[    0.000000] Linux version 4.9.120 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9) ) #0 SMP Thu Aug 16 07:51:15 2018
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is TP-LINK TD-W8970
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 80542640, node_mem_map 810091a0
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] percpu: Embedded 12 pages/cpu @8108c000 s17488 r8192 d23472 u49152
[    0.000000] pcpu-alloc: s17488 r8192 d23472 u49152 alloc=12*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyLTQ0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00070980
[    0.000000] Readback ErrCtl register=00070980
[    0.000000] Memory: 57884K/65536K available (4305K kernel code, 173K rwdata, 900K rodata, 1260K init, 244K bss, 7652K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] Setting up IPI vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007886] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042381] pid_max: default: 32768 minimum: 301
[    0.047263] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053797] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.065860] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.065873] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.066075] CPU1 revision is: 00019556 (MIPS 34Kc)
[    0.116518] Synchronize counters for CPU 1:
[    0.116520] done.
[    0.123028] Brought up 2 CPUs
[    0.130719] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.140384] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.146619] pinctrl core: initialized pinctrl subsystem
[    0.153170] NET: Registered protocol family 16
[    0.166724] pinctrl-xway 1e100b10.pinmux: Init done
[    0.172754] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.286136] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.291955] Can't analyze schedule() prologue at 8043158c
[    0.426069] PCI host bridge /fpi@10000000/pcie@d900000 ranges:
[    0.460292] usbcore: registered new interface driver usbfs
[    0.465863] usbcore: registered new interface driver hub
[    0.471292] usbcore: registered new device driver usb
[    0.476988] PCI host bridge to bus 0000:00
[    0.481016] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.487923] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.492609] random: fast init done
[    0.498325] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.505219] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.513272] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060000
[    0.513295] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.531140] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.532013] pci 0000:01:00.0: [168c:abcd] type 00 class 0x020000
[    0.532120] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit]
[    0.532234] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    0.532431] pci 0000:01:00.0: supports D1
[    0.532449] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[    0.532807] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.532861] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.532958] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.539726] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref]
[    0.547023] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit]
[    0.554414] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref]
[    0.561672] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.566691] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.573557] pci 0000:00:00.0:   bridge window [mem 0x1c100000-0x1c1fffff pref]
[    0.580880] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[    0.587523] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.593894] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.600519] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.609421] clocksource: Switched to clocksource MIPS
[    0.617047] NET: Registered protocol family 2
[    0.622568] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.629501] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.635876] TCP: Hash tables configured (established 1024 bind 1024)
[    0.642417] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.648202] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.654847] NET: Registered protocol family 1
[    0.659198] PCI: CLS 0 bytes, default 32
[    0.660053] gptu: totally 6 16-bit timers/counters
[    0.665079] gptu: misc_register on minor 63
[    0.669312] gptu: succeeded to request irq 126
[    0.673729] gptu: succeeded to request irq 127
[    0.678230] gptu: succeeded to request irq 128
[    0.682767] gptu: succeeded to request irq 129
[    0.687272] gptu: succeeded to request irq 130
[    0.691800] gptu: succeeded to request irq 131
[    0.696697] phy-xrx200 gphy-xrx200: requesting lantiq/xrx200_phy11g_a22.bin
[    0.704440] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3A40000
[    0.710810] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3A40000
[    0.818363] No VPEs reserved for AP/SP, not initialize VPE loader
[    0.818363] Pass maxvpes=<n> argument as kernel argument
[    0.829748] No TCs reserved for AP/SP, not initializing RTLX.
[    0.829748] Pass maxtcs=<n> argument as kernel argument
[    0.842611] Crashlog allocated RAM at address 0x3f00000
[    0.848480] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.872062] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.877802] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.893518] io scheduler noop registered
[    0.897346] io scheduler deadline registered (default)
[    0.903865] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.912803] console [ttyLTQ0] enabled
[    0.920119] bootconsole [early0] disabled
[    0.931736] spi-lantiq-ssc 1e100800.spi: Lantiq SSC SPI controller (Rev 8, TXFS 8, RXFS 8, DMA 1)
[    0.953041] m25p80 spi32766.4: s25fl064k (8192 Kbytes)
[    0.956848] 4 fixed-partitions partitions found on MTD device spi32766.4
[    0.963473] Creating 4 MTD partitions on "spi32766.4":
[    0.968638] 0x000000000000-0x000000020000 : "u-boot"
[    0.975981] 0x000000020000-0x0000007c0000 : "firmware"
[    1.284499] random: crng init done
[    1.811148] 2 tplink-fw partitions found on MTD device firmware
[    1.815683] 0x000000020000-0x0000001c8de8 : "kernel"
[    1.822942] 0x0000001c8de8-0x0000007c0000 : "rootfs"
[    1.828774] mtd: device 3 (rootfs) set to be root filesystem
[    1.833463] 1 squashfs-split partitions found on MTD device rootfs
[    1.839257] 0x0000004f0000-0x0000007c0000 : "rootfs_data"
[    1.847008] 0x0000007c0000-0x0000007d0000 : "config"
[    1.852859] 0x0000007d0000-0x000000800000 : "boardconfig"
[    1.862895] libphy: Fixed MDIO Bus: probed
[    1.970448] libphy: lantiq,xrx200-mdio: probed
[    2.049899] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4] (mii_bus:phy_addr=0:00, irq=-1)
[    2.133876] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4] (mii_bus:phy_addr=0:05, irq=-1)
[    2.217861] Intel XWAY PHY11G (xRX v1.2 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:11, irq=-1)
[    2.301858] Intel XWAY PHY11G (xRX v1.2 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:13, irq=-1)
[    2.417473] ltq-cputemp cputemp@0: Current CPU die temperature: 54.0 °C
[    2.423175] wdt 1f8803f0.watchdog: Init done
[    2.431990] NET: Registered protocol family 10
[    2.437451] NET: Registered protocol family 17
[    2.440550] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.453474] 8021q: 802.1Q VLAN Support v1.8
[    2.468141] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    2.478269] Freeing unused kernel memory: 1260K
[    2.481402] This architecture does not have kernel memory protection.
[    3.285603] init: Console is alive
[    3.287917] init: - watchdog -
[    4.218455] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[    4.659669] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.817011] dwc2 1e101000.ifxhcd: requested GPIO 495
[    4.921728] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    4.925428] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    4.932672] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    4.938190] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.945619] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    4.953523] hub 1-0:1.0: USB hub found
[    4.955960] hub 1-0:1.0: 1 port detected
[    5.061460] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    5.065069] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    5.072389] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    5.077905] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.085342] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    5.093290] hub 2-0:1.0: USB hub found
[    5.095771] hub 2-0:1.0: 1 port detected
[    5.101469] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.117890] init: - preinit -
[    5.508786] usb 1-1: new high-speed USB device number 2 using dwc2
[    9.492731] jffs2: notice: (437) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    9.541324] mount_root: loading kmods from internal overlay
[    9.881113] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   10.172779] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   10.258376] SCSI subsystem initialized
[   10.286270] ehci-platform: EHCI generic platform driver
[   10.309459] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   10.315459] ohci-platform: OHCI generic platform driver
[   10.350676] usb-storage 1-1:1.0: USB Mass Storage device detected
[   10.356352] scsi host0: usb-storage 1-1:1.0
[   10.360750] usbcore: registered new interface driver usb-storage
[   10.366172] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   10.718010] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   10.732405] block: extroot: device not present, retrying in 5 seconds
[   11.400085] scsi 0:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 4
[   14.434195] sd 0:0:0:0: [sda] 15133248 512-byte logical blocks: (7.75 GB/7.22 GiB)
[   14.440956] sd 0:0:0:0: [sda] Write Protect is off
[   14.445266] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[   14.446113] sd 0:0:0:0: [sda] No Caching mode page found
[   14.450525] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   14.482759]  sda: sda1
[   14.487559] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   16.435274] block: check_filesystem: /usr/sbin/fsck.f2fs not found
[   17.007691] mount_root: switched to extroot
[   17.017047] urandom-seed: Seeding with /etc/urandom.seed
[   17.174623] procd: - early -
[   17.176244] procd: - watchdog -
[   17.457436] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[   17.866776] procd: - watchdog -
[   17.868945] procd: - ubus -
[   20.219268] procd: - init -
[   21.726920] kmodloader: loading kernel modules from /etc/modules.d/*
[   21.739261] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   21.755842] NET: Registered protocol family 8
[   21.758892] NET: Registered protocol family 20
[   21.777456] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[   21.792315] PPP generic driver version 2.4.2
[   21.808737] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   21.838571] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   21.932149] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
[   21.955859] i2c /dev entries driver
[   21.966652]
[   21.966652]
[   21.966652] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   21.974362]
[   21.974362] Predefined debug level: 3
[   21.992335] Linux video capture interface: v2.00
[   22.012694] fuse init (API version 7.26)
[   22.022748] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   22.029398] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   22.039919] ip_tables: (C) 2000-2006 Netfilter Core Team
[   22.049393] Infineon Technologies DEU driver version 2.0.0
[   22.055853] IFX DEU DES initialized (multiblock).
[   22.060774] IFX DEU AES initialized (multiblock).
[   22.064782] IFX DEU ARC4 initialized (multiblock).
[   22.069203] IFX DEU SHA1 initialized.
[   22.072811] IFX DEU MD5 initialized.
[   22.076431] IFX DEU SHA1_HMAC initialized.
[   22.080531] IFX DEU MD5_HMAC initialized.
[   22.142487] NET: Registered protocol family 24
[   22.168603] xt_time: kernel timezone is -0000
[   22.243711] usbcore: registered new interface driver uvcvideo
[   22.248090] USB Video Class driver (1.1.1)
[   22.288432] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   22.292818] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   23.731714] ath: phy0: disabling 5GHz band
[   23.735644] ath: EEPROM regdomain: 0x0
[   23.735689] ath: EEPROM indicates default country code should be used
[   23.735698] ath: doing EEPROM country->regdmn map search
[   23.735717] ath: country maps to regdmn code: 0x3a
[   23.735728] ath: Country alpha2 being used: US
[   23.735736] ath: Regpair used: 0x3a
[   23.749040] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   23.755790] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xbc000000, irq=144
[   23.764098] kmodloader: done loading kernel modules from /etc/modules.d/*
[   32.096584] jffs2: notice: (1130) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   36.182542] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   36.198589] br-lan: port 1(eth0.1) entered blocking state
[   36.202742] br-lan: port 1(eth0.1) entered disabled state
[   36.209305] device eth0.1 entered promiscuous mode
[   36.212798] device eth0 entered promiscuous mode
[   36.224562] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   38.225652] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[   38.230902] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   38.249948] br-lan: port 1(eth0.1) entered blocking state
[   38.254040] br-lan: port 1(eth0.1) entered forwarding state
[   38.421777] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   41.042669] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   41.110031] br-lan: port 2(wlan0) entered blocking state
[   41.113992] br-lan: port 2(wlan0) entered disabled state
[   41.145631] device wlan0 entered promiscuous mode
[   43.184672] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   43.190100] br-lan: port 2(wlan0) entered blocking state
[   43.195022] br-lan: port 2(wlan0) entered forwarding state
[  231.516867] br-lan: port 2(wlan0) entered disabled state
[  231.521193] br-lan: port 1(eth0.1) entered disabled state
[  231.561794] device eth0.1 left promiscuous mode
[  231.564932] device eth0 left promiscuous mode
[  231.569737] br-lan: port 1(eth0.1) entered disabled state
[  231.614209] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[  231.656128] device wlan0 left promiscuous mode
[  231.659456] br-lan: port 2(wlan0) entered disabled state
[  231.889328] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[  239.849501] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  239.864278] br-lan: port 1(eth0.1) entered blocking state
[  239.868347] br-lan: port 1(eth0.1) entered disabled state
[  239.874701] device eth0.1 entered promiscuous mode
[  239.878511] device eth0 entered promiscuous mode
[  239.889209] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  241.905409] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[  241.912078] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  241.927267] br-lan: port 1(eth0.1) entered blocking state
[  241.931364] br-lan: port 1(eth0.1) entered forwarding state
[  241.969148] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  244.093231] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  244.173996] br-lan: port 2(wlan0) entered blocking state
[  244.178049] br-lan: port 2(wlan0) entered disabled state
[  244.184435] device wlan0 entered promiscuous mode
[  245.979567] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  245.985226] br-lan: port 2(wlan0) entered blocking state
[  245.989911] br-lan: port 2(wlan0) entered forwarding state
[ 3831.494370] br-lan: port 2(wlan0) entered disabled state
[ 3831.498608] br-lan: port 1(eth0.1) entered disabled state
[ 3831.567064] device eth0.1 left promiscuous mode
[ 3831.570158] device eth0 left promiscuous mode
[ 3831.574883] br-lan: port 1(eth0.1) entered disabled state
[ 3831.619378] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 3831.658831] device wlan0 left promiscuous mode
[ 3831.662066] br-lan: port 2(wlan0) entered disabled state
[ 3832.046649] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[ 3837.998881] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3838.015790] br-lan: port 1(eth0.1) entered blocking state
[ 3838.019973] br-lan: port 1(eth0.1) entered disabled state
[ 3838.026375] device eth0.1 entered promiscuous mode
[ 3838.029957] device eth0 entered promiscuous mode
[ 3838.042071] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 3840.046975] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[ 3840.052102] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3840.074699] br-lan: port 1(eth0.1) entered blocking state
[ 3840.078860] br-lan: port 1(eth0.1) entered forwarding state
[ 3840.101623] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 3841.147965] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3841.256652] br-lan: port 2(wlan0) entered blocking state
[ 3841.260712] br-lan: port 2(wlan0) entered disabled state
[ 3841.267033] device wlan0 entered promiscuous mode
[ 3844.193865] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3844.199431] br-lan: port 2(wlan0) entered blocking state
[ 3844.204286] br-lan: port 2(wlan0) entered forwarding state
[ 7431.525201] br-lan: port 2(wlan0) entered disabled state
[ 7431.529435] br-lan: port 1(eth0.1) entered disabled state
[ 7431.575966] device eth0.1 left promiscuous mode
[ 7431.579292] device eth0 left promiscuous mode
[ 7431.584032] br-lan: port 1(eth0.1) entered disabled state
[ 7431.628379] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 7431.679670] device wlan0 left promiscuous mode
[ 7431.683046] br-lan: port 2(wlan0) entered disabled state
[ 7432.236938] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[ 7438.007426] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7438.023905] br-lan: port 1(eth0.1) entered blocking state
[ 7438.028026] br-lan: port 1(eth0.1) entered disabled state
[ 7438.034255] device eth0.1 entered promiscuous mode
[ 7438.038199] device eth0 entered promiscuous mode
[ 7438.049366] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 7440.045259] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[ 7440.050231] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7440.080977] br-lan: port 1(eth0.1) entered blocking state
[ 7440.085035] br-lan: port 1(eth0.1) entered forwarding state
[ 7440.112894] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 7441.241125] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 7441.359874] br-lan: port 2(wlan0) entered blocking state
[ 7441.363922] br-lan: port 2(wlan0) entered disabled state
[ 7441.370145] device wlan0 entered promiscuous mode
[ 7443.966853] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 7443.972342] br-lan: port 2(wlan0) entered blocking state
[ 7443.977287] br-lan: port 2(wlan0) entered forwarding state
[11031.571222] br-lan: port 2(wlan0) entered disabled state
[11031.575382] br-lan: port 1(eth0.1) entered disabled state
[11031.637352] device eth0.1 left promiscuous mode
[11031.640470] device eth0 left promiscuous mode
[11031.645435] br-lan: port 1(eth0.1) entered disabled state
[11031.686567] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[11031.731775] device wlan0 left promiscuous mode
[11031.735108] br-lan: port 2(wlan0) entered disabled state
[11032.240728] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[11037.650688] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[11037.666971] br-lan: port 1(eth0.1) entered blocking state
[11037.671106] br-lan: port 1(eth0.1) entered disabled state
[11037.677480] device eth0.1 entered promiscuous mode
[11037.681161] device eth0 entered promiscuous mode
[11037.692175] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[11039.693482] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[11039.698519] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[11039.721346] br-lan: port 1(eth0.1) entered blocking state
[11039.725411] br-lan: port 1(eth0.1) entered forwarding state
[11039.761241] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[11040.913456] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[11041.009329] br-lan: port 2(wlan0) entered blocking state
[11041.013415] br-lan: port 2(wlan0) entered disabled state
[11041.019677] device wlan0 entered promiscuous mode
[11043.855988] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[11043.861756] br-lan: port 2(wlan0) entered blocking state
[11043.866329] br-lan: port 2(wlan0) entered forwarding state
[14631.607962] br-lan: port 2(wlan0) entered disabled state
[14631.612329] br-lan: port 1(eth0.1) entered disabled state
[14631.668144] device eth0.1 left promiscuous mode
[14631.671433] device eth0 left promiscuous mode
[14631.676154] br-lan: port 1(eth0.1) entered disabled state
[14631.715394] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[14631.772181] device wlan0 left promiscuous mode
[14631.775785] br-lan: port 2(wlan0) entered disabled state
[14631.883046] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[14638.012207] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[14638.028235] br-lan: port 1(eth0.1) entered blocking state
[14638.032417] br-lan: port 1(eth0.1) entered disabled state
[14638.038611] device eth0.1 entered promiscuous mode
[14638.042475] device eth0 entered promiscuous mode
[14638.053078] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[14640.043331] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[14640.048301] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[14640.079097] br-lan: port 1(eth0.1) entered blocking state
[14640.083149] br-lan: port 1(eth0.1) entered forwarding state
[14640.119092] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[14641.223907] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[14641.282250] br-lan: port 2(wlan0) entered blocking state
[14641.286294] br-lan: port 2(wlan0) entered disabled state
[14641.292459] device wlan0 entered promiscuous mode
[14644.041044] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[14644.046534] br-lan: port 2(wlan0) entered blocking state
[14644.051400] br-lan: port 2(wlan0) entered forwarding state
[18231.645862] br-lan: port 2(wlan0) entered disabled state
[18231.650097] br-lan: port 1(eth0.1) entered disabled state
[18231.697184] device eth0.1 left promiscuous mode
[18231.700484] device eth0 left promiscuous mode
[18231.705016] br-lan: port 1(eth0.1) entered disabled state
[18231.739182] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[18231.795497] device wlan0 left promiscuous mode
[18231.798889] br-lan: port 2(wlan0) entered disabled state
[18232.232812] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[18238.257877] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[18238.274247] br-lan: port 1(eth0.1) entered blocking state
[18238.278446] br-lan: port 1(eth0.1) entered disabled state
[18238.284917] device eth0.1 entered promiscuous mode
[18238.288434] device eth0 entered promiscuous mode
[18238.298709] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[18240.296976] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[18240.302105] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[18240.340672] br-lan: port 1(eth0.1) entered blocking state
[18240.344781] br-lan: port 1(eth0.1) entered forwarding state
[18240.388793] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[18241.678905] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[18241.776291] br-lan: port 2(wlan0) entered blocking state
[18241.780285] br-lan: port 2(wlan0) entered disabled state
[18241.786598] device wlan0 entered promiscuous mode
[18244.499985] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[18244.505467] br-lan: port 2(wlan0) entered blocking state
[18244.510361] br-lan: port 2(wlan0) entered forwarding state
[21831.689354] br-lan: port 2(wlan0) entered disabled state
[21831.693501] br-lan: port 1(eth0.1) entered disabled state
[21831.743065] device eth0.1 left promiscuous mode
[21831.746162] device eth0 left promiscuous mode
[21831.750966] br-lan: port 1(eth0.1) entered disabled state
[21831.787268] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[21831.830883] device wlan0 left promiscuous mode
[21831.834136] br-lan: port 2(wlan0) entered disabled state
[21832.486669] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[21837.851517] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[21837.868171] br-lan: port 1(eth0.1) entered blocking state
[21837.872306] br-lan: port 1(eth0.1) entered disabled state
[21837.878730] device eth0.1 entered promiscuous mode
[21837.882356] device eth0 entered promiscuous mode
[21837.893731] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[21839.910944] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[21839.915977] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[21839.945687] br-lan: port 1(eth0.1) entered blocking state
[21839.949788] br-lan: port 1(eth0.1) entered forwarding state
[21840.004796] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[21841.299874] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[21841.322641] br-lan: port 2(wlan0) entered blocking state
[21841.326655] br-lan: port 2(wlan0) entered disabled state
[21841.332930] device wlan0 entered promiscuous mode
[21844.164234] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[21844.169981] br-lan: port 2(wlan0) entered blocking state
[21844.174599] br-lan: port 2(wlan0) entered forwarding state
[25430.710978] br-lan: port 2(wlan0) entered disabled state
[25430.715345] br-lan: port 1(eth0.1) entered disabled state
[25430.754169] device eth0.1 left promiscuous mode
[25430.757449] device eth0 left promiscuous mode
[25430.762051] br-lan: port 1(eth0.1) entered disabled state
[25430.798336] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[25430.841392] device wlan0 left promiscuous mode
[25430.845166] br-lan: port 2(wlan0) entered disabled state
[25431.075399] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[25437.161170] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[25437.178846] br-lan: port 1(eth0.1) entered blocking state
[25437.183035] br-lan: port 1(eth0.1) entered disabled state
[25437.189402] device eth0.1 entered promiscuous mode
[25437.193147] device eth0 entered promiscuous mode
[25437.205297] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[25439.203688] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[25439.208706] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[25439.240099] br-lan: port 1(eth0.1) entered blocking state
[25439.244231] br-lan: port 1(eth0.1) entered forwarding state
[25439.299358] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[25440.256224] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[25440.348424] br-lan: port 2(wlan0) entered blocking state
[25440.352412] br-lan: port 2(wlan0) entered disabled state
[25440.358634] device wlan0 entered promiscuous mode
[25442.983087] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[25442.988765] br-lan: port 2(wlan0) entered blocking state
[25442.993551] br-lan: port 2(wlan0) entered forwarding state
[28620.802506] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[29030.757475] br-lan: port 2(wlan0) entered disabled state
[29030.761671] br-lan: port 1(eth0.1) entered disabled state
[29030.786981] device eth0.1 left promiscuous mode
[29030.790169] device eth0 left promiscuous mode
[29030.794817] br-lan: port 1(eth0.1) entered disabled state
[29030.819100] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[29030.858205] device wlan0 left promiscuous mode
[29030.861471] br-lan: port 2(wlan0) entered disabled state
[29031.426297] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[29031.431176] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[29037.269581] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[29037.284807] br-lan: port 1(eth0.1) entered blocking state
[29037.288869] br-lan: port 1(eth0.1) entered disabled state
[29037.295207] device eth0.1 entered promiscuous mode
[29037.299112] device eth0 entered promiscuous mode
[29037.309094] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[29039.330726] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[29039.335627] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[29039.370999] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[29039.394408] br-lan: port 1(eth0.1) entered blocking state
[29039.398458] br-lan: port 1(eth0.1) entered forwarding state
[29039.429437] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[29040.262024] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[29040.367263] br-lan: port 2(wlan0) entered blocking state
[29040.371261] br-lan: port 2(wlan0) entered disabled state
[29040.377799] device wlan0 entered promiscuous mode
[29040.381631] br-lan: port 2(wlan0) entered blocking state
[29040.386560] br-lan: port 2(wlan0) entered forwarding state
[29040.402647] br-lan: port 2(wlan0) entered disabled state
[29043.232994] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[29043.238526] br-lan: port 2(wlan0) entered blocking state
[29043.243337] br-lan: port 2(wlan0) entered forwarding state
[32630.802843] br-lan: port 2(wlan0) entered disabled state
[32630.807071] br-lan: port 1(eth0.1) entered disabled state
[32630.870407] device eth0.1 left promiscuous mode
[32630.873634] device eth0 left promiscuous mode
[32630.878305] br-lan: port 1(eth0.1) entered disabled state
[32630.909509] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[32630.950476] device wlan0 left promiscuous mode
[32630.953948] br-lan: port 2(wlan0) entered disabled state
[32631.521969] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[32631.526831] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[32637.252267] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[32637.269059] br-lan: port 1(eth0.1) entered blocking state
[32637.273329] br-lan: port 1(eth0.1) entered disabled state
[32637.279706] device eth0.1 entered promiscuous mode
[32637.283344] device eth0 entered promiscuous mode
[32637.295680] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[32639.298260] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[32639.304063] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[32639.322116] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[32639.354036] br-lan: port 1(eth0.1) entered blocking state
[32639.358109] br-lan: port 1(eth0.1) entered forwarding state
[32639.394713] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[32640.431036] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[32640.522910] br-lan: port 2(wlan0) entered blocking state
[32640.526907] br-lan: port 2(wlan0) entered disabled state
[32640.533151] device wlan0 entered promiscuous mode
[32643.481756] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[32643.487303] br-lan: port 2(wlan0) entered blocking state
[32643.492230] br-lan: port 2(wlan0) entered forwarding state
[36230.838530] br-lan: port 2(wlan0) entered disabled state
[36230.842785] br-lan: port 1(eth0.1) entered disabled state
[36230.922951] device eth0.1 left promiscuous mode
[36230.926150] device eth0 left promiscuous mode
[36230.930949] br-lan: port 1(eth0.1) entered disabled state
[36230.958603] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[36230.988487] device wlan0 left promiscuous mode
[36230.992009] br-lan: port 2(wlan0) entered disabled state
[36231.522223] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[36231.527355] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[36237.265493] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[36237.281014] br-lan: port 1(eth0.1) entered blocking state
[36237.285064] br-lan: port 1(eth0.1) entered disabled state
[36237.291458] device eth0.1 entered promiscuous mode
[36237.295235] device eth0 entered promiscuous mode
[36237.305605] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[36239.298644] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[36239.303568] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[36239.318288] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[36239.341435] br-lan: port 1(eth0.1) entered blocking state
[36239.345495] br-lan: port 1(eth0.1) entered forwarding state
[36239.374175] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[36240.299025] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[36240.392280] br-lan: port 2(wlan0) entered blocking state
[36240.396319] br-lan: port 2(wlan0) entered disabled state
[36240.402824] device wlan0 entered promiscuous mode
[36243.326123] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[36243.331574] br-lan: port 2(wlan0) entered blocking state
[36243.336515] br-lan: port 2(wlan0) entered forwarding state
[39830.886037] br-lan: port 2(wlan0) entered disabled state
[39830.890311] br-lan: port 1(eth0.1) entered disabled state
[39830.950981] device eth0.1 left promiscuous mode
[39830.954258] device eth0 left promiscuous mode
[39830.959061] br-lan: port 1(eth0.1) entered disabled state
[39830.984702] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[39831.036571] device wlan0 left promiscuous mode
[39831.039980] br-lan: port 2(wlan0) entered disabled state
[39831.490147] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[39831.495026] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[39837.305352] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[39837.320825] br-lan: port 1(eth0.1) entered blocking state
[39837.325017] br-lan: port 1(eth0.1) entered disabled state
[39837.331166] device eth0.1 entered promiscuous mode
[39837.335043] device eth0 entered promiscuous mode
[39837.345485] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[39839.362412] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[39839.367327] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[39839.386219] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[39839.413335] br-lan: port 1(eth0.1) entered blocking state
[39839.417393] br-lan: port 1(eth0.1) entered forwarding state
[39839.447343] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[39840.339180] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[39840.416992] br-lan: port 2(wlan0) entered blocking state
[39840.421015] br-lan: port 2(wlan0) entered disabled state
[39840.427189] device wlan0 entered promiscuous mode
[39843.305019] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[39843.310497] br-lan: port 2(wlan0) entered blocking state
[39843.315380] br-lan: port 2(wlan0) entered forwarding state
[43430.920890] br-lan: port 2(wlan0) entered disabled state
[43430.925155] br-lan: port 1(eth0.1) entered disabled state
[43430.972885] device eth0.1 left promiscuous mode
[43430.976115] device eth0 left promiscuous mode
[43430.980769] br-lan: port 1(eth0.1) entered disabled state
[43431.012210] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[43431.066066] device wlan0 left promiscuous mode
[43431.069452] br-lan: port 2(wlan0) entered disabled state
[43431.615942] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[43431.620738] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[43437.504817] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[43437.520894] br-lan: port 1(eth0.1) entered blocking state
[43437.525043] br-lan: port 1(eth0.1) entered disabled state
[43437.531330] device eth0.1 entered promiscuous mode
[43437.535195] device eth0 entered promiscuous mode
[43437.545778] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[43439.616190] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[43439.621109] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[43439.660166] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[43439.681348] br-lan: port 1(eth0.1) entered blocking state
[43439.685503] br-lan: port 1(eth0.1) entered forwarding state
[43439.723890] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[43441.388797] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[43441.490390] br-lan: port 2(wlan0) entered blocking state
[43441.494392] br-lan: port 2(wlan0) entered disabled state
[43441.500657] device wlan0 entered promiscuous mode
[43444.350545] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[43444.356227] br-lan: port 2(wlan0) entered blocking state
[43444.360863] br-lan: port 2(wlan0) entered forwarding state
[47030.958704] br-lan: port 2(wlan0) entered disabled state
[47030.963022] br-lan: port 1(eth0.1) entered disabled state
[47031.020759] device eth0.1 left promiscuous mode
[47031.024017] device eth0 left promiscuous mode
[47031.028681] br-lan: port 1(eth0.1) entered disabled state
[47031.052964] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[47031.094446] device wlan0 left promiscuous mode
[47031.097907] br-lan: port 2(wlan0) entered disabled state
[47031.871753] lantiq,xrx200-net 1e108000.eth eth0: port 5 lost link
[47031.876707] lantiq,xrx200-net 1e108000.eth eth0: port 2 lost link
[47037.643351] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[47037.659344] br-lan: port 1(eth0.1) entered blocking state
[47037.663441] br-lan: port 1(eth0.1) entered disabled state
[47037.669744] device eth0.1 entered promiscuous mode
[47037.673588] device eth0 entered promiscuous mode
[47037.685867] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[47039.680043] lantiq,xrx200-net 1e108000.eth eth0: port 5 got link
[47039.684963] lantiq,xrx200-net 1e108000.eth eth0: port 2 got link
[47039.707920] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[47039.729045] br-lan: port 1(eth0.1) entered blocking state
[47039.733099] br-lan: port 1(eth0.1) entered forwarding state
[47039.765989] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[47041.060950] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[47041.150900] br-lan: port 2(wlan0) entered blocking state
[47041.154906] br-lan: port 2(wlan0) entered disabled state
[47041.161091] device wlan0 entered promiscuous mode
[47043.966033] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[47043.971557] br-lan: port 2(wlan0) entered blocking state
[47043.976422] br-lan: port 2(wlan0) entered forwarding state