Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → DIR-825 Gargoyle 1.6.2.2 konfiguracja E3372 Hilink?
Strony 1
Zaloguj się lub zarejestruj by napisać odpowiedź
Zainstalowałem ww soft, doinstalowałem
kmod-usb-net-cdc-ether , ale modem nie chce współpracować (ustawiałem już jako interfejs eth0,1,2, eth0;0.1,0.2 , niestety modem nie chce ruszyć?
W logach zobacz jaki numer interfejsu został mu przydzielony.
Ponad to nic nie trzeba doinstalowywać, moje gargoyle obsługuje hilinki i ten pakiet jest standardowo.
Pakiet się normalnie zainstalował-to chyba go nie było? (choć w zakładce konfiguracji jest od początku dodatkowa zakładka WAN-Domyślny), logi wyglądają tak
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.710000] pci 0000:00:11.0: [168c:ff1d] type 0 class 0x000200
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.710000] pci 0000:00:11.0: fixup device configuration
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.710000] pci 0000:00:11.0: reg 10: [mem 0x00000000-0x0000ffff]
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.710000] pci 0000:00:11.0: PME# supported from D0 D3hot
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.710000] pci 0000:00:12.0: [168c:ff1d] type 0 class 0x000200
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.710000] pci 0000:00:12.0: fixup device configuration
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.720000] pci 0000:00:12.0: reg 10: [mem 0x00000000-0x0000ffff]
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.720000] pci 0000:00:12.0: PME# supported from D0 D3hot
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.720000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.720000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.730000] pci 0000:00:11.0: using irq 40 for pin 1
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.730000] pci 0000:00:12.0: using irq 41 for pin 1
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.740000] Switching to clocksource MIPS
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.740000] NET: Registered protocol family 2
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.750000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.750000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.760000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.760000] TCP: Hash tables configured (established 2048 bind 2048)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.770000] TCP reno registered
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.770000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.780000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.780000] NET: Registered protocol family 1
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 2.790000] PCI: CLS 0 bytes, default 32
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.800000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.810000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.820000] msgmni has been set to 119
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.820000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.830000] io scheduler noop registered
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.830000] io scheduler deadline registered (default)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.840000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.870000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.870000] console [ttyS0] enabled, bootconsole disabled
Jan 1 01:00:13 Gargoyle kern.warn kernel: [ 2.890000] m25p80 spi0.0: found s25sl064a, expected m25p80
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.890000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.900000] 8 cmdlinepart partitions found on MTD device spi0.0
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.900000] Creating 8 MTD partitions on "spi0.0":
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.910000] 0x000000000000-0x000000040000 : "uboot"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.910000] 0x000000040000-0x000000050000 : "config"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.920000] 0x000000050000-0x000000150000 : "kernel"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.930000] 0x000000150000-0x000000660000 : "rootfs"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.930000] mtd: partition "rootfs" set to be root filesystem
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.940000] mtd: partition "rootfs_data" created automatically, ofs=3B0000, len=2B0000
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.950000] 0x0000003b0000-0x000000660000 : "rootfs_data"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.950000] 0x000000660000-0x000000670000 : "caldata"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.960000] 0x000000670000-0x000000800000 : "unknown"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.960000] 0x000000050000-0x000000660000 : "firmware"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.970000] 0x0000007f0000-0x000000800000 : "caldata_copy"
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 2.980000] Realtek RTL8366S ethernet switch driver version 0.2.2
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.990000] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 2.990000] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.020000] rtl8366s rtl8366s: applying initvals
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.030000] rtl8366s: probed
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.050000] ag71xx_mdio: probed
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.050000] eth0: Atheros AG71xx at 0xb9000000, irq 4
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.360000] eth1: Atheros AG71xx at 0xba000000, irq 5
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.670000] ag71xx ag71xx.1: eth1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.680000] TCP cubic registered
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.680000] NET: Registered protocol family 17
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 3.680000] Bridge firewalling registered
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.690000] Ebtables v2.0 registered
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.690000] 8021q: 802.1Q VLAN Support v1.8
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.700000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 3.710000] Freeing unused kernel memory: 220k freed
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.230000] ar71xx: pll_reg 0xb8050010: 0x11110000
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 5.230000] eth0: link up (1000Mbps/Full duplex)
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.330000] Registered led device: d-link:blue:usb
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.330000] Registered led device: d-link:orange:power
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.330000] Registered led device: d-link:blue:power
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.340000] Registered led device: d-link:blue:wps
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.340000] Registered led device: d-link:orange:planet
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 5.340000] Registered led device: d-link:blue:planet
Jan 1 01:00:13 Gargoyle kern.notice kernel: [ 8.640000] JFFS2 notice: (612) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 32 of xref (0 dead, 8 orphan) found.
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 8.780000] eth0: link down
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.250000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.260000] Backport generated by backports.git backports-20140320-37-g5c33da0
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.380000] cfg80211: Calling CRDA to update world regulatory domain
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.390000] cfg80211: World regulatory domain updated:
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.390000] cfg80211: DFS Master region: unset
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.400000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.410000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.420000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.680000] usbcore: registered new interface driver usbfs
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.690000] usbcore: registered new interface driver hub
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 9.690000] usbcore: registered new device driver usb
Jan 1 01:00:13 Gargoyle kern.warn kernel: [ 10.180000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
Jan 1 01:00:13 Gargoyle kern.err kernel: [ 10.190000] ath: phy0: eeprom contains invalid mac address: 09:20:10:32:39:23
Jan 1 01:00:13 Gargoyle kern.err kernel: [ 10.200000] ath: phy0: random mac address will be used: 9a:92:c1:d6:e7:cb
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.210000] ath: EEPROM regdomain: 0x0
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.210000] ath: EEPROM indicates default country code should be used
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.210000] ath: doing EEPROM country->regdmn map search
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.210000] ath: country maps to regdmn code: 0x3a
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.210000] ath: Country alpha2 being used: US
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.210000] ath: Regpair used: 0x3a
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.220000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.230000] Registered led device: ath9k-phy0
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.230000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.230000] cfg80211: Calling CRDA for country: US
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.240000] cfg80211: Regulatory domain changed to country: US
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.240000] cfg80211: DFS Master region: unset
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.250000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.260000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Jan 1 01:00:13 Gargoyle kern.info kernel: [ 10.270000] cfg80211: (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Jan 1 01:00:13 Gargoyle kern.warn kernel: [ 10.270000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.290000] ath: EEPROM regdomain: 0x0
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.290000] ath: EEPROM indicates default country code should be used
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.290000] ath: doing EEPROM country->regdmn map search
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.290000] ath: country maps to regdmn code: 0x3a
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.290000] ath: Country alpha2 being used: US
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.290000] ath: Regpair used: 0x3a
Jan 1 01:00:13 Gargoyle kern.debug kernel: [ 10.300000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Jan 1 01:00:15 Gargoyle kern.info kernel: [ 15.510000] rtl8366s rtl8366s: applying initvals
Jan 1 01:00:16 Gargoyle kern.debug kernel: [ 16.130000] ar71xx: pll_reg 0xb8050010: 0x11110000
Jan 1 01:00:16 Gargoyle kern.info kernel: [ 16.130000] eth0: link up (1000Mbps/Full duplex)
Jan 1 01:00:16 Gargoyle kern.info kernel: [ 16.150000] device eth0.1 entered promiscuous mode
Jan 1 01:00:16 Gargoyle kern.info kernel: [ 16.150000] device eth0 entered promiscuous mode
Jan 1 01:00:16 Gargoyle kern.info kernel: [ 16.160000] br-lan: port 1(eth0.1) entered forwarding state
Jan 1 01:00:16 Gargoyle kern.info kernel: [ 16.170000] br-lan: port 1(eth0.1) entered forwarding state
Jan 1 01:00:16 Gargoyle daemon.notice netifd: Interface 'lan' is now up
Jan 1 01:00:16 Gargoyle daemon.notice netifd: Interface 'loopback' is now up
Jan 1 01:00:16 Gargoyle user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan 1 01:00:16 Gargoyle daemon.notice netifd: wan (938): udhcpc (v1.19.4) started
Jan 1 01:00:16 Gargoyle daemon.notice netifd: wan (938): Sending discover...
Jan 1 01:00:18 Gargoyle kern.info kernel: [ 18.170000] br-lan: port 1(eth0.1) entered forwarding state
Jan 1 01:00:19 Gargoyle daemon.notice netifd: wan (938): Sending discover...
Jan 1 01:00:21 Gargoyle kern.info kernel: [ 21.850000] device wlan1 entered promiscuous mode
Jan 1 01:00:22 Gargoyle kern.info kernel: [ 22.060000] br-lan: port 2(wlan1) entered forwarding state
Jan 1 01:00:22 Gargoyle kern.info kernel: [ 22.060000] br-lan: port 2(wlan1) entered forwarding state
Jan 1 01:00:22 Gargoyle daemon.notice netifd: wan (938): Sending discover...
Jan 1 01:00:24 Gargoyle kern.info kernel: [ 24.060000] br-lan: port 2(wlan1) entered forwarding state
Jan 14 20:27:23 Gargoyle authpriv.info dropbear[1418]: Running in background
Jan 14 20:27:24 Gargoyle daemon.warn httpd_gargoyle[1443]: started as root without requesting chroot(), warning only
Jan 14 20:27:24 Gargoyle daemon.notice httpd_gargoyle[1443]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Jan 14 20:27:24 Gargoyle user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jan 14 20:27:24 Gargoyle user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jan 14 20:27:24 Gargoyle user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq[1483]: started, version 2.66 cachesize 150
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq[1483]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq-dhcp[1483]: DHCP, IP range 192.168.33.100 -- 192.168.33.249, lease time 12h
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq[1483]: using local addresses only for domain lan
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq[1483]: reading /tmp/resolv.conf.auto
Jan 14 20:27:27 Gargoyle daemon.warn dnsmasq[1483]: ignoring nameserver 192.168.33.1 - local interface
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq[1483]: using local addresses only for domain lan
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq[1483]: read /etc/hosts - 2 addresses
Jan 14 20:27:27 Gargoyle daemon.info dnsmasq-dhcp[1483]: read /etc/ethers - 0 addresses
Jan 14 20:27:27 Gargoyle user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Jan 14 20:27:27 Gargoyle user.info sysinit: (Did you specify correct configuration file path?)
Jan 14 20:27:28 Gargoyle user.info sysinit: setting up led USB
Jan 14 20:27:28 Gargoyle user.info sysinit: sh: write error: Invalid argument
Jan 14 20:27:28 Gargoyle user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/d-link:blue:usb/device_name: nonexistent directory
Jan 14 20:27:28 Gargoyle user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/d-link:blue:usb/activity_interval: nonexistent directory
Jan 14 20:27:41 Gargoyle daemon.info dnsmasq-dhcp[1483]: DHCPREQUEST(br-lan) 192.168.22.51 10:9a:dd:70:a4:11
Jan 14 20:27:41 Gargoyle daemon.info dnsmasq-dhcp[1483]: DHCPNAK(br-lan) 192.168.22.51 10:9a:dd:70:a4:11 wrong network
Jan 14 20:27:42 Gargoyle daemon.info dnsmasq-dhcp[1483]: DHCPREQUEST(br-lan) 192.168.33.199 10:9a:dd:70:a4:11
Jan 14 20:27:42 Gargoyle daemon.info dnsmasq-dhcp[1483]: DHCPACK(br-lan) 192.168.33.199 10:9a:dd:70:a4:11
SuccessNic tu nie ma o wykryciu jakiegoś hilinka.
Czekaj - nie zainstalowałeś wersji fat tylko zwykłą? Tam nie ma prawie obsługi usb:
dla routerów bez USB (TP-Link serii TL-WR74x/84x/94x, D-Link i inne) oraz dla WRT160NL factory i DIR825B1 (bez obrazu fat)
- wielojęzyczny interfejs (domyślnie: Angielski i Polski, inne z możliwością instalacji)
- ustawienia regionalne - Polska
- obsługa przycisków
- plugin-gargoyle-logread logi systemowe)
- plugin-gargoyle-wifi-scheduler (harmonogram Wi-Fi)
- plugin-gargoyle-ping-watchdog (monitor połączenia)
- brak obsługi repeatera i UPnP (dla DLINK DIR-6xx)
Dokładnie tak j.w. napisałeś, już doinstalowałem wszystko i działa (interfejs taki jak w poradniku, sam się pokazał w GUI konfiguracji). 
Strony 1
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → DIR-825 Gargoyle 1.6.2.2 konfiguracja E3372 Hilink?
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc