Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Pomocy - TP-Link MR3420v2 + modem Huawei e3373 + mało pamięci
Strony Poprzednia 1 2 3 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Już to czytałem chyba z 50 razy w wielorakie strony 
Mam wyjąć modem przed wydaniem poleceń? ?Kartę z modemu? Kiedy mam włożyć wobec tego modem do routera (kartę pamięci do czytnika w routerze)?
Po co masz wymować/wkładać modem kiedykolwiek? W opisie nic nie ma o wyjmowaniu modemu. Karta do modemu, modem do routera i robisz extroota. Czytnika kart do tego nie potrzebujesz.
Choć lepiej by było gdybyś podłączył hub usb do routera (i tak do tego modemu go powinieneś mieć) i zrobić extroota normalnie na pendrive.
No też mi się tak wydawało z tym wyjmowaniem modemu albo karty.
Więc dlaczego byłeś uprzejmy napisać, że robię extroota na karcie pamięci a to błąd?
Robiłem to wg opisu.
Najpierw na systemie plików
/dev/mtdblock3 384.0K 320.0K 64.0K 83% /overlay
overlayfs:/overlay 384.0K 320.0K 64.0K 83% /
robiłem extroota wg opisu.
Po reboocie dostawałem 1.8GB. Doinstalowywałem sterowniki cdc-ether ale logread | grep cdc podawał informację bez oznaczenia interfejsu. I wtedy instalowałem pakiet usb-modeswitch, który rozwalał extroota 
Bo taki extroot jest wybitnie seksualny i piep* przy każdej możliwej sytuacji.
Nie możesz instalować usb-modeswitch na extroocie, poradnik był inaczej napisany. Albo robisz tak jak to napisałem albo nie będzie Ci działać bo nie przełączysz modemu.
Czy chodzi o to, że po extroocie modem powinien być już przełączony i nie powinno być konieczności instalacji usb-modeswitch?
Jeśli tak, to coś u mnie jest nie tak.
Robienie extroota idzie ok, ale usb-modeswitch nie przełącza modemu. Modem zgłasza się tak, jak to opisałeś, że zgłasza się bez przełączenia:
root@OpenWrt:/# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
To jest po reboocie na extroocie
Co mam zrobić, aby modem przełączył się poprawnie?
Sama instalacja usb-modeswitch przełącza modem w poprawny stan.
Po reboocie jest tak samo. Może nie powinienem używać usbmode w skrypcie z block?
Zrobiłeś ten skrypt do przełączania? Przez i po wywołaniu usbmode wstaw sobie cat /sys/kernel/debug/usb/devices >> /tmp/log.txt i zobacz co w nim jest
Oczywiście że zrobiłem kolejno krok po kroku wg tutoriala
Na extroocie nie ma pliku /tmp/log.txt
Skrypt się nie uruchamia???
root@OpenWrt:/# ls /sbin/bl*
/sbin/block
Jest tam po reboocie tylko oryginalny /sbin/block...
Zrobiłem ten skrypt na extroocie.
cat /tmp/log.txt
root@OpenWrt:/# cat /tmp/log.txt
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1f01 Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Ten skrypt mam zrobić na extroocie czy we flashu? Bo w tutorialu napisałeś, że ma być przed rebootem. Może on dwa razy zmienia ten tryb modemu - raz we flashu a raz na extroot, dlatego tak jest?
Ten skrypt ma być we flashu, na extroocie nie ma najmniejszego sensu. I tak jest w poradniku - jest robiony PRZED zrobieniem extroota.
Czyli mam zrobić ten skrypt bez robienia extroota, reboot i odczytać log? Bo jak mam odczytać /tmp/log.txt jak po reboocie mam extroot?
Spróbuję zrobić to bez podmiany danych we fstab i zobaczę log. Dobrze?
Bo /tmp jest w pamięci tam a nie w extroocie. Więc plik tam położony będzie zawsze, nie zależnie od tego czy masz extroota czy nie.
W takim razie coś było nie tak, bo bez zrobienia skryptu na extroot nie było pliku log.txt w /tmp
Zrobię jeszcze raz. Uparty jestem...
Ehh, jeszcze raz. Zrobienie pliku na extroota jest bez sensu. We flash ma być, bo on się wykonuje przez podmontowaniem nośnika. Jak grochem o ścianę cały czas...
No to tak zrobię. Zrobię ten plik na /sbin przed extrootem.
Tak robiłem. Ściśle wg tuta który podałeś. Zrobiłem wszystko na FLASH, następował reboot i już na extroot polecenie
cat /tmp/log.txt jak kazałeś nic nie dawało, bo pliku log.txt nie było w /tmp.
Skrypt we flash wyglądał tak:
#!/bin/sh
cat /sys/kernel/debug/usb/devices >> /tmp/log.txt
/tmp/overlay/sbin/usbmode -s -c /tmp/overlay/etc/usb-mode.json
cat /sys/kernel/debug/usb/devices >> /tmp/log.txt
for i in 1 2 3 4 5 6 7 8 9 10; do
[ -e /dev/sda1 ] && break
sleep 1
done
exec /sbin/block_/block $*
Zrobiłem sysupgrade -n i zrobię jeszcze raz tylko mi dziewczyna modem odda bo Voice of Poland musi oglądać 
Uruchom router bez modemu/extroota i jak się uruchomi pokaż wyniki poleceń:
ls -al /sbin/block
ls -al /sbin/block_/block
cat /sbin/block
root@OpenWrt:~# ls -al /sbin/block
-rwxr-xr-x 1 root root 277 Oct 29 21:56 /sbin/block
root@OpenWrt:~# ls -al /sbin/block_/block
-rwxr-xr-x 1 root root 19448 Jul 9 07:44 /sbin/block_/block
root@OpenWrt:~# cat /sbin/block
#!/bin/sh
cat /sys/kernel/debug/usb/devices >> /tmp/log.txt
/tmp/overlay/sbin/usbmode -s -c /tmp/overlay/etc/usb-mode.json
cat /sys/kernel/debug/usb/devices >> /tmp/log.txt
for i in 1 2 3 4 5 6 7 8 9 10; do
[ -e /dev/sda1 ] && break
sleep 1
done
exec /sbin/block_/block $*
Dodaj jako drugą linię
logger "tu bylem"
Włóż modem zresetuj. I później patrz w logach czy masz ten komunikat.
Zrobiłem jak kazałeś. Czekam na koniec tego wycia i włożę modem, pokażę po reboocie co się dzieje.
Włożyłem modem do slotu USB
nie robiłem restartu
z ciekawości zrobiłem logread
Sat Jul 9 08:06:12 2016 user.emerg syslog: setting up led WLAN
Sat Jul 9 08:06:12 2016 user.emerg syslog: setting up led USB
Sat Jul 9 08:06:12 2016 daemon.info procd: - init complete -
Sat Oct 29 21:58:30 2016 kern.notice kernel: [ 68.980000] random: nonblocking pool is initialized
Sat Oct 29 21:59:17 2016 authpriv.info dropbear[1381]: Child connection from 192.168.1.136:51138
Sat Oct 29 21:59:17 2016 daemon.info dnsmasq-dhcp[1110]: DHCPINFORM(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Oct 29 21:59:17 2016 daemon.info dnsmasq-dhcp[1110]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Sat Oct 29 21:59:23 2016 authpriv.notice dropbear[1381]: Password auth succeeded for 'root' from 192.168.1.136:51138
Sat Oct 29 22:01:12 2016 daemon.info dnsmasq-dhcp[1110]: DHCPINFORM(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Oct 29 22:01:12 2016 daemon.info dnsmasq-dhcp[1110]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Sat Oct 29 22:11:14 2016 daemon.info dnsmasq-dhcp[1110]: DHCPINFORM(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Oct 29 22:11:14 2016 daemon.info dnsmasq-dhcp[1110]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Sat Oct 29 22:16:23 2016 kern.info kernel: [ 1141.960000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sat Oct 29 22:16:23 2016 kern.info kernel: [ 1142.110000] usb-storage 1-1:1.0: USB Mass Storage device detected
Sat Oct 29 22:16:23 2016 kern.info kernel: [ 1142.130000] scsi host0: usb-storage 1-1:1.0
Sat Oct 29 22:16:24 2016 kern.info kernel: [ 1142.540000] usb 1-1: USB disconnect, device number 2
Sat Oct 29 22:16:24 2016 kern.info kernel: [ 1143.060000] usb 1-1: new high-speed USB device number 3 using ehci-platform
Sat Oct 29 22:16:24 2016 kern.info kernel: [ 1143.210000] usb-storage 1-1:1.2: USB Mass Storage device detected
Sat Oct 29 22:16:24 2016 kern.info kernel: [ 1143.230000] scsi host1: usb-storage 1-1:1.2
Sat Oct 29 22:16:25 2016 kern.notice kernel: [ 1144.230000] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
Sat Oct 29 22:16:25 2016 kern.notice kernel: [ 1144.240000] sd 1:0:0:0: [sda] 3842048 512-byte logical blocks: (1.96 GB/1.83 GiB)
Sat Oct 29 22:16:25 2016 kern.notice kernel: [ 1144.250000] sd 1:0:0:0: [sda] Write Protect is off
Sat Oct 29 22:16:25 2016 kern.debug kernel: [ 1144.250000] sd 1:0:0:0: [sda] Mode Sense: 0f 00 00 00
Sat Oct 29 22:16:25 2016 kern.notice kernel: [ 1144.250000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sat Oct 29 22:16:25 2016 kern.info kernel: [ 1144.270000] sda: sda1
Sat Oct 29 22:16:25 2016 kern.notice kernel: [ 1144.290000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Sat Oct 29 22:16:25 2016 user.notice root: tu bylem
Sat Oct 29 22:16:26 2016 user.notice root: tu bylem
Sat Oct 29 22:21:16 2016 daemon.info dnsmasq-dhcp[1110]: DHCPINFORM(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Oct 29 22:21:16 2016 daemon.info dnsmasq-dhcp[1110]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Czyli skrypt uruchomił się podczas włożenia modemu dwa razy...
Po reboocie:
(...)
Sat Jul 9 08:06:09 2016 daemon.notice netifd: Network device 'wlan0' link is up
Sat Jul 9 08:06:09 2016 daemon.notice netifd: Interface 'wan' has link connectivity
Sat Jul 9 08:06:09 2016 daemon.notice netifd: Interface 'wan' is setting up now
Sat Jul 9 08:06:09 2016 kern.info kernel: [ 35.370000] wlan0: RX AssocResp from 00:03:7e:e7:ca:5a (capab=0x431 status=0 aid=1)
Sat Jul 9 08:06:09 2016 kern.info kernel: [ 35.380000] wlan0: associated
Sat Jul 9 08:06:09 2016 daemon.notice netifd: wan (1344): udhcpc (v1.23.2) started
Sat Jul 9 08:06:10 2016 user.notice root: tu bylem
Sat Jul 9 08:06:10 2016 daemon.info procd: - init complete -
Sat Jul 9 08:06:10 2016 daemon.notice netifd: wan (1344): Sending discover...
(...)
Czyli skrypt się uruchamia.
Ostatnie linie log.txt:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=14dc Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=2ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.36 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=02(comm.) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=14dc Rev= 1.02
S: Manufacturer=HUAWEI_MOBILE
S: Product=HUAWEI_MOBILE
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=2ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
Czyli modem jest w dobrym stanie (przełączony).
Mam zmieniać linie /etc/config/fstab i spróbować zrobić extroota?
Tak.
Niestety. Po wydaniu komend:
# /sbin/block_/block detect > /etc/config/fstab
# uci set fstab.@mount[0].target='/overlay'
# uci set fstab.@mount[0].enabled='1'
# uci commit
i reboocie nie ma Tu bylem w logach, a modem się nie przełącza.
Więc zrób extroota normalnie na pendrive.
Jak rozumieć na pendrive? Chodzi Ci o to by modem podczas robienia był w slocie USB? Bo mnie nie urządza pendrive. Chodzi mi o to, bym miał połączenie LTE z modemu, które router udostępnia w domu przez WiFi, a jednocześnie by na karcie microSD w modemie było miejsce na OpenVPN. Czyli modem i jego karta nie są w routerze z przypadku.
Po sysupgrade kolejnym i ustawieniu wszystkiego z modemem w porcie to samo.
Oto logread:
root@OpenWrt:~# logread
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 8037c2b0, node_mem_map 81000000
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] Normal zone: 8192 pages, LIFO batch:0
Sat Jul 9 07:45:49 2016 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sat Jul 9 07:45:49 2016 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Sat Jul 9 07:45:49 2016 kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.000000] Kernel command line: board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Sat Jul 9 07:45:49 2016 kern.warn kernel: [ 0.000000] Memory: 28324K/32768K available (2606K kernel code, 128K rwdata, 544K rodata, 232K init, 193K bss, 4444K reserved)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] NR_IRQS:51
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.100000] NET: Registered protocol family 16
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.100000] MIPS: machine is TP-LINK TL-MR3420 v2
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.560000] Switched to clocksource MIPS
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.560000] NET: Registered protocol family 2
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.570000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.580000] TCP: Hash tables configured (established 1024 bind 1024)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.590000] TCP: reno registered
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.600000] NET: Registered protocol family 1
Sat Jul 9 07:45:49 2016 kern.debug kernel: [ 0.610000] PCI: CLS 0 bytes, default 32
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.610000] futex hash table entries: 256 (order: -1, 3072 bytes)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.650000] msgmni has been set to 55
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.660000] io scheduler noop registered
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.670000] io scheduler deadline registered (default)
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.670000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.680000] console [ttyS0] disabled
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.710000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.710000] console [ttyS0] enabled
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.720000] bootconsole [early0] disabled
Sat Jul 9 07:45:49 2016 kern.warn kernel: [ 0.730000] m25p80 spi0.0: found s25sl032p, expected m25p80
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.740000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.740000] 5 tp-link partitions found on MTD device spi0.0
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.750000] Creating 5 MTD partitions on "spi0.0":
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.750000] 0x000000000000-0x000000020000 : "u-boot"
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.760000] 0x000000020000-0x000000141ac0 : "kernel"
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.770000] 0x000000141ac0-0x0000003f0000 : "rootfs"
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.770000] mtd: device 2 (rootfs) set to be root filesystem
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.780000] 1 squashfs-split partitions found on MTD device rootfs
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.780000] 0x000000390000-0x0000003f0000 : "rootfs_data"
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.790000] 0x0000003f0000-0x000000400000 : "art"
Sat Jul 9 07:45:49 2016 kern.notice kernel: [ 0.800000] 0x000000020000-0x0000003f0000 : "firmware"
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 0.830000] libphy: ag71xx_mdio: probed
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 1.420000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
Sat Jul 9 07:45:49 2016 kern.info kernel: [ 1.430000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.020000] ag71xx-mdio.1: Found an AR934X built-in switch
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.060000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.070000] TCP: cubic registered
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.070000] NET: Registered protocol family 17
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.080000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 2.090000] Bridge firewalling registered
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.090000] 8021q: 802.1Q VLAN Support v1.8
Sat Jul 9 07:45:50 2016 kern.err kernel: [ 2.100000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.110000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 2.120000] Freeing unused kernel memory: 232K (80396000 - 803d0000)
Sat Jul 9 07:45:50 2016 user.info kernel: [ 3.180000] init: Console is alive
Sat Jul 9 07:45:50 2016 user.info kernel: [ 3.190000] init: - watchdog -
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.870000] usbcore: registered new interface driver usbfs
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.870000] usbcore: registered new interface driver hub
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.880000] usbcore: registered new device driver usb
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 4.930000] SCSI subsystem initialized
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.940000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.950000] ehci-platform: EHCI generic platform driver
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.950000] ehci-platform ehci-platform: EHCI Host Controller
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.960000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.970000] ehci-platform ehci-platform: TX-TX IDP fix enabled
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 4.980000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 5.000000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 5.000000] hub 1-0:1.0: USB hub found
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 5.010000] hub 1-0:1.0: 1 port detected
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 5.010000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 5.020000] ohci-platform: OHCI generic platform driver
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 5.030000] usbcore: registered new interface driver usb-storage
Sat Jul 9 07:45:50 2016 user.info kernel: [ 5.250000] init: - preinit -
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 5.880000] random: procd urandom read with 9 bits of entropy available
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 7.460000] eth1: link up (1000Mbps/Full duplex)
Sat Jul 9 07:45:50 2016 user.info kernel: [ 9.210000] mount_root: loading kmods from internal overlay
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 9.540000] jffs2: notice: (391) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Sat Jul 9 07:45:50 2016 user.info kernel: [ 9.560000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Sat Jul 9 07:45:50 2016 user.info kernel: [ 9.570000] block: extroot: device not present, retrying in 5 seconds
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 10.070000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 10.220000] usb-storage 1-1:1.0: USB Mass Storage device detected
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 10.220000] scsi host0: usb-storage 1-1:1.0
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 11.230000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 11.240000] scsi 0:0:0:1: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 11.250000] sd 0:0:0:1: [sda] 3841911 512-byte logical blocks: (1.96 GB/1.83 GiB)
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 11.260000] sd 0:0:0:1: [sda] Write Protect is off
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 11.260000] sd 0:0:0:1: [sda] Mode Sense: 0f 00 00 00
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 11.260000] sd 0:0:0:1: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 11.280000] sda: unknown partition table
Sat Jul 9 07:45:50 2016 kern.notice kernel: [ 11.290000] sd 0:0:0:1: [sda] Attached SCSI removable disk
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 14.590000] EXT4-fs (sda): mounted filesystem with ordered data mode. Opts:
Sat Jul 9 07:45:50 2016 user.notice kernel: [ 14.610000] mount_root: switched to extroot
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 14.640000] eth1: link down
Sat Jul 9 07:45:50 2016 user.info kernel: [ 14.650000] procd: - early -
Sat Jul 9 07:45:50 2016 user.info kernel: [ 14.660000] procd: - watchdog -
Sat Jul 9 07:45:50 2016 user.info kernel: [ 15.470000] procd: - ubus -
Sat Jul 9 07:45:50 2016 user.info kernel: [ 16.480000] procd: - init -
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.320000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.330000] Backport generated by backports.git backports-20151218-0-g2f58d9d
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.340000] nf_conntrack version 0.5.0 (446 buckets, 1784 max)
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.390000] xt_time: kernel timezone is -0000
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.440000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.510000] PPP generic driver version 2.4.2
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.510000] NET: Registered protocol family 24
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.580000] ath: EEPROM regdomain: 0x0
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.580000] ath: EEPROM indicates default country code should be used
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.580000] ath: doing EEPROM country->regdmn map search
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.580000] ath: country maps to regdmn code: 0x3a
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.580000] ath: Country alpha2 being used: US
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.580000] ath: Regpair used: 0x3a
Sat Jul 9 07:45:50 2016 kern.debug kernel: [ 17.590000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sat Jul 9 07:45:50 2016 kern.info kernel: [ 17.590000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47
Sat Jul 9 07:45:51 2016 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Sat Jul 9 07:45:51 2016 user.emerg syslog: 'radio0' is disabled
Sat Jul 9 07:45:51 2016 user.emerg syslog: 'radio0' is disabled
Sat Jul 9 07:45:51 2016 daemon.err block: /dev/sda is already mounted
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led WAN
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led LAN1
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led LAN2
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led LAN3
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led LAN4
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led WLAN
Sat Jul 9 07:45:53 2016 user.emerg syslog: setting up led USB
Sat Jul 9 07:45:53 2016 kern.notice kernel: [ 27.150000] random: nonblocking pool is initialized
Sat Jul 9 07:45:54 2016 daemon.info procd: - init complete -
Sat Jul 9 07:45:55 2016 kern.info kernel: [ 29.070000] device eth1 entered promiscuous mode
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'lan' is enabled
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'lan' is setting up now
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'lan' is now up
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'loopback' is enabled
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'loopback' is setting up now
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'loopback' is now up
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'wan' is enabled
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'wan6' is enabled
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Network device 'lo' link is up
Sat Jul 9 07:45:55 2016 daemon.notice netifd: Interface 'loopback' has link connectivity
Sat Jul 9 07:45:56 2016 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sat Jul 9 07:45:57 2016 kern.info kernel: [ 30.710000] eth1: link up (1000Mbps/Full duplex)
Sat Jul 9 07:45:57 2016 kern.info kernel: [ 30.730000] br-lan: port 1(eth1) entered forwarding state
Sat Jul 9 07:45:57 2016 kern.info kernel: [ 30.730000] br-lan: port 1(eth1) entered forwarding state
Sat Jul 9 07:45:57 2016 daemon.notice netifd: Network device 'eth1' link is up
Sat Jul 9 07:45:57 2016 daemon.notice netifd: Bridge 'br-lan' link is up
Sat Jul 9 07:45:57 2016 daemon.notice netifd: Interface 'lan' has link connectivity
Sat Jul 9 07:45:59 2016 kern.info kernel: [ 32.730000] br-lan: port 1(eth1) entered forwarding state
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq[1120]: started, version 2.73 cachesize 150
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq[1120]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq[1120]: DNS service limited to local subnets
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq-dhcp[1120]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq[1120]: using local addresses only for domain lan
Sat Jul 9 07:46:00 2016 daemon.warn dnsmasq[1120]: no servers found in /tmp/resolv.conf.auto, will retry
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq[1120]: read /etc/hosts - 1 addresses
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq[1120]: read /tmp/hosts/dhcp - 1 addresses
Sat Jul 9 07:46:00 2016 daemon.info dnsmasq-dhcp[1120]: read /etc/ethers - 0 addresses
Sat Jul 9 07:46:02 2016 daemon.info dnsmasq-dhcp[1120]: DHCPREQUEST(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Jul 9 07:46:02 2016 daemon.info dnsmasq-dhcp[1120]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Sat Jul 9 07:46:06 2016 daemon.info dnsmasq-dhcp[1120]: DHCPINFORM(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Jul 9 07:46:06 2016 daemon.info dnsmasq-dhcp[1120]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Sat Jul 9 07:46:34 2016 authpriv.info dropbear[1265]: Not backgrounding
Sat Jul 9 07:46:37 2016 authpriv.info dropbear[1270]: Child connection from 192.168.1.136:51488
Sat Jul 9 07:46:49 2016 authpriv.warn dropbear[1270]: User 'root' has blank password, rejected
Sat Jul 9 07:46:52 2016 authpriv.warn dropbear[1270]: User 'root' has blank password, rejected
Sat Jul 9 07:46:58 2016 authpriv.warn dropbear[1270]: User 'root' has blank password, rejected
Sat Jul 9 07:47:05 2016 authpriv.info dropbear[1270]: Exit before auth (user 'root', 3 fails): Exited normally
Sat Jul 9 07:47:16 2016 authpriv.info dropbear[1271]: Child connection from 192.168.1.136:51489
Sat Jul 9 07:47:23 2016 authpriv.warn dropbear[1271]: User 'root' has blank password, rejected
Sat Jul 9 07:47:23 2016 daemon.info dnsmasq-dhcp[1120]: DHCPINFORM(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86
Sat Jul 9 07:47:23 2016 daemon.info dnsmasq-dhcp[1120]: DHCPACK(br-lan) 192.168.1.136 00:1f:c6:e9:f2:86 AFTERMachine
Sat Jul 9 07:47:25 2016 authpriv.info dropbear[1271]: Exit before auth (user 'root', 1 fails): Exited normally
Sat Jul 9 07:47:44 2016 auth.info passwd: Password for root changed by root
Sat Jul 9 07:48:06 2016 authpriv.info dropbear[1335]: Child connection from 192.168.1.136:51491
Sat Jul 9 07:48:12 2016 authpriv.notice dropbear[1335]: Password auth succeeded for 'root' from 192.168.1.136:51491
root@OpenWrt:~#
@Forte
Masz podpiąć Hub usb do portu w routerze. Do hub-a podpiąć pendrive. Zrobić extroot-a, zainstalować potrzebne pakiety i na koniec podpiąć do hub-a ten modem LTE. Będziesz miał internet LTE po WiFi z routera.
Możesz spróbować zamiast pendrive użyć tej karty microSD przez zewnętrzny czytnik kart na usb.
Huba kup dobrego z dobrym zasilaczem, bo może Ci prądu braknąć na pasywnym
Ogólnie zasada jest taka: słaby router, niska cena, ale za to później są dodatkowe koszty, gdy chcesz coś więcej niż średnia krajowa .
@all_user
Szkoda, że wszyscy czytamy zbyt pobieżnie posty, bo autor napisał w swoim pierwszym poście
(...)
Jako, że modem ma fajny slocik na kartę MicroSD (...)
I już wtedy powinien być ostudzony, bo mu 2 tygodnie z życia przepadły
EDIT: spojrzałem na datę posta nr 1 a rzeczywiste zmagania zaczęły sie później. Znowu czytam pobieżnie
Hehe Na razie dwa dni.
Nie da się tego (extroot+sieć z LTE) zrobić na modemie + karcie w modemie BEZ huba?
W międzyczasie wymieniłem modemowi firmware na najnowsze modowane.
Jeśli nie mogę tego zrobić bez huba, to jaki hub warto kupić aby był dobry i nie przepłacać?
Strony Poprzednia 1 2 3 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Pomocy - TP-Link MR3420v2 + modem Huawei e3373 + mało pamięci
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc