1 Temat przez santaclaus21 (edytowany przez santaclaus21 2017-04-04 23:36:34)

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Temat: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

OpenWRT docelowy postawiłem, więc jest nowy wątek smile Mam problem z inicjalizacją modemu MF823. Nie widzę konfliktów w logach, nawet widać, że coś wykrywa...

Profilaktycznie doinstalowałem: opkg install kmod-usb-core kmod-usb2 usb-modeswitch libusb-1.0

Apr  4 20:50:07 OpenWrt kern.info kernel: [   15.188000] usb 1-1: new high-speed USB device number 2 using dwc_otg
Apr  4 20:50:07 OpenWrt kern.info kernel: [   15.380000] hub 1-1:1.0: USB hub found
Apr  4 20:50:07 OpenWrt kern.info kernel: [   15.384000] hub 1-1:1.0: 4 ports detected
Apr  4 20:50:13 OpenWrt kern.info kernel: [   23.116000] usb 1-1.2: new high-speed USB device number 3 using dwc_otg
Apr  4 20:50:14 OpenWrt kern.info kernel: [   23.720000] device eth0 entered promiscuous mode

Ale w LUCI w konfiguracji WAN widzę tylko eth0 i wwan. Trzeba jakoś z palca wpisać USB? Jeśli tak to skąd mam wiedzieć które dokładnie. Any help?

Wrócilem do LEDE, poinstalowałem większość znanych mi sterowników do modemow, USB0 dalej brak. Co więcej - nie widzę, żeby cokolwiek się wywalało, modem wpięty. Czego brakuje żeby go odpalić?
-------------------------
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.000000] Linux version 4.4.50 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] SoC: Danube rev 1.3
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] bootconsole [early0] enabled
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] MIPS: machine is ARV752DPW - Arcor 802
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Determined physical RAM map:
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000]  memory: 04000000 @ 00000000 (usable)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Zone ranges:
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Movable zone start for each node
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Early memory node ranges
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000] On node 0 totalpages: 16384
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 8046e4b0, node_mem_map 81007880
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000]   Normal zone: 128 pages used for memmap
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
Tue Apr  4 22:06:09 2017 kern.warn kernel: [    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
Tue Apr  4 22:06:09 2017 kern.warn kernel: [    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.000000] Kernel command line: console=ttyLTQ0,115200
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Writing ErrCtl register=0005a999
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Readback ErrCtl register=0005a999
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] Memory: 58792K/65536K available (3875K kernel code, 156K rwdata, 620K rodata, 1220K init, 200K bss, 6744K reserved, 0K cma-reserved)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] NR_IRQS:256
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] CPU Clock: 333MHz
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.000018] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.007956] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.050570] pid_max: default: 32768 minimum: 301
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.055535] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.062089] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.079119] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.088902] pinctrl core: initialized pinctrl subsystem
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.096371] NET: Registered protocol family 16
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.109088] pinctrl-xway 1e100b10.pinmux: Init done
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.115639] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.192931] PCI host bridge /fpi@10000000/pci@E105400 ranges:
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.198636]  MEM 0x0000000018000000..0x0000000019ffffff
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.203906]   IO 0x000000001ae00000..0x000000001affffff
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.238014] usbcore: registered new interface driver usbfs
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.243644] usbcore: registered new interface driver hub
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.249106] usbcore: registered new device driver usb
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.254746] PCI host bridge to bus 0000:00
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.258802] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.265731] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.272677] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.279526] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.287633] pci 0000:00:0e.0: [1814:0601] type 00 class 0x028000
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.287729] pci 0000:00:0e.0: reg 0x10: [mem 0xffff0000-0xffffffff]
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.287895] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.288379] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.288457] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.296638] clocksource: Switched to clocksource MIPS
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.304158] NET: Registered protocol family 2
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.310318] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.317291] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.323682] TCP: Hash tables configured (established 1024 bind 1024)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.330262] UDP hash table entries: 256 (order: 0, 4096 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.336084] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.342809] NET: Registered protocol family 1
Tue Apr  4 22:06:09 2017 kern.debug kernel: [    0.347223] PCI: CLS 0 bytes, default 32
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.360768] gptu: totally 6 16-bit timers/counters
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.365714] gptu: misc_register on minor 63
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.369851] gptu: succeeded to request irq 126
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.374354] gptu: succeeded to request irq 127
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.378868] gptu: succeeded to request irq 128
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.383381] gptu: succeeded to request irq 129
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.387896] gptu: succeeded to request irq 130
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.392409] gptu: succeeded to request irq 131
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.403639] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.408999] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.416854] futex hash table entries: 256 (order: -1, 3072 bytes)
Tue Apr  4 22:06:09 2017 kern.warn kernel: [    0.422984] Crashlog allocated RAM at address 0x3f00000
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.467037] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.472805] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.489692] io scheduler noop registered
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.493556] io scheduler deadline registered (default)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.499858] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.508822] console [ttyLTQ0] enabled
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.515925] bootconsole [early0] disabled
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.525340] lantiq nor flash device: 00800000 at 10000000
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.529617] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.538577] Amd/Fujitsu Extended Query Table at 0x0040
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.543579]   Amd/Fujitsu Extended Query version 1.1.
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.548440] number of CFI chips: 1
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.551788] 4 ofpart partitions found on MTD device ltq_nor
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.557145] Creating 4 MTD partitions on "ltq_nor":
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.561880] 0x000000000000-0x000000010000 : "uboot"
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.573412] 0x000000010000-0x000000020000 : "uboot_env"
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.580999] 0x000000020000-0x0000007f0000 : "firmware"
