Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
A na oryginalnej kości? Programator zweryfikował Ci nową kość bez problemów? Nie uszkodziłeś czegoś na PCB w okolicy miejsca na FLASH?
Strony Poprzednia 1 2
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
RAM DD5116ADTA-6B-E do MR3420 v1 i v2 (Strona 2 z 2)
eko.one.pl → Sprzęt / Hardware → RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Posty: 26 do 33 z 33
- pepe2k
- Użytkownik
- Nieaktywny
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Wziałęm nową i wrzuciłem uboota i dało się normalnie zweryfikować. A tej poprzedniej nie. Oglądałem okolice kości FLASH i wygląda wszystko w porządku, ale jeszcze jutro pod lupą sprawdzę, bo dzisiaj już oczy zmęczone. Pół dnia walczyłem z routerami 
. Spróbuje może jeszcze oryginalną wlutować. Jakby Ci przyszedł jeszcze jakiś pomysł, co może być nie tak będę wdzieczny.
28 2017-10-11 11:33:54 (edytowany przez KevinG 2017-10-11 11:34:27)
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Przejrzałem PCB i wygląda, na to że jest wszystko dobrze. Wlutowałem oryginalną kość 4MB, przez chwilę było niby ok. Zrobiłem update, ale zaraz się posypały błędy..
U-Boot 1.1.4 (Mar 19 2015 - 16:41:32)
U-boot AP123
DRAM: 64 MB
id read 0x100000ff
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0x83ff5188
Fetching MAC Address from 0x83ff5188
wasp reset mask:c03300
WASP ----> S27 PHY
file: ag934x.c,line: 180==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:11:20:00
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth0 up
WASP ----> S27 PHY
file: ag934x.c,line: 180==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:11:20:01
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x50
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x50
eth1 up
eth0, eth1
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.45 (eric@Osiris) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #9 Fri Feb 10 20:43:57 EST 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61204K/65536K available (2425K kernel code, 143K rwdata, 284K rodata, 276K init, 184K bss, 4332K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR3420 v2
[ 0.560000] Switched to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.580000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.590000] TCP: reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.660000] msgmni has been set to 119
[ 0.660000] io scheduler noop registered
[ 0.670000] io scheduler deadline registered (default)
[ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.680000] console [ttyS0] disabled
[ 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.710000] console [ttyS0] enabled
[ 0.710000] console [ttyS0] enabled
[ 0.720000] bootconsole [early0] disabled
[ 0.720000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found gd25q32, expected m25p80
[ 0.740000] m25p80 spi0.0: gd25q32 (4096 Kbytes)
[ 0.740000] 5 tp-link partitions found on MTD device spi0.0
[ 0.750000] Creating 5 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.760000] 0x000000020000-0x000000118f3c : "kernel"
[ 0.760000] 0x000000118f3c-0x0000003f0000 : "rootfs"
[ 0.770000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.780000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.780000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[ 0.790000] 0x0000003f0000-0x000000400000 : "art"
[ 0.800000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.820000] libphy: ag71xx_mdio: probed
[ 1.420000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 1.430000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.020000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.060000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.070000] TCP: cubic registered
[ 2.070000] NET: Registered protocol family 17
[ 2.080000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.090000] Bridge firewalling registered
[ 2.090000] 8021q: 802.1Q VLAN Support v1.8
[ 2.110000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.120000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
[ 3.200000] init: Console is alive
[ 3.210000] init: - watchdog -
[ 5.260000] init: - preinit -
[ 5.900000] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.480000] eth1: link up (1000Mbps/Full duplex)
[ 9.230000] jffs2: notice: (333) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.250000] mount_root: switching to jffs2 overlay
[ 9.290000] eth1: link down
[ 9.310000] procd: - early -
[ 9.310000] procd: - watchdog -
[ 10.100000] procd: - ubus -
[ 11.110000] procd: - init -
Please press Enter to activate this console.
[ 12.260000] tun: Universal TUN/TAP device driver, 1.6
[ 12.270000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.280000] gre: GRE over IPv4 demultiplexor driver
[ 12.280000] ip_gre: GRE over IPv4 tunneling driver
[ 12.310000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 12.320000] Hooked IMQ after mangle on PREROUTING
[ 12.330000] Hooked IMQ after nat on POSTROUTING
[ 12.330000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1, imq_dev_accurate_stats = 1)
[ 12.340000] Hooking IMQ before NAT on PREROUTING.
[ 12.350000] Hooking IMQ after NAT on POSTROUTING.
[ 12.370000] u32 classifier
[ 12.380000] input device check on
[ 12.380000] Actions configured
[ 12.380000] Mirror/redirect action on
[ 12.450000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 12.460000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 12.500000] Ebtables v2.0 registered
[ 12.510000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.600000] Netfilter messages via NETLINK v0.30.
[ 12.720000] xt_time: kernel timezone is -0000
[ 12.870000] PPP generic driver version 2.4.2
[ 12.880000] PPP MPPE Compression module registered
[ 12.890000] NET: Registered protocol family 24
[ 12.890000] PPTP driver version 0.8.5
[ 13.010000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[ 21.770000] device eth1 entered promiscuous mode
[ 23.970000] eth0: link up (100Mbps/Full duplex)
[ 24.180000] device wlan0 entered promiscuous mode
[ 24.180000] br-lan: port 2(wlan0) entered forwarding state
[ 24.190000] br-lan: port 2(wlan0) entered forwarding state
[ 24.480000] eth1: link up (1000Mbps/Full duplex)
[ 24.480000] br-lan: port 1(eth1) entered forwarding state
[ 24.490000] br-lan: port 1(eth1) entered forwarding state
[ 24.970000] br-lan: port 2(wlan0) entered disabled state
[ 25.510000] br-lan: port 2(wlan0) entered forwarding state
[ 25.510000] br-lan: port 2(wlan0) entered forwarding state
[ 26.490000] br-lan: port 1(eth1) entered forwarding state
[ 27.510000] br-lan: port 2(wlan0) entered forwarding state
BusyBox v1.23.2 (2017-02-09 15:24:42 EST) built-in shell (ash)
------------------------------------------------------------------
| _____ _ |
| | __ \ | | |
| | | \/ __ _ _ __ __ _ ___ _ _| | ___ |
| | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \ |
| | |_\ \ (_| | | | (_| | (_) | |_| | | __/ |
| \____/\__,_|_| \__, |\___/ \__, |_|\___| |
| __/ | __/ | |
| |___/ |___/ |
| |
|----------------------------------------------------------------|
| Gargoyle version 1.9.2 | OpenWrt Chaos Calmer branch |
| Gargoyle revision ecc1da74| OpenWrt commit 03d52cf |
| Built February 10, 2017 | Target ar71xx/default |
------------------------------------------------------------------
root@Gargoyle:/# [ 49.320000] random: nonblocking pool is initialized
root@Gargoyle:/# [ 68.980000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
[ 68.990000] old minutes west=0, new minutes west=-60
[ 76.000000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 00000000
[ 76.000000] Oops[#1]:
[ 76.000000] CPU: 0 PID: 2199 Comm: hotplug-call Not tainted 3.18.45 #9
[ 76.000000] task: 82d0dd10 ti: 82d02000 task.ti: 82d02000
[ 76.000000] $ 0 : 00000000 80370000 838289b0 00000000
[ 76.000000] $ 4 : 838289b0 82d0dd10 1100f400 ffff00fe
[ 76.000000] $ 8 : 82d03fe0 0000f400 00000000 ffffff80
[ 76.000000] $12 : 7ff36248 00000000 00000174 00000000
[ 76.000000] $16 : 83b97070 838289b0 8030d290 802d0000
[ 76.000000] $20 : 00000000 80310000 8030d290 83992c00
[ 76.000000] $24 : 00000001 8009bd40
[ 76.000000] $28 : 82d02000 82d03f28 83b971fc 00000000
[ 76.000000] Hi : 00000011
[ 76.000000] Lo : b1f3f800
[ 76.000000] epc : 00000000 (null)
[ 76.000000] Not tainted
[ 76.000000] ra : 00000000 (null)
[ 76.000000] Status: 1100f402 KERNEL EXL
[ 76.000000] Cause : 00800008
[ 76.000000] BadVA : 00000000
[ 76.000000] PrId : 0001974c (MIPS 74Kc)
[ 76.000000] Modules linked in: ath9k ath9k_common pppoe ppp_async iptable_nat ath9k_hw ath pptp pppox ppp_mppe ppp_generic nf_nat_pptp nf_nat_ipv4 nf_nat_amanda nf_conntrack_pptp nf_conntrack_ipv4 nf_conntrack_amanda mac80211 ipt_REJECT ipt_MASQUERADE ebtable_nat ebtable_filter ebtable_broute cfg80211 xt_time xt_tcpudp xt_tcpmss xt_string xt_statistic xt_state xt_recent xt_quota xt_pkttype xt_physdev xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_iprange xt_id xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_NETMAP xt_LOG xt_HL xt_DSCP xt_CT xt_CLASSIFY ts_kmp ts_fsm ts_bm slhc nfnetlink nf_reject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_proto_gre nf_nat_masquerade_ipv4 nf_nat_irc nf_nat_h323 nf_nat_ftp nf_nat nf_log_ipv4 nf_log_common nf_defrag_ipv4 nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip nf_conntrack_rtcache nf_conntrack_proto_gre nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp nf_conntrack_broadcast iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables ebtables ebt_vlan ebt_stp ebt_snat ebt_redirect ebt_pkttype ebt_mark_m ebt_mark ebt_limit ebt_ip ebt_dnat ebt_arpreply ebt_arpnat ebt_arp ebt_among ebt_802_3 crc_ccitt compat em_nbyte sch_teql sch_htb sch_prio act_ipt sch_gred sch_dsmark cls_basic sch_codel em_text em_meta act_police sch_pie sch_tbf sch_sfq sch_fq em_cmp sch_red act_skbedit act_mirred em_u32 cls_u32 cls_tcindex cls_flow cls_route cls_fw sch_hfsc sch_ingress xt_IMQ imq ipt_weburl ipt_webmon ipt_timerange ipt_layer7 nf_conntrack ipt_bandwidth x_tables ip_gre gre ip_tunnel tun sha1_generic ecb arc4 crypto_blkcipher gpio_button_hotplug aead crypto_hash
[ 76.000000] Process hotplug-call (pid: 2199, threadinfo=82d02000, task=82d0dd10, tls=77fe4440)
[ 76.000000] Stack : 00000012 00000000 7fa8c890 00000001 77fdd068 77f23144 33302d68 6f73746e
00000000 00000001 00000000 77fe4440 01200012 00000000 00000000 00000000
00000000 6d696e63 82d22460 00000013 0000000e 00000007 00000001 802ecb80
00000000 77f55ff4 77fdd000 00000000 7fa8caf0 00000000 00000000 00000000
004584e4 77f3bb80 00000000 00000000 77f5c3a0 7ff36238 7ff36258 004197b3
...
[ 76.000000] Call Trace:
[ 76.000000]
Code: (Bad address in epc)
[ 76.000000]
[ 76.310000] ---[ end trace 221be650cd08274e ]---
root@Gargoyle:/#
root@Gargoyle:/#
root@Gargoyle:/#
root@Gargoyle:/#
root@Gargoyle:/#
root@Gargoyle:/#
root@Gargoyle:/# reboot
root@Gargoyle:/# [ 158.440000] br-lan: port 2(wlan0) entered disabled state
[ 158.440000] br-lan: port 1(eth1) entered disabled state
[ 158.450000] device eth1 left promiscuous mode
[ 158.450000] br-lan: port 1(eth1) entered disabled state
[ 158.500000] eth1: link down
[ 158.500000] device wlan0 left promiscuous mode
[ 158.500000] br-lan: port 2(wlan0) entered disabled state
[ 158.820000] eth0: link down
[ 162.820000] Removing MTD device #3 (rootfs_data) with use count 1
[ 162.840000] reboot: Restarting system
U-Boot 1.1.4 (Mar 19 2015 - 16:41:32)
U-boot AP123
DRAM: 64 MB
id read 0x100000ff
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0x83ff5188
Fetching MAC Address from 0x83ff5188
wasp reset mask:c03300
WASP ----> S27 PHY
file: ag934x.c,line: 180==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:11:20:00
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth0 up
WASP ----> S27 PHY
file: ag934x.c,line: 180==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:11:20:01
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x50
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x50
eth1 up
eth0, eth1
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.45 (eric@Osiris) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #9 Fri Feb 10 20:43:57 EST 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61204K/65536K available (2425K kernel code, 143K rwdata, 284K rodata, 276K init, 184K bss, 4332K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR3420 v2
[ 0.560000] Switched to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.580000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.590000] TCP: reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.650000] msgmni has been set to 119
[ 0.650000] io scheduler noop registered
[ 0.660000] io scheduler deadline registered (default)
[ 0.660000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.670000] console [ttyS0] disabled
� 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.700000] console [ttyS0] enabled
[ 0.700000] console [ttyS0] enabled
[ 0.710000] bootconsole [early0] disabled
[ 0.710000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found gd25q32, expected m25p80
[ 0.740000] m25p80 spi0.0: gd25q32 (4096 Kbytes)
[ 0.740000] 5 tp-link partitions found on MTD device spi0.0
[ 0.750000] Creating 5 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.760000] 0x000000020000-0x000000118f3c : "kernel"
[ 0.770000] 0x000000118f3c-0x0000003f0000 : "rootfs"
[ 0.770000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.780000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.780000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[ 0.790000] 0x0000003f0000-0x000000400000 : "art"
[ 0.800000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.820000] libphy: ag71xx_mdio: probed
[ 1.420000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 1.430000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.020000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.060000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.070000] TCP: cubic registered
[ 2.070000] NET: Registered protocol family 17
[ 2.080000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.090000] Bridge firewalling registered
[ 2.090000] 8021q: 802.1Q VLAN Support v1.8
[ 2.110000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.120000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
[ 3.200000] init: Console is alive
[ 3.210000] init: - watchdog -
[ 5.260000] init: - preinit -
[ 5.900000] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.480000] eth1: link up (1000Mbps/Full duplex)
[ 9.230000] jffs2: notice: (333) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.250000] mount_root: switching to jffs2 overlay
[ 9.290000] eth1: link down
[ 9.310000] procd: - early -
[ 9.310000] procd: - watchdog -
[ 10.090000] procd: - ubus -
[ 11.110000] procd: - init -
Please press Enter to activate this console.
[ 12.260000] tun: Universal TUN/TAP device driver, 1.6
[ 12.270000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.280000] gre: GRE over IPv4 demultiplexor driver
[ 12.290000] ip_gre: GRE over IPv4 tunneling driver
[ 12.300000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 12.330000] Hooked IMQ after mangle on PREROUTING
[ 12.330000] Hooked IMQ after nat on POSTROUTING
[ 12.340000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1, imq_dev_accurate_stats = 1)
[ 12.350000] Hooking IMQ before NAT on PREROUTING.
[ 12.350000] Hooking IMQ after NAT on POSTROUTING.
[ 12.380000] u32 classifier
[ 12.380000] input device check on
[ 12.380000] Actions configured
[ 12.390000] Mirror/redirect action on
[ 12.450000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 12.460000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 12.490000] Ebtables v2.0 registered
[ 12.500000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.590000] Netfilter messages via NETLINK v0.30.
[ 12.690000] xt_time: kernel timezone is -0000
[ 12.830000] PPP generic driver version 2.4.2
[ 12.840000] PPP MPPE Compression module registered
[ 12.850000] NET: Registered protocol family 24
[ 12.850000] PPTP driver version 0.8.5
[ 13.000000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[ 18.180000] CPU 0 Unable to handle kernel paging request at virtual address e043012c, epc == 8007500c, ra == 80060820
[ 18.190000] CPU 0 Unable to handle kernel paging request at virtual address 756179d0, epc == 8009aefc, ra == 800a95b4
[ 18.190000] Oops[#1]:
[ 18.190000] CPU: 0 PID: 1634607169 Comm: Not tainted 3.18.45 #9
[ 18.190000] task: 8fa20060 ti: 800e8000 task.ti: 65000000
[ 18.190000] $ 0 : 00000000 00000001 8030d210 75617900
[ 18.190000] $ 4 : 8fa20060 65726e20 00000001 65726e21
[ 18.190000] $ 8 : 00000004 3c040004 00040000 38e92e55
[ 18.190000] $12 : 00000000 00000000 00000000 5caa9c68
[ 18.190000] $16 : 8fa20060 00000000 3cbfdf23 80390000
[ 18.190000] $20 : 80390000 00000004 8030d8d0 800e9c94
[ 18.190000] $24 : 00000000 801c1804
[ 18.190000] $28 : 800e8000 800e9b14 00989680 800a95b4
[ 18.190000] Hi : 00000004
[ 18.190000] Lo : 30e23400
[ 18.190000] epc : 8009aefc 0x8009aefc
[ 18.190000] Not tainted
[ 18.190000] ra : 800a95b4 0x800a95b4
[ 18.190000] Status: 11007402 KERNEL EXL
[ 18.190000] Cause : 00800008
[ 18.190000] BadVA : 756179d0
[ 18.190000] PrId : 0001974c (MIPS 74Kc)
[ 18.190000] Modules linked in: ath9k ath9k_common pppoe ppp_async iptable_nat ath9k_hw ath pptp pppox ppp_mppe ppp_generic nf_nat_pptp nf_nat_ipv4 nf_nat_amanda nf_conntrack_pptp nf_conntrack_ipv4 nf_conntrack_amanda mac80211 ipt_REJECT ipt_MASQUERADE ebtable_nat ebtable_filter ebtable_broute cfg80211 xt_time xt_tcpudp xt_tcpmss xt_string xt_statistic xt_state xt_recent xt_quota xt_pkttype xt_physdev xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_iprange xt_id xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_NETMAP xt_LOG xt_HL xt_DSCP xt_CT xt_CLASSIFY ts_kmp ts_fsm ts_bm slhc nfnetlink nf_reject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_proto_gre nf_nat_masquerade_ipv4 nf_nat_irc nf_nat_h323 nf_nat_ftp nf_nat nf_log_ipv4 nf_log_common nf_defrag_ipv4 nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip nf_conntrack_rtcache nf_conntrack_proto_gre nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp nf_conntrack_broadcast iptable_raw iptable_mangle iptable_filter ipt_ECN ip_tables ebtables ebt_vlan ebt_stp ebt_snat ebt_redirect ebt_pkttype ebt_mark_m ebt_mark ebt_limit ebt_ip ebt_dnat ebt_arpreply ebt_arpnat ebt_arp ebt_among ebt_802_3 crc_ccitt compat em_nbyte sch_teql sch_htb sch_prio act_ipt sch_gred sch_dsmark cls_basic sch_codel em_text em_meta act_police sch_pie sch_tbf sch_sfq sch_fq em_cmp sch_red act_skbedit act_mirred em_u32 cls_u32 cls_tcindex cls_flow cls_route cls_fw sch_hfsc sch_ingress xt_IMQ imq ipt_weburl ipt_webmon ipt_timerange ipt_layer7 nf_conntrack ipt_bandwidth x_tables ip_gre gre ip_tunnel tun sha1_generic ecb arc4 crypto_blkcipher gpio_button_hotplug aead crypto_hash
[ 18.190000] Process (pid: 1634607169, threadinfo=800e8000, task=8fa20060, tls=02242021)
[ 18.190000] Stack : 3cbfdf23 80390000 80390000 00000004 8030d8d0 80390000 00000000 800b5aac
[ 18.190000] 00008821 24420001 ae020014 8e040000 8030d708 8030d8d0 00000004 3cbfdf23
[ 18.190000] 8030d8d0 8030d708 8030d6d0 7fffffff 00000004 ffffffff 00000000 00000003
[ 18.190000] 3cbfc4e9 800aa034 80310000 80310000 00000079 80310000 80310000 8030d6d0
[ 18.190000] 3cbfc4e9 800aa5f0 2402fff4 8fbf0024 8fb30020 8fb2001c 00000004 3cbfc4e9
[ 18.190000] ...
[ 18.190000] Call Trace:[<800b5aac>] 0x800b5aac
[ 18.190000] [<800aa034>] 0x800aa034
[ 18.190000] [<800aa5f0>] 0x800aa5f0
[ 18.190000] [<800730f8>] 0x800730f8
[ 18.190000] [<800a3c24>] 0x800a3c24
[ 18.190000] [<800a6098>] 0x800a6098
[ 18.190000] [<800e9ce4>] 0x800e9ce4
[ 18.190000] [<800a35f4>] 0x800a35f4
[ 18.190000] [<8006deb4>] 0x8006deb4
[ 18.190000] [<80060830>] 0x80060830
[ 18.190000] [<801c2290>] 0x801c2290
[ 18.190000] [<801c22b0>] 0x801c22b0
[ 18.190000] [<801c2290>] 0x801c2290
[ 18.190000] [<801c1804>] 0x801c1804
[ 18.190000] [<800a13e4>] 0x800a13e4
[ 18.190000] [<800e8000>] 0x800e8000
[ 18.190000] [<800e9d4c>] 0x800e9d4c
[ 18.190000] [<800a1cdc>] 0x800a1cdc
[ 18.190000] [<800a1ce8>] 0x800a1ce8
[ 18.190000] [<800a1624>] 0x800a1624
[ 18.190000] [<800a232c>] 0x800a232c
[ 18.190000] [<800e9ef4>] 0x800e9ef4
[ 18.190000] [<80060820>] 0x80060820
[ 18.190000] [<800a2524>] 0x800a2524
[ 18.190000] [<800e9ef4>] 0x800e9ef4
[ 18.190000] [<80074f88>] 0x80074f88
[ 18.190000] [<800e9e30>] 0x800e9e30
[ 18.190000] [<800e9e30>] 0x800e9e30
[ 18.190000] [<80075264>] 0x80075264
[ 18.190000] [<8007500c>] 0x8007500c
[ 18.190000] [<80060820>] 0x80060820
[ 18.190000] [<800ea074>] 0x800ea074
[ 18.190000] [<80060820>] 0x80060820
[ 18.190000] [<80060820>] 0x80060820
[ 18.190000] [<800ea074>] 0x800ea074
[ 18.190000] [<800ea074>] 0x800ea074
[ 18.190000] [<80060820>] 0x80060820
[ 18.190000] [<800ea000>] 0x800ea000
[ 18.190000] [<800e9fac>] 0x800e9fac
[ 18.190000] [<80060820>] 0x80060820
[ 18.190000] [<8007500c>] 0x8007500c
[ 18.190000]
[ 18.190000]
[ 18.190000] Code: 8c8501e8 00a73821 ac8701e8 <8c6500d0> 10a00004 00000000 8c840400 14800010 00000000
[ 18.190000] ---[ end trace 91eb745b91eb745b ]---
[ 18.190000] Kernel panic - not syncing: Fatal exception in interrupt
[ 18.190000] Rebooting in 3 seconds..
U-Boot 1.1.4 (Mar 19 2015 - 16:41:32)
U-boot AP123
DRAM: 64 MB
id read 0x100000ff
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0x83ff5188
Fetching MAC Address from 0x83ff5188
wasp reset mask:c03300
WASP ----> S27 PHY
file: ag934x.c,line: 180==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:11:20:00
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth0 up
WASP ----> S27 PHY
file: ag934x.c,line: 180==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:11:20:01
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x50
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x50
eth1 up
eth0, eth1
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.45 (eric@Osiris) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #9 Fri Feb 10 20:43:57 EST 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61204K/65536K available (2425K kernel code, 143K rwdata, 284K rodata, 276K init, 184K bss, 4332K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR3420 v2
[ 0.560000] Switched to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.580000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.590000] TCP: reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.650000] msgmni has been set to 119
[ 0.650000] io scheduler noop registered
[ 0.660000] io scheduler deadline registered (default)
[ 0.660000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.670000] console [ttyS0] disabled
� 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.700000] console [ttyS0] enabled
[ 0.700000] console [ttyS0] enabled
[ 0.710000] bootconsole [early0] disabled
[ 0.710000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found gd25q32, expected m25p80
[ 0.740000] m25p80 spi0.0: gd25q32 (4096 Kbytes)
[ 0.740000] 5 tp-link partitions found on MTD device spi0.0
[ 0.750000] Creating 5 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.760000] 0x000000020000-0x000000118f3c : "kernel"
[ 0.760000] 0x000000118f3c-0x0000003f0000 : "rootfs"
[ 0.770000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.780000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.790000] 0x000000380000-0x0000003f0000 : "rootfs_data"
[ 0.790000] 0x0000003f0000-0x000000400000 : "art"
[ 0.800000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.820000] libphy: ag71xx_mdio: probed
[ 1.420000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 1.430000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.020000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.060000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.070000] TCP: cubic registered
[ 2.070000] NET: Registered protocol family 17
[ 2.080000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.090000] Bridge firewalling registered
[ 2.090000] 8021q: 802.1Q VLAN Support v1.8
[ 2.110000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.120000] Freeing unused kernel memory: 276K (8032b000 - 80370000)
[ 3.200000] init: Console is alive
[ 3.210000] init: - watchdog -
[ 5.260000] init: - preinit -
[ 5.900000] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.480000] eth1: link up (1000Mbps/Full duplex)
[ 9.250000] jffs2: notice: (334) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.270000] mount_root: switching to jffs2 overlay
[ 9.310000] eth1: link down
[ 9.320000] procd: - early -
[ 9.330000] procd: - watchdog -
[ 10.110000] procd: - ubus -
[ 11.130000] procd: - init -
Please press Enter to activate this console.
[ 12.280000] tun: Universal TUN/TAP device driver, 1.6
[ 12.280000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.290000] gre: GRE over IPv4 demultiplexor driver
[ 12.300000] ip_gre: GRE over IPv4 tunneling driver
[ 12.320000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 12.340000] Hooked IMQ after mangle on PREROUTING
[ 12.340000] Hooked IMQ after nat on POSTROUTING
[ 12.350000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1, imq_dev_accurate_stats = 1)
[ 12.360000] Hooking IMQ before NAT on PREROUTING.
[ 12.360000] Hooking IMQ after NAT on POSTROUTING.
[ 12.400000] u32 classifier
[ 12.400000] input device check on
[ 12.410000] Actions configured
[ 12.410000] Mirror/redirect action on
[ 12.480000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 12.490000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 12.540000] Ebtables v2.0 registered
[ 12.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.650000] Netfilter messages via NETLINK v0.30.
[ 12.760000] xt_time: kernel timezone is -0000
[ 12.960000] PPP generic driver version 2.4.2
[ 12.970000] PPP MPPE Compression module registered
[ 12.980000] NET: Registered protocol family 24
[ 12.980000] PPTP driver version 0.8.5
[ 13.100000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
[ 22.040000] device eth1 entered promiscuous mode
[ 24.320000] device wlan0 entered promiscuous mode
[ 24.660000] eth1: link up (1000Mbps/Full duplex)
[ 24.690000] br-lan: port 1(eth1) entered forwarding state
[ 24.690000] br-lan: port 1(eth1) entered forwarding state
[ 25.150000] eth0: link up (100Mbps/Full duplex)
[ 25.630000] br-lan: port 2(wlan0) entered forwarding state
[ 25.630000] br-lan: port 2(wlan0) entered forwarding state
[ 26.690000] br-lan: port 1(eth1) entered forwarding state
[ 27.630000] br-lan: port 2(wlan0) entered forwarding state
BusyBox v1.23.2 (2017-02-09 15:24:42 EST) built-in shell (ash)
------------------------------------------------------------------
| _____ _ |
| | __ \ | | |
| | | \/ __ _ _ __ __ _ ___ _ _| | ___ |
| | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \ |
| | |_\ \ (_| | | | (_| | (_) | |_| | | __/ |
| \____/\__,_|_| \__, |\___/ \__, |_|\___| |
| __/ | __/ | |
| |___/ |___/ |
| |
|----------------------------------------------------------------|
| Gargoyle version 1.9.2 | OpenWrt Chaos Calmer branch |
| Gargoyle revision ecc1da74| OpenWrt commit 03d52cf |
| Built February 10, 2017 | Target ar71xx/default |
------------------------------------------------------------------
root@Gargoyle:/# [ 52.390000] random: nonblocking pool is initialized
[ 69.240000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
[ 69.250000] old minutes west=0, new minutes west=-60- pepe2k
- Użytkownik
- Nieaktywny
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Według dokumentacji, ta kość to DDR333 i może dlatego się wywala. Ewentualnie coś poszło nie tak przy montażu. Skoro wykłada się nawet z fabrycznym U-Boot, to już poważna sprawa.
Możesz spróbować zmniejszyć zegary w moim U-Boot (polecenie "setclk"), znaleźć odpowiednią kość (DDR400) albo zacząć przyzwyczajać się do nowego przycisku do papieru.
30 2017-10-11 12:02:47 (edytowany przez KevinG 2017-10-11 12:05:32)
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Teraz niby jest ok, ale pewnie nie na długo.. Dobra wylutowuje kość, wlutowuje 16MB z Twoim ubootem i pobawie się zegarami. Da się programować flash klipsem nieodlutowując go? Jak zakładam klips i podłączam programator do USB to włącza mi się router i nie wiem czy tak może być.
- pepe2k
- Użytkownik
- Nieaktywny
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
KevinG napisał/a:
Da się programować flash klipsem nieodlutowując go? Jak zakładam klips i podłączam programator do USB to włącza mi się router i nie wiem czy tak może być.
Nie na tej platformie... i uważaj, bo możesz tak coś uszkodzić (zasilasz router ze swojego adaptera przez interfejs SPI).
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Chyba się udało Zmieniłem poprzez setclk RAM na 300MHz, przy okazji dałem radiator na procesor i podkręciłem go do 600MHz. Podniesienie zegara procka o 50MHz jest w miarę bezpieczne? Narazie zachowuje się dobrze. Zainstalowałem luci lede i zaraz dodam jeszcze vpna i trochę go pomęcze. Mam nadzieję, że wyjdzie z tego cały 
. Fajny ten nowy u-boot.
- pepe2k
- Użytkownik
- Nieaktywny
Odp: RAM DD5116ADTA-6B-E do MR3420 v1 i v2
KevinG napisał/a:
Chyba się udało
Dzięki
50 MHz nie powinno robić mu żadnej różnicy.
Posty: 26 do 33 z 33
Strony Poprzednia 1 2
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → RAM DD5116ADTA-6B-E do MR3420 v1 i v2
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc