Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Luci opkg upgrade
Zaloguj się lub zarejestruj by napisać odpowiedź
Witam ,
na moim WDR3600 bez problemu wgrałem luci-ar71xx-generic-tl-wdr3600-v1-squashfs-factory.bin 
a potem starym przyzwyczajeniem zrobiłem opkg upgrade luci czego efektem jest /cgi-bin/luci = bad gateway . jak można przywrócić stan pakietów do tego po instalacji ??? czy mtd -r erase rootfs_data coś pomoże ??
Nigdy tak nie rób. fistboot i enter.
Dzięki , czyli firstboot przywróci oprogramowanie i konfiguracje do stanu z momentu instalacji ?
PS : i nie rozumie że nie aktualizować pakietów z poziomu opkg ?
tak
rozumie że nie aktualizować pakietów z poziomu opkg ?
A z czego może wynikać ten wykaz pakietów po wpisaniu opkg list-upgradable ??? skoro nie używa się opkg upgrade ???
Można. Co więcej - nie ma nowszej wersji luci bo oni nie kompilują tego na bieżąco, więc nie wiem co tak naprawdę zrobiłeś.
zrobiłem :
opkg list-upgradable
i dostałem listę
luci-app-watchcat - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-qos - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-ddns - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-firewall - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-ssl - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-proto-3g - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-proto-ppp - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-mod-admin-full - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-base - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-commands - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-proto-ipv6 - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-wol - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-upnp - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-proto-relay - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-lib-nixio - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-p910nd - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-i18n-polish - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-i18n-english - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
luci-app-hd-idle - 0.12+git-14.328.38210-ea67bd1-1 - 0.12+svn-r10530-1
I dokładnie tą wersję masz zainstalowaną. Na dodatek jest to dokładnie lista pakietów zainstalowanych w routerze.
PS - ta opcja w ogóle to lista pakietów zainstalowanych ew. możliwych do aktualizacji. Nie że jest nowa wersja do aktualizacji.
No i wszystko jasne A czy jak pojawi się aktualizacja np: samby to gdzieś to zobaczę w Luci ????
mam jeszcze pytanie bo po zrobieniu firstboot planuje zamontowanie exroot-a na /dev/sda1 czy jest jakaś instrukcja ??? bo zabrało mi miejsca na zainstalowanie pakietów do webdava
Kilka na eko.one.pl. Polecam zapoznanie się z tym.
generalnie wszystko zrobiłem zgodnie z instrukcją ba nawet na /mnt/sda1 mam dokładną kopię systemu co więcej :
cat /etc/config/fstab
config global
option anon_swap '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
option anon_mount '1'
config mount
option uuid 'e1c00257-509b-4934-a36b-0093ee4ee560'
option enabled '1'
option device '/dev/sda1'
option fstype 'ext4'
option is_rootfs '1'
config swap
option device '/dev/sda2'
option enabled '1'
config mount
option target '/mnt/sda3'
option uuid 'bccc0059-ceb2-40e6-bc8d-58b7d1a37a0f'
option enabled '1'
option device '/dev/sda3'
option fstype 'ext4'
a i tak po restarcie nie montuje rootfs na /mnt/sda1
co może być nie tak ?????
tego: option is_rootfs '1' już nie ma, po co to dodałeś? to wywal: option device '/dev/sda1'. Na nośniku jest na 100% ext4 system plików?
ok wywaliłem a na /dev/sda1 na 110% jest ext4 lecz reboot i nic ???
PS. ta opcja is_rootfs '1' była tam po tym jak Luci zaznaczyłem że dysk jest rootfs
Bo luci nie jest dostosowane. Nie miałeś tego przez luci zrobić tylko recznie. Pokaż wyniki poleceń
block info
mount
block info
/dev/mtdblock2: UUID="672ef579-1397327d-01f275e6-672c437e" VERSION="4.0" TYPE="squashfs"
/dev/mtdblock3: TYPE="jffs2"
/dev/sda1: UUID="e1c00257-509b-4934-a36b-0093ee4ee560" NAME="EXT_JOURNAL" VERSION="1.0" TYPE="ext4"
/dev/sda2: VERSION="2" TYPE="swap"
/dev/sda3: UUID="bccc0059-ceb2-40e6-bc8d-58b7d1a37a0f" NAME="EXT_JOURNAL" VERSION="1.0" TYPE="ext4"
mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,noatime,lowerdir=/,upperdir=/overlay)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
/dev/sda3 on /mnt/sda3 type ext4 (rw,relatime,data=ordered)
W pierwszej sekcji to z uuid = 'e1c00257-509b-4934-a36b-0093ee4ee560' dodaj config target /overlay
tak ma być ?
vim /etc/config/fstab
config 'global'
option anon_swap '0'
option anon_mount '1'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
config 'mount'
option target '/overlay'
option uuid 'e1c00257-509b-4934-a36b-0093ee4ee560'
option enabled '1'
option fstype 'ext4'
config 'swap'
option device '/dev/sda2'
option enabled '1'
config 'mount'
option target '/mnt/sda3'
option uuid 'bccc0059-ceb2-40e6-bc8d-58b7d1a37a0f'
option enabled '1'
option fstype 'ext4'
tak.
zmieniłem
cat /etc/config/fstab
config 'global'
option anon_swap '0'
option anon_mount '1'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
config 'mount'
option target '/overlay'
option uuid 'e1c00257-509b-4934-a36b-0093ee4ee560'
option enabled '1'
option fstype 'ext4'
config 'swap'
option device '/dev/sda2'
option enabled '1'
config 'mount'
option target '/mnt/sda3'
option uuid 'bccc0059-ceb2-40e6-bc8d-58b7d1a37a0f'
option enabled '1'
option fstype 'ext4'
po reboocie mam
mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,noatime,lowerdir=/,upperdir=/overlay)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
/dev/sda3 on /mnt/sda3 type ext4 (rw,relatime,data=ordered)
czyli bez zmian
zrób
mkdir -p /tmp/dysk
mount -t ext4 /dev/sda1 /tmp/dysk
mount
I pokaż co wyszło z tego.
mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,noatime,lowerdir=/,upperdir=/overlay)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
/dev/sda3 on /mnt/sda3 type ext4 (rw,relatime,data=ordered)
/dev/sda1 on /tmp/dysk type ext4 (rw,relatime,data=ordered)
reboot zrób i wynik logread od razu po starcie.
logread
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.470000] cfg80211: DFS Master region: unset
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.470000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.480000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.490000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.500000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.520000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.520000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.530000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.540000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.640000] u32 classifier
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.640000] input device check on
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.640000] Actions configured
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.650000] Mirror/redirect action on
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.660000] fuse init (API version 7.22)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.690000] usbcore: registered new interface driver cdc_acm
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.700000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.710000] ip_tables: (C) 2000-2006 Netfilter Core Team
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.750000] usbcore: registered new interface driver usblp
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.760000] usbcore: registered new interface driver usbserial
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.770000] usbcore: registered new interface driver usbserial_generic
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.780000] usbserial: USB Serial support registered for generic
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.830000] xt_time: kernel timezone is -0000
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.840000] usbcore: registered new interface driver cdc_ether
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.850000] usbcore: registered new interface driver cdc_ncm
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.870000] PPP generic driver version 2.4.2
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.870000] PPP MPPE Compression module registered
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.880000] NET: Registered protocol family 24
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.880000] PPTP driver version 0.8.5
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.890000] usbcore: registered new interface driver sierra
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.900000] usbserial: USB Serial support registered for Sierra USB modem
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.930000] ath: EEPROM regdomain: 0x0
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.930000] ath: EEPROM indicates default country code should be used
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.930000] ath: doing EEPROM country->regdmn map search
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.930000] ath: country maps to regdmn code: 0x3a
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.930000] ath: Country alpha2 being used: US
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.930000] ath: Regpair used: 0x3a
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.940000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.940000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.950000] cfg80211: Calling CRDA for country: US
Wed Dec 10 09:24:45 2014 kern.warn kernel: [ 18.960000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.970000] ath: EEPROM regdomain: 0x0
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.970000] ath: EEPROM indicates default country code should be used
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.970000] ath: doing EEPROM country->regdmn map search
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.970000] ath: country maps to regdmn code: 0x3a
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.970000] ath: Country alpha2 being used: US
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 18.970000] ath: Regpair used: 0x3a
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.980000] cfg80211: Regulatory domain changed to country: US
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.980000] cfg80211: DFS Master region: FCC
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 18.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.000000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.010000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.020000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.030000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Wed Dec 10 09:24:45 2014 kern.debug kernel: [ 19.040000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.040000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.060000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.060000] usbcore: registered new interface driver option
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.070000] usbserial: USB Serial support registered for GSM modem (1-port)
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 19.530000] Adding 976892k swap on /dev/sda2. Priority:-1 extents:1 across:976892k
Wed Dec 10 09:24:45 2014 kern.info kernel: [ 20.410000] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts:
Wed Dec 10 09:24:48 2014 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Wed Dec 10 09:24:48 2014 user.err syslog: mounting /dev/mtdblock2 (squashfs) as /mnt/mtdblock2 failed (-1) - Unknown error -1
Wed Dec 10 09:24:48 2014 user.err syslog: /dev/mtdblock3 is already mounted
Wed Dec 10 09:24:48 2014 user.emerg syslog: block: mounting /dev/mtdblock2 (squashfs) as /mnt/mtdblock2 failed (-1) - Unknown error -1
Wed Dec 10 09:24:48 2014 user.emerg syslog: block: /dev/mtdblock3 is already mounted
Wed Dec 10 09:24:48 2014 user.err syslog: /dev/sda3 is already mounted
Wed Dec 10 09:24:49 2014 user.emerg syslog: block: /dev/sda3 is already mounted
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.040000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.060000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.060000] device eth0.1 entered promiscuous mode
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.070000] device eth0 entered promiscuous mode
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.070000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'lan' is enabled
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'lan' is setting up now
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'lan' is now up
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'loopback' is enabled
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'loopback' is setting up now
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'loopback' is now up
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.110000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'wan' is enabled
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Network device 'lo' link is up
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'loopback' has link connectivity
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.620000] eth0: link up (1000Mbps/Full duplex)
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.620000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Network device 'eth0' link is up
Wed Dec 10 09:24:51 2014 daemon.notice netifd: VLAN 'eth0.2' link is up
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'wan' has link connectivity
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'wan' is setting up now
Wed Dec 10 09:24:51 2014 daemon.notice netifd: VLAN 'eth0.1' link is up
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.630000] br-lan: port 1(eth0.1) entered forwarding state
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.640000] br-lan: port 1(eth0.1) entered forwarding state
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.640000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.650000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Bridge 'br-lan' link is up
Wed Dec 10 09:24:51 2014 daemon.notice netifd: Interface 'lan' has link connectivity
Wed Dec 10 09:24:51 2014 kern.info kernel: [ 27.700000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Wed Dec 10 09:24:52 2014 daemon.notice netifd: wan (1358): udhcpc (v1.22.1) started
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.700000] cfg80211: Calling CRDA for country: PL
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.720000] cfg80211: Regulatory domain changed to country: PL
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.720000] cfg80211: DFS Master region: ETSI
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.730000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.740000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.740000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.750000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.760000] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
Wed Dec 10 09:24:52 2014 kern.info kernel: [ 28.770000] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Wed Dec 10 09:24:53 2014 daemon.notice netifd: wan (1358): Sending discover...
Wed Dec 10 09:24:53 2014 daemon.notice netifd: wan (1358): Sending select for 89.228.69.183...
Wed Dec 10 09:24:53 2014 daemon.notice netifd: wan (1358): Lease of 89.228.69.183 obtained, lease time 3600
Wed Dec 10 09:24:53 2014 authpriv.warn dropbear[1350]: Failed listening on '22': Error listening: Cannot assign requested address
Wed Dec 10 09:24:53 2014 authpriv.info dropbear[1350]: Not backgrounding
Wed Dec 10 09:24:53 2014 daemon.notice netifd: Interface 'wan6' is enabled
Wed Dec 10 09:24:53 2014 daemon.notice netifd: Network alias 'eth0.2' link is up
Wed Dec 10 09:24:53 2014 daemon.notice netifd: Interface 'wan6' has link connectivity
Wed Dec 10 09:24:53 2014 daemon.notice netifd: Interface 'wan6' is setting up now
Wed Dec 10 09:24:53 2014 daemon.notice netifd: Interface 'wan' is now up
Wed Dec 10 09:24:53 2014 kern.info kernel: [ 29.640000] br-lan: port 1(eth0.1) entered forwarding state
Wed Dec 10 09:24:55 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Wed Dec 10 09:24:55 2014 kern.info kernel: [ 31.330000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Wed Dec 10 09:24:55 2014 kern.info kernel: [ 31.370000] device wlan1 entered promiscuous mode
Wed Dec 10 09:24:55 2014 kern.info kernel: [ 31.440000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Wed Dec 10 09:24:55 2014 kern.info kernel: [ 31.580000] device wlan0 entered promiscuous mode
Wed Dec 10 09:24:55 2014 kern.info kernel: [ 31.590000] br-lan: port 3(wlan0) entered forwarding state
Wed Dec 10 09:24:55 2014 kern.info kernel: [ 31.590000] br-lan: port 3(wlan0) entered forwarding state
Wed Dec 10 09:24:55 2014 user.info syslog: module is already loaded - xt_comment
Wed Dec 10 09:24:55 2014 kern.emerg already loaded - xt_comment
Wed Dec 10 09:24:56 2014 kern.info kernel: [ 32.350000] br-lan: port 3(wlan0) entered disabled state
Wed Dec 10 09:24:56 2014 kern.info kernel: [ 32.900000] br-lan: port 2(wlan1) entered forwarding state
Wed Dec 10 09:24:56 2014 kern.info kernel: [ 32.900000] br-lan: port 2(wlan1) entered forwarding state
Wed Dec 10 09:24:56 2014 kern.info kernel: [ 32.910000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Wed Dec 10 09:24:57 2014 daemon.notice netifd: Network device 'wlan1' link is up
Wed Dec 10 09:24:58 2014 user.info syslog: module is already loaded - xt_comment
Wed Dec 10 09:24:58 2014 kern.emerg already loaded - xt_comment
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.210000] br-lan: port 3(wlan0) entered forwarding state
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.210000] br-lan: port 3(wlan0) entered forwarding state
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.220000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.240000] device wlan0-1 entered promiscuous mode
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.250000] br-lan: port 4(wlan0-1) entered forwarding state
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.250000] br-lan: port 4(wlan0-1) entered forwarding state
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.260000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
Wed Dec 10 09:24:58 2014 kern.info kernel: [ 34.900000] br-lan: port 2(wlan1) entered forwarding state
Wed Dec 10 09:24:59 2014 kern.info kernel: [ 35.100000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
Wed Dec 10 09:24:59 2014 daemon.notice netifd: Network device 'wlan0' link is up
Wed Dec 10 09:24:59 2014 daemon.notice netifd: Network device 'wlan0-1' link is up
Wed Dec 10 09:25:00 2014 kern.info kernel: [ 36.210000] br-lan: port 3(wlan0) entered forwarding state
Wed Dec 10 09:25:00 2014 kern.info kernel: [ 36.250000] br-lan: port 4(wlan0-1) entered forwarding state
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: started, version 2.71 cachesize 150
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq-dhcp[1915]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: using local addresses only for domain lan
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: reading /tmp/resolv.conf.auto
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: using local addresses only for domain lan
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: using nameserver 217.172.224.160#53
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: using nameserver 89.231.1.206#53
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: read /etc/hosts - 1 addresses
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq[1915]: read /tmp/hosts/dhcp - 1 addresses
Wed Dec 10 09:25:01 2014 daemon.info dnsmasq-dhcp[1915]: read /etc/ethers - 0 addresses
Wed Dec 10 09:25:01 2014 daemon.crit xl2tpd[1920]: setsockopt recvref[30]: Protocol not available
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1920]: Using l2tp kernel support.
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1929]: xl2tpd version xl2tpd-1.3.6 started on OpenWrt PID:1929
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1929]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc.
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1929]: Forked by Scott Balmos and David Stipp, (C) 2001
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1929]: Inherited by Jeff McAdams, (C) 2002
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1929]: Forked again by Xelerance (www.xelerance.com) (C) 2006
Wed Dec 10 09:25:01 2014 daemon.info xl2tpd[1929]: Listening on IP address 0.0.0.0, port 1701
Wed Dec 10 09:25:02 2014 user.emerg syslog: setting up led USB1
Wed Dec 10 09:25:02 2014 user.emerg syslog: setting up led USB2
Wed Dec 10 09:25:02 2014 user.emerg syslog: setting up led WLAN2G
Wed Dec 10 09:25:02 2014 daemon.err miniupnpd[1983]: could not open lease file: /var/upnp.leases
Wed Dec 10 09:25:02 2014 daemon.notice miniupnpd[1983]: HTTP listening on port 5000
Wed Dec 10 09:25:02 2014 daemon.notice miniupnpd[1983]: HTTP IPv6 address given to control points : [fdf2:8681:a549::1]
Wed Dec 10 09:25:02 2014 daemon.notice miniupnpd[1983]: Listening for NAT-PMP/PCP traffic on port 5351
Wed Dec 10 09:25:02 2014 user.info watchcat: starting all tasks
Wed Dec 10 09:25:02 2014 user.info wathchat: started task (mode=ping;period=21600;pinghosts=8.8.8.8;pingperiod=1080;forcedelay=30)
Wed Dec 10 09:25:02 2014 user.info watchcat: all tasks started
Wed Dec 10 09:25:03 2014 user.emerg syslog: - init complete -
Wed Dec 10 09:25:05 2014 user.notice mwan3: ifup interface wan (eth0.2)
Wed Dec 10 09:25:06 2014 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Wed Dec 10 09:25:08 2014 daemon.notice miniupnpd[1983]: shutting down MiniUPnPd
Wed Dec 10 09:25:08 2014 daemon.err miniupnpd[2551]: could not open lease file: /var/upnp.leases
Wed Dec 10 09:25:08 2014 daemon.notice miniupnpd[2551]: HTTP listening on port 5000
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Luci opkg upgrade
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc