Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → extrot bbluci
Zaloguj się lub zarejestruj by napisać odpowiedź
witam czemu po zrobieniu extrota z poziomu luci w etc/config/fstab :pojawia się coś takiego config global
option anon_swap '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
option anon_mount '1'
config swap
option enabled '0'
config mount
option device '/dev/sda'
option fstype 'ext4'
option is_rootfs '1'
option enabled '1'
a powinny być inne wpisy i nie zwiększa się ilość miejsca na pakiety
Bo luci jest zwalone i nie przepisane pod nowe konfigi BB.
a z konsoli się da co trzeba doinstalować
http://eko.one.pl/?p=openwrt-externalro … ierbreaker
ok poszło tylko mam jeszcze jedno pytanie jaki sterownik do kamerki ps 3 sleh 00448 czytałem ten poradnik OpenWrt - Webcam ale nic
Jeżeli od ps3 to kmod-video-gspca-ov534
instalowałem sterowniki i po woisaniu wychodzi coś takigo
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.49 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #4 Fri Mar 13 18:34:17 CET 2015
[ 0.000000] SoC: VR9 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is TDW8970 - TP-LINK TD-W8970
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 80424b80, node_mem_map 810036a0
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00014380
[ 0.000000] Readback ErrCtl register=00014380
[ 0.000000] Memory: 60072k/65536k available (3217k kernel code, 5464k reserved, 1136k data, 244k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] Setting up vectored interrupts
[ 0.000000] CPU Clock: 500MHz
[ 0.028000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.040000] pinctrl core: initialized pinctrl subsystem
[ 0.044000] NET: Registered protocol family 16
[ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.188000] ath9k,eeprom ath9k_eep.8: failed to load eeprom address
[ 0.204000] bio: create slab <bio-0> at 0
[ 0.208000] usbcore: registered new interface driver usbfs
[ 0.212000] usbcore: registered new interface driver hub
[ 0.216000] usbcore: registered new device driver usb
[ 0.220000] PCI host bridge to bus 0000:00
[ 0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.228000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.236000] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060000
[ 0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.248000] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.248000] pci 0000:01:00.0: [168c:abcd] type 00 class 0x020000
[ 0.248000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.248000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.248000] pci 0000:01:00.0: supports D1
[ 0.248000] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.248000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.248000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.248000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[ 0.252000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref]
[ 0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit]
[ 0.260000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref]
[ 0.264000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.268000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff]
[ 0.272000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref]
[ 0.276000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.280000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[ 0.284000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[ 0.288000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 0.292000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[ 0.296000] Switching to clocksource MIPS
[ 0.304000] NET: Registered protocol family 2
[ 0.308000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.316000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.320000] TCP: Hash tables configured (established 512 bind 512)
[ 0.328000] TCP: reno registered
[ 0.332000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.336000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.344000] NET: Registered protocol family 1
[ 0.348000] PCI: CLS 0 bytes, default 32
[ 0.348000] gptu: totally 6 16-bit timers/counters
[ 0.352000] gptu: misc_register on minor 63
[ 0.356000] gptu: succeeded to request irq 126
[ 0.360000] gptu: succeeded to request irq 127
[ 0.364000] gptu: succeeded to request irq 128
[ 0.372000] gptu: succeeded to request irq 129
[ 0.376000] gptu: succeeded to request irq 130
[ 0.380000] gptu: succeeded to request irq 131
[ 0.388000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a2x.bin
[ 0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000
[ 0.400000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000
[ 0.508000] Wired TLB entries for Linux read_c0_wired() = 0
[ 0.516000] config3 0x2424 MT 1
[ 0.516000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[ 0.516000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[ 0.532000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.536000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.548000] msgmni has been set to 117
[ 0.552000] io scheduler noop registered
[ 0.556000] io scheduler deadline registered (default)
[ 0.564000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 0.568000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.588000] spi_gpio spi.7: master is unqueued, this is deprecated
[ 0.592000] m25p80 spi32766.0: found s25fl064k, expected en25q64
[ 0.596000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
[ 0.604000] 5 ofpart partitions found on MTD device spi32766.0
[ 0.608000] Creating 5 MTD partitions on "spi32766.0":
[ 0.612000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.620000] 0x000000020000-0x0000006c0000 : "firmware"
[ 0.628000] 0x000000195ff4-0x0000006c0000 : "rootfs"
[ 0.632000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.644000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.652000] mtd: partition "rootfs_data" created automatically, ofs=0x5c0000, len=0x100000
[ 0.656000] 0x0000005c0000-0x0000006c0000 : "rootfs_data"
[ 1.680000] 0x0000006c0000-0x0000007c0000 : "dsl_fw"
[ 1.688000] 0x0000007c0000-0x0000007d0000 : "config"
[ 1.692000] 0x0000007d0000-0x000000800000 : "boardconfig"
[ 1.804000] libphy: lantiq,xrx200-mdio: probed
[ 1.812000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[ 1.820000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[ 1.828000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[ 1.836000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[ 1.844000] wdt 1f8803f0.watchdog: Init done
[ 1.848000] leds-gpio gpio-leds.10: pins are not configured from the driver
[ 1.856000] TCP: cubic registered
[ 1.860000] NET: Registered protocol family 17
[ 1.864000] Bridge firewalling registered
[ 1.868000] 8021q: 802.1Q VLAN Support v1.8
[ 1.952000] ath9k,eeprom ath9k_eep.8: using led pin 0.
[ 1.956000] ath9k,eeprom ath9k_eep.8: loaded ath9k eeprom
[ 1.964000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.972000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 2.084000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.088000] Freeing unused kernel memory: 244K (80443000 - 80480000)
[ 2.828000] eth0: port 0 got link
[ 3.840000] eth0: port 2 got link
[ 4.860000] eth0: port 4 got link
[ 45.680000] SCSI subsystem initialized
[ 45.688000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 45.696000] ehci-platform: EHCI generic platform driver
[ 45.704000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 45.708000] Chip Version :000c BurstSize=4
[ 46.312000] IFXUSB: USB core #0 soft-reset
[ 46.612000] IFXUSB: USB core #0 soft-reset
[ 46.616000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 46.620000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 46.628000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 46.636000] IFXUSB: Init: Power Port (0)
[ 46.640000] hub 1-0:1.0: USB hub found
[ 46.644000] hub 1-0:1.0: 1 port detected
[ 47.148000] IFXUSB: USB core #1 soft-reset
[ 47.452000] IFXUSB: USB core #1 soft-reset
[ 47.452000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 47.460000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[ 47.464000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[ 47.472000] IFXUSB: Init: Power Port (0)
[ 47.476000] hub 2-0:1.0: USB hub found
[ 47.480000] hub 2-0:1.0: 1 port detected
[ 47.484000] ifxusb_hcd ifxusb_hcd: requested GPIO 233
[ 47.492000] usbcore: registered new interface driver usb-storage
[ 47.840000] usb 1-1: new high-speed USB device number 2 using ifxusb_hcd
[ 48.176000] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 48.184000] scsi0 : usb-storage 1-1:1.0
[ 48.532000] usb 2-1: new high-speed USB device number 2 using ifxusb_hcd
[ 49.264000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 49.284000] sd 0:0:0:0: [sda] 1952768 512-byte logical blocks: (999 MB/953 MiB)
[ 49.332000] sd 0:0:0:0: [sda] Write Protect is off
[ 49.336000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 49.372000] sd 0:0:0:0: [sda] No Caching mode page found
[ 49.376000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 49.584000] sd 0:0:0:0: [sda] No Caching mode page found
[ 49.588000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 49.732000] sda: sda1 < sda5 >
[ 49.852000] sd 0:0:0:0: [sda] No Caching mode page found
[ 49.856000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 49.860000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 66.328000] jffs2: notice: (342) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (0 unchecked, 3 orphan) and 90 of xref (0 dead, 71 orphan) found.
[ 66.364000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 66.368000] block: unable to load configuration (fstab: Entry not found)
[ 66.376000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 66.572000] EXT4-fs (sda5): mounting ext3 file system using the ext4 subsystem
[ 66.812000] EXT4-fs (sda5): recovery complete
[ 66.852000] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts:
[ 67.968000] eth0: port 0 lost link
[ 67.968000] eth0: port 2 lost link
[ 67.984000] eth0: port 4 lost link
[ 77.344000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 77.344000]
[ 77.372000] NET: Registered protocol family 10
[ 77.388000] NET: Registered protocol family 8
[ 77.388000] NET: Registered protocol family 20
[ 77.412000] l2tp_core: L2TP core driver, V2.0
[ 77.416000] l2tp_netlink: L2TP netlink interface
[ 77.436000] gre: GRE over IPv4 demultiplexor driver
[ 77.444000] ip_gre: GRE over IPv4 tunneling driver
[ 77.464000] PPP generic driver version 2.4.2
[ 77.484000] nf_conntrack version 0.5.0 (942 buckets, 3768 max)
[ 77.496000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 77.556000] MEI CPE Driver, Version 1.2.0
[ 77.556000]
[ 77.556000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
[ 77.564000]
[ 77.564000]
[ 77.564000] Lantiq CPE API Driver version: DSL CPE API V4.11.4
[ 77.588000]
[ 77.588000] Predefined debug level: 2
[ 77.620000] u32 classifier
[ 77.624000] input device check on
[ 77.628000] Actions configured
[ 77.636000] Mirror/redirect action on
[ 77.664000] fuse init (API version 7.22)
[ 77.704000] usbcore: registered new interface driver cdc_acm
[ 77.708000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 77.724000] usbcore: registered new interface driver cdc_wdm
[ 77.732000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 77.740000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 77.756000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 77.788000] Infineon Technologies DEU driver version 2.0.0
[ 77.796000] IFX DEU DES initialized (multiblock).
[ 77.812000] IFX DEU AES initialized (multiblock).
[ 77.816000] IFX DEU ARC4 initialized (multiblock).
[ 77.828000] IFX DEU SHA1 initialized.
[ 77.828000] IFX DEU MD5 initialized.
[ 77.840000] IFX DEU SHA1_HMAC initialized.
[ 77.840000] IFX DEU MD5_HMAC initialized.
[ 77.884000] PPP MPPE Compression module registered
[ 77.892000] NET: Registered protocol family 24
[ 77.900000] PPTP driver version 0.8.5
[ 77.916000] usbcore: registered new interface driver usblp
[ 77.936000] usbcore: registered new interface driver usbserial
[ 77.952000] usbcore: registered new interface driver usbserial_generic
[ 77.968000] usbserial: USB Serial support registered for generic
[ 78.036000] xt_time: kernel timezone is -0000
[ 78.044000] usbcore: registered new interface driver cdc_ether
[ 78.052000] usbcore: registered new interface driver cdc_ncm
[ 78.092000] cfg80211: Calling CRDA to update world regulatory domain
[ 78.100000] cfg80211: World regulatory domain updated:
[ 78.104000] cfg80211: DFS Master region: unset
[ 78.108000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 78.116000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.124000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.132000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.140000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.148000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 78.156000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 78.164000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.172000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 78.180000] usbcore: registered new interface driver huawei_cdc_ncm
[ 78.204000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 78.280000] usbcore: registered new interface driver qmi_wwan
[ 78.288000] usbcore: registered new interface driver rndis_host
[ 78.296000] usbcore: registered new interface driver sierra
[ 78.300000] usbserial: USB Serial support registered for Sierra USB modem
[ 78.312000] usbcore: registered new interface driver sierra_net
[ 78.360000] usbcore: registered new interface driver option
[ 78.364000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 78.388000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 78.396000] ath: EEPROM regdomain: 0x0
[ 78.396000] ath: EEPROM indicates default country code should be used
[ 78.396000] ath: doing EEPROM country->regdmn map search
[ 78.396000] ath: country maps to regdmn code: 0x3a
[ 78.396000] ath: Country alpha2 being used: US
[ 78.396000] ath: Regpair used: 0x3a
[ 78.408000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 78.420000] cfg80211: Calling CRDA for country: US
[ 78.424000] cfg80211: Regulatory domain changed to country: US
[ 78.428000] cfg80211: DFS Master region: FCC
[ 78.432000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 78.444000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 78.452000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 78.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 78.468000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 78.476000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 78.484000] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xbc000000, irq=144
[ 95.308000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 95.332000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 95.336000] eth0: port 0 got link
[ 95.344000] eth0: port 2 got link
[ 95.344000] eth0: port 4 got link
[ 95.348000] device eth0.1 entered promiscuous mode
[ 95.352000] device eth0 entered promiscuous mode
[ 95.368000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 95.376000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 95.384000] br-lan: port 1(eth0.1) entered forwarding state
[ 95.388000] br-lan: port 1(eth0.1) entered forwarding state
[ 95.392000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 95.428000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 96.356000] br-lan: port 1(eth0.1) entered disabled state
[ 97.376000] br-lan: port 1(eth0.1) entered forwarding state
[ 97.380000] br-lan: port 1(eth0.1) entered forwarding state
[ 99.384000] br-lan: port 1(eth0.1) entered forwarding state
[ 114.400000] ATM1.0.26 ATM (A1) firmware version 0.24
[ 114.404000] ifxmips_atm: ATM init succeed
[ 133.892000] eth0: port 2 lost link
[ 135.904000] eth0: port 2 got link
[ 225.180000] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0x82130000
[ 225.192000] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0x82130000
[ 228.212000] leave showtime
[ 260.688000] enter showtime, cell rate: 0 - 2669, 1 - 2669, xdata addr: 0x82130000
[ 260.708000] enter showtime, cell rate: 0 - 2669, 1 - 2669, xdata addr: 0x82130000
[ 671.184000] videodev: Unknown symbol i2c_unregister_device (err 0)
[ 671.200000] v4l2_common: Unknown symbol i2c_new_device (err 0)
[ 671.204000] v4l2_common: Unknown symbol v4l2_subdev_init (err 0)
[ 671.212000] v4l2_common: Unknown symbol v4l2_device_register_subdev (err 0)
[ 671.220000] v4l2_common: Unknown symbol i2c_unregister_device (err 0)
[ 671.224000] v4l2_common: Unknown symbol v4l2_ctrl_get_menu (err 0)
[ 671.232000] v4l2_common: Unknown symbol i2c_new_probed_device (err 0)
[ 671.236000] v4l2_common: Unknown symbol v4l2_ctrl_fill (err 0)
root@OpenWrt:~#
Zrestartuj go żeby się wszystko załadowało we właściwej kolejności.
poszło tylko http://192.168.1.1:8080/?action=stream nie może być wyświetlony ponieważ zawiera błędy tylko jakie a w konfig jest tak
config mjpg-streamer 'core'
option input 'uvc'
option output 'http'
option device '/dev/video0'
option resolution '640x480'
option fps '5'
option www '/www/webcam'
option port '8080'
option username 'openwrt'
option password 'openwrt'
option enabled '1'
Nie patrz w konfig tylko w źródło strony. Czasami nie przez IE próbujesz to oglądać? yuyv włącz także.
yuyv oświeć mnie co to jest przez mozille przez explorer nie idzie ale na 1043 twojego gargolca nie ma żadnego problemu
Opcja w gui od kamery.
ale ja zainstalowałem z konsoli i nie mam gui [luci] kamery jeżeli o to chodzi
coś z kamerką ale spróbuje na tej vf0520 tylko jaki kmod-video-gspca
W poradniku po vid/pid zobacz
prosze jeszcze raz o pomoc co jest nie tak że kamerka nie działa mam creatiwa vf 0520 a oto podgląd
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.49 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #4 Fri Mar 13 18:34:17 CET 2015
[ 0.000000] SoC: VR9 rev 1.2
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019556 (MIPS 34Kc)
[ 0.000000] MIPS: machine is TDW8970 - TP-LINK TD-W8970
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 80424b80, node_mem_map 810036a0
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0005438d
[ 0.000000] Readback ErrCtl register=0005438d
[ 0.000000] Memory: 60072k/65536k available (3217k kernel code, 5464k reserved, 1136k data, 244k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] Setting up vectored interrupts
[ 0.000000] CPU Clock: 500MHz
[ 0.028000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 512
[ 0.040000] pinctrl core: initialized pinctrl subsystem
[ 0.044000] NET: Registered protocol family 16
[ 0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[ 0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[ 0.188000] ath9k,eeprom ath9k_eep.8: failed to load eeprom address
[ 0.204000] bio: create slab <bio-0> at 0
[ 0.208000] usbcore: registered new interface driver usbfs
[ 0.212000] usbcore: registered new interface driver hub
[ 0.216000] usbcore: registered new device driver usb
[ 0.220000] PCI host bridge to bus 0000:00
[ 0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.228000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.236000] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060000
[ 0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.248000] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.248000] pci 0000:01:00.0: [168c:abcd] type 00 class 0x020000
[ 0.248000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.248000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.248000] pci 0000:01:00.0: supports D1
[ 0.248000] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.248000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.248000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.248000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[ 0.252000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref]
[ 0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit]
[ 0.260000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref]
[ 0.264000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.268000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff]
[ 0.272000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref]
[ 0.276000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.280000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[ 0.284000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[ 0.288000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 0.292000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[ 0.296000] Switching to clocksource MIPS
[ 0.304000] NET: Registered protocol family 2
[ 0.308000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.316000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.320000] TCP: Hash tables configured (established 512 bind 512)
[ 0.328000] TCP: reno registered
[ 0.332000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.336000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.344000] NET: Registered protocol family 1
[ 0.348000] PCI: CLS 0 bytes, default 32
[ 0.348000] gptu: totally 6 16-bit timers/counters
[ 0.352000] gptu: misc_register on minor 63
[ 0.356000] gptu: succeeded to request irq 126
[ 0.360000] gptu: succeeded to request irq 127
[ 0.364000] gptu: succeeded to request irq 128
[ 0.372000] gptu: succeeded to request irq 129
[ 0.376000] gptu: succeeded to request irq 130
[ 0.380000] gptu: succeeded to request irq 131
[ 0.388000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a2x.bin
[ 0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000
[ 0.400000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000
[ 0.508000] Wired TLB entries for Linux read_c0_wired() = 0
[ 0.516000] config3 0x2424 MT 1
[ 0.516000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[ 0.516000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[ 0.532000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.536000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.548000] msgmni has been set to 117
[ 0.552000] io scheduler noop registered
[ 0.556000] io scheduler deadline registered (default)
[ 0.564000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 0.568000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.588000] spi_gpio spi.7: master is unqueued, this is deprecated
[ 0.592000] m25p80 spi32766.0: found s25fl064k, expected en25q64
[ 0.596000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
[ 0.604000] 5 ofpart partitions found on MTD device spi32766.0
[ 0.608000] Creating 5 MTD partitions on "spi32766.0":
[ 0.612000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.620000] 0x000000020000-0x0000006c0000 : "firmware"
[ 0.628000] 0x000000195ff4-0x0000006c0000 : "rootfs"
[ 0.632000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.644000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.652000] mtd: partition "rootfs_data" created automatically, ofs=0x5c0000, len=0x100000
[ 0.656000] 0x0000005c0000-0x0000006c0000 : "rootfs_data"
[ 1.680000] 0x0000006c0000-0x0000007c0000 : "dsl_fw"
[ 1.688000] 0x0000007c0000-0x0000007d0000 : "config"
[ 1.692000] 0x0000007d0000-0x000000800000 : "boardconfig"
[ 1.804000] libphy: lantiq,xrx200-mdio: probed
[ 1.812000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[ 1.820000] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[ 1.828000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[ 1.836000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[ 1.844000] wdt 1f8803f0.watchdog: Init done
[ 1.848000] leds-gpio gpio-leds.10: pins are not configured from the driver
[ 1.856000] TCP: cubic registered
[ 1.860000] NET: Registered protocol family 17
[ 1.864000] Bridge firewalling registered
[ 1.868000] 8021q: 802.1Q VLAN Support v1.8
[ 1.952000] ath9k,eeprom ath9k_eep.8: using led pin 0.
[ 1.956000] ath9k,eeprom ath9k_eep.8: loaded ath9k eeprom
[ 1.964000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.972000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 2.084000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.088000] Freeing unused kernel memory: 244K (80443000 - 80480000)
[ 2.828000] eth0: port 0 got link
[ 2.828000] eth0: port 5 got link
[ 4.872000] eth0: port 4 got link
[ 5.848000] eth0: port 2 got link
[ 45.680000] SCSI subsystem initialized
[ 45.688000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 45.696000] ehci-platform: EHCI generic platform driver
[ 45.704000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[ 45.708000] Chip Version :000c BurstSize=4
[ 46.312000] IFXUSB: USB core #0 soft-reset
[ 46.616000] IFXUSB: USB core #0 soft-reset
[ 46.616000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 46.620000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[ 46.628000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[ 46.636000] IFXUSB: Init: Power Port (0)
[ 46.640000] hub 1-0:1.0: USB hub found
[ 46.644000] hub 1-0:1.0: 1 port detected
[ 47.148000] IFXUSB: USB core #1 soft-reset
[ 47.452000] IFXUSB: USB core #1 soft-reset
[ 47.452000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[ 47.460000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
[ 47.464000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[ 47.472000] IFXUSB: Init: Power Port (0)
[ 47.476000] hub 2-0:1.0: USB hub found
[ 47.480000] hub 2-0:1.0: 1 port detected
[ 47.484000] ifxusb_hcd ifxusb_hcd: requested GPIO 233
[ 47.492000] usbcore: registered new interface driver usb-storage
[ 47.852000] usb 1-1: new high-speed USB device number 2 using ifxusb_hcd
[ 48.212000] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 48.216000] scsi0 : usb-storage 1-1:1.0
[ 48.568000] usb 2-1: new high-speed USB device number 2 using ifxusb_hcd
[ 49.284000] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 49.360000] sd 0:0:0:0: [sda] 1952768 512-byte logical blocks: (999 MB/953 MiB)
[ 49.404000] sd 0:0:0:0: [sda] Write Protect is off
[ 49.408000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 49.456000] sd 0:0:0:0: [sda] No Caching mode page found
[ 49.460000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 49.684000] sd 0:0:0:0: [sda] No Caching mode page found
[ 49.688000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 49.836000] sda: sda1 < sda5 >
[ 49.848000] sd 0:0:0:0: [sda] No Caching mode page found
[ 49.852000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 49.856000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 66.340000] jffs2: notice: (342) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (0 unchecked, 3 orphan) and 90 of xref (0 dead, 71 orphan) found.
[ 66.372000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 66.380000] block: unable to load configuration (fstab: Entry not found)
[ 66.388000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 66.588000] EXT4-fs (sda5): mounting ext3 file system using the ext4 subsystem
[ 67.216000] EXT4-fs (sda5): recovery complete
[ 67.256000] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts:
[ 67.984000] eth0: port 0 lost link
[ 67.984000] eth0: port 5 lost link
[ 68.000000] eth0: port 2 lost link
[ 68.000000] eth0: port 4 lost link
[ 77.176000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 77.176000]
[ 77.240000] NET: Registered protocol family 10
[ 77.264000] NET: Registered protocol family 8
[ 77.264000] NET: Registered protocol family 20
[ 77.304000] l2tp_core: L2TP core driver, V2.0
[ 77.312000] l2tp_netlink: L2TP netlink interface
[ 77.340000] gre: GRE over IPv4 demultiplexor driver
[ 77.348000] ip_gre: GRE over IPv4 tunneling driver
[ 77.368000] PPP generic driver version 2.4.2
[ 77.392000] nf_conntrack version 0.5.0 (942 buckets, 3768 max)
[ 77.408000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 77.440000] MEI CPE Driver, Version 1.2.0
[ 77.440000]
[ 77.440000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
[ 77.448000]
[ 77.448000]
[ 77.448000] Lantiq CPE API Driver version: DSL CPE API V4.11.4
[ 77.476000]
[ 77.476000] Predefined debug level: 2
[ 77.544000] Linux video capture interface: v2.00
[ 77.576000] u32 classifier
[ 77.576000] input device check on
[ 77.580000] Actions configured
[ 77.592000] Mirror/redirect action on
[ 77.620000] fuse init (API version 7.22)
[ 77.720000] usbcore: registered new interface driver cdc_acm
[ 77.724000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 77.736000] usbcore: registered new interface driver cdc_wdm
[ 77.752000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 77.760000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 77.800000] gspca_main: v2.14.0 registered
[ 77.816000] usbcore: registered new interface driver ov519
[ 77.828000] usbcore: registered new interface driver ov534
[ 77.840000] usbcore: registered new interface driver ov534_9
[ 77.852000] usbcore: registered new interface driver pac207
[ 77.864000] usbcore: registered new interface driver gspca_sn9c20x
[ 77.876000] usbcore: registered new interface driver sonixb
[ 77.888000] usbcore: registered new interface driver sonixj
[ 77.900000] usbcore: registered new interface driver spca500
[ 77.912000] usbcore: registered new interface driver spca501
[ 77.924000] usbcore: registered new interface driver spca505
[ 77.936000] usbcore: registered new interface driver spca506
[ 77.948000] usbcore: registered new interface driver spca508
[ 77.960000] usbcore: registered new interface driver spca561
[ 77.968000] usbcore: registered new interface driver sq905
[ 77.984000] usbcore: registered new interface driver sq905c
[ 77.996000] usbcore: registered new interface driver stk014
[ 78.008000] usbcore: registered new interface driver STV06xx
[ 78.020000] usbcore: registered new interface driver sunplus
[ 78.032000] usbcore: registered new interface driver t613
[ 78.040000] usbcore: registered new interface driver tv8532
[ 78.060000] usbcore: registered new interface driver gspca_zc3xx
[ 78.076000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 78.108000] Infineon Technologies DEU driver version 2.0.0
[ 78.116000] IFX DEU DES initialized (multiblock).
[ 78.128000] IFX DEU AES initialized (multiblock).
[ 78.132000] IFX DEU ARC4 initialized (multiblock).
[ 78.144000] IFX DEU SHA1 initialized.
[ 78.144000] IFX DEU MD5 initialized.
[ 78.152000] IFX DEU SHA1_HMAC initialized.
[ 78.156000] IFX DEU MD5_HMAC initialized.
[ 78.204000] PPP MPPE Compression module registered
[ 78.212000] NET: Registered protocol family 24
[ 78.216000] PPTP driver version 0.8.5
[ 78.236000] usbcore: registered new interface driver usblp
[ 78.260000] usbcore: registered new interface driver usbserial
[ 78.268000] usbcore: registered new interface driver usbserial_generic
[ 78.276000] usbserial: USB Serial support registered for generic
[ 78.376000] xt_time: kernel timezone is -0000
[ 78.396000] usbcore: registered new interface driver cdc_ether
[ 78.420000] usbcore: registered new interface driver cdc_ncm
[ 78.516000] cfg80211: Calling CRDA to update world regulatory domain
[ 78.532000] usbcore: registered new interface driver huawei_cdc_ncm
[ 78.540000] cfg80211: World regulatory domain updated:
[ 78.540000] cfg80211: DFS Master region: unset
[ 78.548000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 78.556000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.564000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.572000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.580000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.588000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 78.596000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 78.604000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 78.612000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 78.628000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 78.728000] usbcore: registered new interface driver qmi_wwan
[ 78.752000] usbcore: registered new interface driver rndis_host
[ 78.760000] usbcore: registered new interface driver sierra
[ 78.768000] usbserial: USB Serial support registered for Sierra USB modem
[ 78.776000] usbcore: registered new interface driver sierra_net
[ 78.956000] usbcore: registered new interface driver option
[ 78.972000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 79.076000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 79.084000] ath: EEPROM regdomain: 0x0
[ 79.084000] ath: EEPROM indicates default country code should be used
[ 79.084000] ath: doing EEPROM country->regdmn map search
[ 79.084000] ath: country maps to regdmn code: 0x3a
[ 79.084000] ath: Country alpha2 being used: US
[ 79.084000] ath: Regpair used: 0x3a
[ 79.096000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 79.100000] cfg80211: Calling CRDA for country: US
[ 79.108000] cfg80211: Regulatory domain changed to country: US
[ 79.112000] cfg80211: DFS Master region: FCC
[ 79.116000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 79.124000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 79.132000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 79.140000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 79.148000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 79.156000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 79.168000] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xbc000000, irq=144
[ 94.024000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 94.036000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 94.040000] device eth0.1 entered promiscuous mode
[ 94.044000] device eth0 entered promiscuous mode
[ 94.056000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 94.312000] eth0: port 0 got link
[ 94.312000] eth0: port 5 got link
[ 94.320000] eth0: port 2 got link
[ 94.320000] eth0: port 4 got link
[ 94.348000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 94.352000] br-lan: port 1(eth0.1) entered forwarding state
[ 94.356000] br-lan: port 1(eth0.1) entered forwarding state
[ 94.364000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 94.376000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 96.360000] br-lan: port 1(eth0.1) entered forwarding state
[ 118.684000] ATM1.0.26 ATM (A1) firmware version 0.24
[ 118.688000] ifxmips_atm: ATM init succeed
[ 136.500000] eth0: port 2 lost link
[ 139.500000] eth0: port 2 got link
[ 165.892000] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0x825d0000
[ 165.904000] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0x825d0000
[ 169.928000] leave showtime
[ 202.336000] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0x825d0000
[ 202.348000] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0x825d0000
[ 422.112000] eth0: tx ring full
[ 427.612000] eth0: tx ring full
[ 428.904000] eth0: tx ring full
[ 429.308000] eth0: tx ring full
[ 435.216000] eth0: tx ring full
[ 436.320000] eth0: tx ring full
[ 438.036000] eth0: tx ring full
[ 440.132000] eth0: tx ring full
[ 440.560000] eth0: tx ring full
[ 441.160000] eth0: tx ring full
[ 443.272000] eth0: tx ring full
[ 448.064000] eth0: tx ring full
[ 456.540000] eth0: tx ring full
[ 458.092000] eth0: tx ring full
[ 466.972000] eth0: tx ring full
[ 476.548000] eth0: tx ring full
[ 483.136000] eth0: tx ring full
[ 483.412000] eth0: tx ring full
[ 483.688000] eth0: tx ring full
[ 484.264000] eth0: tx ring full
[ 484.836000] eth0: tx ring full
[ 484.992000] eth0: tx ring full
[ 485.140000] eth0: tx ring full
[ 485.428000] eth0: tx ring full
[ 485.572000] eth0: tx ring full
[ 486.148000] eth0: tx ring full
[ 486.296000] eth0: tx ring full
[ 486.332000] eth0: tx ring full
[ 486.452000] eth0: tx ring full
[ 486.612000] eth0: tx ring full
[ 487.020000] eth0: tx ring full
[ 487.316000] eth0: tx ring full
[ 487.760000] eth0: tx ring full
[ 487.908000] eth0: tx ring full
[ 488.052000] eth0: tx ring full
[ 488.208000] eth0: tx ring full
[ 488.780000] eth0: tx ring full
[ 488.932000] eth0: tx ring full
[ 489.812000] eth0: tx ring full
[ 489.964000] eth0: tx ring full
[ 490.020000] eth0: tx ring full
[ 490.812000] eth0: tx ring full
[ 490.956000] eth0: tx ring full
[ 491.404000] eth0: tx ring full
[ 491.552000] eth0: tx ring full
[ 491.704000] eth0: tx ring full
[ 492.032000] eth0: tx ring full
[ 492.040000] eth0: tx ring full
[ 492.548000] eth0: tx ring full
[ 492.692000] eth0: tx ring full
[ 492.700000] eth0: tx ring full
[ 493.432000] eth0: tx ring full
[ 493.868000] eth0: tx ring full
[ 494.160000] eth0: tx ring full
[ 494.588000] eth0: tx ring full
[ 494.740000] eth0: tx ring full
[ 495.036000] eth0: tx ring full
[ 495.040000] eth0: tx ring full
[ 495.448000] eth0: tx ring full
[ 495.608000] eth0: tx ring full
[ 496.164000] eth0: tx ring full
[ 497.028000] eth0: tx ring full
[ 498.156000] eth0: tx ring full
[ 498.168000] eth0: tx ring full
[ 498.596000] eth0: tx ring full
[ 498.748000] eth0: tx ring full
[ 499.024000] eth0: tx ring full
[ 499.172000] eth0: tx ring full
[ 499.452000] eth0: tx ring full
[ 499.460000] eth0: tx ring full
[ 499.608000] eth0: tx ring full
[ 500.212000] eth0: tx ring full
[ 500.360000] eth0: tx ring full
[ 500.508000] eth0: tx ring full
[ 500.652000] eth0: tx ring full
[ 500.804000] eth0: tx ring full
[ 500.816000] eth0: tx ring full
[ 501.400000] eth0: tx ring full
[ 502.232000] eth0: tx ring full
[ 502.272000] eth0: tx ring full
[ 502.420000] eth0: tx ring full
[ 502.428000] eth0: tx ring full
[ 502.576000] eth0: tx ring full
[ 502.720000] eth0: tx ring full
[ 503.092000] eth0: tx ring full
[ 503.916000] eth0: tx ring full
[ 505.644000] eth0: tx ring full
[ 507.012000] eth0: tx ring full
[ 507.220000] eth0: tx ring full
[ 507.440000] eth0: tx ring full
[ 507.772000] eth0: tx ring full
[ 507.800000] eth0: tx ring full
[ 508.120000] eth0: tx ring full
[ 508.288000] eth0: tx ring full
[ 512.696000] eth0: tx ring full
[ 512.992000] eth0: tx ring full
[ 513.144000] eth0: tx ring full
[ 513.292000] eth0: tx ring full
[ 513.300000] eth0: tx ring full
[ 514.032000] eth0: tx ring full
[ 514.180000] eth0: tx ring full
[ 514.348000] eth0: tx ring full
[ 514.796000] eth0: tx ring full
[ 514.808000] eth0: tx ring full
[ 515.052000] eth0: tx ring full
[ 515.204000] eth0: tx ring full
[ 515.208000] eth0: tx ring full
[ 518.672000] eth0: tx ring full
[ 518.968000] eth0: tx ring full
[ 519.116000] eth0: tx ring full
[ 519.356000] eth0: tx ring full
[ 519.368000] eth0: tx ring full
[ 519.568000] eth0: tx ring full
[ 519.716000] eth0: tx ring full
[ 519.864000] eth0: tx ring full
[ 520.076000] eth0: tx ring full
[ 520.084000] eth0: tx ring full
[ 520.456000] eth0: tx ring full
[ 520.604000] eth0: tx ring full
[ 520.756000] eth0: tx ring full
[ 520.764000] eth0: tx ring full
[ 520.924000] eth0: tx ring full
[ 520.952000] eth0: tx ring full
[ 521.076000] eth0: tx ring full
[ 521.224000] eth0: tx ring full
[ 521.376000] eth0: tx ring full
[ 521.384000] eth0: tx ring full
[ 521.404000] eth0: tx ring full
[ 521.808000] eth0: tx ring full
[ 521.952000] eth0: tx ring full
[ 522.104000] eth0: tx ring full
[ 522.252000] eth0: tx ring full
[ 523.280000] eth0: tx ring full
[ 523.560000] eth0: tx ring full
[ 523.708000] eth0: tx ring full
[ 523.856000] eth0: tx ring full
[ 524.264000] eth0: tx ring full
[ 524.476000] eth0: tx ring full
[ 525.388000] eth0: tx ring full
[ 526.256000] eth0: tx ring full
[ 527.012000] eth0: tx ring full
[ 527.220000] eth0: tx ring full
[ 527.436000] eth0: tx ring full
[ 527.524000] eth0: tx ring full
[ 527.532000] eth0: tx ring full
[ 530.340000] eth0: tx ring full
[ 530.488000] eth0: tx ring full
[ 530.864000] eth0: tx ring full
[ 531.628000] eth0: tx ring full
[ 531.828000] eth0: tx ring full
[ 532.332000] eth0: tx ring full
[ 533.212000] eth0: tx ring full
[ 533.360000] eth0: tx ring full
[ 533.516000] eth0: tx ring full
[ 533.948000] eth0: tx ring full
[ 534.324000] eth0: tx ring full
[ 535.372000] eth0: tx ring full
[ 535.516000] eth0: tx ring full
[ 535.680000] eth0: tx ring full
[ 535.832000] eth0: tx ring full
[ 537.768000] eth0: tx ring full
[ 540.268000] eth0: tx ring full
[ 542.200000] eth0: tx ring full
[ 542.628000] eth0: tx ring full
[ 542.776000] eth0: tx ring full
[ 544.416000] eth0: tx ring full
[ 544.564000] eth0: tx ring full
[ 544.840000] eth0: tx ring full
[ 544.988000] eth0: tx ring full
[ 545.264000] eth0: tx ring full
[ 546.024000] eth0: tx ring full
[ 547.012000] eth0: tx ring full
[ 547.236000] eth0: tx ring full
[ 547.652000] eth0: tx ring full
[ 547.928000] eth0: tx ring full
[ 547.936000] eth0: tx ring full
[ 548.080000] eth0: tx ring full
[ 548.084000] eth0: tx ring full
[ 548.228000] eth0: tx ring full
[ 548.384000] eth0: tx ring full
[ 548.748000] eth0: tx ring full
[ 548.756000] eth0: tx ring full
[ 549.312000] eth0: tx ring full
[ 549.368000] eth0: tx ring full
[ 549.380000] eth0: tx ring full
[ 550.992000] eth0: tx ring full
[ 551.268000] eth0: tx ring full
[ 551.420000] eth0: tx ring full
[ 551.784000] eth0: tx ring full
[ 552.436000] eth0: tx ring full
[ 552.868000] eth0: tx ring full
[ 552.908000] eth0: tx ring full
[ 553.140000] eth0: tx ring full
[ 553.308000] eth0: tx ring full
[ 555.736000] eth0: tx ring full
[ 555.888000] eth0: tx ring full
[ 556.036000] eth0: tx ring full
[ 556.312000] eth0: tx ring full
[ 556.464000] eth0: tx ring full
[ 556.468000] eth0: tx ring full
[ 556.748000] eth0: tx ring full
[ 557.036000] eth0: tx ring full
[ 557.180000] eth0: tx ring full
[ 557.440000] eth0: tx ring full
[ 557.448000] eth0: tx ring full
[ 557.480000] eth0: tx ring full
[ 557.756000] eth0: tx ring full
[ 557.904000] eth0: tx ring full
[ 558.184000] eth0: tx ring full
[ 558.328000] eth0: tx ring full
[ 558.336000] eth0: tx ring full
[ 561.304000] eth0: tx ring full
[ 562.028000] eth0: tx ring full
[ 562.176000] eth0: tx ring full
[ 562.572000] eth0: tx ring full
[ 562.768000] eth0: tx ring full
[ 563.480000] eth0: tx ring full
[ 563.756000] eth0: tx ring full
[ 563.908000] eth0: tx ring full
[ 566.128000] eth0: tx ring full
[ 566.276000] eth0: tx ring full
[ 566.648000] eth0: tx ring full
[ 566.708000] eth0: tx ring full
[ 566.856000] eth0: tx ring full
[ 567.008000] eth0: tx ring full
[ 567.156000] eth0: tx ring full
[ 567.884000] eth0: tx ring full
[ 568.032000] eth0: tx ring full
[ 568.188000] eth0: tx ring full
[ 568.288000] eth0: tx ring full
[ 568.332000] eth0: tx ring full
[ 571.748000] eth0: tx ring full
[ 572.324000] eth0: tx ring full
[ 572.472000] eth0: tx ring full
[ 572.920000] eth0: tx ring full
[ 573.068000] eth0: tx ring full
[ 573.216000] eth0: tx ring full
[ 573.220000] eth0: tx ring full
[ 573.368000] eth0: tx ring full
[ 573.652000] eth0: tx ring full
[ 573.676000] eth0: tx ring full
[ 574.224000] eth0: tx ring full
[ 575.324000] eth0: tx ring full
[ 576.796000] eth0: tx ring full
[ 577.028000] eth0: tx ring full
[ 577.232000] eth0: tx ring full
[ 577.452000] eth0: tx ring full
[ 578.376000] eth0: tx ring full
[ 580.204000] eth0: tx ring full
[ 580.416000] eth0: tx ring full
[ 582.452000] eth0: tx ring full
[ 582.852000] eth0: tx ring full
[ 583.000000] eth0: tx ring full
[ 583.152000] eth0: tx ring full
[ 583.428000] eth0: tx ring full
[ 583.644000] eth0: tx ring full
[ 584.136000] eth0: tx ring full
[ 585.316000] eth0: tx ring full
[ 585.516000] eth0: tx ring full
[ 585.720000] eth0: tx ring full
[ 585.828000] eth0: tx ring full
[ 585.976000] eth0: tx ring full
[ 587.280000] eth0: tx ring full
[ 587.580000] eth0: tx ring full
[ 587.856000] eth0: tx ring full
[ 588.008000] eth0: tx ring full
[ 588.156000] eth0: tx ring full
[ 588.308000] eth0: tx ring full
[ 588.468000] eth0: tx ring full
[ 588.684000] eth0: tx ring full
[ 588.764000] eth0: tx ring full
[ 589.740000] eth0: tx ring full
[ 589.976000] eth0: tx ring full
[ 590.336000] eth0: tx ring full
[ 590.652000] eth0: tx ring full
[ 591.380000] eth0: tx ring full
[ 591.528000] eth0: tx ring full
[ 591.896000] eth0: tx ring full
[ 591.936000] eth0: tx ring full
[ 592.856000] eth0: tx ring full
[ 592.996000] eth0: tx ring full
[ 593.004000] eth0: tx ring full
[ 593.144000] eth0: tx ring full
[ 593.308000] eth0: tx ring full
[ 593.316000] eth0: tx ring full
[ 596.108000] eth0: tx ring full
[ 596.388000] eth0: tx ring full
[ 596.536000] eth0: tx ring full
[ 596.684000] eth0: tx ring full
[ 596.836000] eth0: tx ring full
[ 596.908000] eth0: tx ring full
[ 597.728000] eth0: tx ring full
[ 598.324000] eth0: tx ring full
[ 600.228000] eth0: tx ring full
[ 600.508000] eth0: tx ring full
[ 600.656000] eth0: tx ring full
[ 600.944000] eth0: tx ring full
[ 600.952000] eth0: tx ring full
[ 601.104000] eth0: tx ring full
[ 601.416000] eth0: tx ring full
[ 601.564000] eth0: tx ring full
[ 601.716000] eth0: tx ring full
[ 601.864000] eth0: tx ring full
[ 602.140000] eth0: tx ring full
[ 603.000000] eth0: tx ring full
[ 603.144000] eth0: tx ring full
[ 604.040000] eth0: tx ring full
[ 604.316000] eth0: tx ring full
[ 604.468000] eth0: tx ring full
[ 604.684000] eth0: tx ring full
[ 604.888000] eth0: tx ring full
[ 604.908000] eth0: tx ring full
[ 605.048000] eth0: tx ring full
[ 605.344000] eth0: tx ring full
[ 605.648000] eth0: tx ring full
[ 607.728000] eth0: tx ring full
[ 608.000000] eth0: tx ring full
[ 608.148000] eth0: tx ring full
[ 608.352000] eth0: tx ring full
[ 608.424000] eth0: tx ring full
[ 608.576000] eth0: tx ring full
[ 608.936000] eth0: tx ring full
[ 609.232000] eth0: tx ring full
[ 609.444000] eth0: tx ring full
[ 609.560000] eth0: tx ring full
[ 609.772000] eth0: tx ring full
[ 610.124000] eth0: tx ring full
[ 610.332000] eth0: tx ring full
[ 610.408000] eth0: tx ring full
[ 610.616000] eth0: tx ring full
[ 611.124000] eth0: tx ring full
[ 612.176000] eth0: tx ring full
[ 612.880000] eth0: tx ring full
[ 612.912000] eth0: tx ring full
[ 612.916000] eth0: tx ring full
[ 613.004000] eth0: tx ring full
[ 613.100000] eth0: tx ring full
[ 613.376000] eth0: tx ring full
[ 613.524000] eth0: tx ring full
[ 613.676000] eth0: tx ring full
[ 613.836000] eth0: tx ring full
[ 614.048000] eth0: tx ring full
[ 614.248000] eth0: tx ring full
[ 614.760000] eth0: tx ring full
[ 614.768000] eth0: tx ring full
[ 616.188000] eth0: tx ring full
[ 616.428000] eth0: tx ring full
[ 616.636000] eth0: tx ring full
[ 617.028000] eth0: tx ring full
[ 617.244000] eth0: tx ring full
[ 617.448000] eth0: tx ring full
[ 618.044000] eth0: tx ring full
[ 618.792000] eth0: tx ring full
[ 618.852000] eth0: tx ring full
[ 619.664000] eth0: tx ring full
[ 619.784000] eth0: tx ring full
[ 619.804000] eth0: tx ring full
[ 621.012000] eth0: tx ring full
[ 621.740000] eth0: tx ring full
[ 622.016000] eth0: tx ring full
[ 622.164000] eth0: tx ring full
[ 622.896000] eth0: tx ring full
[ 625.100000] eth0: tx ring full
[ 625.248000] eth0: tx ring full
[ 625.524000] eth0: tx ring full
[ 626.196000] eth0: tx ring full
[ 626.404000] eth0: tx ring full
[ 626.412000] eth0: tx ring full
[ 628.588000] eth0: tx ring full
[ 628.876000] eth0: tx ring full
[ 629.164000] eth0: tx ring full
[ 629.852000] eth0: tx ring full
[ 630.068000] eth0: tx ring full
[ 630.140000] eth0: tx ring full
[ 630.236000] eth0: tx ring full
[ 630.288000] eth0: tx ring full
[ 630.564000] eth0: tx ring full
[ 630.876000] eth0: tx ring full
[ 631.152000] eth0: tx ring full
[ 631.160000] eth0: tx ring full
[ 631.572000] eth0: tx ring full
[ 631.848000] eth0: tx ring full
[ 632.000000] eth0: tx ring full
[ 635.276000] eth0: tx ring full
[ 635.552000] eth0: tx ring full
[ 635.704000] eth0: tx ring full
[ 636.064000] eth0: tx ring full
[ 636.624000] eth0: tx ring full
[ 636.840000] eth0: tx ring full
[ 637.028000] eth0: tx ring full
[ 637.128000] eth0: tx ring full
[ 637.280000] eth0: tx ring full
[ 637.428000] eth0: tx ring full
[ 637.580000] eth0: tx ring full
[ 637.728000] eth0: tx ring full
[ 637.880000] eth0: tx ring full
[ 638.436000] eth0: tx ring full
[ 638.712000] eth0: tx ring full
[ 638.968000] eth0: tx ring full
[ 639.016000] eth0: tx ring full
[ 639.592000] eth0: tx ring full
[ 639.740000] eth0: tx ring full
[ 640.016000] eth0: tx ring full
[ 640.164000] eth0: tx ring full
[ 642.496000] eth0: tx ring full
[ 642.644000] eth0: tx ring full
[ 642.800000] eth0: tx ring full
[ 643.072000] eth0: tx ring full
[ 646.048000] eth0: tx ring full
[ 646.200000] eth0: tx ring full
[ 646.348000] eth0: tx ring full
[ 646.496000] eth0: tx ring full
[ 646.708000] eth0: tx ring full
[ 646.776000] eth0: tx ring full
[ 646.924000] eth0: tx ring full
[ 647.008000] eth0: tx ring full
[ 647.076000] eth0: tx ring full
[ 647.224000] eth0: tx ring full
[ 647.672000] eth0: tx ring full
[ 647.820000] eth0: tx ring full
[ 647.828000] eth0: tx ring full
[ 651.344000] eth0: tx ring full
[ 654.460000] eth0: tx ring full
[ 654.608000] eth0: tx ring full
[ 654.760000] eth0: tx ring full
[ 655.032000] eth0: tx ring full
[ 655.244000] eth0: tx ring full
[ 655.324000] eth0: tx ring full
[ 655.468000] eth0: tx ring full
[ 656.184000] eth0: tx ring full
[ 656.192000] eth0: tx ring full
[ 656.468000] eth0: tx ring full
[ 656.616000] eth0: tx ring full
[ 657.024000] eth0: tx ring full
[ 657.184000] eth0: tx ring full
[ 657.784000] eth0: tx ring full
[ 658.084000] eth0: tx ring full
[ 658.820000] eth0: tx ring full
[ 658.968000] eth0: tx ring full
[ 659.120000] eth0: tx ring full
[ 659.396000] eth0: tx ring full
[ 659.572000] eth0: tx ring full
[ 660.056000] eth0: tx ring full
[ 660.416000] eth0: tx ring full
[ 660.696000] eth0: tx ring full
[ 660.964000] eth0: tx ring full
[ 661.124000] eth0: tx ring full
[ 661.724000] eth0: tx ring full
[ 662.176000] eth0: tx ring full
[ 662.620000] eth0: tx ring full
[ 662.852000] eth0: tx ring full
[ 662.896000] eth0: tx ring full
[ 663.044000] eth0: tx ring full
[ 663.376000] eth0: tx ring full
[ 663.576000] eth0: tx ring full
[ 664.264000] eth0: tx ring full
[ 664.908000] eth0: tx ring full
[ 664.916000] eth0: tx ring full
[ 665.324000] eth0: tx ring full
[ 665.624000] eth0: tx ring full
[ 665.772000] eth0: tx ring full
[ 665.920000] eth0: tx ring full
[ 665.924000] eth0: tx ring full
[ 666.068000] eth0: tx ring full
[ 666.216000] eth0: tx ring full
[ 666.584000] eth0: tx ring full
[ 667.012000] eth0: tx ring full
[ 667.224000] eth0: tx ring full
[ 668.016000] eth0: tx ring full
[ 669.244000] eth0: tx ring full
[ 671.568000] eth0: tx ring full
[ 671.780000] eth0: tx ring full
[ 672.860000] eth0: tx ring full
[ 673.120000] eth0: tx ring full
[ 673.400000] eth0: tx ring full
[ 673.548000] eth0: tx ring full
[ 673.824000] eth0: tx ring full
[ 673.976000] eth0: tx ring full
[ 674.124000] eth0: tx ring full
[ 675.188000] eth0: tx ring full
[ 676.212000] eth0: tx ring full
[ 676.364000] eth0: tx ring full
[ 676.512000] eth0: tx ring full
[ 676.664000] eth0: tx ring full
[ 676.812000] eth0: tx ring full
[ 676.964000] eth0: tx ring full
[ 677.556000] eth0: tx ring full
[ 681.908000] eth0: tx ring full
[ 682.184000] eth0: tx ring full
[ 683.824000] eth0: tx ring full
[ 684.100000] eth0: tx ring full
[ 684.680000] eth0: tx ring full
[ 684.828000] eth0: tx ring full
[ 684.980000] eth0: tx ring full
[ 685.128000] eth0: tx ring full
[ 685.404000] eth0: tx ring full
[ 685.560000] eth0: tx ring full
[ 685.720000] eth0: tx ring full
[ 685.864000] eth0: tx ring full
[ 686.004000] eth0: tx ring full
[ 687.148000] eth0: tx ring full
[ 687.296000] eth0: tx ring full
[ 687.448000] eth0: tx ring full
[ 688.028000] eth0: tx ring full
[ 688.180000] eth0: tx ring full
[ 688.456000] eth0: tx ring full
[ 688.604000] eth0: tx ring full
[ 689.576000] eth0: tx ring full
cat /sys/kernel/debug/usb/devices pokaż.
t@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.10
S: Manufacturer=Linux 3.10.49 ifxusb_hcd_2
S: Product=IFX USB Controller
S: SerialNumber=ifxusb_hcd_2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=041e ProdID=406c Rev= 6.14
S: Manufacturer=Creative Labs
S: Product=VF0520 Live! Cam Sync
S: SerialNumber=2012060900865
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=0e(video) Sub=03 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=(none)
I: If#= 1 Alt= 1 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=(none)
E: Ad=81(I) Atr=05(Isoc) MxPS=1216 Ivl=125us
I: If#= 1 Alt= 2 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=(none)
E: Ad=81(I) Atr=05(Isoc) MxPS=1600 Ivl=125us
I: If#= 1 Alt= 3 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=(none)
E: Ad=81(I) Atr=05(Isoc) MxPS=2304 Ivl=125us
I: If#= 1 Alt= 4 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=(none)
E: Ad=81(I) Atr=05(Isoc) MxPS=3060 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.10
S: Manufacturer=Linux 3.10.49 ifxusb_hcd_1
S: Product=IFX USB Controller
S: SerialNumber=ifxusb_hcd_1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0951 ProdID=1607 Rev= 2.00
S: Manufacturer=Kingston
S: Product=DataTraveler 2.0
S: SerialNumber=001000000000000000000035
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
root@OpenWrt:~#
kmod-video-uvc zainstaluj bo nie masz sterownika.
a dlaczego mi się to nie chce zainstalować
:~# opkg install kmod-video-gspca-core kmod-video-gspca-uvc
Package kmod-video-gspca-core (3.10.49-1) installed in root is up to date.
Unknown package 'kmod-video-gspca-uvc'.
Collected errors:
* opkg_install_cmd: Cannot install package kmod-video-gspca-uvc.
kmod-video-uvc a nie kmod-video-gspca-uvc. Uważnie to rób.
dalej mi wychodzi a może trzeba wypiąć kamerke z routera
opkg install kmod-video-gspca-core kmod-video-uvc
Package kmod-video-gspca-core (3.10.49-1) installed in root is up to date.
Unknown package 'kmod-video-uvc'.
Collected errors:
* opkg_install_cmd: Cannot install package kmod-video-uvc.
opkg update zrobiłeś?
tak
Pokaż pełny wynik ekranu z
opkg update
opkg install kmod-video-uvc
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → extrot bbluci
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc