.971665] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.978388] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.988154] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.994667] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.001616] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.008138] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.015082] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.021799] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.028557] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 2.035706] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 2.042465] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 2.049189] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 2.055944] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.060851] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.067620] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.074855] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 2.082030] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.086937] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.093696] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.102198] clocksource: Switched to clocksource GIC
[ 2.108708] NET: Registered protocol family 2
[ 2.113761] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.120646] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.127102] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.133508] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.139268] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.145739] NET: Registered protocol family 1
[ 2.382165] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.388653] Crashlog allocated RAM at address 0x3f00000
[ 2.394141] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 2.407141] random: fast init done
[ 2.411394] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.417169] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.430485] io scheduler noop registered
[ 2.434416] io scheduler deadline registered (default)
[ 2.440576] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.450471] console [ttyS0] disabled
[ 2.454049] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.463067] console [ttyS0] enabled
[ 2.463067] console [ttyS0] enabled
[ 2.469919] bootconsole [early0] disabled
[ 2.469919] bootconsole [early0] disabled
[ 2.478755] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 2.485903] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.493035] Enable NFI Clock
[ 2.495906] # MTK NAND # : Use HW ECC
[ 2.499566] Device not found, ID: c8d1
[ 2.503310] Not Support this Device!
[ 2.507040] chip_mode=00000001
[ 2.510078] Support this Device in MTK table! c8d1
[ 2.515037] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.521495] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 2.527827] nand: ESMT NAND 128MiB 3,3V 8-bit
[ 2.532179] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.539729] Scanning device for bad blocks
[ 2.688886] 10 fixed-partitions partitions found on MTD device MT7621-NAND
[ 2.695741] Creating 10 MTD partitions on "MT7621-NAND":
[ 2.701035] 0x000000000000-0x000000080000 : "Bootloader"
[ 2.707318] 0x000000080000-0x0000000c0000 : "Config"
[ 2.713161] 0x0000000c0000-0x000000100000 : "Bdata"
[ 2.718876] 0x000000100000-0x000000140000 : "Factory"
[ 2.724831] 0x000000140000-0x000000180000 : "crash"
[ 2.730549] 0x000000180000-0x0000001c0000 : "crash_syslog"
[ 2.736943] 0x0000001c0000-0x000000200000 : "reserved0"
[ 2.743120] 0x000000200000-0x000000600000 : "kernel_stock"
[ 2.749485] 0x000000600000-0x000000a00000 : "kernel"
[ 2.755416] 0x000000a00000-0x000007f80000 : "ubi"
[ 2.761946] [mtk_nand] probe successfully!
[ 2.766779] Signature matched and data read!
[ 2.771025] load_fact_bbt success 1023
[ 2.775529] libphy: Fixed MDIO Bus: probed
[ 2.844770] libphy: mdio: probed
[ 4.248352] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.255002] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.265722] NET: Registered protocol family 10
[ 4.271723] Segment Routing with IPv6
[ 4.275512] NET: Registered protocol family 17
[ 4.280009] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.292923] 8021q: 802.1Q VLAN Support v1.8
[ 4.300123] UBI: auto-attach mtd9
[ 4.303512] ubi0: attaching mtd9
[ 5.390322] ubi0: scanning is finished
[ 5.410019] ubi0: attached mtd9 (name "ubi", size 117 MiB)
[ 5.415521] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.422378] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.429132] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.436072] ubi0: good PEBs: 940, bad PEBs: 0, corrupted PEBs: 0
[ 5.442048] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.449250] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1700740608
[ 5.458352] ubi0: available PEBs: 0, total reserved PEBs: 940, PEBs reserved for bad PEB handling: 20
[ 5.467566] ubi0: background thread "ubi_bgt0d" started, PID 395
[ 5.469313] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.479040] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.485991] hctosys: unable to open rtc device (rtc0)
[ 5.491269] usb_vbus: disabling
[ 5.500412] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.508093] Freeing unused kernel memory: 236K
[ 5.512562] This architecture does not have kernel memory protection.
[ 6.065776] init: Console is alive
[ 6.069428] init: - watchdog -
[ 7.261752] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.380685] usbcore: registered new interface driver usbfs
[ 7.386296] usbcore: registered new interface driver hub
[ 7.391748] usbcore: registered new device driver usb
[ 7.420912] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.433691] SCSI subsystem initialized
[ 7.440819] ehci-platform: EHCI generic platform driver
[ 7.451984] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 7.461004] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 7.466368] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 7.482340] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 7.491517] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 7.498305] hub 1-0:1.0: USB hub found
[ 7.502128] hub 1-0:1.0: 2 ports detected
[ 7.506832] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 7.512199] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 7.519664] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 7.526276] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 7.535261] hub 2-0:1.0: USB hub found
[ 7.539077] hub 2-0:1.0: 1 port detected
[ 7.550680] usbcore: registered new interface driver usb-storage
[ 7.558236] usbcore: registered new interface driver uas
[ 7.563856] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.572543] init: - preinit -
[ 8.032578] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
[ 8.069562] random: procd: uninitialized urandom read (4 bytes read)
[ 8.077849] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 8.084493] scsi host0: usb-storage 2-1:1.0
[ 8.505552] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.305374] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 6
[ 9.315455] sd 0:0:0:0: [sda] 30310400 512-byte logical blocks: (15.5 GB/14.5 GiB)
[ 9.323651] sd 0:0:0:0: [sda] Write Protect is off
[ 9.329037] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.343196] sda: sda1
[ 9.348552] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 11.739541] mount_root: loading kmods from internal overlay
[ 11.771846] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.779920] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 12.042990] UBIFS (ubi0:1): default file-system created
[ 12.049714] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 547
[ 12.164058] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 12.171871] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 12.181816] UBIFS (ubi0:1): FS size: 109199360 bytes (104 MiB, 860 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
[ 12.192406] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 12.198993] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 6001D1F2-03D2-41B7-BC09-8C5FB8B3834D, small LPT model
[ 12.211772] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 12.218909] block: unable to load configuration (fstab: Entry not found)
[ 12.225687] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 12.232262] block: unable to load configuration (fstab: Entry not found)
[ 12.239000] block: attempting to load /etc/config/fstab
[ 12.247961] block: unable to load configuration (fstab: Entry not found)
[ 12.254745] block: no usable configuration
[ 12.297320] UBIFS (ubi0:1): un-mount UBI device 0
[ 12.302037] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 12.314322] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 550
[ 12.427082] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 12.434950] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 12.444865] UBIFS (ubi0:1): FS size: 109199360 bytes (104 MiB, 860 LEBs), journal size 5459968 bytes (5 MiB, 43 LEBs)
[ 12.455441] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 12.462028] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 6001D1F2-03D2-41B7-BC09-8C5FB8B3834D, small LPT model
[ 12.674302] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 12.681363] block: unable to load configuration (fstab: Entry not found)
[ 12.688194] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 12.694785] block: unable to load configuration (fstab: Entry not found)
[ 12.701533] block: attempting to load /etc/config/fstab
[ 12.706862] block: unable to load configuration (fstab: Entry not found)
[ 12.713637] block: no usable configuration
[ 12.754321] mount_root: overlay filesystem has not been fully initialized yet
[ 12.761848] mount_root: switching to ubifs overlay
[ 12.799036] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 12.873221] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[ 12.888328] procd: - early -
[ 12.891306] procd: - watchdog -
[ 13.552710] random: jshn: uninitialized urandom read (4 bytes read)
Failed to connect to ubus
[ 13.662448] procd: - watchdog -
[ 13.666050] procd: - ubus -
[ 13.767841] random: jshn: uninitialized urandom read (4 bytes read)
[ 13.805051] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.891196] procd: - init -
Please press Enter to activate this console.
[ 14.329436] urngd: v1.0.0 started.
[ 14.449394] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.468832] tun: Universal TUN/TAP device driver, 1.6
[ 14.483731] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.499801] fuse init (API version 7.26)
[ 14.511786] usbcore: registered new interface driver cdc_acm
[ 14.517540] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 14.522475] random: crng init done
[ 14.527661] usbcore: registered new interface driver cdc_wdm
[ 14.528923] random: 6 urandom warning(s) missed due to ratelimiting
[ 14.536450] Loading modules backported from Linux version v4.19.66-0-g893af1c79e42
[ 14.548525] Backport generated by backports.git v4.19.66-1-0-g354501da
[ 14.557236] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.571864] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 14.672681] usbcore: registered new interface driver usblp
[ 14.685342] usbcore: registered new interface driver usbserial
[ 14.691469] usbcore: registered new interface driver usbserial_generic
[ 14.698249] usbserial: USB Serial support registered for generic
[ 14.709746] wireguard: WireGuard 0.0.20190601 loaded. See www.wireguard.com for information.
[ 14.718262] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 14.742613] xt_time: kernel timezone is -0000
[ 14.748542] usbcore: registered new interface driver cdc_ether
[ 14.756900] usbcore: registered new interface driver cdc_ncm
[ 14.794127] usbcore: registered new interface driver huawei_cdc_ncm
[ 14.847184] bus=0x1, slot = 0x0, irq=0xff
[ 14.851504] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 15.884840] mt7603e 0000:01:00.0: Firmware Version: ap_pcie
[ 15.890415] mt7603e 0000:01:00.0: Build Time: 20160107100755
[ 15.932199] mt7603e 0000:01:00.0: firmware init done
[ 16.121365] bus=0x2, slot = 0x1, irq=0xff
[ 16.125754] mt76x2e 0000:02:00.0: ASIC revision: 76120044
[ 16.848750] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
[ 16.858437] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[ 16.863972] mt76x2e 0000:02:00.0: Build: 1
[ 16.868050] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[ 16.892209] mt76x2e 0000:02:00.0: Firmware running!
[ 16.910885] PPP generic driver version 2.4.2
[ 16.917035] NET: Registered protocol family 24
[ 16.924490] usbcore: registered new interface driver qmi_wwan
[ 16.932493] usbcore: registered new interface driver rndis_host
[ 16.940223] usbcore: registered new interface driver sierra
[ 16.946006] usbserial: USB Serial support registered for Sierra USB modem
[ 16.955413] usbcore: registered new interface driver sierra_net
[ 16.965449] usbcore: registered new interface driver cdc_mbim
[ 16.973057] usbcore: registered new interface driver option
[ 16.978864] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.990228] usbcore: registered new interface driver qcserial
[ 16.996293] usbserial: USB Serial support registered for Qualcomm USB modem
[ 17.003700] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 33.644726] mtk_soc_eth 1e100000.ethernet: PPE started
[ 33.654414] device eth0 entered promiscuous mode
[ 33.659689] br-lan: port 1(eth0.1) entered blocking state
[ 33.665351] br-lan: port 1(eth0.1) entered disabled state
[ 33.671488] device eth0.1 entered promiscuous mode
[ 33.679786] br-lan: port 1(eth0.1) entered blocking state
[ 33.685231] br-lan: port 1(eth0.1) entered forwarding state
[ 33.691501] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 34.642945] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
