• Zarejestrowany: 2018-03-11
  • Posty: 14

Temat: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Witam serdecznie,
mój pierwszy temat na tym forum dużo czytałem FAQ oraz podręczników na forum i męczę się ze zainstalowaniem dvbt.
Router 1043nd v1, dvbt Omega it9135.
załadowałem
insmod input-core
insmod rc-core
insmod dvb-core
insmod dvb_usb_v2
insmod it913x
insmod rc-it913x-v1
insmod rc-it913x-v2
insmod dvb-usb-af9035

tvheadend nie widzi modułu.

dmeseg
[   41.383174] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   41.485421] device wlan0 entered promiscuous mode
[   43.320354] it913x: Unknown symbol regmap_write (err 0)
[   43.325964] it913x: Unknown symbol __regmap_init_i2c (err 0)
[   43.331902] it913x: Unknown symbol regmap_read (err 0)
[   43.337240] it913x: Unknown symbol regmap_bulk_write (err 0)
[   43.343121] it913x: Unknown symbol regmap_bulk_read (err 0)
[   43.348897] it913x: Unknown symbol regmap_exit (err 0)
[   43.553436] usb 1-1.1: dvb_usb_af9035: prechip_version=83 chip_version=01 chip_type=9135
[   43.579829] usb 1-1.1: dvb_usb_v2: found a 'ITE 9135 Generic' in warm state
[   43.610696] usb 1-1.1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
[   43.621819] DVB: registering new adapter (ITE 9135 Generic)
[   43.655079] usbcore: registered new interface driver dvb_usb_af9035
[   44.269637] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   44.276300] br-lan: port 2(wlan0) entered forwarding state
[   44.281912] br-lan: port 2(wlan0) entered forwarding state
[   46.279752] br-lan: port 2(wlan0) entered forwarding state
[  137.007862] TCP: request_sock_TCP: Possible SYN flooding on port 9981. Sending cookies.  Check SNMP counters.
[  311.144564] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
Może pomożecie ?

2 Odpowiedź przez mar_w (edytowany przez mar_w 2018-03-11 22:17:18)

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

regmap-y nie masz załadowane.

# opkg update
# opkg install kmod-i2c-core kmod-input-core kmod-regmap
Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

3 Odpowiedź przez ad2014

  • ad2014
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-07-04
  • Posty: 1,142

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

i być  może  jeszcze     kmod-i2c-mux 
sprawdzamy zaleznosci 

     
strings /lib/modules/3.18.27/e4000.ko | grep depends    # polecenie dostosuj pod siebie

4 Odpowiedź przez mar_w

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

LEDE nie ma kernela 3.18 oraz moduł e4000 występuje przeważnie przy RTL2830/32 niekiedy jest fc0013 a nie przy IT9135 smile

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

5 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Wykonałem

# opkg update
# opkg install kmod-i2c-core kmod-input-core kmod-regmap

niby władowalo, ale dalej THE nie widzi



dmeseg
BusyBox v1.25.1 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
/________/  LE  \  |____|___|___/|___|                      lede-project.org
\        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (17.01-SNAPSHOT, r3825-28483d4)
    \________\/    -----------------------------------------------------------

-----------------------------------------------------------------------------
|                                                                           |
| Build time: 2018-02-10 07:51 CET                                          |
|                                                                           |
| Cezary Jackiewicz (obsy), http://eko.one.pl                               |
|                                                                           |
-----------------------------------------------------------------------------
| Machine: TP-Link TL-WR1043N/ND v1                                         |
| Uptime: 0d, 00:05:44                                                      |
| Load: 0.19 0.34 0.20                                                      |
| Flash: total: 1.3GB, free: 1.2GB, used: 1%                                |
| Memory: total: 27.1MB, free: 8.1MB, used: 70%                             |
| WAN: 89.239.76.132, proto: dhcp                                           |
| LAN: 192.168.0.1, leases: 1                                               |
| radio0: mode: ap, ssid: Gargoyle, channel: 7, conn: 1                     |
-----------------------------------------------------------------------------
root@LEDE:~# dmesg
[    0.000000] Linux version 4.4.112 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3785-ceea0ac) ) #0 Fri Jan 26 07:37:28 2018
[    0.000000] MyLoader: sysp=2aa2aaa2, boardp=aa22a2aa, parts=a2aaaa8a
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9132 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] No valid device tree found, continuing without
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 804384d0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: board=TL-WR1043ND  console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 27480K/32768K available (3122K kernel code, 162K rwdata, 780K rodata, 280K init, 205K bss, 5288K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.007887] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.090589] pid_max: default: 32768 minimum: 301
[    0.095367] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.101974] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.112352] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.122207] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.129918] NET: Registered protocol family 16
[    0.136255] MIPS: machine is TP-LINK TL-WR1043ND
[    0.419666] clocksource: Switched to clocksource MIPS
[    0.426489] NET: Registered protocol family 2
[    0.432104] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.439076] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.445499] TCP: Hash tables configured (established 1024 bind 1024)
[    0.451993] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.457836] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.464484] NET: Registered protocol family 1
[    0.468924] PCI: CLS 0 bytes, default 32
[    0.474192] Crashlog allocated RAM at address 0x1f00000
[    0.498402] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.504300] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.517301] io scheduler noop registered
[    0.521288] io scheduler deadline registered (default)
[    0.526742] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.537019] console [ttyS0] disabled
[    0.560634] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[    0.569328] console [ttyS0] enabled
[    0.576352] bootconsole [early0] disabled
[    0.590472] m25p80 spi0.0: found en25q64, expected m25p80
[    0.595926] m25p80 spi0.0: en25q64 (8192 Kbytes)
[    0.601882] 5 tp-link partitions found on MTD device spi0.0
[    0.607495] Creating 5 MTD partitions on "spi0.0":
[    0.612367] 0x000000000000-0x000000020000 : "u-boot"
[    0.619154] 0x000000020000-0x0000001702ac : "kernel"
[    0.626233] 0x0000001702ac-0x0000007f0000 : "rootfs"
[    0.633290] mtd: device 2 (rootfs) set to be root filesystem
[    0.639024] 1 squashfs-split partitions found on MTD device rootfs
[    0.645312] 0x000000610000-0x0000007f0000 : "rootfs_data"
[    0.652804] 0x0000007f0000-0x000000800000 : "art"
[    0.659585] 0x000000020000-0x0000007f0000 : "firmware"
[    0.668595] Realtek RTL8366RB ethernet switch driver version 0.2.4
[    0.779688] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[    0.786408] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.997091] libphy: rtl8366rb: probed
[    1.321735] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    1.330884] NET: Registered protocol family 10
[    1.339980] NET: Registered protocol family 17
[    1.344554] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.357429] 8021q: 802.1Q VLAN Support v1.8
[    1.363803] hctosys: unable to open rtc device (rtc0)
[    1.374994] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.383875] Freeing unused kernel memory: 280K
[    2.779844] init: Console is alive
[    2.783523] init: - watchdog -
[    4.804023] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.988429] usbcore: registered new interface driver usbfs
[    4.994138] usbcore: registered new interface driver hub
[    4.999614] usbcore: registered new device driver usb
[    5.049900] SCSI subsystem initialized
[    5.061322] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.069959] ehci-platform: EHCI generic platform driver
[    5.075320] ehci-platform ehci-platform: EHCI Host Controller
[    5.081186] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.089287] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.109710] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.117233] hub 1-0:1.0: USB hub found
[    5.121442] hub 1-0:1.0: 1 port detected
[    5.131076] usbcore: registered new interface driver usb-storage
[    5.137968] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.147805] init: - preinit -
[    5.597330] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    5.998739] hub 1-1:1.0: USB hub found
[    6.019314] hub 1-1:1.0: 4 ports detected
[    6.125723] ar71xx: pll_reg 0xb8050014: 0x1a000000
[    6.125761] eth0: link up (1000Mbps/Full duplex)
[    6.204971] random: procd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[    6.319690] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[    6.529698] usb 1-1.3: new high-speed USB device number 4 using ehci-platform
[    6.663315] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[    6.670621] scsi host0: usb-storage 1-1.3:1.0
[    6.749700] usb 1-1.4: new high-speed USB device number 5 using ehci-platform
[    6.881674] hub 1-1.4:1.0: USB hub found
[    6.885945] hub 1-1.4:1.0: 4 ports detected
[    7.169701] usb 1-1.4.1: new high-speed USB device number 6 using ehci-platform
[    7.302974] usb-storage 1-1.4.1:1.0: USB Mass Storage device detected[    7.310413] scsi host1: usb-storage 1-1.4.1:1.0
[    7.409695] usb 1-1.4.2: new high-speed USB device number 7 using ehci-platform
[    7.542347] usb-storage 1-1.4.2:1.0: USB Mass Storage device detected[    7.549772] scsi host2: usb-storage 1-1.4.2:1.0
[    7.629692] usb 1-1.4.4: new high-speed USB device number 8 using ehci-platform
