Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → TP-Link Archer C7 v2+Huawei E3372h
Strony Poprzednia 1 2
Zaloguj się lub zarejestruj by napisać odpowiedź
Masz i PLAY i wan i ORANGE. Usuń dwa i zostaw jedno samo wan. Druga sprawa - usuń opcję mode oraz ipv6. zakładam że pin faktycznie masz 1234 (bo jak nie to już zablokowałeś kartę). Zrestartuj router, poczekaj ze 3 minuty i pokaż wynik poleceń:
logread
ifstatus wan
ifstatus wan_4
Masz i PLAY i wan i ORANGE. Usuń dwa i zostaw jedno samo wan. Druga sprawa - usuń opcję mode oraz ipv6. zakładam że pin faktycznie masz 1234 (bo jak nie to już zablokowałeś kartę). Zrestartuj router, poczekaj ze 3 minuty i pokaż wynik poleceń:
logread
ifstatus wan
ifstatus wan_4
Pin nie zablokował karty. Modem w Windows działa bez zająknięcia.
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.000000] Linux version 3.18.44 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46943) ) #7 Fri Nov 11 13:59:20 CET 2016
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] MyLoader: sysp=bab3a22a, boardp=6aaaa282, parts=a2a2a22b
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] SoC: Atheros AR9132 rev 2
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Determined physical RAM map:
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] memory: 02000000 @ 00000000 (usable)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Zone ranges:
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Normal [mem 0x00000000-0x01ffffff]
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Movable zone start for each node
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Early memory node ranges
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 8038a2b0, node_mem_map 81000000
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] Normal zone: 8192 pages, LIFO batch:0
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.000000] Memory: 28260K/32768K available (2651K kernel code, 146K rwdata, 556K rodata, 220K init, 193K bss, 4508K reserved)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] NR_IRQS:51
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.100000] NET: Registered protocol family 16
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.390000] Switched to clocksource MIPS
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.390000] NET: Registered protocol family 2
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.400000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.400000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.410000] TCP: Hash tables configured (established 1024 bind 1024)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.420000] TCP: reno registered
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.420000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.430000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.430000] NET: Registered protocol family 1
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 0.440000] PCI: CLS 0 bytes, default 32
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.440000] futex hash table entries: 256 (order: -1, 3072 bytes)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.460000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.470000] msgmni has been set to 55
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.480000] io scheduler noop registered
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.480000] io scheduler deadline registered (default)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.480000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.490000] console [ttyS0] disabled
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.520000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.530000] console [ttyS0] enabled
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.530000] bootconsole [early0] disabled
Thu Jan 4 13:39:15 2018 kern.warn kernel: [ 0.540000] m25p80 spi0.0: found s25sl064p, expected m25p80
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.550000] m25p80 spi0.0: s25sl064p (8192 Kbytes)
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.560000] 5 tp-link partitions found on MTD device spi0.0
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.560000] Creating 5 MTD partitions on "spi0.0":
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.570000] 0x000000000000-0x000000020000 : "u-boot"
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.570000] 0x000000020000-0x000000148600 : "kernel"
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.580000] 0x000000148600-0x0000007f0000 : "rootfs"
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.580000] mtd: device 2 (rootfs) set to be root filesystem
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.590000] 1 squashfs-split partitions found on MTD device rootfs
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.600000] 0x000000670000-0x0000007f0000 : "rootfs_data"
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.600000] 0x0000007f0000-0x000000800000 : "art"
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.610000] 0x000000020000-0x0000007f0000 : "firmware"
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 0.620000] Realtek RTL8366RB ethernet switch driver version 0.2.4
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.730000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.730000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 0.920000] libphy: rtl8366rb: probed
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.240000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.240000] TCP: cubic registered
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.250000] NET: Registered protocol family 17
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.250000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 1.270000] Bridge firewalling registered
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.270000] 8021q: 802.1Q VLAN Support v1.8
Thu Jan 4 13:39:15 2018 kern.err kernel: [ 1.280000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.290000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 1.300000] Freeing unused kernel memory: 220K (803a9000 - 803e0000)
Thu Jan 4 13:39:15 2018 user.info kernel: [ 2.830000] init: Console is alive
Thu Jan 4 13:39:15 2018 user.info kernel: [ 2.840000] init: - watchdog -
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.440000] usbcore: registered new interface driver usbfs
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.450000] usbcore: registered new interface driver hub
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.460000] usbcore: registered new device driver usb
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 5.500000] SCSI subsystem initialized
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.510000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.520000] ehci-platform: EHCI generic platform driver
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.530000] ehci-platform ehci-platform: EHCI Host Controller
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.530000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.540000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.570000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.570000] hub 1-0:1.0: USB hub found
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.580000] hub 1-0:1.0: 1 port detected
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.580000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.590000] ohci-platform: OHCI generic platform driver
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.600000] usbcore: registered new interface driver usb-storage
Thu Jan 4 13:39:15 2018 user.info kernel: [ 5.850000] init: - preinit -
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 5.940000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 6.460000] random: procd urandom read with 10 bits of entropy available
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 6.530000] usb-storage 1-1:1.3: USB Mass Storage device detected
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 6.550000] scsi host0: usb-storage 1-1:1.3
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 6.560000] usb-storage 1-1:1.4: USB Mass Storage device detected
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 6.570000] scsi host1: usb-storage 1-1:1.4
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 6.690000] ar71xx: pll_reg 0xb8050014: 0x1a000000
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 6.690000] eth0: link up (1000Mbps/Full duplex)
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 7.560000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 7.580000] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 7.590000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Thu Jan 4 13:39:15 2018 user.info kernel: [ 9.990000] mount_root: loading kmods from internal overlay
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 10.290000] jffs2: notice: (413) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.310000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.330000] block: extroot: not configured
Thu Jan 4 13:39:15 2018 kern.notice kernel: [ 10.390000] jffs2: notice: (410) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.410000] mount_root: loading kmods from internal overlay
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.580000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.600000] block: extroot: not configured
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.600000] mount_root: switching to jffs2 overlay
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 10.650000] eth0: link down
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.660000] procd: - early -
Thu Jan 4 13:39:15 2018 user.info kernel: [ 10.670000] procd: - watchdog -
Thu Jan 4 13:39:15 2018 user.info kernel: [ 11.700000] procd: - ubus -
Thu Jan 4 13:39:15 2018 user.info kernel: [ 12.730000] procd: - init -
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.740000] NET: Registered protocol family 10
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.790000] gre: GRE over IPv4 demultiplexor driver
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.800000] ip_gre: GRE over IPv4 tunneling driver
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.820000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.890000] u32 classifier
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.890000] input device check on
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.890000] Actions configured
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.900000] Mirror/redirect action on
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.970000] fuse init (API version 7.23)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 15.990000] usbcore: registered new interface driver cdc_acm
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.000000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.010000] usbcore: registered new interface driver cdc_wdm
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.020000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.030000] Backport generated by backports.git backports-20151218-0-g2f58d9d
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.040000] ip_tables: (C) 2000-2006 Netfilter Core Team
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.080000] nf_conntrack version 0.5.0 (445 buckets, 1780 max)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.130000] usbcore: registered new interface driver usblp
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.150000] usbcore: registered new interface driver usbserial
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.160000] usbcore: registered new interface driver usbserial_generic
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.160000] usbserial: USB Serial support registered for generic
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.240000] xt_time: kernel timezone is -0000
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.250000] usbcore: registered new interface driver cdc_ether
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.260000] usbcore: registered new interface driver cdc_ncm
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.400000] huawei_cdc_ncm 1-1:1.2: MAC-Address: 00:1e:10:1f:00:00
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.410000] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.420000] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.430000] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.440000] huawei_cdc_ncm 1-1:1.2 wwan0: register 'huawei_cdc_ncm' at usb-ehci-platform-1, Huawei CDC NCM device, 00:1e:10:1f:00:00
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.450000] usbcore: registered new interface driver huawei_cdc_ncm
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.560000] PPP generic driver version 2.4.2
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.570000] PPP MPPE Compression module registered
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.570000] NET: Registered protocol family 24
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.580000] PPTP driver version 0.8.5
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.600000] usbcore: registered new interface driver qmi_wwan
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.610000] usbcore: registered new interface driver rndis_host
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.630000] usbcore: registered new interface driver sierra
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.630000] usbserial: USB Serial support registered for Sierra USB modem
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.640000] usbcore: registered new interface driver sierra_net
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.730000] usbcore: registered new interface driver cdc_mbim
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.740000] usbcore: registered new interface driver option
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.740000] usbserial: USB Serial support registered for GSM modem (1-port)
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.750000] option 1-1:1.0: GSM modem (1-port) converter detected
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.760000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.770000] option 1-1:1.1: GSM modem (1-port) converter detected
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.770000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.790000] usbcore: registered new interface driver qcserial
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.790000] usbserial: USB Serial support registered for Qualcomm USB modem
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.840000] ath: EEPROM regdomain: 0x0
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.840000] ath: EEPROM indicates default country code should be used
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.840000] ath: doing EEPROM country->regdmn map search
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.840000] ath: country maps to regdmn code: 0x3a
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.840000] ath: Country alpha2 being used: US
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.840000] ath: Regpair used: 0x3a
Thu Jan 4 13:39:15 2018 kern.debug kernel: [ 16.860000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Thu Jan 4 13:39:15 2018 kern.info kernel: [ 16.870000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
Thu Jan 4 13:39:19 2018 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Thu Jan 4 13:39:20 2018 daemon.err block: /dev/mtdblock3 is already mounted
Thu Jan 4 13:39:20 2018 cron.info crond[1365]: crond (busybox 1.23.2) started, log level 8
Thu Jan 4 13:39:22 2018 kern.debug kernel: [ 27.150000] ar71xx: pll_reg 0xb8050014: 0x1a000000
Thu Jan 4 13:39:22 2018 kern.info kernel: [ 27.150000] eth0: link up (1000Mbps/Full duplex)
Thu Jan 4 13:39:22 2018 kern.info kernel: [ 27.160000] device eth0.1 entered promiscuous mode
Thu Jan 4 13:39:22 2018 kern.info kernel: [ 27.170000] device eth0 entered promiscuous mode
Thu Jan 4 13:39:22 2018 kern.info kernel: [ 27.180000] br-lan: port 1(eth0.1) entered forwarding state
Thu Jan 4 13:39:22 2018 kern.info kernel: [ 27.180000] br-lan: port 1(eth0.1) entered forwarding state
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'lan' is enabled
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'lan' is setting up now
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'lan' is now up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'loopback' is enabled
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'loopback' is now up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'wan6' is enabled
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Bridge 'br-lan' link is up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Network device 'eth0' link is up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: VLAN 'eth0.1' link is up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Network device 'lo' link is up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Jan 4 13:39:22 2018 daemon.notice netifd: VLAN 'eth0.2' link is up
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'wan6' has link connectivity
Thu Jan 4 13:39:22 2018 daemon.notice netifd: Interface 'wan6' is setting up now
Thu Jan 4 13:39:23 2018 daemon.warn odhcpd[1319]: DHCPV6 SOLICIT IA_NA from 000100011a1057e194de80a59906 on br-lan: ok XXXX:XXXX:XXXX::180/128
Thu Jan 4 13:39:24 2018 daemon.warn odhcpd[1319]: DHCPV6 SOLICIT IA_NA from 000100011a1057e194de80a59906 on br-lan: ok XXXX:XXXX:XXXX::180/128
Thu Jan 4 13:39:24 2018 daemon.warn odhcpd[1319]: DHCPV6 REQUEST IA_NA from 000100011a1057e194de80a59906 on br-lan: ok XXXX:XXXX:XXXX::180/128
Thu Jan 4 13:39:24 2018 kern.info kernel: [ 29.180000] br-lan: port 1(eth0.1) entered forwarding state
Thu Jan 4 13:39:25 2018 authpriv.info dropbear[1484]: Not backgrounding
Thu Jan 4 13:39:27 2018 daemon.notice netifd: wan (1410): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:39:28 2018 daemon.notice netifd: radio0 (1412): Configuration file: /var/run/hostapd-phy0.conf
Thu Jan 4 13:39:28 2018 kern.info kernel: [ 32.430000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Thu Jan 4 13:39:28 2018 daemon.notice netifd: wan (1410): sending ->
Thu Jan 4 13:39:28 2018 daemon.notice netifd: radio0 (1412): wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Jan 4 13:39:28 2018 kern.info kernel: [ 32.530000] device wlan0 entered promiscuous mode
Thu Jan 4 13:39:28 2018 daemon.notice netifd: radio0 (1412): Using interface wlan0 with hwaddr b0:48:7a:d2:fc:82 and ssid "LU1043"
Thu Jan 4 13:39:28 2018 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Jan 4 13:39:31 2018 daemon.notice netifd: radio0 (1412): wlan0: interface state COUNTRY_UPDATE->ENABLED
Thu Jan 4 13:39:31 2018 daemon.notice netifd: radio0 (1412): wlan0: AP-ENABLED
Thu Jan 4 13:39:31 2018 kern.info kernel: [ 36.040000] br-lan: port 2(wlan0) entered forwarding state
Thu Jan 4 13:39:31 2018 kern.info kernel: [ 36.040000] br-lan: port 2(wlan0) entered forwarding state
Thu Jan 4 13:39:31 2018 kern.info kernel: [ 36.050000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Thu Jan 4 13:39:32 2018 daemon.notice netifd: Network device 'wlan0' link is up
Thu Jan 4 13:39:33 2018 kern.info kernel: [ 38.040000] br-lan: port 2(wlan0) entered forwarding state
Thu Jan 4 13:39:35 2018 user.emerg syslog: setting up led USB
Thu Jan 4 13:39:35 2018 user.emerg syslog: setting up led WLAN
Thu Jan 4 13:39:35 2018 daemon.info procd: - init complete -
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq[2180]: started, version 2.73 cachesize 150
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq[2180]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq[2180]: DNS service limited to local subnets
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq-dhcp[2180]: DHCP, static leases only on 192.168.48.100, lease time 12h
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq[2180]: using local addresses only for domain lan
Thu Jan 4 13:39:37 2018 daemon.warn dnsmasq[2180]: no servers found in /tmp/resolv.conf.auto, will retry
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq[2180]: read /etc/hosts - 33 addresses
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq[2180]: read /tmp/hosts/dhcp - 1 addresses
Thu Jan 4 13:39:37 2018 daemon.info dnsmasq-dhcp[2180]: read /etc/ethers - 0 addresses
Thu Jan 4 13:39:43 2018 daemon.notice netifd: wan (1410): Timeout running AT-command
Thu Jan 4 13:39:43 2018 daemon.notice netifd: wan (1410): Failed to set operating mode
Thu Jan 4 13:39:43 2018 daemon.notice netifd: wan (2303): Stopping network
Thu Jan 4 13:39:45 2018 kern.notice kernel: [ 49.670000] random: nonblocking pool is initialized
Thu Jan 4 13:39:45 2018 daemon.notice netifd: wan (2303): sending ->
Thu Jan 4 13:39:48 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:39:48 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:39:50 2018 daemon.notice netifd: wan (2313): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:39:50 2018 daemon.notice netifd: wan (2313): sending ->
Thu Jan 4 13:39:53 2018 daemon.info dnsmasq-dhcp[2180]: DHCPREQUEST(br-lan) 192.168.48.180 XXXX:XXXX:XXXX
Thu Jan 4 13:39:53 2018 daemon.info dnsmasq-dhcp[2180]: DHCPACK(br-lan) 192.168.48.180 XXXX:XXXX:XXXX XXXXXXX
Thu Jan 4 13:39:55 2018 authpriv.info dropbear[2327]: Child connection from 192.168.48.180:50513
Thu Jan 4 13:40:05 2018 authpriv.notice dropbear[2327]: Password auth succeeded for 'root' from 192.168.48.180:50513
Thu Jan 4 13:40:05 2018 daemon.notice netifd: wan (2313): Timeout running AT-command
Thu Jan 4 13:40:05 2018 daemon.notice netifd: wan (2313): Failed to set operating mode
Thu Jan 4 13:40:06 2018 daemon.notice netifd: wan (2401): Stopping network
Thu Jan 4 13:40:08 2018 daemon.notice netifd: wan (2401): sending ->
Thu Jan 4 13:40:10 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:40:10 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:40:12 2018 daemon.notice netifd: wan (2421): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:40:13 2018 daemon.notice netifd: wan (2421): sending ->
Thu Jan 4 13:40:28 2018 daemon.notice netifd: wan (2421): Timeout running AT-command
Thu Jan 4 13:40:28 2018 daemon.notice netifd: wan (2421): Failed to set operating mode
Thu Jan 4 13:40:28 2018 daemon.notice netifd: wan (2439): Stopping network
Thu Jan 4 13:40:30 2018 daemon.notice netifd: wan (2439): sending ->
Thu Jan 4 13:40:33 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:40:33 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:40:35 2018 daemon.notice netifd: wan (2447): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:40:35 2018 daemon.notice netifd: wan (2447): sending ->
Thu Jan 4 13:40:50 2018 daemon.notice netifd: wan (2447): Timeout running AT-command
Thu Jan 4 13:40:50 2018 daemon.notice netifd: wan (2447): Failed to set operating mode
Thu Jan 4 13:40:50 2018 daemon.notice netifd: wan (2468): Stopping network
Thu Jan 4 13:40:53 2018 daemon.notice netifd: wan (2468): sending ->
Thu Jan 4 13:40:55 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:40:55 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:40:57 2018 daemon.notice netifd: wan (2478): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:40:58 2018 daemon.notice netifd: wan (2478): sending ->
Thu Jan 4 13:41:13 2018 daemon.notice netifd: wan (2478): Timeout running AT-command
Thu Jan 4 13:41:13 2018 daemon.notice netifd: wan (2478): Failed to set operating mode
Thu Jan 4 13:41:13 2018 daemon.notice netifd: wan (2495): Stopping network
Thu Jan 4 13:41:15 2018 daemon.notice netifd: wan (2495): sending ->
Thu Jan 4 13:41:18 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:41:18 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:41:20 2018 daemon.notice netifd: wan (2503): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:41:20 2018 daemon.notice netifd: wan (2503): sending ->
Thu Jan 4 13:41:35 2018 daemon.notice netifd: wan (2503): Timeout running AT-command
Thu Jan 4 13:41:35 2018 daemon.notice netifd: wan (2503): Failed to set operating mode
Thu Jan 4 13:41:35 2018 daemon.notice netifd: wan (2521): Stopping network
Thu Jan 4 13:41:37 2018 daemon.notice netifd: wan (2521): sending ->
Thu Jan 4 13:41:40 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:41:40 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:41:42 2018 daemon.notice netifd: wan (2529): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:41:43 2018 daemon.notice netifd: wan (2529): sending ->
Thu Jan 4 13:41:55 2018 authpriv.info dropbear[2327]: Exit (root): Exited normally
Thu Jan 4 13:41:58 2018 daemon.notice netifd: wan (2529): Timeout running AT-command
Thu Jan 4 13:41:58 2018 daemon.notice netifd: wan (2529): Failed to set operating mode
Thu Jan 4 13:41:58 2018 daemon.notice netifd: wan (2546): Stopping network
Thu Jan 4 13:42:00 2018 daemon.notice netifd: wan (2546): sending ->
Thu Jan 4 13:42:02 2018 authpriv.info dropbear[2554]: Child connection from 192.168.48.180:50520
Thu Jan 4 13:42:03 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:42:03 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:42:05 2018 daemon.notice netifd: wan (2555): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:42:05 2018 daemon.notice netifd: wan (2555): sending ->
Thu Jan 4 13:42:11 2018 authpriv.notice dropbear[2554]: Password auth succeeded for 'root' from 192.168.48.180:50520
Thu Jan 4 13:42:20 2018 daemon.notice netifd: wan (2555): Timeout running AT-command
Thu Jan 4 13:42:20 2018 daemon.notice netifd: wan (2555): Failed to set operating mode
Thu Jan 4 13:42:20 2018 daemon.notice netifd: wan (2654): Stopping network
Thu Jan 4 13:42:22 2018 daemon.notice netifd: wan (2654): sending ->
Thu Jan 4 13:42:25 2018 daemon.notice netifd: Interface 'wan' is now down
Thu Jan 4 13:42:25 2018 daemon.notice netifd: Interface 'wan' is setting up now
Thu Jan 4 13:42:27 2018 daemon.notice netifd: wan (2662): WARNING: Variable 'modes' does not exist or is not an array/object
Thu Jan 4 13:42:27 2018 daemon.notice netifd: wan (2662): sending ->
Thu Jan 4 13:42:43 2018 daemon.notice netifd: wan (2662): Timeout running AT-command
Thu Jan 4 13:42:43 2018 daemon.notice netifd: wan (2662): Failed to set operating mode
Thu Jan 4 13:42:43 2018 daemon.notice netifd: wan (2681): Stopping network
Thu Jan 4 13:42:45 2018 daemon.notice netifd: wan (2681): sending -> root@LuCI:~# ifstatus wan
{
"up": false,
"pending": true,
"available": true,
"autostart": true,
"dynamic": false,
"proto": "ncm",
"data": {
}
}
root@LuCI:~# ifstatus wan_4
Interface wan_4 not found 1. czy masz zainstalowany comgt-ncm?
2. Zmień interfejs na /dev/ttyUSB1 lub /dev/cdc-wdm0 i ponownie: reboot i pokaż w/w polecenia.
EDIT: wykonaj jeszcze
gcom -d "/dev/ttyUSB0" -s /etc/gcom/getcardinfo.gcom
gcom -d "/dev/ttyUSB1" -s /etc/gcom/getcardinfo.gcomI też pokaż co wyszło.
1. czy masz zainstalowany comgt-ncm?
2. Zmień interfejs na /dev/ttyUSB1 lub /dev/cdc-wdm0 i ponownie: reboot i pokaż w/w polecenia.EDIT: wykonaj jeszcze
gcom -d "/dev/ttyUSB0" -s /etc/gcom/getcardinfo.gcom gcom -d "/dev/ttyUSB1" -s /etc/gcom/getcardinfo.gcomI też pokaż co wyszło.
Dziwne. Po usunięciu interfejsów PLAY i ORANGE, wypięciu modemu i podłączeniu do Windows na czas naszej komunikacji na forum, a następnie po podączeniu do routera, wreszcie modem odpalił.
Czy problem był w konflikcie dwóch interfejsó opartych na wan, czy zakłócenia przez interfejs PLAY?
PLAY jest mi potrzebny, bo zamiennie wkładam modem E3272s-153 (PLAY) w trybie nocnym i E3372h-153 (ORANGE) w trybie dziennym.
Tylko dla porządku:
root@LuCI:~# opkg list-installed |grep comgt
comgt - 0.32-25
comgt-directip - 0.32-25
comgt-ncm - 0.32-25
root@LuCI:~# ifstatus wan
{
"up": true,
"pending": false,
"available": true,
"autostart": true,
"dynamic": false,
"uptime": 241,
"l3_device": "wwan0",
"proto": "ncm",
"metric": 0,
"delegation": false,
"ipv4-address": [
],
"ipv6-address": [
],
"ipv6-prefix": [
],
"ipv6-prefix-assignment": [
],
"route": [
],
"dns-server": [
],
"dns-search": [
],
"inactive": {
"ipv4-address": [
],
"ipv6-address": [
],
"route": [
],
"dns-server": [
],
"dns-search": [
]
},
"data": {
}
}
root@LuCI:~# ifstatus wan
{
"up": true,
"pending": false,
"available": true,
"autostart": true,
"dynamic": false,
"uptime": 273,
"l3_device": "wwan0",
"proto": "ncm",
"metric": 0,
"delegation": false,
"ipv4-address": [
],
"ipv6-address": [
],
"ipv6-prefix": [
],
"ipv6-prefix-assignment": [
],
"route": [
],
"dns-server": [
],
"dns-search": [
],
"inactive": {
"ipv4-address": [
],
"ipv6-address": [
],
"route": [
],
"dns-server": [
],
"dns-search": [
]
},
"data": {
}
}
root@LuCI:~#
root@LuCI:~# gcom -d "/dev/ttyUSB0" -s /etc/gcom/getcardinfo.gcom
ATI
Manufacturer: huawei
Model: MegaFon M150-2
Revision: 21.200.07.00.209
IMEI: XXXXXXXXXXXXXXX
+GCAP: +CGSM,+DS,+ES
OK
root@LuCI:~# gcom -d "/dev/ttyUSB1" -s /etc/gcom/getcardinfo.gcom
ATI
Manufacturer: huawei
Model: MegaFon M150-2
Revision: 21.200.07.00.209
IMEI: XXXXXXXXXXXXXXX
+GCAP: +CGSM,+DS,+ES
OKI niby dlaczego potrzebujesz obu sekcji jak dla obu modemów możesz ustawić ncm i /dev/ttyUSB0, bo taki interfejs miałeś dla wszystkich trzech sekcji?
network.PLAY=interface
network.PLAY.proto='3g'
network.PLAY.device='/dev/ttyUSB0'
network.PLAY.service='umts'
network.PLAY.apn='internet'
network.PLAY.ipv6='auto'Dla Play (E3272s-153) miałem 3g a nie ncm.
Z twojego podadnika wynika, że ncm może być dla E3272s-153, E3372s-153 i E3372h-153.
W nocy sprawdzę, czy działa dla obu modemów jedno ustawienie wan.
Bardzo Ci dziękuję za wsparcie. Jesteś niezastąpiony i niesamowicie uczynny. Pomyślnego Nowego Roku!
Działa ncm dla E3272, sam ich jeszcze mam kilkanaście w robocie.
Strony Poprzednia 1 2
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → TP-Link Archer C7 v2+Huawei E3372h
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc