# ps | grep -i "simpl"
4833 root      1132 S    {simplefailover} /bin/sh /usr/bin/simplefailover
4843 root      1104 S    grep -i simpl

Ale nadal nie działa.
Może coś jeszcze trzeba zrobić albo inaczej?

Wed Oct 26 17:01:28 2016 daemon.notice netifd: wan2 (4860): sending -> AT
Wed Oct 26 17:01:29 2016 daemon.notice netifd: wan2 (4860): sending -> ATZ
Wed Oct 26 17:01:29 2016 daemon.notice netifd: wan2 (4860): sending -> ATQ0
Wed Oct 26 17:01:30 2016 daemon.notice netifd: wan2 (4860): sending -> ATV1
Wed Oct 26 17:01:30 2016 daemon.notice netifd: wan2 (4860): sending -> ATE1
Wed Oct 26 17:01:31 2016 daemon.notice netifd: wan2 (4860): sending -> ATS0=0
Wed Oct 26 17:01:32 2016 daemon.notice netifd: wan2 (4860): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 17:01:32 2016 daemon.notice netifd: wan2 (4860): Error running AT-command
Wed Oct 26 17:01:32 2016 daemon.notice netifd: wan2 (4860): Failed to initialize modem
Wed Oct 26 17:01:32 2016 daemon.notice netifd: wan2 (4891): Stopping network
Wed Oct 26 17:01:35 2016 daemon.notice netifd: wan2 (4891): sending -> AT^NDISDUP=1,0
Wed Oct 26 17:01:35 2016 daemon.notice netifd: wan2 (4891): Command failed: Permission denied
Wed Oct 26 17:01:35 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:01:35 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 17:01:37 2016 daemon.notice netifd: wan2 (4903): sending -> AT
Wed Oct 26 17:01:38 2016 daemon.notice netifd: wan2 (4903): sending -> ATZ
Wed Oct 26 17:01:38 2016 daemon.notice netifd: wan2 (4903): sending -> ATQ0
Wed Oct 26 17:01:39 2016 daemon.notice netifd: wan2 (4903): sending -> ATV1
Wed Oct 26 17:01:39 2016 daemon.notice netifd: wan2 (4903): sending -> ATE1
Wed Oct 26 17:01:40 2016 daemon.notice netifd: wan2 (4903): sending -> ATS0=0
Wed Oct 26 17:01:41 2016 daemon.notice netifd: wan2 (4903): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 17:01:41 2016 daemon.notice netifd: wan2 (4903): Error running AT-command
Wed Oct 26 17:01:41 2016 daemon.notice netifd: wan2 (4903): Failed to initialize modem
Wed Oct 26 17:01:41 2016 daemon.notice netifd: wan2 (4926): Stopping network
Wed Oct 26 17:01:44 2016 daemon.notice netifd: wan2 (4926): sending -> AT^NDISDUP=1,0
Wed Oct 26 17:01:44 2016 daemon.notice netifd: wan2 (4926): Command failed: Permission denied
Wed Oct 26 17:01:44 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:01:44 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 17:01:46 2016 daemon.notice netifd: wan2 (4938): sending -> AT
Wed Oct 26 17:01:47 2016 daemon.notice netifd: wan2 (4938): sending -> ATZ
Wed Oct 26 17:01:47 2016 daemon.notice netifd: wan2 (4938): sending -> ATQ0
Wed Oct 26 17:01:48 2016 daemon.notice netifd: wan2 (4938): sending -> ATV1
Wed Oct 26 17:01:49 2016 daemon.notice netifd: wan2 (4938): sending -> ATE1
Wed Oct 26 17:01:49 2016 daemon.notice netifd: wan2 (4938): sending -> ATS0=0
Wed Oct 26 17:01:50 2016 daemon.notice netifd: wan2 (4938): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 17:01:50 2016 daemon.notice netifd: wan2 (4938): Error running AT-command
Wed Oct 26 17:01:51 2016 daemon.notice netifd: wan2 (4938): Failed to initialize modem
Wed Oct 26 17:01:51 2016 daemon.notice netifd: wan2 (4962): Stopping network
Wed Oct 26 17:01:53 2016 daemon.notice netifd: wan2 (4962): sending -> AT^NDISDUP=1,0
Wed Oct 26 17:01:53 2016 daemon.notice netifd: wan2 (4962): Command failed: Permission denied
Wed Oct 26 17:01:53 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:01:53 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 17:01:55 2016 daemon.notice netifd: wan2 (4973): sending -> AT
Wed Oct 26 17:01:56 2016 daemon.notice netifd: wan2 (4973): sending -> ATZ
Wed Oct 26 17:01:56 2016 daemon.notice netifd: wan2 (4973): sending -> ATQ0
Wed Oct 26 17:01:57 2016 daemon.notice netifd: wan2 (4973): sending -> ATV1
Wed Oct 26 17:01:58 2016 daemon.notice netifd: wan2 (4973): sending -> ATE1
Wed Oct 26 17:01:58 2016 daemon.notice netifd: wan2 (4973): sending -> ATS0=0
Wed Oct 26 17:01:59 2016 daemon.notice netifd: wan2 (4973): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 17:02:00 2016 daemon.notice netifd: wan2 (4973): Error running AT-command
Wed Oct 26 17:02:00 2016 daemon.notice netifd: wan2 (4973): Failed to initialize modem
Wed Oct 26 17:02:00 2016 daemon.notice netifd: wan2 (4997): Stopping network
Wed Oct 26 17:02:02 2016 daemon.notice netifd: wan2 (4997): sending -> AT^NDISDUP=1,0
Wed Oct 26 17:02:02 2016 daemon.notice netifd: wan2 (4997): Command failed: Permission denied
Wed Oct 26 17:02:02 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:02:02 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 17:02:04 2016 daemon.notice netifd: wan2 (5008): sending -> AT
Wed Oct 26 17:02:05 2016 daemon.notice netifd: wan2 (5008): sending -> ATZ
Wed Oct 26 17:02:05 2016 daemon.notice netifd: wan2 (5008): sending -> ATQ0
Wed Oct 26 17:02:06 2016 daemon.notice netifd: wan2 (5008): sending -> ATV1
Wed Oct 26 17:02:07 2016 daemon.notice netifd: wan2 (5008): sending -> ATE1
Wed Oct 26 17:02:07 2016 daemon.notice netifd: wan2 (5008): sending -> ATS0=0
Wed Oct 26 17:02:08 2016 daemon.notice netifd: wan2 (5008): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 17:02:09 2016 daemon.notice netifd: wan2 (5008): Error running AT-command
Wed Oct 26 17:02:09 2016 daemon.notice netifd: wan2 (5008): Failed to initialize modem
Wed Oct 26 17:02:09 2016 daemon.notice netifd: wan2 (5032): Stopping network
Wed Oct 26 17:02:11 2016 daemon.notice netifd: wan2 (5032): sending -> AT^NDISDUP=1,0
Wed Oct 26 17:02:11 2016 daemon.notice netifd: wan2 (5032): Command failed: Permission denied
Wed Oct 26 17:02:11 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:02:11 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 17:02:13 2016 daemon.notice netifd: wan2 (5046): sending -> AT
Wed Oct 26 17:02:14 2016 daemon.notice netifd: wan2 (5046): sending -> ATZ
Wed Oct 26 17:02:15 2016 daemon.notice netifd: wan2 (5046): sending -> ATQ0
Wed Oct 26 17:02:15 2016 daemon.notice netifd: wan2 (5046): sending -> ATV1
Wed Oct 26 17:02:16 2016 daemon.info dnsmasq-dhcp[3710]: DHCPINFORM(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a
Wed Oct 26 17:02:16 2016 daemon.info dnsmasq-dhcp[3710]: DHCPACK(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a datpol
Wed Oct 26 17:02:16 2016 daemon.notice netifd: wan2 (5046): sending -> ATE1
Wed Oct 26 17:02:16 2016 daemon.notice netifd: wan2 (5046): sending -> ATS0=0
Wed Oct 26 17:02:17 2016 daemon.notice netifd: wan2 (5046): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 17:02:18 2016 daemon.notice netifd: wan2 (5046): Error running AT-command
Wed Oct 26 17:02:18 2016 daemon.notice netifd: wan2 (5046): Failed to initialize modem
Wed Oct 26 17:02:18 2016 daemon.notice netifd: wan2 (5067): Stopping network
Wed Oct 26 17:02:18 2016 kern.debug kernel: [  185.951992] ieee80211 phy0: Added a new stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 17:02:18 2016 kern.debug kernel: [  185.958602] ieee80211 phy0: Started stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 17:02:18 2016 kern.notice kernel: [  185.965659] ieee80211 phy0: tx rings drained
Wed Oct 26 17:02:18 2016 kern.debug kernel: [  185.974285] ieee80211 phy0: Created a BA stream for 00:26:c6:0e:f0:3a : tid 0
Wed Oct 26 17:02:20 2016 daemon.notice netifd: wan2 (5067): sending -> AT^NDISDUP=1,0
Wed Oct 26 17:02:20 2016 daemon.notice netifd: wan2 (5067): Command failed: Permission denied
Wed Oct 26 17:02:20 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:02:20 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 17:02:21 2016 user.notice /usr/bin/simplefailover: Changing connection to main wan: wan
Wed Oct 26 17:02:21 2016 daemon.notice netifd: wan2 (5093): Stopping network
Wed Oct 26 17:02:23 2016 daemon.notice netifd: wan2 (5093): sending ->
Wed Oct 26 17:02:26 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 17:03:38 2016 daemon.info dnsmasq-dhcp[3710]: DHCPINFORM(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a
Wed Oct 26 17:03:38 2016 daemon.info dnsmasq-dhcp[3710]: DHCPACK(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a datpol
Wed Oct 26 17:04:39 2016 daemon.info dnsmasq-dhcp[3710]: DHCPINFORM(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a
Wed Oct 26 17:04:39 2016 daemon.info dnsmasq-dhcp[3710]: DHCPACK(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a datpol

Wed Oct 26 21:21:10 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 21:21:10 2016 user.notice /usr/bin/simplefailover: Changing connection to backup wan: wan2
Wed Oct 26 21:21:11 2016 kern.debug kernel: [   84.786168] ieee80211 phy0: Deleted BA stream index 0
Wed Oct 26 21:21:11 2016 kern.debug kernel: [   84.791278] ieee80211 phy0: Remove stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 21:21:13 2016 daemon.notice netifd: wan2 (4861): sending -> AT
Wed Oct 26 21:21:13 2016 daemon.notice netifd: wan2 (4861): sending -> ATZ
Wed Oct 26 21:21:14 2016 daemon.notice netifd: wan2 (4861): sending -> ATQ0
Wed Oct 26 21:21:14 2016 daemon.notice netifd: wan2 (4861): sending -> ATV1
Wed Oct 26 21:21:15 2016 daemon.notice netifd: wan2 (4861): sending -> ATE1
Wed Oct 26 21:21:16 2016 daemon.notice netifd: wan2 (4861): sending -> ATS0=0
Wed Oct 26 21:21:16 2016 daemon.notice netifd: wan2 (4861): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 21:21:17 2016 daemon.notice netifd: wan2 (4861): Error running AT-command
Wed Oct 26 21:21:17 2016 daemon.notice netifd: wan2 (4861): Failed to initialize modem
Wed Oct 26 21:21:17 2016 daemon.notice netifd: wan2 (4892): Stopping network
Wed Oct 26 21:21:19 2016 daemon.notice netifd: wan2 (4892): sending -> AT^NDISDUP=1,0
Wed Oct 26 21:21:19 2016 daemon.notice netifd: wan2 (4892): Command failed: Permission denied
Wed Oct 26 21:21:19 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 21:21:19 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 21:21:22 2016 daemon.notice netifd: wan2 (4904): sending -> AT
Wed Oct 26 21:21:22 2016 daemon.notice netifd: wan2 (4904): sending -> ATZ
Wed Oct 26 21:21:23 2016 daemon.notice netifd: wan2 (4904): sending -> ATQ0
Wed Oct 26 21:21:23 2016 daemon.notice netifd: wan2 (4904): sending -> ATV1
Wed Oct 26 21:21:24 2016 daemon.notice netifd: wan2 (4904): sending -> ATE1
Wed Oct 26 21:21:25 2016 daemon.notice netifd: wan2 (4904): sending -> ATS0=0
Wed Oct 26 21:21:25 2016 daemon.notice netifd: wan2 (4904): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 21:21:26 2016 daemon.notice netifd: wan2 (4904): Error running AT-command
Wed Oct 26 21:21:26 2016 daemon.notice netifd: wan2 (4904): Failed to initialize modem
Wed Oct 26 21:21:26 2016 daemon.notice netifd: wan2 (4927): Stopping network
Wed Oct 26 21:21:28 2016 daemon.notice netifd: wan2 (4927): sending -> AT^NDISDUP=1,0
Wed Oct 26 21:21:29 2016 daemon.notice netifd: wan2 (4927): Command failed: Permission denied
Wed Oct 26 21:21:29 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 21:21:29 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 21:21:31 2016 daemon.notice netifd: wan2 (4939): sending -> AT
Wed Oct 26 21:21:31 2016 daemon.notice netifd: wan2 (4939): sending -> ATZ
Wed Oct 26 21:21:32 2016 daemon.notice netifd: wan2 (4939): sending -> ATQ0
Wed Oct 26 21:21:33 2016 daemon.notice netifd: wan2 (4939): sending -> ATV1
Wed Oct 26 21:21:33 2016 daemon.notice netifd: wan2 (4939): sending -> ATE1
Wed Oct 26 21:21:34 2016 daemon.notice netifd: wan2 (4939): sending -> ATS0=0
Wed Oct 26 21:21:34 2016 daemon.notice netifd: wan2 (4939): sending -> AT+CGDCONT=1,"IPV4V6","internet"
Wed Oct 26 21:21:35 2016 daemon.notice netifd: wan2 (4939): Error running AT-command
Wed Oct 26 21:21:35 2016 daemon.notice netifd: wan2 (4939): Failed to initialize modem
Wed Oct 26 21:21:35 2016 daemon.notice netifd: wan2 (4963): Stopping network
Wed Oct 26 21:21:37 2016 daemon.notice netifd: wan2 (4963): sending -> AT^NDISDUP=1,0
Wed Oct 26 21:21:38 2016 daemon.notice netifd: wan2 (4963): Command failed: Permission denied
Wed Oct 26 21:21:38 2016 daemon.notice netifd: Interface 'wan2' is now down
Wed Oct 26 21:21:38 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 21:21:38 2016 daemon.info dnsmasq-dhcp[3716]: DHCPINFORM(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a
Wed Oct 26 21:21:38 2016 daemon.info dnsmasq-dhcp[3716]: DHCPACK(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a datpol
Wed Oct 26 21:21:39 2016 kern.debug kernel: [  112.541687] ieee80211 phy0: Added a new stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 21:21:39 2016 kern.debug kernel: [  112.548270] ieee80211 phy0: Started stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 21:21:39 2016 kern.debug kernel: [  112.559020] ieee80211 phy0: Created a BA stream for 00:26:c6:0e:f0:3a : tid 0

Dlaczego? Na usb 0 i 1 to samo.

Gdzie?

Wed Oct 26 22:29:19 2016 daemon.notice netifd: Interface 'wan2' is setting up now
Wed Oct 26 22:29:19 2016 user.notice /usr/bin/simplefailover: Changing connection to backup wan: wan2
Wed Oct 26 22:29:21 2016 daemon.notice netifd: wan2 (4908): sending -> AT
Wed Oct 26 22:29:22 2016 daemon.notice netifd: wan2 (4908): sending -> ATZ
Wed Oct 26 22:29:22 2016 daemon.notice netifd: wan2 (4908): sending -> ATQ0
Wed Oct 26 22:29:23 2016 daemon.notice netifd: wan2 (4908): sending -> ATV1
Wed Oct 26 22:29:23 2016 daemon.notice netifd: wan2 (4908): sending -> ATE1
Wed Oct 26 22:29:24 2016 daemon.notice netifd: wan2 (4908): sending -> ATS0=0
Wed Oct 26 22:29:25 2016 daemon.notice netifd: wan2 (4908): sending -> AT+CGDCONT=1,"IP","internet"
Wed Oct 26 22:29:26 2016 daemon.notice netifd: wan2 (4908): sending -> AT^NDISDUP=1,1,"internet"
Wed Oct 26 22:29:26 2016 daemon.notice netifd: wan2 (4908): Connected, starting DHCP on wwan0
Wed Oct 26 22:29:26 2016 daemon.notice netifd: Interface 'wan2' is now up
Wed Oct 26 22:29:26 2016 daemon.notice netifd: Network device 'wwan0' link is up
Wed Oct 26 22:29:26 2016 daemon.notice netifd: Network alias 'wwan0' link is up
Wed Oct 26 22:29:26 2016 daemon.notice netifd: Interface 'wan2_4' is enabled
Wed Oct 26 22:29:26 2016 daemon.notice netifd: Interface 'wan2_4' has link connectivity
Wed Oct 26 22:29:26 2016 daemon.notice netifd: Interface 'wan2_4' is setting up now
Wed Oct 26 22:29:26 2016 daemon.notice netifd: wan2 (4908): Command failed: Unknown error
Wed Oct 26 22:29:27 2016 daemon.notice netifd: wan2_4 (4960): udhcpc: started, v1.25.1
Wed Oct 26 22:29:27 2016 user.notice firewall: Reloading firewall due to ifup of wan2 (wwan0)
Wed Oct 26 22:29:27 2016 daemon.notice netifd: wan2_4 (4960): udhcpc: sending discover
Wed Oct 26 22:29:30 2016 daemon.notice netifd: wan2_4 (4960): udhcpc: sending discover
Wed Oct 26 22:29:33 2016 daemon.notice netifd: wan2_4 (4960): udhcpc: sending discover
Wed Oct 26 22:29:37 2016 kern.debug kernel: [  242.647346] ieee80211 phy0: Added a new stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 22:29:37 2016 kern.debug kernel: [  242.653950] ieee80211 phy0: Started stream for 00:26:c6:0e:f0:3a 0
Wed Oct 26 22:29:37 2016 kern.debug kernel: [  242.664688] ieee80211 phy0: Created a BA stream for 00:26:c6:0e:f0:3a : tid 0

Jak wkładam do komputera to działa poprawnie.

No nie i właśnie nie wiem jak to naprawić...
Poradzisz?

Przy 3g zadziałało.
Skrypt nie startuje po reboocie. Dodałem

# Put your custom commands here that should be executed once
# the system init finished. By default this file does nothing.
/etc/init.d/simplefailover start

exit 0

Ale nie startuje nadal - jak to naprawić?

# logread
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Booting Linux on physical CPU 0x0
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000] Linux version 4.4.27 (buildbot@builds) (gcc version 5.4.0 (LEDE GCC 5.4.0 r1967) ) #0 Mon Oct 24 20:52:44 2016
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] CPU: VIVT data cache, VIVT instruction cache
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Machine model: Linksys E4200v2 / EA4500
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Memory policy: Data cache writeback
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000] On node 0 totalpages: 32768
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat c057773c, node_mem_map c7efa000
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000]   Normal zone: 256 pages used for memmap
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000]   Normal zone: 32768 pages, LIFO batch:7
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:512k(uboot)ro,128k@512k(u_env),128k@640k(s_env),26m@2m(kernel),26m@2m(rootfs)fs,26m@28m(alt_kernel),26m@28m(alt_rootfs)fs,74m@54m(syscfg) root=/dev/mtdblock4 ro rootfstype=jffs2 serial_number=12A10603207378 uuid=8B71F27566F70121ABDB7375720D9821 hw_version=RGWM-C4_0GA device_mac=20:AA:4B:7A:EB:A9 factory_date=2012/03/05 wps_pin=69160813
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] Memory: 123932K/131072K available (3922K kernel code, 135K rwdata, 1444K rodata, 168K init, 197K bss, 7140K reserved, 0K cma-reserved)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000] Virtual kernel memory layout:
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]       .text : 0xc0008000 - 0xc0545db4   (5368 kB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]       .init : 0xc0546000 - 0xc0570000   ( 168 kB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]       .data : 0xc0570000 - 0xc0591dc0   ( 136 kB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.000000]        .bss : 0xc0591dc0 - 0xc05c33b4   ( 198 kB)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] NR_IRQS:16 nr_irqs:16 16
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.000078] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.090076] pid_max: default: 32768 minimum: 301
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.090180] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.090198] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.090722] CPU: Testing write buffer coherency: ok
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.091057] Setting up static identity map for 0x81e0 - 0x821c
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.091330] mvebu-soc-id: MVEBU SoC ID=0x6282, Rev=0x1
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.096295] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.096437] pinctrl core: initialized pinctrl subsystem
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.097584] NET: Registered protocol family 16
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.098004] DMA: preallocated 256 KiB pool for atomic coherent allocations
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.098881] cpuidle: using governor ladder
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.099307] Feroceon L2: Enabling L2
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.099350] Feroceon L2: Cache support initialised.
Thu Oct 27 18:53:29 2016 kern.err kernel: [    0.099606] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
Thu Oct 27 18:53:29 2016 kern.err kernel: [    0.099703] [Firmware Info]: /ocp@f1000000/ethernet-controller@76000/ethernet1-port@0: local-mac-address is not set
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.115736] SCSI subsystem initialized
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.116057] usbcore: registered new interface driver usbfs
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.116144] usbcore: registered new interface driver hub
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.116206] usbcore: registered new device driver usb
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.117223] clocksource: Switched to clocksource orion_clocksource
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.118162] NET: Registered protocol family 2
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.118749] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.118773] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.118792] TCP: Hash tables configured (established 1024 bind 1024)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.118847] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.118869] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.119030] NET: Registered protocol family 1
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.119084] PCI: CLS 0 bytes, default 32
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.119931] futex hash table entries: 256 (order: -1, 3072 bytes)
Thu Oct 27 18:53:29 2016 kern.warn kernel: [    0.120007] Crashlog allocated RAM at address 0x3f00000
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.134569] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.134589] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.137070] io scheduler noop registered
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.137089] io scheduler deadline registered (default)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.138310] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.138893] irq: Cannot allocate irq_descs @ IRQ31, assuming pre-allocated
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.139236] irq: Cannot allocate irq_descs @ IRQ63, assuming pre-allocated
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.139857] mvebu-pcie mbus:pcie-controller: PCI host bridge to bus 0000:00
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.139876] pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.139888] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.139900] pci_bus 0000:00: root bus resource [bus 00-ff]
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.139932] pci 0000:00:01.0: [11ab:6282] type 01 class 0x060400
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.140171] pci 0000:00:02.0: [11ab:6282] type 01 class 0x060400
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.140402] PCI: bus0: Fast back to back transfers disabled
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.140416] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.140431] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.140574] pci 0000:01:00.0: [11ab:2a41] type 00 class 0x020000
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.140631] pci 0000:01:00.0: reg 0x10: [mem 0x90000000-0x9000ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.140657] pci 0000:01:00.0: reg 0x18: [mem 0x90010000-0x9001ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.140919] PCI: bus1: Fast back to back transfers disabled
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.140935] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.141079] pci 0000:02:00.0: [11ab:2a42] type 00 class 0x020000
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.141132] pci 0000:02:00.0: reg 0x10: [mem 0x98000000-0x9800ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.141158] pci 0000:02:00.0: reg 0x18: [mem 0x98010000-0x9801ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141425] PCI: bus2: Fast back to back transfers disabled
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    0.141440] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141547] pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe00fffff]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141563] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0100000-0xe01fffff]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141580] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141604] pci 0000:01:00.0: BAR 2: assigned [mem 0xe0010000-0xe001ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141624] pci 0000:00:01.0: PCI bridge to [bus 01]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141638] pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe00fffff]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141656] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0100000-0xe010ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141678] pci 0000:02:00.0: BAR 2: assigned [mem 0xe0110000-0xe011ffff 64bit]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141698] pci 0000:00:02.0: PCI bridge to [bus 02]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.141711] pci 0000:00:02.0:   bridge window [mem 0xe0100000-0xe01fffff]
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.172585] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.175440] console [ttyS0] disabled
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.175516] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.782068] console [ttyS0] enabled
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.786881] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.793294] nand: Hynix H27U1G8F2BTR-BC
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.797144] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.804769] Scanning device for bad blocks
Thu Oct 27 18:53:29 2016 kern.warn kernel: [    0.858529] Bad eraseblock 767 at 0x000005fe0000
Thu Oct 27 18:53:29 2016 kern.err kernel: [    0.879738] mtd: bad character after partition (f)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.884577] 8 ofpart partitions found on MTD device orion_nand
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.890446] Creating 8 MTD partitions on "orion_nand":
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.895615] 0x000000000000-0x000000080000 : "u-boot"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.902165] 0x000000080000-0x0000000a0000 : "u_env"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.908210] 0x0000000a0000-0x0000000c0000 : "s_env"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.914163] 0x000000200000-0x000001c00000 : "kernel1"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.920392] 0x0000004a0000-0x000001c00000 : "ubi"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.926233] 0x000001c00000-0x000003600000 : "kernel2"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.932472] 0x000001ea0000-0x000003600000 : "rootfs2"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.938708] 0x000003600000-0x000008000000 : "syscfg"
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.945430] libphy: orion_mdio_bus: probed
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.949736] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.957841] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 20:aa:4b:7a:eb:a9
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    0.967144] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 20:aa:4b:7a:eb:aa
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.975973] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.982555] ehci-pci: EHCI PCI platform driver
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.987097] ehci-platform: EHCI generic platform driver
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.992510] ehci-orion: EHCI orion driver
Thu Oct 27 18:53:29 2016 kern.info kernel: [    0.996682] orion-ehci f1050000.ehci: EHCI Host Controller
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.002242] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.010066] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.027252] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.033969] hub 1-0:1.0: USB hub found
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.037950] hub 1-0:1.0: 1 port detected
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.042338] usbcore: registered new interface driver usb-storage
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.050216] NET: Registered protocol family 10
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.057362] NET: Registered protocol family 17
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.061886] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.074574] 8021q: 802.1Q VLAN Support v1.8
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.080866] UBI: auto-attach mtd4
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.084029] ubi0: attaching mtd4
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.111678] ubi0: scanning is finished
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.121957] ubi0: attached mtd4 (name "ubi", size 23 MiB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.127406] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.134310] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.141062] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.147892] ubi0: good PEBs: 187, bad PEBs: 0, corrupted PEBs: 0
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.153921] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.161191] ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 1515048255
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.170372] ubi0: available PEBs: 0, total reserved PEBs: 187, PEBs reserved for bad PEB handling: 20
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.180000] ubi0: background thread "ubi_bgt0d" started, PID 880
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.186711] block ubiblock0_0: created from ubi0:0(rootfs)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    1.192249] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.199919] mvsw61xx 10.mvsw61xx: Found MV88E6171 at f1072004.mdio-bu:10
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.206654] mvsw61xx 10.mvsw61xx: Using indirect addressing
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.243174] hctosys: unable to open rtc device (rtc0)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.253407] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.261107] Freeing unused kernel memory: 168K (c0546000 - c0570000)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.440608] usb 1-1: new high-speed USB device number 2 using orion-ehci
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.737958] usb-storage 1-1:1.3: USB Mass Storage device detected
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.757516] scsi host0: usb-storage 1-1:1.3
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.762404] usb-storage 1-1:1.4: USB Mass Storage device detected
Thu Oct 27 18:53:29 2016 kern.info kernel: [    1.777453] scsi host1: usb-storage 1-1:1.4
Thu Oct 27 18:53:29 2016 user.info kernel: [    1.789948] init: Console is alive
Thu Oct 27 18:53:29 2016 kern.debug kernel: [    2.183256] libata version 3.00 loaded.
Thu Oct 27 18:53:29 2016 user.info kernel: [    2.187938] init: - preinit -
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.500678] random: jshn: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.568373] random: jshn: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.677464] random: jshn: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.711176] random: jshn: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.764578] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.773579] random: procd: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.786302] random: jshn: uninitialized urandom read (4 bytes read, 10 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.796423] scsi 1:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    2.818017] sd 1:0:0:0: [sda] Attached SCSI removable disk
Thu Oct 27 18:53:29 2016 kern.info kernel: [    3.091928] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.284423] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 990
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.305874] UBIFS (ubi0:1): recovery needed
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.435397] UBIFS (ubi0:1): recovery completed
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.439967] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.447853] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.457825] UBIFS (ubi0:1): FS size: 17676288 bytes (16 MiB, 137 LEBs), journal size 1032193 bytes (0 MiB, 7 LEBs)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.468233] UBIFS (ubi0:1): reserved for root: 834894 bytes (815 KiB)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    5.474705] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID 6562FA60-726A-4D53-A208-418251C651CD, small LPT model
Thu Oct 27 18:53:29 2016 user.info kernel: [    5.489706] mount_root: switching to ubifs overlay
Thu Oct 27 18:53:29 2016 user.warn kernel: [    5.498930] urandom-seed: Seeding with /etc/urandom.seed
Thu Oct 27 18:53:29 2016 user.info kernel: [    5.569200] procd: - early -
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    6.051664] random: jshn: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    6.126517] random: jshn: uninitialized urandom read (4 bytes read, 27 bits of entropy available)
Thu Oct 27 18:53:29 2016 user.info kernel: [    6.532691] procd: - ubus -
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    6.611516] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
Thu Oct 27 18:53:29 2016 kern.notice kernel: [    6.752278] random: ubusd: uninitialized urandom read (4 bytes read, 28 bits of entropy available)
Thu Oct 27 18:53:29 2016 user.info kernel: [    6.942844] procd: - init -
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.233480] ip6_tables: (C) 2000-2006 Netfilter Core Team
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.258911] i2c /dev entries driver
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.279951] usbcore: registered new interface driver cdc_wdm
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.287372] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.294980] Backport generated by backports.git backports-20160324-9-g0e38f5c
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.330688] ip_tables: (C) 2000-2006 Netfilter Core Team
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.349865] nf_conntrack version 0.5.0 (1939 buckets, 7756 max)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.403586] usbcore: registered new interface driver usbserial
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.409574] usbcore: registered new interface driver usbserial_generic
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.416198] usbserial: USB Serial support registered for generic
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.461829] xt_time: kernel timezone is -0000
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.485524] usbcore: registered new interface driver cdc_ncm
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.538982] huawei_cdc_ncm 1-1:1.2: MAC-Address: 0c:5b:8f:27:9a:64
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.545212] huawei_cdc_ncm 1-1:1.2: setting rx_max = 16384
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.563285] huawei_cdc_ncm 1-1:1.2: setting tx_max = 16384
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.571705] huawei_cdc_ncm 1-1:1.2: NDP will be placed at end of frame for this device.
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.579988] huawei_cdc_ncm 1-1:1.2: cdc-wdm0: USB WDM device
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.586509] huawei_cdc_ncm 1-1:1.2 wwan0: register 'huawei_cdc_ncm' at usb-f1050000.ehci-1, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.598618] usbcore: registered new interface driver huawei_cdc_ncm
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.679096] Marvell TOPDOG(R) 802.11 Wireless Network Driver version 0.13
Thu Oct 27 18:53:29 2016 kern.info kernel: [    7.685944] pci 0000:00:01.0: enabling device (0140 -> 0142)
Thu Oct 27 18:53:29 2016 kern.err kernel: [    8.639453] ieee80211 phy0: Command RF_ANTENNA error 0x2
Thu Oct 27 18:53:29 2016 kern.warn kernel: [    8.644800] ieee80211 phy0: failed to set # of RX antennas
Thu Oct 27 18:53:29 2016 kern.err kernel: [    8.664751] ieee80211 phy0: Command RF_ANTENNA error 0x2
Thu Oct 27 18:53:29 2016 kern.warn kernel: [    8.670139] ieee80211 phy0: failed to set # of TX antennas
Thu Oct 27 18:53:29 2016 kern.info kernel: [    8.675659] ieee80211 phy0: 88w8366 v48, 20aa4b7aebab, STA firmware 4.1.0.3
Thu Oct 27 18:53:29 2016 kern.info kernel: [    8.685076] pci 0000:00:02.0: enabling device (0140 -> 0142)
Thu Oct 27 18:53:29 2016 kern.err kernel: [    9.490527] ieee80211 phy1: Command RF_ANTENNA error 0x2
Thu Oct 27 18:53:29 2016 kern.warn kernel: [    9.495872] ieee80211 phy1: failed to set # of RX antennas
Thu Oct 27 18:53:29 2016 kern.err kernel: [    9.516523] ieee80211 phy1: Command RF_ANTENNA error 0x2
Thu Oct 27 18:53:29 2016 kern.warn kernel: [    9.521915] ieee80211 phy1: failed to set # of TX antennas
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.527451] ieee80211 phy1: 88w8366 v48, 20aa4b7aebad, STA firmware 4.1.0.3
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.542452] PPP generic driver version 2.4.2
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.547663] NET: Registered protocol family 24
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.579888] usbcore: registered new interface driver option
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.585571] usbserial: USB Serial support registered for GSM modem (1-port)
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.592802] option 1-1:1.0: GSM modem (1-port) converter detected
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.599189] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.606102] option 1-1:1.1: GSM modem (1-port) converter detected
Thu Oct 27 18:53:29 2016 kern.info kernel: [    9.612460] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Thu Oct 27 18:53:30 2016 user.notice : Added device handler type: tunnel
Thu Oct 27 18:53:30 2016 user.notice : Added device handler type: Network device
Thu Oct 27 18:53:30 2016 user.notice : Added device handler type: bridge
Thu Oct 27 18:53:30 2016 user.notice : Added device handler type: macvlan
Thu Oct 27 18:53:30 2016 user.notice : Added device handler type: 8021ad
Thu Oct 27 18:53:30 2016 user.notice : Added device handler type: 8021q
Thu Oct 27 18:53:30 2016 user.notice : 'radio1' is disabled
Thu Oct 27 18:53:30 2016 user.notice : 'radio1' is disabled
Thu Oct 27 18:53:31 2016 authpriv.info dropbear[2550]: Not backgrounding
Thu Oct 27 18:53:32 2016 user.notice : setting up led health
Thu Oct 27 18:53:32 2016 user.notice : setting up led pulse
Thu Oct 27 18:53:33 2016 kern.info kernel: [   16.848650] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
Thu Oct 27 18:53:33 2016 kern.info kernel: [   16.870750] device eth0 entered promiscuous mode
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'lan' is enabled
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'lan' is setting up now
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'lan' is now up
Thu Oct 27 18:53:33 2016 kern.info kernel: [   16.888016] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'loopback' is enabled
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'loopback' is setting up now
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'loopback' is now up
Thu Oct 27 18:53:33 2016 kern.info kernel: [   16.918280] mv643xx_eth_port mv643xx_eth_port.1 eth1: link up, 1000 Mb/s, full duplex, flow control disabled
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'wan' is enabled
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'wan6' is enabled
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Network device 'eth0' link is up
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Network device 'lo' link is up
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'loopback' has link connectivity
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Network device 'eth1' link is up
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'wan' is setting up now
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'wan6' has link connectivity
Thu Oct 27 18:53:33 2016 daemon.notice netifd: Interface 'wan6' is setting up now
Thu Oct 27 18:53:34 2016 user.notice /usr/bin/simplefailover: No gateway on wan?
Thu Oct 27 18:53:34 2016 daemon.notice netifd: wan (2782): udhcpc: started, v1.25.1
Thu Oct 27 18:53:34 2016 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Thu Oct 27 18:53:34 2016 daemon.notice netifd: wan (2782): udhcpc: sending discover
Thu Oct 27 18:53:34 2016 kern.info kernel: [   17.847333] br-lan: port 1(eth0) entered forwarding state
Thu Oct 27 18:53:34 2016 kern.info kernel: [   17.852819] br-lan: port 1(eth0) entered forwarding state
Thu Oct 27 18:53:34 2016 daemon.notice netifd: bridge 'br-lan' link is up
Thu Oct 27 18:53:34 2016 daemon.notice netifd: Interface 'lan' has link connectivity
Thu Oct 27 18:53:34 2016 kern.info kernel: [   17.945294] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Thu Oct 27 18:53:35 2016 daemon.notice netifd: radio0 (2744): command failed: Not supported (-95)
Thu Oct 27 18:53:35 2016 user.notice /usr/bin/simplefailover: No gateway on wan?
Thu Oct 27 18:53:35 2016 daemon.info procd: - init complete -
Thu Oct 27 18:53:35 2016 daemon.notice vnstatd[2916]: vnStat daemon 1.12 started. (uid:0 gid:0)
Thu Oct 27 18:53:35 2016 daemon.notice vnstatd[2916]: Monitoring: br-lan (100 Mbit) eth1 (100 Mbit)
Thu Oct 27 18:53:35 2016 daemon.notice netifd: radio0 (2744): Configuration file: /var/run/hostapd-phy0.conf
Thu Oct 27 18:53:35 2016 daemon.notice netifd: wan (2782): udhcpc: sending select for 192.168.2.10
Thu Oct 27 18:53:35 2016 daemon.notice netifd: wan (2782): udhcpc: lease of 192.168.2.10 obtained, lease time 864000
Thu Oct 27 18:53:36 2016 kern.info kernel: [   19.386578] ieee80211 phy0: 88w8366 v7, 20aa4b7aebab, AP firmware 5.2.8.17
Thu Oct 27 18:53:36 2016 daemon.notice netifd: Interface 'wan' is now up
Thu Oct 27 18:53:36 2016 kern.info kernel: [   19.454515] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Thu Oct 27 18:53:36 2016 kern.info kernel: [   19.500038] device wlan0 entered promiscuous mode
Thu Oct 27 18:53:36 2016 daemon.notice netifd: radio0 (2744): wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Thu Oct 27 18:53:36 2016 daemon.notice netifd: radio0 (2744): wlan0: interface state COUNTRY_UPDATE->HT_SCAN
Thu Oct 27 18:53:36 2016 user.notice firewall: Reloading firewall due to ifup of wan (eth1)
Thu Oct 27 18:53:36 2016 kern.info kernel: [   19.847261] br-lan: port 1(eth0) entered forwarding state
Thu Oct 27 18:53:37 2016 daemon.notice netifd: radio0 (2744): 20/40 MHz operation not permitted on channel pri=3 sec=7 based on overlapping BSSes
Thu Oct 27 18:53:37 2016 daemon.notice netifd: radio0 (2744): Using interface wlan0 with hwaddr 20:aa:4b:7a:eb:ab and ssid "Szmanda.info"
Thu Oct 27 18:53:38 2016 kern.info kernel: [   21.330754] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Thu Oct 27 18:53:38 2016 kern.info kernel: [   21.337303] br-lan: port 2(wlan0) entered forwarding state
Thu Oct 27 18:53:38 2016 kern.info kernel: [   21.342855] br-lan: port 2(wlan0) entered forwarding state
Thu Oct 27 18:53:38 2016 daemon.notice netifd: radio0 (2744): wlan0: interface state HT_SCAN->ENABLED
Thu Oct 27 18:53:38 2016 daemon.notice netifd: radio0 (2744): wlan0: AP-ENABLED
Thu Oct 27 18:53:38 2016 daemon.notice netifd: Network device 'wlan0' link is up
Thu Oct 27 18:53:40 2016 daemon.info hostapd: wlan0: STA 00:26:c6:0e:f0:3a IEEE 802.11: authenticated
Thu Oct 27 18:53:40 2016 daemon.info hostapd: wlan0: STA 00:26:c6:0e:f0:3a IEEE 802.11: associated (aid 1)
Thu Oct 27 18:53:40 2016 daemon.info hostapd: wlan0: STA 00:26:c6:0e:f0:3a WPA: pairwise key handshake completed (RSN)
Thu Oct 27 18:53:40 2016 kern.info kernel: [   23.337261] br-lan: port 2(wlan0) entered forwarding state
Thu Oct 27 18:53:41 2016 daemon.warn odhcpd[2481]: DHCPV6 CONFIRM IA_NA from 000100011f281d3df4ce4697932d on br-lan: not on-link
Thu Oct 27 18:53:42 2016 daemon.warn odhcpd[2481]: DHCPV6 CONFIRM IA_NA from 000100011f281d3df4ce4697932d on br-lan: not on-link
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: started, version 2.76 cachesize 150
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: DNS service limited to local subnets
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq-dhcp[3727]: DHCP, IP range 10.0.0.100 -- 10.0.0.249, lease time 12h
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: using local addresses only for domain lan
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: reading /tmp/resolv.conf.auto
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: using local addresses only for domain lan
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: using nameserver 192.168.2.1#53
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: read /etc/hosts - 4 addresses
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: read /tmp/hosts/dhcp - 2 addresses
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq[3727]: read /tmp/hosts/odhcpd - 0 addresses
Thu Oct 27 18:53:42 2016 daemon.info dnsmasq-dhcp[3727]: read /etc/ethers - 0 addresses
Thu Oct 27 18:53:43 2016 kern.debug kernel: [   26.713248] ieee80211 phy0: Added a new stream for 00:26:c6:0e:f0:3a 0
Thu Oct 27 18:53:43 2016 kern.debug kernel: [   26.719875] ieee80211 phy0: Started stream for 00:26:c6:0e:f0:3a 0
Thu Oct 27 18:53:43 2016 kern.notice kernel: [   26.737641] ieee80211 phy0: tx rings drained
Thu Oct 27 18:53:43 2016 kern.debug kernel: [   26.747272] ieee80211 phy0: Created a BA stream for 00:26:c6:0e:f0:3a : tid 0
Thu Oct 27 18:53:43 2016 daemon.info dnsmasq-dhcp[3727]: DHCPREQUEST(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a
Thu Oct 27 18:53:43 2016 daemon.info dnsmasq-dhcp[3727]: DHCPACK(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a datpol
Thu Oct 27 18:53:43 2016 daemon.warn dnsmasq-dhcp[3727]: not giving name datpol.lan to the DHCP lease of 10.0.0.106 because the name exists in /tmp/hosts/dhcp with address 10.10.0.1
Thu Oct 27 18:53:43 2016 daemon.warn dnsmasq-dhcp[3727]: not giving name datpol to the DHCP lease of 10.0.0.106 because the name exists in /tmp/hosts/dhcp with address 10.10.0.1
Thu Oct 27 18:53:44 2016 daemon.warn odhcpd[2481]: DHCPV6 CONFIRM IA_NA from 000100011f281d3df4ce4697932d on br-lan: not on-link
Thu Oct 27 19:44:45 2016 daemon.info dnsmasq[3727]: read /etc/hosts - 4 addresses
Thu Oct 27 19:44:45 2016 daemon.info dnsmasq[3727]: read /tmp/hosts/dhcp - 2 addresses
Thu Oct 27 19:44:45 2016 daemon.info dnsmasq[3727]: read /tmp/hosts/odhcpd - 0 addresses
Thu Oct 27 19:44:45 2016 daemon.info dnsmasq-dhcp[3727]: read /etc/ethers - 0 addresses
Thu Oct 27 19:44:45 2016 daemon.warn dnsmasq-dhcp[3727]: not giving name datpol.lan to the DHCP lease of 10.0.0.106 because the name exists in /tmp/hosts/dhcp with address 10.10.0.1
Thu Oct 27 19:44:45 2016 daemon.warn dnsmasq-dhcp[3727]: not giving name datpol to the DHCP lease of 10.0.0.106 because the name exists in /tmp/hosts/dhcp with address 10.10.0.1
Thu Oct 27 19:44:45 2016 daemon.info dnsmasq-dhcp[3727]: DHCPINFORM(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a
Thu Oct 27 19:44:45 2016 daemon.info dnsmasq-dhcp[3727]: DHCPACK(br-lan) 10.0.0.106 00:26:c6:0e:f0:3a datpol
Thu Oct 27 19:44:45 2016 daemon.warn odhcpd[2481]: DHCPV6 SOLICIT IA_NA from 000100011f281d3df4ce4697932d on br-lan: ok fda1:9885:2cdd::614/128
Thu Oct 27 19:44:45 2016 authpriv.info dropbear[4478]: Child connection from 10.0.0.106:63842
Thu Oct 27 19:44:45 2016 kern.notice kernel: [   31.576533] random: nonblocking pool is initialized
Thu Oct 27 19:44:46 2016 daemon.warn odhcpd[2481]: DHCPV6 SOLICIT IA_NA from 000100011f281d3df4ce4697932d on br-lan: ok fda1:9885:2cdd::614/128
Thu Oct 27 19:44:48 2016 daemon.warn odhcpd[2481]: DHCPV6 SOLICIT IA_NA from 000100011f281d3df4ce4697932d on br-lan: ok fda1:9885:2cdd::614/128
Thu Oct 27 19:44:49 2016 authpriv.notice dropbear[4478]: Pubkey auth succeeded for 'root' with key md5 70:1e:39:7a:f3:9f:d8:c7:3d:a0:fc:f6:84:ab:f5:af from 10.0.0.106:63842

Podał byś całą komendę?

/etc/init.d/simplefailover disable? Albo uruchomiłeś go z palca.

Thu Oct 27 21:02:18 2016 daemon.notice netifd: Interface 'wan' is enabled
Thu Oct 27 21:02:18 2016 daemon.notice netifd: Interface 'wan6' is enabled
Thu Oct 27 21:02:18 2016 daemon.notice netifd: Interface 'wan' has link connectivity
Thu Oct 27 21:02:18 2016 daemon.notice netifd: Interface 'wan' is setting up now
Thu Oct 27 21:02:18 2016 daemon.notice netifd: Interface 'wan6' has link connectivity
Thu Oct 27 21:02:18 2016 daemon.notice netifd: Interface 'wan6' is setting up now
Thu Oct 27 21:02:19 2016 daemon.notice netifd: wan (2770): udhcpc: started, v1.25.1
Thu Oct 27 21:02:19 2016 daemon.notice netifd: wan (2770): udhcpc: sending discover
Thu Oct 27 21:02:20 2016 user.notice /usr/bin/simplefailover: No gateway on wan?
Thu Oct 27 21:02:22 2016 daemon.notice netifd: wan (2770): udhcpc: sending discover
Thu Oct 27 21:02:25 2016 daemon.notice netifd: wan (2770): udhcpc: sending discover
Thu Oct 27 21:04:17 2016 user.notice /usr/bin/simplefailover: No gateway on wan?

ps | grep -i "sim"
4908 root      1100 S    grep -i sim
root@datpol:~# /etc/init.d/simplefailover start
root@datpol:~# ps | grep -i "sim"
4910 root      1132 S    {simplefailover} /bin/sh /usr/bin/simplefailover
4920 root      1100 S    grep -i sim

OK czyli jeśli nie ma połączenie na WAN to simplefailover nie wystartuje w ogóle. Dlaczego?