FAQ o OpenWrt | Sprzedam różne routery | Oddam

geos · 2015-07-24 19:28:24

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Temat: P2812HNU-Fx WiFi zniknęło w CC

mam taki wynalazek: http://eko.one.pl/forum/viewtopic.php?p … 17#p143617

wgrałem na niego openwrt wg. wskazówek wiki. użyłem plików z dropboxa, które podał Scotch w ww. wątku. po zalogowaniu do luci widzę interfejs WiFi:

PunBB bbcode test

wgrałem obraz Cezarego dla wersji F1. wifi zniknęło. ki czort? załączam logi z bootowania z putty. uprzejmie proszę o rozwiązanie zagadki.

pozdrawiam
geos

obraz z dropboxa:

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq GRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
P-2812HNU-Fx # setenv nboot 'nand read 0x80800000 0x60000 0x200000; bootm 0x80800000'
P-2812HNU-Fx # setenv bootcmd 'run nboot'
P-2812HNU-Fx # saveenv
Saving Environment to NAND...
Erasing NAND...
Erasing at 0x40000 -- 100% complete.
Writing to NAND... OK
P-2812HNU-Fx #
ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq GRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x60000, size 0x200000
 2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-12-16   8:33:38 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1448308 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.49 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Tue Dec 16 09:32:45 CET 2014
[    0.000000] SoC: GR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00077c51
[    0.000000] Readback ErrCtl register=00077c51
[    0.000000] Memory: 125368k/131072k available (3046k kernel code, 5704k reserved, 1031k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.076000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.080000]   IO 0x000000001ae00000..0x000000001affffff
[    0.096000] bio: create slab <bio-0> at 0
[    0.100000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.104000] usbcore: registered new interface driver usbfs
[    0.108000] usbcore: registered new interface driver hub
[    0.112000] usbcore: registered new device driver usb
[    0.116000] PCI host bridge to bus 0000:00
[    0.120000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.124000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.128000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.132000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.136000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
[    0.140000] Switching to clocksource MIPS
[    0.148000] NET: Registered protocol family 2
[    0.152000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.160000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.164000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.172000] TCP: reno registered
[    0.176000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.188000] NET: Registered protocol family 1
[    0.192000] gptu: totally 6 16-bit timers/counters
[    0.196000] gptu: misc_register on minor 63
[    0.200000] gptu: succeeded to request irq 126
[    0.204000] gptu: succeeded to request irq 127
[    0.208000] gptu: succeeded to request irq 128
[    0.216000] gptu: succeeded to request irq 129
[    0.220000] gptu: succeeded to request irq 130
[    0.224000] gptu: succeeded to request irq 131
[    0.228000] ralink,eeprom ralink_eep.5: using RT2860.eeprom as eeprom
[    0.236000] phy-xrx200 gphy-xrx200.4: requesting lantiq/vr9_phy11g_a2x.bin
[    0.244000] phy-xrx200 gphy-xrx200.4: booting GPHY0 firmware at 78C0000
[    0.252000] phy-xrx200 gphy-xrx200.4: booting GPHY1 firmware at 78C0000
[    0.356000] Wired TLB entries for Linux read_c0_wired() = 0
[    0.364000] config3 0x2424 MT 1
[    0.364000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    0.364000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.388000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.396000] msgmni has been set to 244
[    0.400000] io scheduler noop registered
[    0.404000] io scheduler deadline registered (default)
[    0.412000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    0.420000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.420000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.432000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    0.444000] Scanning device for bad blocks
[    0.536000] 4 ofpart partitions found on MTD device 14000000.nand-parts
[    0.540000] Creating 4 MTD partitions on "14000000.nand-parts":
[    0.544000] 0x000000000000-0x000000040000 : "uboot"
[    0.552000] 0x000000040000-0x000000060000 : "uboot-env"
[    0.556000] 0x000000060000-0x000000260000 : "kernel"
[    0.564000] 0x000000260000-0x000008000000 : "ubi"
[    0.676000] libphy: lantiq,xrx200-mdio: probed
[    0.684000] net-xrx200: invalid MAC, using random
[    0.688000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    0.696000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    0.700000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    0.708000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    0.716000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    0.724000] wdt 1f8803f0.watchdog: Init done
[    0.728000] leds-gpio gpio-leds.7: pins are not configured from the driver
[    0.740000] TCP: cubic registered
[    0.744000] NET: Registered protocol family 17
[    0.748000] 8021q: 802.1Q VLAN Support v1.8
[    0.756000] UBI: auto-attach mtd3
[    0.756000] UBI: attaching mtd3 to ubi0
[    0.944000] UBI: scanning is finished
[    0.968000] UBI: volume 1 ("rootfs_data") re-sized from 9 to 954 LEBs
[    0.972000] UBI: attached mtd3 (name "ubi", size 125 MiB) to ubi0
[    0.976000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    0.984000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    0.992000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    0.996000] UBI: good PEBs: 1005, bad PEBs: 0, corrupted PEBs: 0
[    1.004000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.012000] UBI: max/mean erase counter: 7/5, WL threshold: 4096, image sequence number: 1933928605
[    1.020000] UBI: available PEBs: 0, total reserved PEBs: 1005, PEBs reserved for bad PEB handling: 20
[    1.028000] UBI: background thread "ubi_bgt0d" started, PID 242
[    1.036000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[    1.040000] ubiblock: device ubiblock0_0 (rootfs) set to be root[    1.056000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.064000] Freeing unused kernel memory: 200K (803fe000 - 80430000)
[    1.768000] eth0: port 1 got link
procd: Console is alive
procd: - watchdog -
[    3.800000] SCSI subsystem initialized
[    3.812000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[    3.816000] Chip Version :000d BurstSize=4
[    4.420000] IFXUSB: USB core #0 soft-reset
[    4.720000] IFXUSB: USB core #0 soft-reset
[    4.724000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    4.728000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[    4.736000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[    4.744000] IFXUSB: Init: Power Port (0)
[    4.748000] hub 1-0:1.0: USB hub found
[    4.748000] hub 1-0:1.0: 1 port detected
[    5.256000] IFXUSB: USB core #1 soft-reset
[    5.556000] IFXUSB: USB core #1 soft-reset
[    5.560000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    5.564000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[    5.572000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[    5.580000] IFXUSB: Init: Power Port (0)
[    5.584000] hub 2-0:1.0: USB hub found
[    5.584000] hub 2-0:1.0: 1 port detected
[    5.588000] ifxusb_hcd ifxusb_hcd: requested GPIO 233
[    5.600000] usbcore: registered new interface driver usb-storage
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.116000] UBIFS: default file-system created
[    9.140000] UBIFS: background thread "ubifs_bgt0_1" started, PID 306
[    9.192000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    9.196000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    9.208000] UBIFS: FS size: 121669632 bytes (116 MiB, 943 LEBs), journal size 6064128 bytes (5 MiB, 47 LEBs)
[    9.216000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[    9.224000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID DF5BEE7F-C1D6-4981-B10B-D7261996FEEA, small LPT model
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   10.964000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   11.032000] NET: Registered protocol family 10
[   11.048000] NET: Registered protocol family 8
[   11.048000] NET: Registered protocol family 20
[   11.064000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   11.076000] PPP generic driver version 2.4.2
[   11.092000] nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
[   11.104000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.120000] MEI CPE Driver, Version 1.2.0

[   11.124000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   11.148000]
[   11.148000] Predefined debug level: 2
[   11.160000] fuse init (API version 7.22)
[   11.168000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   11.172000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   11.184000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.196000] Infineon Technologies DEU driver version 2.0.0
[   11.200000] IFX DEU DES initialized (multiblock).
[   11.204000] IFX DEU AES initialized (multiblock).
[   11.212000] IFX DEU ARC4 initialized (multiblock).
[   11.216000] IFX DEU SHA1 initialized.
[   11.220000] IFX DEU MD5 initialized.
[   11.220000] IFX DEU SHA1_HMAC initialized.
[   11.228000] IFX DEU MD5_HMAC initialized.
[   11.248000] NET: Registered protocol family 24
[   11.252000] usbcore: registered new interface driver ums-alauda
[   11.260000] usbcore: registered new interface driver ums-cypress
[   11.268000] usbcore: registered new interface driver ums-datafab
[   11.272000] usbcore: registered new interface driver ums-freecom
[   11.280000] usbcore: registered new interface driver ums-isd200
[   11.288000] usbcore: registered new interface driver ums-jumpshot
[   11.296000] usbcore: registered new interface driver ums-karma
[   11.300000] usbcore: registered new interface driver ums-sddr09
[   11.308000] usbcore: registered new interface driver ums-sddr55
[   11.316000] usbcore: registered new interface driver ums-usbat
[   11.340000] xt_time: kernel timezone is -0000
[   11.368000] cfg80211: Calling CRDA to update world regulatory domain
[   11.404000] cfg80211: World regulatory domain updated:
[   11.408000] cfg80211:  DFS Master region: unset
[   11.412000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   11.420000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   11.428000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   11.436000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   11.444000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   11.452000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   11.460000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   11.468000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   11.476000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   11.544000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   11.548000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   11.556000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT2860.eeprom'.
[   11.564000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   11.572000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   17.836000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   17.840000] ifxmips_ptm: PTM init succeed
[   19.940000] device eth0.1 entered promiscuous mode
[   19.944000] device eth0 entered promiscuous mode
[   19.948000] br-lan: port 1(eth0.1) entered forwarding state
[   19.952000] br-lan: port 1(eth0.1) entered forwarding state
[   21.956000] br-lan: port 1(eth0.1) entered forwarding state
procd: - init complete -



BusyBox v1.22.1 (2014-12-16 09:25:35 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Barrier Breaker, r43483)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/#

obraz od Cezarego:

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq GRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x60000, size 0x200000
 2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.18
   Created:      2015-07-16  20:43:17 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1618177 Bytes = 1.5 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.18 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #4 Thu Jul 16 22:42:58 CEST 2015
[    0.000000] SoC: GR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00077c50
[    0.000000] Readback ErrCtl register=00077c50
[    0.000000] Memory: 124780K/131072K available (3501K kernel code, 154K rwdata, 1036K rodata, 152K init, 206K bss, 6292K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.168000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.172000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.176000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.180000]   IO 0x000000001ae00000..0x000000001affffff
[    0.196000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.200000] usbcore: registered new interface driver usbfs
[    0.204000] usbcore: registered new interface driver hub
[    0.208000] usbcore: registered new device driver usb
[    0.212000] PCI host bridge to bus 0000:00
[    0.216000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.220000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.224000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.228000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.232000] Switched to clocksource MIPS
[    0.236000] NET: Registered protocol family 2
[    0.240000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.248000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.256000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.260000] TCP: reno registered
[    0.264000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.268000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.276000] NET: Registered protocol family 1
[    0.280000] gptu: totally 6 16-bit timers/counters
[    0.288000] gptu: misc_register on minor 63
[    0.292000] gptu: succeeded to request irq 126
[    0.296000] gptu: succeeded to request irq 127
[    0.300000] gptu: succeeded to request irq 128
[    0.304000] gptu: succeeded to request irq 129
[    0.308000] gptu: succeeded to request irq 130
[    0.312000] gptu: succeeded to request irq 131
[    0.316000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[    0.324000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.332000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7920000
[    0.336000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7920000
[    0.444000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.468000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.472000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.488000] msgmni has been set to 243
[    0.492000] io scheduler noop registered
[    0.496000] io scheduler deadline registered (default)
[    0.500000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.508000] console [ttyLTQ0] enabled
[    0.508000] console [ttyLTQ0] enabled
[    0.516000] bootconsole [early0] disabled
[    0.516000] bootconsole [early0] disabled
[    0.528000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.528000] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.528000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    0.540000] Scanning device for bad blocks
[    0.632000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[    0.636000] Creating 4 MTD partitions on "10000000.nand-parts":
[    0.644000] 0x000000000000-0x000000040000 : "uboot"
[    0.648000] 0x000000040000-0x000000060000 : "uboot-env"
[    0.652000] 0x000000060000-0x000000260000 : "kernel"
[    0.660000] 0x000000260000-0x000008000000 : "ubi"
[    0.768000] libphy: lantiq,xrx200-mdio: probed
[    0.784000] net-xrx200: invalid MAC, using random
[    0.852000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    0.988000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.056000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.124000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.128000] wdt 1f8803f0.watchdog: Init done
[    1.136000] TCP: cubic registered
[    1.136000] NET: Registered protocol family 17
[    1.144000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.156000] Bridge firewalling registered
[    1.160000] 8021q: 802.1Q VLAN Support v1.8
[    1.164000] UBI: auto-attach mtd3
[    1.168000] UBI: attaching mtd3 to ubi0
[    1.360000] UBI: scanning is finished
[    1.372000] UBI: attached mtd3 (name "ubi", size 125 MiB) to ubi0
[    1.380000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.384000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.392000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.400000] UBI: good PEBs: 1005, bad PEBs: 0, corrupted PEBs: 0
[    1.404000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.412000] UBI: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 1933928605
[    1.420000] UBI: available PEBs: 0, total reserved PEBs: 1005, PEBs reserved for bad PEB handling: 20
[    1.432000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[    1.436000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    1.444000] UBI: background thread "ubi_bgt0d" star[    1.456000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.460000] Freeing unused kernel memory: 152K (8049a000 - 804c0000)
[    2.500000] init: Console is alive
[    2.500000] init: - watchdog -
[    4.112000] eth0: port 1 got link
[    4.408000] SCSI subsystem initialized
[    4.416000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.424000] ehci-platform: EHCI generic platform driver
[    4.432000] dwc2 1e101000.ifxhcd: requested GPIO 489
[    5.296000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    5.296000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    5.304000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    5.312000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.312000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    5.324000] hub 1-0:1.0: USB hub found
[    5.328000] hub 1-0:1.0: 1 port detected
[    6.192000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    6.192000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    6.200000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    6.208000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    6.208000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    6.220000] hub 2-0:1.0: USB hub found
[    6.224000] hub 2-0:1.0: 1 port detected
[    6.232000] usbcore: registered new interface driver usb-storage
[    6.520000] init: - preinit -
[    7.068000] random: procd urandom read with 111 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.304000] mount_root: loading kmods from internal overlay
[   10.524000] UBIFS: default file-system created
[   10.548000] UBIFS: background thread "ubifs_bgt0_1" started, PID 315
[   10.596000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.604000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.612000] UBIFS: FS size: 119089152 bytes (113 MiB, 923 LEBs), journal size 5935104 bytes (5 MiB, 46 LEBs)
[   10.620000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[   10.628000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C0D2E313-F92A-4667-8177-E39548EB575B, small LPT model
[   10.640000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.644000] block: unable to load configuration (fstab: Entry not found)
[   10.652000] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   10.660000] block: unable to load configuration (fstab: Entry not found)
[   10.664000] block: attempting to load /etc/config/fstab
[   10.676000] block: unable to load configuration (fstab: Entry not found)
[   10.684000] block: no usable configuration
[   10.688000] UBIFS: un-mount UBI device 0, volume 1
[   10.692000] UBIFS: background thread "ubifs_bgt0_1" stops
[   10.724000] UBIFS: background thread "ubifs_bgt0_1" started, PID 317
[   10.776000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.780000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.788000] UBIFS: FS size: 119089152 bytes (113 MiB, 923 LEBs), journal size 5935104 bytes (5 MiB, 46 LEBs)
[   10.800000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[   10.804000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C0D2E313-F92A-4667-8177-E39548EB575B, small LPT model
[   10.896000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.904000] block: unable to load configuration (fstab: Entry not found)
[   10.908000] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[   10.916000] block: unable to load configuration (fstab: Entry not found)
[   10.924000] block: attempting to load /etc/config/fstab
[   10.928000] block: unable to load configuration (fstab: Entry not found)
[   10.936000] block: no usable configuration
[   10.940000] mount_root: overlay filesystem has not been fully initialized yet
[   10.948000] mount_root: switching to jffs2 overlay
[   10.964000] procd: - early -
[   10.964000] procd: - watchdog -
[   11.464000] random: nonblocking pool is initialized
Failed to connect to ubus
[   11.848000] procd: - ubus -
[   12.852000] procd: - init -
Please press Enter to activate this console.
[   14.248000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   14.276000] NET: Registered protocol family 10
[   14.288000] NET: Registered protocol family 8
[   14.292000] NET: Registered protocol family 20
[   14.312000] gre: GRE over IPv4 demultiplexor driver
[   14.316000] ip_gre: GRE over IPv4 tunneling driver
[   14.336000] PPP generic driver version 2.4.2
[   14.352000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.388000] MEI CPE Driver, Version 1.2.0

[   14.388000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   14.424000]
[   14.424000] Predefined debug level: 2
[   14.668000] u32 classifier
[   14.668000]     input device check on
[   14.672000]     Actions configured
[   14.676000] Mirror/redirect action on
[   14.704000] netem: version 1.3
[   14.720000] fuse init (API version 7.23)
[   14.732000] usbcore: registered new interface driver cdc_acm
[   14.736000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   14.748000] usbcore: registered new interface driver cdc_wdm
[   14.752000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   14.760000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   14.772000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.784000] Infineon Technologies DEU driver version 2.0.0
[   14.788000] IFX DEU DES initialized (multiblock).
[   14.792000] IFX DEU AES initialized (multiblock).
[   14.800000] IFX DEU ARC4 initialized (multiblock).
[   14.804000] IFX DEU SHA1 initialized.
[   14.808000] IFX DEU MD5 initialized.
[   14.808000] IFX DEU SHA1_HMAC initialized.
[   14.816000] IFX DEU MD5_HMAC initialized.
[   14.828000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[   14.856000] PPP MPPE Compression module registered
[   14.864000] NET: Registered protocol family 24
[   14.868000] PPTP driver version 0.8.5
[   14.872000] usbcore: registered new interface driver usblp
[   14.888000] usbcore: registered new interface driver usbserial
[   14.892000] usbcore: registered new interface driver usbserial_generic
[   14.900000] usbserial: USB Serial support registered for generic
[   14.968000] xt_time: kernel timezone is -0000
[   14.976000] usbcore: registered new interface driver cdc_ether
[   14.988000] usbcore: registered new interface driver cdc_ncm
[   15.064000] cfg80211: Calling CRDA to update world regulatory domain
[   15.072000] cfg80211: World regulatory domain updated:
[   15.076000] cfg80211:  DFS Master region: unset
[   15.080000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   15.088000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.096000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.104000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   15.112000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   15.120000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   15.128000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   15.136000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   15.144000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   15.168000] usbcore: registered new interface driver huawei_cdc_ncm
[   15.340000] usbcore: registered new interface driver qmi_wwan
[   15.348000] usbcore: registered new interface driver rndis_host
[   15.388000] usbcore: registered new interface driver sierra
[   15.392000] usbserial: USB Serial support registered for Sierra USB modem
[   15.400000] usbcore: registered new interface driver sierra_net
[   15.412000] usbcore: registered new interface driver cdc_mbim
[   15.420000] usbcore: registered new interface driver option
[   15.428000] usbserial: USB Serial support registered for GSM modem (1-port)
[   15.464000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   15.468000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   15.476000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   15.484000] rt2800pci 0000:00:0e.0: Direct firmware load for RT3062.eeprom failed with error -2
[   15.492000] rt2800pci 0000:00:0e.0: Falling back to user helper
[   15.564000] firmware RT3062.eeprom: firmware_loading_store: map pages failed
[   15.568000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[   15.576000] rt2800pci: probe of 0000:00:0e.0 failed with error -11
ioctl ATM_SETESI: No such device
[   25.020000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   25.024000] ifxmips_ptm: PTM init succeed
[   27.400000] device eth0.1 entered promiscuous mode
[   27.404000] device eth0 entered promiscuous mode
[   27.416000] br-lan: port 1(eth0.1) entered forwarding state
[   27.420000] br-lan: port 1(eth0.1) entered forwarding state
[   29.424000] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.23.2 (2015-06-21 14:15:10 CEST) built-in shell (ash)


        _______                     ________        __
       |       |.-----.-----.-----.|  |  |  |.----.|  |_
       |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
       |_______||   __|_____|__|__||________||__|  |____|
                |__| W I R E L E S S   F R E E D O M

 ----------------------------------------------------------------
 |                                                              |
 | OpenWrt Chaos Calmer (r46365)                                |
 | Build time: 2015-07-16 22:40 CEST                            |
 |                                                              |
 | Cezary Jackiewicz (obsy), http://eko.one.pl                  |
 |                                                              |
 ----------------------------------------------------------------
 | Machine: ZyXEL P-2812HNU-F1                                  |
 | Uptime: 0d, 00:00:39                                         |
 | Load: 0.95 0.22 0.07                                         |
 | Flash: total: 106.1MB, free: 101.4MB, used: 0%               |
 | Memory: total: 122.0MB, free: 108.3MB, used: 11%             |
 | WAN:                                                         |
 | LAN: 192.168.1.1                                             |
 ----------------------------------------------------------------
root@OpenWrt:/#

Cezary · 2015-07-24 19:41:20

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Loading EEPROM data from 'RT3062.eeprom

U mnie go nie ma i to dlatego. Dodam w najbliższych buildach

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-24 20:15:22

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

dzięki!

Cezary · 2015-07-24 20:35:04

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Ściągnij sobie do routera ten plik: https://github.com/ScApi/P2812HNUFx-Pre … m?raw=true i zobacz czy po resecie wifi zaskoczy.

Do /lib/firmware go zapisz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-24 21:23:46

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

zrobiłem tak:

# scp /tftpboot/RT3062.eeprom 192.168.1.1:/lib/firmware
root@192.168.1.1's password: 
RT3062.eeprom                                                               100%  512     0.5KB/s   00:00

po restarcie nic się nie zmianiło, nie ma wifi.

EDYCJA: nie przetransferował się czy jak?

root@OpenWrt:/# ls -la /lib/firmware/
drwxrwxr-x    1 root     root           232 Jul 16 22:44 .
drwxrwxr-x    1 root     root           232 Jul 16 22:44 ..
-rw-r--r--    1 root     root             0 Jul 16 22:44 RT3062.eeprom
-rw-rw-r--    1 root     root           512 Feb 22 08:11 RT3092.eeprom
-rw-r--r--    1 root     root          8192 Jul 16 22:41 rt2860.bin
-rw-r--r--    1 root     root          4096 Jul 16 22:41 rt3290.bin
-rw-rw-r--    1 root     root        885524 Feb 22 08:11 vdsl.bin

zrobiłem jeszcze raz. zaraz po transferze jest obecny, znika po restarcie rutera:

root@OpenWrt:/# ls -la /lib/firmware/
drwxrwxr-x    1 root     root           232 Jul 16 22:44 .
drwxrwxr-x    1 root     root           232 Jul 16 22:44 ..
-rw-r--r--    1 root     root           512 Jul 16 22:52 RT3062.eeprom
-rw-rw-r--    1 root     root           512 Feb 22 08:11 RT3092.eeprom
-rw-r--r--    1 root     root          8192 Jul 16 22:41 rt2860.bin
-rw-r--r--    1 root     root          4096 Jul 16 22:41 rt3290.bin
-rw-rw-r--    1 root     root        885524 Feb 22 08:11 vdsl.bin

Cezary · 2015-07-24 21:33:40

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

No nie może Ci znikać

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-24 21:35:59

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

no coś mu się dzieje, że zmienia rozmiar z 512 na 0 można jakoś bez restartu wczytać ten eeprom?

geos · 2015-07-24 21:48:41

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

hahaha! pomyślałem, że może chodzi o wolne miejsce. usunąłem chyba niepotrzebny dla tego modelu F1 plik RT3092.eeprom, wgrałem jeszcze raz RT3062.eeprom, restart i .... bingo! widać wifi! dzięki Cezary! nie wiem co tam trzeba zmienić w obrazach ale ta sztuczka zadziałała.

root@OpenWrt:/# ls -la /lib/firmware/
drwxrwxr-x    1 root     root           304 Jul 16 22:58 .
drwxrwxr-x    1 root     root           232 Jul 16 22:44 ..
-rw-r--r--    1 root     root           512 Jul 16 22:58 RT3062.eeprom
-rw-r--r--    1 root     root          8192 Jul 16 22:41 rt2860.bin
-rw-r--r--    1 root     root          4096 Jul 16 22:41 rt3290.bin
-rw-rw-r--    1 root     root        885524 Feb 22 08:11 vdsl.bin

PunBB bbcode test

Cezary · 2015-07-24 21:51:39

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Ale tam masz megabajty wolnego, więc o jakim wolnym miejscu piszesz?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-24 21:55:15

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

nie wiem Cezary o co może chodzić, ale tak jak widać po restarcie zmienia się wielkość pliku z 512 na 0. usunięcie niepotrzebnego eeproma o takim samym rozmiarze i ponowne wgranie właściwego eeproma zadziałało.

Scotch · 2015-07-24 22:04:33

Scotch
Użytkownik
Nieaktywny

Zarejestrowany: 2014-12-05
Posty: 334

Odp: P2812HNU-Fx WiFi zniknęło w CC

Chyba nie brak miejsca, a RT3092 - przeznaczony do F3 był przyczyną zamieszania

geos · 2015-07-24 22:09:18

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

możliwe. czy do niczego potrzebny eprom 3092 nie może sobie koegzystować w jenym miejscu z 3062 i po prostu być niewykorzystany?

Scotch · 2015-07-24 22:43:23

Scotch
Użytkownik
Nieaktywny

Zarejestrowany: 2014-12-05
Posty: 334

Odp: P2812HNU-Fx WiFi zniknęło w CC

Tego nie wiem, wiem tylko, że wybiórczo czytasz wiki - http://wiki.openwrt.org/toh/zyxel/p2812hnu-fx

Calibration Data
Image downloaded or build from sources don't contain calibration data (this data isn't stored on partition like on other boards).
This file needs to be placed in /lib/firmware folder after flashing, RT3062.eeprom for P2812HNU-F1 and RT3092.eeprom for P2812HNU-F3, without this file wireless will work in 150Mbps mode.

Firmware z dropboxa prawdopodobnie w /lib/firmware miał 'RT2860.eeprom' - stąd widoczne wifi, ale jak piszą z ograniczeniem do 150Mbps. Natomiast u Cezarego zabrakło obu - rezultat kompletny brak wifi

Wiem natomiast, że możliwa jest koegzystencja RT3092.eeprom i RT2860.eeprom w przypadku F3 - muszę sprawdzić, czy poprawia to stabilność WiFi.

Pozdrawiam

geos · 2015-07-24 22:51:04

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

ja po prostu wielu rzeczy nie rozumiem jestem zafascynowany openwrt, miałem jedno podejście 2 lata temu, ale splot czynników doprowadził do tego, że się zniechęciłem. zaczynam jeszcze raz, a że calibration data jest potrzebne to czytałem, ale do głowy mi nie przyszło, że czegoś może brakować w obrazach od Cezarego. poza tym jak się wgrało to i tak po restarcie coś się dzieje dziwnego i zostaje plik o rozmiarze 0. mam nadzieję, że z czasem nauczę się kojarzyć fakty i weryfikować "oczywistości"

Scotch · 2015-07-24 23:06:44

Scotch
Użytkownik
Nieaktywny

Zarejestrowany: 2014-12-05
Posty: 334

Odp: P2812HNU-Fx WiFi zniknęło w CC

geos napisał/a:

... a że calibration data jest potrzebne to czytałem, ale do głowy mi nie przyszło, że czegoś może brakować w obrazach od Cezarego...

No cóż, ja też jestem w ciężkim szoku... zwłaszcza po tym zapewnieniu: http://eko.one.pl/forum/viewtopic.php?p … 22#p143222
Widać wpadki zdarzają się także najlepszym

geos · 2015-07-25 00:43:20

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

dobrze będzie już tam Cezary rozkmini co i jak umknęło.

Cezary · 2015-07-25 06:38:31

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Sorry, F1 nie mam, więc nie na żywca nie sprawdzę czy faktycznie on chodzi.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Scotch · 2015-07-25 07:14:29

Scotch
Użytkownik
Nieaktywny

Zarejestrowany: 2014-12-05
Posty: 334

Odp: P2812HNU-Fx WiFi zniknęło w CC

Myślę, że nawet gdybyś miał ten model, to przy tej ilości routerów (dla których udostępniasz firmware) jest fizyczną niemożliwością sprawdzenie każdego - od tego są użytkownicy!!!
Każdy doskonale to rozumie, a nasze wpisy potraktuj z przymrużeniem oka
Poza tym (jak już nieraz pisałem) zapewniasz najlepszy i natychmiastowy support (co sprawdziło się po raz kolejny).
Pozdrawiam.

Cezary · 2015-07-25 08:00:07

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Zrobiłem i zaktualizowałem obrazy dla P2812:
- dodałem firmware RT3062.eeprom do obrazów ZyXEL P-2812HNU-Fx
- dodałem obrazy initramfs dla ZyXEL P-2812HNU-Fx
- dodałem pliki z uboot dla ZyXEL P-2812HNU-Fx

Pliki z ubootem mają takie nazwy jak wychodzą z OpenWrt. Na F3 obraz testowałem, działa (łączenie w wifi ), na F1 niech ktoś przetestuje.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-25 08:41:34

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

czy stąd należy pobrać pliki?

http://dl.eko.one.pl/luci/chaos_calmer/lantiq/

chciałem się upewnić, bo chociaż pliki sum kontrolnych są z 25.07 to znacznik czasowy pozostałych plików jest z 17.07

Cezary · 2015-07-25 08:43:04

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Bo się aktualizują. Poczekaj jeszcze jedną chwilę, coś jeszcze dorobię.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary · 2015-07-25 09:27:52

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

Już. Dodałem także do sysinfo wyświetlanie info o flash, bo przy ubifs tego brakowało.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-25 10:25:05

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

wgrałem luci-lantiq-xrx200-P2812HNUF1-squashfs-sysupgrade.tar. jest dobrze będę testował dalej i oczywiście powiadomię jak coś zauważę, ale wifi jest i można się połączyć (łączy się nawet z antenami odłączonymi od płyty!)

czy dobrze rozumiem, że:
a) zazwyczaj upgrade przez sysupgrade lub z poziomu luci wgrywając plik *sysupgrade.tar, który zawiera zarówno kernela, ramdysk jak i właściwy firmware
b) uImage to kernel gdyby ktoś chciał podmienić sobie tylko kernel
c) uImage-initramfs to ramdysk potrzebny kernelowi na początek

kiedy ładować squashfs a kiedy ubifs? czytałem to:

Obraz jffs czy squashfs?
Jeżeli zadałeś takie pytanie to stanowczo wybierz ten ze squashfs. Dlaczego? Chociaż by dlatego że jak popsujesz coś w ustawieniach to będziesz mógł wrócić do stanu pierwotnego uruchamiając tzw. tryb failsafe. Później doczytasz czym się te dwa typy systemów plików różnią i jak są zbudowane obrazy OpenWrt.

ale nie jest dla mnie kiedy ubifs a kiedy squashfs? z chcęcią wgrałbym oba do testów, ale nie wiem czy gdy mam squashfs to mogę wgrać ubifs.

poniżej log z squashfs.

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq GRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x60000, size 0x200000
 2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.18
   Created:      2015-07-25   8:08:03 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1618096 Bytes = 1.5 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.18 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #27 Sat Jul 25 10:06:59 CEST 2015
[    0.000000] SoC: GR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00077c50
[    0.000000] Readback ErrCtl register=00077c50
[    0.000000] Memory: 124780K/131072K available (3501K kernel code, 154K rwdata, 1036K rodata, 152K init, 206K bss, 6292K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.168000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.172000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.176000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.180000]   IO 0x000000001ae00000..0x000000001affffff
[    0.196000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.200000] usbcore: registered new interface driver usbfs
[    0.204000] usbcore: registered new interface driver hub
[    0.208000] usbcore: registered new device driver usb
[    0.212000] PCI host bridge to bus 0000:00
[    0.216000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.220000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.224000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.228000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.232000] Switched to clocksource MIPS
[    0.236000] NET: Registered protocol family 2
[    0.240000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.248000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.256000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.260000] TCP: reno registered
[    0.264000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.268000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.276000] NET: Registered protocol family 1
[    0.280000] gptu: totally 6 16-bit timers/counters
[    0.288000] gptu: misc_register on minor 63
[    0.292000] gptu: succeeded to request irq 126
[    0.296000] gptu: succeeded to request irq 127
[    0.300000] gptu: succeeded to request irq 128
[    0.304000] gptu: succeeded to request irq 129
[    0.308000] gptu: succeeded to request irq 130
[    0.312000] gptu: succeeded to request irq 131
[    0.316000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[    0.324000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.332000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7920000
[    0.336000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7920000
[    0.444000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.468000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.472000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.488000] msgmni has been set to 243
[    0.492000] io scheduler noop registered
[    0.496000] io scheduler deadline registered (default)
[    0.500000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.508000] console [ttyLTQ0] enabled
[    0.508000] console [ttyLTQ0] enabled
[    0.516000] bootconsole [early0] disabled
[    0.516000] bootconsole [early0] disabled
[    0.528000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.528000] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.528000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    0.540000] Scanning device for bad blocks
[    0.632000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[    0.636000] Creating 4 MTD partitions on "10000000.nand-parts":
[    0.644000] 0x000000000000-0x000000040000 : "uboot"
[    0.648000] 0x000000040000-0x000000060000 : "uboot-env"
[    0.652000] 0x000000060000-0x000000260000 : "kernel"
[    0.660000] 0x000000260000-0x000008000000 : "ubi"
[    0.768000] libphy: lantiq,xrx200-mdio: probed
[    0.784000] net-xrx200: invalid MAC, using random
[    0.852000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    0.988000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.056000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.124000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.128000] wdt 1f8803f0.watchdog: Init done
[    1.136000] TCP: cubic registered
[    1.136000] NET: Registered protocol family 17
[    1.144000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.156000] Bridge firewalling registered
[    1.160000] 8021q: 802.1Q VLAN Support v1.8
[    1.164000] UBI: auto-attach mtd3
[    1.168000] UBI: attaching mtd3 to ubi0
[    1.360000] UBI: scanning is finished
[    1.372000] UBI: attached mtd3 (name "ubi", size 125 MiB) to ubi0
[    1.380000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.384000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.392000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.400000] UBI: good PEBs: 1005, bad PEBs: 0, corrupted PEBs: 0
[    1.404000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.412000] UBI: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 1933928605
[    1.420000] UBI: available PEBs: 0, total reserved PEBs: 1005, PEBs reserved for bad PEB handling: 20
[    1.432000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[    1.436000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    1.444000] UBI: background thread "ubi_bgt0d" star[    1.456000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.460000] Freeing unused kernel memory: 152K (8049a000 - 804c0000)
[    2.496000] init: Console is alive
[    2.500000] init: - watchdog -
[    4.108000] eth0: port 1 got link
[    4.412000] SCSI subsystem initialized
[    4.420000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.424000] ehci-platform: EHCI generic platform driver
[    4.436000] dwc2 1e101000.ifxhcd: requested GPIO 489
[    5.296000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    5.296000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    5.304000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    5.312000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.312000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    5.324000] hub 1-0:1.0: USB hub found
[    5.328000] hub 1-0:1.0: 1 port detected
[    6.192000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    6.192000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    6.200000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    6.208000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    6.208000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    6.220000] hub 2-0:1.0: USB hub found
[    6.224000] hub 2-0:1.0: 1 port detected
[    6.232000] usbcore: registered new interface driver usb-storage
[    6.520000] init: - preinit -
[    6.976000] random: procd urandom read with 114 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.284000] mount_root: loading kmods from internal overlay
[   10.520000] UBIFS: background thread "ubifs_bgt0_1" started, PID 315
[   10.548000] UBIFS: recovery needed
[   10.644000] UBIFS: recovery completed
[   10.648000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.652000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.660000] UBIFS: FS size: 119089152 bytes (113 MiB, 923 LEBs), journal size 5935104 bytes (5 MiB, 46 LEBs)
[   10.672000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[   10.676000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 0EBB6BDE-AE0D-419D-A04C-1986C6537975, small LPT model
[   10.688000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.700000] block: extroot: not configured
[   10.700000] UBIFS: un-mount UBI device 0, volume 1
[   10.704000] UBIFS: background thread "ubifs_bgt0_1" stops
[   10.712000] random: nonblocking pool is initialized
[   10.740000] UBIFS: background thread "ubifs_bgt0_1" started, PID 318
[   10.820000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   10.824000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   10.832000] UBIFS: FS size: 119089152 bytes (113 MiB, 923 LEBs), journal size 5935104 bytes (5 MiB, 46 LEBs)
[   10.844000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[   10.848000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 0EBB6BDE-AE0D-419D-A04C-1986C6537975, small LPT model
[   10.944000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   10.952000] block: extroot: not configured
[   10.956000] mount_root: switching to jffs2 overlay
[   10.976000] procd: - early -
[   10.976000] procd: - watchdog -
[   11.840000] procd: - ubus -
[   12.868000] procd: - init -
Please press Enter to activate this console.
[   14.168000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   14.196000] NET: Registered protocol family 10
[   14.208000] NET: Registered protocol family 8
[   14.212000] NET: Registered protocol family 20
[   14.236000] gre: GRE over IPv4 demultiplexor driver
[   14.244000] ip_gre: GRE over IPv4 tunneling driver
[   14.256000] PPP generic driver version 2.4.2
[   14.272000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.308000] MEI CPE Driver, Version 1.2.0

[   14.312000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   14.336000]
[   14.336000] Predefined debug level: 2
[   14.512000] u32 classifier
[   14.512000]     input device check on
[   14.516000]     Actions configured
[   14.524000] Mirror/redirect action on
[   14.624000] netem: version 1.3
[   14.644000] fuse init (API version 7.23)
[   14.652000] usbcore: registered new interface driver cdc_acm
[   14.656000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   14.668000] usbcore: registered new interface driver cdc_wdm
[   14.672000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   14.680000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   14.692000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.704000] Infineon Technologies DEU driver version 2.0.0
[   14.712000] IFX DEU DES initialized (multiblock).
[   14.716000] IFX DEU AES initialized (multiblock).
[   14.720000] IFX DEU ARC4 initialized (multiblock).
[   14.724000] IFX DEU SHA1 initialized.
[   14.728000] IFX DEU MD5 initialized.
[   14.732000] IFX DEU SHA1_HMAC initialized.
[   14.736000] IFX DEU MD5_HMAC initialized.
[   14.748000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[   14.776000] PPP MPPE Compression module registered
[   14.784000] NET: Registered protocol family 24
[   14.788000] PPTP driver version 0.8.5
[   14.792000] usbcore: registered new interface driver usblp
[   14.816000] usbcore: registered new interface driver usbserial
[   14.820000] usbcore: registered new interface driver usbserial_generic
[   14.824000] usbserial: USB Serial support registered for generic
[   14.928000] xt_time: kernel timezone is -0000
[   14.932000] usbcore: registered new interface driver cdc_ether
[   14.940000] usbcore: registered new interface driver cdc_ncm
[   15.000000] cfg80211: Calling CRDA to update world regulatory domain
[   15.004000] cfg80211: World regulatory domain updated:
[   15.008000] cfg80211:  DFS Master region: unset
[   15.012000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   15.024000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.032000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.040000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   15.048000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   15.056000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   15.064000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   15.072000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   15.080000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   15.112000] usbcore: registered new interface driver huawei_cdc_ncm
[   15.308000] usbcore: registered new interface driver qmi_wwan
[   15.316000] usbcore: registered new interface driver rndis_host
[   15.344000] usbcore: registered new interface driver sierra
[   15.348000] usbserial: USB Serial support registered for Sierra USB modem
[   15.360000] usbcore: registered new interface driver sierra_net
[   15.372000] usbcore: registered new interface driver cdc_mbim
[   15.380000] usbcore: registered new interface driver option
[   15.384000] usbserial: USB Serial support registered for GSM modem (1-port)
[   15.412000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   15.416000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   15.424000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   15.516000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   15.524000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
ioctl ATM_SETESI: No such device
[   22.776000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   22.780000] ifxmips_ptm: PTM init succeed
[   25.080000] device eth0.1 entered promiscuous mode
[   25.084000] device eth0 entered promiscuous mode
[   25.096000] br-lan: port 1(eth0.1) entered forwarding state
[   25.100000] br-lan: port 1(eth0.1) entered forwarding state
[   25.980000] cfg80211: Calling CRDA for country: PL
[   25.992000] cfg80211: Regulatory domain changed to country: PL
[   25.996000] cfg80211:  DFS Master region: ETSI
[   26.000000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   26.008000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   26.016000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   26.028000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   26.036000] cfg80211:   (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[   26.044000] cfg80211:   (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   27.104000] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.23.2 (2015-06-21 14:15:10 CEST) built-in shell (ash)


        _______                     ________        __
       |       |.-----.-----.-----.|  |  |  |.----.|  |_
       |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
       |_______||   __|_____|__|__||________||__|  |____|
                |__| W I R E L E S S   F R E E D O M

 ----------------------------------------------------------------
 |                                                              |
 | OpenWrt Chaos Calmer 15.05 (r46450)                          |
 | Build time: 2015-07-25 10:05 CEST                            |
 |                                                              |
 | Cezary Jackiewicz (obsy), [url]http://eko.one.pl[/url]                  |
 |                                                              |
 ----------------------------------------------------------------
 | Machine: ZyXEL P-2812HNU-F1                                  |
 | Uptime: 0d, 00:08:47                                         |
 | Load: 0.02 0.07 0.05                                         |
 | Flash: total: 106.1MB, free: 101.3MB, used: 0%               |
 | Memory: total: 122.0MB, free: 107.9MB, used: 11%             |
 | WAN:                                                         |
 | LAN: 192.168.1.1                                             |
 ----------------------------------------------------------------

pozdrawiam,
geos

Cezary · 2015-07-25 10:31:10

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,033

Odp: P2812HNU-Fx WiFi zniknęło w CC

ubifs powoduje że cały system plików jest zapisywalny, tak jak byś extX zrobić. Ubifs robi się na pamięciach nand. Oczywiście ma też to jedną "wadę" - jak coś zepsujesz do zmiany są bezapelacyjnie wprowadzone i nie masz trybu awaryjnego, jak normalnie w komputerze. Usunięcie czy zmiana pliku to usunięcie czy zmiana, nie jest odkładane gdzieś w /overlay bo tego tu nie ma.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

geos · 2015-07-25 11:16:46

geos
Użytkownik
Nieaktywny

Zarejestrowany: 2012-10-17
Posty: 489

Odp: P2812HNU-Fx WiFi zniknęło w CC

oki, czyli tak jakby ubifs to kolejne ogniwo ewolucji z gałęzi plików R/W. poniżej log z ubifs, wifi działa, dzięki! jak coś trzeba jeszcze posprawdzać to proszę o info.

pozdrawiam,
geos

ROM VER: 1.1.4
CFG 06
NAND
NAND Read OK

U-Boot SPL 2013.10-openwrt5 (Nov 18 2014 - 19:54:01)
SPL: initializing NAND flash
SPL: checking U-Boot image
SPL: loading U-Boot to RAM
SPL: decompressing U-Boot with LZO
SPL: jumping to U-Boot


U-Boot 2013.10-openwrt5 (Nov 18 2014 - 19:54:01) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq GRX288 v1.2
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NAND
DRAM:  128 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x60000, size 0x200000
 2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.18
   Created:      2015-07-25   8:08:03 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1618096 Bytes = 1.5 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.18.18 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #27 Sat Jul 25 10:06:59 CEST 2015
[    0.000000] SoC: GR9 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00077c50
[    0.000000] Readback ErrCtl register=00077c50
[    0.000000] Memory: 124780K/131072K available (3501K kernel code, 154K rwdata, 1036K rodata, 152K init, 206K bss, 6292K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] pinctrl core: initialized pinctrl subsystem
[    0.048000] NET: Registered protocol family 16
[    0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.168000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.172000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.176000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.180000]   IO 0x000000001ae00000..0x000000001affffff
[    0.196000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.200000] usbcore: registered new interface driver usbfs
[    0.204000] usbcore: registered new interface driver hub
[    0.208000] usbcore: registered new device driver usb
[    0.212000] PCI host bridge to bus 0000:00
[    0.216000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.220000] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.224000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.228000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.232000] Switched to clocksource MIPS
[    0.236000] NET: Registered protocol family 2
[    0.240000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.248000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.256000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.260000] TCP: reno registered
[    0.264000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.268000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.276000] NET: Registered protocol family 1
[    0.280000] gptu: totally 6 16-bit timers/counters
[    0.288000] gptu: misc_register on minor 63
[    0.292000] gptu: succeeded to request irq 126
[    0.296000] gptu: succeeded to request irq 127
[    0.300000] gptu: succeeded to request irq 128
[    0.304000] gptu: succeeded to request irq 129
[    0.308000] gptu: succeeded to request irq 130
[    0.312000] gptu: succeeded to request irq 131
[    0.316000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[    0.324000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.332000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7920000
[    0.336000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7920000
[    0.444000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.472000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.476000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.488000] msgmni has been set to 243
[    0.492000] io scheduler noop registered
[    0.496000] io scheduler deadline registered (default)
[    0.500000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.508000] console [ttyLTQ0] enabled
[    0.508000] console [ttyLTQ0] enabled
[    0.516000] bootconsole [early0] disabled
[    0.516000] bootconsole [early0] disabled
[    0.528000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[    0.528000] nand: Samsung NAND 128MiB 3,3V 8-bit
[    0.528000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    0.540000] Scanning device for bad blocks
[    0.632000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[    0.636000] Creating 4 MTD partitions on "10000000.nand-parts":
[    0.644000] 0x000000000000-0x000000040000 : "uboot"
[    0.648000] 0x000000040000-0x000000060000 : "uboot-env"
[    0.652000] 0x000000060000-0x000000260000 : "kernel"
[    0.660000] 0x000000260000-0x000008000000 : "ubi"
[    0.768000] libphy: lantiq,xrx200-mdio: probed
[    0.784000] net-xrx200: invalid MAC, using random
[    0.852000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:01, irq=-1)
[    0.988000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.056000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.124000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.128000] wdt 1f8803f0.watchdog: Init done
[    1.136000] TCP: cubic registered
[    1.136000] NET: Registered protocol family 17
[    1.144000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.156000] Bridge firewalling registered
[    1.160000] 8021q: 802.1Q VLAN Support v1.8
[    1.164000] UBI: auto-attach mtd3
[    1.168000] UBI: attaching mtd3 to ubi0
[    1.360000] UBI: scanning is finished
[    1.372000] UBI: attached mtd3 (name "ubi", size 125 MiB) to ubi0
[    1.380000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.384000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.392000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.400000] UBI: good PEBs: 1005, bad PEBs: 0, corrupted PEBs: 0
[    1.404000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.412000] UBI: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 1933928605
[    1.420000] UBI: available PEBs: 0, total reserved PEBs: 1005, PEBs reserved for bad PEB handling: 20
[    1.432000] UBI: background thread "ubi_bgt0d" sta[    1.460000] UBIFS: background thread "ubifs_bgt0_0" started, PID 243
[    1.488000] UBIFS: start fixing up free space
[    1.964000] UBIFS: free space fixup complete
[    1.992000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.996000] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.008000] UBIFS: FS size: 125153280 bytes (119 MiB, 970 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
[    2.016000] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.020000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 40D2B739-1E31-45E2-ACA4-98837FB1E0F8, small LPT model
[    2.048000] VFS: Mounted root (ubifs filesystem) on device 0:10.
[    2.052000] Freeing unused kernel memory: 152K (8049a000 - 804c0000)
[    2.188000] init: Console is alive
[    2.192000] init: - watchdog -
[    2.684000] SCSI subsystem initialized
[    2.708000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.712000] ehci-platform: EHCI generic platform driver
[    2.736000] dwc2 1e101000.ifxhcd: requested GPIO 489
[    3.596000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    3.596000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    3.604000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    3.612000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    3.612000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    3.624000] hub 1-0:1.0: USB hub found
[    3.628000] hub 1-0:1.0: 1 port detected
[    4.492000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    4.492000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    4.500000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    4.508000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    4.508000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    4.520000] hub 2-0:1.0: USB hub found
[    4.524000] hub 2-0:1.0: 1 port detected
[    4.540000] usbcore: registered new interface driver usb-storage
[    4.920000] eth0: port 1 got link
[    5.196000] init: - preinit -
[    5.360000] random: procd urandom read with 19 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.484000] mount_root: mounting /dev/root
[    8.492000] mount_root: loading kmods from internal overlay
[    8.628000] block: attempting to load /etc/config/fstab
[    8.632000] block: unable to load configuration (fstab: Entry not found)
[    8.640000] block: no usable configuration
[    8.652000] procd: - early -
[    8.656000] procd: - watchdog -
Failed to connect to ubus
[    9.232000] procd: - ubus -
[   10.244000] procd: - init -
Please press Enter to activate this console.
[   11.628000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   11.740000] NET: Registered protocol family 10
[   11.760000] NET: Registered protocol family 8
[   11.764000] NET: Registered protocol family 20
[   11.804000] gre: GRE over IPv4 demultiplexor driver
[   11.808000] ip_gre: GRE over IPv4 tunneling driver
[   11.832000] PPP generic driver version 2.4.2
[   11.852000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.952000] MEI CPE Driver, Version 1.2.0

[   11.956000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   12.052000]
[   12.052000] Predefined debug level: 2
[   12.084000] u32 classifier
[   12.084000]     input device check on
[   12.088000]     Actions configured
[   12.096000] Mirror/redirect action on
[   12.156000] netem: version 1.3
[   12.228000] fuse init (API version 7.23)
[   12.268000] usbcore: registered new interface driver cdc_acm
[   12.272000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   12.288000] usbcore: registered new interface driver cdc_wdm
[   12.292000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   12.300000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   12.316000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.336000] Infineon Technologies DEU driver version 2.0.0
[   12.356000] IFX DEU DES initialized (multiblock).
[   12.360000] IFX DEU AES initialized (multiblock).
[   12.368000] IFX DEU ARC4 initialized (multiblock).
[   12.376000] IFX DEU SHA1 initialized.
[   12.376000] IFX DEU MD5 initialized.
[   12.384000] IFX DEU SHA1_HMAC initialized.
[   12.384000] IFX DEU MD5_HMAC initialized.
[   12.412000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[   12.444000] PPP MPPE Compression module registered
[   12.448000] NET: Registered protocol family 24
[   12.456000] PPTP driver version 0.8.5
[   12.460000] usbcore: registered new interface driver usblp
[   12.484000] usbcore: registered new interface driver usbserial
[   12.488000] usbcore: registered new interface driver usbserial_generic
[   12.496000] usbserial: USB Serial support registered for generic
[   12.548000] xt_time: kernel timezone is -0000
[   12.552000] usbcore: registered new interface driver cdc_ether
[   12.560000] usbcore: registered new interface driver cdc_ncm
[   12.648000] cfg80211: Calling CRDA to update world regulatory domain
[   12.656000] usbcore: registered new interface driver huawei_cdc_ncm
[   12.664000] cfg80211: World regulatory domain updated:
[   12.668000] cfg80211:  DFS Master region: unset
[   12.672000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   12.680000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.688000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.696000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   12.704000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.712000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   12.724000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.732000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.740000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   12.948000] usbcore: registered new interface driver qmi_wwan
[   12.956000] usbcore: registered new interface driver rndis_host
[   12.984000] usbcore: registered new interface driver sierra
[   12.988000] usbserial: USB Serial support registered for Sierra USB modem
[   13.000000] usbcore: registered new interface driver sierra_net
[   13.012000] usbcore: registered new interface driver cdc_mbim
[   13.020000] usbcore: registered new interface driver option
[   13.028000] usbserial: USB Serial support registered for GSM modem (1-port)
[   13.072000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   13.076000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   13.084000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
[   13.096000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
[   13.100000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
ioctl ATM_SETESI: No such device
[   19.452000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   19.456000] ifxmips_ptm: PTM init succeed
[   21.924000] device eth0.1 entered promiscuous mode
[   21.928000] device eth0 entered promiscuous mode
[   21.940000] br-lan: port 1(eth0.1) entered forwarding state
[   21.944000] br-lan: port 1(eth0.1) entered forwarding state
[   23.948000] br-lan: port 1(eth0.1) entered forwarding state
[   32.224000] random: nonblocking pool is initialized



BusyBox v1.23.2 (2015-06-21 14:15:10 CEST) built-in shell (ash)


        _______                     ________        __
       |       |.-----.-----.-----.|  |  |  |.----.|  |_
       |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
       |_______||   __|_____|__|__||________||__|  |____|
                |__| W I R E L E S S   F R E E D O M

 ----------------------------------------------------------------
 |                                                              |
 | OpenWrt Chaos Calmer 15.05 (r46450)                          |
 | Build time: 2015-07-25 10:05 CEST                            |
 |                                                              |
 | Cezary Jackiewicz (obsy), http://eko.one.pl                  |
 |                                                              |
 ----------------------------------------------------------------
 | Machine: ZyXEL P-2812HNU-F1                                  |
 | Uptime: 0d, 00:00:45                                         |
 | Load: 0.62 0.16 0.05                                         |
 | Flash: total: 111.6MB, free: 102.4MB, used: 8%               |
 | Memory: total: 122.0MB, free: 109.6MB, used: 10%             |
 | WAN:                                                         |
 | LAN: 192.168.1.1                                             |
 ----------------------------------------------------------------
root@OpenWrt:/#

FAQ o OpenWrt | Sprzedam różne routery | Oddam

P2812HNU-Fx WiFi zniknęło w CC (Strona 1 z 2)

Posty: 1 do 25 z 27

1 Temat przez geos 2015-07-24 19:28:24

Temat: P2812HNU-Fx WiFi zniknęło w CC

2 Odpowiedź przez Cezary 2015-07-24 19:41:20

Odp: P2812HNU-Fx WiFi zniknęło w CC

3 Odpowiedź przez geos 2015-07-24 20:15:22

Odp: P2812HNU-Fx WiFi zniknęło w CC

4 Odpowiedź przez Cezary 2015-07-24 20:35:04

Odp: P2812HNU-Fx WiFi zniknęło w CC

5 Odpowiedź przez geos 2015-07-24 21:23:46 (edytowany przez geos 2015-07-24 21:32:54)

Odp: P2812HNU-Fx WiFi zniknęło w CC

6 Odpowiedź przez Cezary 2015-07-24 21:33:40

Odp: P2812HNU-Fx WiFi zniknęło w CC

7 Odpowiedź przez geos 2015-07-24 21:35:59

Odp: P2812HNU-Fx WiFi zniknęło w CC

8 Odpowiedź przez geos 2015-07-24 21:48:41 (edytowany przez geos 2015-07-24 21:53:37)

Odp: P2812HNU-Fx WiFi zniknęło w CC

9 Odpowiedź przez Cezary 2015-07-24 21:51:39

Odp: P2812HNU-Fx WiFi zniknęło w CC

10 Odpowiedź przez geos 2015-07-24 21:55:15 (edytowany przez geos 2015-07-24 21:55:45)

Odp: P2812HNU-Fx WiFi zniknęło w CC

11 Odpowiedź przez Scotch 2015-07-24 22:04:33

Odp: P2812HNU-Fx WiFi zniknęło w CC

12 Odpowiedź przez geos 2015-07-24 22:09:18 (edytowany przez geos 2015-07-24 22:09:48)

Odp: P2812HNU-Fx WiFi zniknęło w CC

13 Odpowiedź przez Scotch 2015-07-24 22:43:23

Odp: P2812HNU-Fx WiFi zniknęło w CC

14 Odpowiedź przez geos 2015-07-24 22:51:04 (edytowany przez geos 2015-07-24 22:54:09)

Odp: P2812HNU-Fx WiFi zniknęło w CC

15 Odpowiedź przez Scotch 2015-07-24 23:06:44

Odp: P2812HNU-Fx WiFi zniknęło w CC

16 Odpowiedź przez geos 2015-07-25 00:43:20 (edytowany przez geos 2015-07-25 01:26:37)

Odp: P2812HNU-Fx WiFi zniknęło w CC

17 Odpowiedź przez Cezary 2015-07-25 06:38:31

Odp: P2812HNU-Fx WiFi zniknęło w CC

18 Odpowiedź przez Scotch 2015-07-25 07:14:29

Odp: P2812HNU-Fx WiFi zniknęło w CC

19 Odpowiedź przez Cezary 2015-07-25 08:00:07

Odp: P2812HNU-Fx WiFi zniknęło w CC

20 Odpowiedź przez geos 2015-07-25 08:41:34

Odp: P2812HNU-Fx WiFi zniknęło w CC

21 Odpowiedź przez Cezary 2015-07-25 08:43:04

Odp: P2812HNU-Fx WiFi zniknęło w CC

22 Odpowiedź przez Cezary 2015-07-25 09:27:52

Odp: P2812HNU-Fx WiFi zniknęło w CC

23 Odpowiedź przez geos 2015-07-25 10:25:05

Odp: P2812HNU-Fx WiFi zniknęło w CC

24 Odpowiedź przez Cezary 2015-07-25 10:31:10

Odp: P2812HNU-Fx WiFi zniknęło w CC

25 Odpowiedź przez geos 2015-07-25 11:16:46

Odp: P2812HNU-Fx WiFi zniknęło w CC

Posty: 1 do 25 z 27