Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → problem z openVPN na Gargoyle
Zaloguj się lub zarejestruj by napisać odpowiedź
Zainstalowałem openVPN zgodnie z instrukcją http://eko.one.pl/?p=openwrt-openvpn na najnowszym obrazie Gargoyle PL na TL-WR1043ND.
Przy podłączaniu się klientem z Windowsa 7 pojawia się komunikat:
Fri Nov 26 00:05:03 2010 UDPv4 link remote: 192.168.1.100:1194
a następnie ruter resetuje się 
Jak próbowałem na wersji Gargoyle z ich strony ale wtedy wywala się przy instalacji openVPN. coś z tap.
Jakaś rada?
Zainstalować czyste openwrt?
Właśnie zainstalowałem to z http://ecco.selfip.net/backfire/
efekt:
root@Gargoyle:~# opkg update
Downloading http://downloads.openwrt.org/backfire/1 … ckages.gz.
Inflating http://downloads.openwrt.org/backfire/1 … ckages.gz.
Updated list of available packages in /var/opkg-lists/packages.
root@Gargoyle:~# opkg install openvpn
Installing openvpn (2.1.1-1) to root...
Downloading http://downloads.openwrt.org/backfire/1 … r71xx.ipk.
Installing kmod-tun (2.6.32.10-1) to root...
Downloading http://downloads.openwrt.org/backfire/1 … r71xx.ipk.
Not downgrading package kernel on root from 2.6.32.25-1 to 2.6.32.10-1.
Configuring kmod-tun.
Collected errors:
* opkg_install_cmd: Cannot install package openvpn.
root@Gargoyle:~#
Zmien sobie repo w /etc/opkg.conf z 10.03 na 10.03.1-rc4 i ponów operację.
PS. Co konkretnie zainstalowałeś czy zmodyfikowałeś? Wszystkie moje obrazy mają rc4 domyślnie ustawione.
Nic :]
Wychodzi na to, że podgrywanie obrazów na zasadzie
wget obraz.bin
sysupgrade obraz.bin
nie usuwa plików konfiguracji.
Pewnie to oczywista oczywistość;-)
Jeżeli zażądałeś zachowana konfiguracji to tak...
Zmiana repozytorium pomogła. Dzięki:)
Przy uruchamianiu skryptu /etc/init.d/openvpn-startup wywala
root@Gargoyle:~# chmod 755 /etc/init.d/openvpn-startup
root@Gargoyle:~# /etc/init.d/openvpn-startup enable
root@Gargoyle:~# /etc/init.d/openvpn-startup start
Fri Nov 26 11:19:08 2010 Note: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
Fri Nov 26 11:19:08 2010 Note: Attempting fallback to kernel 2.2 TUN/TAP interface
Fri Nov 26 11:19:08 2010 Cannot open TUN/TAP dev /dev/tap0: No such file or directory (errno=2)
Fri Nov 26 11:19:08 2010 Exiting
brctl: iface tap0: No such device
ifconfig: SIOCSIFADDR: No such device
root@Gargoyle:~# /etc/init.d/openvpn-startup start
Fri Nov 26 11:20:10 2010 Note: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
Fri Nov 26 11:20:10 2010 Note: Attempting fallback to kernel 2.2 TUN/TAP interface
Fri Nov 26 11:20:10 2010 Cannot open TUN/TAP dev /dev/tap0: No such file or directory (errno=2)
Fri Nov 26 11:20:10 2010 Exiting
brctl: iface tap0: No such device
ifconfig: SIOCSIFADDR: No such device
root@Gargoyle:~#
Tak jak byś tun nie miał załadowanego w modułach. lsmod | grep tun.
Zgadza się:]
root@Gargoyle:/sbin# lsmod | grep tun
root@Gargoyle:/sbin# lsmod | grep tun
root@Gargoyle:/sbin#
root@Gargoyle:/sbin# insmod tun
root@Gargoyle:/sbin# lsmod | grep tun
opkg list_installed | grep kmod pokaż.
zrobiłem to po partyzancku ale pomogło.
Znaczy sysugrade z wyczyszczeniem konfiguracji.
/etc/init.d/openvpn start
wskoczyło bez problemu.
Tak że
/etc/init.d/openvpn-startup start
też ruszyło.
Tyle, że dalej jak się łączę z lokala czyli z 192.168.1.x na router 192.168.1.100 to mi się resetuje TP-Link
Jak łączę się z zewnątrz przez modem play w telefonie przy DMZ ustawionym na TP-Linka to nic się nie dzieje:/
Fri Nov 26 12:32:13 2010 OpenVPN 2.1.1 i686-pc-mingw32 [SSL] [LZO2] [PKCS11] built on Dec 11 2009
Fri Nov 26 12:32:13 2010 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables
Fri Nov 26 12:32:13 2010 Static Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Fri Nov 26 12:32:13 2010 Static Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri Nov 26 12:32:13 2010 Static Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Fri Nov 26 12:32:13 2010 Static Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Fri Nov 26 12:32:14 2010 TAP-WIN32 device [Local Area Connection 5] opened: \\.\Global\{27FDA97C-5B82-4CB0-8655-0E5881B9BA6F}.tap
Fri Nov 26 12:32:14 2010 TAP-Win32 Driver Version 9.6
Fri Nov 26 12:32:14 2010 TAP-Win32 MTU=1500
Fri Nov 26 12:32:14 2010 NOTE: FlushIpNetTable failed on interface [29] {27FDA97C-5B82-4CB0-8655-0E5881B9BA6F} (status=5) : Access is denied.
Fri Nov 26 12:32:14 2010 Data Channel MTU parms [ L:1576 D:1450 EF:44 EB:4 ET:32 EL:0 ]
Fri Nov 26 12:32:14 2010 Local Options hash (VER=V4): '8b888ddc'
Fri Nov 26 12:32:14 2010 Expected Remote Options hash (VER=V4): '8b888ddc'
Fri Nov 26 12:32:14 2010 Socket Buffers: R=[8192->8192] S=[8192->8192]
Fri Nov 26 12:32:14 2010 UDPv4 link local: [undef]
Fri Nov 26 12:32:14 2010 UDPv4 link remote: 87.205.142.72:1194
Tak BTW powiem Ci, że to kiedyś działało na tym routerze z inną wersją openwrt.
Tu masz opkg list_installed | grep kmod
root@OpenWrt:~# opkg list_installed | grep kmod
kmod-ath - 2.6.32.25+2010-10-19-1
kmod-ath9k - 2.6.32.25+2010-10-19-1
kmod-button-hotplug - 2.6.32.25-1
kmod-cfg80211 - 2.6.32.25+2010-10-19-1
kmod-crc-ccitt - 2.6.32.25-1
kmod-crc16 - 2.6.32.25-1
kmod-crypto-aes - 2.6.32.25-1
kmod-crypto-arc4 - 2.6.32.25-1
kmod-crypto-core - 2.6.32.25-1
kmod-fs-ext2 - 2.6.32.25-1
kmod-fs-ext3 - 2.6.32.25-1
kmod-fs-ext4 - 2.6.32.25-1
kmod-fs-mbcache - 2.6.32.25-1
kmod-fs-vfat - 2.6.32.25-1
kmod-fuse - 2.6.32.25-1
kmod-input-core - 2.6.32.25-1
kmod-input-gpio-buttons - 2.6.32.25-1
kmod-input-polldev - 2.6.32.25-1
kmod-ipt-conntrack - 2.6.32.25-1
kmod-ipt-core - 2.6.32.25-1
kmod-ipt-nat - 2.6.32.25-1
kmod-ipt-nathelper - 2.6.32.25-1
kmod-leds-gpio - 2.6.32.25-1
kmod-mac80211 - 2.6.32.25+2010-10-19-1
kmod-nls-base - 2.6.32.25-1
kmod-nls-cp437 - 2.6.32.25-1
kmod-nls-iso8859-1 - 2.6.32.25-1
kmod-ppp - 2.6.32.25-1
kmod-pppoe - 2.6.32.25-1
kmod-scsi-core - 2.6.32.25-1
kmod-tun - 2.6.32.25-1
kmod-usb-core - 2.6.32.25-1
kmod-usb-storage - 2.6.32.25-1
kmod-usb2 - 2.6.32.25-1
Plik /tmp/openvpn-status.log
penVPN STATISTICS
Updated,Fri Nov 26 12:28:22 2010
TUN/TAP read bytes,0
TUN/TAP write bytes,0
TCP/UDP read bytes,0
TCP/UDP write bytes,0
Auth read bytes,0
END
Odblokowane masz porty na wanie?
Fragment /etc/config/firewall
config 'rule'
option '_name' 'openvpn'
option 'src' 'wan'
option 'target' 'ACCEPT'
option 'proto' 'udp'
option 'dest_port' '1194'
/etc/firewall.user
# This file is interpreted as shell script.
# Put your custom iptables rules here, they will
# be executed with each firewall (re-)start.iptables -I OUTPUT -o tap+ -j ACCEPT
iptables -I INPUT -i tap+ -j ACCEPT
iptables -I FORWARD -o tap+ -j ACCEPT
iptables -I FORWARD -i tap+ -j ACCEPT
Ty pytanie czy przez siec playową bez problemu udp przechodzi...
Pytanie dobre 
Tyle że to już działało.
Inne pytanie czemu router się resetuje przy podłączaniu via lan?
Moge jakoś uruchomić openvpn w trybie debug vie putty z innego kompa i zobaczyć co się dzieje zanim się resetuje ?
--verb n możesz. ale raczej rsem, bo nie wiem czy po sieci to złapiesz (może np. kernel się wywala).
Nic się nie pojawiło
root@OpenWrt:~# ps | grep openvpn
1275 root 2928 R /usr/sbin/openvpn --syslog openvpn(myvpn) --writepid
1393 root 1352 S grep openvpn
root@OpenWrt:~# kill 1275
root@OpenWrt:~# ps | grep openvpn
1413 root 1352 S grep openvpn
root@OpenWrt:~# openvpn --verb n
Options error: You must define TUN/TAP device (--dev)
Use --help for more information.
root@OpenWrt:~# openvpn --verb n --dev tap
Fri Nov 26 12:55:37 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port.
Fri Nov 26 12:55:37 2010 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables
Fri Nov 26 12:55:37 2010 ******* WARNING *******: all encryption and authentication features disabled -- all data will be tunnelled as cleartext
-verb 5 np.
a no ok
daję openvpn --verb 5 --dev tap
i na konsolę lecą literki "rrrrrrrrrrrrrrrrrrrrrrrr"
lecą i lecą:)
Podłączenie się po lokalu daje tyle że przestają lecieć. Oczywiście jak następuje reset :]
co to jest ten "rsem" ?
Jak się łączę z zewnątrz to też się teraz resetuje TP-Link.
Problemem był dyndns który nie odświeżył mojego zmiennego IP :]
[UPnP set event: Public_UPNP_C3] from source 192.168.1.104, Wednesday, Jan 01,2003 21:50:46
[DHCP IP: (192.168.1.103)] to MAC address 00:22:FB:C2:4B:AA, Wednesday, Jan 01,2003 21:50:42
[DHCP IP: (192.168.1.107)] to MAC address 00:90:F5:4E:B8:20, Wednesday, Jan 01,2003 21:50:39
[UPnP set event: Public_UPNP_C3] from source 192.168.1.102, Wednesday, Jan 01,2003 21:50:31
Firewall: packet accept. 46.112.36.38(64590) --> 178.37.149.59(1194), Protocol UDP.
Wednesday, Jan 01,2003 21:50:27
[UPnP set event: Public_UPNP_C3] from source 192.168.1.104, Wednesday, Jan 01,2003 21:50:13
[Log Cleared] Wednesday, Jan 01,2003 21:50:06
Ja na dzisiaj muszę dać spokój z tematem.
Wielkie dzięki za pomoc.
To zmniejsz tą cyferkę, to poziom debugu.
rsem, kablem szeregowym, rs232c.
No kabelek posiadam.
Zajmę się tym pewnie koło niedzieli.
Jeszcze raz dzięki:)
Podłączyłem się kablem rs.
To wypluwa w czasie startu systemu
U-Boot 1.1.4 (Nov 17 2009 - 11 begin_of_the_skype_highlighting 17 2009 - 11 end_of_the_skype_highlighting:56:26)
AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environmentIn: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... OKStarting kernel ...
Linux version 2.6.32.25 (cezary@eko.one.pl) (gcc version 4.3.3 (GCC) ) #37 Wed Nov 24 15:37:44 CET 2010
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR9132 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=TL-WR1043ND
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29356k/32768k available (2067k kernel code, 3412k reserved, 390k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR1043ND
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) Š 2001-2006 Red Hat, Inc.
yaffs Nov 13 2010 09:51:54 Installing.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: s25sl064a (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=420000, len=3D0000
0x000000420000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
Realtek RTL8366RB ethernet switch driver version 0.2.2
rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
rtl8366rb: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 152k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
eth0: link up (1000Mbps/Full duplex)
- preinit -
Registered led device: tl-wr1043nd:green:usb
Registered led device: tl-wr1043nd:green:system
Registered led device: tl-wr1043nd:green:qss
Registered led device: tl-wr1043nd:green:wlan
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -
eth0: link downPlease press Enter to activate this console. eth0: link up (1000Mbps/Full duplex)
Compat-wireless backport release: compat-wireless-2010-10-14-7-gab01eca
Backport based on wireless-testing.git master-2010-10-19
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entering forwarding state
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:0 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (461 buckets, 1844 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
fuse init (API version 7.13)
a to przy próbie podłączenia klientem openvnc z windows 7.
USB Mass Storage support registered.
fuse init (API version 7.13)
^C
Please press Enter to activate this console. ------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:101 0x801856d0()
autorequest GPIO-0
Modules linked in: fuse usb_storage nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack ehci_hcd sd_mod pppoe pppox ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ext2 ext3 jbd tun ppp_async ppp_generic slhc vfat fat ext4 jbd2 ath9k ath9k_common ath9k_hw ath nls_iso8859_1 nls_cp437 mac80211 usbcore scsi_mod nls_base mbcache crc16 crc_ccitt cfg80211 compat_firmware_class compat arc4 aes_generic deflate ecb cbc leds_gpio button_hotplug gpio_buttons input_polldev input_core
Call Trace:[<8007d914>] 0x8007d914
[<80068374>] 0x80068374
[<80068374>] 0x80068374
[<8007cf1c>] 0x8007cf1c
[<801856d0>] 0x801856d0
[<8007cf9c>] 0x8007cf9c
[<80213458>] 0x80213458
[<80212c74>] 0x80212c74
[<801856d0>] 0x801856d0
[<80212fbc>] 0x80212fbc
[<8018580c>] 0x8018580c
[<801cf854>] 0x801cf854
[<801cff30>] 0x801cff30
[<800af17c>] 0x800af17c
[<801d0810>] 0x801d0810
[<800af244>] 0x800af244
[<801ec328>] 0x801ec328
[<800e9c78>] 0x800e9c78
[<801ec428>] 0x801ec428
[<801def68>] 0x801def68
[<801ecb94>] 0x801ecb94
[<8008295c>] 0x8008295c
[<80082a3c>] 0x80082a3c
[<801ecce4>] 0x801ecce4
[<808ddce0>] 0x808ddce0
[<800d9058>] 0x800d9058
[<800925a4>] 0x800925a4
[<80072ae4>] 0x80072ae4
[<800d9ca0>] 0x800d9ca0
[<800d9e58>] 0x800d9e58
[<800e8f74>] 0x800e8f74
[<80062544>] 0x80062544
[<80082070>] 0x80082070---[ end trace 30892e79d044d39a ]---
gpio? wyładuj wszystkie moduły z tym związane (button, led) i zobacz.
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → problem z openVPN na Gargoyle
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc