Temat: Flash upgrade - Ralink A5-V11
Postanowiłem zrobić upgrade kości Flash w mini routerze A5-V11 z 4MB do 16MB.
Genrlanei cały proces się powiódł, ale obecnie nie działa mi Wifi.
Pamietam, że w Tp-Linkach była partycja ART którą trzeba było wgrać na mową kość. Tutja nie widzę niczego takiego.
Przed upgradem:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 00030000 00001000 "u-boot"
mtd1: 00010000 00001000 "u-boot-env"
mtd2: 00010000 00001000 "factory"
mtd3: 003b0000 00001000 "firmware"
mtd4: 0014e82b 00001000 "kernel"
mtd5: 002617d5 00001000 "rootfs"
mtd6: 00031000 00001000 "rootfs_data"Po:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 00030000 00001000 "u-boot"
mtd1: 00010000 00001000 "u-boot-env"
mtd2: 00010000 00001000 "factory"
mtd3: 00fb0000 00001000 "firmware"
mtd4: 00159015 00001000 "kernel"
mtd5: 00e56feb 00001000 "rootfs"
mtd6: 00c7d000 00001000 "rootfs_data"Ale po kolej co zrobiłem:
Wgrałem na nową kość pamięci u-boot znaleziony: https://oldwiki.archive.openwrt.org/toh … ded/a5-v11
Później z poziomu bootloader z USB wgrałem firmware pobrany stąd:
https://downloads.openwrt.org/releases/ … ps/rt305x/
Log z TTL:
- Przed
U-Boot 1.1.3 (Apr 11 2013 - 00:10:51)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb4000
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 42
spi device id: 7f 9d 46 7f 9d (9d467f9d)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
.*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.6.0.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:Apr 11 2013 Time:00:10:51
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ ####
estimate memory size =32 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
. Image Name: MIPS OpenWrt Linux-4.14.63
Created: 2018-08-16 7:51:15 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1370091 Bytes = 1.3 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:14e7eb
..................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
[ 0.000000] Linux version 4.14.63 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7102-3f3a2c9)) #0 Th
u Aug 16 07:51:15 2018
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is A5-V11
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] random: get_random_bytes called from 0x803ee72c with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=0000ad60
[ 0.000000] Readback ErrCtl register=0000ad60
[ 0.000000] Memory: 27960K/32768K available (3419K kernel code, 172K rwdata, 424K rodata, 200K init, 210K bss, 4808K reserved, 0K cma-res
erved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 10618113593 ns
[ 0.000016] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
[ 0.015713] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.098021] pid_max: default: 32768 minimum: 301
[ 0.107600] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.120714] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.143473] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.163028] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.175291] pinctrl core: initialized pinctrl subsystem
[ 0.188503] NET: Registered protocol family 16
[ 0.207011] Can't analyze schedule() prologue at 80352ab0
[ 0.261962] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.273109] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.286095] rt2880_gpio 10000660.gpio: registering 6 gpios
[ 0.297062] rt2880_gpio 10000660.gpio: registering 6 irq handlers
[ 0.320369] clocksource: Switched to clocksource MIPS
[ 0.332573] NET: Registered protocol family 2
[ 0.343111] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.356993] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.369564] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.382570] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.394211] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.407141] NET: Registered protocol family 1
[ 0.422645] rt-timer 10000100.timer: maximum frequency is 3662Hz
[ 0.436201] Crashlog allocated RAM at address 0x1f00000
[ 0.451287] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[ 0.474764] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.486361] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.534180] io scheduler noop registered
[ 0.541954] io scheduler deadline registered (default)
[ 0.554102] gpio-export gpio_export: 2 gpio(s) exported
[ 0.564998] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.583700] console [ttyS0] disabled
[ 0.590886] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.610610] console [ttyS0] enabled
[ 0.610610] console [ttyS0] enabled
[ 0.624383] bootconsole [early0] disabled
[ 0.624383] bootconsole [early0] disabled
[ 0.641354] cacheinfo: Failed to find cpu0 device node
[ 0.651729] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.684299] spi spi0.0: force spi mode3
[ 0.693469] m25p80 spi0.0: pm25lq032 (4096 Kbytes)
[ 0.703228] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.715949] Creating 4 MTD partitions on "spi0.0":
[ 0.725590] 0x000000000000-0x000000030000 : "u-boot"
[ 0.737406] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.749940] 0x000000040000-0x000000050000 : "factory"
[ 0.762098] 0x000000050000-0x000000400000 : "firmware"
[ 1.239968] 2 uimage-fw partitions found on MTD device firmware
[ 1.251944] 0x000000050000-0x00000019e82b : "kernel"
[ 1.263759] 0x00000019e82b-0x000000400000 : "rootfs"
[ 1.275451] mtd: device 5 (rootfs) set to be root filesystem
[ 1.291026] 1 squashfs-split partitions found on MTD device rootfs
[ 1.303535] 0x0000003cf000-0x000000400000 : "rootfs_data"
[ 1.317208] libphy: Fixed MDIO Bus: probed
[ 1.334976] rt3050-esw 10110000.esw: link changed 0x00
[ 1.348351] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.365970] rt2880_wdt 10000120.watchdog: Initialized
[ 1.378663] NET: Registered protocol family 10
[ 1.397621] Segment Routing with IPv6
[ 1.405290] NET: Registered protocol family 17
[ 1.414378] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you nee
d this.
[ 1.440310] 8021q: 802.1Q VLAN Support v1.8
[ 1.468752] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.485086] Freeing unused kernel memory: 200K
[ 1.494070] This architecture does not have kernel memory protection.
[ 2.630413] random: fast init done
[ 3.214858] init: Console is alive
[ 3.222397] init: - watchdog -
[ 5.181910] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.496752] usbcore: registered new interface driver usbfs
[ 5.508082] usbcore: registered new interface driver hub
[ 5.519102] usbcore: registered new device driver usb
[ 5.541673] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.557869] ehci-platform: EHCI generic platform driver
[ 5.579068] phy phy-usbphy.0: remote usb device wakeup disabled
[ 5.590947] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 5.599835] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 5.611428] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 5.627552] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 5.660454] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 5.675225] hub 1-0:1.0: USB hub found
[ 5.684026] hub 1-0:1.0: 1 port detected
[ 5.698782] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.714247] ohci-platform: OHCI generic platform driver
[ 5.725317] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 5.739075] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 5.755170] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 5.836363] hub 2-0:1.0: USB hub found
[ 5.845069] hub 2-0:1.0: 1 port detected
[ 5.973164] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.998649] init: - preinit -
[ 7.930772] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug[ 8.259245] random: procd: uninitialized urandom read (4 bytes read
)
level
[ 11.684183] jffs2: notice: (362) jffs2_build_xattr_subsystem: complete building xattr subsystem, 18 of xdatum (3 unchecked, 15 orphan) an
d 22 of xref (15 dead, 0 orphan) found.
[ 11.720093] mount_root: switching to jffs2 overlay
[ 11.794355] overlayfs: upper fs does not support tmpfile.
[ 11.820309] urandom-seed: Seeding with /etc/urandom.seed
[ 11.918490] procd: - early -
[ 11.924795] procd: - watchdog -
[ 13.073976] procd: - watchdog -
[ 13.081239] procd: - ubus -
[ 13.487129] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.625629] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.639497] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.655360] procd: - init -
Please press Enter to activate this console.
[ 14.308105] kmodloader: loading kernel modules from /etc/modules.d/*
[ 14.334265] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.369237] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 14.385356] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 14.407161] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.435575] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 14.574540] xt_time: kernel timezone is -0000
[ 14.692257] PPP generic driver version 2.4.2
[ 14.706631] NET: Registered protocol family 24
[ 14.764138] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 14.778721] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 14.794257] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 14.859941] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.716141] urandom_read: 5 callbacks suppressed
[ 16.716157] random: jshn: uninitialized urandom read (4 bytes read)
[ 32.165685] br-lan: port 1(eth0) entered blocking state
[ 32.176256] br-lan: port 1(eth0) entered disabled state
[ 32.187415] device eth0 entered promiscuous mode
[ 32.302020] br-lan: port 1(eth0) entered blocking state
[ 32.312577] br-lan: port 1(eth0) entered forwarding state
[ 32.323842] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 33.190562] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 36.009773] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 40.585070] wlan0: authenticate with 34:ce:00:65:aa:d5
[ 40.611016] wlan0: send auth to 34:ce:00:65:aa:d5 (try 1/3)
[ 40.657908] wlan0: send auth to 34:ce:00:65:aa:d5 (try 2/3)
[ 40.701981] wlan0: send auth to 34:ce:00:65:aa:d5 (try 3/3)
[ 40.733323] wlan0: authentication with 34:ce:00:65:aa:d5 timed out
[ 42.102938] wlan0: authenticate with 34:ce:00:65:aa:d5
[ 42.115859] wlan0: send auth to 34:ce:00:65:aa:d5 (try 1/3)
[ 42.130036] wlan0: authenticated
[ 42.140557] wlan0: associate with 34:ce:00:65:aa:d5 (try 1/3)
[ 42.155641] wlan0: RX AssocResp from 34:ce:00:65:aa:d5 (capab=0x431 status=0 aid=2)
[ 42.171545] wlan0: associated
[ 42.199100] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 106.060582] random: crng init done
- Po
U-Boot 1.1.3 Rev 0.3 by WErt(WErt) 4PDA (May 19 2016 - 14:41:04)
Board: Ralink APSoC DRAM: 32 MB
******************************
Software System Reset Occurred
******************************
Ralink SPI flash driver, SPI clock: 15MHz
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128FV
.*** Warning - bad CRC, using default environment
============================================
Ralink U-Boot Version: 5.0.0.5
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date:May 19 2016 Time:14:41:04
============================================
icache: sets:256, ways:4, linesz:32, total:32768
dcache: sets:128, ways:4, linesz:32, total:16384
#### The CPU freq = 360 MHZ ####
estimate memory size = 32 Mbytes
Please choose the operation:
0: Load system code then write to Flash via Serial.
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Enter boot command line interface.
5: Load system code then write to Flash via USB Storage.
6: Load U-Boot code then write to Flash via USB Storage.
7: Load U-Boot code then write to Flash via Serial.
8: Load U-Boot code to SDRAM via TFTP.
9: Load U-Boot code then write to Flash via TFTP. 0
.
3: System Boot system code via Flash.
## Checking image at bc050000 ...
. Image Name: MIPS OpenWrt Linux-4.14.95
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1413077 Bytes = 1.3 MB
Load Address: 80000000
Entry Point: 80000000
...................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
[ 0.000000] Linux version 4.14.95 (dev@catservice2) (gcc version 7.3.0 (OpenWrt GCC 7
.3.0 r7676-cddd7b4c77)) #0 Wed Jan 30 12:21:02 2019
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is A5-V11
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_in
it=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=0000b9e0
[ 0.000000] Readback ErrCtl register=0000b9e0
[ 0.000000] Memory: 27784K/32768K available (3276K kernel code, 164K rwdata, 768K rod
ata, 200K init, 195K bss, 4984K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 58326
1500 ns
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns:
10618113593 ns
[ 0.000016] sched_clock: 32 bits at 180MHz, resolution 5ns, wraps every 11930464253ns
[ 0.015700] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.098043] pid_max: default: 32768 minimum: 301
[ 0.107619] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.120732] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.143643] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_n
s: 19112604462750000 ns
[ 0.163208] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.175460] pinctrl core: initialized pinctrl subsystem
[ 0.186967] NET: Registered protocol family 16
[ 0.255936] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.267078] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.280077] rt2880_gpio 10000660.gpio: registering 6 gpios
[ 0.291034] rt2880_gpio 10000660.gpio: registering 6 irq handlers
[ 0.313754] clocksource: Switched to clocksource MIPS
[ 0.326048] NET: Registered protocol family 2
[ 0.336352] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350236] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.362806] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.375808] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.387450] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400383] NET: Registered protocol family 1
[ 0.415870] rt-timer 10000100.timer: maximum frequency is 3662Hz
[ 0.429592] Crashlog allocated RAM at address 0x1f00000
[ 0.444804] workingset: timestamp_bits=30 max_order=13 bucket_order=0
[ 0.468504] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.480102] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2
001-2006 Red Hat, Inc.
[ 0.527498] io scheduler noop registered
[ 0.535281] io scheduler deadline registered (default)
[ 0.547180] gpio-export gpio_export: 2 gpio(s) exported
[ 0.558134] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.572844] console [ttyS0] disabled
[ 0.580033] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 250000
0) is a Palmchip BK-3103
[ 0.599757] console [ttyS0] enabled
[ 0.599757] console [ttyS0] enabled
[ 0.613535] bootconsole [early0] disabled
[ 0.613535] bootconsole [early0] disabled
[ 0.630446] cacheinfo: Failed to find cpu0 device node
[ 0.640819] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.666654] spi spi0.0: force spi mode3
[ 0.686400] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.695957] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.708691] Creating 4 MTD partitions on "spi0.0":
[ 0.718334] 0x000000000000-0x000000030000 : "u-boot"
[ 0.730163] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.742679] 0x000000040000-0x000000050000 : "factory"
[ 0.754962] 0x000000050000-0x000001000000 : "firmware"
[ 2.633394] 2 uimage-fw partitions found on MTD device firmware
[ 2.645369] 0x000000050000-0x0000001a9015 : "kernel"
[ 2.655321] random: fast init done
[ 2.664075] 0x0000001a9015-0x000001000000 : "rootfs"
[ 2.675789] mtd: device 5 (rootfs) set to be root filesystem
[ 2.691206] 1 squashfs-split partitions found on MTD device rootfs
[ 2.703721] 0x000000383000-0x000001000000 : "rootfs_data"
[ 2.717403] libphy: Fixed MDIO Bus: probed
[ 2.735342] rt3050-esw 10110000.esw: link changed 0x00
[ 2.747480] mtk_soc_eth 10100000.ethernet: generated random MAC address 92:40:d0:c3:1
7:3b
[ 2.765191] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000,
irq 5
[ 2.782860] rt2880_wdt 10000120.watchdog: Initialized
[ 2.795664] NET: Registered protocol family 10
[ 2.814226] Segment Routing with IPv6
[ 2.821735] NET: Registered protocol family 17
[ 2.830861] 8021q: 802.1Q VLAN Support v1.8
[ 2.857799] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.874209] Freeing unused kernel memory: 200K
[ 2.883078] This architecture does not have kernel memory protection.
[ 4.457612] init: Console is alive
[ 4.465151] init: - watchdog -
[ 6.358476] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.677541] usbcore: registered new interface driver usbfs
[ 6.688866] usbcore: registered new interface driver hub
[ 6.699875] usbcore: registered new device driver usb
[ 6.722912] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.739270] ehci-platform: EHCI generic platform driver
[ 6.760468] phy phy-usbphy.0: remote usb device wakeup disabled
[ 6.772352] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 6.781301] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.792910] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number
1
[ 6.809040] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.843895] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.858552] hub 1-0:1.0: USB hub found
[ 6.867346] hub 1-0:1.0: 1 port detected
[ 6.882005] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.898078] ohci-platform: OHCI generic platform driver
[ 6.909208] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.922961] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number
2
[ 6.939007] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 7.019711] hub 2-0:1.0: USB hub found
[ 7.028375] hub 2-0:1.0: 1 port detected
[ 7.045784] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.071322] init: - preinit -
[ 8.097347] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.479131] random: procd: uninitialized urandom read (4 bytes read)
[ 8.970572] rt3050-esw 10110000.esw: link changed 0x00
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 14.108354] jffs2: notice: (347) jffs2_build_xattr_subsystem: complete building xattr
subsystem, 9 of xdatum (2 unchecked, 7 orphan) and 10 of xref (7 dead, 0 orphan) found.
[ 14.144199] mount_root: switching to jffs2 overlay
[ 14.207395] overlayfs: upper fs does not support tmpfile.
[ 14.231942] urandom-seed: Seeding with /etc/urandom.seed
[ 14.460980] procd: - early -
[ 14.467184] procd: - watchdog -
[ 15.343280] procd: - watchdog -
[ 15.350661] procd: - ubus -
[ 15.449271] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.467505] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.481479] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.497239] procd: - init -
Please press Enter to activate this console.
[ 16.158714] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.185739] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.221888] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c1
80
[ 16.238015] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 16.260257] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.288920] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 16.428354] xt_time: kernel timezone is -0000
[ 16.541354] PPP generic driver version 2.4.2
[ 16.556184] NET: Registered protocol family 24
[ 16.616059] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 16.630615] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 16.646188] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 16.704234] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 18.719196] urandom_read: 5 callbacks suppressed
[ 18.719213] random: jshn: uninitialized urandom read (4 bytes read)
[ 31.264744] br-lan: port 1(eth0) entered blocking state
[ 31.275345] br-lan: port 1(eth0) entered disabled state
[ 31.286499] device eth0 entered promiscuous mode
[ 31.354153] br-lan: port 1(eth0) entered blocking state
[ 31.364691] br-lan: port 1(eth0) entered forwarding state
[ 31.375918] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 32.303987] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 36.669419] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.693949] br-lan: port 2(wlan0) entered blocking state
[ 36.704651] br-lan: port 2(wlan0) entered disabled state
[ 36.716034] device wlan0 entered promiscuous mode
[ 37.570669] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 37.584024] br-lan: port 2(wlan0) entered blocking state
[ 37.594739] br-lan: port 2(wlan0) entered forwarding state
[ 113.647683] random: crng init done
Jest coś co pominąłem?
Jeszcze kilka poleceń i ich wyniki:
root@OpenWrt:/# iwinfo wlan0 info
wlan0 ESSID: "LEDE_TEST"
Access Point: A6:7B:28:A7:2C:96
Mode: Master Channel: 11 (2.462 GHz)
Tx-Power: 20 dBm Link Quality: unknown/70
Signal: unknown Noise: unknown
Bit Rate: unknown
Encryption: mixed WPA/WPA2 PSK (CCMP)
Type: nl80211 HW Mode(s): 802.11bgn
Hardware: unknown [Generic MAC80211]
TX power offset: unknown
Frequency offset: unknown
Supports VAPs: yes PHY name: phy0root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr 5E:A1:9B:AC:F1:16
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fd25:abb4:831c::1/60 Scope:Global
inet6 addr: fe80::5ca1:9bff:feac:f116/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:2132 (2.0 KiB)
eth0 Link encap:Ethernet HWaddr 5E:A1:9B:AC:F1:16
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:22 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3761 (3.6 KiB)
Interrupt:5
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:256 errors:0 dropped:0 overruns:0 frame:0
TX packets:256 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:17408 (17.0 KiB) TX bytes:17408 (17.0 KiB)
wlan0 Link encap:Ethernet HWaddr A6:7B:28:A7:2C:96
inet6 addr: fe80::a47b:28ff:fea7:2c96/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1344 (1.3 KiB)