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.629798] 2 uimage-fw partitions found on MTD device firmware
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.634251] 0x000000020000-0x00000019cb36 : "kernel"
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.642102] 0x00000019cb36-0x0000007f0000 : "rootfs"
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.649475] mtd: device 4 (rootfs) set to be root filesystem
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.653786] 1 squashfs-split partitions found on MTD device rootfs
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.659670] 0x000000490000-0x0000007f0000 : "rootfs_data"
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    0.668727] 0x0000007f0000-0x000000800000 : "board_config"
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.699552] libphy: ltq_mii: probed
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.794842] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.800710] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.810518] wdt 1f8803f0.watchdog: Init done
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.820128] NET: Registered protocol family 10
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.836959] NET: Registered protocol family 17
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.840015] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.852212] 8021q: 802.1Q VLAN Support v1.8
Tue Apr  4 22:06:09 2017 kern.warn kernel: [    0.864563] fdt: not creating '/sys/firmware/fdt': CRC check failed
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.884991] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Tue Apr  4 22:06:09 2017 kern.info kernel: [    0.898320] Freeing unused kernel memory: 1220K (8048f000 - 805c0000)
Tue Apr  4 22:06:09 2017 user.info kernel: [    3.345116] init: Console is alive
Tue Apr  4 22:06:09 2017 user.info kernel: [    3.347534] init: - watchdog -
Tue Apr  4 22:06:09 2017 kern.info kernel: [    6.143755] dwc2 1e101000.ifxhcd: requested GPIO 464
Tue Apr  4 22:06:09 2017 kern.info kernel: [    7.005000] dwc2 1e101000.ifxhcd: DWC OTG Controller
Tue Apr  4 22:06:09 2017 kern.info kernel: [    7.008529] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
Tue Apr  4 22:06:09 2017 kern.info kernel: [    7.015694] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
Tue Apr  4 22:06:09 2017 kern.info kernel: [    7.023279] hub 1-0:1.0: USB hub found
Tue Apr  4 22:06:09 2017 kern.info kernel: [    7.026383] hub 1-0:1.0: 1 port detected
Tue Apr  4 22:06:09 2017 user.info kernel: [    7.041982] init: - preinit -
Tue Apr  4 22:06:09 2017 kern.warn kernel: [    7.183191] dwc2 1e101000.ifxhcd: Overcurrent change detected
Tue Apr  4 22:06:09 2017 kern.warn kernel: [    7.754268] dwc2 1e101000.ifxhcd: Overcurrent change detected
Tue Apr  4 22:06:09 2017 kern.notice kernel: [    8.137344] random: procd: uninitialized urandom read (4 bytes read, 33 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   11.652954] jffs2: notice: (372) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Tue Apr  4 22:06:09 2017 user.info kernel: [   11.676612] mount_root: switching to jffs2 overlay
Tue Apr  4 22:06:09 2017 user.warn kernel: [   11.704573] urandom-seed: Seeding with /etc/urandom.seed
Tue Apr  4 22:06:09 2017 user.info kernel: [   11.861361] procd: - early -
Tue Apr  4 22:06:09 2017 user.info kernel: [   11.863023] procd: - watchdog -
Tue Apr  4 22:06:09 2017 user.info kernel: [   12.739108] procd: - ubus -
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.208271] random: jshn: uninitialized urandom read (4 bytes read, 53 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.219347] random: ubusd: uninitialized urandom read (4 bytes read, 53 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.372982] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.381362] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.389279] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.398809] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.406645] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.415879] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   13.426231] random: ubusd: uninitialized urandom read (4 bytes read, 54 bits of entropy available)
Tue Apr  4 22:06:09 2017 user.info kernel: [   13.434773] procd: - init -
Tue Apr  4 22:06:09 2017 kern.info kernel: [   14.855109] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
Tue Apr  4 22:06:09 2017 kern.warn kernel: [   14.875303] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
Tue Apr  4 22:06:09 2017 kern.info kernel: [   14.889456] NET: Registered protocol family 8
Tue Apr  4 22:06:09 2017 kern.info kernel: [   14.892305] NET: Registered protocol family 20
Tue Apr  4 22:06:09 2017 kern.info kernel: [   14.907632] PPP generic driver version 2.4.2
Tue Apr  4 22:06:09 2017 kern.notice kernel: [   15.102991] SCSI subsystem initialized
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.218712] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.226049] ehci-platform: EHCI generic platform driver
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.237774] ip6_tables: (C) 2000-2006 Netfilter Core Team
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.259449] IFX MEI Version 5.00.00
Tue Apr  4 22:06:09 2017 kern.warn kernel: [   15.276270] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.295994] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.302065] Backport generated by backports.git backports-20160324-9-g0e38f5c
Tue Apr  4 22:06:09 2017 kern.warn kernel: [   15.327374] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.334588] request_timer(3, 0x000001AE, 1)...successful!
Tue Apr  4 22:06:09 2017 kern.warn kernel: [   15.340000] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.351717] ip_tables: (C) 2000-2006 Netfilter Core Team
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.366755] ATM1.0.26    ATM (A1) firmware version 0.17
Tue Apr  4 22:06:09 2017 kern.warn kernel: [   15.370526] ifxmips_atm: ATM init succeed
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.407607] nf_conntrack version 0.5.0 (937 buckets, 3748 max)
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.478205] NET: Registered protocol family 24
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.602106] usbcore: registered new interface driver usb-storage
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.677255] xt_time: kernel timezone is -0000
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.683462] usbcore: registered new interface driver cdc_ether
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.791943] usbcore: registered new interface driver rndis_host
Tue Apr  4 22:06:09 2017 kern.warn kernel: [   15.839659] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.845218] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.851126] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2860, rev 0103 detected
Tue Apr  4 22:06:09 2017 kern.info kernel: [   15.858644] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0001 detected
Tue Apr  4 22:06:09 2017 kern.debug kernel: [   15.866441] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Tue Apr  4 22:06:13 2017 user.notice : Added device handler type: 8021ad
Tue Apr  4 22:06:13 2017 user.notice : Added device handler type: 8021q
Tue Apr  4 22:06:13 2017 user.notice : Added device handler type: macvlan
Tue Apr  4 22:06:13 2017 user.notice : Added device handler type: bridge
Tue Apr  4 22:06:13 2017 user.notice : Added device handler type: Network device
Tue Apr  4 22:06:13 2017 user.notice : Added device handler type: tunnel
Tue Apr  4 22:06:15 2017 user.notice : /etc/rc.common: line 1: esi: not found
Tue Apr  4 22:06:19 2017 authpriv.info dropbear[826]: Not backgrounding
Tue Apr  4 22:06:21 2017 user.notice : setting up led wifi
Tue Apr  4 22:06:21 2017 user.notice : setting up led usb
Tue Apr  4 22:06:21 2017 user.notice : setting up led internet
Tue Apr  4 22:06:22 2017 kern.notice kernel: [   31.704766] random: nonblocking pool is initialized
Tue Apr  4 22:06:23 2017 kern.info kernel: [   32.925911] device eth0 entered promiscuous mode
Tue Apr  4 22:06:23 2017 kern.info kernel: [   32.936940] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Tue Apr  4 22:06:23 2017 daemon.notice netifd: Interface 'lan' is enabled
Tue Apr  4 22:06:23 2017 daemon.notice netifd: Interface 'lan' is setting up now
Tue Apr  4 22:06:23 2017 daemon.notice netifd: Interface 'lan' is now up
Tue Apr  4 22:06:23 2017 daemon.notice netifd: Interface 'loopback' is enabled
Tue Apr  4 22:06:23 2017 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Apr  4 22:06:23 2017 daemon.notice netifd: Interface 'loopback' is now up
Tue Apr  4 22:06:24 2017 local2.notice br2684ctl[788]: Interface "nas0" created sucessfully
Tue Apr  4 22:06:24 2017 local2.notice br2684ctl[788]: Communicating over ATM 0.1.32, encapsulation: LLC
Tue Apr  4 22:06:24 2017 daemon.info odhcpd[758]: Raising SIGUSR1 due to address change on br-lan
Tue Apr  4 22:06:24 2017 local2.info br2684ctl[788]: Interface configured
Tue Apr  4 22:06:24 2017 daemon.notice netifd: Network device 'lo' link is up
Tue Apr  4 22:06:24 2017 daemon.notice netifd: Interface 'loopback' has link connectivity
Tue Apr  4 22:06:24 2017 kern.info kernel: [   33.838146] IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready
Tue Apr  4 22:06:24 2017 daemon.notice netifd: Interface 'wan' is enabled
Tue Apr  4 22:06:24 2017 local2.info br2684ctl[788]: RFC 1483/2684 bridge daemon started
Tue Apr  4 22:06:25 2017 daemon.info odhcpd[758]: Initial RA router lifetime 0, 1 address(es) available on br-lan
Tue Apr  4 22:06:25 2017 daemon.notice odhcpd[758]: Failed to send to ff02::1%br-lan (Address not available)
Tue Apr  4 22:06:25 2017 kern.info kernel: [   34.853358] br-lan: port 1(eth0) entered forwarding state
Tue Apr  4 22:06:25 2017 kern.info kernel: [   34.857414] br-lan: port 1(eth0) entered forwarding state
Tue Apr  4 22:06:25 2017 kern.info kernel: [   34.862786] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Tue Apr  4 22:06:25 2017 daemon.notice netifd: Network device 'eth0' link is up
Tue Apr  4 22:06:25 2017 daemon.notice netifd: bridge 'br-lan' link is up
Tue Apr  4 22:06:25 2017 daemon.notice netifd: Interface 'lan' has link connectivity
Tue Apr  4 22:06:25 2017 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Apr  4 22:06:26 2017 daemon.notice netifd: radio0 (909): command failed: Not supported (-122)
Tue Apr  4 22:06:26 2017 daemon.info procd: - init complete -
Tue Apr  4 22:06:26 2017 daemon.info odhcpd[758]: Initial RA router lifetime 0, 1 address(es) available on br-lan
Tue Apr  4 22:06:26 2017 daemon.notice odhcpd[758]: Failed to send to ff02::1%br-lan (Address not available)
Tue Apr  4 22:06:27 2017 kern.info kernel: [   36.860714] br-lan: port 1(eth0) entered forwarding state
Tue Apr  4 22:06:29 2017 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Tue Apr  4 22:06:29 2017 kern.info kernel: [   38.266259] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
Tue Apr  4 22:06:29 2017 kern.info kernel: [   38.536817] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.40
Tue Apr  4 22:06:29 2017 kern.info kernel: [   38.591362] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
Tue Apr  4 22:06:29 2017 kern.info kernel: [   38.614009] device wlan0-1 entered promiscuous mode
Tue Apr  4 22:06:29 2017 daemon.notice hostapd: wlan0-1: interface state UNINITIALIZED->COUNTRY_UPDATE
Tue Apr  4 22:06:29 2017 daemon.err hostapd: Using interface wlan0-1 with hwaddr 00:0c:43:28:60:01 and ssid "LEDE"
Tue Apr  4 22:06:29 2017 daemon.notice hostapd: wlan0-1: interface state COUNTRY_UPDATE->ENABLED
Tue Apr  4 22:06:29 2017 daemon.notice hostapd: wlan0-1: AP-ENABLED
Tue Apr  4 22:06:30 2017 kern.info kernel: [   39.181068] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Tue Apr  4 22:06:30 2017 daemon.notice netifd: radio0 (909): Successfully initialized wpa_supplicant
Tue Apr  4 22:06:31 2017 daemon.notice netifd: Interface 'wwan' is enabled
Tue Apr  4 22:06:31 2017 daemon.notice odhcpd[758]: Got DHCPv6 request
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.426175] wlan0: authenticate with 34:4d:f7:9a:e3:83
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.437156] wlan0: send auth to 34:4d:f7:9a:e3:83 (try 1/3)
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.452507] wlan0: authenticated
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.457010] wlan0: associate with 34:4d:f7:9a:e3:83 (try 1/3)
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.475656] wlan0: RX AssocResp from 34:4d:f7:9a:e3:83 (capab=0x431 status=0 aid=2)
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.482040] wlan0: associated
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.484944] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Tue Apr  4 22:06:32 2017 daemon.notice netifd: Network device 'wlan0' link is up
Tue Apr  4 22:06:32 2017 daemon.notice netifd: Interface 'wwan' has link connectivity
Tue Apr  4 22:06:32 2017 daemon.notice netifd: Interface 'wwan' is setting up now
Tue Apr  4 22:06:32 2017 daemon.notice netifd: wwan (1151): udhcpc: started, v1.25.1
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.802543] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.807943] br-lan: port 2(wlan0-1) entered forwarding state
Tue Apr  4 22:06:32 2017 kern.info kernel: [   41.813205] br-lan: port 2(wlan0-1) entered forwarding state
Tue Apr  4 22:06:32 2017 daemon.notice netifd: Network device 'wlan0-1' link is up
Tue Apr  4 22:06:32 2017 daemon.notice netifd: wwan (1151): udhcpc: sending discover
Tue Apr  4 22:06:32 2017 daemon.notice netifd: wwan (1151): udhcpc: sending select for 192.168.43.15
Tue Apr  4 22:06:32 2017 daemon.notice netifd: wwan (1151): udhcpc: lease of 192.168.43.15 obtained, lease time 7200
Tue Apr  4 22:06:33 2017 daemon.notice netifd: Interface 'wwan' is now up
Tue Apr  4 22:06:33 2017 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Tue Apr  4 22:06:34 2017 daemon.info odhcpd[758]: Initial RA router lifetime 0, 1 address(es) available on br-lan
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: started, version 2.76 cachesize 150
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: DNS service limited to local subnets
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq-dhcp[1199]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: using local addresses only for domain lan
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: reading /tmp/resolv.conf.auto
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: using local addresses only for domain lan
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: using nameserver 192.168.43.1#53
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: read /etc/hosts - 4 addresses
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: read /tmp/hosts/odhcpd - 0 addresses
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq[1199]: read /tmp/hosts/dhcp.cfg02411c - 2 addresses
Tue Apr  4 22:06:34 2017 daemon.info dnsmasq-dhcp[1199]: read /etc/ethers - 0 addresses
Tue Apr  4 22:06:34 2017 kern.info kernel: [   43.816762] br-lan: port 2(wlan0-1) entered forwarding state

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,917

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

W lede nie działa usb, wiele osób to zgłaszało.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez santaclaus21 (edytowany przez santaclaus21 2017-04-05 06:59:31)

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Tak, masz rację. Doszedłem w końcu do tego jedną z komend którą podawałeś w jakimś wątku do pokazywania statusu urządzeń USB, z pamięci nie pamiętam.
Dziś powrót na AA, w BB i CC nie udało mi się ożywić WiFi... Próbowałem opcję z wiki dla bliźniaczego modelu 803A - bez skutku. Przy tutorialu ze sklejaniem plików wysiadłem a i tam się liczy wielkość obrazu która w 803A jest inna - a lutowałem R80 już zbyt wiele razy.. więc nie próbuję, AA może być o ile wszystko zadziała...  smile

Z tym, że w AA też instalowałem większość sterowników i nie miałem /dev/USB... ani nic w logach co by wskazywało na uruchomienie modemu - próbowałem 2 różne HiLinki: ZTE823 i Huawei E3351.

Choć wiem gdzie mogłem zrobić błąd. Nie wiedziałem, że za każdym restartem routera trzeba jak później (na LEDE) zauważyłem zrobić najpierw "opkg update". Myślałem, że jak raz zrobię - system to gdzieś zcachuje a wydaje mi się, że nie i dlatego prawdopodobnie nie zainstalowałem wszystkich sterowników... pisało, że ich nie ma a mogło zabraknąć tylko "opkg update". Zmyliła mnie podobna komenda z linuxa "apt-get update" z tego wyniki są pamiętane i wystarczy wywołać raz na jakiś czas.

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,917

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Po każdym resecie musisz to zrobić jeżeli chcesz coś instalować bo listy z pakietami trzymane są w pamięci ram.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez santaclaus21

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Dobra, jest z powrotem OpenWRT AA, sterowniki według Twojego poradnika odnośnie routera 3G/4G dla AA + ten przy MF823. Ale nie widzę usb0 ani dodatkowego eth. Wybacz - raczkuję w openwrt, modem się przedstawił ogólnie. sad

syslog:
--------------------------
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.172000] TCP: Hash tables configured (established 2048 bind 2048)
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.176000] TCP reno registered
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.188000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.192000] NET: Registered protocol family 1
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.200000] PCI: CLS 0 bytes, default 32
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.200000] gptu: totally 6 16-bit timers/counters
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.204000] gptu: misc_register on minor 63
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.208000] gptu: succeeded to request irq 126
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.212000] gptu: succeeded to request irq 127
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.216000] gptu: succeeded to request irq 128
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.220000] gptu: succeeded to request irq 129
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.228000] gptu: succeeded to request irq 130
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.232000] gptu: succeeded to request irq 131
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.244000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.256000] msgmni has been set to 120
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.260000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.268000] io scheduler noop registered
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.272000] io scheduler deadline registered (default)
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.276000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.284000] console [ttyLTQ1] enabled, bootconsole disabled
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.308000] ltq_nor: Found an alias at 0x800000 for the chip at 0x0
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.308000] Amd/Fujitsu Extended Query Table at 0x0040
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.312000]   Amd/Fujitsu Extended Query version 1.1.
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.316000] number of CFI chips: 1
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.320000] Creating 4 MTD partitions on "ltq_nor":
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.324000] 0x000000000000-0x000000010000 : "uboot"
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.348000] found squashfs behind kernel
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.348000] Creating 2 MTD partitions on "ltq_nor":
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.352000] 0x000000020000-0x00000011857b : "kernel"
Apr  5 13:43:08 OpenWrt kern.warn kernel: [    0.360000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.372000] 0x00000011857b-0x0000007f0000 : "rootfs"
Apr  5 13:43:08 OpenWrt kern.warn kernel: [    0.376000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.392000] mtd: partition "rootfs" set to be root filesystem
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.396000] mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=520000
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.404000] 0x0000002d0000-0x0000007f0000 : "rootfs_data"
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.412000] 0x0000007f0000-0x000000800000 : "board_config"
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.440000] ltq_mii: probed
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.468000] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.476000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=ltq_etop-fffffff:00, irq=-1)
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.488000] Registered led device: soc:blue:power
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: soc:red:internet
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: soc:red:power
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: soc:red:wps
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: soc:red:fxo
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.492000] Registered led device: soc:green:usb
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.496000] Registered led device: soc:green:wifi
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.496000] Registered led device: soc:green:wifi1
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.496000] Registered led device: soc:blue:wifi
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.496000] Registered led device: soc:blue:wifi1
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.496000] Registered led device: soc:green:eth1
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.496000] Registered led device: soc:green:eth2
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.500000] Registered led device: soc:green:eth3
Apr  5 13:43:08 OpenWrt kern.debug kernel: [    0.500000] Registered led device: soc:green:eth4
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.500000] TCP cubic registered
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.500000] NET: Registered protocol family 17
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    0.508000] Bridge firewalling registered
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.508000] 8021q: 802.1Q VLAN Support v1.8
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.532000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Apr  5 13:43:08 OpenWrt kern.info kernel: [    0.540000] Freeing unused kernel memory: 176k freed
Apr  5 13:43:08 OpenWrt kern.notice kernel: [    7.656000] JFFS2 notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 6 of xref (0 dead, 2 orphan) found.
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.460000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.464000] Backport based on wireless-testing.git master-2012-09-07
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.512000] cfg80211: Calling CRDA to update world regulatory domain
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.516000] cfg80211: World regulatory domain updated:
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.520000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.528000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.536000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.544000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.552000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   10.556000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   11.348000] usbcore: registered new interface driver usbfs
Apr  5 13:43:08 OpenWrt kern.info kernel: [   11.352000] usbcore: registered new interface driver hub
Apr  5 13:43:08 OpenWrt kern.info kernel: [   11.360000] usbcore: registered new device driver usb
Apr  5 13:43:08 OpenWrt kern.warn kernel: [   11.940000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
Apr  5 13:43:08 OpenWrt kern.debug kernel: [   11.944000] rt2800pci 0000:00:0e.0: setting latency timer to 64
Apr  5 13:43:08 OpenWrt kern.debug kernel: [   12.116000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Apr  5 13:43:08 OpenWrt kern.debug kernel: [   12.120000] Registered led device: rt2800pci-phy0::radio
Apr  5 13:43:08 OpenWrt kern.debug kernel: [   12.120000] Registered led device: rt2800pci-phy0::assoc
Apr  5 13:43:08 OpenWrt kern.debug kernel: [   12.120000] Registered led device: rt2800pci-phy0::quality
Apr  5 13:43:08 OpenWrt kern.info kernel: [   12.280000] NET: Registered protocol family 20
Apr  5 13:43:08 OpenWrt kern.info kernel: [   12.460000] Button Hotplug driver version 0.4.1
Apr  5 13:43:08 OpenWrt kern.info kernel: [   12.604000] PPP generic driver version 2.4.2
Apr  5 13:43:08 OpenWrt kern.info kernel: [   13.104000] ip_tables: (C) 2000-2006 Netfilter Core Team
Apr  5 13:43:08 OpenWrt kern.info kernel: [   13.424000] NET: Registered protocol family 24
Apr  5 13:43:08 OpenWrt kern.info kernel: [   13.524000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Apr  5 13:43:08 OpenWrt kern.info kernel: [   13.684000] nf_conntrack version 0.5.0 (966 buckets, 3864 max)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   14.144000] IFX MEI Version 5.00.00
Apr  5 13:43:08 OpenWrt kern.warn kernel: [   14.308000]
Apr  5 13:43:08 OpenWrt kern.warn kernel: [   14.308000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
Apr  5 13:43:08 OpenWrt kern.info kernel: [   14.344000]     ATM (A1) firmware version 1.0.19
Apr  5 13:43:08 OpenWrt kern.warn kernel: [   14.348000] ifxmips_atm: ATM init succeed
Apr  5 13:43:08 OpenWrt kern.info kernel: [   14.380000] dwc_otg: version 2.60a 22-NOV-2006
Apr  5 13:43:08 OpenWrt kern.info kernel: [   14.988000] DWC_otg: Using DMA mode
Apr  5 13:43:08 OpenWrt kern.info kernel: [   14.988000] dwc_otg dwc_otg.0: DWC OTG Controller
Apr  5 13:43:08 OpenWrt kern.info kernel: [   14.996000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.000000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.012000] DWC_otg: Init: Port Power? op_state=1
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.020000] hub 1-0:1.0: 1 port detected
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.156000] usbcore: registered new interface driver usbserial
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.160000] USB Serial support registered for generic
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.164000] usbcore: registered new interface driver usbserial_generic
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.168000] usbserial: USB Serial Driver core
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.200000] usbcore: registered new interface driver cdc_ether
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.328000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.376000] usbcore: registered new interface driver rndis_host
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.428000] usb 1-1: new high-speed USB device number 2 using dwc_otg
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.504000] USB Serial support registered for GSM modem (1-port)
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.508000] usbcore: registered new interface driver option
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.512000] option: v0.7.2:USB Driver for GSM modems
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.624000] hub 1-1:1.0: USB hub found
Apr  5 13:43:08 OpenWrt kern.info kernel: [   15.632000] hub 1-1:1.0: 4 ports detected
Apr  5 13:43:11 OpenWrt user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_dwc_otg_hcd Product=DWC_OTG_Controller Serial=dwc_otg.0
Apr  5 13:43:12 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=? Serial=?
Apr  5 13:43:14 OpenWrt kern.info kernel: [   23.372000] usb 1-1.3: new high-speed USB device number 3 using dwc_otg
Apr  5 13:43:16 OpenWrt user.notice usb-modeswitch: 1-1.3:1.0: Manufacturer=ZTE,Incorporated Product=ZTE_WCDMA_Technologies_MSM Serial=MF8230ZTED010000
Apr  5 13:43:18 OpenWrt user.info sysinit: Command failed: Not found
Apr  5 13:43:19 OpenWrt kern.info kernel: [   28.444000] device eth0 entered promiscuous mode
Apr  5 13:43:19 OpenWrt kern.info kernel: [   28.456000] br-lan: port 1(eth0) entered forwarding state
Apr  5 13:43:19 OpenWrt kern.info kernel: [   28.460000] br-lan: port 1(eth0) entered forwarding state
Apr  5 13:43:19 OpenWrt daemon.notice netifd: Interface 'lan' is now up
Apr  5 13:43:19 OpenWrt daemon.notice netifd: Interface 'loopback' is now up
Apr  5 13:43:19 OpenWrt user.info sysinit: Configuration file: /var/run/hostapd-phy0.conf
Apr  5 13:43:19 OpenWrt user.info sysinit: nl80211: Failed to add interface wlan0 into bridge eth0: Operation not supported
Apr  5 13:43:19 OpenWrt user.info sysinit: nl80211 driver initialization failed.
Apr  5 13:43:19 OpenWrt user.info sysinit: Failed to start hostapd for phy0
Apr  5 13:43:21 OpenWrt kern.info kernel: [   30.464000] br-lan: port 1(eth0) entered forwarding state
Apr  5 13:43:22 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Apr  5 13:43:25 OpenWrt user.info sysinit: Loading defaults
Apr  5 13:43:26 OpenWrt user.info sysinit: Loading synflood protection
Apr  5 13:43:26 OpenWrt user.info sysinit: Adding custom chains
Apr  5 13:43:28 OpenWrt user.info sysinit: Loading zones
Apr  5 13:43:31 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Apr  5 13:43:32 OpenWrt user.info sysinit: Loading forwardings
Apr  5 13:43:32 OpenWrt user.info sysinit: Loading rules
Apr  5 13:43:32 OpenWrt user.info sysinit: Loading redirects
Apr  5 13:43:32 OpenWrt user.info sysinit: Loading includes
Apr  5 13:43:32 OpenWrt user.info sysinit: Optimizing conntrack
Apr  5 13:43:32 OpenWrt user.info sysinit: Loading interfaces
Apr  5 13:43:33 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Apr  5 13:43:36 OpenWrt authpriv.info dropbear[1023]: Running in background
Apr  5 13:43:40 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Apr  5 13:43:40 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: started, version 2.62 cachesize 150
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCP, IP range 192.168.4.100 -- 192.168.4.249, lease time 12h
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: using local addresses only for domain lan
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: reading /tmp/resolv.conf.auto
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: using nameserver 8.8.8.8#53
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: using local addresses only for domain lan
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq[1077]: read /etc/hosts - 1 addresses
Apr  5 13:43:43 OpenWrt daemon.info dnsmasq-dhcp[1077]: read /etc/ethers - 0 addresses
Apr  5 13:46:39 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCPDISCOVER(br-lan) f8:1a:67:83:06:c9
Apr  5 13:46:39 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCPOFFER(br-lan) 192.168.4.153 f8:1a:67:83:06:c9
Apr  5 13:46:39 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCPREQUEST(br-lan) 192.168.4.153 f8:1a:67:83:06:c9
Apr  5 13:46:39 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCPACK(br-lan) 192.168.4.153 f8:1a:67:83:06:c9
Apr  5 13:46:45 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCPREQUEST(br-lan) 192.168.4.186 68:a3:c4:0f:14:12
Apr  5 13:46:45 OpenWrt daemon.info dnsmasq-dhcp[1077]: DHCPACK(br-lan) 192.168.4.186 68:a3:c4:0f:14:12 wojtek-Lenovo-G570

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,917

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Failed to add interface wlan0 into bridge eth0: Operation not supported <- coś masz źle w konfigu. Pokaż

cat /proc/bus/usb/devices

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez santaclaus21

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

eth0 chyba bez znaczenia bo to jest wbudowana karta w routerze. Konfig nie jest dopracowany, jest oryginalny, ustawiłem tylko wifi + lan.

-----

root@OpenWrt:~# cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 dwc_otg_hcd
S:  Product=DWC OTG Controller
S:  SerialNumber=dwc_otg.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=02 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=2514 Rev= 0.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=01 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=02 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1405 Rev=f0.70
S:  Manufacturer=ZTE,Incorporated
S:  Product=ZTE WCDMA Technologies MSM
S:  SerialNumber=MF8230ZTED000000
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,917

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Masz sterownik. Żadne ethX nie pojawiło się dodatkowe?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez santaclaus21

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Problem w tym, że nie. Być może jakieś sterowniki robią konflikt. Sterowników nie konfigurowałem bo nie znam się na tym. Tylko instalowałem jak popadło. Dodam, że MF823 to HiLink - nie wiem czy wszystkie są tego typu.

1) według wątka https://eko.one.pl/?p=openwrt-3g
opkg update
opkg install kmod-usb-core kmod-usb2 kmod-usb-serial kmod-usb-serial-option usb-modeswitch usb-modeswitch-data libusb
opkg install chat comgt
opkg install kmod-usb-net-rndis

2) oraz według wątka https://eko.one.pl/forum/viewtopic.php?id=10165&p=2
opkg install kmod-scsi-core kmod-usb-storage kmod-usb-net-cdc-ether kmod-usb-net

Brak nowych eth, brak usb0 itp.

------config sieci aktualny-------

root@OpenWrt:~# vi /etc/config/network

config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config interface 'lan'
        option ifname 'eth0'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.4.188'
        option netmask '255.255.255.0'
        option gateway '192.168.4.1'
        option dns '8.8.8.8'

config adsl-device 'adsl'
        option fwannex 'b'
        option annex 'b2p'

config atm-bridge 'atm'
        option unit '0'
        option vpi '1'
        option vci '32'
        option encaps 'llc'
        option payload 'bridged'

config interface 'wan'
        option ifname 'nas0'
        option proto 'pppoe'
        option username 'foo'
        option password 'bar'

config interface 'wifi'
        option proto 'static'


-----------dev--------------
root@OpenWrt:~# cd /dev
root@OpenWrt:/dev# ls
bus          log          mtd3         mtdblock0    port         urandom
console      mem          mtd3ro       mtdblock1    ppp          watchdog
dsl_cpe_api  mtd0         mtd4         mtdblock2    ptmx         zero
full         mtd0ro       mtd4ro       mtdblock3    pts
gptu         mtd1         mtd5         mtdblock4    random
ifx_mei      mtd1ro       mtd5ro       mtdblock5    shm
input        mtd2         mtd6         mtdblock6    tty
kmsg         mtd2ro       mtd6ro       null         ttyLTQ1

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 115,917

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

ifconfig -a

pokaż

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez santaclaus21 (edytowany przez santaclaus21 2017-04-05 21:45:50)

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Nie ma nic nowego niż było przed instalacją modemu. Patrzyłem tam, prześlę jak siąde do komputera. Mogę przełączyć na tryb modemu, ale nie wiem czy to da się cofnąć więc nie próbuje.

------------ifconfig -a------------
br-lan    Link encap:Ethernet  HWaddr 00:23:08:FD:42:AC
          inet addr:192.168.4.188  Bcast:192.168.4.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3923 errors:0 dropped:703 overruns:0 frame:0
          TX packets:2238 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:311807 (304.4 KiB)  TX bytes:529565 (517.1 KiB)

eth0      Link encap:Ethernet  HWaddr 00:23:08:FD:42:AC
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:47 errors:0 dropped:0 overruns:0 frame:0
          TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4718 (4.6 KiB)  TX bytes:4718 (4.6 KiB)

wlan0     Link encap:Ethernet  HWaddr 0C:00:28:43:00:60
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:32
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


-----------uFFFFF----------
zresetowałem urządzenie, wsadziłem modem Huaweii 3372 Hilink - pojawiło się eth1 oraz USB0, wsadziłem z powrotem modem ZTE MF823 - tym razem z kartą NJU (mój główny internet) zamiast Aero2 restart.

Jesteśmy w domu. USB0 się pojawiło smile jeszcze nie mogę odpalić samego internetu, ale myślę, że sobie poradzę - jeśli nie to na pewno się odezwę.

Pozostał tylko problem z wszystkimi świecącymi LEDami na fronce routera. W BB i CC gasły - niestety tam był problem albo z USB albo z Wifi.
Może ktoś będzie wiedział jak je skonfigurować lub wyłączyć.... Dzięki Cezary!

12 Odpowiedź przez santaclaus21

  • Zarejestrowany: 2014-04-01
  • Posty: 85

Odp: Vodafone 802 - OpenWRT AA, instalacja modemu HILINK (MF823)

Obsługę ledów znalazłem w luci.
Jeśli chodzi o sam modem... fakt uruchomiłem go, ale po przesłaniu pierwszych 40kB transfer się zawiesił (!). Żaden restart nie pomaga. Albo ja jestem za głupi na ten router albo jest on strasznie problematyczny. Dziś minie tydzień jak zacząłem wgrywać (wieczorami) do niego OpenWrt. Konfiguracja posiadanego TPLinka (3220v2) zajęła mi niegdyś.. chyba kilka/naście minut.

Odinstalowałem pakiety od modemu, dziś restart OpenWRT do ustawień fabrycznych i później ostatnie podejście. Następnie allegro lub kosz. Mam powoli dość...