Temat: TL-WR1043ND Nieaktywne porty LAN/WAN
Witam,
trafił mi się router TP-Link'a, z którym nie potrafię sobie dać rady.
Nie wiem co się wcześniej z nim działo, ale podobno było aktualizowane oprogramowanie i sprzęt padł.
Na obecną chwilę router włącza się, zapalają się wszystkie diody led, po chwili gasną, zostaje tylko PWR oraz miga SYS przez jakąś chwilę i także się zapala po paru sekundach. Niepokojące jest to, że mimo podpięcia się do portów LAN jak i WAN na komputerze oraz routerze jest totalny brak reakcji (na routerze nie zaświeca się żadna z diod LAN/WAN, a na komputerze widnieje informacja kabel sieciowy jest odłączony - sprawdzone na dwóch różnych przewodach i komputerach).
Idąc dalej wlutowałem w płytę routera goldpiny na interfejsie rs232 i skomunikowałem się zmin poprzez terminal w celu zdiagnozowania problemu. Po uruchomieniu routera otrzymuję informację od bootloadera oraz widzę całą procedurę startową softu, jednak nic niepokojącego nie widzę. Wklejam poniżej log z konsoli, gdzie widać że router uruchamia się, ale porty LAN mimo to są nieaktywne.
U-Boot 1.1.4 (Mar 19 2014 - 11:06:29)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
chip ID is 0x00000000
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
is_auto_upload_firmware=0
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...
[ 0.000000] Linux version 3.10.49 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #70 Fri Oct 17 22:01:19 CEST 2014
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28588k/32768k available (2367k kernel code, 4180k reserved, 623k data, 272k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.360000] bio: create slab <bio-0> at 0
[ 0.370000] Switching to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.380000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.380000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.390000] TCP: Hash tables configured (established 512 bind 512)
[ 0.390000] TCP: reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 55
[ 0.450000] io scheduler noop registered
[ 0.460000] io scheduler deadline registered (default)
[ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.500000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.500000] console [ttyS0] enabled, bootconsole disabled
[ 0.500000] console [ttyS0] enabled, bootconsole disabled
[ 0.520000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.520000] m25p80 spi0.0: found s25sl064p, expected m25p80
[ 0.530000] m25p80 spi0.0: s25sl064p (8192 Kbytes)
[ 0.540000] 5 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 5 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.550000] 0x000000020000-0x000000130200 : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] 0x000000130200-0x0000007f0000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.590000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.600000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.600000] 0x000000380000-0x0000007f0000 : "rootfs_data"
[ 0.610000] 0x0000007f0000-0x000000800000 : "art"
[ 0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.4
[ 0.740000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.740000] rtl8366rb rtl8366rb: unknown chip id (0000)
[ 0.750000] rtl8366rb rtl8366rb: chip detection failed, err=-19
[ 1.050000] ag71xx ag71xx.0: unable to find MII bus on device 'rtl8366rb'
[ 1.060000] TCP: cubic registered
[ 1.070000] NET: Registered protocol family 17
[ 1.070000] Bridge firewalling registered
[ 1.080000] 8021q: 802.1Q VLAN Support v1.8
[ 1.090000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.100000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
procd: Console is alive
procd: - watchdog -
[ 4.260000] usbcore: registered new interface driver usbfs
[ 4.270000] usbcore: registered new interface driver hub
[ 4.270000] usbcore: registered new device driver usb
[ 4.320000] SCSI subsystem initialized
[ 4.330000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.340000] ehci-platform: EHCI generic platform driver
[ 4.350000] ehci-platform ehci-platform: EHCI Host Controller
[ 4.350000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 4.360000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 4.390000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 4.390000] hub 1-0:1.0: USB hub found
[ 4.400000] hub 1-0:1.0: 1 port detected
[ 4.410000] usbcore: registered new interface driver usb-storage
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
kmod: ran 1 iterations
[ 8.490000] jffs2: notice: (334) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
[ 8.560000] jffs2: notice: (331) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 10.500000] NET: Registered protocol family 10
[ 10.530000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
[ 10.540000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.560000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 10.570000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 10.580000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.630000] xt_time: kernel timezone is -0000
[ 10.690000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.690000] cfg80211: World regulatory domain updated:
[ 10.700000] cfg80211: DFS Master region: unset
[ 10.700000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.710000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.720000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.730000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.740000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.740000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.750000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 10.760000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 10.770000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 10.810000] PPP generic driver version 2.4.2
[ 10.820000] NET: Registered protocol family 24
[ 10.950000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[ 10.960000] cfg80211: Calling CRDA for country: US
[ 10.970000] cfg80211: Regulatory domain changed to country: US
[ 10.970000] cfg80211: DFS Master region: FCC
[ 10.980000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 10.990000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 10.990000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 11.000000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 11.010000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.020000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
procd: - init complete -Aha, próbowałem w konsoli użyć trybu falisafe (led SYS szybko miga) i przywrócić ustawienia fabrycznie 'fistboot', ale niestety nic to nie daje.
Czy można jeszcze ten sprzęt jakoś ożywić, co mogę jeszcze ew. sprawdzić?
Pozdrawiam
