FAQ o OpenWrt | Sprzedam różne routery | Oddam

bhb · 2014-08-19 09:59:51

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

uci show network.wan:

network.wan=interface
network.wan.device=/dev/ttyUSB0
network.wan.ifname=wwan0
network.wan.proto=ncm
network.wan.apn=internet
network.wan.macaddr=00:01:02:03:04:05

Cezary · 2014-08-19 10:06:17

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

ls -al /lib/netifd/proto/*

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

bhb · 2014-08-19 10:08:17

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

root@OpenWrt:~# ls -al /lib/netifd/proto/*
-rwxr-xr-x 1 root root 2259 Aug 7 23:22 /lib/netifd/proto/3g.sh
-rwxrwxr-x 1 root root 1902 Aug 3 14:47 /lib/netifd/proto/dhcp.sh
-rwxr-xr-x 1 root root 2999 Aug 15 19:22 /lib/netifd/proto/dhcpv6.sh
-rwxr-xr-x 1 root root 2232 Aug 18 19:28 /lib/netifd/proto/ncm.sh
-rwxr-xr-x 1 root root 4717 Aug 15 19:22 /lib/netifd/proto/ppp.sh

Cezary · 2014-08-19 10:10:12

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

Masz gcom/comgt zainstalowany?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

bhb · 2014-08-19 10:16:11

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

Package comgt (0.32-22) installed in root is up to date.

Cezary · 2014-08-19 10:31:43

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

Weź go zrestartuj i bujnij ręcznie przez ifup wan.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

bhb · 2014-08-19 11:10:01

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

jest jakiś problem z wykrywaniem modemu po wyłączeniu zasilania:
log:

Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Tue Aug 19 11:43:41 2014 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Tue Aug 19 11:43:41 2014 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.000000] Kernel command line:  board=TL-WR710N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] Memory: 28652k/32768k available (2352k kernel code, 4116k reserved, 622k data, 224k init, 0k highmem)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.000000] NR_IRQS:51
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.080000] Mount-cache hash table entries: 512
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.090000] NET: Registered protocol family 16
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.100000] MIPS: machine is TP-LINK TL-WR710N v1
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.550000] bio: create slab <bio-0> at 0
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.560000] Switching to clocksource MIPS
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.570000] NET: Registered protocol family 2
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.570000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.570000] TCP: Hash tables configured (established 512 bind 512)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.580000] TCP: reno registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.600000] NET: Registered protocol family 1
Tue Aug 19 11:43:41 2014 kern.debug kernel: [    0.600000] PCI: CLS 0 bytes, default 32
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.640000] msgmni has been set to 55
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.640000] io scheduler noop registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.640000] io scheduler deadline registered (default)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.650000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.670000] console [ttyATH0] enabled, bootconsole disabled
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.690000] m25p80 spi0.0: found s25fl064k, expected m25p80
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.690000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.700000] 5 tp-link partitions found on MTD device spi0.0
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.700000] Creating 5 MTD partitions on "spi0.0":
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.710000] 0x000000000000-0x000000020000 : "u-boot"
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.710000] 0x000000020000-0x00000012d1b8 : "kernel"
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.730000] 0x00000012d1b8-0x0000007f0000 : "rootfs"
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.750000] mtd: device 2 (rootfs) set to be root filesystem
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.750000] 1 squashfs-split partitions found on MTD device rootfs
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.760000] 0x000000380000-0x0000007f0000 : "rootfs_data"
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.770000] 0x0000007f0000-0x000000800000 : "art"
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.770000] 0x000000020000-0x0000007f0000 : "firmware"
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.790000] libphy: ag71xx_mdio: probed
Tue Aug 19 11:43:41 2014 kern.info kernel: [    1.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Tue Aug 19 11:43:41 2014 kern.info kernel: [    1.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Tue Aug 19 11:43:41 2014 kern.info kernel: [    1.910000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.940000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.940000] TCP: cubic registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.950000] NET: Registered protocol family 17
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    2.950000] Bridge firewalling registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.950000] 8021q: 802.1Q VLAN Support v1.8
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.980000] Freeing unused kernel memory: 224K (80348000 - 80380000)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.200000] usbcore: registered new interface driver usbfs
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.210000] usbcore: registered new interface driver hub
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.210000] usbcore: registered new device driver usb
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    6.260000] SCSI subsystem initialized
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.280000] ehci-platform: EHCI generic platform driver
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.290000] ehci-platform ehci-platform: EHCI Host Controller
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.290000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.300000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.330000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.330000] hub 1-0:1.0: USB hub found
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.330000] hub 1-0:1.0: 1 port detected
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.340000] usbcore: registered new interface driver usb-storage
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.670000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.820000] usb-storage 1-1:1.0: USB Mass Storage device detected
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.820000] scsi0 : usb-storage 1-1:1.0
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    7.830000] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Tue Aug 19 11:43:41 2014 kern.info kernel: [    8.940000] eth1: link up (1000Mbps/Full duplex)
Tue Aug 19 11:43:41 2014 kern.notice kernel: [   11.540000] jffs2: notice: (361) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
Tue Aug 19 11:43:41 2014 kern.notice kernel: [   11.630000] jffs2: notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
Tue Aug 19 11:43:41 2014 kern.info kernel: [   11.680000] eth1: link down
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.790000] NET: Registered protocol family 10
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.840000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.850000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.890000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.890000] Backport generated by backports.git backports-20140320-37-g5c33da0
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.910000] ip_tables: (C) 2000-2006 Netfilter Core Team
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.960000] usbcore: registered new interface driver usbserial
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.980000] usbcore: registered new interface driver usbserial_generic
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.980000] usbserial: USB Serial support registered for generic
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.040000] xt_time: kernel timezone is -0000
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.050000] usbcore: registered new interface driver cdc_ether
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.060000] usbcore: registered new interface driver cdc_ncm
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.110000] cfg80211: Calling CRDA to update world regulatory domain
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.110000] cfg80211: World regulatory domain updated:
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.120000] cfg80211:  DFS Master region: unset
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.120000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.130000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.140000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.150000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.160000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.160000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.170000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.180000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.190000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.270000] PPP generic driver version 2.4.2
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.270000] NET: Registered protocol family 24
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.350000] usbcore: registered new interface driver option
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.370000] usbserial: USB Serial support registered for GSM modem (1-port)
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: EEPROM regdomain: 0x0
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: EEPROM indicates default country code should be used
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: doing EEPROM country->regdmn map search
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: country maps to regdmn code: 0x3a
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: Country alpha2 being used: US
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: Regpair used: 0x3a
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.420000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.420000] cfg80211: Calling CRDA for country: US
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.430000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.440000] cfg80211: Regulatory domain changed to country: US
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.450000] cfg80211:  DFS Master region: FCC
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.450000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.460000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.470000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.480000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.480000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.490000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 user.emerg syslog: Error: Failed to connect to ubus
Tue Aug 19 11:43:43 2014 user.emerg syslog: 'radio0' is disabled
Tue Aug 19 11:43:43 2014 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Tue Aug 19 11:43:43 2014 user.emerg syslog: 'radio0' is disabled
Tue Aug 19 11:43:43 2014 user.err syslog: /dev/mtdblock3 is already mounted
Tue Aug 19 11:43:43 2014 user.emerg syslog: block: /dev/mtdblock3 is already mounted
Tue Aug 19 11:43:45 2014 authpriv.info dropbear[938]: Not backgrounding
Tue Aug 19 11:43:46 2014 user.emerg syslog: - init complete -
Tue Aug 19 11:43:48 2014 kern.info kernel: [   25.250000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Tue Aug 19 11:43:48 2014 kern.info kernel: [   25.250000] device eth1 entered promiscuous mode
Tue Aug 19 11:43:48 2014 daemon.notice netifd: Interface 'lan' is enabled
Tue Aug 19 11:43:48 2014 daemon.notice netifd: Interface 'lan' is setting up now
Tue Aug 19 11:43:48 2014 kern.info kernel: [   25.260000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Tue Aug 19 11:43:48 2014 daemon.notice netifd: Interface 'lan' is now up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' is enabled
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' is now up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Network device 'lo' link is up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' has link connectivity 
Tue Aug 19 11:43:49 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.850000] eth1: link up (1000Mbps/Full duplex)
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.850000] br-lan: port 1(eth1) entered forwarding state
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.860000] br-lan: port 1(eth1) entered forwarding state
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.860000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Network device 'eth1' link is up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'lan' has link connectivity 
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.880000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Tue Aug 19 11:43:51 2014 kern.info kernel: [   27.860000] br-lan: port 1(eth1) entered forwarding state
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: started, version 2.71 cachesize 150
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq-dhcp[1075]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: using local addresses only for domain lan
Tue Aug 19 11:43:53 2014 daemon.warn dnsmasq[1075]: no servers found in /tmp/resolv.conf.auto, will retry
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: read /etc/hosts - 1 addresses
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq-dhcp[1075]: read /etc/ethers - 0 addresses
Tue Aug 19 11:44:24 2014 daemon.info dnsmasq-dhcp[1075]: DHCPREQUEST(br-lan) 192.168.1.238 00:16:d3:8d:8e:86 
Tue Aug 19 11:44:24 2014 daemon.info dnsmasq-dhcp[1075]: DHCPACK(br-lan) 192.168.1.238 00:16:d3:8d:8e:86 bhb-ESPRIMO
Tue Aug 19 11:44:29 2014 authpriv.info dropbear[1128]: Child connection from 192.168.1.238:38930
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq[1075]: read /etc/hosts - 1 addresses
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/dhcp - 0 addresses
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/odhcpd - 0 addresses
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq-dhcp[1075]: read /etc/ethers - 0 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq[1075]: read /etc/hosts - 1 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/dhcp - 0 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/odhcpd - 1 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq-dhcp[1075]: read /etc/ethers - 0 addresses
Tue Aug 19 11:44:43 2014 authpriv.notice dropbear[1128]: Password auth succeeded for 'root' from 192.168.1.238:38930

po wysunięciu chwilowym modemu:

Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.580000] TCP: reno registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.600000] NET: Registered protocol family 1
Tue Aug 19 11:43:41 2014 kern.debug kernel: [    0.600000] PCI: CLS 0 bytes, default 32
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.640000] msgmni has been set to 55
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.640000] io scheduler noop registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.640000] io scheduler deadline registered (default)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.650000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.670000] console [ttyATH0] enabled, bootconsole disabled
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.690000] m25p80 spi0.0: found s25fl064k, expected m25p80
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.690000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.700000] 5 tp-link partitions found on MTD device spi0.0
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.700000] Creating 5 MTD partitions on "spi0.0":
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.710000] 0x000000000000-0x000000020000 : "u-boot"
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.710000] 0x000000020000-0x00000012d1b8 : "kernel"
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.730000] 0x00000012d1b8-0x0000007f0000 : "rootfs"
Tue Aug 19 11:43:41 2014 kern.warn kernel: [    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.750000] mtd: device 2 (rootfs) set to be root filesystem
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.750000] 1 squashfs-split partitions found on MTD device rootfs
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.760000] 0x000000380000-0x0000007f0000 : "rootfs_data"
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.770000] 0x0000007f0000-0x000000800000 : "art"
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    0.770000] 0x000000020000-0x0000007f0000 : "firmware"
Tue Aug 19 11:43:41 2014 kern.info kernel: [    0.790000] libphy: ag71xx_mdio: probed
Tue Aug 19 11:43:41 2014 kern.info kernel: [    1.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Tue Aug 19 11:43:41 2014 kern.info kernel: [    1.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Tue Aug 19 11:43:41 2014 kern.info kernel: [    1.910000] ag71xx-mdio.1: Found an AR7240/AR9330 built-in switch
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.940000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.940000] TCP: cubic registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.950000] NET: Registered protocol family 17
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    2.950000] Bridge firewalling registered
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.950000] 8021q: 802.1Q VLAN Support v1.8
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Tue Aug 19 11:43:41 2014 kern.info kernel: [    2.980000] Freeing unused kernel memory: 224K (80348000 - 80380000)
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.200000] usbcore: registered new interface driver usbfs
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.210000] usbcore: registered new interface driver hub
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.210000] usbcore: registered new device driver usb
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    6.260000] SCSI subsystem initialized
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.280000] ehci-platform: EHCI generic platform driver
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.290000] ehci-platform ehci-platform: EHCI Host Controller
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.290000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.300000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.330000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.330000] hub 1-0:1.0: USB hub found
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.330000] hub 1-0:1.0: 1 port detected
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.340000] usbcore: registered new interface driver usb-storage
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.670000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.820000] usb-storage 1-1:1.0: USB Mass Storage device detected
Tue Aug 19 11:43:41 2014 kern.info kernel: [    6.820000] scsi0 : usb-storage 1-1:1.0
Tue Aug 19 11:43:41 2014 kern.notice kernel: [    7.830000] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Tue Aug 19 11:43:41 2014 kern.info kernel: [    8.940000] eth1: link up (1000Mbps/Full duplex)
Tue Aug 19 11:43:41 2014 kern.notice kernel: [   11.540000] jffs2: notice: (361) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
Tue Aug 19 11:43:41 2014 kern.notice kernel: [   11.630000] jffs2: notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
Tue Aug 19 11:43:41 2014 kern.info kernel: [   11.680000] eth1: link down
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.790000] NET: Registered protocol family 10
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.840000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.850000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.890000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.890000] Backport generated by backports.git backports-20140320-37-g5c33da0
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.910000] ip_tables: (C) 2000-2006 Netfilter Core Team
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.960000] usbcore: registered new interface driver usbserial
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.980000] usbcore: registered new interface driver usbserial_generic
Tue Aug 19 11:43:41 2014 kern.info kernel: [   14.980000] usbserial: USB Serial support registered for generic
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.040000] xt_time: kernel timezone is -0000
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.050000] usbcore: registered new interface driver cdc_ether
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.060000] usbcore: registered new interface driver cdc_ncm
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.110000] cfg80211: Calling CRDA to update world regulatory domain
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.110000] cfg80211: World regulatory domain updated:
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.120000] cfg80211:  DFS Master region: unset
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.120000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.130000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.140000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.150000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.160000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.160000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.170000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.180000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.190000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.270000] PPP generic driver version 2.4.2
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.270000] NET: Registered protocol family 24
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.350000] usbcore: registered new interface driver option
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.370000] usbserial: USB Serial support registered for GSM modem (1-port)
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: EEPROM regdomain: 0x0
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: EEPROM indicates default country code should be used
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: doing EEPROM country->regdmn map search
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: country maps to regdmn code: 0x3a
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: Country alpha2 being used: US
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.400000] ath: Regpair used: 0x3a
Tue Aug 19 11:43:41 2014 kern.debug kernel: [   15.420000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.420000] cfg80211: Calling CRDA for country: US
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.430000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.440000] cfg80211: Regulatory domain changed to country: US
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.450000] cfg80211:  DFS Master region: FCC
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.450000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.460000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.470000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.480000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.480000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 kern.info kernel: [   15.490000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Tue Aug 19 11:43:41 2014 user.emerg syslog: Error: Failed to connect to ubus
Tue Aug 19 11:43:43 2014 user.emerg syslog: 'radio0' is disabled
Tue Aug 19 11:43:43 2014 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Tue Aug 19 11:43:43 2014 user.emerg syslog: 'radio0' is disabled
Tue Aug 19 11:43:43 2014 user.err syslog: /dev/mtdblock3 is already mounted
Tue Aug 19 11:43:43 2014 user.emerg syslog: block: /dev/mtdblock3 is already mounted
Tue Aug 19 11:43:45 2014 authpriv.info dropbear[938]: Not backgrounding
Tue Aug 19 11:43:46 2014 user.emerg syslog: - init complete -
Tue Aug 19 11:43:48 2014 kern.info kernel: [   25.250000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Tue Aug 19 11:43:48 2014 kern.info kernel: [   25.250000] device eth1 entered promiscuous mode
Tue Aug 19 11:43:48 2014 daemon.notice netifd: Interface 'lan' is enabled
Tue Aug 19 11:43:48 2014 daemon.notice netifd: Interface 'lan' is setting up now
Tue Aug 19 11:43:48 2014 kern.info kernel: [   25.260000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Tue Aug 19 11:43:48 2014 daemon.notice netifd: Interface 'lan' is now up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' is enabled
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' is now up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Network device 'lo' link is up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'loopback' has link connectivity 
Tue Aug 19 11:43:49 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.850000] eth1: link up (1000Mbps/Full duplex)
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.850000] br-lan: port 1(eth1) entered forwarding state
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.860000] br-lan: port 1(eth1) entered forwarding state
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.860000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Network device 'eth1' link is up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Aug 19 11:43:49 2014 daemon.notice netifd: Interface 'lan' has link connectivity 
Tue Aug 19 11:43:49 2014 kern.info kernel: [   25.880000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Tue Aug 19 11:43:51 2014 kern.info kernel: [   27.860000] br-lan: port 1(eth1) entered forwarding state
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: started, version 2.71 cachesize 150
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq-dhcp[1075]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: using local addresses only for domain lan
Tue Aug 19 11:43:53 2014 daemon.warn dnsmasq[1075]: no servers found in /tmp/resolv.conf.auto, will retry
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq[1075]: read /etc/hosts - 1 addresses
Tue Aug 19 11:43:53 2014 daemon.info dnsmasq-dhcp[1075]: read /etc/ethers - 0 addresses
Tue Aug 19 11:44:24 2014 daemon.info dnsmasq-dhcp[1075]: DHCPREQUEST(br-lan) 192.168.1.238 00:16:d3:8d:8e:86 
Tue Aug 19 11:44:24 2014 daemon.info dnsmasq-dhcp[1075]: DHCPACK(br-lan) 192.168.1.238 00:16:d3:8d:8e:86 bhb-ESPRIMO
Tue Aug 19 11:44:29 2014 authpriv.info dropbear[1128]: Child connection from 192.168.1.238:38930
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq[1075]: read /etc/hosts - 1 addresses
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/dhcp - 0 addresses
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/odhcpd - 0 addresses
Tue Aug 19 11:44:31 2014 daemon.info dnsmasq-dhcp[1075]: read /etc/ethers - 0 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq[1075]: read /etc/hosts - 1 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/dhcp - 0 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq[1075]: read /tmp/hosts/odhcpd - 1 addresses
Tue Aug 19 11:44:32 2014 daemon.info dnsmasq-dhcp[1075]: read /etc/ethers - 0 addresses
Tue Aug 19 11:44:43 2014 authpriv.notice dropbear[1128]: Password auth succeeded for 'root' from 192.168.1.238:38930
Tue Aug 19 11:47:31 2014 kern.info kernel: [  247.560000] usb 1-1: USB disconnect, device number 2
Tue Aug 19 11:47:43 2014 kern.info kernel: [  260.200000] usb 1-1: new high-speed USB device number 3 using ehci-platform
Tue Aug 19 11:47:44 2014 kern.info kernel: [  260.390000] usb-storage 1-1:1.0: USB Mass Storage device detected
Tue Aug 19 11:47:44 2014 kern.info kernel: [  260.390000] scsi1 : usb-storage 1-1:1.0
Tue Aug 19 11:47:44 2014 kern.info kernel: [  260.860000] usb 1-1: USB disconnect, device number 3
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.310000] usb 1-1: new high-speed USB device number 4 using ehci-platform
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.470000] option 1-1:1.0: GSM modem (1-port) converter detected
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.480000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.480000] option 1-1:1.1: GSM modem (1-port) converter detected
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.490000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.510000] option 1-1:1.2: GSM modem (1-port) converter detected
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.510000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.530000] usb 1-1: MAC-Address: 0c:5b:8f:27:9a:64
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.530000] cdc_ncm 1-1:1.3 wwan0: register 'cdc_ncm' at usb-ehci-platform-1, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
Tue Aug 19 11:47:45 2014 daemon.notice netifd: Interface 'wan' is enabled
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.550000] IPv6: ADDRCONF(NETDEV_UP): wwan0: link is not ready
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.560000] usb-storage 1-1:1.4: USB Mass Storage device detected
Tue Aug 19 11:47:45 2014 kern.info kernel: [  261.560000] scsi2 : usb-storage 1-1:1.4
Tue Aug 19 11:47:46 2014 kern.notice kernel: [  262.580000] scsi 2:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Tue Aug 19 11:47:46 2014 kern.notice kernel: [  262.590000] sd 2:0:0:0: [sda] Attached SCSI removable disk
Tue Aug 19 11:47:47 2014 user.err syslog: Unkown action change
Tue Aug 19 11:47:47 2014 user.err syslog: Unkown action change
Tue Aug 19 11:48:04 2014 daemon.notice netifd: Interface 'wan' is disabled
Tue Aug 19 11:48:04 2014 daemon.notice netifd: Interface 'wan' is enabled
Tue Aug 19 11:48:04 2014 kern.info kernel: [  280.350000] IPv6: ADDRCONF(NETDEV_UP): wwan0: link is not ready

mar_w · 2014-08-19 14:49:57

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

Mam to samo co @bhb czyli:
USB:

root@OpenWrt:~# cat /sys/kernel/debug/usb/devices 

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.10
S:  Manufacturer=Linux 3.10.49 ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1506 Rev= 1.02
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:  If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:* If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

logread przed komendą ifup wan (najważniejsza część)

(...)Mon Aug 18 19:52:40 2014 kern.info kernel: [  139.820000] usb 1-1: new high-speed USB device number 4 using ehci-platform
Mon Aug 18 19:52:40 2014 kern.info kernel: [  139.980000] option 1-1:1.0: GSM modem (1-port) converter detected
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.000000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.010000] usb 1-1: MAC-Address: 0c:5b:8f:27:9a:64
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.030000] cdc_ncm 1-1:1.1 wwan0: register 'cdc_ncm' at usb-ehci-platform-1, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.040000] IPv6: ADDRCONF(NETDEV_UP): wwan0: link is not ready
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.070000] usb-storage 1-1:1.2: USB Mass Storage device detected
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.070000] scsi4 : usb-storage 1-1:1.2
Mon Aug 18 19:52:40 2014 daemon.notice netifd: Interface 'wan' is enabled
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.100000] usb-storage 1-1:1.3: USB Mass Storage device detected
Mon Aug 18 19:52:40 2014 kern.info kernel: [  140.100000] scsi5 : usb-storage 1-1:1.3
Mon Aug 18 19:52:41 2014 kern.notice kernel: [  141.100000] scsi 4:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Mon Aug 18 19:52:41 2014 kern.notice kernel: [  141.130000] scsi 5:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Mon Aug 18 19:52:41 2014 kern.notice kernel: [  141.170000] sd 5:0:0:0: [sda] Attached SCSI removable disk
Mon Aug 18 19:52:42 2014 user.err syslog: Unkown action change
Mon Aug 18 19:52:42 2014 user.err syslog: Unkown action change

Teraz było ifup wan i logread dopisał tylko to:

(...)Mon Aug 18 19:55:59 2014 daemon.notice netifd: Interface 'wan' is disabled
Mon Aug 18 19:55:59 2014 daemon.notice netifd: Interface 'wan' is enabled
Mon Aug 18 19:55:59 2014 kern.info kernel: [  338.830000] IPv6: ADDRCONF(NETDEV_UP): wwan0: link is not ready

uci show network.wan

root@OpenWrt:~# uci show network.wan
network.wan=interface
network.wan.ifname=wwan0
network.wan.proto=ncm
network.wan.apn=internet
network.wan.device=/dev/ttyUSB0
network.wan.macaddr=00:01:02:03:04:05

protokoły

root@OpenWrt:~# ls -al /lib/netifd/proto/*
-rwxr-xr-x    1 root     root          2259 Aug  7 23:22 /lib/netifd/proto/3g.sh
-rwxrwxr-x    1 root     root          1902 Aug  3 14:47 /lib/netifd/proto/dhcp.sh
-rwxr-xr-x    1 root     root          2999 Aug 15 19:22 /lib/netifd/proto/dhcpv6.sh
-rwxr-xr-x    1 root     root          2232 Aug 18 19:28 /lib/netifd/proto/ncm.sh
-rwxr-xr-x    1 root     root          4717 Aug 15 19:22 /lib/netifd/proto/ppp.sh

comgt

root@OpenWrt:~# opkg list-installed |grep comgt
comgt - 0.32-22

ifconfig wwan0

root@OpenWrt:~# ifconfig wwan0
wwan0     Link encap:Ethernet  HWaddr 00:01:02:03:04:05  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Bez macaddr w konfigu jest dokładnie to samo co wyżej....

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

onken · 2014-08-19 15:36:07

onken
Użytkownik
Nieaktywny

Zarejestrowany: 2014-06-13
Posty: 2,368

Odp: Tester z E3276 potrzebny

Panowie, Cezary

Wrzuciłem E3272, i mam chyba podobne objawy co reszta:

 
 cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  2, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.10
S:  Manufacturer=Linux 3.10.49 ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05e3 ProdID=0608 Rev=85.36
S:  Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1506 Rev= 1.02
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:  If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:* If#= 2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

uci show network.wan

network.wan=interface
network.wan.ifname=wwan0
network.wan.proto=ncm
network.wan.device=/dev/ttyUSB0
network.wan.apn=internet.cp
network.wan.macaddr=00:01:02:03:04:05

mar_w · 2014-08-19 15:49:13

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

Pan Cezary napisał w poście nr 21 że Twój modem wymaga sterowników QMI i pewnie bez tego nie masz w ogóle interfejsu wwan0 tylko pewnie usb0 bo to Hi-Link jest. Sprawdź to dokładnie.
PS do postu poniżej. Jedyne co mnie wkurza u Huawei-a to to, że pod jedną nazwą mają 2 typy modemów. Jakby nie mogli zmienić cyferki. A niektórzy sprzedawcy na pytanie "Hi-Link czy zwykły?" dostają oczy jak 5 zł.
Mój też działa (tzn. łączy) na Gargoyle na pożyczonym MR3220.

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

onken · 2014-08-19 16:00:21

onken
Użytkownik
Nieaktywny

Zarejestrowany: 2014-06-13
Posty: 2,368

Odp: Tester z E3276 potrzebny

Nie, to jest zwykly modem nie Hilink, mam tez wersje Hilink ale testujemy inny modem :-) . Ps, jako ndis na gargoylu dziala i jako modem na 3gwan

bhb · 2014-08-19 16:24:33

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

moj modem to 12d1:1506 czy powinien być w pliku usb-mode.json ? ewentualnie jak go dopisać ?

mar_w · 2014-08-19 16:37:02

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

bhb napisał/a:

moj modem to 12d1:1506 czy powinien być w pliku usb-mode.json ? ewentualnie jak go dopisać ?

U mnie też tego nie ma. Różnice między Twoimi logami a moimi po wypięciu modemu i włożeniu są takie, że u Ciebie jest dodatkowo:
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
a u mnie tego nie ma. Jest tylko ttyUSB0. Reszta tak samo w logach. Pewnie to wynika z konfiguracji modemu. U mnie:
at^setport?
^SETPORT:A1,A2;12,16,A1,A2.

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

bhb · 2014-08-19 17:01:05

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

ja mam
^SETPORT:A1;10,12,13,16,A2

mar_w · 2014-08-19 17:17:26

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

bhb napisał/a:

ja mam
^SETPORT:A1;10,12,13,16,A2

A ciekawe czy poprawi się wykrywanie modemu jak wklepiesz:
AT^SETPORT="A1;12,16,A1" - Im mniej klamotów tym lepiej Ale niech w tym temacie wypowiedzą się mistrzowie.

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

Cezary · 2014-08-19 17:45:17

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

bhb napisał/a:

moj modem to 12d1:1506 czy powinien być w pliku usb-mode.json ? ewentualnie jak go dopisać ?

Nie, on już jest przełączony.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

onken · 2014-08-19 17:46:36

onken
Użytkownik
Nieaktywny

Zarejestrowany: 2014-06-13
Posty: 2,368

Odp: Tester z E3276 potrzebny

Cezary, moze masz jaki pomysl w czym problem u mnie ? Interfejs wwan0 sie tworzy

bhb · 2014-08-19 18:06:35

bhb
Użytkownik
Nieaktywny

Skąd: Włocławek
Zarejestrowany: 2012-04-09
Posty: 335

Odp: Tester z E3276 potrzebny

Po reboot ttyUSB0 nie znika ale po wyłączaniu zasilanie nie ma go. Polecenie usbmode -s przywraca ttyUSB0.

Cezary · 2014-08-19 18:23:09

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

Na e173 działa poprawnie zgodnie z pierwszym postem. Log wygląda tak:

Tue Aug 19 19:21:42 2014 daemon.notice netifd: Network device 'wwan0' link is up
Tue Aug 19 19:21:42 2014 daemon.notice netifd: Interface 'wan' has link connectivity 
Tue Aug 19 19:21:42 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Establishing 3G modem connection in NDIS mode
Tue Aug 19 19:21:42 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Script for comgt version 1.09 Rafal Drzymala 2012,2013
Tue Aug 19 19:21:42 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Try to communicate with modem
Tue Aug 19 19:21:43 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Checking modem for NDIS support
Tue Aug 19 19:21:43 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 - NDIS mode is supported by this modem
Tue Aug 19 19:21:43 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Getting network registration status
Tue Aug 19 19:21:44 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 - status: Local network is registered
Tue Aug 19 19:21:44 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 - lac, ci:  6F, 2DA8
Tue Aug 19 19:21:44 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Verify if the modem is connected to APN
Tue Aug 19 19:21:44 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 No connection detected
Tue Aug 19 19:21:44 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Try to establish connection via APN internet
Tue Aug 19 19:21:45 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Waiting for establish connection
Tue Aug 19 19:21:46 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Still waiting 2 second(s)...
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Connection established
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan (1743): ndisup:ttyUSB0 Done.
Tue Aug 19 19:21:48 2014 daemon.info ncm[1743]: Connected, starting DHCP
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan6' is enabled
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan6' is setting up now
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan' is now up
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan_dhcp' is enabled
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan_dhcp' has link connectivity 
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan_dhcp' is setting up now
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan (1743): Command failed: Unknown error
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan_dhcpv6' is enabled
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan_dhcpv6' has link connectivity 
Tue Aug 19 19:21:48 2014 daemon.notice netifd: Interface 'wan_dhcpv6' is setting up now
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan (1743): Command failed: Unknown error
Tue Aug 19 19:21:48 2014 daemon.notice odhcp6c[1780]: (re)starting transaction on wwan0
Tue Aug 19 19:21:48 2014 daemon.notice odhcp6c[1780]: Starting SOLICIT transaction (timeout 4294967295s, max rc 0)
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan_dhcp (1789): udhcpc (v1.22.1) started
Tue Aug 19 19:21:48 2014 user.notice firewall: Reloading firewall due to ifup of wan (wwan0)
Tue Aug 19 19:21:48 2014 daemon.notice odhcp6c[1793]: (re)starting transaction on wwan0
Tue Aug 19 19:21:48 2014 daemon.notice odhcp6c[1793]: Starting SOLICIT transaction (timeout 4294967295s, max rc 0)
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan_dhcp (1789): Sending discover...
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan_dhcp (1789): Sending select for 109.243.152.184...
Tue Aug 19 19:21:48 2014 daemon.notice netifd: wan_dhcp (1789): Lease of 109.243.152.184 obtained, lease time 7200
Tue Aug 19 19:21:49 2014 daemon.notice netifd: Interface 'wan_dhcp' is now up

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mar_w · 2014-08-19 18:41:03

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

U nas nie działa jakby IPv6:

IPv6: ADDRCONF(NETDEV_UP): wwan0: link is not ready

a u Ciebie działa:

daemon.notice netifd: Interface 'wan_dhcpv6' has link connectivity

A można wywalić to IPv6 z naszych skryptów. Napisz gdzie i jak bo tylko to nas blokuje

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

Cezary · 2014-08-19 18:48:44

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

Domyślnie w konfigu masz:

config interface 'wan6'
        option ifname '@wan'
        option proto 'dhcpv6'

wwan0     Link encap:Ethernet  HWaddr 00:01:02:03:04:05  
          inet addr:109.243.152.184  Bcast:109.243.152.191  Mask:255.255.255.240
          inet6 addr: fe80::201:2ff:fe03:405/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:231 errors:0 dropped:0 overruns:0 frame:0
          TX packets:298 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:16561 (16.1 KiB)  TX bytes:30275 (29.5 KiB)

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

mar_w · 2014-08-19 18:59:31

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

Nic nie dało wyhaszowanie odpowiednich wpisów w konfigu. Cały czas:

Mon Aug 18 21:39:23 2014 kern.info kernel: [   49.230000] IPv6: ADDRCONF(NETDEV_UP): wwan0: link is not ready
root@OpenWrt:~# ifconfig wwan0
wwan0     Link encap:Ethernet  HWaddr 00:01:02:03:04:05  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Przynajmniej zostało sprawdzone również z poleceniem ifup wan. To samo cały czas

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

Cezary · 2014-08-19 19:02:42

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 115,872

Odp: Tester z E3276 potrzebny

Zapomnij o ipv6. to jest ważne: ndisup:ttyUSB0 Establishing 3G modem connection in NDIS mode itd, co znaczy że gcom nazwiązał połączenie.

Zróbcie z konsoli

APN=internet gcom -d /dev/ttyUSB0 -s /etc/gcom/ncmup.gcom

i pokażcie wynik

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

onken · 2014-08-19 19:06:08

onken
Użytkownik
Nieaktywny

Zarejestrowany: 2014-06-13
Posty: 2,368

Odp: Tester z E3276 potrzebny

u mnie tak:

root@OpenWrt:~# APN=internet.cp gcom -d /dev/ttyUSB0 -s /etc/gcom/ncmup.gcom
ndisup:ttyUSB0 Establishing 3G modem connection in NDIS mode
ndisup:ttyUSB0 Script for comgt version 1.09 Rafal Drzymala 2012,2013
ndisup:ttyUSB0 Try to communicate with modem
ndisup:ttyUSB0 Checking modem for NDIS support
ndisup:ttyUSB0 - NDIS mode is supported by this modem
ndisup:ttyUSB0 Getting network registration status
ndisup:ttyUSB0 Error while getting network registration status
ndisup:ttyUSB0 Verify if the modem is connected to APN
ndisup:ttyUSB0 Modem is not responding, timeout detected
ndisup:ttyUSB0 Restarting modem
ndisup:ttyUSB0 Still waiting 7 second(s)...
ndisup:ttyUSB0 Still waiting 11 second(s)...
ndisup:ttyUSB0 Still waiting 15 second(s)...
ndisup:ttyUSB0 Still waiting 19 second(s)...
ndisup:ttyUSB0 Again try to communicate with modem (2)
ndisup:ttyUSB0 Checking modem for NDIS support
ndisup:ttyUSB0 - NDIS mode is supported by this modem
ndisup:ttyUSB0 Getting network registration status
ndisup:ttyUSB0 Error while getting network registration status
ndisup:ttyUSB0 Verify if the modem is connected to APN
ndisup:ttyUSB0 Modem is not responding, timeout detected
ndisup:ttyUSB0 Restarting modem

mar_w · 2014-08-19 19:06:56

mar_w
Użytkownik
Nieaktywny

Zarejestrowany: 2014-08-16
Posty: 2,124

Odp: Tester z E3276 potrzebny

root@OpenWrt:~# APN=internet gcom -d /dev/ttyUSB0 -s /etc/gcom/ncmup.gcom 
ndisup:ttyUSB0 Establishing 3G modem connection in NDIS mode
ndisup:ttyUSB0 Script for comgt version 1.09 Rafal Drzymala 2012,2013
ndisup:ttyUSB0 Try to communicate with modem
ndisup:ttyUSB0 Checking modem for NDIS support
ndisup:ttyUSB0 - NDIS mode is supported by this modem
ndisup:ttyUSB0 Getting network registration status
ndisup:ttyUSB0 Error while getting network registration status
ndisup:ttyUSB0 Verify if the modem is connected to APN
ndisup:ttyUSB0 No connection detected
ndisup:ttyUSB0 Try to establish connection via APN internet
ndisup:ttyUSB0 Waiting for establish connection
ndisup:ttyUSB0 Connection established
ndisup:ttyUSB0 Done.

root@OpenWrt:~# ifconfig wwan0
wwan0     Link encap:Ethernet  HWaddr 00:01:02:03:04:05  
          inet addr:10.236.85.49  Bcast:10.236.85.51  Mask:255.255.255.252
          inet6 addr: fe80::201:2ff:fe03:405/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:34 errors:0 dropped:0 overruns:0 frame:0
          TX packets:53 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:4100 (4.0 KiB)  TX bytes:110329 (107.7 KiB)

HULA, HURRRRAAAAA

Xiaomi AX3000T @ Netgear R6220
* DVBT2 - T230C *

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Tester z E3276 potrzebny (Strona 2 z 6)

Posty: 26 do 50 z 145

26 Odpowiedź przez bhb 2014-08-19 09:59:51

Odp: Tester z E3276 potrzebny

27 Odpowiedź przez Cezary 2014-08-19 10:06:17

Odp: Tester z E3276 potrzebny

28 Odpowiedź przez bhb 2014-08-19 10:08:17

Odp: Tester z E3276 potrzebny

29 Odpowiedź przez Cezary 2014-08-19 10:10:12

Odp: Tester z E3276 potrzebny

30 Odpowiedź przez bhb 2014-08-19 10:16:11

Odp: Tester z E3276 potrzebny

31 Odpowiedź przez Cezary 2014-08-19 10:31:43

Odp: Tester z E3276 potrzebny

32 Odpowiedź przez bhb 2014-08-19 11:10:01

Odp: Tester z E3276 potrzebny

33 Odpowiedź przez mar_w 2014-08-19 14:49:57 (edytowany przez mar_w 2014-08-19 14:55:03)

Odp: Tester z E3276 potrzebny

34 Odpowiedź przez onken 2014-08-19 15:36:07 (edytowany przez onken 2014-08-19 15:37:35)

Odp: Tester z E3276 potrzebny

35 Odpowiedź przez mar_w 2014-08-19 15:49:13 (edytowany przez mar_w 2014-08-19 16:24:59)

Odp: Tester z E3276 potrzebny

36 Odpowiedź przez onken 2014-08-19 16:00:21 (edytowany przez onken 2014-08-19 16:08:32)

Odp: Tester z E3276 potrzebny

37 Odpowiedź przez bhb 2014-08-19 16:24:33

Odp: Tester z E3276 potrzebny

38 Odpowiedź przez mar_w 2014-08-19 16:37:02 (edytowany przez mar_w 2014-08-19 16:39:59)

Odp: Tester z E3276 potrzebny

39 Odpowiedź przez bhb 2014-08-19 17:01:05

Odp: Tester z E3276 potrzebny

40 Odpowiedź przez mar_w 2014-08-19 17:17:26

Odp: Tester z E3276 potrzebny

41 Odpowiedź przez Cezary 2014-08-19 17:45:17

Odp: Tester z E3276 potrzebny

42 Odpowiedź przez onken 2014-08-19 17:46:36

Odp: Tester z E3276 potrzebny

43 Odpowiedź przez bhb 2014-08-19 18:06:35

Odp: Tester z E3276 potrzebny

44 Odpowiedź przez Cezary 2014-08-19 18:23:09

Odp: Tester z E3276 potrzebny

45 Odpowiedź przez mar_w 2014-08-19 18:41:03

Odp: Tester z E3276 potrzebny

46 Odpowiedź przez Cezary 2014-08-19 18:48:44

Odp: Tester z E3276 potrzebny

47 Odpowiedź przez mar_w 2014-08-19 18:59:31 (edytowany przez mar_w 2014-08-19 19:00:57)

Odp: Tester z E3276 potrzebny

48 Odpowiedź przez Cezary 2014-08-19 19:02:42

Odp: Tester z E3276 potrzebny

49 Odpowiedź przez onken 2014-08-19 19:06:08 (edytowany przez onken 2014-08-19 19:09:31)

Odp: Tester z E3276 potrzebny

50 Odpowiedź przez mar_w 2014-08-19 19:06:56 (edytowany przez mar_w 2014-08-19 19:09:21)

Odp: Tester z E3276 potrzebny

Posty: 26 do 50 z 145