1

Temat: Tp-Link 1043+Problem z extrootem

Witam wszystkich. Czytuję to forum od dawna i już dość długo używam Gayrgole na moim 1043.

Od jakiegoś czasu miałem zrowbionego(w GUI) extroota, odpalone DLNA oraz FTP. Hub aktywny 3 peny (jeden do extrroota, dwa do danych). Wszystko sobie pięknie funkcjonowało do dziś. Dzieci jak zwykle oglądały bajkę przez DLNA nagle film się wyłączył. Zrobiłem ponowne skanowanie w GUI. To nie przyniosło rezultatu więc zapodałem reboot.

Po reboocie zniknął extroot i lipa. Router część ustawień zachował( klonowanie mac, DynDns, hasło).
Podłączałem tego pena bezpośrednio do routera ale to nic nie zmieniło.

Logread:

Jan  1 01:00:49 Gargoyle syslog.info syslogd started: BusyBox v1.19.4
Jan  1 01:00:49 Gargoyle kern.notice kernel: klogd started: BusyBox v1.19.4 (2014-05-24 21:29:35 CEST)
Jan  1 01:00:49 Gargoyle kern.notice kernel: [    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #54 Sat May 24 21:36:53 CEST 2014
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000] MyLoader: sysp=00000000, boardp=00000000, parts=00000000
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] bootconsole [early0] enabled
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] SoC: Atheros AR9132 rev 2
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Determined physical RAM map:
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000]  memory: 02000000 @ 00000000 (usable)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000] Zone PFN ranges:
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000]   Normal   0x00000000 -> 0x00002000
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000] Movable zone start PFN for each node
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000] Early memory PFN ranges
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000]     0: 0x00000000 -> 0x00002000
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000] On node 0 totalpages: 8192
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000] free_area_init_node: node 0, pgdat 802fdf20, node_mem_map 81000000
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000]   Normal zone: 64 pages used for memmap
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 01:00:49 Gargoyle kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Jan  1 01:00:49 Gargoyle kern.notice kernel: [    0.000000] Kernel command line:  board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 01:00:49 Gargoyle kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Memory: 28936k/32768k available (2256k kernel code, 3832k reserved, 425k data, 220k init, 0k highmem)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] NR_IRQS:51
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.080000] Mount-cache hash table entries: 512
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.090000] NET: Registered protocol family 16
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.100000] MIPS: machine is TP-LINK TL-WR1043ND
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.360000] bio: create slab <bio-0> at 0
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.370000] Switching to clocksource MIPS
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.380000] NET: Registered protocol family 2
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.390000] TCP: Hash tables configured (established 1024 bind 1024)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.400000] TCP reno registered
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:49 Gargoyle kern.info kernel: [    0.410000] NET: Registered protocol family 1
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.050000] usbcore: registered new interface driver ums-isd200
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.060000] usbcore: registered new interface driver ums-jumpshot
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.080000] usbcore: registered new interface driver ums-karma
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.090000] usbcore: registered new interface driver ums-sddr09
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.110000] usbcore: registered new interface driver ums-sddr55
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.120000] usbcore: registered new interface driver ums-usbat
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.140000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.400000] hub 1-1:1.0: USB hub found
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.400000] hub 1-1:1.0: 4 ports detected
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.700000] usb 1-1.4: new high-speed USB device number 3 using ehci-platform
Jan  1 01:00:49 Gargoyle kern.info kernel: [    9.840000] scsi0 : usb-storage 1-1.4:1.0
Jan  1 01:00:49 Gargoyle kern.notice kernel: [   10.840000] scsi 0:0:0:0: Direct-Access     Generic  Flash Disk       8.07 PQ: 0 ANSI: 2
Jan  1 01:00:49 Gargoyle kern.notice kernel: [   10.850000] sd 0:0:0:0: [sda] 1966080 512-byte logical blocks: (1.00 GB/960 MiB)
Jan  1 01:00:49 Gargoyle kern.notice kernel: [   10.860000] sd 0:0:0:0: [sda] Write Protect is off
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   10.860000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
Jan  1 01:00:49 Gargoyle kern.err kernel: [   10.870000] sd 0:0:0:0: [sda] No Caching mode page present
Jan  1 01:00:49 Gargoyle kern.err kernel: [   10.870000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan  1 01:00:49 Gargoyle kern.err kernel: [   10.880000] sd 0:0:0:0: [sda] No Caching mode page present
Jan  1 01:00:49 Gargoyle kern.err kernel: [   10.890000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan  1 01:00:49 Gargoyle kern.info kernel: [   11.160000]  sda: sda1 sda2
Jan  1 01:00:49 Gargoyle kern.err kernel: [   11.170000] sd 0:0:0:0: [sda] No Caching mode page present
Jan  1 01:00:49 Gargoyle kern.err kernel: [   11.170000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan  1 01:00:49 Gargoyle kern.notice kernel: [   11.180000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan  1 01:00:49 Gargoyle kern.info kernel: [   37.930000] eth0: link down
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.570000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.570000] Backport generated by backports.git backports-20140124-0-g1256d3e
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.750000] cfg80211: Calling CRDA to update world regulatory domain
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.760000] cfg80211: World regulatory domain updated:
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.760000] cfg80211:  DFS Master region: unset
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.770000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.780000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:49 Gargoyle kern.info kernel: [   38.780000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:49 Gargoyle kern.info kernel: [   39.080000] NET: Registered protocol family 10
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.460000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.460000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.460000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.460000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.460000] ath: Country alpha2 being used: US
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.460000] ath: Regpair used: 0x3a
Jan  1 01:00:49 Gargoyle kern.debug kernel: [   40.480000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.480000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.490000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.500000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.500000] cfg80211:  DFS Master region: unset
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.510000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.520000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.520000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.900000] RPC: Registered named UNIX socket transport module.
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.910000] RPC: Registered udp transport module.
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.920000] RPC: Registered tcp transport module.
Jan  1 01:00:49 Gargoyle kern.info kernel: [   40.920000] RPC: Registered tcp NFSv4.1 backchannel transport module.
Jan  1 01:00:49 Gargoyle kern.info kernel: [   41.490000] PPP generic driver version 2.4.2
Jan  1 01:00:49 Gargoyle kern.info kernel: [   41.640000] tun: Universal TUN/TAP device driver, 1.6
Jan  1 01:00:49 Gargoyle kern.info kernel: [   41.640000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan  1 01:00:56 Gargoyle user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:59 Gargoyle kern.debug kernel: [   59.620000] ar71xx: pll_reg 0xb8050014: 0x1a000000
Jan  1 01:00:59 Gargoyle daemon.notice netifd: Interface 'lan' is now up
Jan  1 01:00:59 Gargoyle daemon.notice netifd: Interface 'loopback' is now up
Jan  1 01:01:00 Gargoyle daemon.notice netifd: wan (983): udhcpc (v1.19.4) started
Jan  1 01:01:00 Gargoyle user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:01:00 Gargoyle daemon.notice netifd: wan (983): Sending discover...
Jan  1 01:01:00 Gargoyle kern.info kernel: [   59.920000] eth0: link up (1000Mbps/Full duplex)
Jan  1 01:01:00 Gargoyle kern.info kernel: [   59.930000] device eth0.1 entered promiscuous mode
Jan  1 01:01:00 Gargoyle kern.info kernel: [   59.930000] device eth0 entered promiscuous mode
Jan  1 01:01:00 Gargoyle kern.info kernel: [   59.940000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:01:00 Gargoyle kern.info kernel: [   59.940000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:01:00 Gargoyle kern.info kernel: [   60.920000] ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Jan  1 01:01:01 Gargoyle kern.info kernel: [   61.940000] br-lan: port 1(eth0.1) entered forwarding state
Jan  1 01:01:03 Gargoyle daemon.notice netifd: wan (983): Sending discover...
Jun 28 16:11:46 Gargoyle daemon.notice netifd: wan (983): Sending select for 213.156.109.XXX...
Jun 28 16:11:46 Gargoyle daemon.notice netifd: wan (983): Lease of 213.156.109.xxx
obtained, lease time 3600
Jun 28 16:11:46 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB_2.0_Hub Serial=?
Jun 28 16:11:47 Gargoyle daemon.notice netifd: Interface 'wan' is now up
Jun 28 16:11:47 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Generic Product=Mass_Storage Serial=95D2B46C
Jun 28 16:11:48 Gargoyle authpriv.info dropbear[1345]: Running in background
Jun 28 16:11:49 Gargoyle daemon.crit httpd_gargoyle[1379]: bind 0.0.0.0 - Address already in use
Jun 28 16:11:49 Gargoyle daemon.crit httpd_gargoyle[1379]: bind 0.0.0.0 - Address already in use
Jun 28 16:11:49 Gargoyle daemon.warn httpd_gargoyle[1386]: started as root without requesting chroot(), warning only
Jun 28 16:11:49 Gargoyle daemon.notice httpd_gargoyle[1386]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
Jun 28 18:12:59 Gargoyle cron.err crond[1206]: time disparity of 121 minutes detected
Jun 28 18:13:11 Gargoyle user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Success


Mount:

root@Gargoyle:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime,size=14580k)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)

blkid:

root@Gargoyle:~# blkid
/dev/mtdblock2: TYPE="squashfs"

Dodam, że nie jestem specjalnie Linuxowy zatem proszę o "przystępne" podpowiedzi smile

Pozdrawiam
Ryo

2

Odp: Tp-Link 1043+Problem z extrootem

Coś tam wykrywa, bo wydać patycje na starcie ale nie masz dalej. Przy uruchomionym routerze odłącz pendrive i podłącz jeszcze raz. Jeżeli się pokażą partycję  - sprawdź je przez  e2fsck -y /dev/sda1 czy jak tam partycję będziesz miał. Jak znajdzie (albo i nie) błędy i je naprawi to restartuj router z podłączonym już pendrivem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3

Odp: Tp-Link 1043+Problem z extrootem

Partycje się niestety nie pokazały.

4

Odp: Tp-Link 1043+Problem z extrootem

A co masz w logach?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

5 (edytowany przez Ryo 2014-06-28 18:18:41)

Odp: Tp-Link 1043+Problem z extrootem

Log:

Jun 28 19:00:14 Gargoyle daemon.info ddns_gargoyle[2698]:         Successfully retrieved local ip from url: http://checkip.org
Jun 28 19:00:34 Gargoyle kern.info kernel: [ 2934.850000] usb 1-1.4: USB disconnect, device number 3
Jun 28 19:00:42 Gargoyle kern.info kernel: [ 2943.030000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform
Jun 28 19:00:43 Gargoyle kern.info kernel: [ 2943.560000] scsi1 : usb-storage 1-1.4:1.0
Jun 28 19:00:43 Gargoyle user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Alcor_Micro Product=Mass_Storage_Device Serial=?
Jun 28 19:00:44 Gargoyle kern.notice kernel: [ 2944.560000] scsi 1:0:0:0: Direct-Access     Generic  USB Flash Disk   7.76 PQ: 0 ANSI: 2
Jun 28 19:00:44 Gargoyle kern.notice kernel: [ 2944.570000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Jun 28 19:02:17 Gargoyle authpriv.info dropbear[4185]: Child connection from 192.168.0.3:1396
Jun 28 19:02:41 Gargoyle authpriv.notice dropbear[4185]: Password auth succeeded for 'root' from 192.168.0.3:1396
Jun 28 19:12:45 Gargoyle daemon.notice netifd: wan (983): Sending renew...
Jun 28 19:12:45 Gargoyle daemon.notice netifd: wan (983): Lease of 213.156.109.xxx
obtained, lease time 3600
Jun 28 19:15:10 Gargoyle daemon.info ddns_gargoyle[2698]:         Successfully retrieved local ip from url: http://www.ip-address.org
Success

6

Odp: Tp-Link 1043+Problem z extrootem

Zainstaluj sobie fdiska i zrób fdisk -l /dev/sda

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

7

Odp: Tp-Link 1043+Problem z extrootem

Efektu brak hmm

root@Gargoyle:~# fdisk -l /dev/sda
root@Gargoyle:~#

8

Odp: Tp-Link 1043+Problem z extrootem

Podłącz pod komputer i przeformatuj go. Jeżeli się nie da to kup nowy pendrive.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

9

Odp: Tp-Link 1043+Problem z extrootem

Ok. Liczyłem, że się uda odzyskać zawartość smile Dzięki za poświęcony czas Cezary.

Pozdrawiam
Ryo

10

Odp: Tp-Link 1043+Problem z extrootem

Pamięci flash mają ograniczoną ilość cykli zapisu przypadającego na komórkę pamięci. Filesystemy jak extX bardzo dobrze sprawdzają się na normlanych dyskach ale nie za bardzo na flash. Szczególnie jeśli korzysta się z księgowania.
Używać się da ale przy częstych operacjach kasowania/zapisywania flash szybko się "starzeje".
Tym bardziej jeśli używa się księgowania. Dla pamięci flash zostały stworzone systemy jak JFFS2 czy YAFFS.
W których dba się o to by cała pamięć był "równomiernie' wykorzystana.

W przypadku ext może być tak że sektory na których odbywa się księgowanie są wielokrotnie częściej eksploatowane niż reszta pamięci i po pewnym czasie pojawiają się tam błędy co rzutuje na resztę partycji.

11

Odp: Tp-Link 1043+Problem z extrootem

Po podłączeniu pena do PC i odpaleniu Ubuntu pen nie był widoczny, odpaliłem XP z programem do montowania extX i pen się pojawił. Podłączyłem do TP-Linka i działa. smile

Czy idzie przenieść extroota na innego pena? Ten to Goodramowa relkamówka. Jak zrobić na takim penie rzeczone JFFS2 czy też YAFFS?


Pozdrawiam
Ryo

12

Odp: Tp-Link 1043+Problem z extrootem

Tam nie ma yaffs czy jffs. Normalnie zrób format na exta innego pendrive, skopiuj dane, później tylko w systemie zmień uuid.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

13

Odp: Tp-Link 1043+Problem z extrootem

A tak mie zaciekawił wykład Life-a smile I mnie Cezary na ziemię sprowadziłeś no... smile

14

Odp: Tp-Link 1043+Problem z extrootem

przecież obsługa jffs jest wkompilowana w jadro więc po co na silę używać extX?

15

Odp: Tp-Link 1043+Problem z extrootem

Ponieważ przedmówca miał już tam exta. Jak sobie będzie robił od początku to może sobie zrobić co i jak będzie chciał.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

16

Odp: Tp-Link 1043+Problem z extrootem

no ale kolega chce na nowo zrobić, tak zrozumiałem.

poza tym co za problem na nowym penie zrobić nowy filesystem (jffs) podmontować go oraz ten stary, skopiować co trzeba.
o ile da se kopiować ze starego pena

17

Odp: Tp-Link 1043+Problem z extrootem

Jeśli jffs jest lepszy od ext na flashu i najlepiej jest zrobić firstboota a następnie postawić wszystko od nowa to ja nie widzę przeskód. smile Jeśli mi podpowiecie jak to zrobić.