Obie konsole szeregowe działają, trzeba oczywiście uzupełnić brakujące zworki.
J2 - konsola routera (QCA9531, 115200 8n1):
1 - VCC (3V3)
2 - GND
3 - RX
4 - TX
Dostęp do systemu: root/sohoadmin
Log:
U-Boot 1.1.4-g23c7cce0-dirty (Build from LSDK- at Mar 22 2016 - 09:14:13)
ap143 - Honey Bee 2.0
DRAM: 64 MB
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
eth0 up
Honey Bee ----> MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x60c1a100
is_auto_upload_firmware=0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
Booting QCA953x
Linux version 2.6.31 (tp-link@Sohoidev) (gcc version 4.3.3 (GCC) ) #1 Tue Mar 22 09:16:59 CST 2016
flash_size passed from bootloader = 8
Ram size passed from bootloader =67108864
CPU revision is: 00019374 (MIPS 24Kc)
ath_sys_frequency: cpu apb ddr apb cpu 650 ddr 390 ahb 216
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 56408k/65536k available (1715k kernel code, 9052k reserved, 417k data, 112k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 433.15 BogoMIPS (lpj=866304)
Mount-cache hash table entries: 512
****************ALLOC***********************
Packet mem: 80243720 (0x600000 bytes)
********************************************
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
net_link: create socket ok.
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 110
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000007e0000 : "rootfs"
0x0000007e0000-0x0000007f0000 : "config"
0x0000007f0000-0x000000800000 : "art"
->Oops: flash id 0xef4017 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed
init started: BusyBox v1.01 (2016.03.22-01:21+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (1024 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/af_key.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xfrm_user.ko': No such file or directory
(none) mips #1 Tue Mar 22 09:16:59 CST 2016 (none)
(none) login: Now flash open!
Now flash open!
vlan init params sucess.
qca955x_GMAC: Length per segment 1536
953x_GMAC: qca953x_gmac_attach
Link Int Enabled
qca953x_set_gmac_caps CHECK DMA STATUS
mac:1 Registering S27....
qca955x_GMAC: RX TASKLET - Pkts per Intr:18
qca955x_GMAC: Max segments per packet : 1
qca955x_GMAC: Max tx descriptor count : 511
qca955x_GMAC: Max rx descriptor count : 128
qca955x_GMAC: Mac capability flags : 2D81
953x_GMAC: qca953x_gmac_attach
Link Int Enabled
qca953x_set_gmac_caps CHECK DMA STATUS
mac:0 Registering S27....
qca955x_GMAC: RX TASKLET - Pkts per Intr:18
qca955x_GMAC: Max segments per packet : 1
qca955x_GMAC: Max tx descriptor count : 511
qca955x_GMAC: Max rx descriptor count : 128
qca955x_GMAC: Mac capability flags : 2581
athr_gmac_ring_alloc Allocated 8176 at 0x83868000
athr_gmac_ring_alloc Allocated 2048 at 0x838d1000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_alloc Allocated 8176 at 0x8385a000
athr_gmac_ring_alloc Allocated 2048 at 0x83bd1800
HONEYBEE ----> S27 PHY MDIO
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0 entered promiscuous mode
athr_gmac_ring_free Freeing at 0x83868000
athr_gmac_ring_free Freeing at 0x838d1000
athr_gmac_ring_alloc Allocated 8176 at 0x838ec000
athr_gmac_ring_alloc Allocated 2048 at 0x838d1000
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
Now flash open!
athr_gmac_ring_free Freeing at 0x8385a000
athr_gmac_ring_free Freeing at 0x83bd1800
athr_gmac_ring_alloc Allocated 8176 at 0x83844000
athr_gmac_ring_alloc Allocated 2048 at 0x83bd1800
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
usb 1-1: new high speed USB device using ath-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
Now flash open!
adf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 10.2-00082-4 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
Enterprise mode: 0x03fc0000
Restoring Cal data from Flash
ath_get_caps[6174] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[6149] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros ???: mem=0xb8100000, irq=2
ath_pci: 10.2-00082-4 (Atheros/multi-bss)
LTE_COEX: lteWifiCoexInit, init struct lte_coex
VAP device ath0 created
DES SSID SET=TP-LINK_7518
Set freq vap stop send + 83108000
Set freq vap stop send -83108000
Set wait done --83108000
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
Setting Max Stations:32
DCS for CW interference mitigation: 0
DCS for WLAN interference mitigation: 0
DES SSID SET=TP-LINK_7518
LTE_COEX: lteWifiRandomChannel, lte_coex.acs_chan_mask is 0! no need to change channel!
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
Set freq vap stop send + 83108000
Set freq vap stop send -83108000
Set wait done --83108000
Set freq vap stop send + 83108000
Set freq vap stop send -83108000
Set wait done --83108000
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
Scan in progress.. Cancelling it
athr_gmac_ring_free Freeing at 0x83844000
athr_gmac_ring_free Freeing at 0x83bd1800
br0: port 1(eth0) entering disabled state
athr_gmac_ring_alloc Allocated 8176 at 0x83868000
athr_gmac_ring_alloc Allocated 2048 at 0x83bd1800
HONEYBEE ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=393856, new mode=3, valid=1
Scan in progress.. Cancelling it
br0: port 2(ath0) entering disabled state
DES SSID SET=TP-LINK_7518
br0: port 2(ath0) entering forwarding state
mlme_create_infra_bss : Overriding HT40 channel with HT20 channel
(all_group_send_igmp_leave)809, has delete all IGMP groups and timer
NET: Registered protocol family 10
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
IPv6 over IPv4 tunneling driver
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
device eth1 entered promiscuous mode
fastnat init
lte0: IPv6 duplicate address detected!
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbserial_generic 1-1:1.2: generic converter detected
usb 1-1: generic converter now attached to ttyUSB0
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
option 1-1:1.4: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
option 1-1:1.5: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
usbcore: registered new interface driver option
option_2: v0.7.2:USB Driver for GSM modems
LTE_COEX: Bandinfo unknown error
qca955x_GMAC: GE0 RX DMA ENABLE
blockWps_proc_write 868: write value = 0
Lte net info change!
TL-MR6400 mips #1 Tue Mar 22 09:16:59 CST 2016 (none)
TL-MR6400 login: root
Password:
Jan 1 00:03:58 login[210]: root login on `ttyS0'
BusyBox v1.01 (2016.03.22-01:21+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
# cat /proc/cpuinfo
system type: QCA953x
processor: 0
cpu model: MIPS 24Kc V7.4
BogoMIPS: 433.15
wait instruction: yes
microsecond timers: yes
tlb_entries: 16
extra interrupt vector: yes
hardware watchpoint: yes, count: 4, address/irw mask: [0x0004, 0x0a10, 0x06d8, 0x0ff8]
ASEs implemented: mips16
shadow register sets: 1
core: 0
VCED exceptions: not available
VCEI exceptions: not available
# ls / -la
drwxrwxr-x 15 0 0 200 Mar 22 2016 .
drwxrwxr-x 15 0 0 200 Mar 22 2016 ..
drwxr-xr-x 2 0 0 300 Mar 22 2016 bin
drwxrwxr-x 3 0 0 1042 Mar 22 2016 dev
drwxrwxr-x 6 0 0 311 Mar 22 2016 etc
drwxrwxr-x 5 0 0 1217 Mar 22 2016 lib
lrwxrwxrwx 1 0 0 11 Mar 22 2016 linuxrc -> bin/busybox
drwxrwxr-x 2 0 0 3 Mar 22 2016 mnt
dr-xr-xr-x 61 0 0 0 Jan 1 1970 proc
drwxrwxr-x 2 0 0 3 Mar 22 2016 root
drwxrwxr-x 2 0 0 400 Mar 22 2016 sbin
drwxrwxr-x 2 0 0 3 Mar 22 2016 sys
drwxr-xr-x 6 0 0 0 Jan 1 00:00 tmp
drwxrwxr-x 4 0 0 66 Mar 22 2016 usr
drwxr-xr-x 3 0 0 0 Jan 1 00:00 var
drwxrwxr-x 10 0 0 141 Mar 22 2016 web
# cat /proc/cmdline
console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),6912k(rootfs),64k(config),64k(art) mem=32M
# cat /proc/mtd
dev: size erasesize name
mtd0: 00020000 00010000 "u-boot"
mtd1: 00100000 00010000 "kernel"
mtd2: 006c0000 00010000 "rootfs"
mtd3: 00010000 00010000 "config"
mtd4: 00010000 00010000 "art"
#
\[ getty logger scp
arping hostapd login sh
bpalogin hostname logread sleep
brctl httpd ls snmpd
busybox ifconfig lsmod syslogd
cat init mknod tc
chmod insmod mount tddpd
date ip msh test
dbclient iptables npd6 tftp
df iptables-multi ping tpatd
dhcp6c iptables-restore ping6 true
dhcp6ctl iptables-save pppd udhcpc
dhcp6s iwconfig ps udhcpd
dropbear iwlist radvd umount
dropbearconvert iwpriv radvdctl vconfig
dropbearkey kill reboot wlanconfig
dropbearmulti klogd rm wpa_supplicant
echo lld2d rmmod xl2tpd
false ln route
J12 - konsola modemu (Qualcomm MSM 9625, 115200 8n1, uwaga: logika 1V8):
1 - VCC (3V3)
2 - GND
3 - RX
4 - TX
Dostęp do systemu: brak danych (na razie 
)
Log:
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk
[10] platform_init()
[10] target_init()
[10] smem ptable found: ver: 4 len: 19
[30] USB init ept @ 0x7e2a000
[50] Invalid partition index
[50] Invalid partition index
[50] Invalid partition index
[50] fastboot_init()
[50] udc_start()
[60] Wait for fastboot command
[2060] Loading boot image (3545088): start
[2680] Loading boot image (3545088): done
[2700] cmdline: noinitrd root=/dev/mtdblock17 rw rootfstype=yaffs2 console=ttyHSL0,115200,n8 androidboot.hardware=qcom ehci-hcd.park=3 g-android.rx_trigger_enabled=1 androidboot.serialno=MDM9625 androidboot.baseband=msm
[2720] Updating device tree: start
[2770] Updating device tree: done
[2770] booting linux @ 0x308000, ramdisk @ 0x308000 (0), tags/device tree @ 0x6800000
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.0+ (tp-link@Sohoidev) (gcc version 4.6.3 20111117 (prerelease) (GCC) ) #1 PREEMPT Wed Oct 15 10:58:56 CST 2014
[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Qualcomm MSM 9625 (Flattened Device Tree), model: Qualcomm MSM 9625V2.1 MTP
[ 0.000000] qcom,ion-heap@28 reserved EBI1 size e9000
[ 0.000000] tmc@fc322000 reserved EBI1 size 20000
[ 0.000000] qcom,msm-rtb reserved EBI1 size 1000
[ 0.000000] Node qcom,msm-mem-hole removed memory 1c00000-6800000
[ 0.000000] memory pool 3 (start 0x07e00000 size 200000) initialized
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] IMEM DT static mapping successful
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 11782
[ 0.000000] Kernel command line: noinitrd root=/dev/mtdblock17 rw rootfstype=yaffs2 console=ttyHSL0,115200,n8 androidboot.hardware=qcom ehci-hcd.park=3 g-android.rx_trigger_enabled=1 androidboot.serialno=MDM9625 androidboot.baseband=msm
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 25MB 22MB = 47MB total
[ 0.000000] Memory: 38108k/38108k available, 12068k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8000000 - 0xff000000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc7d00000 ( 125 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06cd5f8 (6934 kB)
[ 0.000000] .init : 0xc06ce000 - 0xc06fa000 ( 176 kB)
[ 0.000000] .data : 0xc06fa000 - 0xc075d838 ( 399 kB)
[ 0.000000] .bss : 0xc075d878 - 0xc09289f8 (1837 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00540000, Cache size: 262144 B
[ 0.000000] sched_clock: 32 bits at 19MHz, resolution 52ns, wraps every 223696ms
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] Console: colour dummy device 80x30
[ 0.000103] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000110] pid_max: default: 32768 minimum: 301
[ 0.000279] Mount-cache hash table entries: 512
[ 0.000738] Initializing cgroup subsys debug
[ 0.000750] Initializing cgroup subsys cpuacct
[ 0.000757] Initializing cgroup subsys freezer
[ 0.000807] CPU: Testing write buffer coherency: ok
[ 0.000974] hw perfevents: enabled with ARMv7 Cortex-A5 PMU driver, 3 counters available
[ 0.001774] Setting up static identity map for 0x7ca8c0 - 0x7ca924
[ 0.001784] MSM Memory Dump table set up
[ 0.006618] dummy:
[ 0.006916] NET: Registered protocol family 16
[ 0.007553] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.008422] KPI: Bootloader start count = 126317
[ 0.008431] KPI: Bootloader end count = 217480
[ 0.008437] KPI: Bootloader display count = 4277659074
[ 0.008444] KPI: Bootloader load kernel count = 20619
[ 0.008451] KPI: Kernel MPM timestamp = 226138
[ 0.008456] KPI: Kernel MPM Clock frequency = 32768
[ 0.008472] socinfo_print: v8, id=149, ver=2.2, raw_id=2033, raw_ver=3, hw_plat=7, hw_plat_ver=65536
[ 0.008472] accessory_chip=0, hw_plat_subtype=0, pmic_model=65539, pmic_die_revision=131074
[ 0.012088] gpiochip_add: registered GPIOs 0 to 75 on device: msmgpio
[ 0.013424] msm_watchdog f9017000.qcom,wdt: MSM Watchdog Initialized
[ 0.015079] spmi_pmic_arb fc4cf000.qcom,spmi: PPID 0x34: APID 0xa already mapped
[ 0.015139] spmi_pmic_arb fc4cf000.qcom,spmi: PPID 0x34: APID 0xa already mapped
[ 0.015198] spmi_pmic_arb fc4cf000.qcom,spmi: PPID 0x34: APID 0xa already mapped
[ 0.022201] Notify: smsm init
[ 0.025129] 8019_s1: 800 <--> 1050 mV at 1050 mV normal idle
[ 0.025717] 8019_s2: 1250 mV normal idle
[ 0.026265] 8019_s3: 1000 <--> 1100 mV at 1100 mV normal idle
[ 0.026569] 8019_s3_ao: 1000 <--> 1100 mV at 0 mV normal idle
[ 0.027064] 8019_s4: 1800 <--> 2075 mV at 2075 mV normal idle
[ 0.027366] 8019_l1: 1225 mV normal idle
[ 0.027410] 8019_l1: supplied by 8019_s2
[ 0.027722] 8019_l2: 1800 mV normal idle
[ 0.027751] 8019_l2: supplied by 8019_s4
[ 0.028057] 8019_l3: 1800 mV normal idle
[ 0.028085] 8019_l3: supplied by 8019_s4
[ 0.028415] 8019_l4: 3075 mV normal idle
[ 0.028717] 8019_l5: 1800 <--> 2850 mV at 1800 mV normal idle
[ 0.029016] 8019_l6: 1800 <--> 2850 mV at 1800 mV normal idle
[ 0.029322] 8019_l7: 1800 mV normal idle
[ 0.029355] 8019_l7: supplied by 8019_s4
[ 0.029675] 8019_l8: 2050 mV normal idle
[ 0.029705] 8019_l8: supplied by 8019_s4
[ 0.030268] 8019_l9: 1200 mV normal idle
[ 0.030307] 8019_l9: supplied by 8019_s2
[ 0.030693] 8019_l10: 500 <--> 1050 mV at 0 mV normal idle
[ 0.030726] 8019_l10: supplied by 8019_s3
[ 0.031036] 8019_l10_corner: 0 <--> 0 mV at 0 mV normal idle
[ 0.031328] 8019_l10_corner_ao: 0 <--> 0 mV at 0 mV normal idle
[ 0.031616] 8019_l10_floor_corner: 0 <--> 0 mV at 0 mV normal idle
[ 0.032230] 8019_l11: 1800 mV normal idle
[ 0.032272] 8019_l11: supplied by 8019_s4
[ 0.032611] 8019_l12: 675 <--> 1050 mV at 0 mV normal idle
[ 0.032654] 8019_l12: supplied by 8019_s3
[ 0.032973] 8019_l12_ao: 675 <--> 1050 mV at 0 mV normal idle
[ 0.033005] 8019_l12_ao: supplied by 8019_s3_ao
[ 0.033309] 8019_l12_so: 675 <--> 1050 mV at 675 mV normal idle
[ 0.033341] 8019_l12_so: supplied by 8019_s3
[ 0.033673] 8019_l13: 1800 <--> 2950 mV at 2950 mV normal idle
[ 0.033988] 8019_l14: 2700 mV normal idle
[ 0.041028] msm-thermal qcom,msm-thermal.20: probe_psm:Failed reading node=/soc/qcom,msm-thermal, key=qcom,pmic-sw-mode-temp. KTM continues
[ 0.041361] hw-breakpoint: Debug register access (0xee001eb3) caused undefined instruction on CPU 0
[ 0.041372] hw-breakpoint: Debug register access (0xee001e93) caused undefined instruction on CPU 0
[ 0.042763] qup_i2c f9925000.i2c: Missing 'qcom,master-id' DT entry
[ 0.043510] sps:BAM 0xf9984000 (va:0xc80a0000) enabled: ver:0x7, number of pipes:20
[ 0.043529] sps:BAM 0xf9984000 is registered.
[ 0.044336] sps:sps is ready.
[ 0.044338] gdsc_usb_hsic:
[ 0.044529] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
[ 0.044877] Error: Unable to find clock from of_node
[ 0.044886] Error getting clocks
[ 0.044897] AXI: msm_bus_fabric_probe(): Coresight support absent for bus: 1024
[ 0.045049] Error: Unable to find clock from of_node
[ 0.045055] Error getting clocks
[ 0.045063] AXI: msm_bus_fabric_probe(): Coresight support absent for bus: 0
[ 0.045243] Error: Unable to find clock from of_node
[ 0.045249] Error getting clocks
[ 0.045257] AXI: msm_bus_fabric_probe(): Coresight support absent for bus: 4096
[ 0.045455] Error: Unable to find clock from of_node
[ 0.045462] Error getting clocks
[ 0.045470] AXI: msm_bus_fabric_probe(): Coresight support absent for bus: 5120
[ 0.057467] bio: create slab <bio-0> at 0
[ 0.057929] platform regulator-isl80101.27: Driver reg-fixed-voltage requests probe deferral
[ 0.058082] usb_vbus:
[ 0.058766] ION heap vmalloc created
[ 0.058892] ION heap iommu created
[ 0.058920] ION heap audio created at 0x07e01000 with size e9000
[ 0.059455] SCSI subsystem initialized
[ 0.059592] usbcore: registered new interface driver usbfs
[ 0.059660] usbcore: registered new interface driver hub
[ 0.059787] usbcore: registered new device driver usb
[ 0.072644] sps:BAM 0xfd4c4000 is registered.
[ 0.072647] sps:BAM 0xfd4c4000 (va:0xc80e0000) enabled: ver:0x21, number of pipes:20
[ 0.115976] ipa ipa_pipe_mem_init:1166 no IPA pipe mem alloted
[ 0.116425] sps:BAM 0xfc834000 is registered.
[ 0.116427] ipa connect_to_bam:570 connect_to_bam:
[ 0.117919] ipa ipa_cfg_ep_holb:1005 cfg holb 1 ep=7 tmr=511
[ 0.118180] ipa ipa_cfg_ep_holb:1005 cfg holb 1 ep=9 tmr=511
[ 0.118535] CCCC restart_reason 0
[ 0.122089] Switching to clocksource arch_sys_counter
[ 0.135257] NET: Registered protocol family 2
[ 0.135470] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.135819] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.135875] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.135971] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.135980] TCP: reno registered
[ 0.135994] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.136016] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.136249] NET: Registered protocol family 1
[ 0.137716] L2CC PMU device found. DEBUG_CTRL: 4
[ 0.139749] gpiochip_add: registered GPIOs 992 to 1023 on device: smp2p
[ 0.140267] gpiochip_add: registered GPIOs 960 to 991 on device: smp2p
[ 0.140415] gpiochip_add: registered GPIOs 928 to 959 on device: smp2p
[ 0.140962] gpiochip_add: registered GPIOs 896 to 927 on device: smp2p
[ 0.141071] gpiochip_add: registered GPIOs 864 to 895 on device: slave-kernel
[ 0.141685] gpiochip_add: registered GPIOs 832 to 863 on device: master-kernel
[ 0.141864] gpiochip_add: registered GPIOs 800 to 831 on device: smp2p
[ 0.142520] gpiochip_add: registered GPIOs 768 to 799 on device: smp2p
[ 0.142960] AXI: msm_bus_scale_register_client(): Master 6 not supported. Client cannot be registered
[ 0.142970] scm-pas: unable to register bus client
[ 0.147782] NET: Registered protocol family 27
[ 0.150110] cpufreq_table_init: CPU: 4 scaling frequencies supported.
[ 0.150633] msm_rpm_log_probe: OK
[ 0.158735] fuse init (API version 7.18)
[ 0.159180] msgmni has been set to 74
[ 0.160615] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.160628] io scheduler noop registered
[ 0.160634] io scheduler deadline registered
[ 0.160652] io scheduler row registered
[ 0.160675] io scheduler cfq registered (default)
[ 0.160943] spmi_pmic_arb fc4cf000.qcom,spmi: PPID 0xc0 incorrect owner 2
[ 0.161043] spmi_pmic_arb fc4cf000.qcom,spmi: PPID 0xc1 incorrect owner 2
[ 0.161343] spmi_pmic_arb fc4cf000.qcom,spmi: PPID 0xc4 incorrect owner 2
[ 0.161561] gpiochip_add: registered GPIOs 762 to 767 on device: pm8019-gpio
[ 0.162756] gpiochip_add: registered GPIOs 756 to 761 on device: pm8019-mpp
[ 0.164002] msm_serial_hs module loaded
[ 0.164131] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
[ 0.164306] msm_serial_hsl.0: ttyHSL0 at MMIO 0xf991f000 (irq = 141) is a MSM
[ 0.165836] msm_hsl_console_setup: console setup on port #0
[ 1.166293] console [ttyHSL0] enabled
[ 1.170258] msm_serial_hsl_init: driver initialized
[ 1.178234] diag: In diag_send_msg_mask_update, invalid status 0
[ 1.187480] diagchar initialized now
[ 1.187483] brd: module loaded
[ 1.195374] loop: module loaded
[ 1.197994] SCSI Media Changer driver v0.25
[ 1.202320] sps: BAM device 0xf9ac4000 is not registered yet.
[ 1.207476] sps:BAM 0xf9ac4000 is registered.
[ 1.207477] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xc78b3400
[ 1.220509] sps:BAM 0xf9ac4000 (va:0xc81c0000) enabled: ver:0x14, number of pipes:7
[ 1.228236] msm_nand_parse_smem_ptable: Parsing partition table info from SMEM
[ 1.235301] msm_nand_parse_smem_ptable: SMEM partition table found: ver: 4 len: 19
[ 1.242863] msm_nand_version_check: nand_major:1, nand_minor:1, qpic_major:1, qpic_minor:2
[ 1.251106] msm_nand_flash_onfi_probe: Found a non ONFI device
[ 1.256924] msm_nand_scan: NAND Id: 0x1590aac8 Buswidth: 8Bits Density: 256 MByte
[ 1.264336] msm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes)
[ 1.271868] msm_nand_scan: BCH ECC: 4 Bit
[ 1.275886] msm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c
[ 1.275886] RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d
[ 1.275886] ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700
[ 1.275886] BAD BLOCK BYTE: 0x000001d1
[ 1.298602] Creating 19 MTD partitions on "f9ac0000.qcom,nand":
[ 1.304446] 0x000000000000-0x000000140000 : "sbl"
[ 1.309806] 0x000000140000-0x000000280000 : "mibib"
[ 1.314593] 0x000000280000-0x000000d80000 : "efs2"
[ 1.319310] 0x000000d80000-0x0000010e0000 : "sdi"
[ 1.324058] 0x0000010e0000-0x000001440000 : "tz"
[ 1.328628] 0x000001440000-0x000001500000 : "mba"
[ 1.333366] 0x000001500000-0x000001860000 : "rpm"
[ 1.337986] 0x000001860000-0x000004b20000 : "qdsp"
[ 1.342747] 0x000004b20000-0x000004b60000 : "pad"
[ 1.347407] 0x000004b60000-0x000004c40000 : "appsbl"
[ 1.352429] 0x000004c40000-0x000005680000 : "apps"
[ 1.357169] 0x000005680000-0x0000056c0000 : "scrub"
[ 1.362029] 0x0000056c0000-0x000009820000 : "cache"
[ 1.366942] 0x000009820000-0x000009c80000 : "misc"
[ 1.371694] 0x000009c80000-0x00000a6e0000 : "recovery"
[ 1.376867] 0x00000a6e0000-0x00000a840000 : "fota"
[ 1.381570] 0x00000a840000-0x00000a880000 : "recoveryfs"
[ 1.386875] 0x00000a880000-0x00000cd20000 : "system"
[ 1.391773] 0x00000cd20000-0x000010000000 : "userdata"
[ 1.396953] msm_nand_probe: NANDc phys addr 0xf9ac0000, BAM phys addr 0xf9ac4000, BAM IRQ 279
[ 1.404887] msm_nand_probe: Allocated DMA buffer at virt_addr 0xc81ba000, phys_addr 0x7bb6000
[ 1.413775] msm_otg f9a55000.usb: msm_otg probe
[ 1.418076] msm_otg f9a55000.usb: failed to get phy_clk
[ 1.423163] msm_otg f9a55000.usb: OTG regs = c81ce000
[ 1.429614] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.448178] msm_hsic_host msm_hsic_host: Qualcomm EHCI Host Controller using HSIC
[ 1.454675] msm_hsic_host msm_hsic_host: new USB bus registered, assigned bus number 1
[ 1.492176] msm_hsic_host msm_hsic_host: irq 168, io mem 0xf9a15000
[ 1.512150] msm_hsic_host msm_hsic_host: USB 2.0 started, EHCI 1.00
[ 1.517592] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.524171] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.531350] usb usb1: Product: Qualcomm EHCI Host Controller using HSIC
[ 1.537963] usb usb1: Manufacturer: Linux 3.4.0+ ehci_hcd
[ 1.543395] usb usb1: SerialNumber: msm_hsic_host
[ 1.548419] hub 1-0:1.0: USB hub found
[ 1.551778] hub 1-0:1.0: 1 port detected
[ 1.556294] hbm_init
[ 1.559423] Initializing USB Mass Storage driver...
[ 1.563403] usbcore: registered new interface driver usb-storage
[ 1.569248] USB Mass Storage support registered.
[ 1.573925] usbcore: registered new interface driver ums-alauda
[ 1.579784] usbcore: registered new interface driver ums-cypress
[ 1.585795] usbcore: registered new interface driver ums-datafab
[ 1.591762] usbcore: registered new interface driver ums-freecom
[ 1.597771] usbcore: registered new interface driver ums-isd200
[ 1.603673] usbcore: registered new interface driver ums-jumpshot
[ 1.609730] usbcore: registered new interface driver ums-karma
[ 1.615566] usbcore: registered new interface driver ums-onetouch
[ 1.621624] usbcore: registered new interface driver ums-sddr09
[ 1.627548] usbcore: registered new interface driver ums-sddr55
[ 1.633457] usbcore: registered new interface driver ums-usbat
[ 1.639252] usbcore: registered new interface driver usb_ehset_test
[ 1.645900] msm_otg f9a55000.usb: phy_reset: success
[ 1.650917] msm_hsusb msm_hsusb: [ci13xxx_start] hw_ep_max = 32
[ 1.658603] mbim_init: initialize 1 instances
[ 1.661998] mbim_init: Initialized 1 ports
[ 1.667614] rndis_qc_init: initialize rndis QC instance
[ 1.672224] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.678658] android_usb gadget: Number of LUNs=1
[ 1.683284] lun0: LUN: removable file: (no medium)
[ 1.688348] android_usb gadget: android_usb ready
[ 1.694189] using rtc device, qpnp_rtc, for alarms
[ 1.694192] qcom,qpnp-rtc qpnp-rtc-c75cbc00: rtc core: registered qpnp_rtc as rtc0
[ 1.705755] i2c /dev entries driver
[ 1.744948] mp2617 mp2617.31: mp2617_probe: MP2617 charger probed successfully
[ 1.752399] spmi_pmic_arb fc4cf000.qcom,spmi: int enable: invalid APID 256
[ 1.758483] spmi_pmic_arb fc4cf000.qcom,spmi: int enable: invalid APID 256
[ 1.765207] spmi_pmic_arb fc4cf000.qcom,spmi: int enable: invalid APID 256
[ 1.781743] cpuidle: using governor ladder
[ 1.784973] cpuidle: using governor menu
[ 1.788979] msm_sdcc msm_sdcc.2: no qcom,vdd-voltage-level property
[ 1.795051] msm_sdcc msm_sdcc.2: no qcom,vdd-current-level property
[ 1.801417] mmc0: SDCC Version: 0x00000038
[ 1.805349] msm_sdcc msm_sdcc.2: qcom,bus-bw-vectors-bps not specified
[ 1.811894] msmsdcc_vreg_init_reg: regulator_get(vdd) failed. rc=-517
[ 1.818239] msmsdcc_probe: msmsdcc_vreg_init() failed (-517)
[ 1.823930] platform msm_sdcc.2: Driver msm_sdcc requests probe deferral
[ 1.831533] usbcore: registered new interface driver usbhid
[ 1.836139] usbhid: USB HID core driver
[ 1.840004] logger: created 256K log 'log_main'
[ 1.844530] logger: created 64K log 'log_events'
[ 1.849096] logger: created 256K log 'log_radio'
[ 1.853773] logger: created 64K log 'log_system'
[ 1.858766] sps:BAM 0xf9a44000 is registered.
[ 1.863082] sps:BAM 0xf9a04000 is registered.
[ 1.863084] input: qpnp_pon as /devices/virtual/input/input0
[ 1.873125] coresight-cti fc308000.cti: CTI initialized
[ 1.877878] coresight-cti fc309000.cti: CTI initialized
[ 1.883172] msm_otg f9a55000.usb: Avail curr from USB = 500
[ 1.889029] coresight-cti fc30a000.cti: CTI initialized
[ 1.894214] coresight-cti fc30b000.cti: CTI initialized
[ 1.899239] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_RESET_EVENT received
[ 1.905862] coresight-cti fc30c000.cti: CTI initialized
[ 1.911016] coresight-cti fc30d000.cti: CTI initialized
[ 1.916280] coresight-cti fc30e000.cti: CTI initialized
[ 1.921311] ipa disconnect_to_bam:660 disconnect_to_bam
[ 1.926618] coresight-cti fc30f000.cti: CTI initialized
[ 1.931790] coresight-cti fc310000.cti: CTI initialized
[ 1.937758] coresight-cti fc333000.cti: CTI initialized
[ 1.942526] coresight-csr fc302000.csr: CSR initialized
[ 1.947926] sps:BAM 0xfc37c000 is registered.
[ 1.947929] coresight-tmc fc322000.tmc: TMC initialized
[ 1.957158] coresight-tmc fc307000.tmc: TMC initialized
[ 1.962431] platform fc318000.tpiu: Driver coresight-tpiu requests probe deferral
[ 1.969840] coresight-funnel fc31b000.funnel: FUNNEL initialized
[ 1.975661] coresight-funnel fc319000.funnel: FUNNEL initialized
[ 1.981597] coresight-funnel fc31a000.funnel: FUNNEL initialized
[ 1.987818] coresight-replicator fc31c000.replicator: REPLICATOR initialized
[ 1.994940] coresight-stm fc321000.stm: STM initialized
[ 2.000021] coresight-hwevent f9011038.hwevent: Hardware Event driver initialized
[ 2.007698] coresight-etm fc332000.etm: ETM initialized
[ 2.012672] Netfilter messages via NETLINK v0.30.
[ 2.017161] nf_conntrack version 0.5.0 (595 buckets, 5120 max)
[ 2.023418] ctnetlink v0.93: registering with nfnetlink.
[ 2.028270] ip_set: protocol 6
[ 2.031597] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.036749] TCP: cubic registered
[ 2.040348] NET: Registered protocol family 10
[ 2.045053] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.049806] IPv6 over IPv4 tunneling driver
[ 2.054391] NET: Registered protocol family 17
[ 2.058316] Bridge firewalling registered
[ 2.062271] Ebtables v2.0 registered
[ 2.066218] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 2.073471] clock_late_init: Removing enables held for handed-off clocks
[ 2.084361] usb_vbus: incomplete constraints, leaving on
[ 2.089139] platform fc318000.tpiu: Driver coresight-tpiu requests probe deferral
[ 2.096169] wwan_init: WWAN devices[8]
[ 2.100510] add mac address 6e 6d c8 2b 6b 66
[ 2.104404] add mac address ca 97 97 5a 19 10
[ 2.104406] msm_sdcc msm_sdcc.2: no qcom,vdd-voltage-level property
[ 2.115850] add mac address a6 b7 29 cf 7f d7
[ 2.119671] add mac address be 9e e8 68 a2 c2
[ 2.123574] add mac address b2 f f5 d7 9a f7
[ 2.123576] msm_sdcc msm_sdcc.2: no qcom,vdd-current-level property
[ 2.135091] add mac address a2 83 e 4 c3 8
[ 2.138686] add mac address 46 71 3a 6d ce 44
[ 2.143264] add mac address 7a 5 29 fc a7 f4
[ 2.147335] input: gpio-keys as /devices/gpio-keys.26/input/input1
[ 2.153182] mmc0: SDCC Version: 0x00000038
[ 2.156993] msm_sdcc msm_sdcc.2: qcom,bus-bw-vectors-bps not specified
[ 2.163934] msmsdcc_vreg_init_reg: regulator_get(vdd) failed. rc=-517
[ 2.169922] msmsdcc_probe: msmsdcc_vreg_init() failed (-517)
[ 2.175839] qcom,qpnp-rtc qpnp-rtc-c75cbc00: setting system clock to 1970-01-01 00:00:09 U[ 2.184847] platform msm_sdcc.2: Driver msm_sdcc requests probe deferral
[ 2.190671] yaffs: dev is 32505873 name is "mtdblock17" rw
[ 2.196320] ext_2p95v:
[ 2.198727] coresight-tpiu fc318000.tpiu: sdc voltage levels not specified
[ 2.205323] yaffs: passed flags ""
[ 2.208809] coresight-tpiu fc318000.tpiu: sdc current levels not specified
[ 2.215620] coresight-tpiu fc318000.tpiu: seta gpios not specified
[ 2.221722] coresight-tpiu fc318000.tpiu: setb gpios not specified
[ 2.228063] coresight-tpiu fc318000.tpiu: TPIU initialized
[ 2.233632] msm_sdcc msm_sdcc.2: no qcom,vdd-voltage-level property
[ 2.239607] msm_sdcc msm_sdcc.2: no qcom,vdd-current-level property
[ 2.246156] mmc0: SDCC Version: 0x00000038
[ 2.249935] msm_sdcc msm_sdcc.2: qcom,bus-bw-vectors-bps not specified
[ 2.257305] mmc0: bam physical base=0xf9884000
[ 2.260875] mmc0: bam virtual base=0xc8268000
[ 2.265250] sps:BAM 0xf9884000 is registered.
[ 2.270079] mmc0: BAM device registered. bam_handle=0xc6e67200
[ 2.270081] sps:BAM 0xf9884000 (va:0xc8268000) enabled: ver:0x7, number of pipes:6
[ 2.283637] mmc0: Qualcomm MSM SDCC-BAM at [mem 0xf9884000-0xf988afff flags 0x200] [irq 252 flags 0x400]
[ 2.292474] mmc0: Qualcomm MSM SDCC-DML [mem 0xf98a4800-0xf98a48ff flags 0x200]
[ 2.299717] mmc0: No card detect facilities available
[ 2.306985] mmc0: Qualcomm MSM SDCC-core [mem 0xf98a4000-0xf98a47ff flags 0x200] [irq 157 flags 0x400],0 dma -1 dmacrcri -1
[ 2.317351] mmc0: Controller capabilities: 0x00003ffe
[ 2.322278] mmc0: 8 bit data mode disabled
[ 2.326236] mmc0: 4 bit data mode enabled
[ 2.330226] mmc0: polling status mode disabled
[ 2.334805] mmc0: MMC clock 400000 -> 200000000 Hz, PCLK 0 Hz
[ 2.340385] mmc0: Slot eject status = 0
[ 2.344225] mmc0: Power save feature enable = 1
[ 2.348769] mmc0: SPS-BAM data transfer mode available
[ 4.658188] VFS: Mounted root (yaffs2 filesystem) on device 31:17.
[ 4.663891] Freeing init memory: 176K
INIT: version 2.88 booting
Starting Bootlog daemon: bootlogd.
[ 5.697767] yaffs: dev is 32505874 name is "mtdblock18" rw
[ 5.702282] yaffs: passed flags ""
[ 5.725820] yaffs: dev is 32505868 name is "mtdblock12" rw
[ 5.730267] yaffs: passed flags ""
[ 9.828551] yaffs: dev is 32505869 name is "mtdblock13" rw
[ 9.833170] yaffs: passed flags ""
DEVICE_CODE is already burned.
Configuring network interfaces... ifdown: interface lo not configured
ifdown: interface eth0 not configured
Cannot find device "eth0"
done.
[ 10.192708] msm_hsic_host msm_hsic_host: remove, state 1
[ 10.197001] usb usb1: USB disconnect, device number 1
ODU supported=N enabled=N
Shutdown EHCI HSIC device
[ 10.208648] msm_hsic_host msm_hsic_host: USB bus 1 deregistered
[ 10.290307] enable_store: android_usb: already disabled
Starting adbd: done
[ 10.350998] adb_open
[ 10.352339] rndis_function_bind_config: rndis_function_bind_config MAC: 00:00:00:00:00:00
[ 10.360504] android_usb gadget: using random self ethernet address
[ 10.366611] android_usb gadget: using random host ethernet address
net.core.rmem_default = 1048576
net.core.wmem_default = 1048576
net.core.rmem_max = 1048576
net.core.wmem_max = 1048576
net.ipv4.tcp_timestamps = 0
ne[ 10.383700] rndis0: MAC 66:df:c1:5d:4e:5e
[ 10.391960] rndis0: HOST MAC fe:63:1b:21:61:86
t.ipv4.tcp_sack = 1
net.ipv4.tcp_window_scaling = 1
[ 10.399826] adb_bind_config
[ 10.415124] msm_hsusb msm_hsusb: CI13XXX_CONTROLLER_CONNECT_EVENT received
Thu Mar 17 09:11:00 UTC 2016
hwclock: RTC_SET_TIME: Invalid argument
No package system found
INIT: Entering runlevel: 5
Starting ubusd daemon: ubusd.
Starting usb_daemon: done
Starting key detect daemon: key_detect.
Starting ledd: [ 10.548097] msm_otg f9a55000.usb: Avail curr from USB = 100
[ 10.552821] mp2617 mp2617.31: mp2617_set_input_current_limit: Unsupported current_limit_ua=100000 uA
[ 10.562959] android_work: android_work: did not send uevent (0 0 (null))
done
Starting state_mgr daemon.
[ 10.670221] android_work: android_work: sent uevent USB_STATE=CONNECTED
[ 10.681369] android_work: android_work: sent uevent USB_STATE=DISCONNECTED
Starting syslogd/klogd: done
Starting diagrebootapp: done
Starting qrngd: done
Starting atreset: [ 10.733816] warning: `qrngd' uses 32-bit capabilities (legacy support in use)
done
starting DNS forwarder and DHCP server: dnsmasq... [ 10.798194] android_work: android_work: sent uevent USB_STATE=CONNECTED
[ 10.817326] android_usb gadget: high-speed config #1: fe8078c8.android_usb
[ 10.823317] msm_otg f9a55000.usb: Avail curr from USB = 500
done.
[ 10.884632] android_work: android_work: sent uevent USB_STATE=CONFIGURED
Starting qmuxd: done
Starting power_consumptiond daemon.
Starting thermal-engine: done
Starting adbd: /sbin/adbd is already running
237
Starting netmgrd: done
[ 11.083429] msm_thermal: enabled = 0
Starting powerconfig for 9x25: done
Starting QCMAP_ConnectionManager: 11.127521] QCMAP:start
[ 11.131571] ipa connect_to_bam:570 connect_to_bam:
[ 11.139004] ipa ipa_cfg_ep_holb:1005 cfg holb 1 ep=7 tmr=511
done
[ 11.148819] ipa ipa_cfg_ep_holb:1005 cfg holb 1 ep=9 tmr=511
Starting rild daemon: rild started.
Starting tpril daemon: tpril started.
Starting ipacm: done
Starting qti: [ 11.268070] QTI:start
done
Starting QCMAP_Web_CLIENT: done
Stopping Bootlog daemon: bootlogd.
Starting make_swap.
[ 11.744414] USB QCMAP NL IOCTL Snd GETNEIGH Succ
Starting updatecheck daemon: updatecheck started.
prepare U disk
[ 11.912338] lun0: unable to open backing file: /dev/mmcblk0
INIT: cannot execute "/usr/bin/mbimd"
INIT: cannot execute "/usr/bin/mbimd"
cat: can't open '/tmp/isshutdown': No such file or directory
INIT: cannot execute "/usr/bin/mbimd"
INIT: cannot execute "/usr/bin/mbimd"
399
INIT: cannot execute "/usr/bin/mbimd"
INIT: cannot execute "/usr/bin/mbimd"
426
[ 13.158677] ipa disconnect_to_bam:660 disconnect_to_bam
287
INIT: cannot execute "/usr/bin/mbimd"
OpenEmbedded Linux mdm9625 ttyHSL0
msm 20160317 mdm9625 ttyHSL0
mdm9625 login:
INIT: cannot execute "/usr/bin/mbimd"
406
403
INIT: cannot execute "/usr/bin/mbimd"
399
INIT: cannot execute "/usr/bin/mbimd"[ 13.768726] device rndis0 entered promiscuous mode
INIT: Id "m2" respawning too fast: disabled for 5 minutes
310
[ 13.866257] USB Client mac Address is 66:df:c1:5d:4e:5e
[ 15.840709] Adding 5116k swap on /dev/loop6. Priority:-1 extents:1 across:5116k
[ 16.199512] fastnat init
[ 16.279146] QCMAP:Init Complete
[ 16.296130] QTI:Enable mobileap
[ 16.419410] bridge0: port 1(rndis0) entered forwarding state
[ 16.424125] bridge0: port 1(rndis0) entered forwarding state
[ 16.460185] QTI:RNDIS mode
[ 16.464954] QTI:LINK_UP message posted
[ 16.629760] QTI:LINK_DOWN_WAIT state
cat: can't open '/tmp/isshutdown': No such file or directory
399
426
287
406
403
399
310
cat: can't open '/tmp/isshutdown': No such file or directory
399
426
287
406
403
399
310
cat: can't open '/tmp/isshutdown': No such file or directory
399
426
287
406
403
399
310
[ 31.313901] USB Client mac Address is fe:63:1b:21:61:86
[ 31.442148] bridge0: port 1(rndis0) entered forwarding state
cat: can't open '/tmp/isshutdown': No such file or directory
399
426
287
406
403
399
310
cat: can't open '/tmp/isshutdown': No such file or directory
399
426
287
406
403
399
594
595
310
cat: can't open '/tmp/isshutdown': No such file or directory
399
426
287
406
403
399
594
595
310
cat: can't open '/tmp/isshutdown': No such file or directory
