FAQ o OpenWrt | Sprzedam różne routery | Oddam

Zuzia · 2018-10-25 19:17:12

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Na wszelki wypadek zgram i wykonam testy zmiany softu z obydwu wersji.

Bootlog z firmware V1.00(TM):

CDW57CDL_003 Jboot B895
JRecovery Version R1.2 2015/08/31 17:24
spi device id: ef 40 18 0 0 (40180000)
SPI FLASH: W25Q128FV 16M
.
....................
Starting kernel @80000000...

LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (tja@localhost.localdomain) (gcc version 4.3.5 (Buildroot 2011.05) ) #10 Thu Feb 18 16:29:01 CST 2016
CMD_LINE:console=ttyS1,57600n8 root=/dev/mtdblock3

 The CPU feqenuce set to 580 MHz
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0006e88b
Readback ErrCtl register=0006e88b
Memory: 60736k/65536k available (3163k kernel code, 4800k reserved, 767k data, 180k init, 0k highmem)
Hierarchical RCU implementation.
    RCU debugfs-based tracing is enabled.
    Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Console: colour dummy device 80x25
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 40a09d
RALINK_GPIOMODE = 40a09d
PPLL_CFG1=0xe64000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20100000
res[0]->end = 201fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 118
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Enable Ralink GDMA Controller Module 
GDMA IP Version=3
======================================
   SPI driver, modified by Jason
======================================
<-----
0x60: 0x0040809d
-----
spidrv_major = 217
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : ef 40 18 0 0 (40180000)
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 4096
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "Whole"
0x000000000000-0x000000010000 : "Bootloader"
0x000000010000-0x000000150000 : "Kernel"
0x000000180000-0x000000e90000 : "RootFS"
0x000000e90000-0x000000f10000 : "Storage"
0x000000f10010-0x000000ff0000 : "UI"
mtd: partition "UI" doesn't start on an erase block boundary -- force read-only
0x000000ff0000-0x000001000000 : "Config"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x432880f8
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, Tx Ring = 256, Rx Ring = 256
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288071
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (949 buckets, 3796 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
gre: can't add protocol
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 180k freed
Inter-|   Receive                                                |  Transmit
 face |bytes    packets errs drop fifo fraswitch register base addr to system register 0xb0000000
me compressed muwrite offset 0x34, value 0x1800000
lticast|bytes   write offset 0x34, value 0x0
 packets errs drop fiRaeth v3.0 (foNAPI
 c,SkbRecycleol)
ls ca
phy_tx_ring = 0x03fc3000, tx_ring = 0xa3fc3000

phy_rx_ring0 = 0x03fc4000, rx_ring0 = 0xa3fc4000

 0x5,Read PhyID is 0x243 ,0xd91!!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288071
rrCDMA_CSG_CFG = 81000000
ieGDMA1_FWD_CFG = 20710000
r compressed
    lo:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  eth2:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
 tunl0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  gre0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  sit0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
ip6tnl0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
 flash_open: flash_fd=3
Mount D Section.
mount: /dev/mtdblock5 is write-protected, mounting read-only
 flash_open: flash_fd=9
switch register base addr to system register 0xb0000000
write offset 0x60, value 0x40a01d
addrconf_dad_completed 7
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
switch reg write offset=2014, value=10002
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10001
switch reg write offset=2514, value=10002
rmmod: hw_nat: No such file or directory
ifconfig: SIOCGIFFLAGS: No such device
bridge brx0 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx1 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx2 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx3 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx4 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx5 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx6 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx7 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx8 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx9 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx10 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx11 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx12 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx13 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx14 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx15 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx16 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx17 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx18 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx19 doesn't exist; can't delete it
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
iptables v1.4.10: Couldn't load target `block_br':File not found

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `block_br_input':File not found

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
vconfig: ioctl error for add: File exists
vconfig: ioctl error for add: File exists
Set port eth2.1.0 
vconfig: ioctl error for add: File exists
device eth2 entered promiscuous mode
set hello timer failed: Invalid argument
device eth2.1 entered promiscuous mode
br0: port 1(eth2.1) entering forwarding state
br0: port 1(eth2.1) entering forwarding state
sh: ebtables: not found
Set port eth2.2.0 
vconfig: ioctl error for add: File exists
Set port eth2.2.0 
vconfig: ioctl error for add: File exists
, Enable: 1
Wireless 5G AP0, Enable: 1
phy 0, reg 0, val 0x800
Set: phy[0].reg[0] = 0800
phy 1, reg 0, val 0x800
Set: phy[1].reg[0] = 0800
phy 2, reg 0, val 0x800
Set: phy[2].reg[0] = 0800
phy 3, reg 0, val 0x800
Set: phy[3].reg[0] = 0800
phy 4, reg 0, val 0x800
Set: phy[4].reg[0] = 0800
phy 5, reg 0, val 0x800
Set: phy[5].reg[0] = 0800
phy 6, reg 0, val 0x800
Set: phy[6].reg[0] = 0800
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
brctl addif br0 ra0
interface ra0 does not exist!
brctl addif br0 rai0
interface rai0 does not exist!
hw_nat: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Ralink HW NAT Module Enabled
phy 0, reg 0, val 0x3300
Set: phy[0].reg[0] = 3300
addrconf_dad_completed 7
phy 1, reg 0, val 0x3300
Set: phy[1].reg[0] = 3300
addrconf_dad_completed 7
addrconf_dad_completed 7
phy 2, reg 0, val 0x3300
Set: phy[2].reg[0] = 3300
phy 3, reg 0, val 0x3300
Set: phy[3].reg[0] = 3300
phy 4, reg 0, val 0x3300
Set: phy[4].reg[0] = 3300
phy 5, reg 0, val 0x3300
Set: phy[5].reg[0] = 3300
phy 6, reg 0, val 0x3300
Set: phy[6].reg[0] = 3300
init vlan
init lan
init stp
init ondemand
init multiwan2
init multi_ondemand
init routing
init nat
==== NAT START (WAN:ALL Func:ALL) ====
cat: /var/nat/nat.wan: No such file or directory
ESW: Link Status Changed - Port1 Link UP
/var/nat/nat-draft.uyg: /var/nat/nat-draft.uyg: 131: cannot create /proc/sys/net/ipv4/route/secret_interval: Directory nonexistent
SINGLE DMZ start
gre_post
addrconf_dad_completed 7
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
modprobe: module ip6_tables not found
modprobe: failed to load module ip6_tables
ip6tables v1.4.10: can't initialize ip6tables table `filter': iptables who? (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
init dhcpsrv
server_config.pool_check = 1

server_config.pool_check = 1

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

0

Unable to open /var/run/udhcpd.leases for reading
udhcpd (v0.9.9-pre) started
Unable to open /var/run/udhcpd.leases for reading
init dnsrelay
init spap
init ddns
init snmp
init route_protocol
rm: cannot remove '/etc/ripd.conf': No such file or directory
cat: /var/run/ripd.pid: No such file or directory
BusyBox v1.3.2 (2015-12-09 19:52:49 CST) multi-call binary

Usage: kill [-l] [-signal] process-id [process-id ...]

cat: /var/run/zebra.pid: No such file or directory
BusyBox v1.3.2 (2015-12-09 19:52:49 CST) multi-call binary

Usage: kill [-l] [-signal] process-id [process-id ...]

init load_balance
init time
timezone:-60
dsttime:0
init rbydom
init rbyip
init qos
init keepalive
init user
init ftp_alg
init rtsp_alg
init schedule
init mupnpd
init watchdog
init reboot
init wireless_mode
server_config.pool_check = 1

server_config.pool_check = 1

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

0

udhcpd (v0.9.9-pre) started
init wlanap
Length of MAC:6
 mac:6c:72:20:a5:9e:f8:
----


=== pAd = c0882000, size = 1632152 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
device_id =0x7650
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
MACVersion = 0x76502000
load fw spent 12ms
RX DESC a2ad2000 size = 2048
RX1 DESC a2ad3000 size = 2048
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
2a:55:44:e4:05:1a:cb:eb:01:93:83:88:b2:c3:4f:8f:
50:b2:65:62:c1:a3:cb:f9:52:8e:b0:b1:79:c9:b6:97:

1. Phy Mode = 49
2. Phy Mode = 49
ext_pa_current_setting = 1
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Main bssid = 6c:72:20:a5:9e:f8
<==== rt28xx_init, Status=0
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
0x1300 = 00064300
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
device rai0 entered promiscuous mode
br0: port 2(rai0) entering forwarding state
br0: port 2(rai0) entering forwarding state
killall: check_status2: no process killed
route: SIOC[ADD|DEL]RT: No such device
wscd: SSDP UDP PORT = 1900
Invalid command : ledflashstop
device wdsi0 is not a slave of br0
device wdsi1 is not a slave of br0
device wdsi2 is not a slave of br0
device wdsi3 is not a slave of br0
device rai0 left promiscuous mode
br0: port 2(rai0) entering forwarding state
==>MT76x0_WLAN_ChipOnOff(): OnOff:0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xff000003
init wps_status
init wps_btn
init wpa
init ipv6
init v6filter
modprobe: module ip6_tables not found
modprobe: failed to load module ip6_tables
modprobe: module ip6table_filter not found
modprobe: failed to load module ip6table_filter
modprobe: module ip6table_mangle not found
modprobe: failed to load module ip6table_mangle
modprobe: module ip6t_rt not found
modprobe: failed to load module ip6t_rt
modprobe: module ip6t_REJECT not found
modprobe: failed to load module ip6t_REJECT
init ddnsv6
init hwnat
init 3g_status
init sip_alg
init igmp
init reset_btn
init ate
killall: ated: no process killed
init wan_led
init recent
init httpd
init telnetd
/usr/bin/telnetd-action: Don't Start telnetd since CSID is set disable ...
/usr/bin/ataskset: /usr/bin/ataskset: 6: taskset: not found
/usr/bin/telnetd-action start ok
 flash_open: flash_fd=4
 flash_open: flash_fd=4
 framtd_erase: addr:ff0000 len:0
lash_open: flash_fd=9
ramtd_write: to:ff0000 len:10
ramtd_write: to:ff0010 len:58e
ramtd_write: to:ff0000 len:1
 flash_open: flash_fd=4
addrconf_dad_completed 7
# Length of MAC:6
 mac:6c:72:20:a5:9e:f7:
----


=== pAd = c11c6000, size = 960336 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6
RX DESC a29d6000  size = 2048
RTMP_TimerListAdd: add timer obj c1231638!
RTMP_TimerListAdd: add timer obj c11ce23c!
RTMP_TimerListAdd: add timer obj c11cde30!
RTMP_TimerListAdd: add timer obj c11ce20c!
RTMP_TimerListAdd: add timer obj c11ce548!
RTMP_TimerListAdd: add timer obj c11ce488!
RTMP_TimerListAdd: add timer obj c11ce4b8!
RTMP_TimerListAdd: add timer obj c11d1648!
RTMP_TimerListAdd: add timer obj c11d123c!
RTMP_TimerListAdd: add timer obj c11d1618!
RTMP_TimerListAdd: add timer obj c11d1954!
RTMP_TimerListAdd: add timer obj c11d1894!
RTMP_TimerListAdd: add timer obj c11d18c4!
RTMP_TimerListAdd: add timer obj c11d4a54!
RTMP_TimerListAdd: add timer obj c11d4648!
RTMP_TimerListAdd: add timer obj c11d4a24!
RTMP_TimerListAdd: add timer obj c11d4d60!
RTMP_TimerListAdd: add timer obj c11d4ca0!
RTMP_TimerListAdd: add timer obj c11d4cd0!
RTMP_TimerListAdd: add timer obj c11d7e60!
RTMP_TimerListAdd: add timer obj c11d7a54!
RTMP_TimerListAdd: add timer obj c11d7e30!
RTMP_TimerListAdd: add timer obj c11d816c!
RTMP_TimerListAdd: add timer obj c11d80ac!
RTMP_TimerListAdd: add timer obj c11d80dc!
RTMP_TimerListAdd: add timer obj c11db26c!
RTMP_TimerListAdd: add timer obj c11dae60!
RTMP_TimerListAdd: add timer obj c11db23c!
RTMP_TimerListAdd: add timer obj c11db578!
RTMP_TimerListAdd: add timer obj c11db4b8!
RTMP_TimerListAdd: add timer obj c11db4e8!
RTMP_TimerListAdd: add timer obj c11de678!
RTMP_TimerListAdd: add timer obj c11de26c!
RTMP_TimerListAdd: add timer obj c11de648!
RTMP_TimerListAdd: add timer obj c11de984!
RTMP_TimerListAdd: add timer obj c11de8c4!
RTMP_TimerListAdd: add timer obj c11de8f4!
RTMP_TimerListAdd: add timer obj c11e1a84!
RTMP_TimerListAdd: add timer obj c11e1678!
RTMP_TimerListAdd: add timer obj c11e1a54!
RTMP_TimerListAdd: add timer obj c11e1d90!
RTMP_TimerListAdd: add timer obj c11e1cd0!
RTMP_TimerListAdd: add timer obj c11e1d00!
RTMP_TimerListAdd: add timer obj c11e4e90!
RTMP_TimerListAdd: add timer obj c11e4a84!
RTMP_TimerListAdd: add timer obj c11e4e60!
RTMP_TimerListAdd: add timer obj c11e519c!
RTMP_TimerListAdd: add timer obj c11e50dc!
RTMP_TimerListAdd: add timer obj c11e510c!
RTMP_TimerListAdd: add timer obj c11e829c!
RTMP_TimerListAdd: add timer obj c11e7e90!
RTMP_TimerListAdd: add timer obj c11e826c!
RTMP_TimerListAdd: add timer obj c11e85a8!
RTMP_TimerListAdd: add timer obj c11e84e8!
RTMP_TimerListAdd: add timer obj c11e8518!
RTMP_TimerListAdd: add timer obj c11eb6a8!
RTMP_TimerListAdd: add timer obj c11eb29c!
RTMP_TimerListAdd: add timer obj c11eb678!
RTMP_TimerListAdd: add timer obj c11eb9b4!
RTMP_TimerListAdd: add timer obj c11eb8f4!
RTMP_TimerListAdd: add timer obj c11eb924!
RTMP_TimerListAdd: add timer obj c11eeab4!
RTMP_TimerListAdd: add timer obj c11ee6a8!
RTMP_TimerListAdd: add timer obj c11eea84!
RTMP_TimerListAdd: add timer obj c11eedc0!
RTMP_TimerListAdd: add timer obj c11eed00!
RTMP_TimerListAdd: add timer obj c11eed30!
RTMP_TimerListAdd: add timer obj c11f1ec0!
RTMP_TimerListAdd: add timer obj c11f1ab4!
RTMP_TimerListAdd: add timer obj c11f1e90!
RTMP_TimerListAdd: add timer obj c11f21cc!
RTMP_TimerListAdd: add timer obj c11f210c!
RTMP_TimerListAdd: add timer obj c11f213c!
RTMP_TimerListAdd: add timer obj c11f52cc!
RTMP_TimerListAdd: add timer obj c11f4ec0!
RTMP_TimerListAdd: add timer obj c11f529c!
RTMP_TimerListAdd: add timer obj c11f55d8!
RTMP_TimerListAdd: add timer obj c11f5518!
RTMP_TimerListAdd: add timer obj c11f5548!
RTMP_TimerListAdd: add timer obj c11f86d8!
RTMP_TimerListAdd: add timer obj c11f82cc!
RTMP_TimerListAdd: add timer obj c11f86a8!
RTMP_TimerListAdd: add timer obj c11f89e4!
RTMP_TimerListAdd: add timer obj c11f8924!
RTMP_TimerListAdd: add timer obj c11f8954!
RTMP_TimerListAdd: add timer obj c11fbae4!
RTMP_TimerListAdd: add timer obj c11fb6d8!
RTMP_TimerListAdd: add timer obj c11fbab4!
RTMP_TimerListAdd: add timer obj c11fbdf0!
RTMP_TimerListAdd: add timer obj c11fbd30!
RTMP_TimerListAdd: add timer obj c11fbd60!
RTMP_TimerListAdd: add timer obj c11feef0!
RTMP_TimerListAdd: add timer obj c11feae4!
RTMP_TimerListAdd: add timer obj c11feec0!
RTMP_TimerListAdd: add timer obj c11ff1fc!
RTMP_TimerListAdd: add timer obj c11ff13c!
RTMP_TimerListAdd: add timer obj c11ff16c!
RTMP_TimerListAdd: add timer obj c1207fa4!
RTMP_TimerListAdd: add timer obj c12080c0!
RTMP_TimerListAdd: add timer obj c1207fd0!
RTMP_TimerListAdd: add timer obj c11ff52c!
RTMP_TimerListAdd: add timer obj c11cb4cc!
RTMP_TimerListAdd: add timer obj c11ce8d8!
RTMP_TimerListAdd: add timer obj c11d1ce4!
RTMP_TimerListAdd: add timer obj c11d50f0!
RTMP_TimerListAdd: add timer obj c11d84fc!
RTMP_TimerListAdd: add timer obj c11db908!
RTMP_TimerListAdd: add timer obj c11ded14!
RTMP_TimerListAdd: add timer obj c11e2120!
RTMP_TimerListAdd: add timer obj c11e552c!
RTMP_TimerListAdd: add timer obj c11e8938!
RTMP_TimerListAdd: add timer obj c11ebd44!
RTMP_TimerListAdd: add timer obj c11ef150!
RTMP_TimerListAdd: add timer obj c11f255c!
RTMP_TimerListAdd: add timer obj c11f5968!
RTMP_TimerListAdd: add timer obj c11f8d74!
RTMP_TimerListAdd: add timer obj c11fc180!
RTMP_TimerListAdd: add timer obj c11ff240!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20 
E2PROM: 40 MW Power Delta= 0 
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 1, D2 = 4, CalCode = 7 !!!
RT6352_Temperature_Init : BBPR49 = 0x1
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff7
Current Temperature from BBP_R49=0xfffffff7
 TX BW Filter Calibration !!!
 RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= d, phase=3e)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase=3d)
TX IQ Calibration Done!
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c11ffab4!
Main bssid = 6c:72:20:a5:9e:f7
<==== rt28xx_init, Status=0
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering forwarding state
br0: port 2(ra0) entering forwarding state
Ralink HW NAT Module Disabled
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
Started WatchDog Timer. LoadVlaue: 36600 sysclk: 145000000 TIMEOUT: 60
addrconf_dad_completed 7
RTMP_TimerListAdd: add timer obj c0f88378!
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0xff000000, Reg-WlanFunCtrl=0xff000000
MACVersion = 0x76502000
load fw spent 0ms
RX DESC a2ad2000 size = 2048
RX1 DESC a2ad3000 size = 2048
ramtd_erase: addr:ff0000 len:0
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
2a:55:44:e4:05:1a:cb:eb:01:93:83:88:b2:c3:4f:8f:
50:b2:65:62:c1:a3:cb:f9:52:8e:b0:b1:79:c9:b6:97:

ramtd_write: to:ff0000 len:10
ramtd_write: to:ff0010 len:590
ramtd_write: to:ff0000 len:1
1. Phy Mode = 49
2. Phy Mode = 49
ext_pa_current_setting = 1
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Main bssid = 6c:72:20:a5:9e:f8
<==== rt28xx_init, Status=0
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
0x1300 = 00064300
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
device rai0 entered promiscuous mode
br0: port 3(rai0) entering forwarding state
br0: port 3(rai0) entering forwarding state
addrconf_dad_completed 7

Bootlog z firmware V1.00(PLAY)b02:

CDW57CDL_003 Jboot B895
JRecovery Version R1.2 2015/08/31 17:24
spi device id: ef 40 18 0 0 (40180000)
SPI FLASH: W25Q128FV 16M
.
....................
Starting kernel @80000000...

LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (tja@RD1) (gcc version 4.3.5 (Buildroot 2011.05) ) #10 Fri Sep 25 17:27:20 CST 2015
CMD_LINE:console=ttyS1,57600n8 root=/dev/mtdblock3

 The CPU feqenuce set to 580 MHz
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0006e880
Readback ErrCtl register=0006e880
Memory: 60736k/65536k available (3163k kernel code, 4800k reserved, 767k data, 180k init, 0k highmem)
Hierarchical RCU implementation.
    RCU debugfs-based tracing is enabled.
    Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Console: colour dummy device 80x25
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 40a09d
RALINK_GPIOMODE = 40a09d
PPLL_CFG1=0xe64000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20100000
res[0]->end = 201fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 118
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Ralink gpio driver initialized
Enable Ralink GDMA Controller Module 
GDMA IP Version=3
======================================
   SPI driver, modified by Jason
======================================
<-----
0x60: 0x0040809d
-----
spidrv_major = 217
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : ef 40 18 0 0 (40180000)
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 4096
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "Whole"
0x000000000000-0x000000010000 : "Bootloader"
0x000000010000-0x000000150000 : "Kernel"
0x000000180000-0x000000e90000 : "RootFS"
0x000000e90000-0x000000f10000 : "Storage"
0x000000f10010-0x000000ff0000 : "UI"
mtd: partition "UI" doesn't start on an erase block boundary -- force read-only
0x000000ff0000-0x000001000000 : "Config"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x432880f8
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, Tx Ring = 256, Rx Ring = 256
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288071
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (949 buckets, 3796 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
IPv4 over IPv4 tunneling driver
GRE over IPv4 demultiplexor driver
gre: can't add protocol
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 180k freed
Inter-|   Receive                                                |  Transmit
 face |bytes    packets errs drop fifo framswitch register base addr to system register 0xb0000000
e compressed mulwrite offset 0x34, value 0x1800000
ticast|bytes    write offset 0x34, value 0x0
packets errs drop fifRaeth v3.0 (o NAPI
co,SkbRecyclell)
s car
phy_tx_ring = 0x03fcb000, tx_ring = 0xa3fcb000

phy_rx_ring0 = 0x03fcc000, rx_ring0 = 0xa3fcc000

 0x5,Read PhyID is 0x243 ,0xd91!!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288071
riCDMA_CSG_CFG = 81000000
erGDMA1_FWD_CFG = 20710000
 compressed
    lo:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  eth2:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
 tunl0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  gre0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  sit0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
ip6tnl0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
 flash_open: flash_fd=3
Mount D Section.
mount: /dev/mtdblock5 is write-protected, mounting read-only
addrconf_dad_completed 7
 flash_open: flash_fd=10
switch register base addr to system register 0xb0000000
write offset 0x60, value 0x40a01d
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
switch reg write offset=2014, value=10002
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10001
switch reg write offset=2514, value=10002
rmmod: hw_nat: No such file or directory
ifconfig: SIOCGIFFLAGS: No such device
bridge brx0 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx1 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx2 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx3 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx4 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx5 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx6 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx7 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx8 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx9 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx10 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx11 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx12 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx13 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx14 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx15 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx16 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx17 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx18 doesn't exist; can't delete it
ifconfig: SIOCGIFFLAGS: No such device
bridge brx19 doesn't exist; can't delete it
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
iptables v1.4.10: Couldn't load target `block_br':File not found

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `block_br_input':File not found

Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
vconfig: ioctl error for add: File exists
vconfig: ioctl error for add: File exists
Set port eth2.1.0 
vconfig: ioctl error for add: File exists
device eth2 entered promiscuous mode
set hello timer failed: Invalid argument
device eth2.1 entered promiscuous mode
br0: port 1(eth2.1) entering forwarding state
br0: port 1(eth2.1) entering forwarding state
sh: ebtables: not found
Set port eth2.2.0 
vconfig: ioctl error for add: File exists
Set port eth2.2.0 
vconfig: ioctl error for add: File exists
, Enable: 1
Wireless 5G AP0, Enable: 1
phy 0, reg 0, val 0x800
Set: phy[0].reg[0] = 0800
phy 1, reg 0, val 0x800
Set: phy[1].reg[0] = 0800
phy 2, reg 0, val 0x800
Set: phy[2].reg[0] = 0800
phy 3, reg 0, val 0x800
Set: phy[3].reg[0] = 0800
phy 4, reg 0, val 0x800
Set: phy[4].reg[0] = 0800
phy 5, reg 0, val 0x800
Set: phy[5].reg[0] = 0800
phy 6, reg 0, val 0x800
Set: phy[6].reg[0] = 0800
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
sh: ebtables: not found
brctl addif br0 ra0
interface ra0 does not exist!
brctl addif br0 rai0
interface rai0 does not exist!
hw_nat: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Ralink HW NAT Module Enabled
phy 0, reg 0, val 0x3300
Set: phy[0].reg[0] = 3300
phy 1, reg 0, val 0x3300
Set: phy[1].reg[0] = 3300
addrconf_dad_completed 7
addrconf_dad_completed 7
phy 2, reg 0, val 0x3300
Set: phy[2].reg[0] = 3300
addrconf_dad_completed 7
phy 3, reg 0, val 0x3300
Set: phy[3].reg[0] = 3300
phy 4, reg 0, val 0x3300
Set: phy[4].reg[0] = 3300
phy 5, reg 0, val 0x3300
Set: phy[5].reg[0] = 3300
phy 6, reg 0, val 0x3300
Set: phy[6].reg[0] = 3300
init vlan
init lan
init stp
init wan
init ondemand
init multiwan
init multi_ondemand
init routing
init nat
==== NAT START (WAN:ALL Func:ALL) ====
ESW: Link Status Changed - Port1 Link UP
cat: /var/nat/nat.wan: No such file or directory
 framtd_erase: addr:ff0000 len:0
lash_open: flash_fd=10
ramtd_write: to:ff0000 len:10
ramtd_write: to:ff0010 len:5cc
ramtd_write: to:ff0000 len:1
/var/nat/nat-draft.uyg: /var/nat/nat-draft.uyg: 131: cannot create /proc/sys/net/ipv4/route/secret_interval: Directory nonexistent
addrconf_dad_completed 7
ESW: Link Status Changed - Port1 Link Down
SINGLE DMZ start
gre_post
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
modprobe: module ip6_tables not found
modprobe: failed to load module ip6_tables
ip6tables v1.4.10: can't initialize ip6tables table `filter': iptables who? (do you need to insmod?)
Perhaps ip6tables or your kernel needs to be upgraded.
/var/nat/nat-draft.uyg: /var/nat/nat-draft.uyg: 33: control: not found
init dhcpsrv
server_config.pool_check = 1

server_config.pool_check = 1

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

0

Unable to open /var/run/udhcpd.leases for reading
udhcpd (v0.9.9-pre) started
Unable to open /var/run/udhcpd.leases for reading
init dnsrelay
init spap
init ddns
init snmp
init route_protocol
rm: cannot remove '/etc/ripd.conf': No such file or directory
cat: /var/run/ripd.pid: No such file or directory
BusyBox v1.3.2 (2015-08-31 17:31:45 CST) multi-call binary

Usage: kill [-l] [-signal] process-id [process-id ...]

cat: /var/run/zebra.pid: No such file or directory
BusyBox v1.3.2 (2015-08-31 17:31:45 CST) multi-call binary

Usage: kill [-l] [-signal] process-id [process-id ...]

init load_balance
init time
timezone:-60
dsttime:0
init rbydom
init rbyip
init qos
init keepalive
init user
init ftp_alg
init rtsp_alg
init schedule
init mupnpd
init watchdog
init reboot
init wireless_mode
server_config.pool_check = 1

server_config.pool_check = 1

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0

0

udhcpd (v0.9.9-pre) started
init wlanap
ESW: Link Status Changed - Port1 Link UP
Length of MAC:6
 mac:6c:72:20:a5:9e:f8:
----


=== pAd = c0882000, size = 1632152 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
device_id =0x7650
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
MACVersion = 0x76502000
load fw spent 12ms
RX DESC a26e4000 size = 2048
RX1 DESC a26e5000 size = 2048
ESW: Link Status Changed - Port1 Link Down
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
2a:55:44:e4:05:1a:cb:eb:01:93:83:88:b2:c3:4f:8f:
50:b2:65:62:c1:a3:cb:f9:52:8e:b0:b1:79:c9:b6:97:

1. Phy Mode = 49
2. Phy Mode = 49
ext_pa_current_setting = 1
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Main bssid = 6c:72:20:a5:9e:f8
<==== rt28xx_init, Status=0
ESW: Link Status Changed - Port1 Link UP
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=3, PrimCh=48, HT-CentCh=46, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=48, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
0x1300 = 00064300
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
device rai0 entered promiscuous mode
br0: port 2(rai0) entering forwarding state
br0: port 2(rai0) entering forwarding state
ESW: Link Status Changed - Port1 Link Down
killall: check_status2: no process killed
route: SIOC[ADD|DEL]RT: No such device
wscd: SSDP UDP PORT = 1900
Invalid command : ledflashstop
device wdsi0 is not a slave of br0
device wdsi1 is not a slave of br0
device wdsi2 is not a slave of br0
device wdsi3 is not a slave of br0
device rai0 left promiscuous mode
br0: port 2(rai0) entering forwarding state
==>MT76x0_WLAN_ChipOnOff(): OnOff:0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xff000003
init wps_status
init wps_btn
init wpa
init ipv6
init v6filter
modprobe: module ip6_tables not found
modprobe: failed to load module ip6_tables
modprobe: module ip6table_filter not found
modprobe: failed to load module ip6table_filter
modprobe: module ip6table_mangle not found
modprobe: failed to load module ip6table_mangle
modprobe: module ip6t_rt not found
modprobe: failed to load module ip6t_rt
modprobe: module ip6t_REJECT not found
modprobe: failed to load module ip6t_REJECT
init ddnsv6
init failover
init hwnat
init 3g_status
init sip_alg
init igmp
init reset_btn
init ate
killall: ated: no process killed
init wan_led
init recent
init httpd
init telnetd
/usr/bin/telnetd-action: Don't Start telnetd since CSID is set disable ...
/usr/bin/telnetd-action start ok
/usr/bin/ataskset: /usr/bin/ataskset: 6: taskset: not found
 flash_open: flash_fd=4
 flash_open: flash_fd=4
 framtd_erase: addr:ff0000 len:0
lash_open: flash_fd=10
ramtd_write: to:ff0000 len:10
ramtd_write: to:ff0010 len:5ce
ramtd_write: to:ff0000 len:1
 flash_open: flash_fd=4
addrconf_dad_completed 7
ESW: Link Status Changed - Port1 Link UP
# ESW: Link Status Changed - Port1 Link Down
ESW: Link Status Changed - Port1 Link UP
ESW: Link Status Changed - Port1 Link Down
ESW: Link Status Changed - Port1 Link UP
Length of MAC:6
 mac:6c:72:20:a5:9e:f7:
----


=== pAd = c1232000, size = 960336 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6
RX DESC a25d7000  size = 2048
RTMP_TimerListAdd: add timer obj c129d638!
RTMP_TimerListAdd: add timer obj c123a23c!
RTMP_TimerListAdd: add timer obj c1239e30!
RTMP_TimerListAdd: add timer obj c123a20c!
RTMP_TimerListAdd: add timer obj c123a548!
RTMP_TimerListAdd: add timer obj c123a488!
RTMP_TimerListAdd: add timer obj c123a4b8!
RTMP_TimerListAdd: add timer obj c123d648!
RTMP_TimerListAdd: add timer obj c123d23c!
RTMP_TimerListAdd: add timer obj c123d618!
RTMP_TimerListAdd: add timer obj c123d954!
RTMP_TimerListAdd: add timer obj c123d894!
RTMP_TimerListAdd: add timer obj c123d8c4!
RTMP_TimerListAdd: add timer obj c1240a54!
RTMP_TimerListAdd: add timer obj c1240648!
RTMP_TimerListAdd: add timer obj c1240a24!
RTMP_TimerListAdd: add timer obj c1240d60!
RTMP_TimerListAdd: add timer obj c1240ca0!
RTMP_TimerListAdd: add timer obj c1240cd0!
RTMP_TimerListAdd: add timer obj c1243e60!
RTMP_TimerListAdd: add timer obj c1243a54!
RTMP_TimerListAdd: add timer obj c1243e30!
RTMP_TimerListAdd: add timer obj c124416c!
RTMP_TimerListAdd: add timer obj c12440ac!
RTMP_TimerListAdd: add timer obj c12440dc!
RTMP_TimerListAdd: add timer obj c124726c!
RTMP_TimerListAdd: add timer obj c1246e60!
RTMP_TimerListAdd: add timer obj c124723c!
RTMP_TimerListAdd: add timer obj c1247578!
RTMP_TimerListAdd: add timer obj c12474b8!
RTMP_TimerListAdd: add timer obj c12474e8!
RTMP_TimerListAdd: add timer obj c124a678!
RTMP_TimerListAdd: add timer obj c124a26c!
RTMP_TimerListAdd: add timer obj c124a648!
RTMP_TimerListAdd: add timer obj c124a984!
RTMP_TimerListAdd: add timer obj c124a8c4!
RTMP_TimerListAdd: add timer obj c124a8f4!
RTMP_TimerListAdd: add timer obj c124da84!
RTMP_TimerListAdd: add timer obj c124d678!
RTMP_TimerListAdd: add timer obj c124da54!
RTMP_TimerListAdd: add timer obj c124dd90!
RTMP_TimerListAdd: add timer obj c124dcd0!
RTMP_TimerListAdd: add timer obj c124dd00!
RTMP_TimerListAdd: add timer obj c1250e90!
RTMP_TimerListAdd: add timer obj c1250a84!
RTMP_TimerListAdd: add timer obj c1250e60!
RTMP_TimerListAdd: add timer obj c125119c!
RTMP_TimerListAdd: add timer obj c12510dc!
RTMP_TimerListAdd: add timer obj c125110c!
RTMP_TimerListAdd: add timer obj c125429c!
RTMP_TimerListAdd: add timer obj c1253e90!
RTMP_TimerListAdd: add timer obj c125426c!
RTMP_TimerListAdd: add timer obj c12545a8!
RTMP_TimerListAdd: add timer obj c12544e8!
RTMP_TimerListAdd: add timer obj c1254518!
RTMP_TimerListAdd: add timer obj c12576a8!
RTMP_TimerListAdd: add timer obj c125729c!
RTMP_TimerListAdd: add timer obj c1257678!
RTMP_TimerListAdd: add timer obj c12579b4!
RTMP_TimerListAdd: add timer obj c12578f4!
RTMP_TimerListAdd: add timer obj c1257924!
RTMP_TimerListAdd: add timer obj c125aab4!
RTMP_TimerListAdd: add timer obj c125a6a8!
RTMP_TimerListAdd: add timer obj c125aa84!
RTMP_TimerListAdd: add timer obj c125adc0!
RTMP_TimerListAdd: add timer obj c125ad00!
RTMP_TimerListAdd: add timer obj c125ad30!
RTMP_TimerListAdd: add timer obj c125dec0!
RTMP_TimerListAdd: add timer obj c125dab4!
RTMP_TimerListAdd: add timer obj c125de90!
RTMP_TimerListAdd: add timer obj c125e1cc!
RTMP_TimerListAdd: add timer obj c125e10c!
RTMP_TimerListAdd: add timer obj c125e13c!
RTMP_TimerListAdd: add timer obj c12612cc!
RTMP_TimerListAdd: add timer obj c1260ec0!
RTMP_TimerListAdd: add timer obj c126129c!
RTMP_TimerListAdd: add timer obj c12615d8!
RTMP_TimerListAdd: add timer obj c1261518!
RTMP_TimerListAdd: add timer obj c1261548!
RTMP_TimerListAdd: add timer obj c12646d8!
RTMP_TimerListAdd: add timer obj c12642cc!
RTMP_TimerListAdd: add timer obj c12646a8!
RTMP_TimerListAdd: add timer obj c12649e4!
RTMP_TimerListAdd: add timer obj c1264924!
RTMP_TimerListAdd: add timer obj c1264954!
RTMP_TimerListAdd: add timer obj c1267ae4!
RTMP_TimerListAdd: add timer obj c12676d8!
RTMP_TimerListAdd: add timer obj c1267ab4!
RTMP_TimerListAdd: add timer obj c1267df0!
RTMP_TimerListAdd: add timer obj c1267d30!
RTMP_TimerListAdd: add timer obj c1267d60!
RTMP_TimerListAdd: add timer obj c126aef0!
RTMP_TimerListAdd: add timer obj c126aae4!
RTMP_TimerListAdd: add timer obj c126aec0!
RTMP_TimerListAdd: add timer obj c126b1fc!
RTMP_TimerListAdd: add timer obj c126b13c!
RTMP_TimerListAdd: add timer obj c126b16c!
RTMP_TimerListAdd: add timer obj c1273fa4!
RTMP_TimerListAdd: add timer obj c12740c0!
RTMP_TimerListAdd: add timer obj c1273fd0!
RTMP_TimerListAdd: add timer obj c126b52c!
RTMP_TimerListAdd: add timer obj c12374cc!
RTMP_TimerListAdd: add timer obj c123a8d8!
RTMP_TimerListAdd: add timer obj c123dce4!
RTMP_TimerListAdd: add timer obj c12410f0!
RTMP_TimerListAdd: add timer obj c12444fc!
RTMP_TimerListAdd: add timer obj c1247908!
RTMP_TimerListAdd: add timer obj c124ad14!
RTMP_TimerListAdd: add timer obj c124e120!
RTMP_TimerListAdd: add timer obj c125152c!
RTMP_TimerListAdd: add timer obj c1254938!
RTMP_TimerListAdd: add timer obj c1257d44!
RTMP_TimerListAdd: add timer obj c125b150!
RTMP_TimerListAdd: add timer obj c125e55c!
RTMP_TimerListAdd: add timer obj c1261968!
RTMP_TimerListAdd: add timer obj c1264d74!
RTMP_TimerListAdd: add timer obj c1268180!
RTMP_TimerListAdd: add timer obj c126b240!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20 
E2PROM: 40 MW Power Delta= 0 
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 1, D2 = 4, CalCode = 7 !!!
RT6352_Temperature_Init : BBPR49 = 0x1
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff7
Current Temperature from BBP_R49=0xfffffff9
 TX BW Filter Calibration !!!
 RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= d, phase= 2)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 1, phase=3d)
TX IQ Calibration Done!
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c126bab4!
Main bssid = 6c:72:20:a5:9e:f7
<==== rt28xx_init, Status=0
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering forwarding state
br0: port 2(ra0) entering forwarding state
Ralink HW NAT Module Disabled
Ralink APSoC Hardware Watchdog Timer
Started WatchDog Timer.
Started WatchDog Timer. LoadVlaue: 36600 sysclk: 145000000 TIMEOUT: 60
addrconf_dad_completed 7
RTMP_TimerListAdd: add timer obj c0fc9618!
==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0xff000000, Reg-WlanFunCtrl=0xff000000
MACVersion = 0x76502000
load fw spent 0ms
RX DESC a26e4000 size = 2048
RX1 DESC a26e5000 size = 2048
ramtd_erase: addr:ff0000 len:0
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
2a:55:44:e4:05:1a:cb:eb:01:93:83:88:b2:c3:4f:8f:
50:b2:65:62:c1:a3:cb:f9:52:8e:b0:b1:79:c9:b6:97:

ramtd_write: to:ff0000 len:10
ramtd_write: to:ff0010 len:5ce
ramtd_write: to:ff0000 len:1
1. Phy Mode = 49
2. Phy Mode = 49
ext_pa_current_setting = 1
3. Phy Mode = 49
AntCfgInit: primary/secondary ant 0/1
ChipStructAssign(): RALINK6590 hook !
MCS Set = ff 00 00 00 01
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2)
Main bssid = 6c:72:20:a5:9e:f8
<==== rt28xx_init, Status=0
MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=44, HT-CentCh=46, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 42(Prim=44, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2)
0x1300 = 00064300
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
device rai0 entered promiscuous mode
br0: port 3(rai0) entering forwarding state
br0: port 3(rai0) entering forwarding state
addrconf_dad_completed 7

OpenWRT wgrało się bez problemu, testuję

Zuzia · 2018-10-25 20:21:53

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

- WiFi 2.4 i 5 GHz w porządku
- brak komunikacji przez LAN gigabit i WAN

logread
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    0.000000] Linux version 4.14.78 (krolik@ubuntu-VirtualBox) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6894+972-547042398a)) #0 Wed Oct 24 12:18:20 2018
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Board has DDR2
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Analog PMU set to hw control
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Digital PMU set to hw control
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] bootconsole [early0] enabled
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] MIPS: machine is D-Link DWR-118 A1
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Determined physical RAM map:
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000]  memory: 04000000 @ 00000000 (usable)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Zone ranges:
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Movable zone start for each node
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Early memory node ranges
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000] On node 0 totalpages: 16384
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 80483730, node_mem_map 81000040
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000]   Normal zone: 128 pages used for memmap
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Writing ErrCtl register=0006f880
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Readback ErrCtl register=0006f880
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] Memory: 59860K/65536K available (3611K kernel code, 172K rwdata, 840K rodata, 168K init, 207K bss, 5676K reserved, 0K cma-reserved)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] NR_IRQS: 256
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] CPU Clock: 580MHz
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] systick: enable autosleep mode
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] systick: running - mult: 214748, shift: 32
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.015470] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.087699] pid_max: default: 32768 minimum: 301
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.097089] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.110106] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.129737] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.149218] futex hash table entries: 256 (order: -1, 3072 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.161383] pinctrl core: initialized pinctrl subsystem
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.172210] NET: Registered protocol family 16
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.442174] PCI host bridge /pcie@10140000 ranges:
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.451558]  MEM 0x0000000020000000..0x000000002fffffff
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.461939]   IO 0x0000000010160000..0x000000001016ffff
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.490099] rt2880_gpio 10000600.gpio: registering 24 gpios
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.501132] rt2880_gpio 10000600.gpio: registering 24 irq handlers
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.513702] rt2880_gpio 10000638.gpio: registering 16 gpios
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.524702] rt2880_gpio 10000638.gpio: registering 16 irq handlers
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.537272] rt2880_gpio 10000660.gpio: registering 32 gpios
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.548272] rt2880_gpio 10000660.gpio: registering 32 irq handlers
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.560826] rt2880_gpio 10000688.gpio: registering 1 gpios
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.571647] rt2880_gpio 10000688.gpio: registering 1 irq handlers
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.584518] PCI host bridge to bus 0000:00
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.592514] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.606229] pci_bus 0000:00: root bus resource [io  0xffffffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.617958] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.631458] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.647245] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.647284] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.647298] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.647369] pci 0000:00:00.0: supports D1
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.647379] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.647649] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.663652] pci 0000:01:00.0: [14c3:7650] type 00 class 0x028000
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.663700] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.663834] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.664075] pci 0000:01:00.1: [14c3:8650] type 00 class 0x0d1100
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.664117] pci 0000:01:00.1: reg 0x10: [mem 0x00000000-0x000fffff]
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.664242] pci 0000:01:00.1: supports D1
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.664252] pci 0000:01:00.1: PME# supported from D0 D1 D3hot D3cold
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.664446] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.664463] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.664512] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.677567] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.691375] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.704875] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.718385] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.731880] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.745378] pci 0000:00:00.0: PCI bridge to [bus 01]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.755229] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.773871] clocksource: Switched to clocksource systick
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.785468] NET: Registered protocol family 2
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.794862] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.808636] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.821225] TCP: Hash tables configured (established 1024 bind 1024)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.834039] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.845544] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.858220] NET: Registered protocol family 1
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    0.866834] PCI: CLS 0 bytes, default 32
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.869558] rt-timer 10000100.timer: maximum frequency is 1220Hz
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    0.882262] Crashlog allocated RAM at address 0x3f00000
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.894343] workingset: timestamp_bits=30 max_order=14 bucket_order=0
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.912269] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.923766] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.953122] io scheduler noop registered
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.960827] io scheduler deadline registered (default)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.971800] gpio-export gpio_export: 1 gpio(s) exported
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.982356] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
Thu Oct 25 18:09:36 2018 kern.info kernel: [    0.995962] console [ttyS0] disabled
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.002953] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.022729] console [ttyS0] enabled
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.036497] bootconsole [early0] disabled
Thu Oct 25 18:09:36 2018 kern.err kernel: [    1.052930] cacheinfo: Failed to find cpu0 device node
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    1.063198] cacheinfo: Unable to detect cache hierarchy for CPU 0
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    1.080097] spi spi0.0: force spi mode3
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.099134] m25p80 spi0.0: w25q128 (16384 Kbytes)
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.108562] 3 fixed-partitions partitions found on MTD device spi0.0
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.121221] Creating 3 MTD partitions on "spi0.0":
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.130772] 0x000000000000-0x000000010000 : "jboot"
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.141363] 0x000000010000-0x000000ff0000 : "firmware"
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.154039] 2 jimage-fw partitions found on MTD device firmware
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.165874] 0x000000010000-0x00000018c297 : "kernel"
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.176672] 0x00000018c297-0x000000ff0000 : "rootfs"
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.187355] mtd: device 3 (rootfs) set to be root filesystem
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.200131] 1 squashfs-split partitions found on MTD device rootfs
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.212513] 0x0000003b6000-0x000000ff0000 : "rootfs_data"
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    1.224208] 0x000000ff0000-0x000001000000 : "config"
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.235607] libphy: Fixed MDIO Bus: probed
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.252783] gsw: setting port4 to gmac mode
Thu Oct 25 18:09:36 2018 kern.err kernel: [    1.261211] mtk_soc_eth 10100000.ethernet: generated random MAC address de:65:c8:51:36:17
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.277685] libphy: mdio: probed
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.319317] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=02430d91, driver=ICPlus IP1001]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.373867] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=02430d91, driver=ICPlus IP1001]
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.395275] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.407712] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.424711] rt2880_wdt 10000120.watchdog: Initialized
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.436002] NET: Registered protocol family 10
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.448515] Segment Routing with IPv6
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.455982] NET: Registered protocol family 17
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.464899] 8021q: 802.1Q VLAN Support v1.8
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.479745] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Thu Oct 25 18:09:36 2018 kern.info kernel: [    1.494772] Freeing unused kernel memory: 168K
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    1.503651] This architecture does not have kernel memory protection.
Thu Oct 25 18:09:36 2018 user.info kernel: [    2.391582] init: Console is alive
Thu Oct 25 18:09:36 2018 user.info kernel: [    2.398691] init: - watchdog -
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    2.593626] random: fast init done
Thu Oct 25 18:09:36 2018 user.info kernel: [    3.597361] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.746497] usbcore: registered new interface driver usbfs
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.757590] usbcore: registered new interface driver hub
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.768321] usbcore: registered new device driver usb
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.784468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.799260] ehci-platform: EHCI generic platform driver
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.820063] phy phy-usbphy.0: remote usb device wakeup disabled
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.831863] phy phy-usbphy.0: UTMI 16bit 30MHz
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.840730] ehci-platform 101c0000.ehci: EHCI Host Controller
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.852210] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.868120] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.888553] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.902001] hub 1-0:1.0: USB hub found
Thu Oct 25 18:09:36 2018 kern.info kernel: [    3.909915] hub 1-0:1.0: 1 port detected
Thu Oct 25 18:09:36 2018 user.info kernel: [    3.922520] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Thu Oct 25 18:09:36 2018 user.info kernel: [    3.941071] init: - preinit -
Thu Oct 25 18:09:36 2018 kern.info kernel: [    4.597169] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    4.865220] random: procd: uninitialized urandom read (4 bytes read)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    5.191290] 8021q: adding VLAN 0 to HW filter on device eth0
Thu Oct 25 18:09:36 2018 kern.info kernel: [    5.592405] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex)
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    7.016853] jffs2: notice: (397) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 6 orphan) and 6 of xref (6 dead, 0 orphan) found.
Thu Oct 25 18:09:36 2018 user.info kernel: [    7.050008] mount_root: switching to jffs2 overlay
Thu Oct 25 18:09:36 2018 kern.warn kernel: [    7.090120] overlayfs: upper fs does not support tmpfile.
Thu Oct 25 18:09:36 2018 user.warn kernel: [    7.107016] urandom-seed: Seeding with /etc/urandom.seed
Thu Oct 25 18:09:36 2018 user.info kernel: [    7.236686] procd: - early -
Thu Oct 25 18:09:36 2018 user.info kernel: [    7.243367] procd: - watchdog -
Thu Oct 25 18:09:36 2018 kern.info kernel: [    7.460340] mtk_soc_eth 10100000.ethernet eth0: port 5 link down
Thu Oct 25 18:09:36 2018 user.info kernel: [    7.846538] procd: - watchdog -
Thu Oct 25 18:09:36 2018 user.info kernel: [    7.853164] procd: - ubus -
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    7.943936] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    7.989677] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Oct 25 18:09:36 2018 kern.notice kernel: [    8.003446] random: ubusd: uninitialized urandom read (4 bytes read)
Thu Oct 25 18:09:36 2018 user.info kernel: [    8.017106] procd: - init -
Thu Oct 25 18:09:36 2018 user.info kernel: [    8.443191] kmodloader: loading kernel modules from /etc/modules.d/*
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.462582] ip6_tables: (C) 2000-2006 Netfilter Core Team
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.487231] usbcore: registered new interface driver cdc_wdm
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.500353] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.515659] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.533299] ip_tables: (C) 2000-2006 Netfilter Core Team
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.553465] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.638386] xt_time: kernel timezone is -0000
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.725861] PPP generic driver version 2.4.2
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.737242] NET: Registered protocol family 24
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.749058] usbcore: registered new interface driver qmi_wwan
Thu Oct 25 18:09:36 2018 kern.err kernel: [    8.777056] mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.789622] mt76x0e 0000:01:00.0: ASIC revision: 76100002
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.879486] mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
Thu Oct 25 18:09:36 2018 kern.info kernel: [    8.974460] mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    8.988649] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Thu Oct 25 18:09:36 2018 kern.info kernel: [    9.035900] ieee80211 phy1: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
Thu Oct 25 18:09:36 2018 kern.info kernel: [    9.132944] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
Thu Oct 25 18:09:36 2018 kern.info kernel: [    9.148466] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
Thu Oct 25 18:09:36 2018 kern.debug kernel: [    9.162852] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Thu Oct 25 18:09:36 2018 user.info kernel: [    9.171908] kmodloader: done loading kernel modules from /etc/modules.d/*
Thu Oct 25 18:09:36 2018 kern.warn kernel: [   10.255250] urandom_read: 5 callbacks suppressed
Thu Oct 25 18:09:36 2018 kern.notice kernel: [   10.255260] random: jshn: uninitialized urandom read (4 bytes read)
Thu Oct 25 18:09:37 2018 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Thu Oct 25 18:09:37 2018 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: started, version 2.80 cachesize 150
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: DNS service limited to local subnets
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain test
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain onion
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain localhost
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain local
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain invalid
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain bind
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: using local addresses only for domain lan
Thu Oct 25 18:09:37 2018 daemon.warn dnsmasq[754]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: read /etc/hosts - 4 addresses
Thu Oct 25 18:09:37 2018 daemon.info dnsmasq[754]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: 8021ad
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: 8021q
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: macvlan
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: veth
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: bridge
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: Network device
Thu Oct 25 18:09:39 2018 user.notice : Added device handler type: tunnel
Thu Oct 25 18:09:39 2018 daemon.notice procd: /etc/init.d/network: 'radio0' is disabled
Thu Oct 25 18:09:39 2018 daemon.notice procd: /etc/init.d/network: 'radio1' is disabled
Thu Oct 25 18:09:39 2018 daemon.notice procd: /etc/init.d/network: 'radio0' is disabled
Thu Oct 25 18:09:39 2018 daemon.notice procd: /etc/init.d/network: 'radio1' is disabled
Thu Oct 25 18:09:41 2018 authpriv.info dropbear[900]: Not backgrounding
Thu Oct 25 18:09:41 2018 daemon.notice procd: /etc/rc.d/S96led: setting up led lan
Thu Oct 25 18:09:41 2018 daemon.notice procd: /etc/rc.d/S96led: setting up led wan
Thu Oct 25 18:09:41 2018 daemon.notice procd: /etc/rc.d/S96led: setting up led wifi
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.286677] 8021q: adding VLAN 0 to HW filter on device eth0
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.298513] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (100Mbps/Full duplex)
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.334414] device eth0 entered promiscuous mode
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.362488] br-lan: port 1(eth0.1) entered blocking state
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.373325] br-lan: port 1(eth0.1) entered disabled state
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.384481] device eth0.1 entered promiscuous mode
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.445483] br-lan: port 1(eth0.1) entered blocking state
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.456309] br-lan: port 1(eth0.1) entered forwarding state
Thu Oct 25 18:09:43 2018 kern.info kernel: [   17.467622] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'lan' is enabled
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'lan' is setting up now
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'lan' is now up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'loopback' is enabled
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'loopback' is now up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'wan' is enabled
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'wan6' is enabled
Thu Oct 25 18:09:43 2018 daemon.notice netifd: bridge 'br-lan' link is up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Network device 'eth0' link is up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: VLAN 'eth0.1' link is up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Network device 'lo' link is up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Oct 25 18:09:43 2018 daemon.notice netifd: VLAN 'eth0.2' link is up
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'wan6' has link connectivity
Thu Oct 25 18:09:43 2018 daemon.notice netifd: Interface 'wan6' is setting up now
Thu Oct 25 18:09:44 2018 daemon.notice netifd: wan (1053): udhcpc: started, v1.29.3
Thu Oct 25 18:09:44 2018 daemon.err odhcp6c[1058]: Failed to send RS (Address not available)
Thu Oct 25 18:09:44 2018 kern.info kernel: [   18.314313] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu Oct 25 18:09:44 2018 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Oct 25 18:09:44 2018 daemon.notice netifd: wan (1053): udhcpc: sending discover
Thu Oct 25 18:09:44 2018 daemon.info procd: - init complete -
Thu Oct 25 18:09:45 2018 kern.info kernel: [   19.434303] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex)
Thu Oct 25 18:09:47 2018 daemon.notice netifd: wan (1053): udhcpc: sending discover
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[754]: exiting on receipt of SIGTERM
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: started, version 2.80 cachesize 150
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: DNS service limited to local subnets
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq-dhcp[1199]: DHCP, IP range 192.168.3.100 -- 192.168.3.249, lease time 12h
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain test
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain onion
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain localhost
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain local
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain invalid
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain bind
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: using local addresses only for domain lan
Thu Oct 25 18:09:49 2018 daemon.warn dnsmasq[1199]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: read /etc/hosts - 4 addresses
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq-dhcp[1199]: read /etc/ethers - 0 addresses
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: read /etc/hosts - 4 addresses
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq[1199]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Thu Oct 25 18:09:49 2018 daemon.info dnsmasq-dhcp[1199]: read /etc/ethers - 0 addresses
Thu Oct 25 18:09:50 2018 daemon.notice netifd: wan (1053): udhcpc: sending discover
Thu Oct 25 18:11:30 2018 kern.notice kernel: [   55.146536] random: crng init done

Królik · 2018-10-25 20:33:46

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

I bądź tu człowieku mądry...
U mnie działają oba gigabity. A przecież oboje mamy tą samą wersję hardware i bliźniacze partycje config.

Wpięcie i wypięcie wtyczki powoduje jakiekolwiek zmiany w logu?

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-25 20:48:48

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Wykrywa, wpinam LAN i WAN:

Thu Oct 25 17:27:22 2018 kern.info kernel: [  347.665503] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
Thu Oct 25 17:27:23 2018 kern.info kernel: [  348.024350] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (100Mbps/Full duplex)
Thu Oct 25 17:27:24 2018 daemon.notice netifd: wan (1551): udhcpc: sending discover
Thu Oct 25 17:27:27 2018 daemon.notice netifd: wan (1551): udhcpc: sending discover

Konfiguracja wygląda na dobrą:

ifconfig
br-lan    Link encap:Ethernet  HWaddr 6C:72:20:A5:9E:F7  
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::6e72:20ff:fea5:9ef7/64 Scope:Link
          inet6 addr: fdf2:3449:e498::1/60 Scope:Global
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1030 (1.0 KiB)  TX bytes:4488 (4.3 KiB)

eth0      Link encap:Ethernet  HWaddr 1A:26:FC:F9:64:6B  
          inet6 addr: fe80::1826:fcff:fef9:646b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:268 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1102 (1.0 KiB)  TX bytes:74839 (73.0 KiB)
          Interrupt:5 

eth0.1    Link encap:Ethernet  HWaddr 6C:72:20:A5:9E:F7  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4 errors:0 dropped:0 overruns:0 frame:0
          TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1030 (1.0 KiB)  TX bytes:3874 (3.7 KiB)

eth0.2    Link encap:Ethernet  HWaddr 6C:72:20:A5:9E:F6  
          inet6 addr: fe80::6e72:20ff:fea5:9ef6/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:224 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:66838 (65.2 KiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:160 errors:0 dropped:0 overruns:0 frame:0
          TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:10880 (10.6 KiB)  TX bytes:10880 (10.6 KiB)

root@OpenWrt:/# cat /etc/config/network

config interface 'loopback'
    option ifname 'lo'
    option proto 'static'
    option ipaddr '127.0.0.1'
    option netmask '255.0.0.0'

config globals 'globals'
    option ula_prefix 'fdf2:3449:e498::/48'

config interface 'lan'
    option type 'bridge'
    option ifname 'eth0.1'
    option proto 'static'
    option ipaddr '192.168.1.1'
    option netmask '255.255.255.0'
    option ip6assign '60'

config device 'lan_dev'
    option name 'eth0.1'
    option macaddr '6c:72:20:a5:9e:f7'

config interface 'wan'
    option ifname 'eth0.2'
    option proto 'dhcp'

config device 'wan_dev'
    option name 'eth0.2'
    option macaddr '6c:72:20:a5:9e:f6'

config interface 'wan6'
    option ifname 'eth0.2'
    option proto 'dhcpv6'

config switch
    option name 'switch0'
    option reset '1'
    option enable_vlan '1'

config switch_vlan
    option device 'switch0'
    option vlan '1'
    option ports '1 2 3 4 6t'

config switch_vlan
    option device 'switch0'
    option vlan '2'
    option ports '5 6t'


root@OpenWrt:/# cat /etc/config/firewall
config defaults
    option syn_flood    1
    option input        ACCEPT
    option output        ACCEPT
    option forward        REJECT
# Uncomment this line to disable ipv6 rules
#    option disable_ipv6    1

config zone
    option name        lan
    list   network        'lan'
    option input        ACCEPT
    option output        ACCEPT
    option forward        ACCEPT

config zone
    option name        wan
    list   network        'wan'
    list   network        'wan6'
    option input        REJECT
    option output        ACCEPT
    option forward        REJECT
    option masq        1
    option mtu_fix        1

config forwarding
    option src        lan
    option dest        wan

# We need to accept udp packets on port 68,
# see https://dev.openwrt.org/ticket/4108
config rule
    option name        Allow-DHCP-Renew
    option src        wan
    option proto        udp
    option dest_port    68
    option target        ACCEPT
    option family        ipv4

# Allow IPv4 ping
config rule
    option name        Allow-Ping
    option src        wan
    option proto        icmp
    option icmp_type    echo-request
    option family        ipv4
    option target        ACCEPT

config rule
    option name        Allow-IGMP
    option src        wan
    option proto        igmp
    option family        ipv4
    option target        ACCEPT

# Allow DHCPv6 replies
# see https://dev.openwrt.org/ticket/10381
config rule
    option name        Allow-DHCPv6
    option src        wan
    option proto        udp
    option src_ip        fc00::/6
    option dest_ip        fc00::/6
    option dest_port    546
    option family        ipv6
    option target        ACCEPT

config rule
    option name        Allow-MLD
    option src        wan
    option proto        icmp
    option src_ip        fe80::/10
    list icmp_type        '130/0'
    list icmp_type        '131/0'
    list icmp_type        '132/0'
    list icmp_type        '143/0'
    option family        ipv6
    option target        ACCEPT

# Allow essential incoming IPv6 ICMP traffic
config rule
    option name        Allow-ICMPv6-Input
    option src        wan
    option proto    icmp
    list icmp_type        echo-request
    list icmp_type        echo-reply
    list icmp_type        destination-unreachable
    list icmp_type        packet-too-big
    list icmp_type        time-exceeded
    list icmp_type        bad-header
    list icmp_type        unknown-header-type
    list icmp_type        router-solicitation
    list icmp_type        neighbour-solicitation
    list icmp_type        router-advertisement
    list icmp_type        neighbour-advertisement
    option limit        1000/sec
    option family        ipv6
    option target        ACCEPT

# Allow essential forwarded IPv6 ICMP traffic
config rule
    option name        Allow-ICMPv6-Forward
    option src        wan
    option dest        *
    option proto        icmp
    list icmp_type        echo-request
    list icmp_type        echo-reply
    list icmp_type        destination-unreachable
    list icmp_type        packet-too-big
    list icmp_type        time-exceeded
    list icmp_type        bad-header
    list icmp_type        unknown-header-type
    option limit        1000/sec
    option family        ipv6
    option target        ACCEPT

config rule
    option name        Allow-IPSec-ESP
    option src        wan
    option dest        lan
    option proto        esp
    option target        ACCEPT

config rule
    option name        Allow-ISAKMP
    option src        wan
    option dest        lan
    option dest_port    500
    option proto        udp
    option target        ACCEPT

Zuzia · 2018-10-25 21:19:45

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Chyba już wiem co go boli. Udało się zestawić połączenie na WAN pomiędzy oboma gigabitami, wtedy pobiera adres DHCP prawidłowo:

Thu Oct 25 17:39:42 2018 kern.info kernel: [  602.360345] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (1000Mbps/Full duplex)
Thu Oct 25 17:39:42 2018 daemon.notice netifd: wan (2225): udhcpc: started, v1.29.3
Thu Oct 25 17:39:42 2018 daemon.err odhcp6c[2227]: Failed to send RS (Address not available)
Thu Oct 25 17:39:42 2018 daemon.notice netifd: wan (2225): udhcpc: sending discover
Thu Oct 25 17:39:42 2018 daemon.notice netifd: wan (2225): udhcpc: sending select for 192.168.1.103
Thu Oct 25 17:39:42 2018 daemon.notice netifd: wan (2225): udhcpc: lease of 192.168.1.103 obtained, lease time 7165
Thu Oct 25 17:39:42 2018 daemon.notice netifd: Interface 'wan' is now up
Thu Oct 25 17:39:42 2018 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)

Niestety WAN nie chce działać z niczym innym poza gigabitem po drugiej stronie. Sprawdzałam z dwoma starszymi routerami i nie pobiera adresu. Zrestartowałam i LAN gigabit podłączony do komputera z kartą gigabit ruszył.

Wnioski: WAN i LAN gigabit niestety odmawia współpracy z urządzeniami 100 Mbps. Może coś popsuli w tej wersji OpenWRT?

Królik · 2018-10-25 21:25:56

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Może być jakiś problem konfiguracją drivera. Będę kminić o co chodzi.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-25 21:30:43

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Testowałam na routerze Easybox, DWR-118 A2 i karcie Tp-Linka. Może też spróbuj z czymś na 100 Mbps.

Edycja:
Połączyłam z ciekawości kablem krosowanym, ale bez zmian, link jest tylko komunikacji brak na WAN. Przy okazji zauważyłam, że A1 bardzo się grzeje, A2 jest ledwo ciepły. Chyba trzeba do A1 dać radiatorek.

Królik · 2018-10-26 06:35:40

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Być może mam źle przygotowany wpis w dts dla tego PHY. Tutaj też był z nim problem, pewnie i u nas jakieś timingi są nie halo.

https://github.com/openwrt/openwrt/comm … c78d3a42a4

Po pracy sprawdzę czy to to.

EDIT:

Te PHY gigabitowe są niestety wyjątkowo ciepłe.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Cezary · 2018-10-26 06:38:22

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,105

Odp: D-Link DWR 118

Lekko OT: ja tak miałem na jednym z atherosów - źle ustawione wartości w rejestrach od pll powodowały że działało tylko na 1Gbps a nie chciało na 100. Bity od rx/tx delay był do zmiany.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Królik · 2018-10-26 17:24:36

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Sprawdź ten soft:

https://www.dropbox.com/s/drlfqna0908w4 … y.bin?dl=0
https://www.dropbox.com/s/e36aeuo3ah05b … e.bin?dl=0

U mnie nie działała setka tylko na GELAN, na nowym sofcie jest ok. Ustawiłem opóźnienia dla obu PHY.

Mam nadzieję, że i u Ciebie będzie spoko.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-26 17:54:15

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Jest dobrze na obydwu gigabitach

Królik · 2018-10-26 17:57:56

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Zaraz poleci PR.

Natchnęło mnie za to na gigabit w A2. Normalnie PHY Marvella konfiguruje u-Boot. J-BOOT niektórych rzeczy w ogóle nie konfigurował, nie zdziwię się jak w tym przypadku jest to samo. Oby to było to. Jak zadziała to się pochwalę.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-26 18:02:51

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Relacjonuj na bieżąco

A1 na razie nie jest moim faworytem, przy zamkniętej obudowie grzeje się tak, że czuć zapach topionego plastiku. Nie wróży to długiej żywotności. Zastanawiam się, czy jest sens przyklejać radiatory takie małe jak na kości pamięci, bo mój egzemplarz jest jeszcze na gwarancji i nie wiadomo, czy w razie czego serwis nie przyczepi się...

Królik · 2018-10-26 18:08:02

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

https://github.com/openwrt/openwrt/pull/1499 -> poszedł

Zaletą DWRów 118 jest tanie ac i popularność, którą DWR-11x zawdzięczają operatorom.
Jeśli nawet upali się PHY, to spokojnie możesz wrócić do OFW (pozostałe powinny działać) i wysłać na gwarancję.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-26 18:16:48

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Co do popularności to Play i T-Mobile dużo tego wepchneli klientom więc spodziewam się, że sporo osób doceni Twoją pracę
Ciekawe, kiedy dołączą do repo.

Królik · 2018-10-26 18:19:35

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

DWR-116 dało się wyrwać za 30zł z przesyłką. 118 też pewnie nie będzie trzymać ceny.

Wszystko zależy od tego, jak bardzo M. Kresin jest zawalony robotą.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-26 18:22:33

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Zawsze gubię się na githubie. Masz link do patcha? Chcę sobie zrobić już własny obraz

Cezary · 2018-10-26 18:32:43

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,105

Odp: D-Link DWR 118

Zuzia napisał/a:

Zawsze gubię się na githubie. Masz link do patcha? Chcę sobie zrobić już własny obraz

Dodaj .patch na końcu tego adresu

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Zuzia · 2018-10-26 18:39:33

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Dzięki, ale gapa ze mnie

@Królik
Dziękuję za wszystko, nie spodziewałam się, że tak szybko powstanie pełnowartościowe OpenWRT pod ten model. Postanowiłam nakleić radiatorki i używać A1 zamiast A2

Zuzia · 2018-10-28 10:12:10

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Niestety pojawiły się problemy, średnio po kilku godzinach pracy na modemie LTE rozłącza:

Sun Oct 28 03:08:38 2018 daemon.info procd: - init complete -
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.173868] ------------[ cut here ]------------
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.183098] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274
Sun Oct 28 07:41:12 2018 kern.info kernel: [10412.199578] NETDEV WATCHDOG: eth1 (cdc_ether): transmit queue 0 timed out
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.213105] Modules linked in: rt2800soc rt2800pci rt2800mmio rt2800lib pppoe ppp_async option mt76x0e mt76x0_common cdc_mbim usb_wwan sierra_net sierra rt2x00soc rt2x00pci rt2x00mmio rt2x00lib rndis_host qmi_wwan pptp pppox ppp_mppe ppp_generic nf_nat_pptp nf_conntrack_pptp nf_conntrack_ipv6 mt76x2e mt76x2_common mt76x02_lib mt7603e mt76 mac80211 kalmia iptable_nat ipt_REJECT ipt_MASQUERADE huawei_cdc_ncm cfg80211 cdc_ncm cdc_ether xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY usbserial usbnet usblp ums_usbat ums_sddr55 ums_sddr09 ums_karma ums_jumpshot ums_isd200
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.354088]  ums_freecom ums_datafab ums_cypress ums_alauda ts_fsm ts_bm slhc nf_reject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_rtsp nf_nat_redirect nf_nat_proto_gre nf_nat_masquerade_ipv4 nf_nat_irc nf_conntrack_ipv4 nf_nat_ipv4 nf_nat_h323 nf_nat_ftp nf_nat_amanda nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip nf_conntrack_rtsp nf_conntrack_rtcache nf_conntrack_proto_gre nf_conntrack_netlink nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp nf_conntrack_broadcast ts_kmp nf_conntrack_amanda nf_conntrack libcrc32c iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables hso crc_itu_t crc_ccitt compat cdc_wdm cdc_acm ledtrig_usbport xt_set ip_set_list_set ip_set_hash_netiface ip_set_hash_netport
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.494837]  ip_set_hash_netnet ip_set_hash_net ip_set_hash_netportnet ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables ip_gre gre ip_tunnel loop vfat fat ntfs autofs4 fscache nls_utf8 nls_iso8859_1 nls_cp437 eeprom_93cx6 sha1_generic ecb uas usb_storage leds_gpio ohci_platform ohci_hcd ehci_platform sd_mod scsi_mod ehci_hcd gpio_button_hotplug f2fs ext4 jbd2 mbcache usbcore nls_base usb_common crc16 mii aead crypto_null crc32c_generic cryptomgr crc32_generic crypto_hash
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.619846] CPU: 0 PID: 0 Comm: swapper Not tainted 4.14.78 #0
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.631465] Stack : 80490000 8043d584 00000000 00000000 80417bbc 83809e34 80467cec 80467907
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.648124]         80413f78 00000000 804c3660 00000140 8047b9d4 00000001 83809de8 532616af
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.664781]         00000000 00000000 804c0000 00006b90 00000000 00000139 00000007 00000000
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.681438]         00000000 80470000 00097546 00000000 00000000 00000000 804379c8 8029bbcc
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.698095]         00000009 00000140 8047b9d4 8047b994 00000001 801fb290 00000000 804c0000
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.714755]         ...
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.719614] Call Trace:
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.724512] [<8000edec>] show_stack+0x58/0x100
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.733376] [<80025d00>] __warn+0xe4/0x118
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.741551] [<80025d64>] warn_slowpath_fmt+0x30/0x3c
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.751447] [<8029bbcc>] dev_watchdog+0x164/0x274
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.760838] [<8005f0c0>] call_timer_fn.isra.4+0x24/0x84
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.771252] [<8005f294>] run_timer_softirq+0x174/0x1ec
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.781500] [<8038a118>] __do_softirq+0xe8/0x2bc
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.790708] [<80009df8>] handle_int+0x138/0x144
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.799736] [<8000b8ec>] r4k_wait_irqoff+0x18/0x24
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.809286] [<8004dbd0>] do_idle+0x78/0xe4
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.817447] [<8004de28>] cpu_startup_entry+0x18/0x20
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.827347] [<8048cbc0>] start_kernel+0x454/0x474
Sun Oct 28 07:41:12 2018 kern.warn kernel: [10412.836721] ---[ end trace 6d15995e47dc22c9 ]---
Sun Oct 28 07:45:16 2018 daemon.info watchcat[7676]: no internet connectivity for 1080 seconds. Reseting when reaching 21600

Robię nowy obraz z włączonym debugowaniem może coś więcej będzie w logu.

Królik · 2018-10-28 10:46:23

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Wygląda jakby coś się zawieszało. To w trybie hilink? Na innych modemach jest to samo?

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-28 10:49:04

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

To jest E3372 hilink i na A2 działa doskonale.

Królik · 2018-10-28 10:52:11

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Na tym samym snapshocie?

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

Zuzia · 2018-10-28 10:57:52

Zuzia
Użytkownik
Nieaktywny

Zarejestrowany: 2015-01-10
Posty: 826

Odp: D-Link DWR 118

Na A1 mam r8381-4056be58f3m, na A2 r8247-90bb790fbf. Jeszcze nie spotkałam się z wersją, która popsułaby pracę E3372h z A2. Oczywiście sprawdzę to i dam znać.

Królik · 2018-10-28 11:01:28

Królik
Użytkownik
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2015-07-10
Posty: 1,106

Odp: D-Link DWR 118

Ciężko stwierdzić w tym momencie co może być przyczyną. Gdzieś widziałem narzekania na stabilność usb w DWR-ach.

Mam i używam: Fujitsu Futro S720, Netgear R6220, Unielec U7621-06, TP-Linki 1043 V1, V2, Linksysy EA7500v2, AeroHive AP350, Linksys EA8500, ZTE MF286d.
Mam: D-Linki DWR-921, DWR-118, DWR-116, TP-Link WDR-4900 v1, Checkpoint L-50, Linksysy 1900ACS, LB-Link BL-W1200,

FAQ o OpenWrt | Sprzedam różne routery | Oddam

D-Link DWR 118 (Strona 8 z 14)

Posty: 176 do 200 z 342

176 Odpowiedź przez Zuzia 2018-10-25 19:17:12

Odp: D-Link DWR 118

177 Odpowiedź przez Zuzia 2018-10-25 20:21:53

Odp: D-Link DWR 118

178 Odpowiedź przez Królik 2018-10-25 20:33:46 (edytowany przez Królik 2018-10-25 20:34:36)

Odp: D-Link DWR 118

179 Odpowiedź przez Zuzia 2018-10-25 20:48:48

Odp: D-Link DWR 118

180 Odpowiedź przez Zuzia 2018-10-25 21:19:45 (edytowany przez Zuzia 2018-10-25 21:20:10)

Odp: D-Link DWR 118

181 Odpowiedź przez Królik 2018-10-25 21:25:56

Odp: D-Link DWR 118

182 Odpowiedź przez Zuzia 2018-10-25 21:30:43 (edytowany przez Zuzia 2018-10-26 00:35:46)

Odp: D-Link DWR 118

183 Odpowiedź przez Królik 2018-10-26 06:35:40 (edytowany przez Królik 2018-10-26 06:36:09)

Odp: D-Link DWR 118

184 Odpowiedź przez Cezary 2018-10-26 06:38:22

Odp: D-Link DWR 118

185 Odpowiedź przez Królik 2018-10-26 17:24:36

Odp: D-Link DWR 118

186 Odpowiedź przez Zuzia 2018-10-26 17:54:15

Odp: D-Link DWR 118

187 Odpowiedź przez Królik 2018-10-26 17:57:56

Odp: D-Link DWR 118

188 Odpowiedź przez Zuzia 2018-10-26 18:02:51

Odp: D-Link DWR 118

189 Odpowiedź przez Królik 2018-10-26 18:08:02

Odp: D-Link DWR 118

190 Odpowiedź przez Zuzia 2018-10-26 18:16:48

Odp: D-Link DWR 118

191 Odpowiedź przez Królik 2018-10-26 18:19:35

Odp: D-Link DWR 118

192 Odpowiedź przez Zuzia 2018-10-26 18:22:33 (edytowany przez Zuzia 2018-10-26 18:25:26)

Odp: D-Link DWR 118

193 Odpowiedź przez Cezary 2018-10-26 18:32:43

Odp: D-Link DWR 118

194 Odpowiedź przez Zuzia 2018-10-26 18:39:33 (edytowany przez Zuzia 2020-08-04 00:29:47)

Odp: D-Link DWR 118

195 Odpowiedź przez Zuzia 2018-10-28 10:12:10 (edytowany przez Zuzia 2018-10-28 10:43:59)

Odp: D-Link DWR 118

196 Odpowiedź przez Królik 2018-10-28 10:46:23

Odp: D-Link DWR 118

197 Odpowiedź przez Zuzia 2018-10-28 10:49:04

Odp: D-Link DWR 118

198 Odpowiedź przez Królik 2018-10-28 10:52:11

Odp: D-Link DWR 118

199 Odpowiedź przez Zuzia 2018-10-28 10:57:52

Odp: D-Link DWR 118

200 Odpowiedź przez Królik 2018-10-28 11:01:28

Odp: D-Link DWR 118

Posty: 176 do 200 z 342