• Zarejestrowany: 2014-09-17
  • Posty: 10

Temat: 1wire DS9490R jak uruchomić?

Mając chwile wolnego czasu na zwolnieniu chorobowym postanowiłem zrobić cos porzytecznego ze starego routera WL-500W i interfejsu 1-wire DS9490R ale nie mogę uruchomić USB pod OpenWrt, czy możecie koledzy pomóc?

Zainstalowałem OpenWrt Barrier Breaker 14.07-rc3 doinstalowałem do niego
owshell 2.9p5-1
owserver 2.9p5-1
owhttpd 2.9p5-1
owfs 2.9p5-1
kmod-w1-master-ds2490 3.10.49-1
kmod-w1 3.10.49-1
kmod-usb-core 3.10.49-1
kmod-usb-brcm47xx 3.10.49-1

i niestety nadal nie widzę ttyUSB. Kiedyś bawiłem się na tomato tą samą przelotką i digitem i było ok.

Proszę o pomoc co można z tym zrobić, wydaje mi się iż w ogóle nie widzę usb. Poniżej wynik dmesg


---
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41989) ) #1 Fri Aug 8 01:10:15 CEST 2014
[ 0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00
[ 0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
[ 0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[ 0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[ 0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
[ 0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
[ 0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
[ 0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
[ 0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
[ 0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
[ 0.000000] ssb: chipcommon status is 0x0
[ 0.000000] ssb: Initializing MIPS core...
[ 0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[ 0.000000] ssb: set_irq: core 0x0806, irq 5 => 5
[ 0.000000] ssb: set_irq: core 0x0808, irq 6 => 2
[ 0.000000] ssb: set_irq: core 0x0804, irq 2 => 6
[ 0.000000] ssb: after irq reconfiguration
[ 0.000000] ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
[ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
[ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4 5* 6 D I
[ 0.000000] ssb: core 0x0808, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x0804, irq : 2(S) 3 4 5 6* D I
[ 0.000000] ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x0807, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x080b, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Asus WL500W
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802e6b80, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28936k/32768k available (2453k kernel code, 3832k reserved, 597k data, 208k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.070000] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.110000] bio: create slab <bio-0> at 0
[ 0.120000] Switching to clocksource MIPS
[ 0.130000] ssb: PCIcore in host mode found
[ 0.430000] PCI host bridge to bus 0000:00
[ 0.430000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.430000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.430000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.430000] pci 0000:00:00.0: [14e4:4704] type 00 class 0x060000
[ 0.430000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.430000] pci 0000:00:00.0: setting latency timer to 64
[ 0.430000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.430000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.430000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
[ 0.430000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
[ 0.430000] pci 0000:00:02.0: [14e4:4329] type 00 class 0x028000
[ 0.430000] pci 0000:00:02.0: reg 10: [mem 0x00000000-0x00003fff]
[ 0.430000] pci 0000:00:03.0: [1106:3038] type 00 class 0x0c0300
[ 0.430000] pci 0000:00:03.0: reg 20: [io 0xfce0-0xfcff]
[ 0.430000] pci 0000:00:03.0: supports D1 D2
[ 0.430000] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.440000] pci 0000:00:03.1: [1106:3038] type 00 class 0x0c0300
[ 0.440000] pci 0000:00:03.1: reg 20: [io 0xfce0-0xfcff]
[ 0.440000] pci 0000:00:03.1: supports D1 D2
[ 0.440000] pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
[ 0.440000] pci 0000:00:03.2: [1106:3104] type 00 class 0x0c0320
[ 0.440000] pci 0000:00:03.2: reg 10: [mem 0x00000000-0x000000ff]
[ 0.440000] pci 0000:00:03.2: supports D1 D2
[ 0.440000] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
[ 0.440000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.440000] pci 0000:00:02.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.440000] pci 0000:00:03.2: BAR 0: assigned [mem 0x40004000-0x400040ff]
[ 0.440000] pci 0000:00:03.0: BAR 4: assigned [io 0x0400-0x041f]
[ 0.440000] pci 0000:00:03.1: BAR 4: assigned [io 0x0420-0x043f]
[ 0.450000] PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
[ 0.450000] ssb: PCI: Fixing up device 0000:00:02.0
[ 0.450000] b43-pci-bridge 0000:00:02.0: setting latency timer to 64
[ 0.490000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.490000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x12, vendor 0x4243)
[ 0.490000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0B, vendor 0x4243)
[ 0.490000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x02, vendor 0x4243)
[ 0.490000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
[ 0.490000] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[ 0.530000] ssb: chipcommon status is 0x0
[ 0.530000] ssb: SPROM offset is 0x1000
[ 0.540000] ssb: SPROM revision 4 detected
[ 0.580000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
[ 0.580000] NET: Registered protocol family 2
[ 0.580000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.580000] TCP: Hash tables configured (established 512 bind 512)
[ 0.590000] TCP: reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.590000] NET: Registered protocol family 1
[ 0.590000] PCI: CLS 0 bytes, default 16
[ 0.600000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.600000] msgmni has been set to 56
[ 0.600000] io scheduler noop registered
[ 0.600000] io scheduler deadline registered (default)
[ 0.600000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.640000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
[ 0.990000] console [ttyS0] enabled
[ 1.020000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
[ 1.030000] physmap platform flash device: 02000001 at 1c000000
[ 1.040000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001301
[ 1.050000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[ 1.050000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 1.050000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[ 1.050000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.050000] Amd/Fujitsu Extended Query version 1.3.
[ 1.060000] number of CFI chips: 1
[ 1.080000] 5 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.090000] Creating 5 MTD partitions on "physmap-flash.0":
[ 1.090000] 0x000000000000-0x000000040000 : "boot"
[ 1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.110000] 0x00000004001c-0x0000001bd000 : "linux"
[ 1.120000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.140000] 0x0000001bd000-0x0000007f0000 : "rootfs"
[ 1.140000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.160000] mtd: device 3 (rootfs) set to be root filesystem
[ 1.160000] mtd: partition "rootfs_data" created automatically, ofs=0x400000, len=0x3f0000
[ 1.170000] 0x000000400000-0x0000007f0000 : "rootfs_data"
[ 1.180000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.210000] libphy: Fixed MDIO Bus: probed
[ 1.210000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.220000] GPIO_WDT: failed to register misc device
[ 1.230000] TCP: cubic registered
[ 1.230000] NET: Registered protocol family 17
[ 1.240000] Bridge firewalling registered
[ 1.240000] 8021q: 802.1Q VLAN Support v1.8
[ 1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.270000] Freeing unused kernel memory: 208K (802fc000 - 80330000)
[ 5.000000] pps_core: LinuxPPS API ver. 1 registered
[ 5.000000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.020000] PTP clock support registered
[ 5.030000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[ 5.040000] libphy: b44_eth_mii: probed
[ 5.120000] b53_common: found switch: BCM5325, rev 0
[ 5.130000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bushy_addr=1:1e)
[ 5.140000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1b:fc:bf:f1:7f
[ 5.150000] libphy: b44_eth_mii: probed
[ 5.150000] b44 ssb0:1: could not find PHY at 4, use fixed one
[ 5.160000] b44 ssb0:1: attached PHY driver [Generic PHY] (mii_bushy_addr=fixed-0:00)
[ 5.170000] b44 ssb0:1 eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:90:4c:a1:00:2d
[ 5.180000] bgmac: Broadcom 47xx GBit MAC driver loaded
[ 5.970000] b44 ssb0:0 eth0: Link is down
[ 6.980000] b44 ssb0:0 eth0: Link is down
[ 7.130000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[ 7.130000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[ 11.870000] jffs2: notice: (253) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead, 5 orphan) found.
[ 12.930000] usbcore: registered new interface driver usbfs
[ 12.940000] usbcore: registered new interface driver hub
[ 12.940000] usbcore: registered new device driver usb
[ 13.140000] SCSI subsystem initialized
[ 13.160000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.170000] ehci-platform: EHCI generic platform driver
[ 13.190000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.190000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[ 13.200000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 1
[ 13.210000] ohci-platform ohci-platform.0: irq 2, io mem 0x18003000
[ 13.270000] hub 1-0:1.0: USB hub found
[ 13.280000] hub 1-0:1.0: 2 ports detected
[ 13.300000] usbcore: registered new interface driver usb-storage
[ 13.600000] b44 ssb0:0 eth0: powering down PHY
[ 14.270000] b44 ssb0:0 eth0: Link is down
[ 19.270000] NET: Registered protocol family 10
[ 19.320000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[ 19.420000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 19.450000] fuse init (API version 7.22)
[ 19.460000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 19.470000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 19.490000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.550000] usbcore: registered new interface driver usblp
[ 19.560000] Driver for 1-wire Dallas network protocol.
[ 19.620000] xt_time: kernel timezone is -0000
[ 19.680000] cfg80211: Calling CRDA to update world regulatory domain
[ 19.680000] cfg80211: World regulatory domain updated:
[ 19.690000] cfg80211: DFS Master region: unset
[ 19.690000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.700000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.710000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.720000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.740000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 19.750000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 19.750000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.760000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 19.780000] usbcore: registered new interface driver DS9490R
[ 19.920000] PPP generic driver version 2.4.2
[ 19.940000] NET: Registered protocol family 24
[ 19.990000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 20.060000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 20.070000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2055, Revision 4, Version 0
[ 20.100000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 20.270000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
[ 20.290000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 25.990000] b44 ssb0:0 eth0: Link is down
[ 26.000000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.990000] b44 ssb0:0 eth0: Link is down
[ 27.570000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[ 27.580000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[ 28.030000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 33.110000] b44 ssb0:0 eth0: powering down PHY
[ 33.140000] b44 ssb0:0 eth0: Link is down
[ 33.140000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 33.230000] device eth0 entered promiscuous mode
[ 33.230000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 33.330000] b44 ssb0:1 eth1: Link is down
[ 33.330000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 34.140000] b44 ssb0:0 eth0: Link is down
[ 34.330000] b44 ssb0:1 eth1: Link is down
[ 34.850000] br-lan: port 1(eth0) entered forwarding state
[ 34.860000] br-lan: port 1(eth0) entered forwarding state
[ 34.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 35.300000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 35.300000] b44 ssb0:1 eth1: Link is up at 100 Mbps, full duplex
[ 35.310000] b44 ssb0:1 eth1: Flow control is off for TX and off for RX
[ 35.340000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 36.860000] br-lan: port 1(eth0) entered forwarding state
root@OpenWrt:~#

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,698

Odp: 1wire DS9490R jak uruchomić?

kmod-usb2 i kmod-uhci zainstaluj

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

Zainstalowałem pakiety, aktualny stan pakietów

base-files - 155-r42056
block-mount - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
busybox - 1.22.1-2
dnsmasq - 2.71-3
dropbear - 2014.63-1
firewall - 2014-07-19
fstools - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
fuse-utils - 2.9.0-2
glib2 - 2.41.1-2
hostapd-common - 2014-06-03-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iw - 3.15-1
iwinfo - 50
jshn - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.10.49-1-5d0d3deed34436ecea1e7580c1aae878
kmod-b43 - 3.10.49+2014-05-22-1
kmod-b43legacy - 3.10.49+2014-05-22-1
kmod-b44 - 3.10.49-1
kmod-bgmac - 3.10.49-1
kmod-cfg80211 - 3.10.49+2014-05-22-1
kmod-crypto-aes - 3.10.49-1
kmod-crypto-arc4 - 3.10.49-1
kmod-crypto-core - 3.10.49-1
kmod-crypto-hash - 3.10.49-1
kmod-fs-ext4 - 3.10.49-1
kmod-fs-vfat - 3.10.49-1
kmod-fuse - 3.10.49-1
kmod-gpio-button-hotplug - 3.10.49-1
kmod-hwmon-core - 3.10.49-1
kmod-ip6tables - 3.10.49-1
kmod-ipt-conntrack - 3.10.49-1
kmod-ipt-core - 3.10.49-1
kmod-ipt-nat - 3.10.49-1
kmod-ipt-nathelper - 3.10.49-1
kmod-ipv6 - 3.10.49-1
kmod-leds-gpio - 3.10.49-1
kmod-ledtrig-default-on - 3.10.49-1
kmod-ledtrig-netdev - 3.10.49-1
kmod-ledtrig-timer - 3.10.49-1
kmod-lib-crc-ccitt - 3.10.49-1
kmod-lib-crc16 - 3.10.49-1
kmod-mac80211 - 3.10.49+2014-05-22-1
kmod-mii - 3.10.49-1
kmod-nls-base - 3.10.49-1
kmod-nls-cp437 - 3.10.49-1
kmod-nls-iso8859-1 - 3.10.49-1
kmod-ppp - 3.10.49-1
kmod-pppoe - 3.10.49-1
kmod-pppox - 3.10.49-1
kmod-pps - 3.10.49-1
kmod-ptp - 3.10.49-1
kmod-slhc - 3.10.49-1
kmod-tg3 - 3.10.49-1
kmod-usb-brcm47xx - 3.10.49-1
kmod-usb-core - 3.10.49-1
kmod-usb-ohci - 3.10.49-1
kmod-usb-printer - 3.10.49-1
kmod-usb-uhci - 3.10.49-1
kmod-usb2 - 3.10.49-1
kmod-w1 - 3.10.49-1
kmod-w1-master-ds2490 - 3.10.49-1
libattr - 20140610-1
libblobmsg-json - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libc - 0.9.33.2-1
libffi - 3.0.13-1
libfuse - 2.9.0-2
libgcc - 4.8-linaro-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 50
libiwinfo-lua - 50
libjson-c - 0.11-2
libjson-script - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
liblua - 5.1.5-1
libncurses - 5.9-1
libnl-tiny - 0.1-3
libow - 2.9p5-1
libpthread - 0.9.33.2-1
librpc - 0.9.32-rc2-0a2179bbc0844928f2a0ec01dba93d9b5d6d41a7
librt - 0.9.33.2-1
libubox - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libubus-lua - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libuci - 2014-04-11.1-1
libuci-lua - 2014-04-11.1-1
libusb-1.0 - 1.0.9-1
libusb-compat - 0.1.4-1
libxtables - 1.4.21-1
lua - 5.1.5-1
luci - svn-r10467-1
luci-app-firewall - svn-r10467-1
luci-base - svn-r10467-1
luci-lib-nixio - svn-r10467-1
luci-mod-admin-full - svn-r10467-1
luci-proto-ppp - svn-r10467-1
luci-theme-bootstrap - svn-r10467-1
mc - 4.8.10-1
mtd - 20
netifd - 2014-08-07-99cfef35370b274352934c2f85a9de83ac537036
nvram - 9
odhcp6c - 2014-07-21-67b311ab81736b35858664219d345844ab08fcc7
odhcpd - 2014-08-07.1-98b41e5b07b28b438fb0be45ba294a932f4c849b
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-7
owfs - 2.9p5-1
owhttpd - 2.9p5-1
owserver - 2.9p5-1
owshell - 2.9p5-1
ppp - 2.4.6-1
ppp-mod-pppoe - 2.4.6-1
procd - 2014-07-30-35e01a9601292b2f609e65c2ddb3990cba8f378e
swconfig - 10
terminfo - 5.9-1
ubox - 2014-05-30-c3d4118eee505f41c4d20a87f326479530837569
ubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
ubusd - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
uci - 2014-04-11.1-1
uhttpd - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
uhttpd-mod-ubus - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
wpad-mini - 2014-06-03-1
zlib - 1.2.8-1

aktualny wynik dmesg
[    0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41989) ) #1 Fri Aug 8 01:10:15 CEST 2014
[    0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300)
[    0.000000] bcm47xx: using ssb bus
[    0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00
[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[    0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[    0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
[    0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
[    0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
[    0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
[    0.000000] ssb: chipcommon status is 0x0
[    0.000000] ssb: Initializing MIPS core...
[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[    0.000000] ssb: set_irq: core 0x0806, irq 5 => 5
[    0.000000] ssb: set_irq: core 0x0808, irq 6 => 2
[    0.000000] ssb: set_irq: core 0x0804, irq 2 => 6
[    0.000000] ssb: after irq reconfiguration
[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4  5* 6  D  I
[    0.000000] ssb: core 0x0808, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x0804, irq : 2(S)  3  4  5  6* D  I
[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x0807, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x080b, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
[    0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[    0.000000] MIPS: machine is Asus WL500W
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802e6b80, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 28936k/32768k available (2453k kernel code, 3832k reserved, 597k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.070000] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.110000] bio: create slab <bio-0> at 0
[    0.120000] Switching to clocksource MIPS
[    0.130000] ssb: PCIcore in host mode found
[    0.430000] PCI host bridge to bus 0000:00
[    0.430000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[    0.430000] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
[    0.430000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.430000] pci 0000:00:00.0: [14e4:4704] type 00 class 0x060000
[    0.430000] ssb: PCI: Fixing up bridge 0000:00:00.0
[    0.430000] pci 0000:00:00.0: setting latency timer to 64
[    0.430000] ssb: PCI: Fixing up device 0000:00:00.0
[    0.430000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[    0.430000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
[    0.430000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
[    0.430000] pci 0000:00:02.0: [14e4:4329] type 00 class 0x028000
[    0.430000] pci 0000:00:02.0: reg 10: [mem 0x00000000-0x00003fff]
[    0.430000] pci 0000:00:03.0: [1106:3038] type 00 class 0x0c0300
[    0.430000] pci 0000:00:03.0: reg 20: [io  0xfce0-0xfcff]
[    0.430000] pci 0000:00:03.0: supports D1 D2
[    0.430000] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci 0000:00:03.1: [1106:3038] type 00 class 0x0c0300
[    0.440000] pci 0000:00:03.1: reg 20: [io  0xfce0-0xfcff]
[    0.440000] pci 0000:00:03.1: supports D1 D2
[    0.440000] pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci 0000:00:03.2: [1106:3104] type 00 class 0x0c0320
[    0.440000] pci 0000:00:03.2: reg 10: [mem 0x00000000-0x000000ff]
[    0.440000] pci 0000:00:03.2: supports D1 D2
[    0.440000] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.440000] pci 0000:00:02.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[    0.440000] pci 0000:00:03.2: BAR 0: assigned [mem 0x40004000-0x400040ff]
[    0.440000] pci 0000:00:03.0: BAR 4: assigned [io  0x0400-0x041f]
[    0.440000] pci 0000:00:03.1: BAR 4: assigned [io  0x0420-0x043f]
[    0.450000] PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
[    0.450000] ssb: PCI: Fixing up device 0000:00:02.0
[    0.450000] b43-pci-bridge 0000:00:02.0: setting latency timer to 64
[    0.490000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[    0.490000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x12, vendor 0x4243)
[    0.490000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0B, vendor 0x4243)
[    0.490000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x02, vendor 0x4243)
[    0.490000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
[    0.490000] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[    0.530000] ssb: chipcommon status is 0x0
[    0.530000] ssb: SPROM offset is 0x1000
[    0.540000] ssb: SPROM revision 4 detected
[    0.580000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
[    0.580000] NET: Registered protocol family 2
[    0.580000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.580000] TCP: Hash tables configured (established 512 bind 512)
[    0.590000] TCP: reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.590000] PCI: CLS 0 bytes, default 16
[    0.600000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.600000] io scheduler deadline registered (default)
[    0.600000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
[    0.990000] console [ttyS0] enabled
[    1.020000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
[    1.030000] physmap platform flash device: 02000001 at 1c000000
[    1.040000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001301
[    1.050000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    1.050000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    1.050000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    1.050000] Amd/Fujitsu Extended Query Table at 0x0040
[    1.050000]   Amd/Fujitsu Extended Query version 1.3.
[    1.060000] number of CFI chips: 1
[    1.080000] 5 bcm47xxpart partitions found on MTD device physmap-flash.0
[    1.090000] Creating 5 MTD partitions on "physmap-flash.0":
[    1.090000] 0x000000000000-0x000000040000 : "boot"
[    1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[    1.110000] 0x00000004001c-0x0000001bd000 : "linux"
[    1.120000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.140000] 0x0000001bd000-0x0000007f0000 : "rootfs"
[    1.140000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.160000] mtd: device 3 (rootfs) set to be root filesystem
[    1.160000] mtd: partition "rootfs_data" created automatically, ofs=0x400000, len=0x3f0000
[    1.170000] 0x000000400000-0x0000007f0000 : "rootfs_data"
[    1.180000] 0x0000007f0000-0x000000800000 : "nvram"
[    1.210000] libphy: Fixed MDIO Bus: probed
[    1.210000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[    1.220000] GPIO_WDT: failed to register misc device
[    1.230000] TCP: cubic registered
[    1.230000] NET: Registered protocol family 17
[    1.240000] Bridge firewalling registered
[    1.240000] 8021q: 802.1Q VLAN Support v1.8
[    1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.270000] Freeing unused kernel memory: 208K (802fc000 - 80330000)
[    5.000000] pps_core: LinuxPPS API ver. 1 registered
[    5.000000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    5.020000] PTP clock support registered
[    5.030000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[    5.040000] libphy: b44_eth_mii: probed
[    5.120000] b53_common: found switch: BCM5325, rev 0
[    5.130000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e)
[    5.140000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1b:fc:bf:f1:7f
[    5.150000] libphy: b44_eth_mii: probed
[    5.150000] b44 ssb0:1: could not find PHY at 4, use fixed one
[    5.160000] b44 ssb0:1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00)
[    5.170000] b44 ssb0:1 eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:90:4c:a1:00:2d
[    5.180000] bgmac: Broadcom 47xx GBit MAC driver loaded
[    5.970000] b44 ssb0:0 eth0: Link is down
[    6.980000] b44 ssb0:0 eth0: Link is down
[    7.130000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[    7.130000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   11.870000] jffs2: notice: (253) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 13 of xref (0 dead, 5 orphan) found.
[   12.930000] usbcore: registered new interface driver usbfs
[   12.940000] usbcore: registered new interface driver hub
[   12.950000] usbcore: registered new device driver usb
[   13.150000] SCSI subsystem initialized
[   13.170000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   13.180000] ehci-platform: EHCI generic platform driver
[   13.190000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   13.200000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[   13.210000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 1
[   13.220000] ohci-platform ohci-platform.0: irq 2, io mem 0x18003000
[   13.280000] hub 1-0:1.0: USB hub found
[   13.290000] hub 1-0:1.0: 2 ports detected
[   13.310000] usbcore: registered new interface driver usb-storage
[   13.610000] b44 ssb0:0 eth0: powering down PHY
[   14.280000] b44 ssb0:0 eth0: Link is down
[   19.080000] NET: Registered protocol family 10
[   19.130000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[   19.150000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   19.180000] fuse init (API version 7.22)
[   19.200000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   19.210000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   19.220000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   19.280000] usbcore: registered new interface driver usblp
[   19.300000] Driver for 1-wire Dallas network protocol.
[   19.350000] xt_time: kernel timezone is -0000
[   19.410000] cfg80211: Calling CRDA to update world regulatory domain
[   19.410000] cfg80211: World regulatory domain updated:
[   19.420000] cfg80211:  DFS Master region: unset
[   19.420000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   19.430000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   19.440000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   19.450000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   19.460000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   19.470000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   19.470000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   19.480000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   19.490000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   19.510000] usbcore: registered new interface driver DS9490R
[   19.610000] PPP generic driver version 2.4.2
[   19.630000] NET: Registered protocol family 24
[   19.720000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[   19.790000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[   19.800000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2055, Revision 4, Version 0
[   19.890000] Broadcom 43xx driver loaded [ Features: PNL ]
[   20.070000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
[   20.080000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   25.780000] b44 ssb0:0 eth0: Link is down
[   25.780000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.780000] b44 ssb0:0 eth0: Link is down
[   27.590000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[   27.590000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   27.610000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   32.920000] b44 ssb0:0 eth0: powering down PHY
[   32.950000] b44 ssb0:0 eth0: Link is down
[   32.950000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   32.970000] device eth0 entered promiscuous mode
[   32.970000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   33.060000] b44 ssb0:1 eth1: Link is down
[   33.070000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   33.950000] b44 ssb0:0 eth0: Link is down
[   34.070000] b44 ssb0:1 eth1: Link is down
[   34.600000] br-lan: port 1(eth0) entered forwarding state
[   34.600000] br-lan: port 1(eth0) entered forwarding state
[   34.610000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.630000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   34.660000] b44 ssb0:1 eth1: Link is up at 100 Mbps, full duplex
[   34.660000] b44 ssb0:1 eth1: Flow control is off for TX and off for RX
[   34.690000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   36.600000] br-lan: port 1(eth0) entered forwarding state
[ 1143.830000] uhci_hcd: USB Universal Host Controller Interface driver
[ 1143.840000] PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
[ 1143.850000] ssb: PCI: Fixing up device 0000:00:03.0
[ 1143.850000] uhci_hcd 0000:00:03.0: UHCI Host Controller
[ 1143.860000] uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 1143.860000] uhci_hcd 0000:00:03.0: irq 6, io base 0x00000400
[ 1143.880000] hub 2-0:1.0: USB hub found
[ 1143.880000] hub 2-0:1.0: 2 ports detected
[ 1143.890000] PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
[ 1143.890000] ssb: PCI: Fixing up device 0000:00:03.1
[ 1143.900000] uhci_hcd 0000:00:03.1: UHCI Host Controller
[ 1143.900000] uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 1143.910000] uhci_hcd 0000:00:03.1: irq 6, io base 0x00000420
[ 1143.930000] hub 3-0:1.0: USB hub found
[ 1143.930000] hub 3-0:1.0: 2 ports detected

widze żę USB sie pojawiło ale w /dev nie mam ttyUSB i w /sys/devices te nie ma nic z USB

kiedy daję komendę owfs -uall to wyświetla że owfs.c:(92) No mount point specyfied ale przeciez w /dev nie ma odpowiedniego ttyUSB?

Co dalej z tym zrobić?

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,698

Odp: 1wire DS9490R jak uruchomić?

Dla ds2490 nie będziesz miał portu szeregowego. Przeczytaj http://eko.one.pl/?p=openwrt-temperatura

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

Przesytałem ale to nie jest to czego szukam. Chciałbym uruchomić owfs i z tym sobie nie radzę.

Aktualnie USB na pewno pracuje bo zamontowałem dysk czyli kontroler jest ok, ale nie mogę uruchomić DS2490.

aktualnie zainstalowane pakiety
base-files - 155-r42056
block-mount - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
busybox - 1.22.1-2
digitemp-usb - 3.6.0-5
dnsmasq - 2.71-3
dropbear - 2014.63-1
firewall - 2014-07-19
fstools - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
fuse-utils - 2.9.0-2
glib2 - 2.41.1-2
hostapd-common - 2014-06-03-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iw - 3.15-1
iwinfo - 50
jshn - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.10.49-1-5d0d3deed34436ecea1e7580c1aae878
kmod-b43 - 3.10.49+2014-05-22-1
kmod-b43legacy - 3.10.49+2014-05-22-1
kmod-b44 - 3.10.49-1
kmod-bgmac - 3.10.49-1
kmod-cfg80211 - 3.10.49+2014-05-22-1
kmod-crypto-aes - 3.10.49-1
kmod-crypto-arc4 - 3.10.49-1
kmod-crypto-core - 3.10.49-1
kmod-crypto-hash - 3.10.49-1
kmod-fs-ext4 - 3.10.49-1
kmod-fs-vfat - 3.10.49-1
kmod-fuse - 3.10.49-1
kmod-gpio-button-hotplug - 3.10.49-1
kmod-hwmon-core - 3.10.49-1
kmod-ip6tables - 3.10.49-1
kmod-ipt-conntrack - 3.10.49-1
kmod-ipt-core - 3.10.49-1
kmod-ipt-nat - 3.10.49-1
kmod-ipt-nathelper - 3.10.49-1
kmod-ipv6 - 3.10.49-1
kmod-leds-gpio - 3.10.49-1
kmod-ledtrig-default-on - 3.10.49-1
kmod-ledtrig-netdev - 3.10.49-1
kmod-ledtrig-timer - 3.10.49-1
kmod-lib-crc-ccitt - 3.10.49-1
kmod-lib-crc16 - 3.10.49-1
kmod-mac80211 - 3.10.49+2014-05-22-1
kmod-mii - 3.10.49-1
kmod-nls-base - 3.10.49-1
kmod-nls-cp437 - 3.10.49-1
kmod-nls-iso8859-1 - 3.10.49-1
kmod-ppp - 3.10.49-1
kmod-pppoe - 3.10.49-1
kmod-pppox - 3.10.49-1
kmod-pps - 3.10.49-1
kmod-ptp - 3.10.49-1
kmod-scsi-core - 3.10.49-1
kmod-slhc - 3.10.49-1
kmod-tg3 - 3.10.49-1
kmod-usb-brcm47xx - 3.10.49-1
kmod-usb-core - 3.10.49-1
kmod-usb-ohci - 3.10.49-1
kmod-usb-printer - 3.10.49-1
kmod-usb-storage - 3.10.49-1
kmod-usb-uhci - 3.10.49-1
kmod-usb2 - 3.10.49-1
kmod-w1 - 3.10.49-1
kmod-w1-master-ds2490 - 3.10.49-1
libattr - 20140610-1
libblobmsg-json - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libc - 0.9.33.2-1
libffi - 3.0.13-1
libfuse - 2.9.0-2
libgcc - 4.8-linaro-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 50
libiwinfo-lua - 50
libjson-c - 0.11-2
libjson-script - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
liblua - 5.1.5-1
libncurses - 5.9-1
libnl-tiny - 0.1-3
libow - 2.9p5-1
libpthread - 0.9.33.2-1
librpc - 0.9.32-rc2-0a2179bbc0844928f2a0ec01dba93d9b5d6d41a7
librt - 0.9.33.2-1
libubox - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libubus-lua - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libuci - 2014-04-11.1-1
libuci-lua - 2014-04-11.1-1
libusb-1.0 - 1.0.9-1
libusb-compat - 0.1.4-1
libxtables - 1.4.21-1
lua - 5.1.5-1
luci - svn-r10467-1
luci-app-firewall - svn-r10467-1
luci-base - svn-r10467-1
luci-lib-nixio - svn-r10467-1
luci-mod-admin-full - svn-r10467-1
luci-proto-ppp - svn-r10467-1
luci-theme-bootstrap - svn-r10467-1
mc - 4.8.10-1
mtd - 20
netifd - 2014-08-07-99cfef35370b274352934c2f85a9de83ac537036
nvram - 9
odhcp6c - 2014-07-21-67b311ab81736b35858664219d345844ab08fcc7
odhcpd - 2014-08-07.1-98b41e5b07b28b438fb0be45ba294a932f4c849b
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-7
owfs - 2.9p5-1
owhttpd - 2.9p5-1
owserver - 2.9p5-1
owshell - 2.9p5-1
ppp - 2.4.6-1
ppp-mod-pppoe - 2.4.6-1
procd - 2014-07-30-35e01a9601292b2f609e65c2ddb3990cba8f378e
swconfig - 10
terminfo - 5.9-1
ubox - 2014-05-30-c3d4118eee505f41c4d20a87f326479530837569
ubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
ubusd - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
uci - 2014-04-11.1-1
uhttpd - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
uhttpd-mod-ubus - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
wpad-mini - 2014-06-03-1
zlib - 1.2.8-1

dmesg
[    0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41989) ) #1 Fri Aug 8 01:10:15 CEST 2014
[    0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300)
[    0.000000] bcm47xx: using ssb bus
[    0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00
[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[    0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[    0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
[    0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
[    0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
[    0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
[    0.000000] ssb: chipcommon status is 0x0
[    0.000000] ssb: Initializing MIPS core...
[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[    0.000000] ssb: set_irq: core 0x0806, irq 5 => 5
[    0.000000] ssb: set_irq: core 0x0808, irq 6 => 2
[    0.000000] ssb: set_irq: core 0x0804, irq 2 => 6
[    0.000000] ssb: after irq reconfiguration
[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4  5* 6  D  I
[    0.000000] ssb: core 0x0808, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x0804, irq : 2(S)  3  4  5  6* D  I
[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x0807, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x080b, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
[    0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[    0.000000] MIPS: machine is Asus WL500W
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802e6b80, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 28936k/32768k available (2453k kernel code, 3832k reserved, 597k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.070000] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.110000] bio: create slab <bio-0> at 0
[    0.120000] Switching to clocksource MIPS
[    0.130000] ssb: PCIcore in host mode found
[    0.430000] PCI host bridge to bus 0000:00
[    0.430000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[    0.430000] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
[    0.430000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.430000] pci 0000:00:00.0: [14e4:4704] type 00 class 0x060000
[    0.430000] ssb: PCI: Fixing up bridge 0000:00:00.0
[    0.430000] pci 0000:00:00.0: setting latency timer to 64
[    0.430000] ssb: PCI: Fixing up device 0000:00:00.0
[    0.430000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[    0.430000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
[    0.430000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
[    0.430000] pci 0000:00:02.0: [14e4:4329] type 00 class 0x028000
[    0.430000] pci 0000:00:02.0: reg 10: [mem 0x00000000-0x00003fff]
[    0.430000] pci 0000:00:03.0: [1106:3038] type 00 class 0x0c0300
[    0.430000] pci 0000:00:03.0: reg 20: [io  0xfce0-0xfcff]
[    0.430000] pci 0000:00:03.0: supports D1 D2
[    0.430000] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci 0000:00:03.1: [1106:3038] type 00 class 0x0c0300
[    0.440000] pci 0000:00:03.1: reg 20: [io  0xfce0-0xfcff]
[    0.440000] pci 0000:00:03.1: supports D1 D2
[    0.440000] pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci 0000:00:03.2: [1106:3104] type 00 class 0x0c0320
[    0.440000] pci 0000:00:03.2: reg 10: [mem 0x00000000-0x000000ff]
[    0.440000] pci 0000:00:03.2: supports D1 D2
[    0.440000] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.440000] pci 0000:00:02.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[    0.440000] pci 0000:00:03.2: BAR 0: assigned [mem 0x40004000-0x400040ff]
[    0.440000] pci 0000:00:03.0: BAR 4: assigned [io  0x0400-0x041f]
[    0.440000] pci 0000:00:03.1: BAR 4: assigned [io  0x0420-0x043f]
[    0.450000] PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
[    0.450000] ssb: PCI: Fixing up device 0000:00:02.0
[    0.450000] b43-pci-bridge 0000:00:02.0: setting latency timer to 64
[    0.490000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[    0.490000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x12, vendor 0x4243)
[    0.490000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0B, vendor 0x4243)
[    0.490000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x02, vendor 0x4243)
[    0.490000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
[    0.490000] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[    0.530000] ssb: chipcommon status is 0x0
[    0.530000] ssb: SPROM offset is 0x1000
[    0.540000] ssb: SPROM revision 4 detected
[    0.580000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
[    0.580000] NET: Registered protocol family 2
[    0.580000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.580000] TCP: Hash tables configured (established 512 bind 512)
[    0.590000] TCP: reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.590000] PCI: CLS 0 bytes, default 16
[    0.600000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.600000] io scheduler deadline registered (default)
[    0.600000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
[    0.990000] console [ttyS0] enabled
[    1.020000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
[    1.030000] physmap platform flash device: 02000001 at 1c000000
[    1.040000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001301
[    1.050000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    1.050000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    1.050000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    1.050000] Amd/Fujitsu Extended Query Table at 0x0040
[    1.050000]   Amd/Fujitsu Extended Query version 1.3.
[    1.060000] number of CFI chips: 1
[    1.080000] 5 bcm47xxpart partitions found on MTD device physmap-flash.0
[    1.090000] Creating 5 MTD partitions on "physmap-flash.0":
[    1.090000] 0x000000000000-0x000000040000 : "boot"
[    1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[    1.110000] 0x00000004001c-0x0000001bd000 : "linux"
[    1.120000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.140000] 0x0000001bd000-0x0000007f0000 : "rootfs"
[    1.140000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.160000] mtd: device 3 (rootfs) set to be root filesystem
[    1.160000] mtd: partition "rootfs_data" created automatically, ofs=0x400000, len=0x3f0000
[    1.170000] 0x000000400000-0x0000007f0000 : "rootfs_data"
[    1.180000] 0x0000007f0000-0x000000800000 : "nvram"
[    1.210000] libphy: Fixed MDIO Bus: probed
[    1.210000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[    1.220000] GPIO_WDT: failed to register misc device
[    1.230000] TCP: cubic registered
[    1.230000] NET: Registered protocol family 17
[    1.240000] Bridge firewalling registered
[    1.240000] 8021q: 802.1Q VLAN Support v1.8
[    1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.270000] Freeing unused kernel memory: 208K (802fc000 - 80330000)
[    5.000000] pps_core: LinuxPPS API ver. 1 registered
[    5.000000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    5.020000] PTP clock support registered
[    5.030000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[    5.040000] libphy: b44_eth_mii: probed
[    5.120000] b53_common: found switch: BCM5325, rev 0
[    5.130000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e)
[    5.140000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1b:fc:bf:f1:7f
[    5.150000] libphy: b44_eth_mii: probed
[    5.150000] b44 ssb0:1: could not find PHY at 4, use fixed one
[    5.160000] b44 ssb0:1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00)
[    5.170000] b44 ssb0:1 eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:90:4c:a1:00:2d
[    5.180000] bgmac: Broadcom 47xx GBit MAC driver loaded
[    5.970000] b44 ssb0:0 eth0: Link is down
[    6.980000] b44 ssb0:0 eth0: Link is down
[    7.130000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[    7.130000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   11.890000] jffs2: notice: (253) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found.
[   12.980000] usbcore: registered new interface driver usbfs
[   12.990000] usbcore: registered new interface driver hub
[   12.990000] usbcore: registered new device driver usb
[   13.200000] SCSI subsystem initialized
[   13.220000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   13.230000] ehci-platform: EHCI generic platform driver
[   13.240000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   13.250000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[   13.260000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 1
[   13.260000] ohci-platform ohci-platform.0: irq 2, io mem 0x18003000
[   13.330000] hub 1-0:1.0: USB hub found
[   13.340000] hub 1-0:1.0: 2 ports detected
[   13.350000] uhci_hcd: USB Universal Host Controller Interface driver
[   13.360000] PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
[   13.360000] ssb: PCI: Fixing up device 0000:00:03.0
[   13.370000] uhci_hcd 0000:00:03.0: UHCI Host Controller
[   13.370000] uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[   13.380000] uhci_hcd 0000:00:03.0: irq 6, io base 0x00000400
[   13.390000] hub 2-0:1.0: USB hub found
[   13.400000] hub 2-0:1.0: 2 ports detected
[   13.400000] PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
[   13.410000] ssb: PCI: Fixing up device 0000:00:03.1
[   13.410000] uhci_hcd 0000:00:03.1: UHCI Host Controller
[   13.420000] uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[   13.420000] uhci_hcd 0000:00:03.1: irq 6, io base 0x00000420
[   13.440000] hub 3-0:1.0: USB hub found
[   13.440000] hub 3-0:1.0: 2 ports detected
[   13.460000] usbcore: registered new interface driver usb-storage
[   13.760000] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[   13.770000] b44 ssb0:0 eth0: powering down PHY
[   14.320000] b44 ssb0:0 eth0: Link is down
[   14.440000] usb-storage 2-1:1.0: USB Mass Storage device detected
[   14.460000] scsi0 : usb-storage 2-1:1.0
[   15.680000] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer           7.01 PQ: 0 ANSI: 0 CCS
[   15.750000] sd 0:0:0:0: [sda] 7862911 512-byte logical blocks: (4.02 GB/3.74 GiB)
[   15.760000] sd 0:0:0:0: [sda] Write Protect is off
[   15.760000] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
[   15.770000] sd 0:0:0:0: [sda] No Caching mode page found
[   15.770000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   15.860000] sd 0:0:0:0: [sda] No Caching mode page found
[   15.870000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   15.940000]  sda: sda1
[   15.990000] sd 0:0:0:0: [sda] No Caching mode page found
[   15.990000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   16.000000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   19.990000] NET: Registered protocol family 10
[   20.040000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[   20.070000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   20.100000] fuse init (API version 7.22)
[   20.110000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   20.120000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   20.140000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.200000] usbcore: registered new interface driver usblp
[   20.220000] Driver for 1-wire Dallas network protocol.
[   20.280000] xt_time: kernel timezone is -0000
[   20.340000] cfg80211: Calling CRDA to update world regulatory domain
[   20.340000] cfg80211: World regulatory domain updated:
[   20.350000] cfg80211:  DFS Master region: unset
[   20.350000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   20.360000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.370000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.380000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   20.390000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   20.400000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.410000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.410000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   20.420000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   20.450000] usbcore: registered new interface driver DS9490R
[   20.590000] PPP generic driver version 2.4.2
[   20.600000] NET: Registered protocol family 24
[   20.650000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[   20.720000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[   20.730000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2055, Revision 4, Version 0
[   20.760000] Broadcom 43xx driver loaded [ Features: PNL ]
[   20.950000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   20.950000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
[   26.650000] b44 ssb0:0 eth0: Link is down
[   26.660000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   27.660000] b44 ssb0:0 eth0: Link is down
[   27.850000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[   27.850000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   27.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   33.860000] b44 ssb0:0 eth0: powering down PHY
[   33.890000] b44 ssb0:0 eth0: Link is down
[   33.890000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   33.920000] device eth0 entered promiscuous mode
[   33.920000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   34.000000] b44 ssb0:1 eth1: Link is down
[   34.010000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   34.890000] b44 ssb0:0 eth0: Link is down
[   35.010000] b44 ssb0:1 eth1: Link is down
[   35.860000] br-lan: port 1(eth0) entered forwarding state
[   35.860000] br-lan: port 1(eth0) entered forwarding state
[   35.870000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   35.900000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   35.900000] b44 ssb0:1 eth1: Link is up at 100 Mbps, full duplex
[   35.910000] b44 ssb0:1 eth1: Flow control is off for TX and off for RX
[   35.950000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   37.860000] br-lan: port 1(eth0) entered forwarding state
[ 1405.860000] usb 2-2: new full-speed USB device number 4 using uhci_hcd
[ 1406.080000] CPU 0 Unable to handle kernel paging request at virtual address 000003f0, epc == 80e40680, ra == 80e40d74
[ 1406.090000] Oops[#1]:
[ 1406.090000] CPU: 0 PID: 1122 Comm: w1_bus_master1 Not tainted 3.10.49 #1
[ 1406.090000] task: 81b6d988 ti: 81844000 task.ti: 81844000
[ 1406.090000] $ 0   : 00000000 1000fc00 00000000 0000000e
[ 1406.090000] $ 4   : 000003e8 81845e10 00000001 ffff00fe
[ 1406.090000] $ 8   : 40200001 00040405 00005320 00000100
[ 1406.090000] $12   : 0000001f 818a3e88 00000000 802c618c
[ 1406.090000] $16   : 000003e8 80360000 000000f0 81bb0c74
[ 1406.090000] $20   : 00000040 80de0770 00000001 00000003
[ 1406.090000] $24   : 00000000 80247cf8                 
[ 1406.090000] $28   : 81844000 81845d90 00000000 80e40d74
[ 1406.090000] Hi    : 00000000
[ 1406.090000] Lo    : 00000000
[ 1406.090000] epc   : 80e40680 0x80e40680
[ 1406.090000]     Not tainted
[ 1406.090000] ra    : 80e40d74 0x80e40d74
[ 1406.090000] Status: 1000fc03    KERNEL EXL IE
[ 1406.090000] Cause : 00800008
[ 1406.090000] BadVA : 000003f0
[ 1406.090000] PrId  : 00029006 (Broadcom BMIPS3300)
[ 1406.090000] Modules linked in: pppoe ppp_async iptable_nat b43legacy b43 pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv4 mac80211 ipt_MASQUERADE ds2490 cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT wire usblp slhc nf_nat_irc nf_nat_ftp nf_nat nf_defrag_ipv4 nf_conntrack_irc nf_conntrack_ftp iptable_raw iptable_mangle iptable_filter ipt_REJECT ip_tables crc_ccitt compat fuse ip6t_REJECT ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables nf_conntrack_ipv6 nf_conntrack nf_defrag_ipv6 vfat fat nls_iso8859_1 nls_cp437 ipv6 arc4 crypto_blkcipher usb_storage uhci_hcd ohci_hcd ehci_platform ehci_hcd sd_mod scsi_mod ext4 crc16 jbd2 mbcache usbcore nls_base usb_common ssb_hcd bcma_hcd crypto_hash leds_gpio gpio_button_hotplug tg3 hwmon bgmac b44 ptp pps_core
[ 1406.090000] Process w1_bus_master1 (pid: 1122, threadinfo=81844000, task=81b6d988, tls=00000000)
[ 1406.090000] Stack : 00000000 00000000 00000000 8152e800 81845e00 80e40b04 80de0770 00000001
[ 1406.090000]       00000003 80e40118 40200001 00040405 00005320 00000100 00000053 000000f0
[ 1406.090000]       00000000 00000000 000003e8 80360000 000003e8 80360000 000000f0 80e40d74
[ 1406.090000]       00000000 00000000 000003e8 81b6d988 40200001 00040405 00005320 00000100
[ 1406.090000]       1000fc00 00000000 81bb0c00 80de22cc 802e5f10 80de1f5c 1000fc00 00000000
[ 1406.090000]       ...
[ 1406.090000] Call Trace:
[ 1406.090000] [<80e40680>] 0x80e40680
[ 1406.090000]
[ 1406.090000]
[ 1406.090000] Code: afb00050  afbf005c  00808021 <8c840008> 00a01021  afa00048  8e05001c  8c830000  3c12c000
[ 1406.320000] ---[ end trace 149ab3670c7361f3 ]---
[ 1406.500000] usb 2-2: USB disconnect, device number 4
[ 1406.500000] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 800df5ac, ra == 80045b2c
[ 1406.510000] Oops[#2]:
[ 1406.510000] CPU: 0 PID: 269 Comm: khubd Tainted: G      D      3.10.49 #1
[ 1406.510000] task: 81bb4968 ti: 80c4e000 task.ti: 80c4e000
[ 1406.510000] $ 0   : 00000000 1000fc01 00000000 00000001
[ 1406.510000] $ 4   : 81b6d988 ffffffe8 8152e800 ffffffff
[ 1406.510000] $ 8   : 00000008 00000001 0000000e 0000000e
[ 1406.510000] $12   : 00000000 77f1e448 00000000 2c746365
[ 1406.510000] $16   : 81b6d988 81b6d988 00000100 80e41410
[ 1406.510000] $20   : 00000000 00000000 817af800 80d75bb8
[ 1406.510000] $24   : 00000003 80145abc                 
[ 1406.510000] $28   : 80c4e000 80c4fc98 00000000 80045b2c
[ 1406.510000] Hi    : 00000000
[ 1406.510000] Lo    : 00000084
[ 1406.510000] epc   : 800df5ac exit_creds+0x14/0x88
[ 1406.510000]     Tainted: G      D     
[ 1406.510000] ra    : 80045b2c __put_task_struct+0x60/0xa4
[ 1406.510000] Status: 1000fc03    KERNEL EXL IE
[ 1406.510000] Cause : 00800008
[ 1406.510000] BadVA : 00000000
[ 1406.510000] PrId  : 00029006 (Broadcom BMIPS3300)
[ 1406.510000] Modules linked in: pppoe ppp_async iptable_nat b43legacy b43 pppox ppp_generic nf_nat_ipv4 nf_conntrack_ipv4 mac80211 ipt_MASQUERADE ds2490 cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_CT wire usblp slhc nf_nat_irc nf_nat_ftp nf_nat nf_defrag_ipv4 nf_conntrack_irc nf_conntrack_ftp iptable_raw iptable_mangle iptable_filter ipt_REJECT ip_tables crc_ccitt compat fuse ip6t_REJECT ip6table_raw ip6table_mangle ip6table_filter ip6_tables x_tables nf_conntrack_ipv6 nf_conntrack nf_defrag_ipv6 vfat fat nls_iso8859_1 nls_cp437 ipv6 arc4 crypto_blkcipher usb_storage uhci_hcd ohci_hcd ehci_platform ehci_hcd sd_mod scsi_mod ext4 crc16 jbd2 mbcache usbcore nls_base usb_common ssb_hcd bcma_hcd crypto_hash leds_gpio gpio_button_hotplug tg3 hwmon bgmac b44 ptp pps_core
[ 1406.510000] Process khubd (pid: 269, threadinfo=80c4e000, task=81bb4968, tls=00000000)
[ 1406.510000] Stack : 00000000 80209498 00000001 80208928 81b6d988 80045b2c 80e05148 802af958
[ 1406.510000]       802af968 801befbc 81b6d990 8014a154 8186a908 802af958 802af968 801befbc
[ 1406.510000]       81bb0c00 80de0000 80e40000 80de1a9c 817af800 00000000 00000000 80c6a7c8
[ 1406.510000]       80c4fd50 80c4fd18 81ad7dec ffffffff 00000002 8152e800 81af38a0 80e40000
[ 1406.510000]       80e41410 80e4006c 80c4fd1c 80209b94 81af38a0 817af800 81af38a0 817af800
[ 1406.510000]       ...
[ 1406.510000] Call Trace:
[ 1406.510000] [<800df5ac>] exit_creds+0x14/0x88
[ 1406.510000] [<80045b2c>] __put_task_struct+0x60/0xa4
[ 1406.510000] [<8014a154>] kthread_stop+0x94/0xb0
[ 1406.510000] [<80de1a9c>] __w1_remove_master_device+0x28/0x15c [wire]
[ 1406.510000] [<80e4006c>] 0x80e4006c
[ 1406.510000]
[ 1406.510000]
[ 1406.510000] Code: afbf0014  8c8201a4  00808021 <8c420000> 8c8401a0  ae0001a0  c0830000  2462ffff  e0820000
[ 1406.770000] ---[ end trace 149ab3670c7361f4 ]---

a owfs -u /mnt/sda1 nic nie wykonuje i czeka. Jak zainstalowałem digitempa to znalazł DS2490 ale nie o to mi chodzi. digitemp nie ma mozliwosci sterowania DS2408

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,698

Odp: 1wire DS9490R jak uruchomić?

Ślicznie wyłożył Ci się kernel.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

smile to co jeszcze raz wgranie openwrt i i instalacja pakietów?
Jakie pakiety wybrać i w jakiej kolejności jeśli ma to znaczenie?

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,698

Odp: 1wire DS9490R jak uruchomić?

Błąd sugeruje brak pamięci, ale może to wynikać z błędu w samym owfs.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

to spróbuje jeszcze raz zainstalować openwrt i tylko niezbędne pakiety. A mozę wyrzucić luci?
chciałbym wgrać następujace pakiety

kmod-usb-brcm47xx - 3.10.49-1
kmod-usb-core - 3.10.49-1
kmod-usb-ohci - 3.10.49-1
kmod-usb-storage - 3.10.49-1
kmod-usb-uhci - 3.10.49-1
kmod-usb2 - 3.10.49-1
kmod-w1 - 3.10.49-1
kmod-w1-master-ds2490 - 3.10.49-1
mc - 4.8.10-1
owfs - 2.9p5-1
owhttpd - 2.9p5-1
owserver - 2.9p5-1
owshell - 2.9p5-1

co ty na to?

10 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

to nie powinno mieć znaczenia ale jak wszyyscy wiedzą w wl500xx należy co rok dwa wymienić trzy kondensatory na płycie głównej bo diabli je biorą. ten router kupiłem na allegro i nie był serwisowany jeszcze przezemnie, może to jest problemem. Wykorzytuje linię 2-przewodową 1wire wiec moze prąda brakować smile

11 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

juz zacząłem flaschować wl-500W za pomoca http://downloads.openwrt.org/barrier_br … uashfs.trx

12 Odpowiedź przez pawkaras

  • Zarejestrowany: 2014-09-17
  • Posty: 10

Odp: 1wire DS9490R jak uruchomić?

przeinstalowałem system aktualnie jest  BARRIER BREAKER (14.07-rc3, r42056) z następującymi pakietami

base-files - 155-r42056
block-mount - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
busybox - 1.22.1-2
dnsmasq - 2.71-3
dropbear - 2014.63-1
firewall - 2014-07-19
fstools - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
fuse-utils - 2.9.0-2
glib2 - 2.41.1-2
hostapd-common - 2014-06-03-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iw - 3.15-1
iwinfo - 50
jshn - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.10.49-1-5d0d3deed34436ecea1e7580c1aae878
kmod-b43 - 3.10.49+2014-05-22-1
kmod-b43legacy - 3.10.49+2014-05-22-1
kmod-b44 - 3.10.49-1
kmod-bgmac - 3.10.49-1
kmod-cfg80211 - 3.10.49+2014-05-22-1
kmod-crypto-aes - 3.10.49-1
kmod-crypto-arc4 - 3.10.49-1
kmod-crypto-core - 3.10.49-1
kmod-crypto-hash - 3.10.49-1
kmod-fs-ext4 - 3.10.49-1
kmod-fs-vfat - 3.10.49-1
kmod-fuse - 3.10.49-1
kmod-gpio-button-hotplug - 3.10.49-1
kmod-hwmon-core - 3.10.49-1
kmod-ip6tables - 3.10.49-1
kmod-ipt-conntrack - 3.10.49-1
kmod-ipt-core - 3.10.49-1
kmod-ipt-nat - 3.10.49-1
kmod-ipt-nathelper - 3.10.49-1
kmod-ipv6 - 3.10.49-1
kmod-leds-gpio - 3.10.49-1
kmod-ledtrig-default-on - 3.10.49-1
kmod-ledtrig-netdev - 3.10.49-1
kmod-ledtrig-timer - 3.10.49-1
kmod-lib-crc-ccitt - 3.10.49-1
kmod-lib-crc16 - 3.10.49-1
kmod-mac80211 - 3.10.49+2014-05-22-1
kmod-mii - 3.10.49-1
kmod-nls-base - 3.10.49-1
kmod-nls-cp437 - 3.10.49-1
kmod-nls-iso8859-1 - 3.10.49-1
kmod-ppp - 3.10.49-1
kmod-pppoe - 3.10.49-1
kmod-pppox - 3.10.49-1
kmod-pps - 3.10.49-1
kmod-ptp - 3.10.49-1
kmod-scsi-core - 3.10.49-1
kmod-slhc - 3.10.49-1
kmod-tg3 - 3.10.49-1
kmod-usb-brcm47xx - 3.10.49-1
kmod-usb-core - 3.10.49-1
kmod-usb-ohci - 3.10.49-1
kmod-usb-storage - 3.10.49-1
kmod-usb-uhci - 3.10.49-1
kmod-usb2 - 3.10.49-1
kmod-w1 - 3.10.49-1
kmod-w1-master-ds2490 - 3.10.49-1
libattr - 20140610-1
libblobmsg-json - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libc - 0.9.33.2-1
libffi - 3.0.13-1
libfuse - 2.9.0-2
libgcc - 4.8-linaro-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 50
libiwinfo-lua - 50
libjson-c - 0.11-2
libjson-script - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
liblua - 5.1.5-1
libncurses - 5.9-1
libnl-tiny - 0.1-3
libow - 2.9p5-1
libpthread - 0.9.33.2-1
librpc - 0.9.32-rc2-0a2179bbc0844928f2a0ec01dba93d9b5d6d41a7
librt - 0.9.33.2-1
libubox - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libubus-lua - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libuci - 2014-04-11.1-1
libuci-lua - 2014-04-11.1-1
libusb-1.0 - 1.0.9-1
libusb-compat - 0.1.4-1
libxtables - 1.4.21-1
lua - 5.1.5-1
luci - svn-r10467-1
luci-app-firewall - svn-r10467-1
luci-base - svn-r10467-1
luci-lib-nixio - svn-r10467-1
luci-mod-admin-full - svn-r10467-1
luci-proto-ppp - svn-r10467-1
luci-theme-bootstrap - svn-r10467-1
mc - 4.8.10-1
mtd - 20
netifd - 2014-08-07-99cfef35370b274352934c2f85a9de83ac537036
nvram - 9
odhcp6c - 2014-07-21-67b311ab81736b35858664219d345844ab08fcc7
odhcpd - 2014-08-07.1-98b41e5b07b28b438fb0be45ba294a932f4c849b
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-7
owfs - 2.9p5-1
owhttpd - 2.9p5-1
owserver - 2.9p5-1
owshell - 2.9p5-1
ppp - 2.4.6-1
ppp-mod-pppoe - 2.4.6-1
procd - 2014-07-30-35e01a9601292b2f609e65c2ddb3990cba8f378e
swconfig - 10
terminfo - 5.9-1
ubox - 2014-05-30-c3d4118eee505f41c4d20a87f326479530837569
ubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
ubusd - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
uci - 2014-04-11.1-1
uhttpd - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
uhttpd-mod-ubus - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
wpad-mini - 2014-06-03-1
zlib - 1.2.8-1

ale w dalszym ciągu nie mogę dostać się do DS2490.

dmesg daje

[    0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300)
[    0.000000] bcm47xx: using ssb bus
[    0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00
[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[    0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
[    0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
[    0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
[    0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
[    0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
[    0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
[    0.000000] ssb: chipcommon status is 0x0
[    0.000000] ssb: Initializing MIPS core...
[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[    0.000000] ssb: set_irq: core 0x0806, irq 5 => 5
[    0.000000] ssb: set_irq: core 0x0808, irq 6 => 2
[    0.000000] ssb: set_irq: core 0x0804, irq 2 => 6
[    0.000000] ssb: after irq reconfiguration
[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4  5* 6  D  I
[    0.000000] ssb: core 0x0808, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x0804, irq : 2(S)  3  4  5  6* D  I
[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x0807, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x080b, irq : 2(S)* 3  4  5  6  D  I
[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
[    0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[    0.000000] MIPS: machine is Asus WL500W
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802e6b80, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8192 pages, LIFO batch:0
[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Memory: 28936k/32768k available (2453k kernel code, 3832k reserved, 597k data, 208k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.070000] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.110000] bio: create slab <bio-0> at 0
[    0.120000] Switching to clocksource MIPS
[    0.130000] ssb: PCIcore in host mode found
[    0.430000] PCI host bridge to bus 0000:00
[    0.430000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[    0.430000] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
[    0.430000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.430000] pci 0000:00:00.0: [14e4:4704] type 00 class 0x060000
[    0.430000] ssb: PCI: Fixing up bridge 0000:00:00.0
[    0.430000] pci 0000:00:00.0: setting latency timer to 64
[    0.430000] ssb: PCI: Fixing up device 0000:00:00.0
[    0.430000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[    0.430000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
[    0.430000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
[    0.430000] pci 0000:00:02.0: [14e4:4329] type 00 class 0x028000
[    0.430000] pci 0000:00:02.0: reg 10: [mem 0x00000000-0x00003fff]
[    0.430000] pci 0000:00:03.0: [1106:3038] type 00 class 0x0c0300
[    0.430000] pci 0000:00:03.0: reg 20: [io  0xfce0-0xfcff]
[    0.430000] pci 0000:00:03.0: supports D1 D2
[    0.430000] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci 0000:00:03.1: [1106:3038] type 00 class 0x0c0300
[    0.440000] pci 0000:00:03.1: reg 20: [io  0xfce0-0xfcff]
[    0.440000] pci 0000:00:03.1: supports D1 D2
[    0.440000] pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci 0000:00:03.2: [1106:3104] type 00 class 0x0c0320
[    0.440000] pci 0000:00:03.2: reg 10: [mem 0x00000000-0x000000ff]
[    0.440000] pci 0000:00:03.2: supports D1 D2
[    0.440000] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
[    0.440000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.440000] pci 0000:00:02.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[    0.440000] pci 0000:00:03.2: BAR 0: assigned [mem 0x40004000-0x400040ff]
[    0.440000] pci 0000:00:03.0: BAR 4: assigned [io  0x0400-0x041f]
[    0.440000] pci 0000:00:03.1: BAR 4: assigned [io  0x0420-0x043f]
[    0.450000] PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
[    0.450000] ssb: PCI: Fixing up device 0000:00:02.0
[    0.450000] b43-pci-bridge 0000:00:02.0: setting latency timer to 64
[    0.490000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[    0.490000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x12, vendor 0x4243)
[    0.490000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0B, vendor 0x4243)
[    0.490000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x02, vendor 0x4243)
[    0.490000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
[    0.490000] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[    0.530000] ssb: chipcommon status is 0x0
[    0.530000] ssb: SPROM offset is 0x1000
[    0.540000] ssb: SPROM revision 4 detected
[    0.580000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
[    0.580000] NET: Registered protocol family 2
[    0.580000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.580000] TCP: Hash tables configured (established 512 bind 512)
[    0.590000] TCP: reno registered
[    0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.590000] NET: Registered protocol family 1
[    0.590000] PCI: CLS 0 bytes, default 16
[    0.600000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.600000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] io scheduler noop registered
[    0.600000] io scheduler deadline registered (default)
[    0.600000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.640000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
[    0.990000] console [ttyS0] enabled
[    1.020000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
[    1.030000] physmap platform flash device: 02000001 at 1c000000
[    1.040000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001301
[    1.050000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    1.050000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    1.050000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    1.050000] Amd/Fujitsu Extended Query Table at 0x0040
[    1.050000]   Amd/Fujitsu Extended Query version 1.3.
[    1.060000] number of CFI chips: 1
[    1.080000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[    1.090000] Creating 6 MTD partitions on "physmap-flash.0":
[    1.090000] 0x000000000000-0x000000040000 : "boot"
[    1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[    1.110000] 0x00000004001c-0x00000004090c : "loader"
[    1.120000] 0x00000004090c-0x000000152c00 : "linux"
[    1.130000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.150000] 0x000000152c00-0x0000007f0000 : "rootfs"
[    1.150000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.170000] mtd: device 4 (rootfs) set to be root filesystem
[    1.180000] mtd: partition "rootfs_data" created automatically, ofs=0x3a0000, len=0x450000
[    1.180000] 0x0000003a0000-0x0000007f0000 : "rootfs_data"
[    1.190000] 0x0000007f0000-0x000000800000 : "nvram"
[    1.220000] libphy: Fixed MDIO Bus: probed
[    1.220000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[    1.230000] GPIO_WDT: failed to register misc device
[    1.240000] TCP: cubic registered
[    1.240000] NET: Registered protocol family 17
[    1.250000] Bridge firewalling registered
[    1.250000] 8021q: 802.1Q VLAN Support v1.8
[    1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.280000] Freeing unused kernel memory: 208K (802fc000 - 80330000)
[    5.000000] pps_core: LinuxPPS API ver. 1 registered
[    5.010000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    5.020000] PTP clock support registered
[    5.040000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[    5.050000] libphy: b44_eth_mii: probed
[    5.130000] b53_common: found switch: BCM5325, rev 0
[    5.130000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e)
[    5.140000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1b:fc:bf:f1:7f
[    5.150000] libphy: b44_eth_mii: probed
[    5.160000] b44 ssb0:1: could not find PHY at 4, use fixed one
[    5.160000] b44 ssb0:1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00)
[    5.170000] b44 ssb0:1 eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:90:4c:a1:00:2d
[    5.190000] bgmac: Broadcom 47xx GBit MAC driver loaded
[    5.980000] b44 ssb0:0 eth0: Link is down
[    6.980000] b44 ssb0:0 eth0: Link is down
[    7.130000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[    7.130000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   11.880000] jffs2: notice: (257) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found.
[   12.950000] usbcore: registered new interface driver usbfs
[   12.960000] usbcore: registered new interface driver hub
[   12.960000] usbcore: registered new device driver usb
[   13.170000] SCSI subsystem initialized
[   13.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   13.200000] ehci-platform: EHCI generic platform driver
[   13.210000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   13.220000] ohci-platform ohci-platform.0: Generic Platform OHCI Controller
[   13.220000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 1
[   13.230000] ohci-platform ohci-platform.0: irq 2, io mem 0x18003000
[   13.300000] hub 1-0:1.0: USB hub found
[   13.310000] hub 1-0:1.0: 2 ports detected
[   13.320000] uhci_hcd: USB Universal Host Controller Interface driver
[   13.330000] PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
[   13.330000] ssb: PCI: Fixing up device 0000:00:03.0
[   13.340000] uhci_hcd 0000:00:03.0: UHCI Host Controller
[   13.340000] uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[   13.350000] uhci_hcd 0000:00:03.0: irq 6, io base 0x00000400
[   13.360000] hub 2-0:1.0: USB hub found
[   13.370000] hub 2-0:1.0: 2 ports detected
[   13.370000] PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
[   13.380000] ssb: PCI: Fixing up device 0000:00:03.1
[   13.380000] uhci_hcd 0000:00:03.1: UHCI Host Controller
[   13.390000] uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[   13.390000] uhci_hcd 0000:00:03.1: irq 6, io base 0x00000420
[   13.410000] hub 3-0:1.0: USB hub found
[   13.410000] hub 3-0:1.0: 2 ports detected
[   13.430000] usbcore: registered new interface driver usb-storage
[   13.730000] usb 2-1: new full-speed USB device number 2 using uhci_hcd
[   13.750000] b44 ssb0:0 eth0: powering down PHY
[   14.290000] b44 ssb0:0 eth0: Link is down
[   14.480000] usb-storage 2-1:1.0: USB Mass Storage device detected
[   14.480000] scsi0 : usb-storage 2-1:1.0
[   15.810000] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer           7.01 PQ: 0 ANSI: 0 CCS
[   15.850000] sd 0:0:0:0: [sda] 7862911 512-byte logical blocks: (4.02 GB/3.74 GiB)
[   15.870000] sd 0:0:0:0: [sda] Write Protect is off
[   15.870000] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08
[   15.870000] sd 0:0:0:0: [sda] No Caching mode page found
[   15.880000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   15.930000] sd 0:0:0:0: [sda] No Caching mode page found
[   15.940000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   15.990000]  sda: sda1
[   16.040000] sd 0:0:0:0: [sda] No Caching mode page found
[   16.040000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   16.050000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   20.270000] NET: Registered protocol family 10
[   20.320000] nf_conntrack version 0.5.0 (455 buckets, 1820 max)
[   20.350000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   20.380000] fuse init (API version 7.22)
[   20.400000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   20.400000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   20.420000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.480000] Driver for 1-wire Dallas network protocol.
[   20.540000] xt_time: kernel timezone is -0000
[   20.600000] cfg80211: Calling CRDA to update world regulatory domain
[   20.610000] cfg80211: World regulatory domain updated:
[   20.610000] cfg80211:  DFS Master region: unset
[   20.620000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   20.630000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.640000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   20.650000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   20.650000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   20.660000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.670000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   20.680000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   20.690000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   20.700000] usbcore: registered new interface driver DS9490R
[   20.840000] PPP generic driver version 2.4.2
[   20.860000] NET: Registered protocol family 24
[   20.910000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[   20.980000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[   20.990000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2055, Revision 4, Version 0
[   21.020000] Broadcom 43xx driver loaded [ Features: PNL ]
[   21.190000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
[   21.210000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   26.990000] b44 ssb0:0 eth0: Link is down
[   26.990000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   27.990000] b44 ssb0:0 eth0: Link is down
[   28.680000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[   28.680000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   28.810000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.110000] b44 ssb0:0 eth0: powering down PHY
[   34.140000] b44 ssb0:0 eth0: Link is down
[   34.140000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.160000] device eth0 entered promiscuous mode
[   34.160000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   34.240000] b44 ssb0:1 eth1: Link is down
[   34.250000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   35.140000] b44 ssb0:0 eth0: Link is down
[   35.250000] b44 ssb0:1 eth1: Link is down
[   35.770000] br-lan: port 1(eth0) entered forwarding state
[   35.770000] br-lan: port 1(eth0) entered forwarding state
[   35.780000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   35.810000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   35.810000] b44 ssb0:1 eth1: Link is up at 100 Mbps, full duplex
[   35.820000] b44 ssb0:1 eth1: Flow control is off for TX and off for RX
[   35.850000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   37.770000] br-lan: port 1(eth0) entered forwarding state

wygląda lepiej jak ostatnio ale nadal nie jest dobrze