Po prostu włącz wifi, domyślnie w lede/openwrt jest wyłączone. I to wszystko co musisz robić w konfiguracji (no, może poza szyfrowaniem). Jeżeli zdążyłeś już namieszać to pokaż wyniki poleceń:

uci show network
uci show wireless
uci show firewall

# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd25:c4dc:68e9::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan.ifname='eth0.1 eth0.2'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='20:28:18:a2:07:66'
network.wan_dev=device
network.wan_dev.name='eth0.2'
network.wan_dev.macaddr='20:28:18:a2:07:67'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='4 6t'
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device='switch0'
network.@switch_vlan[1].vlan='2'
network.@switch_vlan[1].ports='0 6t'
network.wan=interface
network.wan.proto='dhcp'
network.wan.ifname='eth1'

# uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.channel='11'
wireless.radio0.hwmode='11g'
wireless.radio0.path='platform/10180000.wmac'
wireless.radio0.htmode='HT20'
wireless.radio0.country='PL'
wireless.radio0.legacy_rates='1'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.mode='ap'
wireless.default_radio0.ssid='OpenWrt'
wireless.default_radio0.network='lan'
wireless.default_radio0.encryption='psk-mixed'
wireless.default_radio0.key='password123'

# uci show firewall
firewall.@defaults[0]=defaults
firewall.@defaults[0].syn_flood='1'
firewall.@defaults[0].input='ACCEPT'
firewall.@defaults[0].output='ACCEPT'
firewall.@defaults[0].forward='REJECT'
firewall.@zone[0]=zone
firewall.@zone[0].name='lan'
firewall.@zone[0].network='lan'
firewall.@zone[0].input='ACCEPT'
firewall.@zone[0].output='ACCEPT'
firewall.@zone[0].forward='ACCEPT'
firewall.@zone[1]=zone
firewall.@zone[1].name='wan'
firewall.@zone[1].network='wan' 'wan6'
firewall.@zone[1].input='REJECT'
firewall.@zone[1].output='ACCEPT'
firewall.@zone[1].forward='REJECT'
firewall.@zone[1].masq='1'
firewall.@zone[1].mtu_fix='1'
firewall.@forwarding[0]=forwarding
firewall.@forwarding[0].src='lan'
firewall.@forwarding[0].dest='wan'
firewall.@rule[0]=rule
firewall.@rule[0].name='Allow-DHCP-Renew'
firewall.@rule[0].src='wan'
firewall.@rule[0].proto='udp'
firewall.@rule[0].dest_port='68'
firewall.@rule[0].target='ACCEPT'
firewall.@rule[0].family='ipv4'
firewall.@rule[1]=rule
firewall.@rule[1].name='Allow-Ping'
firewall.@rule[1].src='wan'
firewall.@rule[1].proto='icmp'
firewall.@rule[1].icmp_type='echo-request'
firewall.@rule[1].family='ipv4'
firewall.@rule[1].target='ACCEPT'
firewall.@rule[2]=rule
firewall.@rule[2].name='Allow-IGMP'
firewall.@rule[2].src='wan'
firewall.@rule[2].proto='igmp'
firewall.@rule[2].family='ipv4'
firewall.@rule[2].target='ACCEPT'
firewall.@rule[3]=rule
firewall.@rule[3].name='Allow-DHCPv6'
firewall.@rule[3].src='wan'
firewall.@rule[3].proto='udp'
firewall.@rule[3].src_ip='fc00::/6'
firewall.@rule[3].dest_ip='fc00::/6'
firewall.@rule[3].dest_port='546'
firewall.@rule[3].family='ipv6'
firewall.@rule[3].target='ACCEPT'
firewall.@rule[4]=rule
firewall.@rule[4].name='Allow-MLD'
firewall.@rule[4].src='wan'
firewall.@rule[4].proto='icmp'
firewall.@rule[4].src_ip='fe80::/10'
firewall.@rule[4].icmp_type='130/0' '131/0' '132/0' '143/0'
firewall.@rule[4].family='ipv6'
firewall.@rule[4].target='ACCEPT'
firewall.@rule[5]=rule
firewall.@rule[5].name='Allow-ICMPv6-Input'
firewall.@rule[5].src='wan'
firewall.@rule[5].proto='icmp'
firewall.@rule[5].icmp_type='echo-request' 'echo-reply' 'destination-unreachable' 'packet-too-big' 'time-exceeded' 'bad-header' 'unknown-header-type' 'router-solicitation' 'neighbour-solicitation' 'router-advertisement' 'neighbour-advertisement'
firewall.@rule[5].limit='1000/sec'
firewall.@rule[5].family='ipv6'
firewall.@rule[5].target='ACCEPT'
firewall.@rule[6]=rule
firewall.@rule[6].name='Allow-ICMPv6-Forward'
firewall.@rule[6].src='wan'
firewall.@rule[6].dest='*'
firewall.@rule[6].proto='icmp'
firewall.@rule[6].icmp_type='echo-request' 'echo-reply' 'destination-unreachable' 'packet-too-big' 'time-exceeded' 'bad-header' 'unknown-header-type'
firewall.@rule[6].limit='1000/sec'
firewall.@rule[6].family='ipv6'
firewall.@rule[6].target='ACCEPT'
firewall.@rule[7]=rule
firewall.@rule[7].name='Allow-IPSec-ESP'
firewall.@rule[7].src='wan'
firewall.@rule[7].dest='lan'
firewall.@rule[7].proto='esp'
firewall.@rule[7].target='ACCEPT'
firewall.@rule[8]=rule
firewall.@rule[8].name='Allow-ISAKMP'
firewall.@rule[8].src='wan'
firewall.@rule[8].dest='lan'
firewall.@rule[8].dest_port='500'
firewall.@rule[8].proto='udp'
firewall.@rule[8].target='ACCEPT'
firewall.@include[0]=include
firewall.@include[0].path='/etc/firewall.user'

zrobiłem to ale nic nie dało, cofnąłem zmiany, i na aero2 wykupiłem pakiet, jest teraz bez kapcha, ale i tak nie działa.
Generalnie to kapcha mnie nie interesuje, bo i tak będę działał na pakietach płatnych.
I tu prośba o pomoc, bo i tak, mimo zdjęcia kapcha, nie działa.

Czemu używasz totalnie nieopłacalnego Aero2 na płatnych pakietach?

odp:

# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd25:c4dc:68e9::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.1'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan.ifname='eth0.1 eth0.2'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='20:28:18:a2:07:66'
network.wan_dev=device
network.wan_dev.name='eth0.2'
network.wan_dev.macaddr='20:28:18:a2:07:67'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='4 6t'
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device='switch0'
network.@switch_vlan[1].vlan='2'
network.@switch_vlan[1].ports='0 6t'
network.wan=interface
network.wan.proto='dhcp'
network.wan.ifname='eth1'

# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.1.1     0.0.0.0         UG    0      0        0 eth1
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 br-lan
192.168.1.0     0.0.0.0         255.255.255.0   U     0      0        0 eth1

# ifstatus wan
{
    "up": true,
    "pending": false,
    "available": true,
    "autostart": true,
    "dynamic": false,
    "uptime": 6579,
    "l3_device": "eth1",
    "proto": "dhcp",
    "device": "eth1",
    "updated": [
        "addresses",
        "routes",
        "data"
    ],
    "metric": 0,
    "dns_metric": 0,
    "delegation": true,
    "ipv4-address": [
        {
            "address": "192.168.1.100",
            "mask": 24
        }
    ],
    "ipv6-address": [
       
    ],
    "ipv6-prefix": [
       
    ],
    "ipv6-prefix-assignment": [
       
    ],
    "route": [
        {
            "target": "0.0.0.0",
            "mask": 0,
            "nexthop": "192.168.1.1",
            "source": "192.168.1.100\/32"
        }
    ],
    "dns-server": [
        "192.168.1.1",
        "192.168.1.1"
    ],
    "dns-search": [
       
    ],
    "inactive": {
        "ipv4-address": [
           
        ],
        "ipv6-address": [
           
        ],
        "route": [
           
        ],
        "dns-server": [
           
        ],
        "dns-search": [
           
        ]
    },
    "data": {
        "leasetime": 86400
    }
}

ping do google nie działa ani z rutera ani z kompa
ping do 8.8.8.8 z kompa działa (za pierwszym razem zawsze timeout, ale kolejne już ok), z rutera zapewne też ale nie chce mi komendy wykonać (używam własnych komend z menu graficznego)
adres nadany przez dhcp na kompie 192.168.1.122 po wifi