• Zarejestrowany: 2014-07-03
  • Posty: 19

Temat: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Witajcie, jestem nowy na forum, choć trochę czasu już tu spędziłem szukając pomocy w istniejących tematach.
Sytuacja jak w temacie, ponadto:
- połączenie w trybie NDIS
- chcę uniknąć korzystania z Gargoyle (mimo, że tam wszystko działa bez najmniejszego problemu), bo potrzebuję doinstalować kilka package'ów, a do tego potrzebuję pamięci
Oto, jakie kroki wykonuję:
1. Instalacja:

opkg install kmod-usb-net libusb kmod-usb2 usb-modeswitch usb-modeswitch-data kmod-usb-serial kmod-usb-core kmod-usb-serial-option chat comgt

a z 

http://dl.eko.one.pl/attitude_adjustment/ar71xx/packages

jeszcze 

opkg install kmod-usb-net-cdc-ncm

W tym miejscu otrzymuję dziwny błąd od opkg, wymagany jest downgrade paczki kernel big_smile
Po podłączeniu modem ustawia się (chyba) we właściwym trybie:

#cat /proc/bus/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05e3 ProdID=0608 Rev=85.36
S:  Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1506 Rev= 1.02
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:  If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:* If#= 2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

2. Konfiguracja i łączenie:
ogólnie używam takiego skryptu, którego każdą linię pobrałem z tego forum:

#!/bin/sh
DEBUG=
PORT=/dev/ttyUSB0
ETH=wwan0

ifdown wan
uci del network.wan
uci set network.wan=interface
uci set network.wan.proto=dhcp
uci set network.wan.auto=0
uci set network.wan.ifname=wwan0
uci commit network
ifup wan

MODE="AT^NDISDUP=1,0" gcom -d $PORT -s /etc/gcom/setmode.gcom
sleep 3
MODE="AT^NDISDUP=1,1,\"internet\",\"internet\",\"internet\"" gcom -d $PORT -s /etc/gcom/setmode.gcom
sleep 3

A=`((sleep 1 && echo -e "AT^DHCP?\r" >$PORT) &) &&  grep -m1 "DHCP:" $PORT | cut -f2 -d:`

IP=$(echo "$A" | cut -f1 -d, | sed 's/ //g')
NETMASK=$(echo "$A" | cut -f2 -d,)
GATEWAY=$(echo "$A" | cut -f3 -d,)
if [ ${#IP} -eq "8" ] && [ ${#NETMASK} -eq "8" ] && [ ${#GATEWAY} -eq "8" ]; then
    IP=$(printf "%d.%d.%d.%d" 0x${IP:6:2} 0x${IP:4:2} 0x${IP:2:2} 0x${IP:0:2})
    NETMASK=$(printf "%d.%d.%d.%d" 0x${NETMASK:6:2} 0x${NETMASK:4:2} 0x${NETMASK:2:2} 0x${NETMASK:0:2})
    GATEWAY=$(printf "%d.%d.%d.%d" 0x${GATEWAY:6:2} 0x${GATEWAY:4:2} 0x${GATEWAY:2:2} 0x${GATEWAY:0:2})
    $DEBUG ifconfig $ETH $IP netmask $NETMASK
    $DEBUG ip route add default via $GATEWAY
fi

Niestety gcom rzuca błędami:

Error @39, line 2, Can't control /dev/ttyUSB0/, please try again.

Zupełnie nie rozumiem dlaczego nie ma dostępu do urządzenia. Jak mogę sprawdzić w czym problem? Wrzucam logi z bootowania po instalacji, konfiguracji, z wpiętym modemem.

Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 16:49:30 UTC 2013
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000] MyLoader: sysp=84c31530, boardp=0065cbe4, parts=195ef6a4
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] bootconsole [early0] enabled
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] SoC: Atheros AR9344 rev 2
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Determined physical RAM map:
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000]  memory: 08000000 @ 00000000 (usable)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000] Zone PFN ranges:
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000]   Normal   0x00000000 -> 0x00008000
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000] Movable zone start PFN for each node
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000] Early memory PFN ranges
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000]     0: 0x00000000 -> 0x00008000
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000] On node 0 totalpages: 32768
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 802f1100, node_mem_map 81000000
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000]   Normal zone: 256 pages used for memmap
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000]   Normal zone: 32512 pages, LIFO batch:7
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0 
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.000000] Kernel command line:  board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Memory: 126464k/131072k available (2211k kernel code, 4608k reserved, 418k data, 212k init, 0k highmem)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] NR_IRQS:51
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.070000] pid_max: default: 32768 minimum: 301
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.070000] Mount-cache hash table entries: 512
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.080000] NET: Registered protocol family 16
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.090000] registering PCI controller with io_map_base unset
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.310000] bio: create slab <bio-0> at 0
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.310000] PCI host bridge to bus 0000:00
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.320000] pci_bus 0000:00: root bus resource [io  0x0000]
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.330000] pci 0000:00:00.0: [168c:0033] type 0 class 0x000280
Sep  8 15:44:03 OpenWrt kern.err kernel: [    0.330000] pci 0000:00:00.0: invalid calibration data
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.330000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.330000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.330000] pci 0000:00:00.0: supports D1
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.340000] pci 0000:00:00.0: using irq 40 for pin 1
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.350000] Switching to clocksource MIPS
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.350000] NET: Registered protocol family 2
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.370000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.370000] TCP: Hash tables configured (established 4096 bind 4096)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.380000] TCP reno registered
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.390000] NET: Registered protocol family 1
Sep  8 15:44:03 OpenWrt kern.debug kernel: [    0.400000] PCI: CLS 0 bytes, default 32
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.430000] msgmni has been set to 247
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.440000] io scheduler noop registered
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.440000] io scheduler deadline registered (default)
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.490000] console [ttyS0] enabled, bootconsole disabled
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.500000] m25p80 spi0.0: found s25fl064k, expected m25p80
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.510000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.510000] 5 tp-link partitions found on MTD device spi0.0
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.520000] Creating 5 MTD partitions on "spi0.0":
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.520000] 0x000000000000-0x000000020000 : "u-boot"
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.530000] 0x000000020000-0x000000109d54 : "kernel"
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.550000] 0x000000109d54-0x0000007f0000 : "rootfs"
Sep  8 15:44:03 OpenWrt kern.warn kernel: [    0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.570000] mtd: partition "rootfs" set to be root filesystem
Sep  8 15:44:03 OpenWrt kern.info kernel: [    0.570000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=510000 
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.580000] 0x0000002e0000-0x0000007f0000 : "rootfs_data"
Sep  8 15:44:03 OpenWrt kern.notice kernel: [    0.590000] 0x0000007f0000-0x000000800000 : "art"
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.560000] USB Serial support registered for generic
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.570000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.730000] hub 1-1:1.0: USB hub found
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.730000] hub 1-1:1.0: 4 ports detected
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.740000] usbcore: registered new interface driver usbserial_generic
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.750000] usbserial: USB Serial Driver core
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.780000] usbcore: registered new interface driver cdc_ncm
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.800000] USB Serial support registered for GSM modem (1-port)
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.810000] usbcore: registered new interface driver option
Sep  8 15:44:03 OpenWrt kern.info kernel: [   10.820000] option: v0.7.2:USB Driver for GSM modems
Sep  8 15:44:03 OpenWrt kern.info kernel: [   11.020000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
Sep  8 15:44:05 OpenWrt kern.info kernel: [   14.000000] device eth0.1 entered promiscuous mode
Sep  8 15:44:05 OpenWrt kern.info kernel: [   14.010000] device eth0 entered promiscuous mode
Sep  8 15:44:05 OpenWrt daemon.notice netifd: Interface 'lan' is now up
Sep  8 15:44:05 OpenWrt daemon.notice netifd: Interface 'loopback' is now up
Sep  8 15:44:06 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Sep  8 15:44:06 OpenWrt user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Sep  8 15:44:06 OpenWrt user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0_Hub Serial=?
Sep  8 15:44:06 OpenWrt user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:06 OpenWrt user.notice usb-modeswitch: 1-1.1:1.0: Selecting /etc/usb_modeswitch.d/12d1:14fe for mode switching
Sep  8 15:44:07 OpenWrt syslog.notice usb_modeswitch: switching device 12d1:14fe on 001/003
Sep  8 15:44:07 OpenWrt kern.info kernel: [   15.600000] usb 1-1.1: USB disconnect, device number 3
Sep  8 15:44:07 OpenWrt kern.info kernel: [   15.640000] eth0: link up (1000Mbps/Full duplex)
Sep  8 15:44:07 OpenWrt kern.info kernel: [   15.660000] br-lan: port 1(eth0.1) entered forwarding state
Sep  8 15:44:07 OpenWrt kern.info kernel: [   15.660000] br-lan: port 1(eth0.1) entered forwarding state
Sep  8 15:44:07 OpenWrt kern.info kernel: [   15.910000] usb 1-1.1: new high-speed USB device number 4 using ehci-platform
Sep  8 15:44:07 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Sep  8 15:44:07 OpenWrt kern.info kernel: [   16.020000] usb 1-1.1: MAC-Address: 0x0c:0x5b:0x8f:0x27:0x9a:0x64
Sep  8 15:44:07 OpenWrt kern.info kernel: [   16.030000] cdc_ncm 1-1.1:1.2: wwan0: register 'cdc_ncm' at usb-ehci-platform-1.1, Mobile Broadband Network Device, 0c:5b:8f:27:9a:64
Sep  8 15:44:09 OpenWrt kern.info kernel: [   17.660000] br-lan: port 1(eth0.1) entered forwarding state
Sep  8 15:44:09 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:09 OpenWrt user.info sysinit: 'radio1' is disabled
Sep  8 15:44:10 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:10 OpenWrt user.info sysinit: 'radio1' is disabled
Sep  8 15:44:10 OpenWrt user.info sysinit: 'radio0' is disabled
Sep  8 15:44:10 OpenWrt user.info sysinit: 'radio1' is disabled
Sep  8 15:44:11 OpenWrt user.info sysinit: Loading defaults
Sep  8 15:44:11 OpenWrt user.info sysinit: Loading synflood protection
Sep  8 15:44:11 OpenWrt user.info sysinit: Adding custom chains
Sep  8 15:44:12 OpenWrt user.info sysinit: Loading zones
Sep  8 15:44:12 OpenWrt user.info sysinit: Loading forwardings
Sep  8 15:44:12 OpenWrt user.info sysinit: Loading rules
Sep  8 15:44:12 OpenWrt user.info sysinit: Loading redirects
Sep  8 15:44:12 OpenWrt user.info sysinit: Loading includes
Sep  8 15:44:12 OpenWrt user.info sysinit: Optimizing conntrack
Sep  8 15:44:12 OpenWrt user.info sysinit: Loading interfaces
Sep  8 15:44:13 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Sep  8 15:44:14 OpenWrt authpriv.info dropbear[1119]: Running in background
Sep  8 15:44:15 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Sep  8 15:44:15 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Sep  8 15:44:19 OpenWrt daemon.info dnsmasq[1171]: started, version 2.62 cachesize 150
Sep  8 15:44:19 OpenWrt daemon.info dnsmasq[1171]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Sep  8 15:44:19 OpenWrt daemon.info dnsmasq-dhcp[1171]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Sep  8 15:44:19 OpenWrt daemon.info dnsmasq[1171]: using local addresses only for domain lan
Sep  8 15:44:19 OpenWrt daemon.warn dnsmasq[1171]: no servers found in /tmp/resolv.conf.auto, will retry
Sep  8 15:44:19 OpenWrt daemon.info dnsmasq[1171]: read /etc/hosts - 1 addresses
Sep  8 15:44:19 OpenWrt daemon.info dnsmasq-dhcp[1171]: read /etc/ethers - 0 addresses
Sep  8 15:44:19 OpenWrt user.info sysinit: setting up led USB1
Sep  8 15:44:19 OpenWrt user.info sysinit: setting up led USB2
Sep  8 15:44:19 OpenWrt user.info sysinit: setting up led WLAN2G
Sep  8 15:44:22 OpenWrt daemon.info dnsmasq-dhcp[1171]: DHCPREQUEST(br-lan) 192.168.1.203 00:26:9e:f7:c8:bf 
Sep  8 15:44:22 OpenWrt daemon.info dnsmasq-dhcp[1171]: DHCPACK(br-lan) 192.168.1.203 00:26:9e:f7:c8:bf ElektrycznyPiec
Sep  8 15:44:26 OpenWrt daemon.info dnsmasq-dhcp[1171]: DHCPINFORM(br-lan) 192.168.1.203 00:26:9e:f7:c8:bf 
Sep  8 15:44:26 OpenWrt daemon.info dnsmasq-dhcp[1171]: DHCPACK(br-lan) 192.168.1.203 00:26:9e:f7:c8:bf ElektrycznyPiec
Sep  8 15:44:37 OpenWrt user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:41 OpenWrt user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:41 OpenWrt user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:41 OpenWrt user.notice usb-modeswitch: 1-1.1:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:41 OpenWrt user.notice usb-modeswitch: 1-1.1:1.3: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:41 OpenWrt user.notice usb-modeswitch: 1-1.1:1.4: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?
Sep  8 15:44:59 OpenWrt authpriv.info dropbear[1421]: Child connection from 192.168.1.203:50354
Sep  8 15:45:02 OpenWrt authpriv.notice dropbear[1421]: Password auth succeeded for 'root' from 192.168.1.203:50354

Z góry dziękuję za zainteresowanie i pomoc

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,074

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Używaj mojego openwrt czystego, nie będziesz miał problemu z zależnościami. I nie mieszaj oryginału (bo taki masz) z moim repo jeżeli chodzi o moduły kernela.

Sterownik option (potrzebny żeby /dev/ttyUSB0 istniało) domyślnie nie obsługuje tego modemu. Więc - używaj mojego softu.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez wokatorek

  • Zarejestrowany: 2014-07-03
  • Posty: 19

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Damn it, nie dojrzałem, że zmodyfikowanego OpenWRT też udostępniasz. Nawet doczytałem już uwagę o używaniu odpowiedniego repo dla odpowiedniego kernela. Czuję się jak kretyn (dużo czasu straciłem waląc głową w mur). Biorę się do roboty, dzięki za odpowiedź.

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,074

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Spoko smile

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez wokatorek

  • Zarejestrowany: 2014-07-03
  • Posty: 19

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Router łączy się przez modem, ale skrypt zwraca jeden błąd:

line 37: ip not found

Z czym jest to związane?

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,074

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Nie masz zainstalowanego pakietu ip

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez wokatorek

  • Zarejestrowany: 2014-07-03
  • Posty: 19

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Ok, znowu głupie pytanie i głupia odpowiedź. Czy pakiet i związana z nim komenda jest niezbędna do poprawnego działania połączenia? A może to, że działa teraz oznacza, że komenda ta jest zbędna?

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,074

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Jeżeli mówisz o tym moim skrypcie to była potrzebna do ustawienia routingu tylko.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez wokatorek

  • Zarejestrowany: 2014-07-03
  • Posty: 19

Odp: TL-WDR3600 v1.5 + Huawei 3276 + OpenWRT 12.09 - pomocy!

Ok, dzięki za całą pomoc! Temat do zamknięcia.