[    7.709203] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[    7.720658] sd 0:0:0:0: [sda] 3905407 512-byte logical blocks: (2.00 GB/1.86 GiB)
[    7.728746] sd 0:0:0:0: [sda] Write Protect is off
[    7.733660] sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08
[    7.734231] sd 0:0:0:0: [sda] No Caching mode page found
[    7.739613] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    7.757879]  sda: sda1 sda2
[    7.765815] usb-storage 1-1.4.4:1.0: USB Mass Storage device detected[    7.773817] scsi host3: usb-storage 1-1.4.4:1.0
[    7.780220] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    8.380626] scsi 1:0:0:0: Direct-Access     General  USB Flash Disk   1100 PQ: 0 ANSI: 4
[    8.392028] sd 1:0:0:0: [sdb] 31494144 512-byte logical blocks: (16.1 GB/15.0 GiB)
[    8.403392] mount_root: loading kmods from internal overlay
[    8.409549] sd 1:0:0:0: [sdb] Write Protect is off
[    8.414473] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    8.419734] sd 1:0:0:0: [sdb] No Caching mode page found
[    8.425194] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[    8.454136]  sdb: sdb1
[    8.471639] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[    8.488232] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    8.497495] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    8.612244] scsi 2:0:0:0: Direct-Access     WD       Elements 10A2    1033 PQ: 0 ANSI: 6
[    8.623404] sd 2:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/466 GiB)
[    8.633433] sd 2:0:0:0: [sdc] Write Protect is off
[    8.638321] sd 2:0:0:0: [sdc] Mode Sense: 53 00 10 08
[    8.661436] sd 2:0:0:0: [sdc] No Caching mode page found
[    8.666908] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[    8.777085] scsi 3:0:0:0: Direct-Access     SanDisk  Ultra            1.00 PQ: 0 ANSI: 6
[    8.789175] sd 3:0:0:0: [sdd] 60751872 512-byte logical blocks: (31.1 GB/29.0 GiB)
[    8.798558] sd 3:0:0:0: [sdd] Write Protect is off
[    8.803503] sd 3:0:0:0: [sdd] Mode Sense: 43 00 00 00
[    8.804877] sd 3:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    8.821816]  sdd: sdd1
[    8.830009] sd 3:0:0:0: [sdd] Attached SCSI removable disk
[    8.895825] jffs2: notice: (464) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.911961] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   10.443177]  sdc: sdc1 sdc2 sdc3
[   10.451607] sd 2:0:0:0: [sdc] Attached SCSI disk
[   11.754577] EXT4-fs (sda1): recovery complete
[   11.922254] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[   11.951272] mount_root: switched to extroot
[   11.959163] urandom-seed: Seeding with /etc/urandom.seed
[   12.128803] eth0: link down
[   12.146091] procd: - early -
[   12.149117] procd: - watchdog -
[   12.531994] random: nonblocking pool is initialized
[   13.046636] procd: - watchdog -
[   13.050184] procd: - ubus -
[   13.525735] procd: - init -
[   15.242056] kmodloader: loading kernel modules from /etc/modules.d/*
[   15.342559] tun: Universal TUN/TAP device driver, 1.6
[   15.347652] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.405332] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.483236] i2c /dev entries driver
[   15.516502] fuse init (API version 7.23)
[   15.560124] usbcore: registered new interface driver cdc_acm
[   15.565826] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   15.641749] usbcore: registered new interface driver cdc_wdm
[   15.652612] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   15.660738] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   15.713289] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.750926] nf_conntrack version 0.5.0 (433 buckets, 1732 max)
[   15.965606] usbcore: registered new interface driver usblp
[   16.032574] usbcore: registered new interface driver usbserial
[   16.038572] usbcore: registered new interface driver usbserial_generic
[   16.045349] usbserial: USB Serial support registered for generic
[   16.177884] xt_time: kernel timezone is -0000
[   16.202379] usbcore: registered new interface driver cdc_ether
[   16.233609] usbcore: registered new interface driver cdc_ncm
[   16.340062] usbcore: registered new interface driver huawei_cdc_ncm
[   16.604044] PPP generic driver version 2.4.2
[   16.631405] NET: Registered protocol family 24
[   16.662881] usbcore: registered new interface driver qmi_wwan
[   16.693042] usbcore: registered new interface driver rndis_host
[   16.722705] usbcore: registered new interface driver sierra
[   16.728450] usbserial: USB Serial support registered for Sierra USB modem
[   16.759504] usbcore: registered new interface driver sierra_net
[   16.902634] usbcore: registered new interface driver cdc_mbim
[   16.952313] usbcore: registered new interface driver option
[   16.958059] usbserial: USB Serial support registered for GSM modem (1-port)
[   17.021697] usbcore: registered new interface driver qcserial
[   17.027625] usbserial: USB Serial support registered for Qualcomm USB modem
[   17.172597] ath: EEPROM regdomain: 0x0
[   17.172624] ath: EEPROM indicates default country code should be used[   17.172638] ath: doing EEPROM country->regdmn map search
[   17.172663] ath: country maps to regdmn code: 0x3a
[   17.172679] ath: Country alpha2 being used: US
[   17.172693] ath: Regpair used: 0x3a
[   17.214363] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   17.221277] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[   17.449518] kmodloader: done loading kernel modules from /etc/modules.d/*
[   23.161244] Adding 486396k swap on /dev/sda2.  Priority:-1 extents:1 across:486396k
[   23.709557] EXT4-fs (sdb1): warning: maximal mount count reached, running e2fsck is recommended
[   23.723951] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts:
[   23.899837] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[   23.925497] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   24.430253] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts:
[   32.395789] ar71xx: pll_reg 0xb8050014: 0x1a000000
[   32.397103] eth0: link up (1000Mbps/Full duplex)
[   32.409554] device eth0.1 entered promiscuous mode
[   32.414478] device eth0 entered promiscuous mode
[   32.441134] br-lan: port 1(eth0.1) entered forwarding state
[   32.446793] br-lan: port 1(eth0.1) entered forwarding state
[   34.280418] ath: EEPROM regdomain: 0x8268
[   34.280448] ath: EEPROM indicates we should expect a country code
[   34.280468] ath: doing EEPROM country->regdmn map search
[   34.280486] ath: country maps to regdmn code: 0x37
[   34.280503] ath: Country alpha2 being used: PL
[   34.280516] ath: Regpair used: 0x37
[   34.280535] ath: regdomain 0x8268 dynamically updated by user
[   34.439693] br-lan: port 1(eth0.1) entered forwarding state
[   39.626204] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   39.887357] device wlan0 entered promiscuous mode
[   41.940185] usb 1-1.1: dvb_usb_af9035: prechip_version=83 chip_version=01 chip_type=9135
[   41.959817] usb 1-1.1: dvb_usb_v2: found a 'ITE 9135 Generic' in warm state
[   41.980743] usb 1-1.1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
[   41.991893] DVB: registering new adapter (ITE 9135 Generic)
[   42.125410] usbcore: registered new interface driver dvb_usb_af9035
[   42.673629] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   42.680301] br-lan: port 2(wlan0) entered forwarding state
[   42.685884] br-lan: port 2(wlan0) entered forwarding state
[   44.679713] br-lan: port 2(wlan0) entered forwarding state
[   95.425927] TCP: request_sock_TCP: Possible SYN flooding on port 9981. Sending cookies.  Check SNMP counters.
root@LEDE:~# dmesg
[    0.000000] Linux version 4.4.112 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3785-ceea0ac) ) #0 Fri Jan 26 07:37:28 2018
[    0.000000] MyLoader: sysp=2aa2aaa2, boardp=aa22a2aa, parts=a2aaaa8a
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9132 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] No valid device tree found, continuing without
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 804384d0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: board=TL-WR1043ND  console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 27480K/32768K available (3122K kernel code, 162K rwdata, 780K rodata, 280K init, 205K bss, 5288K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000012] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.007887] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.090589] pid_max: default: 32768 minimum: 301
[    0.095367] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.101974] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.112352] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.122207] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.129918] NET: Registered protocol family 16
[    0.136255] MIPS: machine is TP-LINK TL-WR1043ND
[    0.419666] clocksource: Switched to clocksource MIPS
[    0.426489] NET: Registered protocol family 2
[    0.432104] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.439076] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.445499] TCP: Hash tables configured (established 1024 bind 1024)
[    0.451993] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.457836] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.464484] NET: Registered protocol family 1
[    0.468924] PCI: CLS 0 bytes, default 32
[    0.474192] Crashlog allocated RAM at address 0x1f00000
[    0.498402] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.504300] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.517301] io scheduler noop registered
[    0.521288] io scheduler deadline registered (default)
[    0.526742] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.537019] console [ttyS0] disabled
[    0.560634] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[    0.569328] console [ttyS0] enabled
[    0.576352] bootconsole [early0] disabled
[    0.590472] m25p80 spi0.0: found en25q64, expected m25p80
[    0.595926] m25p80 spi0.0: en25q64 (8192 Kbytes)
[    0.601882] 5 tp-link partitions found on MTD device spi0.0
[    0.607495] Creating 5 MTD partitions on "spi0.0":
[    0.612367] 0x000000000000-0x000000020000 : "u-boot"
[    0.619154] 0x000000020000-0x0000001702ac : "kernel"
[    0.626233] 0x0000001702ac-0x0000007f0000 : "rootfs"
[    0.633290] mtd: device 2 (rootfs) set to be root filesystem
[    0.639024] 1 squashfs-split partitions found on MTD device rootfs
[    0.645312] 0x000000610000-0x0000007f0000 : "rootfs_data"
[    0.652804] 0x0000007f0000-0x000000800000 : "art"
[    0.659585] 0x000000020000-0x0000007f0000 : "firmware"
[    0.668595] Realtek RTL8366RB ethernet switch driver version 0.2.4
[    0.779688] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[    0.786408] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.997091] libphy: rtl8366rb: probed
[    1.321735] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    1.330884] NET: Registered protocol family 10
[    1.339980] NET: Registered protocol family 17
[    1.344554] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.357429] 8021q: 802.1Q VLAN Support v1.8
[    1.363803] hctosys: unable to open rtc device (rtc0)
[    1.374994] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.383875] Freeing unused kernel memory: 280K
[    2.779844] init: Console is alive
[    2.783523] init: - watchdog -
[    4.804023] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.988429] usbcore: registered new interface driver usbfs
[    4.994138] usbcore: registered new interface driver hub
[    4.999614] usbcore: registered new device driver usb
[    5.049900] SCSI subsystem initialized
[    5.061322] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.069959] ehci-platform: EHCI generic platform driver
[    5.075320] ehci-platform ehci-platform: EHCI Host Controller
[    5.081186] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.089287] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.109710] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.117233] hub 1-0:1.0: USB hub found
[    5.121442] hub 1-0:1.0: 1 port detected
[    5.131076] usbcore: registered new interface driver usb-storage
[    5.137968] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.147805] init: - preinit -
[    5.597330] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    5.998739] hub 1-1:1.0: USB hub found
[    6.019314] hub 1-1:1.0: 4 ports detected
[    6.125723] ar71xx: pll_reg 0xb8050014: 0x1a000000
[    6.125761] eth0: link up (1000Mbps/Full duplex)
[    6.204971] random: procd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[    6.319690] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[    6.529698] usb 1-1.3: new high-speed USB device number 4 using ehci-platform
[    6.663315] usb-storage 1-1.3:1.0: USB Mass Storage device detected
[    6.670621] scsi host0: usb-storage 1-1.3:1.0
[    6.749700] usb 1-1.4: new high-speed USB device number 5 using ehci-platform
[    6.881674] hub 1-1.4:1.0: USB hub found
[    6.885945] hub 1-1.4:1.0: 4 ports detected
[    7.169701] usb 1-1.4.1: new high-speed USB device number 6 using ehci-platform
[    7.302974] usb-storage 1-1.4.1:1.0: USB Mass Storage device detected[    7.310413] scsi host1: usb-storage 1-1.4.1:1.0
[    7.409695] usb 1-1.4.2: new high-speed USB device number 7 using ehci-platform
[    7.542347] usb-storage 1-1.4.2:1.0: USB Mass Storage device detected[    7.549772] scsi host2: usb-storage 1-1.4.2:1.0
[    7.629692] usb 1-1.4.4: new high-speed USB device number 8 using ehci-platform
[    7.709203] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[    7.720658] sd 0:0:0:0: [sda] 3905407 512-byte logical blocks: (2.00 GB/1.86 GiB)
[    7.728746] sd 0:0:0:0: [sda] Write Protect is off
[    7.733660] sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08
[    7.734231] sd 0:0:0:0: [sda] No Caching mode page found
[    7.739613] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    7.757879]  sda: sda1 sda2
[    7.765815] usb-storage 1-1.4.4:1.0: USB Mass Storage device detected[    7.773817] scsi host3: usb-storage 1-1.4.4:1.0
[    7.780220] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    8.380626] scsi 1:0:0:0: Direct-Access     General  USB Flash Disk   1100 PQ: 0 ANSI: 4
[    8.392028] sd 1:0:0:0: [sdb] 31494144 512-byte logical blocks: (16.1 GB/15.0 GiB)
[    8.403392] mount_root: loading kmods from internal overlay
[    8.409549] sd 1:0:0:0: [sdb] Write Protect is off
[    8.414473] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    8.419734] sd 1:0:0:0: [sdb] No Caching mode page found
[    8.425194] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[    8.454136]  sdb: sdb1
[    8.471639] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[    8.488232] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    8.497495] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    8.612244] scsi 2:0:0:0: Direct-Access     WD       Elements 10A2    1033 PQ: 0 ANSI: 6
[    8.623404] sd 2:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/466 GiB)
[    8.633433] sd 2:0:0:0: [sdc] Write Protect is off
[    8.638321] sd 2:0:0:0: [sdc] Mode Sense: 53 00 10 08
[    8.661436] sd 2:0:0:0: [sdc] No Caching mode page found
[    8.666908] sd 2:0:0:0: [sdc] Assuming drive cache: write through
[    8.777085] scsi 3:0:0:0: Direct-Access     SanDisk  Ultra            1.00 PQ: 0 ANSI: 6
[    8.789175] sd 3:0:0:0: [sdd] 60751872 512-byte logical blocks: (31.1 GB/29.0 GiB)
[    8.798558] sd 3:0:0:0: [sdd] Write Protect is off
[    8.803503] sd 3:0:0:0: [sdd] Mode Sense: 43 00 00 00
[    8.804877] sd 3:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    8.821816]  sdd: sdd1
[    8.830009] sd 3:0:0:0: [sdd] Attached SCSI removable disk
[    8.895825] jffs2: notice: (464) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.911961] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   10.443177]  sdc: sdc1 sdc2 sdc3
[   10.451607] sd 2:0:0:0: [sdc] Attached SCSI disk
[   11.754577] EXT4-fs (sda1): recovery complete
[   11.922254] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[   11.951272] mount_root: switched to extroot
[   11.959163] urandom-seed: Seeding with /etc/urandom.seed
[   12.128803] eth0: link down
[   12.146091] procd: - early -
[   12.149117] procd: - watchdog -
[   12.531994] random: nonblocking pool is initialized
[   13.046636] procd: - watchdog -
[   13.050184] procd: - ubus -
[   13.525735] procd: - init -
[   15.242056] kmodloader: loading kernel modules from /etc/modules.d/*
[   15.342559] tun: Universal TUN/TAP device driver, 1.6
[   15.347652] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.405332] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.483236] i2c /dev entries driver
[   15.516502] fuse init (API version 7.23)
[   15.560124] usbcore: registered new interface driver cdc_acm
[   15.565826] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   15.641749] usbcore: registered new interface driver cdc_wdm
[   15.652612] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   15.660738] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   15.713289] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.750926] nf_conntrack version 0.5.0 (433 buckets, 1732 max)
[   15.965606] usbcore: registered new interface driver usblp
[   16.032574] usbcore: registered new interface driver usbserial
[   16.038572] usbcore: registered new interface driver usbserial_generic
[   16.045349] usbserial: USB Serial support registered for generic
[   16.177884] xt_time: kernel timezone is -0000
[   16.202379] usbcore: registered new interface driver cdc_ether
[   16.233609] usbcore: registered new interface driver cdc_ncm
[   16.340062] usbcore: registered new interface driver huawei_cdc_ncm
[   16.604044] PPP generic driver version 2.4.2
[   16.631405] NET: Registered protocol family 24
[   16.662881] usbcore: registered new interface driver qmi_wwan
[   16.693042] usbcore: registered new interface driver rndis_host
[   16.722705] usbcore: registered new interface driver sierra
[   16.728450] usbserial: USB Serial support registered for Sierra USB modem
[   16.759504] usbcore: registered new interface driver sierra_net
[   16.902634] usbcore: registered new interface driver cdc_mbim
[   16.952313] usbcore: registered new interface driver option
[   16.958059] usbserial: USB Serial support registered for GSM modem (1-port)
[   17.021697] usbcore: registered new interface driver qcserial
[   17.027625] usbserial: USB Serial support registered for Qualcomm USB modem
[   17.172597] ath: EEPROM regdomain: 0x0
[   17.172624] ath: EEPROM indicates default country code should be used[   17.172638] ath: doing EEPROM country->regdmn map search
[   17.172663] ath: country maps to regdmn code: 0x3a
[   17.172679] ath: Country alpha2 being used: US
[   17.172693] ath: Regpair used: 0x3a
[   17.214363] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   17.221277] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[   17.449518] kmodloader: done loading kernel modules from /etc/modules.d/*
[   23.161244] Adding 486396k swap on /dev/sda2.  Priority:-1 extents:1 across:486396k
[   23.709557] EXT4-fs (sdb1): warning: maximal mount count reached, running e2fsck is recommended
[   23.723951] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts:
[   23.899837] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[   23.925497] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   24.430253] EXT4-fs (sdd1): mounted filesystem with ordered data mode. Opts:
[   32.395789] ar71xx: pll_reg 0xb8050014: 0x1a000000
[   32.397103] eth0: link up (1000Mbps/Full duplex)
[   32.409554] device eth0.1 entered promiscuous mode
[   32.414478] device eth0 entered promiscuous mode
[   32.441134] br-lan: port 1(eth0.1) entered forwarding state
[   32.446793] br-lan: port 1(eth0.1) entered forwarding state
[   34.280418] ath: EEPROM regdomain: 0x8268
[   34.280448] ath: EEPROM indicates we should expect a country code
[   34.280468] ath: doing EEPROM country->regdmn map search
[   34.280486] ath: country maps to regdmn code: 0x37
[   34.280503] ath: Country alpha2 being used: PL
[   34.280516] ath: Regpair used: 0x37
[   34.280535] ath: regdomain 0x8268 dynamically updated by user
[   34.439693] br-lan: port 1(eth0.1) entered forwarding state
[   39.626204] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   39.887357] device wlan0 entered promiscuous mode
[   41.940185] usb 1-1.1: dvb_usb_af9035: prechip_version=83 chip_version=01 chip_type=9135
[   41.959817] usb 1-1.1: dvb_usb_v2: found a 'ITE 9135 Generic' in warm state
[   41.980743] usb 1-1.1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
[   41.991893] DVB: registering new adapter (ITE 9135 Generic)
[   42.125410] usbcore: registered new interface driver dvb_usb_af9035
[   42.673629] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   42.680301] br-lan: port 2(wlan0) entered forwarding state
[   42.685884] br-lan: port 2(wlan0) entered forwarding state
[   44.679713] br-lan: port 2(wlan0) entered forwarding state
[   95.425927] TCP: request_sock_TCP: Possible SYN flooding on port 9981. Sending cookies.  Check SNMP counters.
root@LEDE:~# /etc/init.d/tvheadend restart
root@LEDE:~#

6 Odpowiedź przez mar_w (edytowany przez mar_w 2018-03-11 22:48:01)

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

firmware masz w katalogu /lib/firmware ?
zatrzymaj TVH bo on robi dziwne rzeczy, o których na razie nie wspomnę.

/etc/init.d/tvheadend stop
/etc/init.d/tvheadend disable

wypnij i wepnij z powrotem ten stick i pokaż logread - końcówkę

logread | tail -n 25
Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

7 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

tak

root@LEDE:/lib/firmware# ls
dvb-usb-it9135-01.fw  dvb-usb-it9135-02.fw
root@LEDE:/lib/firmware#

8 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

oot@LEDE:/etc# logread | tail -n 25
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb: queued to save (size 191)
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb:   brands     0
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb:   seasons    0
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb:   episodes   0
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb:   broadcasts 0
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: mpegts: 177.5MHz in naziemna (0xcad640) - deleting
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb: save start
Sun Mar 11 22:54:04 2018 daemon.info tvheadend[2156]: epgdb: stored (size 191)
Sun Mar 11 22:54:05 2018 daemon.notice tvheadend[2156]: STOP: Exiting HTS Tvheadend
Sun Mar 11 22:57:48 2018 daemon.info dnsmasq-dhcp[1769]: DHCPREQUEST(br-lan) 192.168.0.201 00:1e:33:5b:fa:09
Sun Mar 11 22:57:48 2018 daemon.info dnsmasq-dhcp[1769]: DHCPACK(br-lan) 192.168.0.201 00:1e:33:5b:fa:09 Toshibka
Sun Mar 11 22:58:14 2018 kern.info kernel: [ 2218.218185] usb 1-1.1: USB disconnect, device number 3
Sun Mar 11 22:58:14 2018 kern.info kernel: [ 2218.839187] usb 1-1.1: new full-speed USB device number 9 using ehci-platform
Sun Mar 11 22:58:14 2018 kern.err kernel: [ 2219.018173] usb 1-1.1: device descriptor read/64, error -32
Sun Mar 11 22:58:15 2018 kern.err kernel: [ 2219.519998] usb 1-1.1: device descriptor read/64, error -32
Sun Mar 11 22:58:15 2018 kern.info kernel: [ 2219.859219] usb 1-1.1: new full-speed USB device number 10 using ehci-platform
Sun Mar 11 22:58:15 2018 kern.err kernel: [ 2220.010385] usb 1-1.1: device descriptor read/64, error -32
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.209119] usb 1-1.1: new high-speed USB device number 11 using ehci-platform
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.345836] usb 1-1.1: dvb_usb_af9035: prechip_version=83 chip_version=01 chip_type=9135
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.369329] usb 1-1.1: dvb_usb_v2: found a 'ITE 9135 Generic' in cold state
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.385388] usb 1-1.1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9135-01.fw'
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.564199] usb 1-1.1: dvb_usb_af9035: firmware version=12.54.14.0
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.570579] usb 1-1.1: dvb_usb_v2: found a 'ITE 9135 Generic' in warm state
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.630085] usb 1-1.1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
Sun Mar 11 22:58:25 2018 kern.info kernel: [ 2229.641235] DVB: registering new adapter (ITE 9135 Generic)
root@LEDE:/etc#

9 Odpowiedź przez mar_w (edytowany przez mar_w 2018-03-11 23:11:17)

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

usb 1-1.1: device descriptor read/64, error -32

czyżby hub USB?? też tak miałem... zmieniłem Huba na innego...
lub coś złego jest z magistralą...

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

10 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Spróbuję podpiąć w inny port

mar_w napisał/a:

usb 1-1.1: device descriptor read/64, error -32

czyżby hub USB?? też tak miałem...
lub coś złego jest z magistralą...

11 Odpowiedź przez mar_w (edytowany przez mar_w 2018-03-11 23:27:04)

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Inny port w Hubie może nie poprawić sytuacji. Zmień Hub. Lub podepnij bezpośrednio do USB routera.

OT: ogólnie to szacunek, że najpierw czytałeś FAQ i poradniki a potem forum i w zasadzie hardware Cię pokonał a nie metoda instalacji, która była prawie kompletna, a to już duży plus dla Ciebie smile

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

12 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

wypiąłem dysk

I zmieniłem port w gubię

oot@LEDE:~# logread | tail -n 25
Sun Mar 11 23:23:40 2018 daemon.info dnsmasq[1673]: read /etc/hosts - 4 addresses
Sun Mar 11 23:23:40 2018 daemon.info dnsmasq[1673]: read /tmp/hosts/odhcpd - 0 addresses
Sun Mar 11 23:23:40 2018 daemon.info dnsmasq[1673]: read /tmp/hosts/dhcp.cfg02411c - 2 addresses
Sun Mar 11 23:23:40 2018 daemon.info dnsmasq-dhcp[1673]: read /etc/ethers - 0 addresses
Sun Mar 11 23:23:52 2018 authpriv.info dropbear[1984]: Child connection from 192.168.0.224:50667
Sun Mar 11 23:23:57 2018 authpriv.notice dropbear[1984]: Password auth succeeded for 'root' from 192.168.0.224:50667
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb: snapshot start
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb: queued to save (size 191)
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb:   brands     0
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb:   seasons    0
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb:   episodes   0
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb:   broadcasts 0
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: mpegts: 177.5MHz in naziemna (0xc72550) - deleting
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb: save start
Sun Mar 11 23:24:04 2018 daemon.info tvheadend[1775]: epgdb: stored (size 191)
Sun Mar 11 23:24:04 2018 daemon.notice tvheadend[1775]: STOP: Exiting HTS Tvheadend
Sun Mar 11 23:24:27 2018 kern.info kernel: [  132.330127] usb 1-1.4.3: USB disconnect, device number 6
Sun Mar 11 23:24:31 2018 kern.info kernel: [  136.659752] usb 1-1.4.3: new high-speed USB device number 8 using ehci-platform
Sun Mar 11 23:24:31 2018 kern.info kernel: [  136.796530] usb 1-1.4.3: dvb_usb_af9035: prechip_version=83 chip_version=01 chip_type=9135
Sun Mar 11 23:24:32 2018 kern.info kernel: [  136.819897] usb 1-1.4.3: dvb_usb_v2: found a 'ITE 9135 Generic' in cold state
Sun Mar 11 23:24:32 2018 kern.info kernel: [  136.835394] usb 1-1.4.3: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9135-01.fw'
Sun Mar 11 23:24:32 2018 kern.info kernel: [  137.113634] usb 1-1.4.3: dvb_usb_af9035: firmware version=12.54.14.0
Sun Mar 11 23:24:32 2018 kern.info kernel: [  137.120163] usb 1-1.4.3: dvb_usb_v2: found a 'ITE 9135 Generic' in warm state
Sun Mar 11 23:24:32 2018 kern.info kernel: [  137.180911] usb 1-1.4.3: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
Sun Mar 11 23:24:32 2018 kern.info kernel: [  137.192232] DVB: registering new adapter (ITE 9135 Generic)
root@LEDE:~#

13 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

podpiąć za bardzo nie mogę, bo mam overlays'a na pendraku.
Innego huba na razie nie mam.
Wiem, że na gargolcu mi to kiedyś chodziło. spróbowałem na leżę, ale właśnie coś TH nie widzi




mar_w napisał/a:

Inny port w Hubie może nie poprawić sytuacji. Zmień Hub. Lub podepnij bezpośrednio do USB routera.

OT: ogólnie to szacunek, że najpierw czytałeś FAQ i poradniki a potem forum i w zasadzie hardware Cię pokonał a nie metoda instalacji, która była prawie kompletna, a to już duży plus dla Ciebie smile

14 Odpowiedź przez mar_w (edytowany przez mar_w 2018-03-12 00:31:54)

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

wg posta #1 to brakuje ci modułu:

insmod dvb-usb

sprawdź zależności żebyś go nie wstawił za wcześnie (przykład od @ad2014 - zamiast e4000 wstaw dvb-usb.ko)

strings /lib/modules/4.4.112/dvb-usb.ko | grep depends

za rc-core i dvb-core może być ten dvb-usb

EDIT2: ten dvb-usb jest to starszych wersji więc chyba można go pominąć. powinien wystarczyć dvb_usb_v2. Ja akurat mam ale pewnie z innego powodu smile

EDIT: brakuje Ci jeszcze af9033.ko
może być pomiędzy it913x a rc-it913x-v1

a potem w logach powinieneś mieć magiczne:

... DVB: registering new adapter (ITE 9135 Generic)...
...successfully initialized and connected

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

15 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Dzięki za pomoc trochę wymęczyłem.
Okazało się, że między innymi w jednym miejscu stuknąłem apostrof.
Przeszukałem wszelkie zależności i teraz chodzi. Piękne dzięki.

Dla potomnych takie moduły

insmod input-core
insmod rc-core
insmod usbcore
insmod dvb-core
insmod dvb-usb
insmod it913x
insmod af9033
insmod dvb_usb_v2
insmod rc-it913x-v1
insmod rc-it913x-v2
insmod dvb-usb-af9035

16 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Może jeszcze podpowiedź który system wybrać hspr amatorska czy pass.
chciałbym aby jak najmniej obiążał procesor routera.
Matroska jest jak gdyby pochodną pass.
Więc się zastanawiam, czy nie więcej obciąża.

17 Odpowiedź przez mar_w

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

na 1043v1 już samo włączenie epg zamula go dobrze. Spójrz na współczynnik obciążenia procka za pomocą aplikacji np. top i to bez streamingu kanałów HD...
Trzeba kołować mocniejszy sprzęt na takie zabawy, żeby być zadowolonym.

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

18 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

mar_w napisał/a:

na 1043v1 już samo włączenie epg zamula go dobrze. Spójrz na współczynnik obciążenia procka za pomocą aplikacji np. top i to bez streamingu kanałów HD...
Trzeba kołować mocniejszy sprzęt na takie zabawy, żeby być zadowolonym.

Tak obciążenie - to widać. Wczoraj uruchomiłem równolegle na laptopie (VLC) oraz na komórce Samsung j5 2016 - działało.

W momencie gdy jest streaming to nawet nie mogłem wejść przez WWW na router.

Co to za aplikacja top? Rzuciłem hasło na wujka google, ale miliony odpowiedzi, a o aplikacji nic.

Wyłączyłem na TVH epg, zawsze to chyba mniej. Zastanawiam się czy można na TVH wyłączyć kanał teletekstu i czy można wyłączyć drugi strumień dźwięku. W tych wszystkich opcjach nic nie zauważyłem.

Co do mocniejszego sprzętu obserwuję teraz aukcje WDR-4300, ale nie wiem jak się on do tego by spisał.

Zresztą to co robię to bardziej dla zabawy, czy mi się uda...

19 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,346

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Zaloguj się przez ssh do router i wpisz top.  Aż dziwne że tego nigdy nie używałeś.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

20 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Cezary napisał/a:

Zaloguj się przez ssh do router i wpisz top.  Aż dziwne że tego nigdy nie używałeś.

Może dlatego, że w czasie stramingu wląsnie ciezko było się logować

Dzięki

21 Odpowiedź przez Tygrys20

  • Zarejestrowany: 2018-03-11
  • Posty: 14

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Tak dla ciekawości przy jednoczesnym laptopie oglądanie

  PID  PPID USER     STAT   VSZ %VSZ %CPU COMMAND                        1845     1 root     S    14612  53%  16% /usr/bin/tvheadend -B -c /etc/tvheade                                                                  2543  2459 root     R     1204   4%   0% top                               3     2 root     SW       0   0%   0% [ksoftirqd/0]                  2458  1192 root     S     1124   4%   0% /usr/sbin/dropbear -F -P /var/run/dro                                                                  2246     2 root     SW       0   0%   0% [kworker/0:1]                  1224     1 root     S     3596  13%   0% /usr/sbin/uhttpd -f -h /www -r LEDE -                                                                  1497     1 root     S     2468   9%   0% /usr/sbin/nmbd -F              1496     1 root     S     2416   9%   0% /usr/sbin/smbd -F              1529     1 nobody   S     1832   7%   0% avahi-daemon: running [LEDE.local]                                                                     1100     1 root     S     1704   6%   0% /sbin/netifd                   1673     1 root     S     1684   6%   0% /usr/sbin/hostapd -s -P /var/run/wifi                                                                     1     0 root     S     1532   6%   0% /sbin/procd                    1307     1 root     S     1460   5%   0% /usr/sbin/dbus-daemon --system  995     1 root     S     1440   5%   0% /sbin/rpcd                     1145     1 root     S     1416   5%   0% /usr/sbin/odhcpd                978     1 root     S     1224   4%   0% /sbin/logd -S 64               2459  2458 root     S     1196   4%   0% -ash                           1996     1 root     S <   1188   4%   0% /usr/sbin/ntpd -n -N -S /usr/sbin/ntp                                                                  1324  1100 root     S     1188   4%   0% udhcpc -p /var/run/udhcpc-eth0.2.pid                                                                    556     1 root     S     1176   4%   0% /sbin/ubusd

22 Odpowiedź przez steel_rat (edytowany przez steel_rat 2018-03-13 16:55:13)

  • Zarejestrowany: 2017-04-30
  • Posty: 569

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

Ja tam postawiłem tvheadend na Raspberry pi2.  Działa ok. Nie wiem czy jest sens męczyć router.

23 Odpowiedź przez mar_w

  • mar_w
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2014-08-16
  • Posty: 2,127

Odp: TVHEADEND Luci Lede 17.01-SNAPSHOT, r3825-28483d4 nie widzi tunera

@Tygrys20 i inni
zrzuty z konsoli najlepiej brać w BBCode - sekcja code lub quote bo lepiej widać smile
Chodziło mi raczej o Load average: który bez streamingu wychodzi powyżej 1.0 gdzie top dla tej aplikacji pokazuje około 16% przy wyłączonej reszcie innych "niepotrzebnych" serwerów i apek.
możesz też użyć mniejszy interwał czasowy, żeby zobaczyć piki:

 top -d 1
Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *