• Skąd: Warszawa
  • Zarejestrowany: 2011-10-22
  • Posty: 10

Temat: Openwrt dla netiaspot

Pomijając fakt że 95%  - 98% urządzeń netiaspot to sprzęty dzierżawione użytkownikom , to jednak troszkę tych "własnościowych"  już jest. Zresztą każdy użytkownik ma w umowie "cenę" spota jeśli go nie odda lub odda uszkodzonego.
Może ktoś z Was pomógł by postawić na spocie opnwrt + luci.
Platforma na której bazuje spot to procesor firmy lantiq  ARX168.
Router ten wyposażony jest w 1 port ADSL, 3 porty LAN i 1 port WAN oraz 2 porty USB 2.0
Jestem w stanie zapewnić urządzenie do testów.

Zamieszczam log z uruchomienia systemu:

Pozdrawiam.



=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.12.27 21:07:30 =~=~=~=~=~=~=~=~=~=~=~=
     
ROM VER: 1.1.3
CFG 05

ROM VER: 1.1.3
CFG 05
DDR Access auto data-eye tuning Rev 0.3a
DDR size from 0xa0000000 - 0xa1ffffff
DDR check ok... start booting...



U-Boot 1.1.5-LANTIQ-v-1.8.39 (Apr  4 2011 - 19:51:54)

Boot from SPI
AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  32 MB

relocate_code start
relocate_code finish.
64 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:    Start init xR9 Mac 0 to 2 mode
GPIO25 reset to Eth switch is generated.

switch chip id=00002599
Tantos Switch detected!!

amazon_s Switch

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  1  0

NAND read: device 0 offset 0x0, size 0x400000 ...

Reading data from 0x0 --   0% complete.
Reading data from 0xa200 --   1% complete.
Reading data from 0x14600 --   2% complete.
Reading data from 0x1ea00 --   3% complete.
Reading data from 0x28e00 --   4% complete.
Reading data from 0x33200 --   5% complete.
Reading data from 0x3d600 --   6% complete.
Reading data from 0x47a00 --   7% complete.
Reading data from 0x51e00 --   8% complete.
Reading data from 0x5c200 --   9% complete.
Reading data from 0x66600 --  10% complete.
Reading data from 0x70a00 --  11% complete.
Reading data from 0x7ae00 --  12% complete.
Reading data from 0x85000 --  13% complete.
Reading data from 0x8f400 --  14% complete.
Reading data from 0x99800 --  15% complete.
Reading data from 0xa3c00 --  16% complete.
Reading data from 0xae000 --  17% complete.
Reading data from 0xb8400 --  18% complete.
Reading data from 0xc2800 --  19% complete.
Reading data from 0xccc00 --  20% complete.
Reading data from 0xd7000 --  21% complete.
Reading data from 0xe1400 --  22% complete.
Reading data from 0xeb800 --  23% complete.
Reading data from 0xf5c00 --  24% complete.
Reading data from 0xffe00 --  25% complete.
Reading data from 0x10a200 --  26% complete.
Reading data from 0x114600 --  27% complete.
Reading data from 0x11ea00 --  28% complete.
Reading data from 0x128e00 --  29% complete.
Reading data from 0x133200 --  30% complete.
Reading data from 0x13d600 --  31% complete.
Reading data from 0x147a00 --  32% complete.
Reading data from 0x151e00 --  33% complete.
Reading data from 0x15c200 --  34% complete.
Reading data from 0x166600 --  35% complete.
Reading data from 0x170a00 --  36% complete.
Reading data from 0x17ae00 --  37% complete.
Reading data from 0x185000 --  38% complete.
Reading data from 0x18f400 --  39% complete.
Reading data from 0x199800 --  40% complete.
Reading data from 0x1a3c00 --  41% complete.
Reading data from 0x1ae000 --  42% complete.
Reading data from 0x1b8400 --  43% complete.
Reading data from 0x1c2800 --  44% complete.
Reading data from 0x1ccc00 --  45% complete.
Reading data from 0x1d7000 --  46% complete.
Reading data from 0x1e1400 --  47% complete.
Reading data from 0x1eb800 --  48% complete.
Reading data from 0x1f5c00 --  49% complete.
Reading data from 0x1ffe00 --  50% complete.
Reading data from 0x20a200 --  51% complete.
Reading data from 0x214600 --  52% complete.
Reading data from 0x21ea00 --  53% complete.
Reading data from 0x228e00 --  54% complete.
Reading data from 0x233200 --  55% complete.
Reading data from 0x23d600 --  56% complete.
Reading data from 0x247a00 --  57% complete.
Reading data from 0x251e00 --  58% complete.
Reading data from 0x25c200 --  59% complete.
Reading data from 0x266600 --  60% complete.
Reading data from 0x270a00 --  61% complete.
Reading data from 0x27ae00 --  62% complete.
Reading data from 0x285000 --  63% complete.
Reading data from 0x28f400 --  64% complete.
Reading data from 0x299800 --  65% complete.
Reading data from 0x2a3c00 --  66% complete.
Reading data from 0x2ae000 --  67% complete.
Reading data from 0x2b8400 --  68% complete.
Reading data from 0x2c2800 --  69% complete.
Reading data from 0x2ccc00 --  70% complete.
Reading data from 0x2d7000 --  71% complete.
Reading data from 0x2e1400 --  72% complete.
Reading data from 0x2eb800 --  73% complete.
Reading data from 0x2f5c00 --  74% complete.
Reading data from 0x2ffe00 --  75% complete.
Reading data from 0x30a200 --  76% complete.
Reading data from 0x314600 --  77% complete.
Reading data from 0x31ea00 --  78% complete.
Reading data from 0x328e00 --  79% complete.
Reading data from 0x333200 --  80% complete.
Reading data from 0x33d600 --  81% complete.
Reading data from 0x347a00 --  82% complete.
Reading data from 0x351e00 --  83% complete.
Reading data from 0x35c200 --  84% complete.
Reading data from 0x366600 --  85% complete.
Reading data from 0x370a00 --  86% complete.
Reading data from 0x37ae00 --  87% complete.
Reading data from 0x385000 --  88% complete.
Reading data from 0x38f400 --  89% complete.
Reading data from 0x399800 --  90% complete.
Reading data from 0x3a3c00 --  91% complete.
Reading data from 0x3ae000 --  92% complete.
Reading data from 0x3b8400 --  93% complete.
Reading data from 0x3c2800 --  94% complete.
Reading data from 0x3ccc00 --  95% complete.
Reading data from 0x3d7000 --  96% complete.
Reading data from 0x3e1400 --  97% complete.
Reading data from 0x3eb800 --  98% complete.
Reading data from 0x3f5c00 --  99% complete.
Reading data from 0x3ffe00 -- 100% complete.
OK
## Starting application at 0x80C00000 ...


Uncompressing Linux...

malloc: 00003E6C

returned: 80E92020

..................................................................................................

Done

Network boot detected: move image to proper location

Running from : (0x80C00008) CramFS will be at: 0x803AD000

Booting the kernel

dcache writeback, cachesize 00004000 linesize 00000020

icache invalidate, cachesize 00008000 linesize 00000020

Infineon xDSL CPE AR9
mips_hpt_frequency = 166666666, counter_resolution = 2
Linux version 2.6.21.5 #1 Tue Mar 29 09:07:41 IST 2011
rofs_addr: 00225000 (80225000), len: f0000, flash_start_addr: 00000000 (80000000) flash_len: 0
CramFS found in RAM
rofs_start_addr: 00000000 len: 0
phym = 01000000, mem = 00f00000, max_pfn = 00000f00
Reserving memory for CP1 @0xa0f00000, size 0x00100000
CPU revision is: 0001954c
Determined physical RAM map:
User-defined physical RAM map:
memory: 00f00000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 3810
Kernel command line: cramfs=0   slram=mainfs,0x00225000,+983040 console=ttyS1,115200 mtdparts=ifx_nand:4M(rgloader),0x02400000(UBI),-(JFFS2);ifx_sflash:-(sflash)   mem=0x00f00000 vpe1_load_addr=0x80f00000 vpe1_mem=0x00100000
1 MIPSR2 register sets available
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH
PID hash table entries: 64 (order: 6, 256 bytes)
Using 166.667 MHz high precision timer.
GPIO configuration for module 4 was not found.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 11412k/15360k available (1763k kernel code, 3948k reserved, 276k data, 148k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Lantiq PCI host controller driver, version 1.1.5, (c) 2001-2010 Lantiq Deutschland GmbH
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
IFX DMA driver, version ifxmips_dma_core.c:v1.0.7
,(c)2009 Infineon Technologies AG
Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH
Wired TLB entries for Linux read_c0_wired() = 0
/proc/fs/cramfs_block_uncompressed created
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
loop: loaded (max 8 devices)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 21
GPIO configuration for module 3 was found.
Lantiq SSC driver, version 2.1.5, (c) 2001-2010 Lantiq Deutschland GmbH
GPIO configuration for module 4 was not found.
ttyS0 at MMIO map 0xbe100400 mem 0xbe100400 (irq = 98) is a IFX_ASC
ttyS1 at MMIO map 0xbe100c00 mem 0xbe100c00 (irq = 105) is a IFX_ASC
Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH
Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH
ifx_nand_init
Probe for NAND flash...
NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
3 cmdlinepart partitions found on MTD device ifx_nand
Creating 3 MTD partitions on "ifx_nand":
0x00000000-0x00400000 : "rgloader"
0x00400000-0x02800000 : "UBI"
0x02800000-0x04000000 : "JFFS2"
PMCU initiates!
ifx_pmu_init: Major 253
Lantiq PMU driver, version 1.0.6, (c) 2001-2010 Lantiq Deutschland GmbH
/home/albert/trees/netia/Netia-5_4_8_2_23_1_2/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16
GPIO configuration for module 20 was found.
1 cmdlinepart partitions found on MTD device ifx_sflash
Creating 1 MTD partitions on "ifx_sflash":
0x00000000-0x00080000 : "sflash"
Lantiq SPI flash driver, version 1.1.8, (c) 2001-2010 Lantiq Deutschland GmbH
Freeing unused kernel memory: 148k freed
Found device mainfs on mtdblock0
Version: 5.4.8.2.23.1.2

Platform: Vtech ARX168 based Board

Compilation Time: 29-Mar-11 06:58:58

Tag: Ntag-5_4_8_2_23_1_2

Compilation Flags: DIST=RGLOADER_VTECH_ARX168_NETIA

User Information: albert@actaeon /home/albert/trees/netia/Netia-5_4_8_2_23_1_2


insmod: add-symbol-file build/debug/kos_lib.o 0xc0011000 -s .data 0xc0017e10 -s .bss 0xc0018c40
kos_lib: module license 'unspecified' taints kernel.
loading license key: jungo_rnd
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size:   16384 bytes (16 KiB)
UBI: logical eraseblock size:    15872 bytes
UBI: smallest flash I/O unit:    512
UBI: sub-page size:              256
UBI: VID header offset:          256 (aligned 256)
UBI: data offset:                512
UBI: attached mtd2 to ubi0
UBI: MTD device name:            "UBI"
UBI: MTD device size:            36 MiB
UBI: number of good PEBs:        2304
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       92
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             46
UBI: total number of reserved PEBs: 2258
UBI: number of PEBs reserved for bad PEB handling: 46
UBI: max/mean erase counter: 32/20
UBI: image sequence number: 22193626
UBI: background thread "ubi_bgt0d" started, PID 16
Press ESC to enter BOOT MENU mode.
Can't load valid rg_conf - using defaults
MAPS:

insmod: add-symbol-file build/debug/krgldr_module.o 0xc001b000 -s .data 0xc001b310 -s .bss 0xc001b4a0

insmod: add-symbol-file build/debug/ifxmips_3port_eth_sw_mod.o 0xc0024000 -s .data 0xc0026860 -s .bss 0xc00269c0
External Switch ID :0x00002599
GPIO configuration for module 25 was not found.
IFX 3 Port Switch Eth driver, version ifxmips_3port_sw.c:v1.0.4
,(c)2009 Infineon Technologies AG
RGLoader 5.4.8.2.23.1.2
Booting an active image in 1 seconds


Booting image from 0x1000000(0x81000000)...


Uncompressing Linux...

malloc: 00003E6C

returned: 81719014

..............................................................................................................................

Done

CramFS in 'NETIASPOT' mtd device. Image offset:00000000

Running from : (0x80002000) CramFS will be at: 0x001C5000

Booting the kernel

dcache writeback, cachesize 00004000 linesize 00000020

icache invalidate, cachesize 00008000 linesize 00000020

Infineon xDSL CPE AR9
mips_hpt_frequency = 166666666, counter_resolution = 2
Linux version 2.6.21.5 #1 Mon Jun 11 18:55:45 IDT 2012
rofs_addr: 001c5000 (801c5000), len: 550000, flash_start_addr: 00000000 (80000000) flash_len: 0
CramFS in Flash
rofs_start_addr: 00000000 len: 0
phym = 02000000, mem = 01f00000, max_pfn = 00001f00
Reserving memory for CP1 @0xa1f00000, size 0x00100000
CPU revision is: 0001954c
Determined physical RAM map:
User-defined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
Reserved 256k KLOG memory starting from Physical 0x01ec0000
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 7874
Kernel command line: cramfs=1 cramfs_offset=001c5000  mtdparts=ifx_nand:4M(rgloader),0x02400000(UBI),-(JFFS2);ifx_sflash:-(sflash);NETIASPOT:0x550000@0x001c5000(mainfs)  console=ttyS1,115200  mem=0x01f00000 vpe1_load_addr=0x81f00000 vpe1_mem=0x00100000
1 MIPSR2 register sets available
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH
PID hash table entries: 128 (order: 7, 512 bytes)
Using 166.667 MHz high precision timer.
GPIO configuration for module 4 was not found.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26468k/31744k available (2628k kernel code, 5276k reserved, 474k data, 164k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Lantiq PCI host controller driver, version 1.1.5, (c) 2001-2010 Lantiq Deutschland GmbH
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
Registered CRAMFS in UBI MTD notifier
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
IFX DMA driver, version ifxmips_dma_core.c:v1.0.7
,(c)2009 Infineon Technologies AG
Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH
Wired TLB entries for Linux read_c0_wired() = 0
/proc/fs/cramfs_block_uncompressed created
fuse init (API version 7.8)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
loop: loaded (max 8 devices)
slram: not enough parameters.
usbcore: registered new interface driver usblp
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial Driver core
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
u32 classifier
    OLD policer on
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 21
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GPIO configuration for module 3 was found.
Lantiq SSC driver, version 2.1.5, (c) 2001-2010 Lantiq Deutschland GmbH
IFX PPA API Directpath API loaded
GPIO configuration for module 4 was not found.
ttyS0 at MMIO map 0xbe100400 mem 0xbe100400 (irq = 98) is a IFX_ASC
ttyS1 at MMIO map 0xbe100c00 mem 0xbe100c00 (irq = 105) is a IFX_ASC
Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH
Infineon Technologies DEU driver version 1.0.1
IFX DEU DES initialized (multiblock).
IFX DEU AES initialized (multiblock).
IFX DEU ARC4 initialized (multiblock).
IFX DEU SHA1 initialized.
IFX DEU MD5 initialized.
IFX DEU SHA1_HMAC initialized.
IFX DEU MD5_HMAC initialized.
Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH
IFX MEI Version 5.00.04ifx_nand_init
Probe for NAND flash...
NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
3 cmdlinepart partitions found on MTD device ifx_nand
Creating 3 MTD partitions on "ifx_nand":
0x00000000-0x00400000 : "rgloader"
0x00400000-0x02800000 : "UBI"
0x02800000-0x04000000 : "JFFS2"
PMCU initiates!
ifx_pmu_init: Major 253
Lantiq PMU driver, version 1.0.6, (c) 2001-2010 Lantiq Deutschland GmbH
Loading A5 (MII0/1 + ATM) driver ...... <3>/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_gpio.c:828:ifx_gpio_pin_reserve: Pin ID 32 (port 2, pin 0) has been reserved by module PPA from kernel!
GPIO configuration for module 25 was not found.
Succeeded!
PPE datapath driver info:
  Version ID: 32.3.7.0.0.0.4
  Family    : AR9
  DR Type   : Normal Data Path | Indirect-Fast Path
  Interface : MII0 | MII1 | ATM
  Mode      : N/A
  Release   : 0.0.4
PPE firmware info:
  Version ID: 5.2.4.6.1.1
  Family    : AR9
  FW Type   : Acceleration
  Interface : MII0/1 + ATM
  Mode      : Bridging + IPv4 Routing
  Release   : 1.1
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16
GPIO configuration for module 20 was found.
1 cmdlinepart partitions found on MTD device ifx_sflash
Creating 1 MTD partitions on "ifx_sflash":
0x00000000-0x00080000 : "sflash"
Lantiq SPI flash driver, version 1.1.8, (c) 2001-2010 Lantiq Deutschland GmbH
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   16384 bytes (16 KiB)
UBI: logical eraseblock size:    15872 bytes
UBI: smallest flash I/O unit:    512
UBI: sub-page size:              256
UBI: VID header offset:          256 (aligned 256)
UBI: data offset:                512
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "UBI"
UBI: MTD device size:            36 MiB
UBI: number of good PEBs:        2304
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       92
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             46
UBI: total number of reserved PEBs: 2258
UBI: number of PEBs reserved for bad PEB handling: 46
UBI: max/mean erase counter: 32/20
UBI: image sequence number: 22193626
1 cmdlinepart partitions found on MTD device NETIASPOT
Creating 1 MTD partitions on "NETIASPOT":
0x001c5000-0x00715000 : "mainfs"
mtd: partition "mainfs" doesn't start on an erase block boundary -- force read-only
UBI: background thread "ubi_bgt0d" started, PID 15
Freeing unused kernel memory: 164k freed
Found device mainfs on mtdblock5
Version: 5.4.8.2.45.1.11

Platform: Vtech ARX168 based Board

Compilation Time: 11-Jun-12 15:30:39

Tag: Ntag-5_4_8_2_45_1_11

Compilation Flags: LIC=/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/20120611_1338/conf/jpkg_mipseb_netia_arx.lic CONFIG_RG_PROD_IMG=y DIST=VTECH_ARX168_NETIA

User Information: bat@rowlf /home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist


insmod: add-symbol-file build/debug/rg_klog.o 0xc0012000 -s .data 0xc0012300 -s .bss 0xc00124a0
klog loaded

insmod: add-symbol-file build/debug/rg_klog_ram_be.o 0xc000f000 -s .data 0xc0010880 -s .bss 0xc0010a20
klog: Using RAM buffer at address 0xa1ec0000 size 0x3fc00
klog: Invalid magic or checksum, reseting all information.
Linux version 2.6.21.5 #1 Mon Jun 11 18:55:45 IDT 2012
rofs_addr: 001c5000 (801c5000), len: 550000, flash_start_addr: 00000000 (80000000) flash_len: 0
CramFS in Flash
rofs_start_addr: 00000000 len: 0
phym = 02000000, mem = 01f00000, max_pfn = 00001f00
Reserving memory for CP1 @0xa1f00000, size 0x00100000
CPU revision is: 0001954c
Determined physical RAM map:
User-defined physical RAM map:
memory: 01f00000 @ 00000000 (usable)
Reserved 256k KLOG memory starting from Physical 0x01ec0000
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 7874
Kernel command line: cramfs=1 cramfs_offset=001c5000  mtdparts=ifx_nand:4M(rgloader),0x02400000(UBI),-(JFFS2);ifx_sflash:-(sflash);NETIASPOT:0x550000@0x001c5000(mainfs)  console=ttyS1,115200  mem=0x01f00000 vpe1_load_addr=0x81f00000 vpe1_mem=0x00100000
1 MIPSR2 register sets available
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
Lantiq ICU driver, version 3.0.1, (c) 2001-2010 Lantiq Deutschland GmbH
PID hash table entries: 128 (order: 7, 512 bytes)
Using 166.667 MHz high precision timer.
GPIO configuration for module 4 was not found.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26468k/31744k available (2628k kernel code, 5276k reserved, 474k data, 164k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Lantiq PCI host controller driver, version 1.1.5, (c) 2001-2010 Lantiq Deutschland GmbH
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
Registered CRAMFS in UBI MTD notifier
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
IFX DMA driver, version ifxmips_dma_core.c:v1.0.7
,(c)2009 Infineon Technologies AG
Lantiq CGU driver, version 1.0.9, (c) 2001-2010 Lantiq Deutschland GmbH
Wired TLB entries for Linux read_c0_wired() = 0
/proc/fs/cramfs_block_uncompressed created
fuse init (API version 7.8)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
loop: loaded (max 8 devices)
slram: not enough parameters.
usbcore: registered new interface driver usblp
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial Driver core
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/os/linux-2.6/drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.2
u32 classifier
    OLD policer on
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 21
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GPIO configuration for module 3 was found.
Lantiq SSC driver, version 2.1.5, (c) 2001-2010 Lantiq Deutschland GmbH
IFX PPA API Directpath API loaded
GPIO configuration for module 4 was not found.
ttyS0 at MMIO map 0xbe100400 mem 0xbe100400 (irq = 98) is a IFX_ASC
ttyS1 at MMIO map 0xbe100c00 mem 0xbe100c00 (irq = 105) is a IFX_ASC
Lantiq ASC (UART) driver, version 1.0.5, (c) 2001-2010 Lantiq Deutschland GmbH
Infineon Technologies DEU driver version 1.0.1
IFX DEU DES initialized (multiblock).
IFX DEU AES initialized (multiblock).
IFX DEU ARC4 initialized (multiblock).
IFX DEU SHA1 initialized.
IFX DEU MD5 initialized.
IFX DEU SHA1_HMAC initialized.
IFX DEU MD5_HMAC initialized.
Lantiq GPIO driver, version 1.2.12, (c) 2001-2010 Lantiq Deutschland GmbH
IFX MEI Version 5.00.04ifx_nand_init
Probe for NAND flash...
NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
3 cmdlinepart partitions found on MTD device ifx_nand
Creating 3 MTD partitions on "ifx_nand":
0x00000000-0x00400000 : "rgloader"
0x00400000-0x02800000 : "UBI"
0x02800000-0x04000000 : "JFFS2"
PMCU initiates!
ifx_pmu_init: Major 253
Lantiq PMU driver, version 1.0.6, (c) 2001-2010 Lantiq Deutschland GmbH
Loading A5 (MII0/1 + ATM) driver ...... <3>/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_gpio.c:828:ifx_gpio_pin_reserve: Pin ID 32 (port 2, pin 0) has been reserved by module PPA from kernel!
GPIO configuration for module 25 was not found.
Succeeded!
PPE datapath driver info:
  Version ID: 32.3.7.0.0.0.4
  Family    : AR9
  DR Type   : Normal Data Path | Indirect-Fast Path
  Interface : MII0 | MII1 | ATM
  Mode      : N/A
  Release   : 0.0.4
PPE firmware info:
  Version ID: 5.2.4.6.1.1
  Family    : AR9
  FW Type   : Acceleration
  Interface : MII0/1 + ATM
  Mode      : Bridging + IPv4 Routing
  Release   : 1.1
/home/bat/bat/vtech_netia_supp_5_4_8_2_45_1/dist/vendor/lantiq/xway/linux-2.6/drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16
GPIO configuration for module 20 was found.
1 cmdlinepart partitions found on MTD device ifx_sflash
Creating 1 MTD partitions on "ifx_sflash":
0x00000000-0x00080000 : "sflash"
Lantiq SPI flash driver, version 1.1.8, (c) 2001-2010 Lantiq Deutschland GmbH
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:   16384 bytes (16 KiB)
UBI: logical eraseblock size:    15872 bytes
UBI: smallest flash I/O unit:    512
UBI: sub-page size:              256
UBI: VID header offset:          256 (aligned 256)
UBI: data offset:                512
UBI: attached mtd1 to ubi0
UBI: MTD device name:            "UBI"
UBI: MTD device size:            36 MiB
UBI: number of good PEBs:        2304
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       92
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             46
UBI: total number of reserved PEBs: 2258
UBI: number of PEBs reserved for bad PEB handling: 46
UBI: max/mean erase counter: 32/20
UBI: image sequence number: 22193626
1 cmdlinepart partitions found on MTD device NETIASPOT
Creating 1 MTD partitions on "NETIASPOT":
0x001c5000-0x00715000 : "mainfs"
mtd: partition "mainfs" doesn't start on an erase block boundary -- force read-only
UBI: background thread "ubi_bgt0d" started, PID 15
Freeing unused kernel memory: 164k freed
Found device mainfs on mtdblock5
Algorithmics/MIPS FPU Emulator v1.5

insmod: add-symbol-file build/debug/rg_klog.o 0xc0012000 -s .data 0xc0012300 -s .bss 0xc00124a0
klog loaded

insmod: add-symbol-file build/debug/rg_klog_ram_be.o 0xc000f000 -s .data 0xc0010880 -s .bss 0xc0010a20
klog: Using RAM buffer at address 0xa1ec0000 size 0x3fc00
klog: Invalid magic or checksum, reseting all information.
klog initialization succeeded
klog RAM store initialization succeeded.

insmod: add-symbol-file build/debug/be_pppoa_mod.o 0xc0017000 -s .data 0xc0017cd0 -s .bss 0xc0017e40

insmod: add-symbol-file build/debug/be_pppos_mod.o 0xc0014000 -s .data 0xc0015b70 -s .bss 0xc0015d40

insmod: add-symbol-file build/debug/one_module.o 0xc00a6000 -s .main_flow 0xc00e8150 -s .data 0xc00f65a0 -s .bss 0xc00f8740
Loading license 12756d10c06ed9596404655b9295885c58b586796110f5772709751af73b96dd4363148a1e545bc0c793ad2a71ab865348b091bddb0490a7dac3cae35cac233c97bc9411a9dbdeef797d980542cc480921de41b32a03c8e3a9d9c6d410afa0c584c54b5683b748655958.ARX168_FOR_NETIA
loading license key: ARX168_FOR_NETIA
loading license key: ARX168_FOR_NETIA

insmod: add-symbol-file build/debug/jffs2.o 0xc0042000 -s .data 0xc005cb30 -s .bss 0xc005ccc0
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.

insmod: add-symbol-file build/debug/igmp_proxy_mod.o 0xc0020000 -s .data 0xc0022a40 -s .bss 0xc0022be0

insmod: add-symbol-file build/debug/kleds_mod.o 0xc001c000 -s .data 0xc001c910 -s .bss 0xc001cac0

insmod: add-symbol-file build/debug/wave300.o 0xc0222000 -s .data 0xc02b1360 -s .bss 0xc02b2260
[4294676706] mtlk0 (mtlk_cdev_init:265): Max nodex set to 1048575
[4294676706] mtlk0 (mtlk_fast_mem_print_info:103): Using normal memory for hot context
[4294676716] mtlk0(mtlk_vap_manager_create_vap:186): available vap_index 0
[4294677176] mtlk0(mtlk_core_start:7825): Driver version: 3.2.0.0.43.PciG3.Release
MAC/PHY versions:
ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r5644 MIPS: Upper CPU(TMC AGG AP) interface: PCI  phy type: real phy on May 17 2012 at 16:38:00@@@ END @@@
contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r5644 MIPS: Lower MAC  interface: --  phy type: real phy on May 17 2012 at 16:37:57@@@ END @@@

[4294678286] mtlk0(mtlk_eeprom_check_ee_data:2074): Options mask is 0x00
[4294678286] mtlk0(load_default_hw_table:1805): HW configuration is 2X2
[4294678296] mtlk0(mtlk_df_user_start:5577): NDEV Name pattern: wlan%d
Press ESC to enter BOOT MENU mode.
MAPS:
00400000-00775000 r-xp 00000000 1f:05 737128     /mnt/cramfs/bin/openrg
007b4000-0083e000 rw-p 00374000 1f:05 737128     /mnt/cramfs/bin/openrg
0083e000-00
insmod: add-symbol-file build/debug/rg_klog_chardev.o 0xc001e000 -s .data 0xc001e3a0 -s .bss 0xc001e540
a0f000 klog chardev initialized.
rwxp 0083e000 00:00 0          [heap]
2aaa8000-2aaae000 r-xp 00000000 1f:05 4470908    /mnt/cramf
insmod: add-symbol-file build/debug/log_chardev.o 0xc0025000 -s .data 0xc0025730 -s .bss 0xc00258c0
s/lib/ld-uClibc.so.0
2aaae000-2aaaf000 rw-p 2aaae000 00:00 0
2aaed000-2aaee000 r--p 00005000 1f:05 4470908    /mnt/cramfs/lib/ld-uClibc.so.0
2aaee000-2aaef000 rw-p 00006000 1f:05 44
insmod: add-symbol-file build/debug/rg_usfs.o 0xc0019000 -s .data 0xc0019ea0 -s .bss 0xc001a040
70908    /mnt/cramfs/lib/ld-uClibc.so.0
2aaef000-2ab00000 r-xp 00000000 1f:05 5189260    /mnt/cramfs/lib/libopenrg.so
2ab00000-2ab40000 ---p 2ab00000 00:00 0
2ab40000-2ab41000 rw-p 00011000 1f:05 518
insmod: add-symbol-file build/debug/tcp_mss.o 0xc002a000 -s .data 0xc002a590 -s .bss 0xc002a720
9260    /mnt/cramfs/lib/libopenrg.so
2ab41000-2ab87000 r-xp 00000000 1f:05 4975636    /mnt/cramfs/lib/libjutil.so
2a
insmod: add-symbol-file build/debug/rg_ipv4.o 0xc002c000 -s .data 0xc002c1f0 -s .bss 0xc002c380
b87000IPV4 device driver registered
-2abc6000 ---p 2ab87000 00:00 0
2abc6000-2abce000 rw-p 00045000 1f:05 4975636    /mnt/cramfs/lib/libjutil.so
2ab
insmod: add-symbol-file build/debug/btn.o 0xc002e000 -s .data 0xc002e820 -s .bss 0xc002e9c0
ce000-2abd4000 rw-p 2abce000 00:00 0
2abd4000-2ac0c000 r-xp 00000000 1f:05 5361528    /mGPIO configuration for module 29 was not found.
nt/cramfs/lib/libssl.so
2ac0c000-2ac4b000 ---p 2ac0c000 00:00 0
2ac4b000-2ac4f000 rw-p 00037000 1f:05 5361528    /mnt/
insmod: add-symbol-file build/debug/qos_ingress.o 0xc0030000 -s .data 0xc0030a60 -s .bss 0xc0030c00
cramfs/lib/libssl.so
2ac4f000-2ad49000 r-xp 00000000 1f:05 4623912    /mnt/cramfs/lib/libcrypto.so
2ad49000-2ad88000 ---p 2ad49000 00:00 0
2ad88000-2ad9b000 rw-p 000f9000 1f:05 4623912    /mnt/cramfs/lib/libcrypto.so
2ad9b000-2ad9e000 rw-p 2ad9b000 00:00 0
2ad9e000-2ada0000 r-xp 00000000 1f:05 4947008    /mnt/cramfs/lib/libdl.so.0
2ada0000-2addf000 ---p 2ada0000 00:00 0
2addf000-2ade0000 r--p 00001000 1f:05 4947008    /mnt/cramfs/lib/libdl.so.0
2ade0000-2ade1000 rw-p 00002000 1f:05 4947008    /mnt/cramfs/lib/libdl.so.0
2ade1000-2adf9000 r-xp 00000000 1f:05 5242816    /mnt/cramfs/lib/librg_config.so
2adf9000-2ae39000 ---p 2adf9000 00:00 0
2ae39000-2ae3c000 rw-p 00018000 1f:05 5242816    /mnt/cramfs/lib/librg_config.so
2ae3c000-2ae4b000 r-xp 00000000 1f:05 5070952    /mnt/cramfs/lib/libm.so.0
2ae4b000-2ae8b000 ---p 2ae4b000 00:00 0
2ae8b000-2ae8c000 rw-p 0000f000 1f:05 5070952    /mnt/cramfs/lib/libm.so.0
2ae8c000-2ae8d000 r-xp 00000000 1f:05 5483732    /mnt/cramfs/lib/libutil.so.0
2ae8d000-2aecd000 ---p 2ae8d000 00:00 0
2aecd000-2aece000 rw-p 00001000 1f:05 5483732    /mnt/cramfs/lib/libutil.so.0
2aece000-2af36000 r-xp 00000000 1f:05 4479912    /mnt/cramfs/lib/libc.so.0
2af36000-2af75000 ---p 2af36000 00:00 0
2af75000-2af76000 r--p 00067000 1f:05 4479912    /mnt/cramfs/li
insmod: add-symbol-file build/debug/ifxusb_driver_mod.o 0xc0081000 -s .data 0xc00940f0 -s .bss 0xc0094880
b/libc.so.0
2af76000-2af78000 rw-p 00068000 1f:05 4479912    /mnt/cramfs/lib/libc.so.0
2af78000-2af7IFXUSB: ifxusb_hcd: version 3.0 B101005
c000 rw-p 2af78000 00:00 0
7fd1e000-7fd33000 rwxp 7fd1e000 00:00 0          [stack]
IFXUSB: USB core #0 soft-reset
IFXUSB: USB core #0 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000
GPIO configuration for module 7 was found.
IFXUSB: Init: Power Port (0)
registering (overcurrent) handler for irq 158
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
IFXUSB: USB core #1 soft-reset
IFXUSB: USB core #1 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
ifxusb_hcd ifxusb_hcd: irq 83, io mem 0xbe106000
IFXUSB: Init: Power Port (0)
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected

insmod: add-symbol-file build/debug/drv_dsl_cpe_api_mod.o 0xc0192000 -s .data 0xc01cd6d0 -s .bss 0xc01ce4e0


Lantiq CPE API Driver version: DSL CPE API V4.2.0

Predefined debug level: 3

insmod: add-symbol-file build/debug/psb6973_mod.o 0xc0037000 -s .data 0xc0038ff0 -s .bss 0xc0039280
Freeing CRAMFS/MODFS: 768k freed
userspace registering PID
[4294693066] mtlk0(_mtlk_core_mbss_add_vap:5357): Got PRM_ID_VAP_ADD
[4294693076] mtlk0(mtlk_vap_manager_create_vap:186): available vap_index 1
[4294693076] mtlk0(mtlk_core_start:7825): Driver version: 3.2.0.0.43.PciG3.Release
MAC/PHY versions:
ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r5644 MIPS: Upper CPU(TMC AGG AP) interface: PCI  phy type: real phy on May 17 2012 at 16:38:00@@@ END @@@
contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r5644 MIPS: Lower MAC  interface: --  phy type: real phy on May 17 2012 at 16:37:57@@@ END @@@

[4294693086] mtlk0(mtlk_df_user_start:5577): NDEV Name pattern: wlan0.%d
[4294693086] mtlk0(_mtlk_core_mbss_add_vap:5368): VAP#1 added
[4294693106] mtlk0(_mtlk_core_mbss_add_vap:5357): Got PRM_ID_VAP_ADD
[4294693116] mtlk0(mtlk_vap_manager_create_vap:186): available vap_index 2
[4294693116] mtlk0(mtlk_core_start:7825): Driver version: 3.2.0.0.43.PciG3.Release
MAC/PHY versions:
ap_upper.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r5644 MIPS: Upper CPU(TMC AGG AP) interface: PCI  phy type: real phy on May 17 2012 at 16:38:00@@@ END @@@
contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.2.0_r5644 MIPS: Lower MAC  interface: --  phy type: real phy on May 17 2012 at 16:37:57@@@ END @@@

[4294693126] mtlk0(mtlk_df_user_start:5577): NDEV Name pattern: wlan0.%d
[4294693126] mtlk0(_mtlk_core_mbss_add_vap:5368): VAP#2 added
Modem is not ready!eth0_main: MAC Address: 00:12:2A:xx:xx:xx
device eth0_main entered promiscuous mode
eth2: MAC Address: 00:12:2A:xx:xx:xx
[4294694756] mtlk0(_mtlk_mbss_send_preactivate:2198): bonding = 0
[4294694766] mtlk0(_mtlk_mbss_send_preactivate:2204): mtlk_aocs_set_spectrum_mode with 0
[4294694776] mtlk0(_mtlk_mbss_send_preactivate:2209): mtlk_aocs_set_config_is_ht with 1
[4294694776] mtlk0(_mtlk_mbss_send_preactivate:2212): mtlk_aocs_set_config_frequency_band with 1
[4294694786] mtlk0(_mtlk_mbss_send_preactivate:2217): mtlk_aocs_start
[4294694796] mtlk0(_mtlk_mbss_send_preactivate:2229): ap_scan_band_cfg = 1
[4294694806] mtlk0(_mtlk_core_perform_initial_scan:2075): AOCS is ON (ch=0 type=0): doing the Initial Scan
[4294694816] mtlk0(_mtlk_core_perform_initial_scan:2086): Initial scan started SPECTRUM_20MHZ
[4294697536] mtlk0(_mtlk_mbss_send_preactivate:2317): mtlk_txmm_msg_send_blocked, MsgId = 0x451
[4294697726] mtlk0(_mtlk_mbss_send_preactivate:2336): _mtlk_mbss_send_preactivate returned successfully
[4294697736] mtlk0(mtlk_mbss_init:2688): _mtlk_mbss_send_preactivate_if_needed returned successfully
[4294697746] mtlk0(mtlk_mbss_send_vap_activate:2399): Entering mtlk_mbss_send_vap_activate
[4294697746] mtlk0(mtlk_mbss_send_vap_activate:2406): wlan0
[4294697756] mtlk0(mtlk_mbss_send_vap_activate:2454): UMI_ACTIVATE_VAP (wlan0)
[4294697766] mtlk0(mtlk_mbss_send_vap_activate:2455):     sBSSID = 00:12:2a:xx:xx:xx
[4294697766] mtlk0(mtlk_mbss_send_vap_activate:2456):     sSSID  = NETIASPOT-xxxxxx
[4294697776] mtlk0(mtlk_mbss_send_vap_activate:2457):     Hidden = 0
[4294697786] mtlk0 (mtlk_mbss_send_vap_activate:2458):     sRSNie =
cp= 0x804c093a l=80
0000:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
0010:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
0020:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
0030:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
0040:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
[4294697816] mtlk0(mtlk_mbss_send_vap_activate:2460): mtlk_txmm_msg_send, MsgId = 0x453, ESSID = NETIASPOT-xxxxxx
[4294697826] mtlk0(mtlk_mbss_init:2695): mtlk_mbss_send_vap_activate returned successfully
device wlan0 entered promiscuous mode
[4294706916] mtlk0(_mtlk_mbss_send_preactivate:2198): bonding = 0
[4294706926] mtlk0(_mtlk_mbss_send_preactivate:2204): mtlk_aocs_set_spectrum_mode with 0
[4294706936] mtlk0(_mtlk_mbss_send_preactivate:2209): mtlk_aocs_set_config_is_ht with 1
[4294706936] mtlk0(_mtlk_mbss_send_preactivate:2212): mtlk_aocs_set_config_frequency_band with 1
[4294706946] mtlk0(_mtlk_mbss_send_preactivate:2217): mtlk_aocs_start
[4294706956] mtlk0(_mtlk_mbss_send_preactivate:2229): ap_scan_band_cfg = 1
[4294706956] mtlk0(_mtlk_core_perform_initial_scan:2094): AOCS is completely OFF (ch=3 type=0): skipping the Initial Scan
[4294706966] mtlk0(_mtlk_mbss_send_preactivate:2317): mtlk_txmm_msg_send_blocked, MsgId = 0x451
Username: [4294707156] mtlk0(_mtlk_mbss_send_preactivate:2336): _mtlk_mbss_send_preactivate returned successfully
[4294707166] mtlk0(mtlk_mbss_init:2688): _mtlk_mbss_send_preactivate_if_needed returned successfully
[4294707176] mtlk0(mtlk_mbss_send_vap_activate:2399): Entering mtlk_mbss_send_vap_activate
[4294707176] mtlk0(mtlk_mbss_send_vap_activate:2406): wlan0
[4294707186] mtlk0(mtlk_mbss_send_vap_activate:2454): UMI_ACTIVATE_VAP (wlan0)
[4294707196] mtlk0(mtlk_mbss_send_vap_activate:2455):     sBSSID = 00:12:2a:xx:xx:xx
[4294707196] mtlk0(mtlk_mbss_send_vap_activate:2456):     sSSID  = NETIASPOT-xxxxxx
[4294707206] mtlk0(mtlk_mbss_send_vap_activate:2457):     Hidden = 0
[4294707216] mtlk0 (mtlk_mbss_send_vap_activate:2458):     sRSNie =
cp= 0x804c1d0e l=80
0000:  30 18 01 00 00 0f ac 02  02 00 00 0f ac 04 00 0f
0010:  ac 02 01 00 00 0f ac 02  00 00 dd 1a 00 50 f2 01
0020:  01 00 00 50 f2 02 02 00  00 50 f2 04 00 50 f2 02
0030:  01 00 00 50 f2 02 00 00  00 00 00 00 00 00 00 00
0040:  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00
[4294707246] mtlk0(mtlk_mbss_send_vap_activate:2460): mtlk_txmm_msg_send, MsgId = 0x453, ESSID = NETIASPOT-xxxxxx
[4294707256] mtlk0(mtlk_mbss_init:2695): mtlk_mbss_send_vap_activate returned successfully
openrg uses obsolete (PF_INET,SOCK_PACKET)
DSL[00]: Reboot on training timeout (120)!!!
DSL[00]: Reboot on training timeout (120)!!!
DSL[00: ERROR - PM module is temporary locked!
lantiq_ar9_dsl_ioctl:67: Failed ioctl -1071878131 errno 14 status -1
dev_if_lantiq_ar9_dsl_ioctl:619: Could not determine dsl connect status
DSL[00]: Reboot on training timeout (120)!!!


Password:

I zapłoną piekielnym ogniem wasze serwery, gdyż zabezpieczenia ich wątłe, a podatnośc na buffer overflowy ogromna. I zaprzestaną działania wasze routery a wasze niewiasty nosić będą pakiety w kubłach, a tam będzie płacz, zgrzytanie zębów, 404 i request timeout.

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

Więc stawiaj lantiq i zobacz czy się w ogóle uruchamia.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez filos51

  • Skąd: Warszawa
  • Zarejestrowany: 2011-10-22
  • Posty: 10

Odp: Openwrt dla netiaspot

Witam

Czyli wziąć któryś z gotowych obrazów na platformę lantiq i spróbować wrzucić go przez tftp korzystając z opcji  u-boota?

Mając podgląd przez rs (putty) powinienem zobaczyć czy cokolwiek się uruchomi smile chyba.

Obawiam się że moje umiejętności w tym temacie mogą być lekko niewystarczające.

Pozdrawiam.

I zapłoną piekielnym ogniem wasze serwery, gdyż zabezpieczenia ich wątłe, a podatnośc na buffer overflowy ogromna. I zaprzestaną działania wasze routery a wasze niewiasty nosić będą pakiety w kubłach, a tam będzie płacz, zgrzytanie zębów, 404 i request timeout.

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

Tak, po prostu sprawdź czy któryś się uruchomi czy nie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez filos51 (edytowany przez filos51 2012-12-28 18:31:21)

  • Skąd: Warszawa
  • Zarejestrowany: 2011-10-22
  • Posty: 10

Odp: Openwrt dla netiaspot

Witam

Coś nie mogę sobie poradzić z opcjami uboota:

?            - alias for 'help'
askenv   - get environment variables from stdin
base      - print or set address offset
bootm    - boot application image from memory
bootp     - boot image via network using BootP/TFTP protocol
cmp        - memory compare
cp           - memory copy
crc32      - checksum calculation
echo       - echo args to console
go           - start application at address 'addr'
help        - print online help
imls    - list all images found in flash
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sf      - SPI flash sub-system
tftpboot- boot image via network using TFTP protocol
upgrade - forward/backward copy memory to pre-defined flash location
version - print monitor version

a to po użyciu printenv

AMAZON_S # printenv
bootcmd=run boot_flash
bootdelay=1
baudrate=115200
preboot=echo;echo Type "run flash_nfs" to mount root filesystem over NFS;echo
bootfile=uImage
mem=31M
phym=32M
ipaddr=192.168.1.1
serverip=192.168.1.10
ethaddr=00:E0:92:00:01:40
netdev=eth0
console=ttyS1
baudrate=115200
tftppath=
loadaddr=0x80800000
rootpath=/mnt/full_fs
rootfsmtd=/dev/mtdblock2
nfsargs= setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath)
ramargs=setenv bootargs root=/dev/ram rw
addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):on
addmisc=setenv bootargs $(bootargs) console=$(console),$(baudrate) ethaddr=$(ethaddr) phym=$(phym) mem=$(mem) panic=1 mtdparts=$(mtdparts) init=/etc/preinit quiet vpe1_load_addr=0x81f00000 vpe1_mem=1M ethwan=$(ethwan)
flash_nfs=run nfsargs addip addmisc;bootm $(kernel_addr)
net_nfs=tftp $(loadaddr) $(tftppath)$(bootfile);run nfsargs addip addmisc;bootm
net_flash=tftp $(loadaddr) $(tftppath)$(bootfile); run flashargs addip addmisc; bootm
net_ram=tftp $(loadaddr) $(tftppath)$(bootfile); run ramargs addip addmisc; bootm
u-boot=u-boot.sflash
rootfs=rootfs.img
firmware=firmware.img
fullimage=fullimage.img
totalimage=totalimage.img
load=tftp $(loadaddr) $(u-boot)
update=protect off 1:0-2;era 1:0-2;cp.b $(loadaddr) B0000000 $(filesize)
flashargs=setenv bootargs root=$(rootfsmtd) ro rootfstype=squashfs
flash_flash=sf probe 3; sf read 80500000 $(f_kernel_addr) $(f_kernel_size);run flashargs addip addmisc; bootm 80500000
update_uboot=tftpboot $(loadaddr) $(tftppath)$(u-boot);sf probe 3; sf erase 0 20000; sf write $(loadaddr) 0 $(filesize); reset
update_kernel=tftpboot $(loadaddr) $(tftppath)$(bootfile);upgrade $(loadaddr) $(filesize)
update_rootfs=tftpboot $(loadaddr) $(tftppath)$(rootfs); upgrade $(loadaddr) $(filesize)
update_firmware=tftpboot $(loadaddr) $(tftppath)$(firmware);upgrade $(loadaddr) $(filesize)
update_fullimage=tftpboot $(loadaddr) $(tftppath)$(fullimage);upgrade $(loadaddr) $(filesize)
update_totalimage=tftpboot $(loadaddr) $(tftppath)$(totalimage);upgrade $(loadaddr) $(filesize)
reset_ddr_config=sf probe 3; mw.b 80000000 0 4; sf write 80000000 0x00004FE8 4
mtdparts=ifx_sflash:64k(uboot),256k(firmware),-(rootfs)
reset_uboot_config=sf probe 3;   sf erase 0x0007F000 0x00001000
flash_end=0x0007FFFF
f_uboot_addr=IFX_CFG_FLASH_UBOOT_IMAGE_START_ADDR
f_uboot_size=IFX_CFG_FLASH_UBOOT_IMAGE_SIZE
f_ubootconfig_addr=0x0007F000
f_ubootconfig_size=0x00001000
f_ubootconfig_end=0x0007FFFF
f_kernel_addr=IFX_CFG_FLASH_KERNEL_IMAGE_START_ADDR
f_kernel_size=IFX_CFG_FLASH_KERNEL_IMAGE_SIZE
f_kernel_end=IFX_CFG_FLASH_KERNEL_IMAGE_END_ADDR
f_rootfs_addr=IFX_CFG_FLASH_ROOTFS_IMAGE_START_ADDR
f_rootfs_size=IFX_CFG_FLASH_ROOTFS_IMAGE_SIZE
f_rootfs_end=IFX_CFG_FLASH_ROOTFS_IMAGE_END_ADDR
f_firmware_addr=IFX_CFG_FLASH_FIRMWARE_IMAGE_START_ADDR
f_firmware_size=IFX_CFG_FLASH_FIRMWARE_IMAGE_SIZE
f_sysconfig_addr=IFX_CFG_FLASH_SYSTEM_CFG_START_ADDR
f_sysconfig_size=IFX_CFG_FLASH_SYSTEM_CFG_SIZE
f_fwdiag_addr=IFX_CFG_FLASH_FIRMWARE_DIAG_START_ADDR
f_fwdiag_size=IFX_CFG_FLASH_FIRMWARE_DIAG_SIZE
f_calibration_addr= IFX_CFG_FLASH_CALIBRATION_CFG_SIZE
f_calibration_size=IFX_CFG_FLASH_CALIBRATION_CFG_SIZE
f_ddrconfig_addr=0x00004FE8
f_ddrconfig_size=24
boot_net=tftpboot 81000000 openrg.img; go 81000000
boot_flash=nand read.e 80c00000 0 400000; go 80c00000
update_rgloader=tftpboot 80c00000 rgloader.img ; nand erase 0 400000; nand write.e 80c00000 0 400000
stdin=serial
stdout=serial
stderr=serial
ethact=amazon_s Switch

Environment size: 3516/4092 bytes

Wybrałem opcję tftpboot
Zmieniłem nazwę pliku na uImage,
karte sieciową na sztywno brama 192.168.1.1 a ip 192.168.1.10
jednak szuka w kółko pliku.

I zapłoną piekielnym ogniem wasze serwery, gdyż zabezpieczenia ich wątłe, a podatnośc na buffer overflowy ogromna. I zaprzestaną działania wasze routery a wasze niewiasty nosić będą pakiety w kubłach, a tam będzie płacz, zgrzytanie zębów, 404 i request timeout.

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

Raczej openrg.img

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

PS. - jeżeli to jest amazon-se to Netgear DGN1000B jest tą samą platformą, więc jak już to jego obrazu powinieneś użyć.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

8 Odpowiedź przez theboo

  • theboo
  • Użytkownik
  • Nieaktywny
  • Skąd: Warszawa
  • Zarejestrowany: 2013-01-05
  • Posty: 24

Odp: Openwrt dla netiaspot

Cezary napisał/a:

PS. - jeżeli to jest amazon-se to Netgear DGN1000B jest tą samą platformą, więc jak już to jego obrazu powinieneś użyć.

http://www.wikidevi.com/wiki/Netgear_DGN1000

Netia Spot bazuje na Lantiq ARX168
czyli na tym co np. to http://www.wikidevi.com/wiki/BT_Home_Hub_3.0A

<br />
<b>Deprecated</b>:  htmlspecialchars(): Passing null to parameter #1 ($string) of type string is deprecated in <b>/home/jackiewicz/domains/eko.one.pl/public_html/forum/include/functions.php</b> on line <b>17</b><br />

9 Odpowiedź przez bander

  • bander
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-05-31
  • Posty: 27

Odp: Openwrt dla netiaspot

NetiaSpot jest dosc speczyficznym sprzetem. Nie jest podobny do Netgear DGN1000 choc bootlader moglby na to wskazywac.

Chipset: PSB 50810 EL v 1.2 - XWAY ARX168
Radio: PSB 8221 EL v1.1 - XWAY WAVE300
LAN: PSB 6970 V  v1.3
Flash SPI : Macronix MX25L4006E (512kB)
Flash NAND: Toshiba NL3283
RAM: EtronTech EM6AA160TSA-5G (16M x 16bits - DDR - TSOP II 66 pins)

Router startuje pierwszy bootlader z kosci Flash SPI po czym laduje kolejny z kosci Flash NAND.

10 Odpowiedź przez filos51

  • Skąd: Warszawa
  • Zarejestrowany: 2011-10-22
  • Posty: 10

Odp: Openwrt dla netiaspot

Witam

Ja jak na razie poległem jeśli chodzi o openwrt na netiaspot.

Jeśli byłby ktoś chętny do podjęcia walki z w/w sprzętem jestem wstanie udostępnić swój egzemplarz.

Pozdrawiam.

I zapłoną piekielnym ogniem wasze serwery, gdyż zabezpieczenia ich wątłe, a podatnośc na buffer overflowy ogromna. I zaprzestaną działania wasze routery a wasze niewiasty nosić będą pakiety w kubłach, a tam będzie płacz, zgrzytanie zębów, 404 i request timeout.

11 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

A tu macie mój log z uruchomienia openwrt. Na DGN3500 nie patrzcie, bo ten profil przerabiałem.

[    0.000000] Linux version 3.7.5 (cezary@eko.one.pl) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Thu Jan 31 15:21:41 CET 2013
[    0.000000] SoC: AR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001954c (MIPS 34Kc)
[    0.000000] Board: DGN3500 - Netgear DGN3500
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line: mem=32M console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Writing ErrCtl register=0000b4d0
[    0.000000] Readback ErrCtl register=0000b4d0
[    0.000000] Memory: 26272k/32768k available (2535k kernel code, 6496k reserved, 780k data, 2628k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 333MHz
[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 512
[    0.048000] pinctrl core: initialized pinctrl subsystem
[    0.052000] NET: Registered protocol family 16
[    0.064000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.068000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20
[    0.080000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.084000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.088000]   IO 0x000000001ae00000..0x000000001affffff
[    0.108000] bio: create slab <bio-0> at 0
[    0.116000] usbcore: registered new interface driver usbfs
[    0.120000] usbcore: registered new interface driver hub
[    0.124000] usbcore: registered new device driver usb
[    0.128000] PCI host bridge to bus 0000:00
[    0.132000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.136000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.140000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.144000] pci 0000:00:0e.0: BAR 1: assigned [mem 0x18000000-0x187fffff pref]
[    0.148000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18800000-0x18800fff pref]
[    0.152000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
[    0.156000] Switching to clocksource MIPS
[    0.164000] NET: Registered protocol family 2
[    0.168000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.176000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.184000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.188000] TCP: reno registered
[    0.192000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.200000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.204000] NET: Registered protocol family 1
[    0.964000] gptu: totally 6 16-bit timers/counters
[    0.972000] gptu: misc_register on minor 63
[    0.976000] gptu: succeeded to request irq 126
[    0.980000] gptu: succeeded to request irq 127
[    0.984000] gptu: succeeded to request irq 128
[    0.988000] gptu: succeeded to request irq 129
[    0.992000] gptu: succeeded to request irq 130
[    0.996000] gptu: succeeded to request irq 131
[    1.008000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.016000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.024000] msgmni has been set to 51
[    1.028000] io scheduler noop registered
[    1.032000] io scheduler deadline registered (default)
[    1.040000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    1.048000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.048000] console [ttyLTQ0] enabled, bootconsole disabled
[    1.064000] spi_gpio spi.4: master is unqueued, this is deprecated
[    1.072000] m25p80 spi32766.0: unrecognized JEDEC id ffffff
[    1.076000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[    1.084000] rtl8366rb rtl8366rb.5: using GPIO pins 235 (SDA) and 237 (SCK)
[    1.088000] rtl8366rb rtl8366rb.5: unknown chip id (0000)
[    1.096000] rtl8366rb rtl8366rb.5: chip detection failed, err=-19
[    1.104000] etop: invalid MAC, using random
[    1.128000] libphy: ltq_mii: probed
[    1.132000] eth0: psb6970 switch driver attached.
[    1.136000] eth0: attached PHY [Lantiq PSB6970] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    1.148000] wdt 1f8803f0.watchdog: Init done
[    1.152000] leds-gpio gpio-leds.7: pins are not configured from the driver
[    1.164000] TCP: cubic registered
[    1.168000] NET: Registered protocol family 17
[    1.172000] 8021q: 802.1Q VLAN Support v1.8
[    1.192000] Freeing unused kernel memory: 2628k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. [    5.804000] Compat-drivers backport release: compat-drivers-2013-01-08-3
[    5.808000] Backport based on wireless-testing.git master-2013-01-07
[    5.816000] compat.git: wireless-testing.git
[    5.848000] cfg80211: Calling CRDA to update world regulatory domain
[    5.856000] cfg80211: World regulatory domain updated:
[    5.860000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    5.868000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    5.876000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    5.884000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    5.892000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    5.900000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.064000] NET: Registered protocol family 8
[    6.068000] NET: Registered protocol family 20
[    6.240000] PPP generic driver version 2.4.2
[    6.308000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    6.468000] NET: Registered protocol family 24
[    6.496000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
[    6.768000] IFX MEI Version 5.00.00
[    6.792000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[    7.296000] IFXUSB: USB core #0 soft-reset
[    7.500000] IFXUSB: USB core #0 soft-reset
[    7.504000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    7.508000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[    7.516000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[    7.520000] IFXUSB: Init: Power Port (0)
[    7.524000] hub 1-0:1.0: USB hub found
[    7.528000] hub 1-0:1.0: 1 port detected
[    7.556000] 
[    7.556000] 
[    7.556000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[    7.584000] ATM1.0.26    ATM (A1) firmware version 0.16
[    7.588000] ifxmips_atm: ATM init succeed
[    7.608000] Infineon Technologies DEU driver version 2.0.0 
[    7.612000] IFX DEU DES initialized (multiblock).
[    7.616000] IFX DEU AES initialized (multiblock).
[    7.620000] IFX DEU ARC4 initialized (multiblock).
[    7.624000] IFX DEU SHA1 initialized.
[    7.628000] IFX DEU MD5 initialized.
[    7.632000] IFX DEU SHA1_HMAC initialized.
[    7.636000] IFX DEU MD5_HMAC initialized.
[    7.656000] ltq_ptm_ar9: module license 'unspecified' taints kernel.
[    7.660000] Disabling lock debugging due to kernel taint
[    8.076000] genirq: Flags mismatch irq 96. 00000020 (ptm_mailbox_isr) vs. 00000020 (atm_mailbox_isr)
[    8.084000] /home/cezary/projekty/openwrt/lantiq-trunk/build_dir/target-mips_r2_uClibc-0.9.33.2/linux-lantiq_xway/ltq-ptm-ar9/ifxmips_ptm_adsl.c:1461:ifx_ptm_init: IRQ may be occupied by other driver, please reconfig to disable it.
[    8.104000] ifxmips_ptm: PTM init failed
[   13.008000] device eth0 entered promiscuous mode
[   13.016000] br-lan: port 1(eth0) entered forwarding state
[   13.020000] br-lan: port 1(eth0) entered forwarding state
[   15.024000] br-lan: port 1(eth0) entered forwarding state



BusyBox v1.19.4 (2013-01-29 18:41:58 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r35412)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/# cat /proc/cpuinfo 
system type        : AR9 rev 1.2 - DGN3500 - Netgear DGN3500
processor        : 0
cpu model        : MIPS 34Kc V4.12
BogoMIPS        : 221.18
wait instruction    : yes
microsecond timers    : yes
tlb_entries        : 16
extra interrupt vector    : yes
hardware watchpoint    : yes, count: 4, address/irw mask: [0x0ff8, 0x0ffc, 0x0ffb, 0x0ff8]
ASEs implemented    : mips16 dsp mt
shadow register sets    : 1
kscratch registers    : 0
core            : 0
VCED exceptions        : not available
VCEI exceptions        : not available

root@OpenWrt:/# 
root@OpenWrt:/# ifconfig 
br-lan    Link encap:Ethernet  HWaddr F6:07:6B:77:58:8A  
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:278 (278.0 B)  TX bytes:402 (402.0 B)

eth0      Link encap:Ethernet  HWaddr F6:07:6B:77:58:8A  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:503 (503.0 B)  TX bytes:402 (402.0 B)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:528 errors:0 dropped:0 overruns:0 frame:0
          TX packets:528 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:35904 (35.0 KiB)  TX bytes:35904 (35.0 KiB)

nas0      Link encap:Ethernet  HWaddr 00:00:01:00:00:00  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13 errors:13 dropped:0 overruns:13 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:546 (546.0 B)

root@OpenWrt:/# ping 192.168.1.166
PING 192.168.1.166 (192.168.1.166): 56 data bytes
64 bytes from 192.168.1.166: seq=0 ttl=64 time=0.864 ms
^C
--- 192.168.1.166 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 0.864/0.864/0.864 ms
root@OpenWrt:/# 
root@OpenWrt:/# [  184.220000] usb 1-1: new high-speed USB device number 2 using ifxusb_hcd

uruchomione z ramdysku.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

12 Odpowiedź przez theboo

  • theboo
  • Użytkownik
  • Nieaktywny
  • Skąd: Warszawa
  • Zarejestrowany: 2013-01-05
  • Posty: 24

Odp: Openwrt dla netiaspot

jak na ramdysku działa to znaczy że po wrzuceniu na flash też będzie działał? czy to nie jest takie proste...? wink

<br />
<b>Deprecated</b>:  htmlspecialchars(): Passing null to parameter #1 ($string) of type string is deprecated in <b>/home/jackiewicz/domains/eko.one.pl/public_html/forum/include/functions.php</b> on line <b>17</b><br />

13 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

To znaczy żeby działało poprawnie ktoś musi napisać "mapę" urządzenia opisującą wszystkie jego elementy sprzętowe.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

14 Odpowiedź przez ScApi

  • ScApi
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2010-08-16
  • Posty: 5

Odp: Openwrt dla netiaspot

Odświeżę trochę temat, mianowicie mapa urządzenia już jest, przeportowany hostapd również, mam tylko problem z portem sterowników WiFI, coraz więcej urządzeń na Wave300 pojawia się na rynku, niestety na forum openwrt nie wzbudza to specjalnego zainteresowania.

Sam poległem przy próbie kompilacji sterowników pod aktualny kernel/toolchain stąd prośba czy ktoś mógłby rzucić okiem i pokierować na właściwy tor, bazowałem na makefile atherosa ale niestety nic z tego nie wyszło.

W linku sterownik ze źródeł TP-Link'a
https://www.dropbox.com/s/0tg0krp4rwt8e … src.tar.gz

15 Odpowiedź przez lpm11

  • lpm11
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2010-11-10
  • Posty: 6

Odp: Openwrt dla netiaspot

Już udało się uruchomić sterownik na jądrze 3.3.8, AA

16 Odpowiedź przez lpm11 (edytowany przez lpm11 2014-10-05 23:31:39)

  • lpm11
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2010-11-10
  • Posty: 6

Odp: Openwrt dla netiaspot

Odświeżam temat... budujemy (ja z pomocą ScApi) obrazy BB. Poza pewnymi rzeczami wszystko działa - na razie jeszcze do testów. Szczegóły na superspot.pl

17 Odpowiedź przez JarekMk

  • Zarejestrowany: 2014-11-09
  • Posty: 328

Odp: Openwrt dla netiaspot

Ktoś coś?

JarekMk's Strona

18 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

JarekMk napisał/a:

Ktoś coś?

Napisałeś w wątku martwym od 3 lat. Nie pomyliłeś się?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

19 Odpowiedź przez JarekMk

  • Zarejestrowany: 2014-11-09
  • Posty: 328

Odp: Openwrt dla netiaspot

Nie. Może się zmieniło.
Dostałem ofertę kupna 100 sztuk po 20 zł per sztuka i stąd takie pytanie.

JarekMk's Strona

20 Odpowiedź przez porcsa

  • porcsa
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2017-12-30
  • Posty: 19

Odp: Openwrt dla netiaspot

JarekMk napisał/a:

Nie. Może się zmieniło.
Dostałem ofertę kupna 100 sztuk po 20 zł per sztuka i stąd takie pytanie.

Jaki konkretnie model ?



Mam pytanko ktoś bawił się netiaspot 2 ? Jest on na procku:  Lantiq XWAY VRX268

Log z uruchomienia systemu wygląda tak :

ROM VER: 1.1.4
CFG 05

ROM VER: 1.1.4
CFG 05


U-Boot 2010.06-LANTIQ-v-2.0.40 (Jan 02 2013 - 10:10:59 on albert@actaeon)

CLOCK CPU 333M RAM 166M
DRAM:  64 MiB
NAND:  NAND device: Manufacturer ID: 0x98, Chip ID: 0x76 (Toshiba NAND 64MiB 3,3V 8-bit)
64 MiB

----------------------------

i koniec, nic więcej się nie pojawia, chociaż router się normalnie uruchamia

21 Odpowiedź przez RGW

  • RGW
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-12-14
  • Posty: 165

Odp: Openwrt dla netiaspot

Leży u mnie taki router kilka razy próbowałem na nim postawić openwrt i wykorzystać go zamiast starego dlinka z wydaniem backfire. Wgrany openwrt  v0.95 ( 14.07 ) na nowszy openwrt 18 raczej nie ma co liczyć . Problem jest taki, że ma on 4 porty eth, jeden jest podpisany jako wan i chyba nie da rady go przepiąć jako lan, natomiast 3 powinny działać jako lan. Problem jest taki, że tylko 2 działają jako lan, 3 jest nieaktywny, nie wiem jak go zmusić aby działał jako lan. Jak usuwam interfejs wan, wan6 to tracę kontakt z routerem. Jak dodaje porty 0 i 4 w switchu jako nietagowane to dalej nie działa na tych portach lan.

konfiguracja network

config interface 'loopback'
    option ifname 'lo'
    option proto 'static'
    option ipaddr '127.0.0.1'
    option netmask '255.0.0.0'

config globals 'globals'
    option ula_prefix ''

config interface 'lan'
    option force_link '1'
    option type 'bridge'
    option proto 'static'
    option netmask '255.255.255.0'
    option ip6assign '60'
    option macaddr '00:00:00:00:00:00'
    option ipaddr '192.168.1.2'
    option gateway '192.168.1.1'
    option dns '8.8.8.8 8.8.4.4'
    option ifname 'eth0.1 mtlk0'

config switch
    option name 'switch0'
    option reset '1'
    option enable_vlan '1'

config switch_vlan
    option device 'switch0'
    option vlan '1'
    option vid '1'
    option ports '1 2 3 5 6t'

config atm-bridge 'atm'
    option vpi '0'
    option vci '35'
    option encaps 'llc'
    option payload 'bridged'

config interface 'wan'
    option ifname 'nas0'
    option proto 'pppoe'
    option username 'username'
    option password 'password'
    option ipv6 '1'

config interface 'wan6'
    option ifname '@wan'
    option proto 'dhcpv6'

config adsl 'dsl'
    option annex 'a'
    option firmware '/lib/firmware/adsl.bin'

config interface 'wwan'
    option proto 'dhcp'

info o switchu 

root@OpenWrt:/# swconfig list
Found: switch0 - eth0
root@OpenWrt:/# swconfig dev switch0 help
switch0: eth0(Lantiq PSB6970), ports: 7 (cpu @ 6), vlans: 16
     --switch
        Attribute 1 (int): enable_vlan (Enable VLAN mode)
        Attribute 2 (none): apply (Activate changes in the hardware)
        Attribute 3 (none): reset (Reset the switch)
     --vlan
        Attribute 1 (int): vid (VLAN ID (0-4094))
        Attribute 2 (ports): ports (VLAN port mapping)
     --port
        Attribute 1 (int): pvid (Primary VLAN ID)
root@OpenWrt:/#
ThinClient fan

22 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

Podłącz się do niego. Włóż kabel do każdego portu i zrób

swconfig dev switch0 show

I patrz który wyświetla się port z włożonym kablem. Jeżeli któryś się nie pokaże to bez zmiany kodu nic nie zrobisz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

23 Odpowiedź przez RGW

  • RGW
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-12-14
  • Posty: 165

Odp: Openwrt dla netiaspot

Zrobiłem po kolei z każdym portem, od góry pierwsze 2 działające  oznaczone na routerze jako eth 3 i eth2
2 ostanie oznaczone jako eth1 i wan, a i naporcie eth1 (czyli tym nie działającym opisanym jako eth1) łapie link bo świeci się dioda w karcie, natomiast na porcie wan nie łapie nawet linku.

root@OpenWrt:/# swconfig dev switch0 show
Global attributes:
        enable_vlan: 1
Port 0:
        pvid: 0
Port 1:
        pvid: 1
Port 2:
        pvid: 1
Port 3:
        pvid: 1
Port 4:
        pvid: 0
Port 5:
        pvid: 0
Port 6:
        pvid: 0
VLAN 1:
        vid: 1
        ports: 1 2 3 6t
root@OpenWrt:/# swconfig dev switch0 show
Global attributes:
        enable_vlan: 1
Port 0:
        pvid: 0
Port 1:
        pvid: 1
Port 2:
        pvid: 1
Port 3:
        pvid: 1
Port 4:
        pvid: 0
Port 5:
        pvid: 0
Port 6:
        pvid: 0
VLAN 1:
        vid: 1
        ports: 1 2 3 6t
root@OpenWrt:/# swconfig dev switch0 show
Global attributes:
        enable_vlan: 1
Port 0:
        pvid: 0
Port 1:
        pvid: 1
Port 2:
        pvid: 1
Port 3:
        pvid: 1
Port 4:
        pvid: 0
Port 5:
        pvid: 0
Port 6:
        pvid: 0
VLAN 1:
        vid: 1
        ports: 1 2 3 6t
root@OpenWrt:/# swconfig dev switch0 show
Global attributes:
        enable_vlan: 1
Port 0:
        pvid: 0
Port 1:
        pvid: 1
Port 2:
        pvid: 1
Port 3:
        pvid: 1
Port 4:
        pvid: 0
Port 5:
        pvid: 0
Port 6:
        pvid: 0
VLAN 1:
        vid: 1
        ports: 1 2 3 6t
root@OpenWrt:/#

Nie wiem jak sprawdzić który port wstaje bo sprawdzam przez dmesg i logread -f i  nie wyskakuje żadne info, że wstał port. Cyklicznie pojawia się tylko

Wed Sep 19 20:49:37 2018 daemon.notice netifd: Interface 'wan' is now down
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Interface 'wan' is disabled
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Interface 'wan' is enabled
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Interface 'wan' is setting up now
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Network device 'nas0' link is down
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Interface 'wan' has link connectivity loss
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Network device 'nas0' link is up
Wed Sep 19 20:49:37 2018 daemon.notice netifd: Interface 'wan' has link connectivity
Wed Sep 19 20:49:37 2018 daemon.info pppd[6836]: Plugin rp-pppoe.so loaded.
Wed Sep 19 20:49:37 2018 daemon.info pppd[6836]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Wed Sep 19 20:49:37 2018 daemon.notice pppd[6836]: pppd 2.4.7 started by root, uid 0
ThinClient fan

24 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,935

Odp: Openwrt dla netiaspot

No właśnie swconfig to powinno pokazac, ale widać że wersji którą masz tego nie robi. Więc w sumie nie masz jak sprawdzić.

Zrób sobie vlana 1 z portów "0 1 2 3 4 5  6t", reboot  i zobaczy czy wszystkie porty odpowiadają.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

25 Odpowiedź przez RGW

  • RGW
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-12-14
  • Posty: 165

Odp: Openwrt dla netiaspot

Zaraz sprawdzę,

Jeszcze tylko bootlog po wstaniu 

Please press Enter to activate this console.
[   12.580000] NET: Registered protocol family 10
[   12.592000] NET: Registered protocol family 8
[   12.596000] NET: Registered protocol family 20
[   12.608000] PPP generic driver version 2.4.2
[   12.628000] nf_conntrack version 0.5.0 (442 buckets, 1768 max)
[   12.640000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.656000] IFX MEI Version 5.00.00
[   12.672000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   12.684000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.708000] ATM1.0.26    ATM (A1) firmware version 0.16
[   12.712000] ifxmips_atm: ATM init succeed
[   12.748000] NET: Registered protocol family 24
[   12.796000] xt_time: kernel timezone is -0000
[   21.480000] device eth0.1 entered promiscuous mode
[   21.484000] device eth0 entered promiscuous mode
[   21.492000] br-lan: port 1(eth0.1) entered forwarding state
[   21.496000] br-lan: port 1(eth0.1) entered forwarding state
[   23.500000] br-lan: port 1(eth0.1) entered forwarding state
procd: - init complete -
[   31.044000] jffs2: notice: (308) check_node_data: wrong data CRC in data node at 0x009b5968: read 0xb51a17ef, calculated 0x1468f8d.
ThinClient fan