Cezary, ratuj!
Wgrałam do Easybox 802 soft przeznaczony do 803A, przez przypadek, w CC da się to zrobić przez Luci, niestety. Po każdym restarcie wszystkie diody świecą i to koniec. Podłączyłam się przez konsolę:
picocom --baud 115200 --flow=none --parity=none --databits 8 /dev/ttyUSB0
picocom v1.7
port is : /dev/ttyUSB0
flowcontrol : none
baudrate is : 115200
parity is : none
databits are : 8
escape is : C-a
local echo is : no
noinit is : no
noreset is : no
nolock is : no
send_cmd is : sz -vv
receive_cmd is : rz -vv
imap is :
omap is :
emap is : crcrlf,delbs,
Terminal ready
ROM VER: 1.0.3
CFG 01
Read�
ROM VER: 1.0.3
CFG 01
Read EEPROMX
X
U-Boot 2010.03 (May 11 2012 - 02:54:15)
Board: ARV4518PW
SoC: Danube/Twinpass/Vinax-VE V1.5, DDR Speed 166 MHz, CPU Speed 333 MHz
DRAM: 64 MB
Flash: 8 MB
*** Warning - bad CRC, using default environment
Net:
searching for rtl8306 switch ... found
lq_cpe_eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0020000 ...
Image Name: MIPS OpenWrt Linux-3.18.23
Created: 2016-02-02 12:42:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1530657 Bytes = 1.5 MB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 12:02:45 CET 2016
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ARV752DPW22 - Arcor 803
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000008
[ 0.000000] Readback ErrCtl register=00000008
[ 0.000000] Memory: 60144K/65536K available (3433K kernel code, 151K rwdata, 768K rodata, 172K init, 194K bss, 5392K reserved)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.052000] pinctrl core: initialized pinctrl subsystem
[ 0.060000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.084000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.088000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.092000] IO 0x000000001ae00000..0x000000001affffff
[ 0.108000] usbcore: registered new interface driver usbfs
[ 0.112000] usbcore: registered new interface driver hub
[ 0.116000] usbcore: registered new device driver usb
[ 0.120000] PCI host bridge to bus 0000:00
[ 0.124000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.128000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.132000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.136000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.140000] Switched to clocksource MIPS
[ 0.144000] NET: Registered protocol family 2
[ 0.152000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.160000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.164000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.172000] TCP: reno registered
[ 0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] NET: Registered protocol family 1
[ 0.192000] gptu: totally 6 16-bit timers/counters
[ 0.196000] gptu: misc_register on minor 63
[ 0.200000] gptu: succeeded to request irq 126
[ 0.208000] gptu: succeeded to request irq 127
[ 0.212000] gptu: succeeded to request irq 128
[ 0.216000] gptu: succeeded to request irq 129
[ 0.220000] gptu: succeeded to request irq 130
[ 0.224000] gptu: succeeded to request irq 131
[ 0.236000] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[ 0.240000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[ 0.248000] ralink,eeprom ralink_eep: using RT2860.eeprom as eeprom
[ 0.256000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.268000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.272000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.300000] msgmni has been set to 117
[ 0.308000] io scheduler noop registered
[ 0.312000] io scheduler deadline registered (default)
[ 0.320000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.328000] console [ttyLTQ0] enabled
[ 0.328000] console [ttyLTQ0] enabled
[ 0.336000] bootconsole [early0] disabled
[ 0.336000] bootconsole [early0] disabled
[ 0.344000] lantiq nor flash device: 00800000 at 10000000
[ 0.348000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.356000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.364000] Amd/Fujitsu Extended Query version 1.1.
[ 0.368000] number of CFI chips: 1
[ 0.372000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.376000] Creating 4 MTD partitions on "ltq_nor":
[ 0.380000] 0x000000000000-0x000000030000 : "uboot"
[ 0.388000] 0x000000030000-0x000000040000 : "uboot_env"
[ 0.392000] 0x000000040000-0x0000007f0000 : "firmware"
[ 0.556000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.588000] libphy: ltq_mii: probed
[ 0.684000] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
[ 0.688000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.700000] wdt 1f8803f0.watchdog: Init done
[ 0.708000] TCP: cubic registered
[ 0.712000] NET: Registered protocol family 17
[ 0.716000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.728000] Bridge firewalling registered
[ 0.732000] 8021q: 802.1Q VLAN Support v1.8
[ 0.740000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 0.748000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 0.752000] Please append a correct "root=" boot option; here are the available partitions:
[ 0.760000] 1f00 192 mtdblock0 (driver?)
[ 0.768000] 1f01 64 mtdblock1 (driver?)
[ 0.772000] 1f02 7872 mtdblock2 (driver?)
[ 0.776000] 1f03 64 mtdblock3 (driver?)
[ 0.780000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 0.780000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 33.092000] random: nonblocking pool is initialized
ARV4518 => printenv
bootcmd=run flash_flash
bootdelay=2
baudrate=115200
loads_echo=
ipaddr=192.168.144.99
serverip=192.168.144.100
rootpath="/export"
gatewayip=192.168.144.1
netmask=255.255.255.0
ram_addr=0x80500000
kernel_addr=0xb0020000
flashargs=setenv bootargs rootfstype=squashfs,jffs2
nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}
addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off
addmisc=setenv bootargs ${bootargs} init=/etc/preinit console=ttyS1,115200 ethaddr=${ethaddr} ${mtdparts}
flash_flash=run flashargs addip addmisc;bootm ${kernel_addr}
flash_nfs=run nfsargs addip addmisc;bootm ${kernel_addr}
net_flash=run load_kernel flashargs addip addmisc;bootm ${ram_addr}
net_nfs=run load_kernel nfsargs addip addmisc;bootm ${ram_addr}
load_kernel=tftp ${ram_addr} ${tftppath}openwrt-ifxmips-uImage
update_uboot=tftp 0x80500000 ${tftppath}u-boot-ARV4518PW.bin;era 0xb0000000 +${filesize};cp.b 0x80500000 0xb0000000 ${filesize}
update_openwrt=tftp ${ram_addr} ${tftppath}ARV4518PW-squashfs.image;era ${kernel_addr} +${filesize};cp.b ${ram_addr} ${kernel_addr} ${filesize}
stdin=serial
stdout=serial
stderr=serial
ethaddr=28:1f:05:bd:29:23
ethact=lq_cpe_eth
ver=U-Boot 2010.03 (May 11 2012 - 02:54:15)
Environment size: 1274/65532 bytes
ARV4518 =>
ARV4518 => ?
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
erase - erase FLASH memory
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print command description/usage
iminfo - print header information for application image
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mm - memory modify (auto-incrementing address)
mtest - simple RAM read/write test
mw - memory write (fill)
nm - memory modify (constant address)
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
tftpboot- boot image via network using TFTP protocol
version - print monitor version
ARV4518 => run update_openwrt
Using lq_cpe_eth device
TFTP from server 192.168.144.100; our IP address is 192.168.144.99
Filename 'ARV4518PW-squashfs.image'.
Load address: 0x80500000
Loading: T T T T T T T T T T NO Tx Descriptor...T NO Tx Descriptor...NO Tx Descriptor...T NO Tx Descriptor...NO Tx Descriptor...T NO Tx Descriptor...
Abort
Co dalej? Da się uratować jakoś?
