• Zarejestrowany: 2014-10-09
  • Posty: 186

Temat: TP LINK WR710N i LUCI

czy z tej str
http://dl.eko.one.pl/luci/barrier_breaker/ar71xx/
pobiorę pełne Luci do WR710N i czy ma znaczenie v1 czy to v2?

2 Odpowiedź przez simono

  • simono
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-08-10
  • Posty: 596

Odp: TP LINK WR710N i LUCI

Wersja v1 lub v2 to wersja hardware sprzętowa routera więc jest to ważne. Jaką masz wersję możesz na przykład sprawdzić na nalepce pod routerem lub na stronie zarządzania swoim routerem. Jeśli jest na tej stronie obraz dla Twojego routera to będzie pełne Luci z dodatkami od Cezarego.

3 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

to wiem ,
jak dotrze to sprawdze

4 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

Wersja routera to   v.1.2

5 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

Czyli instaluj to z 710n-v1 w nazwie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

6 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

thx
robi sie to tak samo jak gorgulca?

7 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

Tak.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

8 Odpowiedź przez mrrowek (edytowany przez mrrowek 2015-04-22 09:13:20)

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

jak w luci ustawić hilibka w LTE?
zeby działalo tak jak w gorgulcu

9 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

Zmień wan na eth2 czy jaki tam masz kolejny interfejs. I to cała konfiguracja.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

10 Odpowiedź przez mrrowek (edytowany przez mrrowek 2015-04-22 09:37:00)

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

ale w jakiej zakladce?
jesli mozna prosic to tak lopatologicznie

11 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

Łopatologicznie: http://eko.one.pl/?p=openwrt-3g#obsugam … ysieciowej

Za dużo czasu bym spędził gdybym miał tłumaczyć gdzie to w gui zrobić.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

12 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

teraz mam juz wiekszy problem
cos poklikałem coś ponaciskalem rozłaczyłem się i nie mogę się zalogować na router

13 Odpowiedź przez pepe2k

  • pepe2k
  • pepe2k
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-10-29
  • Posty: 5,028

Odp: TP LINK WR710N i LUCI

mrrowek napisał/a:

teraz mam juz wiekszy problem
cos poklikałem coś ponaciskalem rozłaczyłem się i nie mogę się zalogować na router

To teraz trzeba coś odklikać, odcisnąć, połączyć i będzie działać.

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

smile failsafe użyj, też opisane na eko.one.pl.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

15 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

reset pomógl

zamieszczam log
2014.04 unknown) ) #9 Sat Mar 28 08:55:37 CET 2015
[    0.000000] MyLoader: sysp=ad2c3173, boardp=242d95ab, parts=ddad436b
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.00  0.000000] Linux version 3.10.49 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-0000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 80338b60, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR710N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28588k/32768k available (2386k kernel code, 4180k reserved, 620k data, 256k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is TP-LINK TL-WR710N v1
[    0.550000] bio: create slab <bio-0> at 0
[    0.560000] Switching to clocksource MIPS
[    0.570000] NET: Registered protocol family 2
[    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.570000] TCP: Hash tables configured (established 512 bind 512)
[    0.580000] TCP: reno registered
[    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.600000] NET: Registered protocol family 1
[    0.600000] PCI: CLS 0 bytes, default 32
[    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.640000] msgmni has been set to 55
[    0.640000] io scheduler noop registered
[    0.640000] io scheduler deadline registered (default)
[    0.650000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.670000] console [ttyATH0] enabled, bootconsole disabled
[    0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.690000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.690000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.700000] 5 tp-link partitions found on MTD device spi0.0
[    0.700000] Creating 5 MTD partitions on "spi0.0":
[    0.710000] 0x000000000000-0x000000020000 : "u-boot"
[    0.720000] 0x000000020000-0x00000013031c : "kernel"
[    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] 0x00000013031c-0x0000007f0000 : "rootfs"
[    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.750000] mtd: device 2 (rootfs) set to be root filesystem
[    0.760000] 1 squashfs-split partitions found on MTD device rootfs
[    0.760000] 0x000000670000-0x0000007f0000 : "rootfs_data"
[    0.770000] 0x0000007f0000-0x000000800000 : "art"
[    0.770000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.800000] libphy: ag71xx_mdio: probed
[    1.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.910000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
[    2.950000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.950000] TCP: cubic registered
[    2.960000] NET: Registered protocol family 17
[    2.960000] Bridge firewalling registered
[    2.960000] 8021q: 802.1Q VLAN Support v1.8
[    2.970000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    2.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.990000] Freeing unused kernel memory: 256K (80350000 - 80390000)
[    7.210000] usbcore: registered new interface driver usbfs
[    7.220000] usbcore: registered new interface driver hub
[    7.220000] usbcore: registered new device driver usb
[    7.270000] SCSI subsystem initialized
[    7.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.290000] ehci-platform: EHCI generic platform driver
[    7.300000] ehci-platform ehci-platform: EHCI Host Controller
[    7.300000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    7.310000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    7.340000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    7.340000] hub 1-0:1.0: USB hub found
[    7.340000] hub 1-0:1.0: 1 port detected
[    7.350000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.360000] usbcore: registered new interface driver usb-storage
[    7.890000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    8.340000] usb-storage 1-1:1.0: USB Mass Storage device detected
[    8.350000] scsi0 : usb-storage 1-1:1.0
[    9.350000] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[    9.360000] scsi 0:0:0:1: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
[    9.370000] sd 0:0:0:1: [sda] Attached SCSI removable disk
[   11.090000] eth1: link up (1000Mbps/Full duplex)
[   13.270000] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 52 of xref (0 dead, 28 orphan) found.
[   13.290000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   13.290000] block: unable to load configuration (fstab: Entry not found)
[   13.300000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   13.320000] block: extroot: not configured
[   13.360000] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 52 of xref (0 dead, 28 orphan) found.
[   13.610000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   13.610000] block: unable to load configuration (fstab: Entry not found)
[   13.620000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   13.630000] block: extroot: not configured
[   13.660000] eth1: link down
[   18.310000] NET: Registered protocol family 10
[   18.350000] l2tp_core: L2TP core driver, V2.0
[   18.360000] l2tp_netlink: L2TP netlink interface
[   18.370000] gre: GRE over IPv4 demultiplexor driver
[   18.390000] ip_gre: GRE over IPv4 tunneling driver
[   18.410000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
[   18.430000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.470000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   18.470000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   18.520000] cfg80211: Calling CRDA to update world regulatory domain
[   18.520000] cfg80211: World regulatory domain updated:
[   18.530000] cfg80211:  DFS Master region: unset
[   18.530000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   18.540000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   18.550000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   18.560000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   18.570000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   18.570000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   18.580000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   18.590000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   18.600000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   18.720000] u32 classifier
[   18.720000]     input device check on
[   18.720000]     Actions configured
[   18.730000] Mirror/redirect action on
[   18.750000] fuse init (API version 7.22)
[   18.820000] usbcore: registered new interface driver cdc_acm
[   18.820000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   18.840000] usbcore: registered new interface driver cdc_wdm
[   18.860000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.920000] usbcore: registered new interface driver usblp
[   18.960000] usbcore: registered new interface driver usbserial
[   18.970000] usbcore: registered new interface driver usbserial_generic
[   18.990000] usbserial: USB Serial support registered for generic
[   19.070000] xt_time: kernel timezone is -0000
[   19.090000] usbcore: registered new interface driver cdc_ether
[   19.110000] usbcore: registered new interface driver cdc_ncm
[   19.130000] usbcore: registered new interface driver huawei_cdc_ncm
[   19.170000] PPP generic driver version 2.4.2
[   19.170000] PPP MPPE Compression module registered
[   19.190000] NET: Registered protocol family 24
[   19.190000] PPTP driver version 0.8.5
[   19.210000] usbcore: registered new interface driver qmi_wwan
[   19.230000] usbcore: registered new interface driver rndis_host
[   19.230000] usbcore: registered new interface driver sierra
[   19.250000] usbserial: USB Serial support registered for Sierra USB modem
[   19.250000] usbcore: registered new interface driver sierra_net
[   19.290000] ath: EEPROM regdomain: 0x0
[   19.290000] ath: EEPROM indicates default country code should be used
[   19.290000] ath: doing EEPROM country->regdmn map search
[   19.290000] ath: country maps to regdmn code: 0x3a
[   19.290000] ath: Country alpha2 being used: US
[   19.290000] ath: Regpair used: 0x3a
[   19.310000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   19.310000] cfg80211: Calling CRDA for country: US
[   19.320000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   19.330000] cfg80211: Regulatory domain changed to country: US
[   19.330000] cfg80211:  DFS Master region: FCC
[   19.340000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   19.340000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   19.350000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[   19.360000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[   19.370000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   19.380000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   19.390000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   19.410000] usbcore: registered new interface driver option
[   19.410000] usbserial: USB Serial support registered for GSM modem (1-port)
[   25.220000] usb 1-1: USB disconnect, device number 2
[   25.800000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[   25.960000] cdc_ether 1-1:1.0 eth2: register 'cdc_ether' at usb-ehci-platform-1, CDC Ethernet Device, 0c:5b:8f:27:9a:64
[   26.070000] usb-storage 1-1:1.2: USB Mass Storage device detected
[   26.070000] scsi1 : usb-storage 1-1:1.2
[   27.480000] scsi 1:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
[   27.550000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[   35.290000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   35.290000] device eth1 entered promiscuous mode
[   35.310000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   35.320000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   36.520000] cfg80211: Calling CRDA for country: PL
[   36.520000] cfg80211: Regulatory domain changed to country: PL
[   36.530000] cfg80211:  DFS Master region: ETSI
[   36.530000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   36.540000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   36.550000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   36.560000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
[   36.570000] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
[   36.580000] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   36.920000] eth1: link up (1000Mbps/Full duplex)
[   36.920000] br-lan: port 1(eth1) entered forwarding state
[   36.930000] br-lan: port 1(eth1) entered forwarding state
[   36.930000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   36.960000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   38.930000] br-lan: port 1(eth1) entered forwarding state
[   39.360000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   39.390000] device wlan0 entered promiscuous mode
[   39.390000] br-lan: port 2(wlan0) entered forwarding state
[   39.390000] br-lan: port 2(wlan0) entered forwarding state
[   39.660000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   41.390000] br-lan: port 2(wlan0) entered forwarding state
[  403.230000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  403.290000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

16 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

Sat Mar 28 08:57:39 2015 kern.notice kernel: [    7.270000] SCSI subsystem initialized
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.290000] ehci-platform: EHCI generic platform driver
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.300000] ehci-platform ehci-platform: EHCI Host Controller
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.300000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.310000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.340000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.340000] hub 1-0:1.0: USB hub found
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.340000] hub 1-0:1.0: 1 port detected
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.350000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.360000] usbcore: registered new interface driver usb-storage
Sat Mar 28 08:57:39 2015 kern.info kernel: [    7.890000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sat Mar 28 08:57:39 2015 kern.info kernel: [    8.340000] usb-storage 1-1:1.0: USB Mass Storage device detected
Sat Mar 28 08:57:39 2015 kern.info kernel: [    8.350000] scsi0 : usb-storage 1-1:1.0
Sat Mar 28 08:57:39 2015 kern.notice kernel: [    9.350000] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Sat Mar 28 08:57:39 2015 kern.notice kernel: [    9.360000] scsi 0:0:0:1: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Sat Mar 28 08:57:39 2015 kern.notice kernel: [    9.370000] sd 0:0:0:1: [sda] Attached SCSI removable disk
Sat Mar 28 08:57:39 2015 kern.info kernel: [   11.090000] eth1: link up (1000Mbps/Full duplex)
Sat Mar 28 08:57:39 2015 kern.notice kernel: [   13.270000] jffs2: notice: (377) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 52 of xref (0 dead, 28 orphan) found.
Sat Mar 28 08:57:39 2015 user.info kernel: [   13.290000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Sat Mar 28 08:57:39 2015 user.err kernel: [   13.290000] block: unable to load configuration (fstab: Entry not found)
Sat Mar 28 08:57:39 2015 user.info kernel: [   13.300000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
Sat Mar 28 08:57:39 2015 user.info kernel: [   13.320000] block: extroot: not configured
Sat Mar 28 08:57:39 2015 kern.notice kernel: [   13.360000] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 1 orphan) and 52 of xref (0 dead, 28 orphan) found.
Sat Mar 28 08:57:39 2015 user.info kernel: [   13.610000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Sat Mar 28 08:57:39 2015 user.err kernel: [   13.610000] block: unable to load configuration (fstab: Entry not found)
Sat Mar 28 08:57:39 2015 user.info kernel: [   13.620000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
Sat Mar 28 08:57:39 2015 user.info kernel: [   13.630000] block: extroot: not configured
Sat Mar 28 08:57:39 2015 kern.info kernel: [   13.660000] eth1: link down
Sat Mar 28 08:57:39 2015 kern.info kernel: [   18.310000] NET: Registered protocol family 10
Sat Mar 28 08:57:39 2015 kern.info kernel: [   18.350000] l2tp_core: L2TP core driver, V2.0
Sat Mar 28 08:57:39 2015 kern.info kernel: [   18.360000] l2tp_netlink: L2TP netlink interface
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.370000] gre: GRE over IPv4 demultiplexor driver
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.390000] ip_gre: GRE over IPv4 tunneling driver
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.410000] nf_conntrack version 0.5.0 (450 buckets, 1800 max)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.430000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.470000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.470000] Backport generated by backports.git backports-20140320-37-g5c33da0
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.520000] cfg80211: Calling CRDA to update world regulatory domain
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.520000] cfg80211: World regulatory domain updated:
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.530000] cfg80211:  DFS Master region: unset
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.530000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.540000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.550000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.560000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.570000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.570000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.580000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.590000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.600000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.720000] u32 classifier
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.720000]     input device check on
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.720000]     Actions configured
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.730000] Mirror/redirect action on
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.750000] fuse init (API version 7.22)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.820000] usbcore: registered new interface driver cdc_acm
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.820000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.840000] usbcore: registered new interface driver cdc_wdm
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.860000] ip_tables: (C) 2000-2006 Netfilter Core Team
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.920000] usbcore: registered new interface driver usblp
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.960000] usbcore: registered new interface driver usbserial
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.970000] usbcore: registered new interface driver usbserial_generic
Sat Mar 28 08:57:40 2015 kern.info kernel: [   18.990000] usbserial: USB Serial support registered for generic
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.070000] xt_time: kernel timezone is -0000
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.090000] usbcore: registered new interface driver cdc_ether
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.110000] usbcore: registered new interface driver cdc_ncm
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.130000] usbcore: registered new interface driver huawei_cdc_ncm
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.170000] PPP generic driver version 2.4.2
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.170000] PPP MPPE Compression module registered
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.190000] NET: Registered protocol family 24
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.190000] PPTP driver version 0.8.5
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.210000] usbcore: registered new interface driver qmi_wwan
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.230000] usbcore: registered new interface driver rndis_host
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.230000] usbcore: registered new interface driver sierra
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.250000] usbserial: USB Serial support registered for Sierra USB modem
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.250000] usbcore: registered new interface driver sierra_net
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.290000] ath: EEPROM regdomain: 0x0
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.290000] ath: EEPROM indicates default country code should be used
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.290000] ath: doing EEPROM country->regdmn map search
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.290000] ath: country maps to regdmn code: 0x3a
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.290000] ath: Country alpha2 being used: US
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.290000] ath: Regpair used: 0x3a
Sat Mar 28 08:57:40 2015 kern.debug kernel: [   19.310000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.310000] cfg80211: Calling CRDA for country: US
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.320000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.330000] cfg80211: Regulatory domain changed to country: US
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.330000] cfg80211:  DFS Master region: FCC
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.340000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.340000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.350000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.360000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.370000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.380000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.390000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.410000] usbcore: registered new interface driver option
Sat Mar 28 08:57:40 2015 kern.info kernel: [   19.410000] usbserial: USB Serial support registered for GSM modem (1-port)
Sat Mar 28 08:57:43 2015 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Sat Mar 28 08:57:43 2015 kern.info kernel: [   25.220000] usb 1-1: USB disconnect, device number 2
Sat Mar 28 08:57:43 2015 user.err syslog: /dev/mtdblock3 is already mounted
Sat Mar 28 08:57:43 2015 user.emerg syslog: block: /dev/mtdblock3 is already mounted
Sat Mar 28 08:57:43 2015 kern.info kernel: [   25.800000] usb 1-1: new high-speed USB device number 3 using ehci-platform
Sat Mar 28 08:57:44 2015 kern.info kernel: [   25.960000] cdc_ether 1-1:1.0 eth2: register 'cdc_ether' at usb-ehci-platform-1, CDC Ethernet Device, 0c:5b:8f:27:9a:64
Sat Mar 28 08:57:44 2015 kern.info kernel: [   26.070000] usb-storage 1-1:1.2: USB Mass Storage device detected
Sat Mar 28 08:57:44 2015 kern.info kernel: [   26.070000] scsi1 : usb-storage 1-1:1.2
Sat Mar 28 08:57:45 2015 kern.notice kernel: [   27.480000] scsi 1:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Sat Mar 28 08:57:45 2015 kern.notice kernel: [   27.550000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Sat Mar 28 08:57:46 2015 authpriv.info dropbear[1269]: Not backgrounding
Sat Mar 28 08:57:47 2015 user.err syslog: Unkown action change
Sat Mar 28 08:57:47 2015 user.err syslog: Unkown action change
Sat Mar 28 08:57:49 2015 user.err syslog: module is already loaded - xt_multiport
Sat Mar 28 08:57:49 2015 user.err syslog: module is already loaded - xt_comment
Sat Mar 28 08:57:49 2015 user.err syslog: module is already loaded - xt_length
Sat Mar 28 08:57:51 2015 user.err syslog: module is already loaded - xt_multiport
Sat Mar 28 08:57:51 2015 user.err syslog: module is already loaded - xt_comment
Sat Mar 28 08:57:51 2015 user.err syslog: module is already loaded - xt_length
Sat Mar 28 08:57:53 2015 kern.info kernel: [   35.290000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Sat Mar 28 08:57:53 2015 kern.info kernel: [   35.290000] device eth1 entered promiscuous mode
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'lan' is enabled
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'lan' is setting up now
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'lan' is now up
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'loopback' is enabled
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'loopback' is setting up now
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'loopback' is now up
Sat Mar 28 08:57:53 2015 kern.info kernel: [   35.310000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Sat Mar 28 08:57:53 2015 kern.info kernel: [   35.320000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'wan' is enabled
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Network device 'lo' link is up
Sat Mar 28 08:57:53 2015 daemon.notice netifd: Interface 'loopback' has link connectivity
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.520000] cfg80211: Calling CRDA for country: PL
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.520000] cfg80211: Regulatory domain changed to country: PL
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.530000] cfg80211:  DFS Master region: ETSI
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.530000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.540000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.550000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.560000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.570000] cfg80211:   (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
Sat Mar 28 08:57:54 2015 kern.info kernel: [   36.580000] cfg80211:   (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Sat Mar 28 08:57:55 2015 kern.info kernel: [   36.920000] eth1: link up (1000Mbps/Full duplex)
Sat Mar 28 08:57:55 2015 kern.info kernel: [   36.920000] br-lan: port 1(eth1) entered forwarding state
Sat Mar 28 08:57:55 2015 kern.info kernel: [   36.930000] br-lan: port 1(eth1) entered forwarding state
Sat Mar 28 08:57:55 2015 kern.info kernel: [   36.930000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Sat Mar 28 08:57:55 2015 daemon.notice netifd: Network device 'eth1' link is up
Sat Mar 28 08:57:55 2015 daemon.notice netifd: Bridge 'br-lan' link is up
Sat Mar 28 08:57:55 2015 daemon.notice netifd: Interface 'lan' has link connectivity
Sat Mar 28 08:57:55 2015 kern.info kernel: [   36.960000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sat Mar 28 08:57:55 2015 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Sat Mar 28 08:57:57 2015 kern.info kernel: [   38.930000] br-lan: port 1(eth1) entered forwarding state
Sat Mar 28 08:57:57 2015 daemon.crit xl2tpd[1728]: setsockopt recvref[30]: Protocol not available
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1728]: Using l2tp kernel support.
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1741]: xl2tpd version xl2tpd-1.3.6 started on OpenWrt PID:1741
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1741]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc.
Sat Mar 28 08:57:57 2015 kern.info kernel: [   39.360000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1741]: Forked by Scott Balmos and David Stipp, (C) 2001
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1741]: Inherited by Jeff McAdams, (C) 2002
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1741]: Forked again by Xelerance (www.xelerance.com) (C) 2006
Sat Mar 28 08:57:57 2015 daemon.info xl2tpd[1741]: Listening on IP address 0.0.0.0, port 1701
Sat Mar 28 08:57:57 2015 kern.info kernel: [   39.390000] device wlan0 entered promiscuous mode
Sat Mar 28 08:57:57 2015 kern.info kernel: [   39.390000] br-lan: port 2(wlan0) entered forwarding state
Sat Mar 28 08:57:57 2015 kern.info kernel: [   39.390000] br-lan: port 2(wlan0) entered forwarding state
Sat Mar 28 08:57:57 2015 kern.info kernel: [   39.660000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Sat Mar 28 08:57:58 2015 daemon.notice netifd: Network device 'wlan0' link is up
Sat Mar 28 08:57:59 2015 kern.info kernel: [   41.390000] br-lan: port 2(wlan0) entered forwarding state
Sat Mar 28 08:57:59 2015 user.emerg syslog: - init complete -
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq[1832]: started, version 2.71 cachesize 150
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq[1832]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq-dhcp[1832]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq[1832]: using local addresses only for domain lan
Sat Mar 28 08:58:03 2015 daemon.warn dnsmasq[1832]: no servers found in /tmp/resolv.conf.auto, will retry
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq[1832]: read /etc/hosts - 1 addresses
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq[1832]: read /tmp/hosts/dhcp - 1 addresses
Sat Mar 28 08:58:03 2015 daemon.info dnsmasq-dhcp[1832]: read /etc/ethers - 0 addresses
Sat Mar 28 08:58:05 2015 user.notice upnp daemon: external interface not found, not starting
Sat Mar 28 08:58:06 2015 daemon.info dnsmasq-dhcp[1832]: DHCPREQUEST(br-lan) 192.168.1.122 bc:5f:f4:48:81:02
Sat Mar 28 08:58:06 2015 daemon.info dnsmasq-dhcp[1832]: DHCPACK(br-lan) 192.168.1.122 bc:5f:f4:48:81:02 ANdrzej
Sat Mar 28 09:04:01 2015 daemon.notice netifd: Interface 'wan' is disabled
Sat Mar 28 09:04:01 2015 kern.info kernel: [  403.230000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sat Mar 28 09:04:01 2015 daemon.notice netifd: Interface 'wan' is enabled
Sat Mar 28 09:04:01 2015 daemon.notice netifd: Interface 'wan' is disabled
Sat Mar 28 09:04:01 2015 daemon.notice netifd: Interface 'wan' is enabled
Sat Mar 28 09:04:01 2015 kern.info kernel: [  403.290000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

17 Odpowiedź przez pepe2k

  • pepe2k
  • pepe2k
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2012-10-29
  • Posty: 5,028

Odp: TP LINK WR710N i LUCI

Daj jeszcze więcej i czasem nie korzystaj z dedykowanych tagów BBCode! Niech będzie jeszcze mniej czytelne!

18 Odpowiedź przez Kristof2014

  • Zarejestrowany: 2014-04-22
  • Posty: 44

Odp: TP LINK WR710N i LUCI

W dziale do pobrania obrazy Luci nie są aktualne????

19 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

http://images69.fotosik.pl/821/74c6274e9dc0a837m.jpg


http://images70.fotosik.pl/821/f5f9b5324179f9c9m.jpg


http://images67.fotosik.pl/822/c829ff3c42d90942m.jpg


http://images67.fotosik.pl/822/c829ff3c42d90942m.jpg

20 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

Kristof2014 napisał/a:

W dziale do pobrania obrazy Luci nie są aktualne????

Są aktualne.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

21 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,014

Odp: TP LINK WR710N i LUCI

@mrrowek: zaklikaj sobei eth2 tak jak mówiłem jak chcesz przez hilinka.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

22 Odpowiedź przez mrox

  • mrox
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2010-06-17
  • Posty: 207

Odp: TP LINK WR710N i LUCI

@mrrowek: Gdzie kupiłeś V1.2? W większości dużych sklepów są już tylko V2.0.

23 Odpowiedź przez mrrowek (edytowany przez mrrowek 2015-04-22 16:31:32)

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

thx działa
w neonecie jest/była wyprzedaż

24 Odpowiedź przez simono (edytowany przez simono 2015-04-23 07:10:35)

  • simono
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2013-08-10
  • Posty: 596

Odp: TP LINK WR710N i LUCI

I po ile była/jest ta wyprzedaż w Neonet?
Edit: znalazłem na stronie 89,99
Inna sprawa to jaki to zasięg oferuje, znaczy się do jakiej odległości od routera maks prędkość?

25 Odpowiedź przez mrrowek

  • Zarejestrowany: 2014-10-09
  • Posty: 186

Odp: TP LINK WR710N i LUCI

w domu jednorodzinnym na poziomie piętra jest ok trochę gorzej na parterze bo inny poziom ,.