FAQ o OpenWrt | Sprzedam różne routery | Oddam

r_afaello · 2014-05-27 08:32:17

r_afaello
Użytkownik
Nieaktywny

Zarejestrowany: 2013-03-05
Posty: 69

Temat: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Witam.
Znowu mam awarie w tym routerku.
Pracował jako czytnik z temperatur. Extroot na pendrive. EXT2
Co 10 minut wykonywał skrypt odczytujący z digitempa temperaturę, wysyłał ją do MYSQL przez internet.
I to byłą cała jego praca.
2 dni tempu przestałem otrzymywać od niego dane.
Zalogowałem się do niego ale po niecałych 3 miutach mnie rozłączyło. I tak kilkanaście razy, za każdym razem ok 2-3 minut pracy i mnie rozłącza.
Sprawdziłem czy to router się wyłacza czy gubi sieć - fizycznie widać że się restartował.
nawet nie zdążałem zalogować się i przejrzeć logów.
Odłączyłem pena, podłączyłem pod innego linucha, zedytowałem plik system i zmieniłem na logowanie do pliku.

Jan  1 01:00:38 syslogd started: BusyBox v1.19.4
Jan  1 01:00:38 kernel: klogd started: BusyBox v1.19.4 (2014-01-10 15:52:30 CET)
Jan  1 01:00:38 kernel: [    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #7 Fri Jan 10 15:59:45 CET 2014
Jan  1 01:00:38 kernel: [    0.000000] bootconsole [early0] enabled
Jan  1 01:00:38 kernel: [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Jan  1 01:00:38 kernel: [    0.000000] SoC: Atheros AR9330 rev 1
Jan  1 01:00:38 kernel: [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Jan  1 01:00:38 kernel: [    0.000000] Determined physical RAM map:
Jan  1 01:00:38 kernel: [    0.000000]  memory: 02000000 @ 00000000 (usable)
Jan  1 01:00:38 kernel: [    0.000000] Initrd not found or empty - disabling initrd
Jan  1 01:00:38 kernel: [    0.000000] Zone PFN ranges:
Jan  1 01:00:38 kernel: [    0.000000]   Normal   0x00000000 -> 0x00002000
Jan  1 01:00:38 kernel: [    0.000000] Movable zone start PFN for each node
Jan  1 01:00:38 kernel: [    0.000000] Early memory PFN ranges
Jan  1 01:00:38 kernel: [    0.000000]     0: 0x00000000 -> 0x00002000
Jan  1 01:00:38 kernel: [    0.000000] On node 0 totalpages: 8192
Jan  1 01:00:38 kernel: [    0.000000] free_area_init_node: node 0, pgdat 802ed700, node_mem_map 81000000
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 64 pages used for memmap
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
Jan  1 01:00:38 kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 01:00:38 kernel: [    0.000000] pcpu-alloc: [0] 0 
Jan  1 01:00:38 kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Jan  1 01:00:38 kernel: [    0.000000] Kernel command line:  board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan  1 01:00:38 kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 01:00:38 kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan  1 01:00:38 kernel: [    0.000000] Writing ErrCtl register=00000000
Jan  1 01:00:38 kernel: [    0.000000] Readback ErrCtl register=00000000
Jan  1 01:00:38 kernel: [    0.000000] Memory: 29044k/32768k available (2224k kernel code, 3724k reserved, 391k data, 184k init, 0k highmem)
Jan  1 01:00:38 kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan  1 01:00:38 kernel: [    0.000000] NR_IRQS:51
Jan  1 01:00:38 kernel: [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan  1 01:00:38 kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Jan  1 01:00:38 kernel: [    0.080000] Mount-cache hash table entries: 512
Jan  1 01:00:38 kernel: [    0.090000] NET: Registered protocol family 16
Jan  1 01:00:38 kernel: [    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
Jan  1 01:00:38 kernel: [    0.100000] MIPS: machine is TP-LINK TL-MR3020
Jan  1 01:00:38 kernel: [    0.350000] bio: create slab <bio-0> at 0
Jan  1 01:00:38 kernel: [    0.360000] Switching to clocksource MIPS
Jan  1 01:00:38 kernel: [    8.330000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 01:00:38 kernel: [    8.330000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan  1 01:00:38 kernel: [    8.340000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan  1 01:00:38 kernel: [    8.380000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Jan  1 01:00:38 kernel: [    8.400000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Jan  1 01:00:38 kernel: [    8.400000] hub 1-0:1.0: USB hub found
Jan  1 01:00:38 kernel: [    8.400000] hub 1-0:1.0: 1 port detected
Jan  1 01:00:38 kernel: [    8.430000] Initializing USB Mass Storage driver...
Jan  1 01:00:38 kernel: [    8.430000] usbcore: registered new interface driver usb-storage
Jan  1 01:00:38 kernel: [    8.440000] USB Mass Storage support registered.
Jan  1 01:00:38 kernel: [    8.730000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan  1 01:00:38 kernel: [    8.890000] scsi0 : usb-storage 1-1:1.0
Jan  1 01:00:38 kernel: [    9.910000] scsi 0:0:0:0: Direct-Access     TOSHIBA  TransMemory      1.00 PQ: 0 ANSI: 4
Jan  1 01:00:38 kernel: [    9.920000] sd 0:0:0:0: [sda] 15148608 512-byte logical blocks: (7.75 GB/7.22 GiB)
Jan  1 01:00:38 kernel: [    9.930000] sd 0:0:0:0: [sda] Write Protect is off
Jan  1 01:00:38 kernel: [    9.930000] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
Jan  1 01:00:38 kernel: [    9.930000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan  1 01:00:38 kernel: [    9.950000]  sda: sda1 sda2
Jan  1 01:00:38 kernel: [    9.960000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan  1 01:00:38 kernel: [   30.470000] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
Jan  1 01:00:38 kernel: [   30.490000] EXT4-fs (sda2): warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 01:00:38 kernel: [   30.490000] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null)
Jan  1 01:00:38 kernel: [   30.710000] eth0: link down
Jan  1 01:00:38 kernel: [   31.300000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Jan  1 01:00:38 kernel: [   31.300000] Backport generated by backports.git backports-20130617-4-ge3220f5
Jan  1 01:00:38 kernel: [   31.500000] cfg80211: Calling CRDA to update world regulatory domain
Jan  1 01:00:38 kernel: [   31.500000] cfg80211: World regulatory domain updated:
Jan  1 01:00:38 kernel: [   31.510000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   31.510000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   31.520000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.530000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:38 kernel: [   32.530000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:38 kernel: [   32.530000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:38 kernel: [   32.530000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:38 kernel: [   32.530000] ath: Country alpha2 being used: US
Jan  1 01:00:38 kernel: [   32.530000] ath: Regpair used: 0x3a
Jan  1 01:00:38 kernel: [   32.540000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:38 kernel: [   32.540000] Registered led device: ath9k-phy0
Jan  1 01:00:38 kernel: [   32.540000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Jan  1 01:00:38 kernel: [   32.550000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:38 kernel: [   32.550000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:38 kernel: [   32.560000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   32.570000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.570000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.820000] PPP generic driver version 2.4.2
Jan  1 01:00:38 kernel: [   32.960000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:38 kernel: [   33.210000] NET: Registered protocol family 24
Jan  1 01:00:38 kernel: [   33.370000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Jan  1 01:00:38 kernel: [   34.170000] xt_time: kernel timezone is -0000
Jan  1 01:00:38 kernel: [   35.060000]     Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:38 kernel: [   35.060000]     Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:38 kernel: [   35.060000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:38 kernel: [   35.270000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:38 kernel: [   35.330000] ip_set: protocol 6
Jan  1 01:00:38 kernel: [   35.980000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:38 kernel: [   35.990000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:38 kernel: [   36.220000] usbcore: registered new interface driver usbserial
Jan  1 01:00:38 kernel: [   36.230000] USB Serial support registered for generic
Jan  1 01:00:38 kernel: [   36.230000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:38 kernel: [   36.240000] usbserial: USB Serial Driver core
Jan  1 01:00:38 kernel: [   36.290000] usbcore: registered new interface driver cdc_ether
Jan  1 01:00:38 kernel: [   36.330000] usbcore: registered new interface driver cdc_ncm
Jan  1 01:00:38 kernel: [   36.370000] USB Serial support registered for FTDI USB Serial Device
Jan  1 01:00:38 kernel: [   36.370000] usbcore: registered new interface driver ftdi_sio
Jan  1 01:00:38 kernel: [   36.380000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
Jan  1 01:00:38 kernel: [   36.500000] USB Serial support registered for GSM modem (1-port)
Jan  1 01:00:38 kernel: [   36.500000] usbcore: registered new interface driver option
Jan  1 01:00:38 kernel: [   36.510000] option: v0.7.2:USB Driver for GSM modems
Jan  1 01:00:38 kernel: [   36.620000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:38 kernel: [   36.630000] usbcore: registered new interface driver sierra
Jan  1 01:00:38 kernel: [   36.630000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:40 usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:41 usb-modeswitch: 1-1:1.0: Manufacturer=TOSHIBA Product=TransMemory Serial=CC52AF4C827ACD70E3C09135
Jan  1 01:00:44 kernel: [   44.670000] Adding 65532k swap on /dev/sda1.  Priority:-1 extents:1 across:65532k 
Jan  1 01:00:48 kernel: [   48.600000] device eth0 entered promiscuous mode
Jan  1 01:00:48 netifd: Interface 'lan' is now up
Jan  1 01:00:48 netifd: Interface 'loopback' is now up
Jan  1 01:00:48 firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:49 kernel: [   49.410000] eth0: link up (100Mbps/Full duplex)
Jan  1 01:00:49 kernel: [   49.410000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:49 kernel: [   49.420000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:51 kernel: [   51.420000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:51 sysinit: command failed: Device or resource busy (-16)
Jan  1 01:00:53 kernel: [   53.660000] device wlan0 entered promiscuous mode
Jan  1 01:00:54 kernel: [   54.160000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:54 kernel: [   54.160000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:56 kernel: [   56.160000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:57 netifd: Interface 'wan' is now up
Jan  1 01:00:59 kernel: [   59.140000] device wlan0-1 entered promiscuous mode
Jan  1 01:00:59 kernel: [   59.190000] br-lan: port 2(wlan0) entered disabled state
May 25 19:00:03 dropbear[1799]: Running in background
May 25 19:00:04 httpd_gargoyle[1826]: started as root without requesting chroot(), warning only
May 25 19:00:04 httpd_gargoyle[1826]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
May 25 19:00:05 dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
May 25 19:00:05 dnsmasq: Allowing 127.0.0.0/8 responses
May 25 19:00:08 dnsmasq[1880]: started, version 2.66 cachesize 150
May 25 19:00:08 dnsmasq[1880]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
May 25 19:00:08 dnsmasq-dhcp[1880]: DHCP, IP range 192.168.2.101 -- 192.168.2.110, lease time 12h
May 25 19:00:08 dnsmasq[1880]: using local addresses only for domain lan
May 25 19:00:08 dnsmasq[1880]: reading /tmp/resolv.conf.auto
May 25 19:00:08 dnsmasq[1880]: using nameserver 8.8.8.8#53
May 25 19:00:08 dnsmasq[1880]: using nameserver 8.8.8.8#53
May 25 19:00:08 dnsmasq[1880]: using local addresses only for domain lan
May 25 19:00:08 dnsmasq[1880]: read /etc/hosts - 2 addresses
May 25 19:00:08 dnsmasq-dhcp[1880]: read /etc/ethers - 0 addresses
May 25 19:00:09 sysinit: ERROR: No valid dynamic DNS service configurations defined
May 25 19:00:09 sysinit: (Did you specify correct configuration file path?)
May 25 19:00:09 sysinit: setting up led USB
May 25 19:00:09 sysinit: setting up led WLAN
May 25 19:00:09 sysinit: setting up led LAN
May 25 19:00:22 dnsmasq-dhcp[1880]: DHCPDISCOVER(br-lan) 192.168.2.139 00:1a:4b:59:22:2e 
May 25 19:00:22 dnsmasq-dhcp[1880]: DHCPOFFER(br-lan) 192.168.2.105 00:1a:4b:59:22:2e 
May 25 19:00:22 dnsmasq-dhcp[1880]: DHCPREQUEST(br-lan) 192.168.2.105 00:1a:4b:59:22:2e 
May 25 19:00:22 dnsmasq-dhcp[1880]: DHCPACK(br-lan) 192.168.2.105 00:1a:4b:59:22:2e laptop_hp
May 25 19:00:24 firewall: Reloading firewall due to ifup of wan (br-wan)
May 25 19:00:27 dropbear[2051]: Child connection from 192.168.2.105:3630
May 25 19:00:34 dropbear[2051]: Password auth succeeded for 'root' from 192.168.2.105:3630
Jan  1 01:00:38 syslogd started: BusyBox v1.19.4
Jan  1 01:00:38 kernel: klogd started: BusyBox v1.19.4 (2014-01-10 15:52:30 CET)
Jan  1 01:00:38 kernel: [    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #7 Fri Jan 10 15:59:45 CET 2014
Jan  1 01:00:38 kernel: [    0.000000] bootconsole [early0] enabled
Jan  1 01:00:38 kernel: [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Jan  1 01:00:38 kernel: [    0.000000] SoC: Atheros AR9330 rev 1
Jan  1 01:00:38 kernel: [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Jan  1 01:00:38 kernel: [    0.000000] Determined physical RAM map:
Jan  1 01:00:38 kernel: [    0.000000]  memory: 02000000 @ 00000000 (usable)
Jan  1 01:00:38 kernel: [    0.000000] Initrd not found or empty - disabling initrd
Jan  1 01:00:38 kernel: [    0.000000] Zone PFN ranges:
Jan  1 01:00:38 kernel: [    0.000000]   Normal   0x00000000 -> 0x00002000
Jan  1 01:00:38 kernel: [    0.000000] Movable zone start PFN for each node
Jan  1 01:00:38 kernel: [    0.000000] Early memory PFN ranges
Jan  1 01:00:38 kernel: [    0.000000]     0: 0x00000000 -> 0x00002000
Jan  1 01:00:38 kernel: [    0.000000] On node 0 totalpages: 8192
Jan  1 01:00:38 kernel: [    0.000000] free_area_init_node: node 0, pgdat 802ed700, node_mem_map 81000000
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 64 pages used for memmap
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
Jan  1 01:00:38 kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 01:00:38 kernel: [    0.000000] pcpu-alloc: [0] 0 
Jan  1 01:00:38 kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Jan  1 01:00:38 kernel: [    0.000000] Kernel command line:  board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan  1 01:00:38 kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 01:00:38 kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan  1 01:00:38 kernel: [    0.000000] Writing ErrCtl register=00000000
Jan  1 01:00:38 kernel: [    0.000000] Readback ErrCtl register=00000000
Jan  1 01:00:38 kernel: [    0.000000] Memory: 29044k/32768k available (2224k kernel code, 3724k reserved, 391k data, 184k init, 0k highmem)
Jan  1 01:00:38 kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan  1 01:00:38 kernel: [    0.000000] NR_IRQS:51
Jan  1 01:00:38 kernel: [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan  1 01:00:38 kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Jan  1 01:00:38 kernel: [    0.080000] Mount-cache hash table entries: 512
Jan  1 01:00:38 kernel: [    0.090000] NET: Registered protocol family 16
Jan  1 01:00:38 kernel: [    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
Jan  1 01:00:38 kernel: [    0.100000] MIPS: machine is TP-LINK TL-MR3020
Jan  1 01:00:38 kernel: [    0.350000] bio: create slab <bio-0> at 0
Jan  1 01:00:38 kernel: [    7.830000] usbcore: registered new interface driver hub
Jan  1 01:00:38 kernel: [    7.840000] usbcore: registered new device driver usb
Jan  1 01:00:38 kernel: [    8.310000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 01:00:38 kernel: [    8.320000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan  1 01:00:38 kernel: [    8.320000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan  1 01:00:38 kernel: [    8.360000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Jan  1 01:00:38 kernel: [    8.380000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Jan  1 01:00:38 kernel: [    8.380000] hub 1-0:1.0: USB hub found
Jan  1 01:00:38 kernel: [    8.380000] hub 1-0:1.0: 1 port detected
Jan  1 01:00:38 kernel: [    8.410000] Initializing USB Mass Storage driver...
Jan  1 01:00:38 kernel: [    8.410000] usbcore: registered new interface driver usb-storage
Jan  1 01:00:38 kernel: [    8.410000] USB Mass Storage support registered.
Jan  1 01:00:38 kernel: [    8.710000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan  1 01:00:38 kernel: [    8.870000] scsi0 : usb-storage 1-1:1.0
Jan  1 01:00:38 kernel: [    9.890000] scsi 0:0:0:0: Direct-Access     TOSHIBA  TransMemory      1.00 PQ: 0 ANSI: 4
Jan  1 01:00:38 kernel: [    9.900000] sd 0:0:0:0: [sda] 15148608 512-byte logical blocks: (7.75 GB/7.22 GiB)
Jan  1 01:00:38 kernel: [    9.910000] sd 0:0:0:0: [sda] Write Protect is off
Jan  1 01:00:38 kernel: [    9.910000] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
Jan  1 01:00:38 kernel: [    9.910000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan  1 01:00:38 kernel: [    9.930000]  sda: sda1 sda2
Jan  1 01:00:38 kernel: [    9.940000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan  1 01:00:38 kernel: [   30.440000] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
Jan  1 01:00:38 kernel: [   30.460000] EXT4-fs (sda2): warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 01:00:38 kernel: [   30.470000] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null)
Jan  1 01:00:38 kernel: [   30.680000] eth0: link down
Jan  1 01:00:38 kernel: [   31.270000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Jan  1 01:00:38 kernel: [   31.280000] Backport generated by backports.git backports-20130617-4-ge3220f5
Jan  1 01:00:38 kernel: [   31.460000] cfg80211: Calling CRDA to update world regulatory domain
Jan  1 01:00:38 kernel: [   31.460000] cfg80211: World regulatory domain updated:
Jan  1 01:00:38 kernel: [   31.470000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   31.480000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   31.480000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.510000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:38 kernel: [   32.510000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:38 kernel: [   32.510000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:38 kernel: [   32.510000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:38 kernel: [   32.510000] ath: Country alpha2 being used: US
Jan  1 01:00:38 kernel: [   32.510000] ath: Regpair used: 0x3a
Jan  1 01:00:38 kernel: [   32.510000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:38 kernel: [   32.520000] Registered led device: ath9k-phy0
Jan  1 01:00:38 kernel: [   32.520000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Jan  1 01:00:38 kernel: [   32.520000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:38 kernel: [   32.530000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:38 kernel: [   32.530000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   32.540000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.550000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.790000] PPP generic driver version 2.4.2
Jan  1 01:00:38 kernel: [   32.940000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:38 kernel: [   33.190000] NET: Registered protocol family 24
Jan  1 01:00:38 kernel: [   33.350000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Jan  1 01:00:38 kernel: [   34.150000] xt_time: kernel timezone is -0000
Jan  1 01:00:38 kernel: [   35.040000]     Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:38 kernel: [   35.040000]     Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:38 kernel: [   35.050000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:38 kernel: [   35.250000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:38 kernel: [   35.310000] ip_set: protocol 6
Jan  1 01:00:38 kernel: [   35.970000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:38 kernel: [   35.970000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:38 kernel: [   36.210000] usbcore: registered new interface driver usbserial
Jan  1 01:00:38 kernel: [   36.210000] USB Serial support registered for generic
Jan  1 01:00:38 kernel: [   36.220000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:38 kernel: [   36.220000] usbserial: USB Serial Driver core
Jan  1 01:00:38 kernel: [   36.270000] usbcore: registered new interface driver cdc_ether
Jan  1 01:00:38 kernel: [   36.320000] usbcore: registered new interface driver cdc_ncm
Jan  1 01:00:38 kernel: [   36.350000] USB Serial support registered for FTDI USB Serial Device
Jan  1 01:00:38 kernel: [   36.360000] usbcore: registered new interface driver ftdi_sio
Jan  1 01:00:38 kernel: [   36.360000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
Jan  1 01:00:38 kernel: [   36.480000] USB Serial support registered for GSM modem (1-port)
Jan  1 01:00:38 kernel: [   36.490000] usbcore: registered new interface driver option
Jan  1 01:00:38 kernel: [   36.490000] option: v0.7.2:USB Driver for GSM modems
Jan  1 01:00:38 kernel: [   36.610000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:38 kernel: [   36.610000] usbcore: registered new interface driver sierra
Jan  1 01:00:38 kernel: [   36.620000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:40 usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:41 usb-modeswitch: 1-1:1.0: Manufacturer=TOSHIBA Product=TransMemory Serial=CC52AF4C827ACD70E3C09135
Jan  1 01:00:43 kernel: [   43.290000] Adding 65532k swap on /dev/sda1.  Priority:-1 extents:1 across:65532k 
Jan  1 01:00:47 kernel: [   47.000000] device eth0 entered promiscuous mode
Jan  1 01:00:47 netifd: Interface 'lan' is now up
Jan  1 01:00:47 netifd: Interface 'loopback' is now up
Jan  1 01:00:47 kernel: [   47.400000] eth0: link up (100Mbps/Full duplex)
Jan  1 01:00:47 kernel: [   47.400000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:47 kernel: [   47.410000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:47 firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:49 kernel: [   49.410000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:50 sysinit: command failed: Device or resource busy (-16)
Jan  1 01:00:51 kernel: [   51.970000] device wlan0 entered promiscuous mode
Jan  1 01:00:52 kernel: [   52.580000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:52 kernel: [   52.580000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:54 kernel: [   54.580000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:55 netifd: Interface 'wan' is now up
Jan  1 01:00:57 kernel: [   57.240000] br-lan: port 2(wlan0) entered disabled state
Jan  1 01:00:57 kernel: [   57.550000] device wlan0-1 entered promiscuous mode
May 25 19:00:03 dropbear[1785]: Running in background
May 25 19:00:04 httpd_gargoyle[1826]: started as root without requesting chroot(), warning only
May 25 19:00:04 httpd_gargoyle[1826]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
May 25 19:00:05 dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
May 25 19:00:05 dnsmasq: Allowing 127.0.0.0/8 responses
May 25 19:00:08 dnsmasq[1880]: started, version 2.66 cachesize 150
May 25 19:00:08 dnsmasq[1880]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
May 25 19:00:08 dnsmasq-dhcp[1880]: DHCP, IP range 192.168.2.101 -- 192.168.2.110, lease time 12h
May 25 19:00:08 dnsmasq[1880]: using local addresses only for domain lan
May 25 19:00:08 dnsmasq[1880]: reading /tmp/resolv.conf.auto
May 25 19:00:08 dnsmasq[1880]: using nameserver 8.8.8.8#53
May 25 19:00:08 dnsmasq[1880]: using nameserver 8.8.8.8#53
May 25 19:00:08 dnsmasq[1880]: using local addresses only for domain lan
May 25 19:00:08 dnsmasq[1880]: read /etc/hosts - 2 addresses
May 25 19:00:08 dnsmasq-dhcp[1880]: read /etc/ethers - 0 addresses
May 25 19:00:08 sysinit: ERROR: No valid dynamic DNS service configurations defined
May 25 19:00:08 sysinit: (Did you specify correct configuration file path?)
May 25 19:00:09 sysinit: setting up led USB
May 25 19:00:09 sysinit: setting up led WLAN
May 25 19:00:09 sysinit: setting up led LAN
May 25 19:00:15 dnsmasq-dhcp[1880]: DHCPDISCOVER(br-lan) 192.168.2.105 00:1a:4b:59:22:2e 
May 25 19:00:15 dnsmasq-dhcp[1880]: DHCPOFFER(br-lan) 192.168.2.105 00:1a:4b:59:22:2e 
May 25 19:00:15 dnsmasq-dhcp[1880]: DHCPREQUEST(br-lan) 192.168.2.105 00:1a:4b:59:22:2e 
May 25 19:00:15 dnsmasq-dhcp[1880]: DHCPACK(br-lan) 192.168.2.105 00:1a:4b:59:22:2e laptop_hp
May 25 19:00:17 dropbear[1924]: Child connection from 192.168.2.105:3653
May 25 19:00:24 firewall: Reloading firewall due to ifup of wan (br-wan)
May 25 19:00:25 dropbear[1924]: Bad password attempt for 'root' from 192.168.2.105:3653
May 25 19:00:31 dropbear[1924]: Password auth succeeded for 'root' from 192.168.2.105:3653
Jan  1 01:00:38 syslogd started: BusyBox v1.19.4
Jan  1 01:00:38 kernel: klogd started: BusyBox v1.19.4 (2014-01-10 15:52:30 CET)
Jan  1 01:00:38 kernel: [    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #7 Fri Jan 10 15:59:45 CET 2014
Jan  1 01:00:38 kernel: [    0.000000] bootconsole [early0] enabled
Jan  1 01:00:38 kernel: [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Jan  1 01:00:38 kernel: [    0.000000] SoC: Atheros AR9330 rev 1
Jan  1 01:00:38 kernel: [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Jan  1 01:00:38 kernel: [    0.000000] Determined physical RAM map:
Jan  1 01:00:38 kernel: [    0.000000]  memory: 02000000 @ 00000000 (usable)
Jan  1 01:00:38 kernel: [    0.000000] Initrd not found or empty - disabling initrd
Jan  1 01:00:38 kernel: [    0.000000] Zone PFN ranges:
Jan  1 01:00:38 kernel: [    0.000000]   Normal   0x00000000 -> 0x00002000
Jan  1 01:00:38 kernel: [    0.000000] Movable zone start PFN for each node
Jan  1 01:00:38 kernel: [    0.000000] Early memory PFN ranges
Jan  1 01:00:38 kernel: [    0.000000]     0: 0x00000000 -> 0x00002000
Jan  1 01:00:38 kernel: [    0.000000] On node 0 totalpages: 8192
Jan  1 01:00:38 kernel: [    0.000000] free_area_init_node: node 0, pgdat 802ed700, node_mem_map 81000000
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 64 pages used for memmap
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan  1 01:00:38 kernel: [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
Jan  1 01:00:38 kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 01:00:38 kernel: [    0.000000] pcpu-alloc: [0] 0 
Jan  1 01:00:38 kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Jan  1 01:00:38 kernel: [    0.000000] Kernel command line:  board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan  1 01:00:38 kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 01:00:38 kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 01:00:38 kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan  1 01:00:38 kernel: [    0.000000] Writing ErrCtl register=00000000
Jan  1 01:00:38 kernel: [    0.000000] Readback ErrCtl register=00000000
Jan  1 01:00:38 kernel: [    0.000000] Memory: 29044k/32768k available (2224k kernel code, 3724k reserved, 391k data, 184k init, 0k highmem)
Jan  1 01:00:38 kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan  1 01:00:38 kernel: [    0.000000] NR_IRQS:51
Jan  1 01:00:38 kernel: [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan  1 01:00:38 kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Jan  1 01:00:38 kernel: [    0.080000] Mount-cache hash table entries: 512
Jan  1 01:00:38 kernel: [    0.090000] NET: Registered protocol family 16
Jan  1 01:00:38 kernel: [    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
Jan  1 01:00:38 kernel: [    0.100000] MIPS: machine is TP-LINK TL-MR3020
Jan  1 01:00:38 kernel: [    0.350000] bio: create slab <bio-0> at 0
Jan  1 01:00:38 kernel: [    7.850000] usbcore: registered new interface driver hub
Jan  1 01:00:38 kernel: [    7.860000] usbcore: registered new device driver usb
Jan  1 01:00:38 kernel: [    8.340000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan  1 01:00:38 kernel: [    8.340000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan  1 01:00:38 kernel: [    8.350000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan  1 01:00:38 kernel: [    8.390000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Jan  1 01:00:38 kernel: [    8.410000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Jan  1 01:00:38 kernel: [    8.410000] hub 1-0:1.0: USB hub found
Jan  1 01:00:38 kernel: [    8.410000] hub 1-0:1.0: 1 port detected
Jan  1 01:00:38 kernel: [    8.440000] Initializing USB Mass Storage driver...
Jan  1 01:00:38 kernel: [    8.440000] usbcore: registered new interface driver usb-storage
Jan  1 01:00:38 kernel: [    8.450000] USB Mass Storage support registered.
Jan  1 01:00:38 kernel: [    8.740000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan  1 01:00:38 kernel: [    8.900000] scsi0 : usb-storage 1-1:1.0
Jan  1 01:00:38 kernel: [    9.920000] scsi 0:0:0:0: Direct-Access     TOSHIBA  TransMemory      1.00 PQ: 0 ANSI: 4
Jan  1 01:00:38 kernel: [    9.930000] sd 0:0:0:0: [sda] 15148608 512-byte logical blocks: (7.75 GB/7.22 GiB)
Jan  1 01:00:38 kernel: [    9.940000] sd 0:0:0:0: [sda] Write Protect is off
Jan  1 01:00:38 kernel: [    9.940000] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00
Jan  1 01:00:38 kernel: [    9.940000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan  1 01:00:38 kernel: [    9.960000]  sda: sda1 sda2
Jan  1 01:00:38 kernel: [    9.970000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan  1 01:00:38 kernel: [   30.470000] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
Jan  1 01:00:38 kernel: [   30.490000] EXT4-fs (sda2): warning: mounting unchecked fs, running e2fsck is recommended
Jan  1 01:00:38 kernel: [   30.500000] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null)
Jan  1 01:00:38 kernel: [   30.710000] eth0: link down
Jan  1 01:00:38 kernel: [   31.300000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Jan  1 01:00:38 kernel: [   31.310000] Backport generated by backports.git backports-20130617-4-ge3220f5
Jan  1 01:00:38 kernel: [   31.490000] cfg80211: Calling CRDA to update world regulatory domain
Jan  1 01:00:38 kernel: [   31.500000] cfg80211: World regulatory domain updated:
Jan  1 01:00:38 kernel: [   31.500000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   31.510000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   31.520000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.540000] ath: EEPROM regdomain: 0x0
Jan  1 01:00:38 kernel: [   32.540000] ath: EEPROM indicates default country code should be used
Jan  1 01:00:38 kernel: [   32.540000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:38 kernel: [   32.540000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:38 kernel: [   32.540000] ath: Country alpha2 being used: US
Jan  1 01:00:38 kernel: [   32.540000] ath: Regpair used: 0x3a
Jan  1 01:00:38 kernel: [   32.540000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:38 kernel: [   32.550000] Registered led device: ath9k-phy0
Jan  1 01:00:38 kernel: [   32.550000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Jan  1 01:00:38 kernel: [   32.550000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:38 kernel: [   32.560000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:38 kernel: [   32.560000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   32.570000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.580000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.820000] PPP generic driver version 2.4.2
Jan  1 01:00:38 kernel: [   32.970000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:38 kernel: [   33.220000] NET: Registered protocol family 24
Jan  1 01:00:38 kernel: [   33.380000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Jan  1 01:00:38 kernel: [   34.180000] xt_time: kernel timezone is -0000
Jan  1 01:00:38 kernel: [   35.070000]     Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:38 kernel: [   35.070000]     Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:38 kernel: [   35.080000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:38 kernel: [   35.280000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:38 kernel: [   35.340000] ip_set: protocol 6
Jan  1 01:00:38 kernel: [   36.000000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:38 kernel: [   36.000000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:38 kernel: [   36.240000] usbcore: registered new interface driver usbserial
Jan  1 01:00:38 kernel: [   36.240000] USB Serial support registered for generic
Jan  1 01:00:38 kernel: [   36.250000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:38 kernel: [   36.250000] usbserial: USB Serial Driver core
Jan  1 01:00:38 kernel: [   36.300000] usbcore: registered new interface driver cdc_ether
Jan  1 01:00:38 kernel: [   36.350000] usbcore: registered new interface driver cdc_ncm
Jan  1 01:00:38 kernel: [   36.380000] USB Serial support registered for FTDI USB Serial Device
Jan  1 01:00:38 kernel: [   36.390000] usbcore: registered new interface driver ftdi_sio
Jan  1 01:00:38 kernel: [   36.390000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
Jan  1 01:00:38 kernel: [   36.510000] USB Serial support registered for GSM modem (1-port)
Jan  1 01:00:38 kernel: [   36.520000] usbcore: registered new interface driver option
Jan  1 01:00:38 kernel: [   36.520000] option: v0.7.2:USB Driver for GSM modems
Jan  1 01:00:38 kernel: [   36.640000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:38 kernel: [   36.640000] usbcore: registered new interface driver sierra
Jan  1 01:00:38 kernel: [   36.650000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:40 usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:41 usb-modeswitch: 1-1:1.0: Manufacturer=TOSHIBA Product=TransMemory Serial=CC52AF4C827ACD70E3C09135
Jan  1 01:00:41 kernel: [   41.930000] Adding 65532k swap on /dev/sda1.  Priority:-1 extents:1 across:65532k 
Jan  1 01:00:45 kernel: [   45.550000] device eth0 entered promiscuous mode
Jan  1 01:00:45 netifd: Interface 'lan' is now up
Jan  1 01:00:45 netifd: Interface 'loopback' is now up
Jan  1 01:00:45 firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:46 kernel: [   46.540000] eth0: link up (100Mbps/Full duplex)
Jan  1 01:00:46 kernel: [   46.540000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:46 kernel: [   46.550000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:48 kernel: [   48.550000] br-lan: port 1(eth0) entered forwarding state
Jan  1 01:00:48 sysinit: command failed: Device or resource busy (-16)
Jan  1 01:00:50 kernel: [   50.440000] device wlan0 entered promiscuous mode
Jan  1 01:00:51 kernel: [   51.010000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:51 kernel: [   51.010000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:53 kernel: [   53.010000] br-lan: port 2(wlan0) entered forwarding state
Jan  1 01:00:54 netifd: Interface 'wan' is now up
Jan  1 01:00:54 kernel: [   54.690000] br-lan: port 2(wlan0) entered disabled state
Jan  1 01:00:55 kernel: [   55.890000] device wlan0-1 entered promiscuous mode

Niewiele mi to powiedziało (jestem laikiem).
Zajrzałem do zawartości atalogów /etc/init.d i co się okazało o ile w /etc/config wyglądało wszystko na oryginalne to w init.d były tylko 3 pliki.
Miałem wcześniej zrobiona kopię katalogu więc wrzuciłem. Restart i obserwacja. Niestety bez zmian.
Jak miałem podłączony ten pendrive pod inny router to zrobiłem e2fsck. Znalazł błędy (niestety nie zapisałem jakie) i je naprawił.

Teraz zaktualizowałem soft w tym MR3020 i od nowa go konfiguruje do pełnienia swojej roli. (temperatury).
Tym razem chciałbym żeby na tym penie była także baza mysql (mógłbym spokojnie wyłączyć swój domowy bez obawy że nie będzie odczytów) .

No i przechodzimy do meritum.
Domyślam się że problemem jest brak możliwości przy reboocie (np. raz dziennie) przeprowadzenia fsck.
Skoro e2fsprogs jest zainstalowany na extroocie bo niema miejsca w pam wewnetrznej to jak ma się sam zeskanować mimo wpisów w fstabie.
Noi i teraz prośba.
Po aktualizacji, nic jeszcze nie wgrywane mam tyle miejsca:

Filesystem                Size      Used Available Use% Mounted on
rootfs                  320.0K    244.0K     76.0K  76% /
/dev/root                 2.8M      2.8M         0 100% /rom
tmpfs                    14.3M    548.0K     13.7M   4% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/mtdblock3          320.0K    244.0K     76.0K  76% /overlay
overlayfs:/overlay      320.0K    244.0K     76.0K  76% /
/dev/sda2                 7.0G     19.3M      7.0G   0% /mnt/sda2

Jak wrzucić tutaj fsck, opkg przy prubie instalacji e2fsprogs wypluwa że mam za mało miejsca. Można jakoś wyłuskać samo fsck ? (zaznaczam ze sam nic nie skompiluję bo nie umiem).

Pyt 2. Czy bezpiecnziej będzie sformatować go np na ext3 lub 4 ?

Cezary · 2014-05-27 08:43:57

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,793

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Nie da się. Samo fsck zajmuje też dużo miejsca, więc nic z tego. Do /tmp możesz zainstalować, ale to oczywiście nic nie da po resecie.

Pisz do pepe2k żeby Ci pamięć na większą wymienił.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

r_afaello · 2014-05-27 09:05:13

r_afaello
Użytkownik
Nieaktywny

Zarejestrowany: 2013-03-05
Posty: 69

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Dzięki.
Docelowo pewnie tak zrobię (już raz korzystałem z pomocy kolegi i jestem zadowolony) doraźnie myślałem że da się coś wykombinować.

A odnośnie formatowania możesz podpowiedzieć coś? (system plikó)

Cezary · 2014-05-27 09:06:11

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,793

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Zainstaluj czysty soft bez gui, nie gargoyle. Tam jest więcej miejsca wolnego.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

r_afaello · 2014-05-28 17:06:14

r_afaello
Użytkownik
Nieaktywny

Zarejestrowany: 2013-03-05
Posty: 69

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Dobra. Przywiązałem się do tego softu wiec dam jeszcze jedną szansę dla tego rozwiązania ext2 bez fsck na starcie.
Skonfigurowałem odpaliłem i działa puki co.
No ale niema tak dobrze.
Sprawdzam rano na logi z odczytów temperatur które lądują u mnie - wszystko ok.
Sprawdzam za jakiś czas - kiszka. Ok 7:40 ostatni odczyt.
Próbuje zalogować się (putty) na router. Nie ma połączenia.
(Mój router pracuje jako Klient+AP, net otrzymuje z innego routera (nazwijmy go router2 do którego użyczono mi dostęp) przez wifi. Sam też nadaje wifi.)

Sprawdzam połączenie z routerem będącym "oknem na świat" dla mojego mr3020. Widzę go, mogę się zalogować wszystko jest OK. Wykonuję jego reboot. Nic to nie daje. Dalej brak widoczności MR3020.

Wracam z pracy. Idę obejrzeć ofiarę. laptop się odpala a ja w między czasie sprawdzam w telefonie sieci wifi w zasięgu.
Widzę router2 - sygnał ok 30%, sygnału z MR3020 brak. Jakby wyłączone wifi było.
Podłączam kabel, otrzymuję adres z dhcp. Loguję się przez putty - połączenie jest. Gui też działa.
Robię ping bramy (router2) brak odpowiedzi. Przeglądam logi, brak wpisów z godziny kiedy przestał działać net.
Ale zauważyłem że w laptopie aktualizować zaczął się antywirus. Skąd ten net?
Robię ping routera2 jeszcze raz - wszystko działa. Pinguję google.pl - też ok.
Sprawdzam w telefonieu obecne w okolicy sieci - pojawił się mój mr3020. \
Nie robiłem żadnego restartu a jedynie pingnąłem praę razy . Tak jakby nadajnik sie wyłaczył a ja go obudziłem.
Sprawdziłem w gui harmonogram wifi - wyłączony.

Co to może być?

Ps. Pisze powyższą wiadomość i w miedzy czasie (już z domu, zdalnie) wlazłem w /config/system żeby zmienić logi na zapis do pliku. Ustawiłem

option log_type 'file'
option log_file '/mnt/logi.log
option log_size '512'

No i zrobiłem restart. Po restarcie sprawdzam - plik logów się nie utworzył. Wchodzę w plik system i sprawdzam- rzeczywiście mój błąd - nie postawiłem apostrofu na końcu logi.log.
Poprawiam, restartuję.
Po reboocie wchodzę w gui a tu - kiszka strona wygląda jak dokument tekstowy i na samej górze napisanuy błąd :
ERROR: no system package defined!
Wchodzę w putty, robię reboot.
Czekam kilka minut - brak łączności. pytty - connection time out.

Pofatyguje (mam moze ze 200m) do router i zobaczę czy działa. Jak juzbędę przy nim to co sprawdzić, jak naprawić gui (pytam żeby ciągle nie biegać)?

Cezary · 2014-05-28 17:12:33

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,793

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

ERROR: no system package defined!

To znaczy że /etc/config/gargoyle zepsułeś.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

r_afaello · 2014-05-28 17:33:21

r_afaello
Użytkownik
Nieaktywny

Zarejestrowany: 2013-03-05
Posty: 69

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Właśnie jestem w kotłowni.
Po podpięciu kablem.
wifi brak.
po wpisaniu polecenie wifi od razu się pojawiło i net hula jak trzeba.

BusyBox v1.19.4 (2014-05-24 20:34:56 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.


             _____                             _
            |  __ \                           | |
            | |  \/ __ _ _ __ __ _  ___  _   _| | ___
            | | __ / _` | '__/ _` |/ _ \| | | | |/ _ \
            | |_\ \ (_| | | | (_| | (_) | |_| | |  __/
             \____/\__,_|_|  \__, |\___/ \__, |_|\___|
                              __/ |       __/ |
                             |___/       |___/

 ----------------------------------------------------------------
 |                                                              |
 | Gargoyle PL 1.6.1.2 (fab07c8)                                |
 | OpenWrt Attitude Adjustment 12.09.1 (r40835)                 |
 | Build time: 2014-05-24 20:34 CEST                            |
 |                                                              |
 | Cezary Jackiewicz (obsy), http://eko.one.pl                  |
 | Start systemu z pendriva                                     |
 ----------------------------------------------------------------
 | Machine: TP-Link TL-MR3020 v1                                |
 | Uptime: 0d, 00:32:30                                         |
 | Load: 0.05 0.03 0.05                                         |
 | Flash: total: 7.0GB, free: 7.0GB, used: 0%                   |
 | Memory: total: 28.5MB, free: 10.6MB, used: 62%               |
 | WAN: 192.168.1.100, proto: dhcp                              |
 | LAN: 192.168.2.100                                           |
 | WLAN: mode: ap, ssid: GargoyleKOT, channel: 6, conn: 0       |
 | WLAN: mode: sta, ssid: TP-LINK_9A902C, channel: 6, conn: 0   |
 ----------------------------------------------------------------
root@Gargoyle:~# wifi
command failed: Device or resource busy (-16)
Configuration file: /var/run/hostapd-phy0.conf
Using interface wlan0 with hwaddr 64:66:b3:ba:f5:28 and ssid "GargoyleKOT"
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
Successfully initialized wpa_supplicant
root@Gargoyle:~#

Sprawdzam gui - działa - a restartu nie było.

zapisy z logu

Jan  1 01:00:37 syslogd started: BusyBox v1.19.4
Jan  1 01:00:37 kernel: klogd started: BusyBox v1.19.4 (2014-05-24 20:34:56 CEST)
Jan  1 01:00:37 kernel: [    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #50 Sat May 24 20:42:22 CEST 2014
Jan  1 01:00:37 kernel: [    0.000000] bootconsole [early0] enabled
Jan  1 01:00:37 kernel: [    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Jan  1 01:00:37 kernel: [    0.000000] SoC: Atheros AR9330 rev 1
Jan  1 01:00:37 kernel: [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
Jan  1 01:00:37 kernel: [    0.000000] Determined physical RAM map:
Jan  1 01:00:37 kernel: [    0.000000]  memory: 02000000 @ 00000000 (usable)
Jan  1 01:00:37 kernel: [    0.000000] Initrd not found or empty - disabling initrd
Jan  1 01:00:37 kernel: [    0.000000] Zone PFN ranges:
Jan  1 01:00:37 kernel: [    0.000000]   Normal   0x00000000 -> 0x00002000
Jan  1 01:00:37 kernel: [    0.000000] Movable zone start PFN for each node
Jan  1 01:00:37 kernel: [    0.000000] Early memory PFN ranges
Jan  1 01:00:37 kernel: [    0.000000]     0: 0x00000000 -> 0x00002000
Jan  1 01:00:37 kernel: [    0.000000] On node 0 totalpages: 8192
Jan  1 01:00:37 kernel: [    0.000000] free_area_init_node: node 0, pgdat 802ed700, node_mem_map 81000000
Jan  1 01:00:37 kernel: [    0.000000]   Normal zone: 64 pages used for memmap
Jan  1 01:00:37 kernel: [    0.000000]   Normal zone: 0 pages reserved
Jan  1 01:00:37 kernel: [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
Jan  1 01:00:37 kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jan  1 01:00:37 kernel: [    0.000000] pcpu-alloc: [0] 0 
Jan  1 01:00:37 kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Jan  1 01:00:37 kernel: [    0.000000] Kernel command line:  board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan  1 01:00:37 kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jan  1 01:00:37 kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan  1 01:00:37 kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan  1 01:00:37 kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan  1 01:00:37 kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan  1 01:00:37 kernel: [    0.000000] Writing ErrCtl register=00000000
Jan  1 01:00:37 kernel: [    0.000000] Readback ErrCtl register=00000000
Jan  1 01:00:37 kernel: [    0.000000] Memory: 29044k/32768k available (2224k kernel code, 3724k reserved, 391k data, 184k init, 0k highmem)
Jan  1 01:00:37 kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan  1 01:00:37 kernel: [    0.000000] NR_IRQS:51
Jan  1 01:00:37 kernel: [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan  1 01:00:37 kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Jan  1 01:00:38 kernel: [    0.080000] Mount-cache hash table entries: 512
Jan  1 01:00:38 kernel: [    0.090000] NET: Registered protocol family 16
Jan  1 01:00:38 kernel: [    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
Jan  1 01:00:38 kernel: [    0.100000] MIPS: machine is TP-LINK TL-MR3020
Jan  1 01:00:38 kernel: [    0.350000] bio: create slab <bio-0> at 0
Jan  1 01:00:38 kernel: [    0.360000] Switching to clocksource MIPS
Jan  1 01:00:38 kernel: [    0.360000] NET: Registered protocol family 2
Jan  1 01:00:38 kernel: [    0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 01:00:38 kernel: [    0.370000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
Jan  1 01:00:38 kernel: [    0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Jan  1 01:00:38 kernel: [    0.380000] TCP: Hash tables configured (established 1024 bind 1024)
Jan  1 01:00:38 kernel: [    0.390000] TCP reno registered
Jan  1 01:00:38 kernel: [    0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:38 kernel: [    0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jan  1 01:00:38 kernel: [    0.400000] NET: Registered protocol family 1
Jan  1 01:00:38 kernel: [    0.410000] PCI: CLS 0 bytes, default 32
Jan  1 01:00:38 kernel: [    0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jan  1 01:00:38 kernel: [    0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jan  1 01:00:38 kernel: [    0.440000] msgmni has been set to 56
Jan  1 01:00:38 kernel: [    0.440000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Jan  1 01:00:38 kernel: [    0.450000] io scheduler noop registered
Jan  1 01:00:38 kernel: [    0.450000] io scheduler deadline registered (default)
Jan  1 01:00:38 kernel: [    0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Jan  1 01:00:38 kernel: [    0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Jan  1 01:00:38 kernel: [    0.480000] console [ttyATH0] enabled, bootconsole disabled
Jan  1 01:00:38 kernel: [    0.490000] m25p80 spi0.0: found s25sl032a, expected m25p80
Jan  1 01:00:38 kernel: [    0.490000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
Jan  1 01:00:38 kernel: [    0.500000] 5 tp-link partitions found on MTD device spi0.0
Jan  1 01:00:38 kernel: [    0.510000] Creating 5 MTD partitions on "spi0.0":
Jan  1 01:00:38 kernel: [    0.510000] 0x000000000000-0x000000020000 : "u-boot"
Jan  1 01:00:38 kernel: [    0.520000] 0x000000020000-0x0000001096e0 : "kernel"
Jan  1 01:00:38 kernel: [    0.520000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:38 kernel: [    0.530000] 0x0000001096e0-0x0000003f0000 : "rootfs"
Jan  1 01:00:38 kernel: [    0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jan  1 01:00:38 kernel: [    0.550000] mtd: partition "rootfs" set to be root filesystem
Jan  1 01:00:38 kernel: [    0.560000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=50000 
Jan  1 01:00:38 kernel: [    0.560000] 0x0000003a0000-0x0000003f0000 : "rootfs_data"
Jan  1 01:00:38 kernel: [    0.570000] 0x0000003f0000-0x000000400000 : "art"
Jan  1 01:00:38 kernel: [    0.580000] 0x000000020000-0x0000003f0000 : "firmware"
Jan  1 01:00:38 kernel: [    0.600000] ag71xx_mdio: probed
Jan  1 01:00:38 kernel: [    0.600000] eth0: Atheros AG71xx at 0xb9000000, irq 4
Jan  1 01:00:38 kernel: [    1.160000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Jan  1 01:00:38 kernel: [   32.500000] ath: doing EEPROM country->regdmn map search
Jan  1 01:00:38 kernel: [   32.500000] ath: country maps to regdmn code: 0x3a
Jan  1 01:00:38 kernel: [   32.500000] ath: Country alpha2 being used: US
Jan  1 01:00:38 kernel: [   32.500000] ath: Regpair used: 0x3a
Jan  1 01:00:38 kernel: [   32.510000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan  1 01:00:38 kernel: [   32.510000] Registered led device: ath9k-phy0
Jan  1 01:00:38 kernel: [   32.510000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Jan  1 01:00:38 kernel: [   32.530000] cfg80211: Calling CRDA for country: US
Jan  1 01:00:38 kernel: [   32.530000] cfg80211: Regulatory domain changed to country: US
Jan  1 01:00:38 kernel: [   32.530000] cfg80211:  DFS Master region: unset
Jan  1 01:00:38 kernel: [   32.540000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan  1 01:00:38 kernel: [   32.550000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.550000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
Jan  1 01:00:38 kernel: [   32.780000] PPP generic driver version 2.4.2
Jan  1 01:00:38 kernel: [   32.930000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan  1 01:00:38 kernel: [   33.360000] NET: Registered protocol family 24
Jan  1 01:00:38 kernel: [   33.420000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Jan  1 01:00:38 kernel: [   34.060000] xt_time: kernel timezone is -0000
Jan  1 01:00:38 kernel: [   34.780000]     Hooked IMQ after mangle on PREROUTING
Jan  1 01:00:38 kernel: [   34.780000]     Hooked IMQ after nat on POSTROUTING
Jan  1 01:00:38 kernel: [   34.780000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan  1 01:00:38 kernel: [   34.990000] Netfilter messages via NETLINK v0.30.
Jan  1 01:00:38 kernel: [   35.050000] ip_set: protocol 6
Jan  1 01:00:38 kernel: [   35.640000] usbcore: registered new interface driver cdc_acm
Jan  1 01:00:38 kernel: [   35.650000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan  1 01:00:38 kernel: [   35.790000] usbcore: registered new interface driver usbserial
Jan  1 01:00:38 kernel: [   35.790000] USB Serial support registered for generic
Jan  1 01:00:38 kernel: [   35.800000] usbcore: registered new interface driver usbserial_generic
Jan  1 01:00:38 kernel: [   35.800000] usbserial: USB Serial Driver core
Jan  1 01:00:38 kernel: [   35.850000] usbcore: registered new interface driver cdc_ether
Jan  1 01:00:38 kernel: [   36.000000] usbcore: registered new interface driver cdc_ncm
Jan  1 01:00:38 kernel: [   36.030000] USB Serial support registered for FTDI USB Serial Device
Jan  1 01:00:38 kernel: [   36.040000] ftdi_sio 1-1.3:1.0: FTDI USB Serial Device converter detected
Jan  1 01:00:38 kernel: [   36.040000] usb 1-1.3: Detected FT232RL
Jan  1 01:00:38 kernel: [   36.050000] usb 1-1.3: Number of endpoints 2
Jan  1 01:00:38 kernel: [   36.050000] usb 1-1.3: Endpoint 1 MaxPacketSize 16384
Jan  1 01:00:38 kernel: [   36.060000] usb 1-1.3: Endpoint 2 MaxPacketSize 16384
Jan  1 01:00:38 kernel: [   36.060000] usb 1-1.3: Setting MaxPacketSize 64
Jan  1 01:00:38 kernel: [   36.070000] usb 1-1.3: FTDI USB Serial Device converter now attached to ttyUSB0
Jan  1 01:00:38 kernel: [   36.070000] usbcore: registered new interface driver ftdi_sio
Jan  1 01:00:38 kernel: [   36.080000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
Jan  1 01:00:38 kernel: [   36.190000] USB Serial support registered for GSM modem (1-port)
Jan  1 01:00:38 kernel: [   36.200000] usbcore: registered new interface driver option
Jan  1 01:00:38 kernel: [   36.200000] option: v0.7.2:USB Driver for GSM modems
Jan  1 01:00:38 kernel: [   36.330000] USB Serial support registered for Sierra USB modem
Jan  1 01:00:38 kernel: [   36.330000] usbcore: registered new interface driver sierra
Jan  1 01:00:38 kernel: [   36.340000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
Jan  1 01:00:40 usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan  1 01:00:41 usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB_2.0_Hub Serial=?
Jan  1 01:00:41 usb-modeswitch: 1-1.3:1.0: Manufacturer=MERA-PROJEKT Product=USB_<->_1Wire_(MP00206) Serial=MPWZLJCH
Jan  1 01:00:42 usb-modeswitch: 1-1.4:1.0: Manufacturer=TOSHIBA Product=TransMemory Serial=CC52AF4C827ACD70E3C09135
Jan  1 01:00:44 netifd: Interface 'lan' is now up
Jan  1 01:00:44 kernel: [   44.870000] device eth0 entered promiscuous mode
Jan  1 01:00:44 netifd: Interface 'loopback' is now up
Jan  1 01:00:45 firewall: Reloading firewall due to ifup of lan (br-lan)
Jan  1 01:00:47 sysinit: command failed: Device or resource busy (-16)
Jan  1 01:00:49 kernel: [   49.560000] device wlan0 entered promiscuous mode
Jan  1 01:00:51 fstab: mount: mounting /dev/sda1 on /mnt/sda1 failed: Invalid argument
Jan  1 01:00:54 netifd: wan (1584): udhcpc (v1.19.4) started
Jan  1 01:00:54 netifd: wan (1584): Sending discover...
Jan  1 01:00:55 kernel: [   55.050000] device wlan0-1 entered promiscuous mode
May 28 16:00:01 kernel: [   55.370000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:00:01 kernel: [   55.380000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:00:01 kernel: [   55.380000] wlan0-1: authenticated
May 28 16:00:01 kernel: [   55.410000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:00:01 kernel: [   55.420000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:00:01 kernel: [   55.420000] wlan0-1: associated
May 28 16:00:01 kernel: [   55.430000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:00:01 kernel: [   55.430000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:00:02 kernel: [   57.080000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:00:02 kernel: [   57.080000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:00:03 netifd: wan (1584): Sending discover...
May 28 16:00:03 dropbear[1773]: Running in background
May 28 16:00:03 kernel: [   57.430000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:00:03 httpd_gargoyle[1802]: started as root without requesting chroot(), warning only
May 28 16:00:03 httpd_gargoyle[1802]: httpd_gargoyle/1.0 14mar2008 starting on Gargoyle, port 80
May 28 16:00:03 netifd: wan (1584): Sending select for 192.168.1.100...
May 28 16:00:04 netifd: wan (1584): Lease of 192.168.1.100 obtained, lease time 268435455
May 28 16:00:04 netifd: Interface 'wan' is now up
May 28 16:00:04 dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
May 28 16:00:04 dnsmasq: Allowing 127.0.0.0/8 responses
May 28 16:00:04 dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
May 28 16:00:04 kernel: [   59.080000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:00:08 dnsmasq[1888]: started, version 2.66 cachesize 150
May 28 16:00:08 dnsmasq[1888]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
May 28 16:00:08 dnsmasq-dhcp[1888]: DHCP, IP range 192.168.2.101 -- 192.168.2.254, lease time 12h
May 28 16:00:08 dnsmasq[1888]: using local addresses only for domain lan
May 28 16:00:08 dnsmasq[1888]: reading /tmp/resolv.conf.auto
May 28 16:00:08 dnsmasq[1888]: using nameserver 192.168.1.1#53
May 28 16:00:08 dnsmasq[1888]: ignoring nameserver 192.168.2.100 - local interface
May 28 16:00:08 dnsmasq[1888]: using local addresses only for domain lan
May 28 16:00:08 dnsmasq[1888]: read /etc/hosts - 2 addresses
May 28 16:00:08 dnsmasq-dhcp[1888]: read /etc/ethers - 0 addresses
May 28 16:00:08 sysinit: ERROR: No valid dynamic DNS service configurations defined
May 28 16:00:08 sysinit: (Did you specify correct configuration file path?)
May 28 16:00:09 sysinit: setting up led USB
May 28 16:00:09 sysinit: setting up led WLAN
May 28 16:00:09 sysinit: setting up led LAN
May 28 16:41:52 firewall: Reloading firewall due to ifup of wan (br-wan)
May 28 16:42:40 kernel: [  126.060000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:42:41 kernel: [  127.060000] br-lan: port 2(wlan0) entered disabled state
May 28 16:42:43 kernel: [  128.770000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:42:43 kernel: [  128.780000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:42:43 kernel: [  128.780000] wlan0-1: authenticated
May 28 16:42:43 kernel: [  128.830000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:42:43 kernel: [  128.940000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:42:43 kernel: [  128.940000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:42:43 kernel: [  128.950000] wlan0-1: associated
May 28 16:42:43 kernel: [  128.960000] ath: phy0: Failed to stop TX DMA, queues=0x001!
May 28 16:42:43 kernel: [  128.980000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:43 kernel: [  128.990000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:45 kernel: [  130.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:42:46 kernel: [  131.710000] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
May 28 16:42:46 kernel: [  131.720000]                old minutes west=0, new minutes west=-120
May 28 16:42:46 kernel: [  132.200000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:42:46 kernel: [  132.210000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:42:47 kernel: [  133.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:42:47 kernel: [  133.210000] wlan0-1: authenticated
May 28 16:42:47 kernel: [  133.240000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:42:48 kernel: [  134.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:42:49 kernel: [  135.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:42:49 kernel: [  135.230000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:42:49 kernel: [  135.240000] wlan0-1: associated
May 28 16:42:49 kernel: [  135.240000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:49 kernel: [  135.250000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:51 kernel: [  136.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:42:52 kernel: [  138.370000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:42:52 kernel: [  138.380000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:42:53 kernel: [  139.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:42:54 kernel: [  139.390000] wlan0-1: authenticated
May 28 16:42:54 kernel: [  139.420000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:42:54 kernel: [  140.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:42:55 kernel: [  141.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:42:56 kernel: [  141.410000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:42:56 kernel: [  141.420000] wlan0-1: associated
May 28 16:42:56 kernel: [  141.420000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:56 kernel: [  141.430000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:58 kernel: [  143.430000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:42:58 kernel: [  143.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:43:09 kernel: [  154.800000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:43:09 kernel: [  154.810000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:43:10 kernel: [  155.820000] wlan0-1: authenticated
May 28 16:43:10 kernel: [  155.850000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:43:11 kernel: [  157.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:43:12 kernel: [  157.840000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:43:12 kernel: [  157.850000] wlan0-1: associated
May 28 16:43:12 kernel: [  157.850000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:43:12 kernel: [  157.860000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:43:14 kernel: [  159.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:43:34 kernel: [  179.420000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:43:34 kernel: [  179.430000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:43:34 kernel: [  180.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:43:35 kernel: [  180.440000] wlan0-1: authenticated
May 28 16:43:35 kernel: [  180.470000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:43:35 kernel: [  181.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:43:36 kernel: [  182.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:43:37 kernel: [  182.460000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:43:37 kernel: [  182.470000] wlan0-1: associated
May 28 16:43:37 kernel: [  182.470000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:43:37 kernel: [  182.480000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:43:39 kernel: [  184.480000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:43:39 kernel: [  184.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:43:59 kernel: [  204.410000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:43:59 kernel: [  204.420000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:43:59 kernel: [  205.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:44:00 kernel: [  205.430000] wlan0-1: authenticated
May 28 16:44:00 kernel: [  205.460000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:44:00 kernel: [  206.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:44:01 kernel: [  207.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:44:02 kernel: [  207.450000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:44:02 kernel: [  207.460000] wlan0-1: associated
May 28 16:44:02 kernel: [  207.460000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:02 kernel: [  207.470000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:04 kernel: [  209.470000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:04 kernel: [  209.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:44:24 kernel: [  229.420000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:44:24 kernel: [  229.430000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:44:24 kernel: [  230.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:44:25 kernel: [  230.440000] wlan0-1: authenticated
May 28 16:44:25 kernel: [  230.470000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:44:25 kernel: [  231.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:44:26 kernel: [  232.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:44:27 kernel: [  232.460000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:44:27 kernel: [  232.470000] wlan0-1: associated
May 28 16:44:27 kernel: [  232.470000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:27 kernel: [  232.480000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:29 kernel: [  234.480000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:29 kernel: [  234.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:44:49 kernel: [  254.410000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:44:49 kernel: [  254.420000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:44:49 kernel: [  255.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:44:50 kernel: [  255.430000] wlan0-1: authenticated
May 28 16:44:50 kernel: [  255.460000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:44:50 kernel: [  256.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:44:51 kernel: [  257.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:44:52 kernel: [  257.450000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:44:52 kernel: [  257.460000] wlan0-1: associated
May 28 16:44:52 kernel: [  257.460000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:52 kernel: [  257.470000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:54 kernel: [  259.470000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:44:54 kernel: [  259.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:45:14 kernel: [  280.200000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:45:14 kernel: [  280.200000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:45:16 kernel: [  282.200000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:45:24 kernel: [  290.160000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:45:24 kernel: [  290.170000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:45:25 kernel: [  291.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:45:25 kernel: [  291.180000] wlan0-1: authenticated
May 28 16:45:25 kernel: [  291.200000] br-lan: port 2(wlan0) entered disabled state
May 28 16:45:25 kernel: [  291.220000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:45:26 kernel: [  292.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:45:27 kernel: [  293.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:45:27 kernel: [  293.210000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:45:27 kernel: [  293.220000] wlan0-1: associated
May 28 16:45:27 kernel: [  293.220000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:45:27 kernel: [  293.230000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:45:29 kernel: [  294.540000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:45:59 kernel: [  325.270000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:45:59 kernel: [  325.280000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:46:00 kernel: [  326.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:46:00 kernel: [  326.290000] wlan0-1: authenticated
May 28 16:46:00 kernel: [  326.320000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:46:01 kernel: [  327.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:46:02 kernel: [  328.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:46:02 kernel: [  328.310000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:46:02 kernel: [  328.320000] wlan0-1: associated
May 28 16:46:02 kernel: [  328.320000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:46:02 kernel: [  328.330000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:46:04 kernel: [  330.330000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:46:05 kernel: [  330.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:46:35 kernel: [  361.240000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:46:35 kernel: [  361.250000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:46:36 kernel: [  362.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:46:36 kernel: [  362.260000] wlan0-1: authenticated
May 28 16:46:36 kernel: [  362.290000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:46:37 kernel: [  363.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:46:38 kernel: [  364.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:46:38 kernel: [  364.280000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:46:38 kernel: [  364.290000] wlan0-1: associated
May 28 16:46:38 kernel: [  364.290000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:46:38 kernel: [  364.300000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:46:40 kernel: [  366.300000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:46:41 kernel: [  366.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:47:11 kernel: [  397.230000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:47:11 kernel: [  397.240000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:47:12 kernel: [  398.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:47:12 kernel: [  398.250000] wlan0-1: authenticated
May 28 16:47:12 kernel: [  398.280000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:47:13 kernel: [  399.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:47:14 kernel: [  400.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:47:14 kernel: [  400.270000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:47:14 kernel: [  400.280000] wlan0-1: associated
May 28 16:47:14 kernel: [  400.280000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:47:14 kernel: [  400.290000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:47:16 kernel: [  402.290000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:47:17 kernel: [  402.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:47:47 kernel: [  433.240000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:47:47 kernel: [  433.250000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:47:48 kernel: [  434.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:47:48 kernel: [  434.260000] wlan0-1: authenticated
May 28 16:47:48 kernel: [  434.290000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:47:49 kernel: [  435.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:47:50 kernel: [  436.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:47:50 kernel: [  436.280000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:47:50 kernel: [  436.290000] wlan0-1: associated
May 28 16:47:50 kernel: [  436.290000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:47:50 kernel: [  436.300000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:47:52 kernel: [  438.300000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:47:53 kernel: [  438.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:48:10 kernel: [  455.860000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:48:10 kernel: [  455.860000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:48:12 kernel: [  457.860000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:48:54 kernel: [  499.530000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:48:54 kernel: [  499.540000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:48:55 kernel: [  500.550000] wlan0-1: authenticated
May 28 16:48:55 kernel: [  500.570000] br-lan: port 2(wlan0) entered disabled state
May 28 16:48:55 kernel: [  500.590000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:48:56 kernel: [  502.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:48:57 kernel: [  502.580000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:48:57 kernel: [  502.590000] wlan0-1: associated
May 28 16:48:57 kernel: [  502.590000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:48:57 kernel: [  502.600000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:48:59 kernel: [  504.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:50:00 kernel: [  566.010000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:50:00 kernel: [  566.020000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:50:01 kernel: [  567.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:50:01 kernel: [  567.030000] wlan0-1: authenticated
May 28 16:50:01 kernel: [  567.060000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:50:02 kernel: [  568.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:50:03 kernel: [  569.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:50:03 kernel: [  569.050000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:50:03 kernel: [  569.060000] wlan0-1: associated
May 28 16:50:03 kernel: [  569.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:50:03 kernel: [  569.070000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:50:05 kernel: [  570.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:51:04 kernel: [  630.230000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:51:04 kernel: [  630.230000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:51:06 kernel: [  631.990000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:51:06 kernel: [  632.000000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:51:06 kernel: [  632.230000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:51:07 kernel: [  633.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:51:07 kernel: [  633.020000] wlan0-1: authenticated
May 28 16:51:07 kernel: [  633.030000] br-lan: port 2(wlan0) entered disabled state
May 28 16:51:07 kernel: [  633.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:51:08 kernel: [  634.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:51:09 kernel: [  635.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:51:09 kernel: [  635.040000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:51:09 kernel: [  635.050000] wlan0-1: associated
May 28 16:51:09 kernel: [  635.050000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:51:09 kernel: [  635.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:51:11 kernel: [  636.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:52:12 kernel: [  698.040000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:52:12 kernel: [  698.050000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:52:13 kernel: [  699.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:52:13 kernel: [  699.060000] wlan0-1: authenticated
May 28 16:52:13 kernel: [  699.090000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:52:14 kernel: [  700.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:52:15 kernel: [  701.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:52:15 kernel: [  701.080000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:52:15 kernel: [  701.090000] wlan0-1: associated
May 28 16:52:15 kernel: [  701.090000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:52:15 kernel: [  701.100000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:52:15 kernel: [  701.110000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:52:15 kernel: [  701.110000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:52:16 kernel: [  702.090000] br-lan: port 2(wlan0) entered disabled state
May 28 16:52:17 kernel: [  703.090000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:53:18 kernel: [  764.000000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:53:18 kernel: [  764.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:53:19 kernel: [  765.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:53:19 kernel: [  765.020000] wlan0-1: authenticated
May 28 16:53:19 kernel: [  765.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:53:20 kernel: [  766.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:53:21 kernel: [  767.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:53:21 kernel: [  767.040000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:53:21 kernel: [  767.050000] wlan0-1: associated
May 28 16:53:21 kernel: [  767.050000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:53:21 kernel: [  767.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:53:23 kernel: [  768.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:54:24 kernel: [  830.010000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:54:24 kernel: [  830.020000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:54:25 kernel: [  831.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:54:25 kernel: [  831.030000] wlan0-1: authenticated
May 28 16:54:25 kernel: [  831.060000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:54:26 kernel: [  832.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:54:27 kernel: [  833.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:54:27 kernel: [  833.050000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:54:27 kernel: [  833.060000] wlan0-1: associated
May 28 16:54:27 kernel: [  833.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:54:27 kernel: [  833.070000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:54:29 kernel: [  834.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:55:30 kernel: [  896.010000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:55:30 kernel: [  896.020000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:55:31 kernel: [  897.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:55:31 kernel: [  897.030000] wlan0-1: authenticated
May 28 16:55:31 kernel: [  897.060000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:55:32 kernel: [  898.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:55:33 kernel: [  899.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:55:33 kernel: [  899.050000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:55:33 kernel: [  899.060000] wlan0-1: associated
May 28 16:55:33 kernel: [  899.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:55:33 kernel: [  899.070000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:55:35 kernel: [  900.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:56:35 kernel: [  960.410000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:56:35 kernel: [  960.420000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:56:36 kernel: [  961.990000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:56:36 kernel: [  962.000000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:56:37 kernel: [  962.420000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:56:37 kernel: [  963.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:56:37 kernel: [  963.020000] wlan0-1: authenticated
May 28 16:56:37 kernel: [  963.030000] br-lan: port 2(wlan0) entered disabled state
May 28 16:56:37 kernel: [  963.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:56:38 kernel: [  964.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:56:39 kernel: [  965.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:56:39 kernel: [  965.040000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:56:39 kernel: [  965.050000] wlan0-1: associated
May 28 16:56:39 kernel: [  965.050000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:56:39 kernel: [  965.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:56:41 kernel: [  966.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:57:42 kernel: [ 1028.000000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:57:42 kernel: [ 1028.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:57:43 kernel: [ 1029.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:57:43 kernel: [ 1029.020000] wlan0-1: authenticated
May 28 16:57:43 kernel: [ 1029.050000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:57:44 kernel: [ 1030.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:57:45 kernel: [ 1031.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:57:45 kernel: [ 1031.040000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:57:45 kernel: [ 1031.050000] wlan0-1: associated
May 28 16:57:45 kernel: [ 1031.050000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:57:45 kernel: [ 1031.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:57:47 kernel: [ 1032.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:58:48 kernel: [ 1094.010000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 16:58:48 kernel: [ 1094.020000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 16:58:49 kernel: [ 1095.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 16:58:49 kernel: [ 1095.030000] wlan0-1: authenticated
May 28 16:58:49 kernel: [ 1095.060000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 16:58:50 kernel: [ 1096.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 16:58:51 kernel: [ 1097.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 16:58:51 kernel: [ 1097.050000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 16:58:51 kernel: [ 1097.060000] wlan0-1: associated
May 28 16:58:51 kernel: [ 1097.060000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:58:51 kernel: [ 1097.070000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 16:58:53 kernel: [ 1098.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 16:59:55 kernel: [ 1160.430000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:59:55 kernel: [ 1160.440000] br-lan: port 2(wlan0) entered forwarding state
May 28 16:59:57 kernel: [ 1162.440000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:00:53 kernel: [ 1219.070000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:00:53 kernel: [ 1219.080000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:00:54 kernel: [ 1220.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 17:00:54 kernel: [ 1220.090000] wlan0-1: authenticated
May 28 17:00:54 kernel: [ 1220.110000] br-lan: port 2(wlan0) entered disabled state
May 28 17:00:54 kernel: [ 1220.130000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:00:55 kernel: [ 1221.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:00:56 kernel: [ 1222.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 17:00:56 kernel: [ 1222.120000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 17:00:56 kernel: [ 1222.130000] wlan0-1: associated
May 28 17:00:56 kernel: [ 1222.130000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:00:56 kernel: [ 1222.140000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:00:58 kernel: [ 1223.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:02:05 kernel: [ 1290.420000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:02:05 kernel: [ 1290.420000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:02:07 kernel: [ 1292.420000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:02:58 kernel: [ 1344.140000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:02:58 kernel: [ 1344.150000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:02:59 kernel: [ 1345.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 17:02:59 kernel: [ 1345.160000] wlan0-1: authenticated
May 28 17:02:59 kernel: [ 1345.180000] br-lan: port 2(wlan0) entered disabled state
May 28 17:02:59 kernel: [ 1345.200000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:03:00 kernel: [ 1346.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:03:01 kernel: [ 1347.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 17:03:01 kernel: [ 1347.190000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 17:03:01 kernel: [ 1347.200000] wlan0-1: associated
May 28 17:03:01 kernel: [ 1347.200000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:03:01 kernel: [ 1347.210000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:03:03 kernel: [ 1348.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:04:35 kernel: [ 1440.430000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:04:35 kernel: [ 1440.430000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:04:37 kernel: [ 1442.430000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:05:04 kernel: [ 1469.420000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:05:04 kernel: [ 1469.430000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:05:04 kernel: [ 1470.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 17:05:05 kernel: [ 1470.440000] wlan0-1: authenticated
May 28 17:05:05 kernel: [ 1470.460000] br-lan: port 2(wlan0) entered disabled state
May 28 17:05:05 kernel: [ 1470.480000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:05:05 kernel: [ 1471.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:05:06 kernel: [ 1472.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 17:05:07 kernel: [ 1472.470000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 17:05:07 kernel: [ 1472.480000] wlan0-1: associated
May 28 17:05:07 kernel: [ 1472.480000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:05:07 kernel: [ 1472.490000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:05:09 kernel: [ 1474.490000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:05:09 kernel: [ 1474.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:06:05 kernel: [ 1530.440000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:06:05 kernel: [ 1530.440000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:06:07 kernel: [ 1532.440000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:07:09 kernel: [ 1595.020000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:07:09 kernel: [ 1595.030000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:07:10 kernel: [ 1596.010000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 2/3)
May 28 17:07:10 kernel: [ 1596.040000] wlan0-1: authenticated
May 28 17:07:10 kernel: [ 1596.060000] br-lan: port 2(wlan0) entered disabled state
May 28 17:07:10 kernel: [ 1596.080000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:07:11 kernel: [ 1597.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:07:12 kernel: [ 1598.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 3/3)
May 28 17:07:12 kernel: [ 1598.070000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 17:07:12 kernel: [ 1598.080000] wlan0-1: associated
May 28 17:07:12 kernel: [ 1598.080000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:07:12 kernel: [ 1598.090000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:07:14 kernel: [ 1599.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:08:55 kernel: [ 1700.450000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:08:55 kernel: [ 1700.450000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:08:57 kernel: [ 1702.450000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:09:15 kernel: [ 1720.530000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:09:15 kernel: [ 1720.540000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:09:16 kernel: [ 1721.550000] wlan0-1: authenticated
May 28 17:09:16 kernel: [ 1721.570000] br-lan: port 2(wlan0) entered disabled state
May 28 17:09:16 kernel: [ 1721.590000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:09:17 kernel: [ 1723.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:09:18 kernel: [ 1723.580000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=1)
May 28 17:09:18 kernel: [ 1723.590000] wlan0-1: associated
May 28 17:09:18 kernel: [ 1723.590000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:09:18 kernel: [ 1723.600000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:09:20 kernel: [ 1725.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:11:21 kernel: [ 1846.780000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:11:21 kernel: [ 1846.790000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:11:22 kernel: [ 1847.800000] wlan0-1: authenticated
May 28 17:11:22 kernel: [ 1847.830000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:11:23 kernel: [ 1849.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:11:24 kernel: [ 1849.820000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=1)
May 28 17:11:24 kernel: [ 1849.830000] wlan0-1: associated
May 28 17:11:24 kernel: [ 1849.830000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:11:24 kernel: [ 1849.840000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:11:26 kernel: [ 1851.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:12:31 kernel: [ 1916.810000] eth0: link up (100Mbps/Full duplex)
May 28 17:12:31 kernel: [ 1916.810000] br-lan: port 1(eth0) entered forwarding state
May 28 17:12:31 kernel: [ 1916.820000] br-lan: port 1(eth0) entered forwarding state
May 28 17:12:33 kernel: [ 1918.820000] br-lan: port 1(eth0) entered forwarding state
May 28 17:12:34 dnsmasq-dhcp[1888]: DHCPREQUEST(br-lan) 192.168.2.139 00:1a:4b:59:22:2e 
May 28 17:12:34 dnsmasq-dhcp[1888]: DHCPACK(br-lan) 192.168.2.139 00:1a:4b:59:22:2e laptop_hp
May 28 17:12:54 dropbear[6544]: Child connection from 192.168.2.139:1425
May 28 17:13:04 dropbear[6544]: Password auth succeeded for 'root' from 192.168.2.139:1425
May 28 17:13:27 kernel: [ 1972.840000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:13:27 kernel: [ 1972.850000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:13:28 kernel: [ 1973.860000] wlan0-1: authenticated
May 28 17:13:28 kernel: [ 1973.890000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:13:29 kernel: [ 1975.010000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 2/3)
May 28 17:13:30 kernel: [ 1975.880000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=3)
May 28 17:13:30 kernel: [ 1975.890000] wlan0-1: associated
May 28 17:13:30 kernel: [ 1975.890000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:13:30 kernel: [ 1975.900000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:13:32 kernel: [ 1977.500000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:13:47 kernel: [ 1993.340000] device wlan0 left promiscuous mode
May 28 17:13:47 kernel: [ 1993.340000] br-lan: port 2(wlan0) entered disabled state
May 28 17:13:48 kernel: [ 1993.800000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:13:48 kernel: [ 1993.810000] device wlan0-1 left promiscuous mode
May 28 17:13:48 kernel: [ 1993.820000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:13:50 netifd: wan (1584): Received SIGTERM
May 28 17:13:50 netifd: Interface 'wan' is now down
May 28 17:13:51 kernel: [ 1996.700000] device wlan0 entered promiscuous mode
May 28 17:13:55 netifd: wan (6985): udhcpc (v1.19.4) started
May 28 17:13:55 netifd: wan (6985): Sending discover...
May 28 17:13:56 kernel: [ 2001.660000] device wlan0-1 entered promiscuous mode
May 28 17:13:56 kernel: [ 2001.930000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:13:56 kernel: [ 2001.940000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:13:56 kernel: [ 2001.950000] wlan0-1: authenticated
May 28 17:13:56 kernel: [ 2001.960000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:13:56 kernel: [ 2001.960000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=2)
May 28 17:13:56 kernel: [ 2001.970000] wlan0-1: associated
May 28 17:13:56 kernel: [ 2001.970000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:13:56 kernel: [ 2001.980000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:13:57 kernel: [ 2003.290000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:13:57 kernel: [ 2003.290000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:13:58 netifd: wan (6985): Sending discover...
May 28 17:13:58 kernel: [ 2003.980000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:13:59 netifd: wan (6985): Sending select for 192.168.1.100...
May 28 17:13:59 netifd: wan (6985): Lease of 192.168.1.100 obtained, lease time 268435455
May 28 17:13:59 dnsmasq[1888]: reading /tmp/resolv.conf.auto
May 28 17:13:59 dnsmasq[1888]: ignoring nameserver 192.168.2.100 - local interface
May 28 17:13:59 dnsmasq[1888]: using local addresses only for domain lan
May 28 17:13:59 netifd: Interface 'wan' is now up
May 28 17:13:59 kernel: [ 2005.290000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:14:00 firewall: Reloading firewall due to ifup of wan (br-wan)
May 28 17:14:04 dnsmasq[1888]: reading /tmp/resolv.conf.auto
May 28 17:14:04 dnsmasq[1888]: using nameserver 192.168.1.1#53
May 28 17:14:04 dnsmasq[1888]: ignoring nameserver 192.168.2.100 - local interface
May 28 17:14:04 dnsmasq[1888]: using local addresses only for domain lan
May 28 17:17:12 dropbear[8038]: Child connection from 192.168.2.139:1520
May 28 17:17:17 kernel: [ 2202.650000] device wlan0 left promiscuous mode
May 28 17:17:17 kernel: [ 2202.660000] br-lan: port 2(wlan0) entered disabled state
May 28 17:17:17 kernel: [ 2202.720000] wlan0-1: deauthenticating from e8:94:f6:9a:90:2c by local choice (reason=3)
May 28 17:17:17 kernel: [ 2202.750000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:17:17 kernel: [ 2203.180000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:17:17 kernel: [ 2203.200000] device wlan0-1 left promiscuous mode
May 28 17:17:17 kernel: [ 2203.200000] br-wan: port 1(wlan0-1) entered disabled state
May 28 17:17:18 netifd: wan (6985): Received SIGTERM
May 28 17:17:18 netifd: Interface 'wan' is now down
May 28 17:17:19 kernel: [ 2205.130000] device wlan0 entered promiscuous mode
May 28 17:17:23 netifd: wan (8332): udhcpc (v1.19.4) started
May 28 17:17:23 netifd: wan (8332): Sending discover...
May 28 17:17:24 kernel: [ 2210.130000] device wlan0-1 entered promiscuous mode
May 28 17:17:25 kernel: [ 2210.400000] wlan0-1: authenticate with e8:94:f6:9a:90:2c
May 28 17:17:25 kernel: [ 2210.410000] wlan0-1: send auth to e8:94:f6:9a:90:2c (try 1/3)
May 28 17:17:25 kernel: [ 2210.420000] wlan0-1: authenticated
May 28 17:17:25 kernel: [ 2210.430000] wlan0-1: associate with e8:94:f6:9a:90:2c (try 1/3)
May 28 17:17:25 kernel: [ 2210.430000] wlan0-1: RX AssocResp from e8:94:f6:9a:90:2c (capab=0x431 status=0 aid=2)
May 28 17:17:25 kernel: [ 2210.440000] wlan0-1: associated
May 28 17:17:25 kernel: [ 2210.440000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:17:25 kernel: [ 2210.450000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:17:26 kernel: [ 2211.760000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:17:26 kernel: [ 2211.760000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:17:26 netifd: wan (8332): Sending discover...
May 28 17:17:27 kernel: [ 2212.450000] br-wan: port 1(wlan0-1) entered forwarding state
May 28 17:17:27 netifd: wan (8332): Sending select for 192.168.1.100...
May 28 17:17:28 netifd: wan (8332): Lease of 192.168.1.100 obtained, lease time 268435455
May 28 17:17:28 dnsmasq[1888]: reading /tmp/resolv.conf.auto
May 28 17:17:28 dnsmasq[1888]: ignoring nameserver 192.168.2.100 - local interface
May 28 17:17:28 dnsmasq[1888]: using local addresses only for domain lan
May 28 17:17:28 netifd: Interface 'wan' is now up
May 28 17:17:28 kernel: [ 2213.760000] br-lan: port 2(wlan0) entered forwarding state
May 28 17:17:28 firewall: Reloading firewall due to ifup of wan (br-wan)
May 28 17:17:32 dnsmasq[1888]: reading /tmp/resolv.conf.auto
May 28 17:17:32 dnsmasq[1888]: using nameserver 192.168.1.1#53
May 28 17:17:32 dnsmasq[1888]: ignoring nameserver 192.168.2.100 - local interface
May 28 17:17:32 dnsmasq[1888]: using local addresses only for domain lan
May 28 17:17:50 dropbear[8038]: Password auth succeeded for 'root' from 192.168.2.139:1520

FAQ o OpenWrt | Sprzedam różne routery | Oddam

MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Posty: 7

1 Temat przez r_afaello 2014-05-27 08:32:17

Temat: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

2 Odpowiedź przez Cezary 2014-05-27 08:43:57

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

3 Odpowiedź przez r_afaello 2014-05-27 09:05:13 (edytowany przez r_afaello 2014-05-27 09:05:59)

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

4 Odpowiedź przez Cezary 2014-05-27 09:06:11

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

5 Odpowiedź przez r_afaello 2014-05-28 17:06:14

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

6 Odpowiedź przez Cezary 2014-05-28 17:12:33

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

7 Odpowiedź przez r_afaello 2014-05-28 17:33:21

Odp: MR3020 - mało miejsca a chcę mieć FSCK - da się ?

Posty: 7