#!/bin/sh

#This script allows access to the ADSL modem web interface when pppoe is used.
#For this to work configure your modem in bridge mode with DHCP enabled on the m
#This will cause the modem to dish an address to the router interface when reque
#
#Alternatively you can manually set the below variable ROUTER_IP with the IP add
#you want to use.  Make sure the IP address is on the same network as the modem.
#ROUTER_IP=10.0.0.2

#Main case statement used only by udhcp which only calls with one of the
#following four key words in parameter 1.
case "$1" in
        deconfig)
                ifconfig "$interface" 0.0.0.0
        exit 0
        ;;
        renew)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadca
        exit 0
        ;;
        bound)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadca
- /etc/ppp/ip-up.d/modemaccess.sh 1/49 2%
#!/bin/sh

#This script allows access to the ADSL modem web interface when pppoe is used.
#For this to work configure your modem in bridge mode with DHCP enabled on the modem.
#This will cause the modem to dish an address to the router interface when requested below.
#
#Alternatively you can manually set the below variable ROUTER_IP with the IP address
#you want to use.  Make sure the IP address is on the same network as the modem.
#ROUTER_IP=10.0.0.2

#Main case statement used only by udhcp which only calls with one of the
#following four key words in parameter 1.
case "$1" in
        deconfig)
                ifconfig "$interface" 0.0.0.0
        exit 0
        ;;
        renew)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadcast ${broadcast:-+}
        exit 0
        ;;
        bound)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadcast ${broadcast:-+}
        exit 0
        ;;
        nak)
        exit 0
        ;;
        leasefail)
        exit 0
        ;;
esac

#if we get here then udhcp did not call us.  Must be from pppd or /usr/lib/gargoyle_firewall_util

#configure the ethernet interface.
if [ -n "$ROUTER_IP" ] ; then
        #In manual mode the user gave us an IP address for our interface
- /etc/ppp/ip-up.d/modemaccess.sh 1/49 2%
#!/bin/sh

#This script allows access to the ADSL modem web interface when pppoe is used.
#For this to work configure your modem in bridge mode with DHCP enabled on the modem.
#This will cause the modem to dish an address to the router interface when requested below.
#
#Alternatively you can manually set the below variable ROUTER_IP with the IP address
#you want to use.  Make sure the IP address is on the same network as the modem.
#ROUTER_IP=10.0.0.2

#Main case statement used only by udhcp which only calls with one of the
#following four key words in parameter 1.
case "$1" in
        deconfig)
                ifconfig "$interface" 0.0.0.0
        exit 0
        ;;
        renew)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadcast ${broadcast:-+}
        exit 0
        ;;
        bound)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadcast ${broadcast:-+}
        exit 0
        ;;
        nak)
        exit 0
        ;;
        leasefail)
        exit 0
        ;;
esac

#if we get here then udhcp did not call us.  Must be from pppd or /usr/lib/gargoyle_firewall_util

#configure the ethernet interface.
if [ -n "$ROUTER_IP" ] ; then
        #In manual mode the user gave us an IP address for our interface
        ifconfig $2 $ROUTER_IP netmask 255.255.255.0
else
        #In auto mode we first check if we have an ip address already.
        ROUTER_IP=$(ifconfig $2 | grep "inet addr:")
        if [ -z "$ROUTER_IP" ]; then
                #Dont have one so try an get one.
                udhcpc -f -i $2 -n -q -s /etc/ppp/ip-up.d/modemaccess.sh
        fi
fi

exit 0
~
~
~
~
~
- /etc/ppp/ip-up.d/modemaccess.sh 1/49 2%

#!/bin/sh

#This script allows access to the ADSL modem web interface when pppoe is used.
#For this to work configure your modem in bridge mode with DHCP enabled on the m
#This will cause the modem to dish an address to the router interface when reque
#
#Alternatively you can manually set the below variable ROUTER_IP with the IP add
#you want to use.  Make sure the IP address is on the same network as the modem.
ROUTER_IP=10.0.0.2

#Main case statement used only by udhcp which only calls with one of the
#following four key words in parameter 1.
case "$1" in
        deconfig)
                ifconfig "$interface" 0.0.0.0
        exit 0
        ;;
        renew)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadca
        exit 0
        ;;
        bound)
                ifconfig $interface $ip netmask ${subnet:-255.255.255.0} broadca
- /etc/ppp/ip-up.d/modemaccess.sh 1/49 2%
#!/bin/sh

root@Gargoyle:~# ifconfig
br-lan    Link encap:Ethernet  HWaddr XX:XX:XX:XX:XX:XX
          inet addr:192.168.3.1  Bcast:192.168.3.255  Mask:255.255.255.0
          inet6 addr: fe80::b248:7aff:fedb:5628/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:76534 errors:0 dropped:0 overruns:0 frame:0
          TX packets:116109 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:6775486 (6.4 MiB)  TX bytes:149898084 (142.9 MiB)

eth0      Link encap:Ethernet  HWaddr XX:XX:XX:XX:XX:XX
          inet6 addr: fe80::b248:7aff:fedb:5628/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:135180 errors:0 dropped:0 overruns:58644 frame:0
          TX packets:95787 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:154461334 (147.3 MiB)  TX bytes:37658399 (35.9 MiB)
          Interrupt:4

eth0.1    Link encap:Ethernet  HWaddr XX:XX:XX:XX:XX:XX
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:18379 errors:0 dropped:5 overruns:0 frame:0
          TX packets:25904 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2391497 (2.2 MiB)  TX bytes:29722034 (28.3 MiB)

eth0.2    Link encap:Ethernet  HWaddr XX:XX:XX:XX:XX:XX
          inet6 addr: fe80::b248:7aff:fedb:5628/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:116777 errors:0 dropped:0 overruns:0 frame:0
          TX packets:69758 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:149632621 (142.7 MiB)  TX bytes:7543148 (7.1 MiB)

imq0      Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 -00
          UP RUNNING NOARP  MTU:1500  Metric:1
          RX packets:116068 errors:0 dropped:0 overruns:0 frame:0
          TX packets:115830 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:11000
          RX bytes:148642846 (141.7 MiB)  TX bytes:148306599 (141.4 MiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:2298 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2298 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:159076 (155.3 KiB)  TX bytes:159076 (155.3 KiB)

pppoe-wan Link encap:Point-to-Point Protocol
          inet addr:83.26.217.25  P-t-P:213.25.2.132  Mask:255.255.255.255
          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
          RX packets:116131 errors:0 dropped:0 overruns:0 frame:0
          TX packets:69168 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:3
          RX bytes:148657497 (141.7 MiB)  TX bytes:6002634 (5.7 MiB)

wlan0     Link encap:Ethernet  HWaddr XX:XX:XX:XX:XX:XX
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:58623 errors:0 dropped:0 overruns:0 frame:0
          TX packets:93564 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:5329130 (5.0 MiB)  TX bytes:122484285 (116.8 MiB)