Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → TP-Link WDR7500 v6
Strony Poprzednia 1 2 3 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Da się jakoś zrobić kopię tego fimware'u, żebym mógł go wgrać przez tftp? Bo jak bym chciał wrócić na oryginalny soft to muszę odlutować kość i programatorem wgrywać dumpa a nie chce mi się tego robić bo za dużo czasu schodzi 
No i tak ci nie działa to jaką kopię chcesz? Ponieważ robisz dopiero soft to raczej od razu wylutuj kość i albo w podstawkę albo w inny sposób, bo jeszcze nie raz go uwalisz.
Hi guys !!!
I have same router.
It have same chips : Qualcomm Atheros QCA9563 and Qualcomm Atheros QCA988x as Ubiquiti Unifi AC
https://wiki.openwrt.org/toh/ubiquiti/unifiac
https://dev.openwrt.org/changeset/48711
WDR6500
https://wiki.openwrt.org/toh/tp-link/tp … wdr6500_v2
But it has Realtek RTL8367S Gigabit Switch
https://wiki.openwrt.org/doc/techref/swconfig
If we modify openwrt Unifi AC firmware or WDR6500 by adding support for RTL8376S .... ?
Troche informacji :
- QCA9563 laczy sie ze switchem za pomoca SGMII
- sterowanie switchem za pomoca MDIO
Oto polaczenia:
Mozna by bylo wykorzystac na poczatek kod z sr3200/xd3200. , za wyjatkiem sterowania switchem.
Na poczatek przyjmijmy, ze jego inicjalizacja zajmie sie U-boot, a wiec proponowana zmiana:
static void __init sr3200_xd3200_common_setup(void)
{
u8 *mac = (u8 *) KSEG1ADDR(0x1fff0000);
ath79_register_m25p80(NULL);
- ath79_register_mdio(0, 0x0);
- mdiobus_register_board_info(sr3200_xd3200_mdio0_info,
ARRAY_SIZE(sr3200_xd3200_mdio0_info));
/* GMAC0 is connected to QCA8334/QCA8337N switch */
ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
ath79_eth0_data.phy_mask = BIT(0);
ath79_eth0_data.speed = SPEED_1000;
ath79_eth0_data.duplex = DUPLEX_FULL;
ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
ath79_register_eth(0);
ath79_register_wmac(mac + 0x1000, NULL);
ap91_pci_init(mac + 0x5000, NULL);
- ath79_gpio_direction_select(SR3200_XD3200_GPIO_LED_SYSTEM, true);
- ath79_gpio_direction_select(SR3200_XD3200_GPIO_LED_WLAN2G, true);
/* Mute LEDs on boot */
- gpio_set_value(SR3200_XD3200_GPIO_LED_SYSTEM, 1);
- gpio_set_value(SR3200_XD3200_GPIO_LED_WLAN2G, 1);
- ath79_gpio_output_select(SR3200_XD3200_GPIO_LED_SYSTEM, 0);
- ath79_gpio_output_select(SR3200_XD3200_GPIO_LED_WLAN2G, 0);
- ath79_register_gpio_keys_polled(-1, SR3200_XD3200_KEYS_POLL_INTERVAL,
ARRAY_SIZE(sr3200_xd3200_gpio_keys),
sr3200_xd3200_gpio_keys);
}Teraz skompilowac z initramfs, tak by flash'a nie ruszac, i zobaczyc czy ruszy 
A tu caly zrzut flash'a :
Nie wiem na ile rejestry tego dziwacznego switcha zgadzaja sie z innymi z rodziny,
w razie potrzeby zrzuce przebiegi na MDIO oscyloskopem czy tam analizatorem logicznym.
W przyszlosci przydal by sie tez porzadny u-boot, moze @pepe2k ma cos schowane w szafladzie?
Ktos chetny do pomocy?
update 17.10.2017
I skompilowalem initramfs, ale cos nie bardzo widac efekt..
ath> bootm 0x80060400
## Booting image at 80060400 ...
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 00000000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...I na tym koniec na UART
Moze ktos ma pomysly?
Po odpieciu MDIO switcha od CPU switch pozostal w stanie wylaczonym,
czyli trzeba przeslac mu ustawienia zeby wogole eth dzialal.
Poprobowalem jeszcze z obrazami, jednak zaden nie dal mi nic na UART.
Serio nikt nie jest zainteresowany tym sprzetem?
Sprzęt kilkuletni, dostępny w sumie tylko w chinach. Jakie prawdopodobieństwo że ktoś go u nas ma? Tym bardziej że w europie dostępny jest jego odpowiednik.
Sprawdzałeś czy pandorabox nie ma wsparcia dla niego?
Z tego co widze to nie ma go w pandorabox.
Mysle ze znajdzie sie pare urzadzen w Polsce jak i europie
Uwazam, ze temat jest do ruszenia, tylko poczatki nieco kiepskie..
Zeby chociaz cokolwiek sie kernel odezwal, a potem juz pojdzie,
update 17.10.2017
I skompilowalem initramfs, ale cos nie bardzo widac efekt..
ath> bootm 0x80060400 ## Booting image at 80060400 ... Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 00000000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ...I na tym koniec na UART
Moze ktos ma pomysly?
Tutaj jest problem: ## Transferring control to Linux (at address 00000000) ...
Poza tym, dwa razy U-Boot, podpisany firmware... na oficjalne wsparcie nie licz. Ot, cudak, na którego naprawdę szkoda czasu.
No wlasnie ta linijka mi nie pasowala.
Na co to moze wskazywac? Moze jakas podpowiedz?
Sprzet jak sprzet, switcha ma tylko dziwacznego.
Jesli tylko kernel zaczal by sie uruchamiac, to bedzie sens zeby
zrzucic i zdekodowac transmisje po MDIO z konfiguracja switcha.
Puki co to za pomoca polecenia w bootloaderze odczytalem jakies
tam rejestry, choc zbyt serio do tych odczytow nie podchodze.
Read phy_reg 0x0 : 0x0
Read phy_reg 0x1 : 0x10
Read phy_reg 0x2 : 0x0
Read phy_reg 0x3 : 0x0
Read phy_reg 0x4 : 0x0
Read phy_reg 0x5 : 0x0
Read phy_reg 0x6 : 0x0
Read phy_reg 0x7 : 0x0
Read phy_reg 0x8 : 0x0
Read phy_reg 0x9 : 0x0
Read phy_reg 0xa : 0x0
Read phy_reg 0xb : 0x0
Read phy_reg 0xc : 0x0
Read phy_reg 0xd : 0x0
Read phy_reg 0xe : 0x48b0
Read phy_reg 0xf : 0xffff
Read phy_reg 0x10 : 0x1
Read phy_reg 0x11 : 0x0
Read phy_reg 0x12 : 0x0
Read phy_reg 0x13 : 0x4
Read phy_reg 0x14 : 0xffff
Read phy_reg 0x15 : 0x0
Read phy_reg 0x16 : 0x0
Read phy_reg 0x17 : 0x0
Read phy_reg 0x18 : 0xf00
Read phy_reg 0x19 : 0x0
Read phy_reg 0x1a : 0x0
Read phy_reg 0x1b : 0x0
Read phy_reg 0x1c : 0x0
Read phy_reg 0x1d : 0x0
Read phy_reg 0x1e : 0x0
Read phy_reg 0x1f : 0x1
Read phy_reg 0x20 : 0x0
Read phy_reg 0x21 : 0x10
Read phy_reg 0x22 : 0x0
Read phy_reg 0x23 : 0x0
Read phy_reg 0x24 : 0x0
Read phy_reg 0x25 : 0x0
Read phy_reg 0x26 : 0x0
Read phy_reg 0x27 : 0x0
Read phy_reg 0x28 : 0x0
Read phy_reg 0x29 : 0x0
Read phy_reg 0x30 : 0x1
Read phy_reg 0x31 : 0x0
Read phy_reg 0x32 : 0x0
Read phy_reg 0x33 : 0x4
Read phy_reg 0x34 : 0xffff
Read phy_reg 0x35 : 0x0
Read phy_reg 0x36 : 0x0
Read phy_reg 0x37 : 0x0
Read phy_reg 0x38 : 0xf00
Read phy_reg 0x39 : 0x0
Read phy_reg 0x40 : 0x0
Read phy_reg 0x41 : 0x10
Read phy_reg 0x42 : 0x0
Read phy_reg 0x43 : 0x0
Read phy_reg 0x44 : 0x0
Read phy_reg 0x45 : 0x0
Read phy_reg 0x46 : 0x0
Read phy_reg 0x47 : 0x0
Read phy_reg 0x48 : 0x0
Read phy_reg 0x49 : 0x0
Read phy_reg 0x50 : 0x1
Read phy_reg 0x51 : 0x0
Read phy_reg 0x52 : 0x0
Read phy_reg 0x53 : 0x23
Read phy_reg 0x54 : 0xffff
Read phy_reg 0x55 : 0x0
Read phy_reg 0x56 : 0x1
Read phy_reg 0x57 : 0x0
Read phy_reg 0x58 : 0xf00
Read phy_reg 0x59 : 0x0
Read phy_reg 0x60 : 0x0A jesli o uboot'a chodzi, to od sporego czasu patrze czy cos tam
sie u Ciebie rusza na QCA956x
Obstawiam, że oryginalny U-Boot nie rozumie nagłówka i stąd zerowy adres.
Pewnie kernel też wypakował gdzieś w kosmos.
Ok, dzieki za podpowiedz.
Sprawa sie nieco wyjasnila.
Zastanawiam sie czy nie podejsc do tego z innej strony,
czyli od wymiany pierwszego bootloadera.
Spojrze na kody od WR1043 V4, gdzie tez jest QCA9563, a
jutro jak sie uda zrzuce transmisje MDIO ustawiajaca switcha.
Moze uda mi sie to jakos do kupy skleic.
Co o takim podejsciu myslisz?
Ok, dzieki za podpowiedz.
Sprawa sie nieco wyjasnila.Zastanawiam sie czy nie podejsc do tego z innej strony,
czyli od wymiany pierwszego bootloadera.Spojrze na kody od WR1043 V4, gdzie tez jest QCA9563, a
jutro jak sie uda zrzuce transmisje MDIO ustawiajaca switcha.Moze uda mi sie to jakos do kupy skleic.
Co o takim podejsciu myslisz?
Jak Ci się nudzi i nie masz nic lepszego do roboty, to czemu nie
MDIO bym na razie zostawił i się tym w ogóle nie przejmował, raczej nie tędy droga - narobisz się niepotrzebnie na zapas. Pewnie dostępny sterownik będzie z tym działał. Uruchom na początek kernel.
Przebiegi z bootloadera, ktore ustawiaja switch zrzucone, jutro je opracuje i wyciagne juz konkretne
zapisywane i odczytywane adresy oraz dane. Moze faktycznie jakies stery beda pasowac, trzeba porownac.
Drugi bootloader wykonuje polecenie
bootcmd=bootm 0x9f040000A pod adresem 0x40000 w flash'u taki oto naglowek sie znajduje:
00 00 01 00 55 AA 9D D1 A8 C8 83 31 C9 69 FB BF
BC F0 D4 32 70 C7 AA 55 80 06 00 00 80 06 00 00
00 00 00 00 00 00 00 09 00 00 00 00 00 01 D8 00
00 01 D8 00 00 00 08 00 00 01 E0 00 00 00 20 00
00 02 00 00 00 01 00 00 00 03 00 00 00 01 00 00
00 04 00 00 00 00 02 00 00 04 02 00 00 10 00 7C
00 14 02 7C 00 56 FD 84 00 6B 00 00 00 15 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DA C2 BF 10 6E C5 C8 D7 15 29 E5 A0 5E F8 3E B3
F7 2C 45 0A C3 D8 D9 DC BC 3D 3B B5 2C DB 9A 92
FA EB BB B5 0E 14 8A F4 B5 E7 C2 FE FB BD 0C B8
57 44 52 37 35 30 30 56 36 00 00 00 00 00 00 02
B7 04 64 ED B4 28 5E 5F 58 22 F6 6F CF 0F A5 8C
E6 D1 C7 6D 2D 60 24 D1 84 DC D8 84 73 65 D6 6D
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00Daje on takie informacje:
struct fw_header {
uint32_t version; /* 0x00: header version */ --> 00 00 01 00
char fw_version[48]; /* 0x04: fw version string */ --> 55 AA 9D D1 A8 C8 83 31 C9 69 FB BF BC F0 D4 32 70 C7 AA 55 80 06 00 00 80 06 00 00 00 00 00 00 00 00 00 09 00 00 00 00 00 01 D8 00 00 01 D8 00
uint32_t hw_id; /* 0x34: product id */ --> 00 00 08 00
uint32_t hw_ver; /* 0x38: product version */ --> 00 01 E0 00
uint32_t add_hw_ver; /* 0x3c: additional hardware version */ --> 00 00 20 00
uint8_t md5sum1[MD5SUM_LEN]; /* 0x40 */ --> 00 02 00 00 00 01 00 00 00 03 00 00 00 01 00 00
uint32_t unk1; /* 0x50: 0x00000000 */ --> 00 04 00 00
uint8_t md5sum2[MD5SUM_LEN]; /* 0x54 */ --> 00 00 02 00 00 04 02 00 00 10 00 7C 00 14 02 7C
uint32_t unk2; /* 0x64: 0xffffffff */ --> 00 56 FD 84
uint32_t kernel_la; /* 0x68: kernel load address */ --> 00 6B 00 00
uint32_t kernel_ep; /* 0x6c: kernel entry point */ --> 00 15 00 00
uint32_t fw_length; /* 0x70: total length of the image */ --> 00 00 00 00
uint32_t kernel_ofs; /* 0x74: kernel data offset */ --> 00 00 00 00
uint32_t kernel_len; /* 0x78: kernel data length */ --> 00 00 00 00
uint32_t rootfs_ofs; /* 0x7c: rootfs data offset */ --> 00 00 00 00
uint32_t rootfs_len; /* 0x80: rootfs data length */ --> 00 00 00 00
uint32_t boot_ofs; /* 0x84: bootloader offset */ --> 00 00 00 00
uint32_t boot_len; /* 0x88: bootloader length */ --> 00 00 00 00
uint16_t magic1; /* 0x8c: swRevision[0] */--> 00 00
uint8_t sver_hi; /* 0x8e: swRevision[1] */ --> 00
uint8_t sver_lo; /* 0x8f: swRevision[2] */ --> 00
uint8_t magic2; /* 0x90: platformVer[0] */ --> DA
uint8_t ver_hi; /* 0x91: platformVer[1] */ --> C2
uint8_t ver_mid; /* 0x92: platformVer[2] */ --> BF
uint8_t ver_lo; /* 0x93: platformVer[3] */ --> 10
uint32_t unk3; /* 0x94: FIXME: changing value */ --> 6E C5 C8 D7
uint8_t sig1[128]; /* 0xD0: signature (boot)+kernel+rootfs */ --> B7 04 64 ED B4 28 5E 5F 58 22 F6 6F CF 0F A5 8C E6 D1 C7 6D 2D 60 24 D1 84 DC D8 84 73 65 D6 6D
uint8_t sig2[128]; /* 0x150: unused: 0x00 */
uint8_t pad[48];
}A to jest fragment bootlog'u :
## Booting image at 9f040000 ...
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864I tu cos mi ten adres 0x80060000 kupy sie nie trzyma z naglowkiem (?)
Dane sterujace switchem zdekodowane, wyglada na to, ze dosc podobny to RTL8367C
Oto dane, wraz z nazwami rejestrow:
Write/Read MDIO addr : MDIO data RTL8370 ASIC address, data
W 0x1F:0x000E W 0x17:0x2002 W 0x15:0x0001 R 0x19:0x001C R Addr:0x2002 = 0x001C PHY 0, reg 0x02
W 0x1F:0x000E W 0x17:0x13C2 W 0x18:0x0249 W 0x15:0x0003 W Addr:0x13C2 = 0x0249
W 0x1F:0x000E W 0x17:0x1301 W 0x15:0x0001 R 0x19:0x00A0 R Addr:0x1301 = 0x00A0
W 0x1F:0x000E W 0x17:0x13C2 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x13C2 = 0x0000
W 0x1F:0x000E W 0x17:0x0018 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0018 = 0x0C00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0018 = 0x0C00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0018 = 0x0C00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0018 = 0x0C00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0018 = 0x0C00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x18:0x0E00 W 0x15:0x0003 W Addr:0x0018 = 0x0E00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x15:0x0001 R 0x19:0x0E00 R Addr:0x0018 = 0x0E00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x0018 W 0x18:0x0F00 W 0x15:0x0003 W Addr:0x0018 = 0x0F00 RTL8367C_REG_PORT0_EEECFG
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2014 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2014 = 0x0000 PHY 0, reg 0x14
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2014 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x2014 = 0x0000 PHY 0, reg 0x14
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2708 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2708 = 0x0000 rtl8367c_getAsicPHYOCPReg
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2708 W 0x18:0x0006 W 0x15:0x0003 W Addr:0x2708 = 0x0006 rtl8367c_setAsicPHYOCPReg
W 0x1F:0x000E W 0x17:0x0038 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0038 = 0x0C00 --//--
W 0x1F:0x000E W 0x17:0x0038 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0038 = 0x0C00
W 0x1F:0x000E W 0x17:0x0038 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0038 = 0x0C00
W 0x1F:0x000E W 0x17:0x0038 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0038 = 0x0C00
W 0x1F:0x000E W 0x17:0x0038 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0038 = 0x0C00
W 0x1F:0x000E W 0x17:0x0038 W 0x18:0x0E00 W 0x15:0x0003 W Addr:0x0038 = 0x0E00
W 0x1F:0x000E W 0x17:0x0038 W 0x15:0x0001 R 0x19:0x0E00 R Addr:0x0038 = 0x0E00
W 0x1F:0x000E W 0x17:0x0038 W 0x18:0x0F00 W 0x15:0x0003 W Addr:0x0038 = 0x0F00
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2034 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2034 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2034 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x2034 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2728 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2728 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2728 W 0x18:0x0006 W 0x15:0x0003 W Addr:0x2728 = 0x0006
W 0x1F:0x000E W 0x17:0x0058 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0058 = 0x0C00 --//--
W 0x1F:0x000E W 0x17:0x0058 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0058 = 0x0C00
W 0x1F:0x000E W 0x17:0x0058 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0058 = 0x0C00
W 0x1F:0x000E W 0x17:0x0058 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0058 = 0x0C00
W 0x1F:0x000E W 0x17:0x0058 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0058 = 0x0C00
W 0x1F:0x000E W 0x17:0x0058 W 0x18:0x0E00 W 0x15:0x0003 W Addr:0x0058 = 0x0E00
W 0x1F:0x000E W 0x17:0x0058 W 0x15:0x0001 R 0x19:0x0E00 R Addr:0x0058 = 0x0E00
W 0x1F:0x000E W 0x17:0x0058 W 0x18:0x0F00 W 0x15:0x0003 W Addr:0x0058 = 0x0F00
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2054 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2054 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2054 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x2054 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2748 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2748 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2748 W 0x18:0x0006 W 0x15:0x0003 W Addr:0x2748 = 0x0006
W 0x1F:0x000E W 0x17:0x0078 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0078 = 0x0C00 --//--
W 0x1F:0x000E W 0x17:0x0078 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0078 = 0x0C00
W 0x1F:0x000E W 0x17:0x0078 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0078 = 0x0C00
W 0x1F:0x000E W 0x17:0x0078 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0078 = 0x0C00
W 0x1F:0x000E W 0x17:0x0078 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0078 = 0x0C00
W 0x1F:0x000E W 0x17:0x0078 W 0x18:0x0E00 W 0x15:0x0003 W Addr:0x0078 = 0x0E00
W 0x1F:0x000E W 0x17:0x0078 W 0x15:0x0001 R 0x19:0x0E00 R Addr:0x0078 = 0x0E00
W 0x1F:0x000E W 0x17:0x0078 W 0x18:0x0F00 W 0x15:0x0003 W Addr:0x0078 = 0x0F00
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2074 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2074 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2074 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x2074 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2768 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2768 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2768 W 0x18:0x0006 W 0x15:0x0003 W Addr:0x2768 = 0x0006
W 0x1F:0x000E W 0x17:0x0098 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0098 = 0x0C00 --//--
W 0x1F:0x000E W 0x17:0x0098 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0098 = 0x0C00
W 0x1F:0x000E W 0x17:0x0098 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0098 = 0x0C00
W 0x1F:0x000E W 0x17:0x0098 W 0x18:0x0C00 W 0x15:0x0003 W Addr:0x0098 = 0x0C00
W 0x1F:0x000E W 0x17:0x0098 W 0x15:0x0001 R 0x19:0x0C00 R Addr:0x0098 = 0x0C00
W 0x1F:0x000E W 0x17:0x0098 W 0x18:0x0E00 W 0x15:0x0003 W Addr:0x0098 = 0x0E00
W 0x1F:0x000E W 0x17:0x0098 W 0x15:0x0001 R 0x19:0x0E00 R Addr:0x0098 = 0x0E00
W 0x1F:0x000E W 0x17:0x0098 W 0x18:0x0F00 W 0x15:0x0003 W Addr:0x0098 = 0x0F00
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2094 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2094 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2094 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x2094 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2788 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x2788 = 0x0000
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2788 W 0x18:0x0006 W 0x15:0x0003 W Addr:0x2788 = 0x0006
W 0x1F:0x000E W 0x17:0x13EB W 0x18:0x15BB W 0x15:0x0003 W Addr:0x13EB = 0x15BB RTL8367C_REG_UTP_FIB_DET
W 0x1F:0x000E W 0x17:0x1303 W 0x18:0x06D6 W 0x15:0x0003 W Addr:0x1303 = 0x06D6 RTL8367C_REG_CHIP_DEBUG0
W 0x1F:0x000E W 0x17:0x1304 W 0x18:0x0700 W 0x15:0x0003 W Addr:0x1304 = 0x0700 RTL8367C_REG_CHIP_DEBUG1
W 0x1F:0x000E W 0x17:0x13E2 W 0x18:0x003F W 0x15:0x0003 W Addr:0x13E2 = 0x003F RTL8367C_REG_CHIP_DEBUG2
W 0x1F:0x000E W 0x17:0x13F9 W 0x18:0x0090 W 0x15:0x0003 W Addr:0x13F9 = 0x0090 RTL8367C_REG_EXT_TXC_DLY
W 0x1F:0x000E W 0x17:0x121E W 0x18:0x03CA W 0x15:0x0003 W Addr:0x121E = 0x03CA RTL8367C_REG_FLOWCTRL_ALL_ON
W 0x1F:0x000E W 0x17:0x1233 W 0x18:0x0352 W 0x15:0x0003 W Addr:0x1233 = 0x0352 RTL8367C_REG_FLOWCTRL_JUMBO_SYS_ON
W 0x1F:0x000E W 0x17:0x1237 W 0x18:0x00A0 W 0x15:0x0003 W Addr:0x1237 = 0x00A0 RTL8367C_REG_FLOWCTRL_JUMBO_PORT_ON
W 0x1F:0x000E W 0x17:0x123A W 0x18:0x0030 W 0x15:0x0003 W Addr:0x123A = 0x0030 RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_OFF
W 0x1F:0x000E W 0x17:0x1239 W 0x18:0x0084 W 0x15:0x0003 W Addr:0x1239 = 0x0084 RTL8367C_REG_FLOWCTRL_JUMBO_PORT_PRIVATE_ON
W 0x1F:0x000E W 0x17:0x0301 W 0x18:0x1000 W 0x15:0x0003 W Addr:0x0301 = 0x1000 RTL8367C_REG_SCHEDULE_WFQ_BURST_SIZE
W 0x1F:0x000E W 0x17:0x1349 W 0x18:0x001F W 0x15:0x0003 W Addr:0x1349 = 0x001F RTL8367C_REG_BYPASS_ABLTY_LOCK
W 0x1F:0x000E W 0x17:0x18E0 W 0x15:0x0001 R 0x19:0x4004 R Addr:0x18E0 = 0x4004 RTL8367C_REG_RLDP_CTRL0
W 0x1F:0x000E W 0x17:0x18E0 W 0x18:0x4004 W 0x15:0x0003 W Addr:0x18E0 = 0x4004 RTL8367C_REG_RLDP_CTRL0
W 0x1F:0x000E W 0x17:0x122B W 0x15:0x0001 R 0x19:0x641C R Addr:0x122B = 0x641C RTL8367C_REG_RRCP_CTRL0
W 0x1F:0x000E W 0x17:0x122B W 0x18:0x641C W 0x15:0x0003 W Addr:0x122B = 0x641C RTL8367C_REG_RRCP_CTRL0
W 0x1F:0x000E W 0x17:0x1305 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x1305 = 0x0000 RTL8367C_REG_DIGITAL_INTERFACE_SELECT
W 0x1F:0x000E W 0x17:0x1305 W 0x18:0xC000 W 0x15:0x0003 W Addr:0x1305 = 0xC000 RTL8367C_REG_DIGITAL_INTERFACE_SELECT
W 0x1F:0x000E W 0x17:0x1200 W 0x15:0x0001 R 0x19:0x7FCB R Addr:0x1200 = 0x7FCB RTL8367C_REG_MAX_LENGTH_LIMINT_IPG
W 0x1F:0x000E W 0x17:0x1200 W 0x18:0x7FCB W 0x15:0x0003 W Addr:0x1200 = 0x7FCB RTL8367C_REG_MAX_LENGTH_LIMINT_IPG
W 0x1F:0x000E W 0x17:0x0884 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x0884 = 0x0000 RTL8367C_REG_MAX_LEN_RX_TX
W 0x1F:0x000E W 0x17:0x0884 W 0x18:0x0003 W 0x15:0x0003 W Addr:0x0884 = 0x0003 RTL8367C_REG_MAX_LEN_RX_TX
W 0x1F:0x000E W 0x17:0x06EB W 0x15:0x0001 R 0x19:0x0000 R Addr:0x06EB = 0x0000 RTL8367C_REG_ACL_ACCESS_MODE
W 0x1F:0x000E W 0x17:0x06EB W 0x18:0x0001 W 0x15:0x0003 W Addr:0x06EB = 0x0001 RTL8367C_REG_ACL_ACCESS_MODE
W 0x1F:0x000E W 0x17:0x00CF W 0x18:0xFFFF W 0x15:0x0003 W Addr:0x00CF = 0xFFFF RTL8367C_REG_INGRESSBW_PORT6_RATE_CTRL0
W 0x1F:0x000E W 0x17:0x00D0 W 0x15:0x0001 R 0x19:0x0001 R Addr:0x00D0 = 0x0001 RTL8367C_REG_INGRESSBW_PORT6_RATE_CTRL1
W 0x1F:0x000E W 0x17:0x00D0 W 0x18:0x0007 W 0x15:0x0003 W Addr:0x00D0 = 0x0007 RTL8367C_REG_INGRESSBW_PORT6_RATE_CTRL1
W 0x1F:0x000E W 0x17:0x00CE W 0x15:0x0001 R 0x19:0x48B0 R Addr:0x00CE = 0x48B0 RTL8367C_REG_PORT6_MISC_CFG
W 0x1F:0x000E W 0x17:0x00CE W 0x18:0x48B0 W 0x15:0x0003 W Addr:0x00CE = 0x48B0 RTL8367C_REG_PORT6_MISC_CFG
W 0x1F:0x000E W 0x17:0x00CE W 0x15:0x0001 R 0x19:0x48B0 R Addr:0x00CE = 0x48B0 RTL8367C_REG_PORT6_MISC_CFG
W 0x1F:0x000E W 0x17:0x00CE W 0x18:0x48B0 W 0x15:0x0003 W Addr:0x00CE = 0x48B0 RTL8367C_REG_PORT6_MISC_CFG
W 0x1F:0x000E W 0x17:0x0398 W 0x18:0xFFFF W 0x15:0x0003 W Addr:0x0398 = 0xFFFF RTL8367C_REG_PORT6_EGRESSBW_CTRL0
W 0x1F:0x000E W 0x17:0x0399 W 0x15:0x0001 R 0x19:0x0001 R Addr:0x0399 = 0x0001 RTL8367C_REG_PORT6_EGRESSBW_CTRL1
W 0x1F:0x000E W 0x17:0x0399 W 0x18:0x0007 W 0x15:0x0003 W Addr:0x0399 = 0x0007 RTL8367C_REG_PORT6_EGRESSBW_CTRL1
W 0x1F:0x000E W 0x17:0x0300 W 0x15:0x0001 R 0x19:0x0001 R Addr:0x0300 = 0x0001 RTL8367C_REG_SCHEDULE_WFQ_CTRL
W 0x1F:0x000E W 0x17:0x0300 W 0x18:0x0001 W 0x15:0x0003 W Addr:0x0300 = 0x0001 RTL8367C_REG_SCHEDULE_WFQ_CTRL
W 0x1F:0x000E W 0x17:0x03FA W 0x18:0x0007 W 0x15:0x0003 W Addr:0x03FA = 0x0007 RTL8367C_REG_LINE_RATE_HSG_H
W 0x1F:0x000E W 0x17:0x08C8 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x08C8 = 0x0000 RTL8367C_REG_PORT_SECURITY_CTRL
W 0x1F:0x000E W 0x17:0x08C8 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x08C8 = 0x00C0 RTL8367C_REG_PORT_SECURITY_CTRL
W 0x1F:0x000E W 0x17:0x0A30 W 0x15:0x0001 R 0x19:0x0206 R Addr:0x0A30 = 0x0206 RTL8367C_REG_LUT_CFG
W 0x1F:0x000E W 0x17:0x0A30 W 0x18:0x020E W 0x15:0x0003 W Addr:0x0A30 = 0x020E RTL8367C_REG_LUT_CFG
W 0x1F:0x000E W 0x17:0x0800 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x0800 = 0x0000 RTL8367C_REG_RMA_CTRL00
W 0x1F:0x000E W 0x17:0x0800 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x0800 = 0x0000 RTL8367C_REG_RMA_CTRL00
W 0x1F:0x000E W 0x17:0x0802 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x0802 = 0x0000 RTL8367C_REG_RMA_CTRL02
W 0x1F:0x000E W 0x17:0x09DA W 0x15:0x0001 R 0x19:0x0013 R Addr:0x09DA = 0x0013 RTL8367C_REG_MIRROR_CTRL2
W 0x1F:0x000E W 0x17:0x09DA W 0x18:0x0017 W 0x15:0x0003 W Addr:0x09DA = 0x0017 RTL8367C_REG_MIRROR_CTRL2
W 0x1F:0x000E W 0x17:0x1D32 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x1D32 = 0x0000 RTL8367C_REG_IO_MISC_FUNC
W 0x1F:0x000E W 0x17:0x1D32 W 0x18:0x0002 W 0x15:0x0003 W Addr:0x1D32 = 0x0002 RTL8367C_REG_IO_MISC_FUNC
W 0x1F:0x000E W 0x17:0x130F W 0x15:0x0001 R 0x19:0x087D R Addr:0x130F = 0x087D RTL8367C_REG_PHY_AD
W 0x1F:0x000E W 0x17:0x130F W 0x18:0x085D W 0x15:0x0003 W Addr:0x130F = 0x085D RTL8367C_REG_PHY_AD
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2000 W 0x15:0x0001 R 0x19:0x1940 R Addr:0x2000 = 0x1940 PHY 0, reg 0x00
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2000 W 0x18:0x1340 W 0x15:0x0003 W Addr:0x2000 = 0x1340 PHY 0, reg 0x00
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2020 W 0x15:0x0001 R 0x19:0x1940 R Addr:0x2020 = 0x1940
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2020 W 0x18:0x1340 W 0x15:0x0003 W Addr:0x2020 = 0x1340
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2040 W 0x15:0x0001 R 0x19:0x1940 R Addr:0x2040 = 0x1940
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2040 W 0x18:0x1340 W 0x15:0x0003 W Addr:0x2040 = 0x1340
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2060 W 0x15:0x0001 R 0x19:0x1940 R Addr:0x2060 = 0x1940
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2060 W 0x18:0x1340 W 0x15:0x0003 W Addr:0x2060 = 0x1340
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2080 W 0x15:0x0001 R 0x19:0x1940 R Addr:0x2080 = 0x1940
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2080 W 0x18:0x1340 W 0x15:0x0003 W Addr:0x2080 = 0x1340
W 0x1F:0x000E W 0x17:0x03F7 W 0x15:0x0001 R 0x19:0x0000 R Addr:0x03F7 = 0x0000 RTL8367C_REG_BYPASS_LINE_RATE
W 0x1F:0x000E W 0x17:0x03F7 W 0x18:0x0000 W 0x15:0x0003 W Addr:0x03F7 = 0x0000 RTL8367C_REG_BYPASS_LINE_RATE
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x7180 W 0x15:0x0003 W Addr:0x6602 = 0x7180 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0002 W 0x15:0x0003 W Addr:0x6601 = 0x0002 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x04D7 W 0x15:0x0003 W Addr:0x6602 = 0x04D7 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0480 W 0x15:0x0003 W Addr:0x6601 = 0x0480 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0xF994 W 0x15:0x0003 W Addr:0x6602 = 0xF994 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0481 W 0x15:0x0003 W Addr:0x6601 = 0x0481 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x31A2 W 0x15:0x0003 W Addr:0x6602 = 0x31A2 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0482 W 0x15:0x0003 W Addr:0x6601 = 0x0482 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x6960 W 0x15:0x0003 W Addr:0x6602 = 0x6960 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0483 W 0x15:0x0003 W Addr:0x6601 = 0x0483 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x9728 W 0x15:0x0003 W Addr:0x6602 = 0x9728 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0484 W 0x15:0x0003 W Addr:0x6601 = 0x0484 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x9D85 W 0x15:0x0003 W Addr:0x6602 = 0x9D85 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0423 W 0x15:0x0003 W Addr:0x6601 = 0x0423 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0xD810 W 0x15:0x0003 W Addr:0x6602 = 0xD810 RTL8367C_REG_SDS_INDACS_DATA
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0424 W 0x15:0x0003 W Addr:0x6601 = 0x0424 RTL8367C_REG_SDS_INDACS_ADR
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0 RTL8367C_REG_SDS_INDACS_CMD
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1500 R Addr:0x1D11 = 0x1500 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x1540 W 0x15:0x0003 W Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x1540 W 0x15:0x0003 W Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1305 W 0x15:0x0001 R 0x19:0xC000 R Addr:0x1305 = 0xC000 RTL8367C_REG_DIGITAL_INTERFACE_SELECT
W 0x1F:0x000E W 0x17:0x1305 W 0x18:0xC090 W 0x15:0x0003 W Addr:0x1305 = 0xC090 RTL8367C_REG_DIGITAL_INTERFACE_SELECT
W 0x1F:0x000E W 0x17:0x6602 W 0x18:0x7106 W 0x15:0x0003 W Addr:0x6602 = 0x7106
W 0x1F:0x000E W 0x17:0x6601 W 0x18:0x0003 W 0x15:0x0003 W Addr:0x6601 = 0x0003
W 0x1F:0x000E W 0x17:0x6600 W 0x18:0x00C0 W 0x15:0x0003 W Addr:0x6600 = 0x00C0
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x1540 W 0x15:0x0003 W Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x1540 W 0x15:0x0003 W Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1540 R Addr:0x1D11 = 0x1540 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x1740 W 0x15:0x0003 W Addr:0x1D11 = 0x1740 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x1740 R Addr:0x1D11 = 0x1740 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x3740 W 0x15:0x0003 W Addr:0x1D11 = 0x3740 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x15:0x0001 R 0x19:0x3740 R Addr:0x1D11 = 0x3740 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1D11 W 0x18:0x7740 W 0x15:0x0003 W Addr:0x1D11 = 0x7740 RTL8367C_REG_SDS_MISC
W 0x1F:0x000E W 0x17:0x1311 W 0x18:0x1076 W 0x15:0x0003 W Addr:0x1311 = 0x1076 RTL8367C_REG_DIGITAL_INTERFACE1_FORCE
W 0x1F:0x000E W 0x17:0x08A2 W 0x18:0x0040 W 0x15:0x0003 W Addr:0x08A2 = 0x0040 RTL8367C_REG_PORT_ISOLATION_PORT0_MASK
W 0x1F:0x000E W 0x17:0x08A3 W 0x18:0x005E W 0x15:0x0003 W Addr:0x08A3 = 0x005E RTL8367C_REG_PORT_ISOLATION_PORT1_MASK
W 0x1F:0x000E W 0x17:0x08A4 W 0x18:0x005E W 0x15:0x0003 W Addr:0x08A4 = 0x005E RTL8367C_REG_PORT_ISOLATION_PORT2_MASK
W 0x1F:0x000E W 0x17:0x08A5 W 0x18:0x005E W 0x15:0x0003 W Addr:0x08A5 = 0x005E RTL8367C_REG_PORT_ISOLATION_PORT3_MASK
W 0x1F:0x000E W 0x17:0x08A6 W 0x18:0x005E W 0x15:0x0003 W Addr:0x08A6 = 0x005E RTL8367C_REG_PORT_ISOLATION_PORT4_MASK
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2101 W 0x15:0x0001 R 0x19:0x0418 R Addr:0x2101 = 0x0418 rtl8367c_getAsicPHYOCPReg
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69 RTL8367C_REG_GPHY_OCP_MSB_0
W 0x1F:0x000E W 0x17:0x2101 W 0x18:0x0438 W 0x15:0x0003 W Addr:0x2101 = 0x0438 rtl8367c_setAsicPHYOCPReg
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2121 W 0x15:0x0001 R 0x19:0x0418 R Addr:0x2121 = 0x0418
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2121 W 0x18:0x0438 W 0x15:0x0003 W Addr:0x2121 = 0x0438
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2141 W 0x15:0x0001 R 0x19:0x0418 R Addr:0x2141 = 0x0418
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2141 W 0x18:0x0438 W 0x15:0x0003 W Addr:0x2141 = 0x0438
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2161 W 0x15:0x0001 R 0x19:0x0418 R Addr:0x2161 = 0x0418
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2161 W 0x18:0x0438 W 0x15:0x0003 W Addr:0x2161 = 0x0438
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69 --//--
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2181 W 0x15:0x0001 R 0x19:0x0418 R Addr:0x2181 = 0x0418
W 0x1F:0x000E W 0x17:0x1D15 W 0x15:0x0001 R 0x19:0x0A69 R Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x1D15 W 0x18:0x0A69 W 0x15:0x0003 W Addr:0x1D15 = 0x0A69
W 0x1F:0x000E W 0x17:0x2181 W 0x18:0x0438 W 0x15:0x0003 W Addr:0x2181 = 0x0438Jest to bardzo podobne do tego API:
https://github.com/RMerl/asuswrt-merlin … /rtl8365mb
Wrocilem do robienia kernela, jednak utknelem na tym, jak zrobic
obraz z initramfs oraz naglowkiem. Moze jakas mala podpowiedz jak dalej ruszyc?
Na początek to za dużo się zastanawiasz Dodaj po prostu do źródeł, bez kombinowania dodaj do image/Makefile jak dla innych tplinków jest zrobione i otrzymasz initramfs. Później będziesz się martwić o nagłówki do obrazów.
A tak w ogóle to weź sobie obraz initramfs od innego urządzenia który jest tym SoC i po prostu zobacz czy się uruchomi. Nie ważne że nie będzie obsługi sieci, wifi, led itd, ważne żeby się uruchomił.
No niestety probowalem i nie zadzialalo - patrz post 34.
Probowalem cos zrobic z WR1043v4, lecz tez naglowek ma sie
nijak do tego co opisalem..
Temu o pomoc pytam.
Więc jesteś w kropcie - bo to nie jest żaden standard co właściwie uboot chce uruchomić. Próbuj wszystko po kolei, może się coś uruchomi.
No wlasnie jak napisalem w poscie 39, druga ramka,
naglowek znaleziony we flash'u pasuje to dosc dobrze do
naglowka w wersji 3 (chyba).
Ten ponoc sie az tak bardzo nie rozni od poprzednich wersji,
a co przegladalem obrazy LEDE, to nic podobnego nie znalazlem.
====
Narazie wrocilem do u-boota.
Ten od WR1043v4 dziala, ale z jednym ale
Switch nie skonfigurowany, to eth nie ma.
Sprobuje wrzucic mu te dane po MDIO co wczesniej spisalem.
====
switch na nowym bootloaderze dziala
U-Boot 1.1.4 (Oct 22 2017 - 01:36:07)
ap152 - Dragonfly 1.0
DRAM: 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 366k for U-Boot at: 83fa4000
Reserving 192k for malloc() at: 83f74000
Reserving 44 Bytes for Board Info at: 83f73fd4
Reserving 36 Bytes for Global Data at: 83f73fb0
Reserving 128k for boot params() at: 83f53fb0
Stack Pointer at: 83f53f98
Now running in RAM - U-Boot at: 83fa4000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
MDIO read reg: 2002 val: 1C ,expected 1C
MDIO read reg: 1301 val: A0 ,expected A0
MDIO read reg: 18 val: C00 ,expected C00
MDIO read reg: 18 val: C00 ,expected C00
MDIO read reg: 18 val: C00 ,expected C00
MDIO read reg: 18 val: E00 ,expected E00
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2014 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2708 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 38 val: C00 ,expected C00
MDIO read reg: 38 val: C00 ,expected C00
MDIO read reg: 38 val: C00 ,expected C00
MDIO read reg: 38 val: E00 ,expected E00
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2034 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2728 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 58 val: C00 ,expected C00
MDIO read reg: 58 val: C00 ,expected C00
MDIO read reg: 58 val: C00 ,expected C00
MDIO read reg: 58 val: E00 ,expected E00
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2054 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2748 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 78 val: C00 ,expected C00
MDIO read reg: 78 val: C00 ,expected C00
MDIO read reg: 78 val: C00 ,expected C00
MDIO read reg: 78 val: E00 ,expected E00
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2074 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2768 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 98 val: C00 ,expected C00
MDIO read reg: 98 val: C00 ,expected C00
MDIO read reg: 98 val: C00 ,expected C00
MDIO read reg: 98 val: E00 ,expected E00
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2094 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2788 val: 0 ,expected 0
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 18E0 val: 4004 ,expected 4004
MDIO read reg: 122B val: 641C ,expected 641C
MDIO read reg: 1305 val: 0 ,expected 0
MDIO read reg: 1200 val: 7FCB ,expected 7FCB
MDIO read reg: 884 val: 0 ,expected 0
MDIO read reg: 6EB val: 0 ,expected 0
MDIO read reg: D0 val: 1 ,expected 1
MDIO read reg: CE val: 48B0 ,expected 48B0
MDIO read reg: CE val: 48B0 ,expected 48B0
MDIO read reg: 399 val: 1 ,expected 1
MDIO read reg: 300 val: 1 ,expected 1
MDIO read reg: 8C8 val: 0 ,expected 0
MDIO read reg: A30 val: 206 ,expected 206
MDIO read reg: 800 val: 0 ,expected 0
MDIO read reg: 9DA val: 13 ,expected 13
MDIO read reg: 1D32 val: 0 ,expected 0
MDIO read reg: 130F val: 87D ,expected 87D
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2000 val: 1940 ,expected 1940
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2020 val: 1940 ,expected 1940
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2040 val: 1940 ,expected 1940
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2060 val: 1940 ,expected 1940
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2080 val: 1940 ,expected 1940
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 3F7 val: 0 ,expected 0
MDIO read reg: 1D11 val: 1500 ,expected 1500
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1305 val: C000 ,expected C000
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1540 ,expected 1540
MDIO read reg: 1D11 val: 1740 ,expected 1740
MDIO read reg: 1D11 val: 3740 ,expected 3740
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2101 val: 418 ,expected 418
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2121 val: 418 ,expected 418
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2141 val: 418 ,expected 418
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2161 val: 418 ,expected 418
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 1D15 val: A69 ,expected A69
MDIO read reg: 2181 val: 418 ,expected 418
MDIO read reg: 1D15 val: A69 ,expected A69
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x4b962100
is_auto_upload_firmware=1
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.8; our IP address is 192.168.0.86
Filename 'wr1043ndv4_tp_recovery.bin'.
Load address: 0x80800000
Loading: *T T T eth0 up
eth0
Setting 0x181162c0 to 0x4b962100
is_auto_upload_firmware=1
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.8; our IP address is 192.168.0.86
Filename 'wr1043ndv4_tp_recovery.bin'.
Load address: 0x80800000
Loading: *
Abort
Firmware recovery: FLASH_SIZE = 16 filesize = 0x0.
Do cmd fwrecov 0x80800000 0x00000000
Usage:
fwrecov - TP-Link Firmware Recovery Tools
Autobooting in 5 seconds
delay key:<NULL>
delay key:<NULL>
stop key:<tpl>
stop key:<NULL>
tplgot stopkey
ap151>
ap151> tfttp 0x80060000 sr3200.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.214
Filename 'sr3200.bin'.
Load address: 0x80060000
Loading: *#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################
done
Bytes transferred = 3412457 (3411e9 hex)
ap151> Choc TPLink strasznie go okaleczyl..
Dopiescilem troche u-boota, poprawilem sterowniki od switcha i
podmienilem cmd_bootm.c i wszystko od lzma z repo Pepe2k.
Teraz wyglada to tak:
U-Boot 1.1.4 (Oct 22 2017 - 17:00:34)
ap152 - Dragonfly 1.0
DRAM: 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 360k for U-Boot at: 83fa4000
Reserving 192k for malloc() at: 83f74000
Reserving 44 Bytes for Board Info at: 83f73fd4
Reserving 36 Bytes for Global Data at: 83f73fb0
Reserving 128k for boot params() at: 83f53fb0
Stack Pointer at: 83f53f98
Now running in RAM - U-Boot at: 83fa4000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
RTL8376S switch config start
RTL8376S switch config done
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x4b962100
Enter 'tpl' to stop booting: 0
ap151> tftp 0x80060000 lede-17.01.4-ar71xx-generic-tl-wr1043nd-v4-squashfs-factory.bin
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-17.01.4-ar71xx-generic-tl-wr1043nd-v4-squashfs-factory.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########################################################
done
Bytes transferred = 3626198 (3754d6 hex)
ap151> bootm 0x80060000
Booting image from 0x80060000...
## Error: unsupported image headerJednak dalej mam problemy z uruchomieniem jakiegokolwiek obrazu, przyklady:
Filename 'lede-17.01.4-ar71xx-generic-tl-wr1043nd-v4-squashfs-factory.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###########################################################
done
Bytes transferred = 3626198 (3754d6 hex)
ap151> bootm 0x80060000
Booting image from 0x80060000...
## Error: unsupported image header
ap151> tftp 0x80060000 lede-ar71xx-generic-vmlinux-initramfs.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-ar71xx-generic-vmlinux-initramfs.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################################
done
Bytes transferred = 6171276 (5e2a8c hex)
ap151> bootm 0x80060000
Booting image from 0x80060000...
## Error: unsupported image header
ap151> tftp 0x80060000 lede-ar71xx-generic-uImage-initramfs-lzma.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-ar71xx-generic-uImage-initramfs-lzma.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################
done
Bytes transferred = 3239895 (316fd7 hex)
ap151> bootm 0x80060000
Booting image from 0x80060000...
Image name: MIPS OpenWrt Linux-4.4.92
Build date: 2017-10-17 17:43:06 UTC
Architecture: MIPS
OS/image type: Linux Kernel
Compression: LZMA
Data size: 3.1 MB (3239831 bytes)
Load address: 0x80060000
Entry point: 0x80060000
Header CRC... OK!
Data CRC... skipped
Uncompressing Kernel... ERROR
## Error: LZMA error '1'!
ap151> tftp lede-ar71xx-generic-vmlinux.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-ar71xx-generic-uImage-initramfs-lzma.bin'.
Load address: 0x0
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################
done
Bytes transferred = 3239895 (316fd7 hex)
ap151> tftp 0x80060000 lede-ar71xx-generic-vmlinux.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-ar71xx-generic-vmlinux.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 4276220 (413ffc hex)
ap151> bootm 0x80060000
Booting image from 0x80060000...
## Error: unsupported image header
ap151> tftp 0x80060000 lede-ar71xx-generic-uImage-initramfs-lzma.bin
Trying eth0
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-ar71xx-generic-uImage-initramfs-lzma.bin'.
Load address: 0x80060000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################
done
Bytes transferred = 3239895 (316fd7 hex)
ap151> bootm 0x80060000
Booting image from 0x80060000...
Image name: MIPS OpenWrt Linux-4.4.92
Build date: 2017-10-17 17:43:06 UTC
Architecture: MIPS
OS/image type: Linux Kernel
Compression: LZMA
Data size: 3.1 MB (3239831 bytes)
Load address: 0x80060000
Entry point: 0x80060000
Header CRC... OK!
Data CRC... skipped
Uncompressing Kernel... ERROR
## Error: LZMA error '1'!Czy informacje jak zrobic obraz z initramfs podana nizej jest
wlasciwa?
https://lede-project.org/docs/guide-dev … new_device
Przy okazji przydalo by sie zczytac ustawienia GPIO.
Najwygodniej bylo by z oryginalnego systemu.
W flash'u znalazlem takie info:
passwd:
root:$1$/e66eR0s$WEoPwBaGxca4PV69/cp/10:0:0:root:/root:/bin/ash
nobody:*:65534:65534:nobody:/var:/bin/false
admin:*:500:500:admin:/var:/bin/false
guest:*:500:500:guest:/var:/bin/false
ftp:*:55:55:ftp:/home/ftp:/bin/falseMoze ktos kojarzy to haslo?
Pierwszy sukces !!
Obraz sie odpala
ap151> tftp 0x80800000 lede-ar71xx-generic-uImage-initramfs-lzma.bin
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.1.8; our IP address is 192.168.1.73
Filename 'lede-ar71xx-generic-uImage-initramfs-lzma.bin'.
Load address: 0x80800000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################
done
Bytes transferred = 3239895 (316fd7 hex)
ap151> bootm 0x80800000
Booting image from 0x80800000...
Image name: MIPS OpenWrt Linux-4.4.92
Build date: 2017-10-17 17:43:06 UTC
Architecture: MIPS
OS/image type: Linux Kernel
Compression: LZMA
Data size: 3.1 MB (3239831 bytes)
Load address: 0x80060000
Entry point: 0x80060000
Header CRC... OK!
Data CRC... skipped
Uncompressing Kernel... OK!
## Bootargs: 'console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(uImage),15104k(rootfs),64k(config),64k(ART) '
## Transferring control to Linux (at address 0x80060000) ...
## Giving linux memsize in MB, 64
Starting kernel...
[ 0.000000] Linux version 4.4.92 (bizongod@bizonowo) (gcc version 5.5.0 (LEDE GCC 5.5.0 r5103-f6c4a9c) ) #0 Tue Oct 17 17:43:06 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: mem=64M console=ttyS0,120000 loglevel=7 root=/dev/ram0 rootfstype=ramfs board=SR3200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 58244K/65536K available (2996K kernel code, 144K rwdata, 756K rodata, 2176K init, 200K bss, 7292K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008203] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.071017] pid_max: default: 32768 minimum: 301
[ 0.075979] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.082959] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092507] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.102918] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.109922] NET: Registered protocol family 16
[ 0.115863] MIPS: machine is YunCore SR3200
[ 0.339275] registering PCI controller with io_map_base unset
[ 0.353768] PCI host bridge to bus 0000:00
[ 0.358139] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.365378] pci_bus 0000:00: root bus resource [io 0x0001]
[ 0.371254] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.378400] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.386809] pci 0000:00:00.0: invalid calibration data
[ 0.392578] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.400322] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.407933] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.413819] clocksource: Switched to clocksource MIPS
[ 0.420190] NET: Registered protocol family 2
[ 0.425454] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.432804] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.439547] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.446332] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.452500] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.459370] NET: Registered protocol family 1
[ 2.244323] Crashlog allocated RAM at address 0x3f00000
[ 2.261684] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.267881] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.315859] io scheduler noop registered
[ 2.319998] io scheduler deadline registered (default)
[ 2.325679] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.332708] console [ttyS0] disabled
[ 2.356559] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 2.365653] console [ttyS0] enabled
[ 2.365653] console [ttyS0] enabled
[ 2.372653] bootconsole [early0] disabled
[ 2.372653] bootconsole [early0] disabled
[ 2.383364] m25p80 spi0.0: found w25q128, expected m25p80
[ 2.388598] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 2.408665] libphy: ag71xx_mdio: probed
[ 2.995078] ag71xx ag71xx.0: no PHY found with phy_mask=00000001
[ 3.002347] NET: Registered protocol family 10
[ 3.009021] NET: Registered protocol family 17
[ 3.013357] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 3.025621] 8021q: 802.1Q VLAN Support v1.8
[ 3.043330] Freeing unused kernel memory: 2176K
[ 3.057410] init: Console is alive
[ 3.060849] init: - watchdog -
[ 3.076081] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.093088] usbcore: registered new interface driver usbfs
[ 3.098473] usbcore: registered new interface driver hub
[ 3.103636] usbcore: registered new device driver usb
[ 3.112867] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.120524] ehci-platform: EHCI generic platform driver
[ 3.125668] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.131384] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.141228] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.163851] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 3.170745] hub 1-0:1.0: USB hub found
[ 3.174687] hub 1-0:1.0: 1 port detected
[ 3.178749] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.184508] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.194381] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.213838] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 3.220713] hub 2-0:1.0: USB hub found
[ 3.224678] hub 2-0:1.0: 1 port detected
[ 3.230695] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.237840] ohci-platform: OHCI generic platform driver
[ 3.243474] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.260805] init: - preinit -
[ 3.400853] random: procd: uninitialized urandom read (4 bytes read, 5 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.497286] procd: - early -
[ 6.500130] procd: - watchdog -
[ 7.027029] procd: - watchdog -
[ 7.030250] procd: - ubus -
[ 7.038859] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.083233] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.092239] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.100976] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.109814] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.118508] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.127284] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.136090] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 7.145029] procd: - init -
Please press Enter to activate this console.
[ 7.277457] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.287143] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.302862] Loading modules backported from Linux version wt-2017-10-06-0-ga7a22fbbd1f0
[ 7.310585] Backport generated by backports.git v4.14-rc2-1-6-gedfb595c
[ 7.319372] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.330989] nf_conntrack version 0.5.0 (944 buckets, 3776 max)
[ 7.375111] xt_time: kernel timezone is -0000
[ 7.426725] PPP generic driver version 2.4.2
[ 7.432871] NET: Registered protocol family 24
[ 7.482931] Data bus error, epc == 82803774, ra == 82803774
[ 7.488284] Oops[#1]:
[ 7.490466] CPU: 0 PID: 353 Comm: kmodloader Not tainted 4.4.92 #0
[ 7.496387] task: 839bd928 ti: 83970000 task.ti: 83970000
[ 7.501557] $ 0 : 00000000 00000025 deadc0de 00000000
[ 7.506599] $ 4 : b8115f18 00015f18 00000007 00000004
[ 7.511641] $ 8 : 00000001 7c7c3c7c 7c7c7c7c 7c7c7c7c
[ 7.516683] $12 : 7c7c3c7c 94cb6583 00000000 7c7c7c3c
[ 7.521725] $16 : 00000064 82e08010 00000000 00015f18
[ 7.526767] $20 : 00000007 00000004 00000004 000003ff
[ 7.531809] $24 : 00000000 df93723e
[ 7.536851] $28 : 83970000 83971a10 83971a9c 82803774
[ 7.541894] Hi : 00000000
[ 7.544655] Lo : 00000064
[ 7.547455] epc : 82803774 ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 7.553137] ra : 82803774 ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 7.558808] Status: 1100cc03KERNEL EXL IE
[ 7.562845] Cause : 0080001c (ExcCode 07)
[ 7.566687] PrId : 00019750 (MIPS 74Kc)
[ 7.570447] Modules linked in: ath9k(+) ath9k_common pppoe ppp_async ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat ledtrig_usbport ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables ohci_platform ohci_hcd ehci_platform ehci_hcd gpio_button_hotplug usbcore nls_base usb_common
[ 7.633044] Process kmodloader (pid: 353, threadinfo=83970000, task=839bd928, tls=77785dec)
[ 7.641042] Stack : 80410000 0000002f 00000000 00000025 000000c0 82e08010 00000000 00030000
00000300 00000400 00010000 8281f7d4 00000000 503f59a2 241cd987 94cb6583
000003e8 42bb9340 00002710 00000018 000003ff 82820000 8386d800 82e08010
99999999 00000001 83971b2c 82e08438 00000001 8281e9fc 83970000 83971ab0
800c2c64 82e08010 00020000 ffffffff 00000220 8281facc 82e08038 82803b44
...
[ 7.675388] Call Trace:
[ 7.677745] [<82803774>] ath9k_hw_wait+0x64/0xb0 [ath9k_hw]
[ 7.683104] [<8281f7d4>] ath9k_hw_setup_statusring+0xe18/0x1df8 [ath9k_hw]
[ 7.689696]
[ 7.691120]
Code: 02202025 0040f809 00000000 <00541024> 10550008 24020001 0c06d836 2404000a 1000fff4
[ 7.700729] ---[ end trace d9df4eff608dc808 ]---
[ 7.706314] Fatal exception: panic in 5 seconds
[ 12.713823] Kernel panic - not syncing: Fatal exception
[ 12.719642] Rebooting in 1 seconds..
€Okazalo sie, ze wystarczylo zmienic adres gdzie wrzucany byl obraz.
Ethernet tez zaczal dzialac
[ 0.000000] Linux version 4.4.92 (bizongod@bizonowo) (gcc version 5.5.0 (LEDE GCC 5.5.0 r5103-f6c4a9c) ) #0 Tue Oct 17 17:43:06 2017
[ 0.000000] MyLoader: sysp=ead62f98, boardp=6d5d0d18, parts=8fe87642
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] No valid device tree found, continuing without
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 804123d0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: mem=64M console=ttyS0,120000 loglevel=7 root=/dev/ram0 rootfstype=ramfs board=SR3200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 58244K/65536K available (2996K kernel code, 144K rwdata, 756K rodata, 2176K init, 200K bss, 7292K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000006] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008203] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.071016] pid_max: default: 32768 minimum: 301
[ 0.075977] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.082951] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092493] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.102902] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.109902] NET: Registered protocol family 16
[ 0.115854] MIPS: machine is YunCore SR3200
[ 0.120406] ar71xx: using random MAC address for eth0
[ 0.342785] clocksource: Switched to clocksource MIPS
[ 0.349215] NET: Registered protocol family 2
[ 0.354450] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.361799] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.368545] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.375334] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.381497] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.388370] NET: Registered protocol family 1
[ 0.393064] PCI: CLS 0 bytes, default 32
[ 2.171224] Crashlog allocated RAM at address 0x3f00000
[ 2.188385] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.194584] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.242451] io scheduler noop registered
[ 2.246632] io scheduler deadline registered (default)
[ 2.252281] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.259347] console [ttyS0] disabled
[ 2.283187] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 2.292277] console [ttyS0] enabled
[ 2.299290] bootconsole [early0] disabled
[ 2.309935] m25p80 spi0.0: found w25q128, expected m25p80
[ 2.315175] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 2.335325] libphy: ag71xx_mdio: probed
[ 2.924567] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII
[ 2.931662] NET: Registered protocol family 10
[ 2.938515] NET: Registered protocol family 17
[ 2.942902] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.955118] 8021q: 802.1Q VLAN Support v1.8
[ 2.972827] Freeing unused kernel memory: 2176K
[ 2.986918] init: Console is alive
[ 2.990350] init: - watchdog -
[ 3.005588] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.022588] usbcore: registered new interface driver usbfs
[ 3.027982] usbcore: registered new interface driver hub
[ 3.033178] usbcore: registered new device driver usb
[ 3.042339] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.049996] ehci-platform: EHCI generic platform driver
[ 3.057241] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.064290] ohci-platform: OHCI generic platform driver
[ 3.069915] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.087239] init: - preinit -
[ 3.217213] eth0: link up (1000Mbps/Full duplex)
[ 6.334233] eth0: link down
[ 6.346018] procd: - early -
[ 6.348861] procd: - watchdog -
[ 6.872892] procd: - watchdog -
[ 6.876112] procd: - ubus -
[ 6.884692] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.929008] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.938028] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.946712] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.955562] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.964223] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.972996] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.981731] random: ubusd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
[ 6.990681] procd: - init -
[ 7.124977] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.134702] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.150325] Loading modules backported from Linux version wt-2017-10-06-0-ga7a22fbbd1f0
[ 7.158047] Backport generated by backports.git v4.14-rc2-1-6-gedfb595c
[ 7.166789] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.178413] nf_conntrack version 0.5.0 (944 buckets, 3776 max)
[ 7.221598] xt_time: kernel timezone is -0000
[ 7.275931] PPP generic driver version 2.4.2
[ 7.282066] NET: Registered protocol family 24
[ 7.317392] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 8.415954] random: jshn: uninitialized urandom read (4 bytes read, 13 bits of entropy available)
[ 8.469797] random: jshn: uninitialized urandom read (4 bytes read, 14 bits of entropy available)
[ 13.832570] eth0: link up (1000Mbps/Full duplex)
[ 13.865287] device eth0.1 entered promiscuous mode
[ 13.869889] device eth0 entered promiscuous mode
[ 13.893367] br-lan: port 1(eth0.1) entered forwarding state
[ 13.898762] br-lan: port 1(eth0.1) entered forwarding state
[ 15.892792] br-lan: port 1(eth0.1) entered forwarding state
root@LEDE:/# ifcofnig
/bin/ash: ifcofnig: not found
root@LEDE:/# ifconfig
br-lan Link encap:Ethernet HWaddr CA:F8:4A:B5:57:08
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fd68:c2aa:484f::1/60 Scope:Global
inet6 addr: fe80::c8f8:4aff:feb5:5708/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1780 (1.7 KiB)
eth0 Link encap:Ethernet HWaddr CA:F8:4A:B5:57:08
inet6 addr: fe80::c8f8:4aff:feb5:5708/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:57 errors:0 dropped:0 overruns:0 frame:0
TX packets:54 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10314 (10.0 KiB) TX bytes:10280 (10.0 KiB)
Interrupt:4
eth0.1 Link encap:Ethernet HWaddr CA:F8:4A:B5:57:08
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1780 (1.7 KiB)
eth0.2 Link encap:Ethernet HWaddr CA:F8:4A:B5:57:08
inet6 addr: fe80::c8f8:4aff:feb5:5708/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:5971 (5.8 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:44 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:2972 (2.9 KiB) TX bytes:2972 (2.9 KiB)
root@LEDE:/# [ 63.332809] random: nonblocking pool is initialized
root@LEDE:/#
root@LEDE:/# ifconfig eth0 192.168.1.121
root@LEDE:/# ifconfig eth0
eth0 Link encap:Ethernet HWaddr CA:F8:4A:B5:57:08
inet addr:192.168.1.121 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::c8f8:4aff:feb5:5708/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:161 errors:0 dropped:0 overruns:0 frame:0
TX packets:73 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:29453 (28.7 KiB) TX bytes:16677 (16.2 KiB)
Interrupt:4
root@LEDE:/# ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
64 bytes from 192.168.1.1: seq=0 ttl=64 time=0.268 ms
64 bytes from 192.168.1.1: seq=1 ttl=64 time=0.226 ms
64 bytes from 192.168.1.1: seq=2 ttl=64 time=0.234 ms
64 bytes from 192.168.1.1: seq=3 ttl=64 time=0.237 ms
64 bytes from 192.168.1.1: seq=4 ttl=64 time=0.224 ms
64 bytes from 192.168.1.1: seq=5 ttl=64 time=0.223 ms
64 bytes from 192.168.1.1: seq=6 ttl=64 time=0.241 ms
64 bytes from 192.168.1.1: seq=7 ttl=64 time=0.224 ms
^C
--- 192.168.1.1 ping statistics ---
8 packets transmitted, 8 packets received, 0% packet loss
round-trip min/avg/max = 0.223/0.234/0.268 ms
root@LEDE:/#Teraz zostaly GPIO, WLAN i ewentualnie sterownik switcha.
GPIO:
- 1 - BTN reset, aktywny niski
- 5 - BTN turbo, aktywny niski
- 6 - LED turbo, aktywny niski
- 21 - LED status, aktywny niski
GPIO dziala
Zostalo radio.
Co ciekawe, art-y sa na offsetach 0x1000 i 0x2000 a nie standardowo 0x5000..
Strony Poprzednia 1 2 3 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → TP-Link WDR7500 v6
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc