FAQ o OpenWrt | Sprzedam różne routery | Oddam

mgrlukasz · 2015-05-24 10:37:52

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Temat: OpenWrt Serwer VPN PPTP błąd 807

Witam

Sprzęt TP-Link WDR4300
OpenWrt BB+LUCI

Wykonałem konfigurację serwera VPN PPTP zgodnie z instrukcją http://eko.one.pl/?p=openwrt-pptpd

Niestety nie mogę się połączyć do serwera w Windowsie 7 wyskakuje błąd 807.

Na routerze nie ma logów z serwera PPTP Powinny być w lokalizacji logfile /tmp/pptp-server.log

Celem wyeliminowania problemów po stronie sieci konfiguracji windwsa itp zainstalowałem DD-WRT postawiłem serwer VPN PPTP i wszystko uruchomiło się od szczału.

Głowna sieć 192.168.1.0/24
TP-LinkWDR- 192.168.1.100 jego podsieć 192.168.2.1

Na jednym z komputerów w głównej sieci wykonałem klienta VPN i spinam go do 192.168.1.100.
Na DD-WRT wszystko działa od razu

OpenWrt mam problem błąd 807

Wykonywałem również testy z podłączenia się z innej sieci WAN przekierowany port 1723 a głównym routerze

Serwer VPN PPTP na DD-WRT- Działa
Serwer VPN PPTP na Widnowsie- Działa
Serwer VPN PPTP na OpenWRT- NIE działa

Co mam nie tak w konfiguracji OpenWRT?
Z góry dzięki za pomoc

Plik

chap-secrets

#USERNAME  PROVIDER  PASSWORD  IPADDRESS
user1 * haslo1 *
user2 * haslo2 *

firewall

config rule
        option name PPTP
        option src wan
        option dest_port 1723
        option proto tcp
        option target ACCEPT

    #GRE protocol
config rule
        option src wan
        option dest lan
        option proto gre
        option target ACCEPT

firewall.user

iptables -A input_rule -i ppp+ -j ACCEPT
iptables -A output_rule -o ppp+ -j ACCEPT
# This rule will allow traffic towards internet
iptables -A forwarding_rule -i ppp+ -j ACCEPT

options.pptpd

debug
logfile /tmp/pptp-server.log
auth
name "pptp-server"
lcp-echo-failure 3
lcp-echo-interval 60
default-asyncmap
mtu 1482
mru 1482
nobsdcomp
nodeflate
#noproxyarp
#nomppc
mppe required,no40,no56,stateless
require-mschap-v2
refuse-chap
refuse-mschap
refuse-eap
refuse-pap
proxyarp
ms-dns 192.168.2.1
#plugin radius.so
#radius-config-file /etc/radius.conf

pptpd.conf

debug
option /etc/ppp/options.pptpd
speed 115200
stimeout 10
localip 192.168.2.1
remoteip 192.168.2.140-149
#localip & remoteip are not needed, ip management is done by pppd

Zyxel EX5601-T1

Cezary · 2015-05-24 19:29:19

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

logread co pokazuje?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-24 20:05:59

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Cezary napisał/a:

logread co pokazuje?

logread chodzi o logi systemowe?

Czy coś innego?
Jaka jest ścieżka do tego pliku?

Zyxel EX5601-T1

build000 · 2015-05-24 20:23:01

build000
Zbanowany
Nieaktywny

Zarejestrowany: 2013-06-25
Posty: 2,058

Odp: OpenWrt Serwer VPN PPTP błąd 807

Wykonaj w konsoli terminala (putty, gnome-terminal, xterminal, powłoka systemu linux, i.t.d.) podłączonego do routera (czyli inaczej w systemie routera, w powłoce routera, cmd routera, i.t.d.) polecenie "logread" (czyli wpisz to słowo po znaku zachęty i kliknij ENTER) i wklej w swoim poście wyniki, czyli to co pokarze się w tym danym terminalu po wywołaniu tej komendy.

mgrlukasz · 2015-05-24 20:25:47

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Sun May 24 11:00:58 2015 kern.info kernel: [    5.270000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sun May 24 11:00:58 2015 kern.info kernel: [    5.270000] hub 1-0:1.0: USB hub found
Sun May 24 11:00:58 2015 kern.info kernel: [    5.280000] hub 1-0:1.0: 1 port detected
Sun May 24 11:00:58 2015 kern.info kernel: [    5.280000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sun May 24 11:00:58 2015 kern.info kernel: [    5.290000] usbcore: registered new interface driver usb-storage
Sun May 24 11:00:58 2015 kern.info kernel: [    5.730000] usb 1-1: new high-speed USB device number 2 using ehci-

platform
Sun May 24 11:00:58 2015 kern.info kernel: [    6.070000] hub 1-1:1.0: USB hub found
Sun May 24 11:00:58 2015 kern.info kernel: [    6.070000] hub 1-1:1.0: 4 ports detected
Sun May 24 11:00:58 2015 kern.info kernel: [    7.420000] eth0: link up (1000Mbps/Full duplex)
Sun May 24 11:00:58 2015 kern.notice kernel: [    9.520000] jffs2: notice: (402) jffs2_build_xattr_subsystem: 

complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 24 of xref (0 dead, 0 orphan) found.
Sun May 24 11:00:58 2015 user.info kernel: [    9.540000] block: attempting to load 

/tmp/jffs_cfg/upper/etc/config/fstab
Sun May 24 11:00:58 2015 user.err kernel: [    9.550000] block: unable to load configuration (fstab: Entry not 

found)
Sun May 24 11:00:58 2015 user.info kernel: [    9.550000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
Sun May 24 11:00:58 2015 user.info kernel: [    9.570000] block: extroot: not configured
Sun May 24 11:00:58 2015 kern.notice kernel: [    9.620000] jffs2: notice: (399) jffs2_build_xattr_subsystem: 

complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 24 of xref (0 dead, 0 orphan) found.
Sun May 24 11:00:58 2015 user.info kernel: [    9.780000] block: attempting to load 

/tmp/jffs_cfg/upper/etc/config/fstab
Sun May 24 11:00:58 2015 user.err kernel: [    9.790000] block: unable to load configuration (fstab: Entry not 

found)
Sun May 24 11:00:58 2015 user.info kernel: [    9.800000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
Sun May 24 11:00:58 2015 user.info kernel: [    9.810000] block: extroot: not configured
Sun May 24 11:00:58 2015 kern.info kernel: [    9.830000] eth0: link down
Sun May 24 11:00:58 2015 kern.info kernel: [   13.000000] NET: Registered protocol family 10
Sun May 24 11:00:58 2015 kern.info kernel: [   13.040000] l2tp_core: L2TP core driver, V2.0
Sun May 24 11:00:58 2015 kern.info kernel: [   13.040000] l2tp_netlink: L2TP netlink interface
Sun May 24 11:00:58 2015 kern.info kernel: [   13.060000] gre: GRE over IPv4 demultiplexor driver
Sun May 24 11:00:58 2015 kern.info kernel: [   13.070000] ip_gre: GRE over IPv4 tunneling driver
Sun May 24 11:00:58 2015 kern.info kernel: [   13.080000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.100000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Sun May 24 11:00:58 2015 kern.info kernel: [   13.130000] Loading modules backported from Linux version master-2014

-05-22-0-gf2032ea
Sun May 24 11:00:58 2015 kern.info kernel: [   13.140000] Backport generated by backports.git backports-20140320-37

-g5c33da0
Sun May 24 11:00:58 2015 kern.info kernel: [   13.170000] cfg80211: Calling CRDA to update world regulatory domain
Sun May 24 11:00:58 2015 kern.info kernel: [   13.170000] cfg80211: World regulatory domain updated:
Sun May 24 11:00:58 2015 kern.info kernel: [   13.180000] cfg80211:  DFS Master region: unset
Sun May 24 11:00:58 2015 kern.info kernel: [   13.180000] cfg80211:   (start_freq - end_freq @ bandwidth), 

(max_antenna_gain, max_eirp), (dfs_cac_time)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.190000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.200000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.210000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), 

(N/A, 2000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.230000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), 

(N/A, 2000 mBm), (0 s)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.230000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), 

(N/A, 2000 mBm), (0 s)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.250000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), 

(N/A, 0 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.340000] u32 classifier
Sun May 24 11:00:58 2015 kern.info kernel: [   13.340000]     input device check on
Sun May 24 11:00:58 2015 kern.info kernel: [   13.350000]     Actions configured
Sun May 24 11:00:58 2015 kern.info kernel: [   13.350000] Mirror/redirect action on
Sun May 24 11:00:58 2015 kern.info kernel: [   13.370000] fuse init (API version 7.22)
Sun May 24 11:00:58 2015 kern.info kernel: [   13.430000] usbcore: registered new interface driver cdc_acm
Sun May 24 11:00:58 2015 kern.info kernel: [   13.430000] cdc_acm: USB Abstract Control Model driver for USB modems 

and ISDN adapters
Sun May 24 11:00:58 2015 kern.info kernel: [   13.440000] usbcore: registered new interface driver cdc_wdm
Sun May 24 11:00:58 2015 kern.info kernel: [   13.460000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sun May 24 11:00:58 2015 kern.info kernel: [   13.520000] usbcore: registered new interface driver usblp
Sun May 24 11:00:58 2015 kern.info kernel: [   13.540000] usbcore: registered new interface driver usbserial
Sun May 24 11:00:58 2015 kern.info kernel: [   13.550000] usbcore: registered new interface driver usbserial_generic
Sun May 24 11:00:58 2015 kern.info kernel: [   13.570000] usbserial: USB Serial support registered for generic
Sun May 24 11:00:58 2015 kern.info kernel: [   13.660000] xt_time: kernel timezone is -0000
Sun May 24 11:00:58 2015 kern.info kernel: [   13.770000] usbcore: registered new interface driver cdc_ether
Sun May 24 11:00:58 2015 kern.info kernel: [   13.790000] usbcore: registered new interface driver cdc_ncm
Sun May 24 11:00:58 2015 kern.info kernel: [   13.790000] usbcore: registered new interface driver huawei_cdc_ncm
Sun May 24 11:00:58 2015 kern.info kernel: [   13.810000] PPP generic driver version 2.4.2
Sun May 24 11:00:58 2015 kern.info kernel: [   13.820000] PPP MPPE Compression module registered
Sun May 24 11:00:58 2015 kern.info kernel: [   13.820000] NET: Registered protocol family 24
Sun May 24 11:00:58 2015 kern.info kernel: [   13.830000] PPTP driver version 0.8.5
Sun May 24 11:00:58 2015 kern.info kernel: [   13.850000] usbcore: registered new interface driver qmi_wwan
Sun May 24 11:00:58 2015 kern.info kernel: [   13.850000] usbcore: registered new interface driver rndis_host
Sun May 24 11:00:58 2015 kern.info kernel: [   13.880000] usbcore: registered new interface driver sierra
Sun May 24 11:00:58 2015 kern.info kernel: [   13.880000] usbserial: USB Serial support registered for Sierra USB 

modem
Sun May 24 11:00:58 2015 kern.info kernel: [   13.900000] usbcore: registered new interface driver sierra_net
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.940000] ath: EEPROM regdomain: 0x0
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.940000] ath: EEPROM indicates default country code should be used
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.940000] ath: doing EEPROM country->regdmn map search
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.940000] ath: country maps to regdmn code: 0x3a
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.940000] ath: Country alpha2 being used: US
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.940000] ath: Regpair used: 0x3a
Sun May 24 11:00:58 2015 kern.debug kernel: [   13.960000] ieee80211 phy0: Selected rate control algorithm 

'minstrel_ht'
Sun May 24 11:00:58 2015 kern.info kernel: [   13.960000] cfg80211: Calling CRDA for country: US
Sun May 24 11:00:58 2015 kern.info kernel: [   13.980000] cfg80211: Regulatory domain changed to country: US
Sun May 24 11:00:58 2015 kern.info kernel: [   13.980000] cfg80211:  DFS Master region: FCC
Sun May 24 11:00:58 2015 kern.info kernel: [   13.990000] cfg80211:   (start_freq - end_freq @ bandwidth), 

(max_antenna_gain, max_eirp), (dfs_cac_time)
Sun May 24 11:00:58 2015 kern.info kernel: [   14.000000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 

3000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   14.000000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 

1700 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   14.010000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 

2300 mBm), (0 s)
Sun May 24 11:00:58 2015 kern.info kernel: [   14.020000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 

3000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   14.030000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), 

(N/A, 4000 mBm), (N/A)
Sun May 24 11:00:58 2015 kern.info kernel: [   14.040000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, 

irq=47
Sun May 24 11:00:58 2015 kern.warn kernel: [   14.040000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.060000] ath: EEPROM regdomain: 0x0
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.060000] ath: EEPROM indicates default country code should be used
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.060000] ath: doing EEPROM country->regdmn map search
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.060000] ath: country maps to regdmn code: 0x3a
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.060000] ath: Country alpha2 being used: US
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.060000] ath: Regpair used: 0x3a
Sun May 24 11:00:58 2015 kern.debug kernel: [   14.070000] ieee80211 phy1: Selected rate control algorithm 

'minstrel_ht'
Sun May 24 11:00:58 2015 kern.info kernel: [   14.090000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, 

irq=40
Sun May 24 11:00:58 2015 kern.info kernel: [   14.130000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
Sun May 24 11:00:58 2015 kern.info kernel: [   14.130000] usbcore: registered new interface driver option
Sun May 24 11:00:58 2015 kern.info kernel: [   14.140000] usbserial: USB Serial support registered for GSM modem (1

-port)
Sun May 24 11:01:00 2015 user.emerg syslog: 'radio0' is disabled
Sun May 24 11:01:00 2015 user.emerg syslog: 'radio1' is disabled
Sun May 24 11:01:00 2015 user.emerg syslog: 'radio0' is disabled
Sun May 24 11:01:00 2015 user.emerg syslog: 'radio1' is disabled
Sun May 24 11:01:00 2015 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Sun May 24 11:01:01 2015 user.err syslog: /dev/mtdblock3 is already mounted
Sun May 24 11:01:01 2015 user.emerg syslog: block: /dev/mtdblock3 is already mounted
Sun May 24 11:01:02 2015 authpriv.info dropbear[1240]: Not backgrounding
Sun May 24 11:01:03 2015 user.err syslog: module is already loaded - xt_multiport
Sun May 24 11:01:03 2015 user.err syslog: module is already loaded - xt_comment
Sun May 24 11:01:03 2015 user.err syslog: module is already loaded - xt_length
Sun May 24 11:01:05 2015 user.err syslog: module is already loaded - xt_multiport
Sun May 24 11:01:05 2015 user.err syslog: module is already loaded - xt_comment
Sun May 24 11:01:05 2015 user.err syslog: module is already loaded - xt_length
Sun May 24 11:01:05 2015 kern.info kernel: [   23.450000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sun May 24 11:01:05 2015 kern.info kernel: [   23.450000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Sun May 24 11:01:05 2015 kern.info kernel: [   23.460000] device eth0.1 entered promiscuous mode
Sun May 24 11:01:05 2015 kern.info kernel: [   23.470000] device eth0 entered promiscuous mode
Sun May 24 11:01:05 2015 kern.info kernel: [   23.470000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'lan' is enabled
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'lan' is setting up now
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'lan' is now up
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'loopback' is enabled
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'loopback' is setting up now
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'loopback' is now up
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'wan' is enabled
Sun May 24 11:01:05 2015 kern.info kernel: [   23.520000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Sun May 24 11:01:05 2015 daemon.notice netifd: Network device 'lo' link is up
Sun May 24 11:01:05 2015 daemon.notice netifd: Interface 'loopback' has link connectivity 
Sun May 24 11:01:06 2015 kern.info kernel: [   23.660000] eth0: link up (1000Mbps/Full duplex)
Sun May 24 11:01:06 2015 daemon.notice netifd: Network device 'eth0' link is up
Sun May 24 11:01:06 2015 daemon.notice netifd: VLAN 'eth0.2' link is up
Sun May 24 11:01:06 2015 daemon.notice netifd: Interface 'wan' has link connectivity 
Sun May 24 11:01:06 2015 daemon.notice netifd: Interface 'wan' is setting up now
Sun May 24 11:01:06 2015 daemon.notice netifd: VLAN 'eth0.1' link is up
Sun May 24 11:01:06 2015 kern.info kernel: [   23.710000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sun May 24 11:01:06 2015 kern.info kernel: [   23.710000] br-lan: port 1(eth0.1) entered forwarding state
Sun May 24 11:01:06 2015 kern.info kernel: [   23.720000] br-lan: port 1(eth0.1) entered forwarding state
Sun May 24 11:01:06 2015 kern.info kernel: [   23.730000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Sun May 24 11:01:06 2015 kern.info kernel: [   23.730000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Sun May 24 11:01:06 2015 daemon.notice netifd: Bridge 'br-lan' link is up
Sun May 24 11:01:06 2015 daemon.notice netifd: Interface 'lan' has link connectivity 
Sun May 24 11:01:06 2015 kern.info kernel: [   23.790000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sun May 24 11:01:06 2015 daemon.notice netifd: wan (1548): udhcpc (v1.22.1) started
Sun May 24 11:01:06 2015 daemon.notice netifd: wan (1548): Sending discover...
Sun May 24 11:01:06 2015 daemon.notice netifd: wan (1548): Sending select for XXX.xxx.1.100...
Sun May 24 11:01:07 2015 daemon.notice netifd: wan (1548): Lease of XXX.xxx.1.100 obtained, lease time 86400
Sun May 24 11:01:07 2015 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sun May 24 11:01:07 2015 daemon.notice netifd: Interface 'wan6' is enabled
Sun May 24 11:01:07 2015 daemon.notice netifd: Network alias 'eth0.2' link is up
Sun May 24 11:01:07 2015 daemon.notice netifd: Interface 'wan6' has link connectivity 
Sun May 24 11:01:07 2015 daemon.notice netifd: Interface 'wan6' is setting up now
Sun May 24 11:01:07 2015 daemon.notice netifd: Interface 'wan' is now up
Sun May 24 11:01:08 2015 kern.info kernel: [   25.720000] br-lan: port 1(eth0.1) entered forwarding state
Sun May 24 11:01:08 2015 daemon.warn odhcpd[1196]: DHCPV6 SOLICIT IA_NA from 0001000119e630ff2c44fd68367a on br-lan: 

ok fdc1:c6e5:6511::b05/128 
Sun May 24 11:01:09 2015 daemon.warn odhcpd[1196]: DHCPV6 REQUEST IA_NA from 0001000119e630ff2c44fd68367a on br-lan: 

ok fdc1:c6e5:6511::b05/128 
Sun May 24 11:01:09 2015 daemon.crit xl2tpd[1654]: setsockopt recvref[30]: Protocol not available
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1654]: Using l2tp kernel support.
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1658]: xl2tpd version xl2tpd-1.3.6 started on OpenWrt PID:1658
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1658]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc.
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1658]: Forked by Scott Balmos and David Stipp, (C) 2001
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1658]: Inherited by Jeff McAdams, (C) 2002
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1658]: Forked again by Xelerance (www.xelerance.com) (C) 2006
Sun May 24 11:01:09 2015 daemon.info xl2tpd[1658]: Listening on IP address 0.0.0.0, port 1701
Sun May 24 11:01:10 2015 user.emerg syslog: setting up led USB1
Sun May 24 11:01:10 2015 user.emerg syslog: setting up led USB2
Sun May 24 11:01:10 2015 user.emerg syslog: setting up led WLAN2G
Sun May 24 11:01:10 2015 user.emerg syslog: - init complete -
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: started, version 2.71 cachesize 150
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN 

DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Sun May 24 11:01:13 2015 daemon.info dnsmasq-dhcp[1722]: DHCP, IP range XXX.xxx.2.100 -- XXX.xxx.2.249, lease time 

12h
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: using local addresses only for domain lan
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: reading /tmp/resolv.conf.auto
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: using local addresses only for domain lan
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: using nameserver XXX.xxx.1.1#53
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: read /etc/hosts - 1 addresses
Sun May 24 11:01:13 2015 daemon.info dnsmasq[1722]: read /tmp/hosts/dhcp - 1 addresses
Sun May 24 11:01:13 2015 daemon.info dnsmasq-dhcp[1722]: read /etc/ethers - 0 addresses
Sun May 24 11:01:13 2015 daemon.info dnsmasq-dhcp[1722]: DHCPREQUEST(br-lan) XXX.xxx.2.100 2c:44:fd:68:36:7a 
Sun May 24 11:01:13 2015 daemon.warn dnsmasq-dhcp[1722]: Ignoring domain firemka.local for DHCP host name laptop
Sun May 24 11:01:13 2015 daemon.info dnsmasq-dhcp[1722]: DHCPACK(br-lan) XXX.xxx.2.100 2c:44:fd:68:36:7a laptop
Sun May 24 11:01:13 2015 daemon.err miniupnpd[1763]: could not open lease file: /var/upnp.leases
Sun May 24 11:01:13 2015 daemon.err miniupnpd[1763]: Why did you run me anyway?
Sun May 24 11:01:15 2015 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Sun May 24 11:01:17 2015 daemon.err miniupnpd[2165]: could not open lease file: /var/upnp.leases
Sun May 24 11:01:17 2015 daemon.err miniupnpd[2165]: Why did you run me anyway?
Sun May 24 11:15:19 2015 authpriv.info dropbear[2173]: Child connection from XXX.xxx.2.100:5427
Sun May 24 11:15:22 2015 authpriv.notice dropbear[2173]: Password auth succeeded for 'root' from XXX.xxx.2.100:5427
Sun May 24 11:16:34 2015 authpriv.info dropbear[2173]: Exit (root): Exited normally
Sun May 24 11:16:41 2015 authpriv.info dropbear[2246]: Child connection from XXX.xxx.2.100:5441
Sun May 24 11:16:43 2015 authpriv.notice dropbear[2246]: Password auth succeeded for 'root' from XXX.xxx.2.100:5441

^Croot@OpenWrt:~# logread
Sun May 24 21:11:56 2015 kern.info kernel: [   12.720000] usbserial: USB Serial support registered for generic
Sun May 24 21:11:56 2015 kern.info kernel: [   12.790000] xt_time: kernel timezone is -0000
Sun May 24 21:11:56 2015 kern.info kernel: [   12.820000] usbcore: registered new interface driver cdc_ether
Sun May 24 21:11:56 2015 kern.info kernel: [   12.830000] usbcore: registered new interface driver cdc_ncm
Sun May 24 21:11:56 2015 kern.info kernel: [   12.830000] usbcore: registered new interface driver huawei_cdc_ncm
Sun May 24 21:11:56 2015 kern.info kernel: [   12.860000] PPP generic driver version 2.4.2
Sun May 24 21:11:56 2015 kern.info kernel: [   12.870000] PPP MPPE Compression module registered
Sun May 24 21:11:56 2015 kern.info kernel: [   12.870000] NET: Registered protocol family 24
Sun May 24 21:11:56 2015 kern.info kernel: [   12.880000] PPTP driver version 0.8.5
Sun May 24 21:11:56 2015 kern.info kernel: [   12.900000] usbcore: registered new interface driver qmi_wwan
Sun May 24 21:11:56 2015 kern.info kernel: [   12.920000] usbcore: registered new interface driver rndis_host
Sun May 24 21:11:56 2015 kern.info kernel: [   12.920000] usbcore: registered new interface driver sierra
Sun May 24 21:11:56 2015 kern.info kernel: [   12.940000] usbserial: USB Serial support registered for Sierra USB 

modem
Sun May 24 21:11:56 2015 kern.info kernel: [   12.950000] usbcore: registered new interface driver sierra_net
Sun May 24 21:11:56 2015 kern.debug kernel: [   12.990000] ath: EEPROM regdomain: 0x0
Sun May 24 21:11:56 2015 kern.debug kernel: [   12.990000] ath: EEPROM indicates default country code should be used
Sun May 24 21:11:56 2015 kern.debug kernel: [   12.990000] ath: doing EEPROM country->regdmn map search
Sun May 24 21:11:56 2015 kern.debug kernel: [   12.990000] ath: country maps to regdmn code: 0x3a
Sun May 24 21:11:56 2015 kern.debug kernel: [   12.990000] ath: Country alpha2 being used: US
Sun May 24 21:11:56 2015 kern.debug kernel: [   12.990000] ath: Regpair used: 0x3a
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.010000] ieee80211 phy0: Selected rate control algorithm 

'minstrel_ht'
Sun May 24 21:11:56 2015 kern.info kernel: [   13.010000] cfg80211: Calling CRDA for country: US
Sun May 24 21:11:56 2015 kern.info kernel: [   13.020000] cfg80211: Regulatory domain changed to country: US
Sun May 24 21:11:56 2015 kern.info kernel: [   13.020000] cfg80211:  DFS Master region: FCC
Sun May 24 21:11:56 2015 kern.info kernel: [   13.030000] cfg80211:   (start_freq - end_freq @ bandwidth), 

(max_antenna_gain, max_eirp), (dfs_cac_time)
Sun May 24 21:11:56 2015 kern.info kernel: [   13.040000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 

3000 mBm), (N/A)
Sun May 24 21:11:56 2015 kern.info kernel: [   13.040000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 

1700 mBm), (N/A)
Sun May 24 21:11:56 2015 kern.info kernel: [   13.050000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 

2300 mBm), (0 s)
Sun May 24 21:11:56 2015 kern.info kernel: [   13.060000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 

3000 mBm), (N/A)
Sun May 24 21:11:56 2015 kern.info kernel: [   13.070000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), 

(N/A, 4000 mBm), (N/A)
Sun May 24 21:11:56 2015 kern.info kernel: [   13.080000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, 

irq=47
Sun May 24 21:11:56 2015 kern.warn kernel: [   13.080000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.090000] ath: EEPROM regdomain: 0x0
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.090000] ath: EEPROM indicates default country code should be used
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.090000] ath: doing EEPROM country->regdmn map search
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.100000] ath: country maps to regdmn code: 0x3a
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.100000] ath: Country alpha2 being used: US
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.100000] ath: Regpair used: 0x3a
Sun May 24 21:11:56 2015 kern.debug kernel: [   13.120000] ieee80211 phy1: Selected rate control algorithm 

'minstrel_ht'
Sun May 24 21:11:56 2015 kern.info kernel: [   13.130000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, 

irq=40
Sun May 24 21:11:56 2015 kern.info kernel: [   13.150000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
Sun May 24 21:11:56 2015 kern.info kernel: [   13.170000] usbcore: registered new interface driver option
Sun May 24 21:11:56 2015 kern.info kernel: [   13.180000] usbserial: USB Serial support registered for GSM modem (1

-port)
Sun May 24 21:11:59 2015 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Sun May 24 21:11:59 2015 user.err syslog: /dev/mtdblock3 is already mounted
Sun May 24 21:11:59 2015 user.emerg syslog: block: /dev/mtdblock3 is already mounted
Sun May 24 21:12:00 2015 authpriv.info dropbear[1243]: Not backgrounding
Sun May 24 21:12:01 2015 user.err syslog: module is already loaded - xt_multiport
Sun May 24 21:12:01 2015 user.err syslog: module is already loaded - xt_comment
Sun May 24 21:12:01 2015 user.err syslog: module is already loaded - xt_length
Sun May 24 21:12:02 2015 user.err syslog: module is already loaded - xt_multiport
Sun May 24 21:12:02 2015 user.err syslog: module is already loaded - xt_comment
Sun May 24 21:12:02 2015 user.err syslog: module is already loaded - xt_length
Sun May 24 21:12:03 2015 kern.info kernel: [   22.380000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sun May 24 21:12:03 2015 kern.info kernel: [   22.380000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Sun May 24 21:12:03 2015 kern.info kernel: [   22.400000] device eth0.1 entered promiscuous mode
Sun May 24 21:12:03 2015 kern.info kernel: [   22.410000] device eth0 entered promiscuous mode
Sun May 24 21:12:03 2015 kern.info kernel: [   22.440000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'lan' is enabled
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'lan' is setting up now
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'lan' is now up
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'loopback' is enabled
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'loopback' is setting up now
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'loopback' is now up
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'wan' is enabled
Sun May 24 21:12:03 2015 kern.info kernel: [   22.490000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Sun May 24 21:12:03 2015 daemon.notice netifd: Network device 'lo' link is up
Sun May 24 21:12:03 2015 daemon.notice netifd: Interface 'loopback' has link connectivity
Sun May 24 21:12:03 2015 kern.info kernel: [   22.650000] eth0: link up (1000Mbps/Full duplex)
Sun May 24 21:12:04 2015 daemon.notice netifd: Network device 'eth0' link is up
Sun May 24 21:12:04 2015 daemon.notice netifd: VLAN 'eth0.2' link is up
Sun May 24 21:12:04 2015 daemon.notice netifd: Interface 'wan' has link connectivity
Sun May 24 21:12:04 2015 daemon.notice netifd: Interface 'wan' is setting up now
Sun May 24 21:12:04 2015 daemon.notice netifd: VLAN 'eth0.1' link is up
Sun May 24 21:12:04 2015 kern.info kernel: [   22.700000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sun May 24 21:12:04 2015 kern.info kernel: [   22.700000] br-lan: port 1(eth0.1) entered forwarding state
Sun May 24 21:12:04 2015 kern.info kernel: [   22.710000] br-lan: port 1(eth0.1) entered forwarding state
Sun May 24 21:12:04 2015 kern.info kernel: [   22.720000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Sun May 24 21:12:04 2015 kern.info kernel: [   22.720000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Sun May 24 21:12:04 2015 daemon.notice netifd: Bridge 'br-lan' link is up
Sun May 24 21:12:04 2015 daemon.notice netifd: Interface 'lan' has link connectivity
Sun May 24 21:12:04 2015 kern.info kernel: [   22.790000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sun May 24 21:12:04 2015 daemon.notice netifd: wan (1548): udhcpc (v1.22.1) started
Sun May 24 21:12:05 2015 kern.info kernel: [   23.660000] cfg80211: Calling CRDA for country: PL
Sun May 24 21:12:05 2015 kern.info kernel: [   23.660000] cfg80211: Regulatory domain changed to country: PL
Sun May 24 21:12:05 2015 kern.info kernel: [   23.670000] cfg80211:  DFS Master region: ETSI
Sun May 24 21:12:05 2015 kern.info kernel: [   23.670000] cfg80211:   (start_freq - end_freq @ bandwidth), 

(max_antenna_gain, max_eirp), (dfs_cac_time)
Sun May 24 21:12:05 2015 kern.info kernel: [   23.680000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 21:12:05 2015 kern.info kernel: [   23.690000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 21:12:05 2015 kern.info kernel: [   23.700000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 

2000 mBm), (0 s)
Sun May 24 21:12:05 2015 kern.info kernel: [   23.710000] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 

2700 mBm), (0 s)
Sun May 24 21:12:05 2015 kern.info kernel: [   23.710000] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), 

(N/A, 4000 mBm), (N/A)
Sun May 24 21:12:05 2015 daemon.notice netifd: wan (1548): Sending discover...
Sun May 24 21:12:05 2015 daemon.notice netifd: wan (1548): Sending select for XXX.xxx.1.100...
Sun May 24 21:12:05 2015 daemon.notice netifd: wan (1548): Lease of XXX.xxx.1.100 obtained, lease time 86400
Sun May 24 21:12:06 2015 kern.info kernel: [   24.710000] br-lan: port 1(eth0.1) entered forwarding state
Sun May 24 21:12:06 2015 daemon.notice netifd: Interface 'wan' is now up
Sun May 24 21:12:06 2015 kern.info kernel: [   25.240000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Sun May 24 21:12:06 2015 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sun May 24 21:12:06 2015 kern.info kernel: [   25.260000] device wlan1 entered promiscuous mode
Sun May 24 21:12:06 2015 kern.info kernel: [   25.270000] cfg80211: Calling CRDA for country: US
Sun May 24 21:12:06 2015 kern.info kernel: [   25.280000] cfg80211: Regulatory domain changed to country: US
Sun May 24 21:12:06 2015 kern.info kernel: [   25.280000] cfg80211:  DFS Master region: FCC
Sun May 24 21:12:06 2015 kern.info kernel: [   25.290000] cfg80211:   (start_freq - end_freq @ bandwidth), 

(max_antenna_gain, max_eirp), (dfs_cac_time)
Sun May 24 21:12:06 2015 kern.info kernel: [   25.300000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 

3000 mBm), (N/A)
Sun May 24 21:12:06 2015 kern.info kernel: [   25.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 

1700 mBm), (N/A)
Sun May 24 21:12:06 2015 kern.info kernel: [   25.310000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 

2300 mBm), (0 s)
Sun May 24 21:12:06 2015 kern.info kernel: [   25.320000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 

3000 mBm), (N/A)
Sun May 24 21:12:06 2015 kern.info kernel: [   25.330000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), 

(N/A, 4000 mBm), (N/A)
Sun May 24 21:12:07 2015 kern.info kernel: [   25.860000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Sun May 24 21:12:07 2015 kern.info kernel: [   25.930000] device wlan0 entered promiscuous mode
Sun May 24 21:12:07 2015 kern.info kernel: [   25.940000] br-lan: port 3(wlan0) entered forwarding state
Sun May 24 21:12:07 2015 kern.info kernel: [   25.940000] br-lan: port 3(wlan0) entered forwarding state
Sun May 24 21:12:07 2015 kern.info kernel: [   25.980000] cfg80211: Calling CRDA for country: PL
Sun May 24 21:12:07 2015 kern.info kernel: [   25.990000] cfg80211: Regulatory domain changed to country: PL
Sun May 24 21:12:07 2015 kern.info kernel: [   25.990000] cfg80211:  DFS Master region: ETSI
Sun May 24 21:12:07 2015 kern.info kernel: [   26.000000] cfg80211:   (start_freq - end_freq @ bandwidth), 

(max_antenna_gain, max_eirp), (dfs_cac_time)
Sun May 24 21:12:07 2015 kern.info kernel: [   26.010000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 21:12:07 2015 kern.info kernel: [   26.010000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 

2000 mBm), (N/A)
Sun May 24 21:12:07 2015 kern.info kernel: [   26.020000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 

2000 mBm), (0 s)
Sun May 24 21:12:07 2015 kern.info kernel: [   26.030000] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 

2700 mBm), (0 s)
Sun May 24 21:12:07 2015 kern.info kernel: [   26.040000] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), 

(N/A, 4000 mBm), (N/A)
Sun May 24 21:12:07 2015 kern.info kernel: [   26.260000] br-lan: port 3(wlan0) entered disabled state
Sun May 24 21:12:08 2015 kern.info kernel: [   27.530000] br-lan: port 2(wlan1) entered forwarding state
Sun May 24 21:12:08 2015 kern.info kernel: [   27.530000] br-lan: port 2(wlan1) entered forwarding state
Sun May 24 21:12:08 2015 kern.info kernel: [   27.540000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Sun May 24 21:12:09 2015 kern.info kernel: [   27.720000] br-lan: port 3(wlan0) entered forwarding state
Sun May 24 21:12:09 2015 kern.info kernel: [   27.720000] br-lan: port 3(wlan0) entered forwarding state
Sun May 24 21:12:09 2015 kern.info kernel: [   27.730000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sun May 24 21:12:09 2015 daemon.notice netifd: Network device 'wlan1' link is up
Sun May 24 21:12:09 2015 daemon.crit xl2tpd[1770]: setsockopt recvref[30]: Protocol not available
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1770]: Using l2tp kernel support.
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1796]: xl2tpd version xl2tpd-1.3.6 started on OpenWrt PID:1796
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1796]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc.
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1796]: Forked by Scott Balmos and David Stipp, (C) 2001
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1796]: Inherited by Jeff McAdams, (C) 2002
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1796]: Forked again by Xelerance (www.xelerance.com) (C) 2006
Sun May 24 21:12:09 2015 daemon.info xl2tpd[1796]: Listening on IP address 0.0.0.0, port 1701
Sun May 24 21:12:09 2015 daemon.notice netifd: Network device 'wlan0' link is up
Sun May 24 21:12:09 2015 user.emerg syslog: setting up led USB1
Sun May 24 21:12:09 2015 user.emerg syslog: setting up led USB2
Sun May 24 21:12:09 2015 user.emerg syslog: setting up led WLAN2G
Sun May 24 21:12:10 2015 user.emerg syslog: - init complete -
Sun May 24 21:12:10 2015 kern.info kernel: [   29.530000] br-lan: port 2(wlan1) entered forwarding state
Sun May 24 21:12:11 2015 kern.info kernel: [   29.720000] br-lan: port 3(wlan0) entered forwarding state
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: started, version 2.71 cachesize 150
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN 

DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Sun May 24 21:12:13 2015 daemon.info dnsmasq-dhcp[1882]: DHCP, IP range XXX.xxx.2.100 -- XXX.xxx.2.249, lease time 

12h
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: using local addresses only for domain lan
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: reading /tmp/resolv.conf.auto
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: using local addresses only for domain lan
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: using nameserver XXX.xxx.1.1#53
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: read /etc/hosts - 1 addresses
Sun May 24 21:12:13 2015 daemon.info dnsmasq[1882]: read /tmp/hosts/dhcp - 1 addresses
Sun May 24 21:12:13 2015 daemon.info dnsmasq-dhcp[1882]: read /etc/ethers - 0 addresses
Sun May 24 21:12:14 2015 daemon.err miniupnpd[1923]: could not open lease file: /var/upnp.leases
Sun May 24 21:12:14 2015 daemon.err miniupnpd[1923]: Why did you run me anyway?
Sun May 24 21:12:15 2015 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Sun May 24 21:12:17 2015 daemon.err miniupnpd[2325]: could not open lease file: /var/upnp.leases
Sun May 24 21:12:17 2015 daemon.err miniupnpd[2325]: Why did you run me anyway?
Sun May 24 21:19:11 2015 daemon.info hostapd: wlan1: STA XX:XX:XX:XX:XX IEEE 802.11: authenticated
Sun May 24 21:19:11 2015 daemon.info hostapd: wlan1: STA XX:XX:XX:XX:XX IEEE 802.11: associated (aid 1)
Sun May 24 21:19:11 2015 daemon.info hostapd: wlan1: STA XX:XX:XX:XX:XX WPA: pairwise key handshake completed (RSN)
Sun May 24 21:19:11 2015 daemon.warn odhcpd[1196]: DHCPV6 SOLICIT IA_NA from 0001000119e630ff2c44fd68367a on br-lan: 

ok fdaf:55be:799c::b05/128
Sun May 24 21:19:11 2015 daemon.info dnsmasq[1882]: read /etc/hosts - 1 addresses
Sun May 24 21:19:11 2015 daemon.info dnsmasq[1882]: read /tmp/hosts/odhcpd - 0 addresses
Sun May 24 21:19:11 2015 daemon.info dnsmasq[1882]: read /tmp/hosts/dhcp - 1 addresses
Sun May 24 21:19:11 2015 daemon.info dnsmasq-dhcp[1882]: read /etc/ethers - 0 addresses
Sun May 24 21:19:11 2015 daemon.info dnsmasq-dhcp[1882]: DHCPREQUEST(br-lan) XXX.xxx.2.121 XX:XX:XX:XX:XX
Sun May 24 21:19:11 2015 daemon.warn dnsmasq-dhcp[1882]: Ignoring domain firemka.local for DHCP host name laptop
Sun May 24 21:19:11 2015 daemon.info dnsmasq-dhcp[1882]: DHCPACK(br-lan) XXX.xxx.2.121 XX:XX:XX:XX:XX laptop
Sun May 24 21:19:12 2015 daemon.warn odhcpd[1196]: DHCPV6 REQUEST IA_NA from 0001000119e630ff2c44fd68367a on br-lan: 

ok fdaf:55be:799c::b05/128
Sun May 24 21:19:12 2015 daemon.info dnsmasq[1882]: read /etc/hosts - 1 addresses
Sun May 24 21:19:12 2015 daemon.info dnsmasq[1882]: read /tmp/hosts/odhcpd - 1 addresses
Sun May 24 21:19:12 2015 daemon.info dnsmasq[1882]: read /tmp/hosts/dhcp - 1 addresses
Sun May 24 21:19:12 2015 daemon.info dnsmasq-dhcp[1882]: read /etc/ethers - 0 addresses
Sun May 24 21:19:16 2015 daemon.info dnsmasq-dhcp[1882]: DHCPINFORM(br-lan) XXX.xxx.2.121 XX:XX:XX:XX:XX
Sun May 24 21:19:16 2015 daemon.info dnsmasq-dhcp[1882]: DHCPACK(br-lan) XXX.xxx.2.121 XX:XX:XX:XX:XX laptop
Sun May 24 21:19:46 2015 authpriv.info dropbear[2332]: Child connection from XXX.xxx.2.121:6643
Sun May 24 21:19:49 2015 authpriv.notice dropbear[2332]: Password auth succeeded for 'root' from XXX.xxx.2.121:6643
Sun May 24 21:21:08 2015 authpriv.info dropbear[2452]: Child connection from XXX.xxx.2.121:6675
Sun May 24 21:21:14 2015 authpriv.notice dropbear[2452]: Password auth succeeded for 'root' from XXX.xxx.2.121:6675
Sun May 24 21:22:36 2015 daemon.info dnsmasq-dhcp[1882]: DHCPINFORM(br-lan) XXX.xxx.2.121 XX:XX:XX:XX:XX
Sun May 24 21:22:36 2015 daemon.info dnsmasq-dhcp[1882]: DHCPACK(br-lan) XXX.xxx.2.121 XX:XX:XX:XX:XX laptop

Zyxel EX5601-T1

build000 · 2015-05-24 21:16:37

build000
Zbanowany
Nieaktywny

Zarejestrowany: 2013-06-25
Posty: 2,058

Odp: OpenWrt Serwer VPN PPTP błąd 807

Nie zapomnij poza tym o małej ale ciekawej opcji edycji - nie musisz od razu "całej czwóry" nam ujawniać - typu Twoje IP, adresy fizyczne MAC, i.t.d. (o ile w danej chwili nie będzie to kluczowy parametr przy danym problemie) - jedna wklejka styknie (co prywatne i poufne warto wyiksować). Wystarczy zmienić stosowne parametry na potrzeby tego tematu, w pliku
/etc/config/system:

(...)
option log_size '32'
# lub więcej - domyślnie jest 16 - po wszystkim można przywrócić 
option conloglevel '8'
option cronloglevel '5' 
# domyślnie jest 8 - po wszystkim można przywrócić
(...)

Ten sam efekt uzyskasz przez LuCi w zakładce "System/Logowanie":
Rozmiar bufora loga systemu: 32 (lub więcej - zależy od złożoności problemu)
Poziom logowania: Debug
Poziom logowania Cron`a: Debug (domyślnie jest "Normal")

Po wszystkim przywróć domyślne ustawienia opisane wcześniej (jak to Ci przeszkadza - ta bogata i długa info + zwiększenie zajętości RAM) - taka mała uwaga na zaś w kwestii prezentowania istotnych informacji na potrzeby rozwiązywania problemów przy pomocy użytkowników forum.
Jak w tym i większości przypadków warto polecenie "logread" wykonać najszybciej jak to możliwe po starcie systemu na routerze.

EDIT:
Wracając do meritum sprawy warto przestudiować (pierwszy link z brzega) http://answers.microsoft.com/en-us/wind … 1a5fc12ba6
Przytoczę dla przykładu jeden spośród gąszczu postów, aby wskazać istotę rzeczy:

(...)
Microsoft error codes doesn't really tell you what's wrong. A error code 807 typically is either the client or the server is behind a NAT device and does not pass through GRE protocol 47. If GRE protocol 47 isn't pass through the NAT device you'll get 807. you'll also get 807 if port 1723 isn't forwarded from the NAT device to the VPN server if the server is behind a NAT device. VPN servers usually have packet filters which restrict inbound connection to only PPTP or L2TP.
(...)

lub w naszym rodzimym języku krótka notka stąd:

(...)
Błąd 807
Najprawdopodobniej twój antywirus lub aplikacja firewall blokuje połączenie VPN.
Znane aplikacje, które mogą blokować połączenie VPN to: AVG, BlackIce, Zone Alarm, Avast 5.x
Proszę również zapoznać się z błędem 806 i 721.
Jeżeli próbujesz połączyć się przez klienta OpenVPN zapoznaj się z tym postem:
http://www.vpnonline.pl/forum/viewtopic.php?t=95
(...)

...czyli krótko mówiąc najpierw analiza własnego systemu i wszelkich filtrów/zapór/i.t.d. czy to z poziomu windows czy zainstalowanych dodatków...to tak na dzień dobry

mgrlukasz · 2015-05-25 10:18:32

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

build000 napisał/a:

EDIT:
Wracając do meritum sprawy warto przestudiować (pierwszy link z brzega) http://answers.microsoft.com/en-us/wind … 1a5fc12ba6
Przytoczę dla przykładu jeden spośród gąszczu postów, aby wskazać istotę rzeczy:
(...)
Microsoft error codes doesn't really tell you what's wrong. A error code 807 typically is either the client or the server is behind a NAT device and does not pass through GRE protocol 47. If GRE protocol 47 isn't pass through the NAT device you'll get 807. you'll also get 807 if port 1723 isn't forwarded from the NAT device to the VPN server if the server is behind a NAT device. VPN servers usually have packet filters which restrict inbound connection to only PPTP or L2TP.
(...)
lub w naszym rodzimym języku krótka notka stąd:
(...)
Błąd 807
Najprawdopodobniej twój antywirus lub aplikacja firewall blokuje połączenie VPN.
Znane aplikacje, które mogą blokować połączenie VPN to: AVG, BlackIce, Zone Alarm, Avast 5.x
Proszę również zapoznać się z błędem 806 i 721.
Jeżeli próbujesz połączyć się przez klienta OpenVPN zapoznaj się z tym postem:
http://www.vpnonline.pl/forum/viewtopic.php?t=95
(...)
...czyli krótko mówiąc najpierw analiza własnego systemu i wszelkich filtrów/zapór/i.t.d. czy to z poziomu windows czy zainstalowanych dodatków...to tak na dzień dobry

Dla weryfikacji wgrałem DD-WRT na tego samego routera ustawiłem te same IP uruchomiłem serwer VPN zadziałał od razu.
Postanowiłem szukać problemu po stronie OpenWrt gdyż na DD-WRT zadziałało od razu.

Zyxel EX5601-T1

Cezary · 2015-05-25 10:28:31

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Pokaż z openwrt: netstat -an

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-25 11:40:58

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Cezary napisał/a:

Pokaż z openwrt: netstat -an

Wykonam jak tylko będę przy routerze.

Jak można sprawdzić czy usługa serwer VPN PPTP działa?
Czy ma swoje logi? jak tak to gdzie i jak je uruchomić?
Z góry dzięki

Zyxel EX5601-T1

Cezary · 2015-05-25 12:24:10

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

No właśnie o to chodzi. Bo być może w ogóle nie jest uruchomiona.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

build000 · 2015-05-25 15:23:05

build000
Zbanowany
Nieaktywny

Zarejestrowany: 2013-06-25
Posty: 2,058

Odp: OpenWrt Serwer VPN PPTP błąd 807

mgrlukasz napisał/a:

Dla weryfikacji wgrałem DD-WRT na tego samego routera ustawiłem te same IP uruchomiłem serwer VPN zadziałał od razu.
Postanowiłem szukać problemu po stronie OpenWrt gdyż na DD-WRT zadziałało od razu.

No być może lepiej się spina DD-WRT z Windowsem i jak sugeruje przedmówca w ogóle na DD-WRT działa ten serwer, a na Openwrt w ogóle Ci nie zatrybił...
Tak czy inaczej na DD-WRT działa wiele rzeczy inaczej (przede wszystkim zapora), a na Openwrt inaczej - stąd nie mogą kumać ze sobą winda i Openwrt na tym serwerze pptpd (przynajmniej na domyślnych ustawieniach - dlatego poradziłem Ci żebyś zaczął szukać najpierw w windzie problemów)

mgrlukasz · 2015-05-27 18:32:32

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

netstat -an

Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State
tcp        0      0 0.0.0.0:139             0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:80              0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:53              0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:443             0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:445             0.0.0.0:*               LISTEN
tcp        0    100 192.168.2.1:22          192.168.2.121:9313      ESTABLISHED
tcp        0      0 :::139                  :::*                    LISTEN
tcp        0      0 :::80                   :::*                    LISTEN
tcp        0      0 :::53                   :::*                    LISTEN
tcp        0      0 :::22                   :::*                    LISTEN
tcp        0      0 :::443                  :::*                    LISTEN
tcp        0      0 :::445                  :::*                    LISTEN
udp        0      0 0.0.0.0:53              0.0.0.0:*
udp        0      0 0.0.0.0:67              0.0.0.0:*
udp        0      0 192.168.2.255:137       0.0.0.0:*
udp        0      0 192.168.2.1:137         0.0.0.0:*
udp        0      0 0.0.0.0:137             0.0.0.0:*
udp        0      0 192.168.2.255:138       0.0.0.0:*
udp        0      0 192.168.2.1:138         0.0.0.0:*
udp        0      0 0.0.0.0:138             0.0.0.0:*
udp        0      0 0.0.0.0:1701            0.0.0.0:*
udp        0      0 :::547                  :::*
udp        0      0 :::53                   :::*
raw        0      0 :::58                   ::%4436636:*            58
raw        0      0 :::58                   ::%4436636:*            58
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags       Type       State         I-Node Path
unix  9      [ ]         DGRAM                      1564 /dev/log
unix  2      [ ]         DGRAM                      2593 /var/run/hostapd/wlan1
unix  2      [ ACC ]     STREAM     LISTENING        305 /var/run/ubus.sock
unix  2      [ ACC ]     STREAM     LISTENING       2914 /var/nmbd/unexpected
unix  2      [ ]         DGRAM                      2675 /var/run/hostapd/wlan0
unix  3      [ ]         STREAM     CONNECTED       1567 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1623 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      3735
unix  2      [ ]         DGRAM                      3157
unix  3      [ ]         STREAM     CONNECTED       2693
unix  3      [ ]         STREAM     CONNECTED       1685 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       2577
unix  3      [ ]         STREAM     CONNECTED       1622
unix  2      [ ]         DGRAM                      3661
unix  3      [ ]         STREAM     CONNECTED       2702 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1684
unix  2      [ ]         DGRAM                      2298
unix  3      [ ]         STREAM     CONNECTED        635 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      2970
unix  3      [ ]         STREAM     CONNECTED       2701
unix  2      [ ]         DGRAM                      1675
unix  2      [ ]         DGRAM                      2276
unix  3      [ ]         STREAM     CONNECTED       2578 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1566
unix  3      [ ]         STREAM     CONNECTED        634
unix  3      [ ]         STREAM     CONNECTED       2694 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      1749

Zyxel EX5601-T1

Cezary · 2015-05-27 18:43:28

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Jakoś nie widzę żebyś miał serwer uruchomiony na 1723. Jak go uruchomiłeś?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-27 18:58:08

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Uruchomienie

# /etc/init.d/pptpd enable
# /etc/init.d/pptpd start

Tak jak pisze w poradniku OpenWrt - konfiguracja PPTP

Zyxel EX5601-T1

Cezary · 2015-05-27 19:01:02

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Poradnik był dla AA. Poczekaj.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary · 2015-05-27 19:02:53

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Zobacz jeszcze raz poradnik.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-27 19:21:33

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Nadal w Windowsie błąd 807

Plik /etc/config/pptpd,

config service 'pptpd'
    option 'enabled' '1'
    option 'localip' '192.168.2.1'
    option 'remoteip' '192.168.2.120-130'

config 'login'
    option 'username' 'user1'
    option 'password' 'haslo1'

netstat -an
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State
tcp        0      0 0.0.0.0:139             0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:80              0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:53              0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:1723            0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:443             0.0.0.0:*               LISTEN
tcp        0      0 0.0.0.0:445             0.0.0.0:*               LISTEN
tcp        0    100 192.168.2.1:22          192.168.2.121:10025     ESTABLISHED
tcp        0      0 192.168.2.1:22          192.168.2.121:10022     ESTABLISHED
tcp        0      0 :::139                  :::*                    LISTEN
tcp        0      0 :::80                   :::*                    LISTEN
tcp        0      0 :::53                   :::*                    LISTEN
tcp        0      0 :::22                   :::*                    LISTEN
tcp        0      0 :::443                  :::*                    LISTEN
tcp        0      0 :::445                  :::*                    LISTEN
udp        0      0 0.0.0.0:62768           0.0.0.0:*
udp        0      0 0.0.0.0:53              0.0.0.0:*
udp        0      0 0.0.0.0:67              0.0.0.0:*
udp        0      0 192.168.2.255:137       0.0.0.0:*
udp        0      0 192.168.2.1:137         0.0.0.0:*
udp        0      0 0.0.0.0:137             0.0.0.0:*
udp        0      0 192.168.2.255:138       0.0.0.0:*
udp        0      0 192.168.2.1:138         0.0.0.0:*
udp        0      0 0.0.0.0:138             0.0.0.0:*
udp        0      0 0.0.0.0:1701            0.0.0.0:*
udp        0      0 :::547                  :::*
udp        0      0 :::53                   :::*
raw        0      0 :::58                   ::%4436636:*            58
raw        0      0 :::58                   ::%4436636:*            58
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags       Type       State         I-Node Path
unix  10     [ ]         DGRAM                      1562 /dev/log
unix  2      [ ]         DGRAM                      2658 /var/run/hostapd/wlan1
unix  2      [ ACC ]     STREAM     LISTENING        362 /var/run/ubus.sock
unix  2      [ ACC ]     STREAM     LISTENING       2998 /var/nmbd/unexpected
unix  2      [ ]         DGRAM                      2758 /var/run/hostapd/wlan0
unix  2      [ ]         DGRAM                      3074
unix  3      [ ]         STREAM     CONNECTED       2796 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       2772 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      2318
unix  2      [ ]         DGRAM                      1668
unix  2      [ ]         DGRAM                      3777
unix  3      [ ]         STREAM     CONNECTED       1619
unix  3      [ ]         STREAM     CONNECTED       1564
unix  2      [ ]         DGRAM                      2614
unix  2      [ ]         DGRAM                      2294
unix  3      [ ]         STREAM     CONNECTED       1678
unix  2      [ ]         DGRAM                      3704
unix  3      [ ]         STREAM     CONNECTED       1565 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       2795
unix  3      [ ]         STREAM     CONNECTED        632
unix  3      [ ]         STREAM     CONNECTED       2479
unix  2      [ ]         DGRAM                      1741
unix  3      [ ]         STREAM     CONNECTED       1620 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      3192
unix  3      [ ]         STREAM     CONNECTED       2771
unix  3      [ ]         STREAM     CONNECTED        633 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       2480 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1679 /var/run/ubus.sock

Zyxel EX5601-T1

mgrlukasz · 2015-05-27 19:25:25

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

W poradniku na pewno musi być dwa razy localip ?

# uci set pptpd.pptpd.enabled='1'
# uci set pptpd.pptpd.localip='192.168.1.70'
# uci set pptpd.pptpd.localip='192.168.1.80-89'
# uci commit pptpd

Zyxel EX5601-T1

Cezary · 2015-05-27 19:44:23

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Nie, remoteip.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-27 19:48:24

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Udało się komuś uruchomić serwer VPN PPTP na wersji Barrier Breaker ?

Zyxel EX5601-T1

Cezary · 2015-05-27 19:49:30

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Odblokowałeś firewall na wanie?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-27 19:55:51

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

Taki wpis mam w firewall

firewall
config rule
        option name PPTP
        option src wan
        option dest_port 1723
        option proto tcp
        option target ACCEPT

    #GRE protocol
config rule
        option src wan
        option dest lan
        option proto gre
        option target ACCEPT

Zyxel EX5601-T1

Cezary · 2015-05-27 19:57:13

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

pokaż także: iptables -v -L

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mgrlukasz · 2015-05-27 19:59:16

mgrlukasz
Użytkownik
Nieaktywny

Zarejestrowany: 2015-05-01
Posty: 222

Odp: OpenWrt Serwer VPN PPTP błąd 807

iptables -v -L
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination 
 1880  208K delegate_input  all  --  any    any     anywhere             anywhere

Chain FORWARD (policy DROP 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination 
 1750  625K delegate_forward  all  --  any    any     anywhere             anywhere

Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
 pkts bytes target     prot opt in     out     source               destination 
 1530  421K delegate_output  all  --  any    any     anywhere             anywhere

Chain MINIUPNPD (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain delegate_forward (1 references)
 pkts bytes target     prot opt in     out     source               destination 
 1750  625K forwarding_rule  all  --  any    any     anywhere             anywhere             /* user chain for forwarding */
 1387  586K ACCEPT     all  --  any    any     anywhere             anywhere             ctstate RELATED,ESTABLISHED
  363 38984 zone_lan_forward  all  --  br-lan any     anywhere             anywhere
    0     0 zone_wan_forward  all  --  eth0.2 any     anywhere             anywhere
    0     0 reject     all  --  any    any     anywhere             anywhere    

Chain delegate_input (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 ACCEPT     all  --  lo     any     anywhere             anywhere    
 1880  208K input_rule  all  --  any    any     anywhere             anywhere             /* user chain for input */
 1206  129K ACCEPT     all  --  any    any     anywhere             anywhere             ctstate RELATED,ESTABLISHED
   12   624 syn_flood  tcp  --  any    any     anywhere             anywhere             tcp flags:FIN,SYN,RST,ACK/SYN
  485 41669 zone_lan_input  all  --  br-lan any     anywhere             anywhere
  189 37311 zone_wan_input  all  --  eth0.2 any     anywhere             anywhere

Chain delegate_output (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 ACCEPT     all  --  any    lo      anywhere             anywhere    
 1530  421K output_rule  all  --  any    any     anywhere             anywhere             /* user chain for output */
 1371  406K ACCEPT     all  --  any    any     anywhere             anywhere             ctstate RELATED,ESTABLISHED
   25  4534 zone_lan_output  all  --  any    br-lan  anywhere             anywhere
  134  9815 zone_wan_output  all  --  any    eth0.2  anywhere             anywhere

Chain forwarding_lan_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain forwarding_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 ACCEPT     all  --  ppp+   any     anywhere             anywhere    
    0     0 ACCEPT     all  --  any    ppp+    anywhere             anywhere    

Chain forwarding_wan_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain input_lan_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain input_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 ACCEPT     all  --  ppp+   any     anywhere             anywhere    

Chain input_wan_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain output_lan_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain output_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 ACCEPT     all  --  any    ppp+    anywhere             anywhere    

Chain output_wan_rule (1 references)
 pkts bytes target     prot opt in     out     source               destination 

Chain reject (3 references)
 pkts bytes target     prot opt in     out     source               destination 
    2    80 REJECT     tcp  --  any    any     anywhere             anywhere             reject-with tcp-reset
    4   144 REJECT     all  --  any    any     anywhere             anywhere             reject-with icmp-port-unreachable

Chain syn_flood (1 references)
 pkts bytes target     prot opt in     out     source               destination 
   12   624 RETURN     tcp  --  any    any     anywhere             anywhere             tcp flags:FIN,SYN,RST,ACK/SYN limit: avg 25/sec burst 50
    0     0 DROP       all  --  any    any     anywhere             anywhere    

Chain zone_lan_dest_ACCEPT (3 references)
 pkts bytes target     prot opt in     out     source               destination 
   25  4534 ACCEPT     all  --  any    br-lan  anywhere             anywhere    

Chain zone_lan_forward (1 references)
 pkts bytes target     prot opt in     out     source               destination 
  363 38984 forwarding_lan_rule  all  --  any    any     anywhere             anywhere             /* user chain for forwarding */
  363 38984 zone_wan_dest_ACCEPT  all  --  any    any     anywhere             anywhere             /* forwarding lan -> wan */
    0     0 ACCEPT     all  --  any    any     anywhere             anywhere             ctstate DNAT /* Accept port forwards */
    0     0 zone_lan_dest_ACCEPT  all  --  any    any     anywhere             anywhere

Chain zone_lan_input (1 references)
 pkts bytes target     prot opt in     out     source               destination 
  485 41669 input_lan_rule  all  --  any    any     anywhere             anywhere             /* user chain for input */
    0     0 ACCEPT     all  --  any    any     anywhere             anywhere             ctstate DNAT /* Accept port redirections */
  485 41669 zone_lan_src_ACCEPT  all  --  any    any     anywhere             anywhere

Chain zone_lan_output (1 references)
 pkts bytes target     prot opt in     out     source               destination 
   25  4534 output_lan_rule  all  --  any    any     anywhere             anywhere             /* user chain for output */
   25  4534 zone_lan_dest_ACCEPT  all  --  any    any     anywhere             anywhere

Chain zone_lan_src_ACCEPT (1 references)
 pkts bytes target     prot opt in     out     source               destination 
  485 41669 ACCEPT     all  --  br-lan any     anywhere             anywhere    

Chain zone_wan_dest_ACCEPT (2 references)
 pkts bytes target     prot opt in     out     source               destination 
  497 48799 ACCEPT     all  --  any    eth0.2  anywhere             anywhere    

Chain zone_wan_dest_REJECT (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 reject     all  --  any    eth0.2  anywhere             anywhere    

Chain zone_wan_forward (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    0     0 MINIUPNPD  all  --  any    any     anywhere             anywhere    
    0     0 forwarding_wan_rule  all  --  any    any     anywhere             anywhere             /* user chain for forwarding */
    0     0 zone_lan_dest_ACCEPT  gre  --  any    any     anywhere             anywhere             /* @rule[2] */
    0     0 ACCEPT     all  --  any    any     anywhere             anywhere             ctstate DNAT /* Accept port forwards */
    0     0 zone_wan_dest_REJECT  all  --  any    any     anywhere             anywhere

Chain zone_wan_input (1 references)
 pkts bytes target     prot opt in     out     source               destination 
  189 37311 input_wan_rule  all  --  any    any     anywhere             anywhere             /* user chain for input */
    0     0 ACCEPT     tcp  --  any    any     anywhere             anywhere             tcp dpt:1723 /* PPTP */
    2   119 ACCEPT     tcp  --  any    any     anywhere             anywhere             tcp dpt:www /* GUI */
    0     0 ACCEPT     udp  --  any    any     anywhere             anywhere             udp dpt:bootpc /* Allow-DHCP-Renew */
    0     0 ACCEPT     icmp --  any    any     anywhere             anywhere             icmp echo-request /* Allow-Ping */
    0     0 ACCEPT     tcp  --  any    any     anywhere             anywhere             tcp dpt:ssh /* ssh */
  181 36968 ACCEPT     all  --  any    any     anywhere             anywhere             ctstate DNAT /* Accept port redirections */
    6   224 zone_wan_src_REJECT  all  --  any    any     anywhere             anywhere

Chain zone_wan_output (1 references)
 pkts bytes target     prot opt in     out     source               destination 
  134  9815 output_wan_rule  all  --  any    any     anywhere             anywhere             /* user chain for output */
  134  9815 zone_wan_dest_ACCEPT  all  --  any    any     anywhere             anywhere

Chain zone_wan_src_REJECT (1 references)
 pkts bytes target     prot opt in     out     source               destination 
    6   224 reject     all  --  eth0.2 any     anywhere             anywhere

Zyxel EX5601-T1

Cezary · 2015-05-27 20:13:36

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,014

Odp: OpenWrt Serwer VPN PPTP błąd 807

Łączysz się zza wanu do niego? Bo na firewallu nie ma żadnych pakietów który miałby dostać. Nic nie przyszło, liczniki mają zero.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

FAQ o OpenWrt | Sprzedam różne routery | Oddam

OpenWrt Serwer VPN PPTP błąd 807 (Strona 1 z 2)

Posty: 1 do 25 z 29

1 Temat przez mgrlukasz 2015-05-24 10:37:52 (edytowany przez mgrlukasz 2015-05-24 12:48:21)

Temat: OpenWrt Serwer VPN PPTP błąd 807

2 Odpowiedź przez Cezary 2015-05-24 19:29:19

Odp: OpenWrt Serwer VPN PPTP błąd 807

3 Odpowiedź przez mgrlukasz 2015-05-24 20:05:59

Odp: OpenWrt Serwer VPN PPTP błąd 807

4 Odpowiedź przez build000 2015-05-24 20:23:01 (edytowany przez build000 2015-05-24 20:27:04)

Odp: OpenWrt Serwer VPN PPTP błąd 807

5 Odpowiedź przez mgrlukasz 2015-05-24 20:25:47 (edytowany przez mgrlukasz 2015-05-24 21:41:27)

Odp: OpenWrt Serwer VPN PPTP błąd 807

6 Odpowiedź przez build000 2015-05-24 21:16:37 (edytowany przez build000 2015-05-25 04:54:18)

Odp: OpenWrt Serwer VPN PPTP błąd 807

7 Odpowiedź przez mgrlukasz 2015-05-25 10:18:32

Odp: OpenWrt Serwer VPN PPTP błąd 807

8 Odpowiedź przez Cezary 2015-05-25 10:28:31

Odp: OpenWrt Serwer VPN PPTP błąd 807

9 Odpowiedź przez mgrlukasz 2015-05-25 11:40:58

Odp: OpenWrt Serwer VPN PPTP błąd 807

10 Odpowiedź przez Cezary 2015-05-25 12:24:10

Odp: OpenWrt Serwer VPN PPTP błąd 807

11 Odpowiedź przez build000 2015-05-25 15:23:05 (edytowany przez build000 2015-05-25 15:51:41)

Odp: OpenWrt Serwer VPN PPTP błąd 807

12 Odpowiedź przez mgrlukasz 2015-05-27 18:32:32

Odp: OpenWrt Serwer VPN PPTP błąd 807

13 Odpowiedź przez Cezary 2015-05-27 18:43:28

Odp: OpenWrt Serwer VPN PPTP błąd 807

14 Odpowiedź przez mgrlukasz 2015-05-27 18:58:08 (edytowany przez mgrlukasz 2015-05-27 18:58:47)

Odp: OpenWrt Serwer VPN PPTP błąd 807

15 Odpowiedź przez Cezary 2015-05-27 19:01:02

Odp: OpenWrt Serwer VPN PPTP błąd 807

16 Odpowiedź przez Cezary 2015-05-27 19:02:53

Odp: OpenWrt Serwer VPN PPTP błąd 807

17 Odpowiedź przez mgrlukasz 2015-05-27 19:21:33

Odp: OpenWrt Serwer VPN PPTP błąd 807

18 Odpowiedź przez mgrlukasz 2015-05-27 19:25:25

Odp: OpenWrt Serwer VPN PPTP błąd 807

19 Odpowiedź przez Cezary 2015-05-27 19:44:23

Odp: OpenWrt Serwer VPN PPTP błąd 807

20 Odpowiedź przez mgrlukasz 2015-05-27 19:48:24

Odp: OpenWrt Serwer VPN PPTP błąd 807

21 Odpowiedź przez Cezary 2015-05-27 19:49:30

Odp: OpenWrt Serwer VPN PPTP błąd 807

22 Odpowiedź przez mgrlukasz 2015-05-27 19:55:51

Odp: OpenWrt Serwer VPN PPTP błąd 807

23 Odpowiedź przez Cezary 2015-05-27 19:57:13

Odp: OpenWrt Serwer VPN PPTP błąd 807

24 Odpowiedź przez mgrlukasz 2015-05-27 19:59:16

Odp: OpenWrt Serwer VPN PPTP błąd 807

25 Odpowiedź przez Cezary 2015-05-27 20:13:36

Odp: OpenWrt Serwer VPN PPTP błąd 807

Posty: 1 do 25 z 29