Temat: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

Witam mam problem z routerem mr-3420 v2.2 padł po zmianie fw z openwrt na gargoyle pl  opisany sposób odratowania Cezarego nie chce się u mnie wykonać złącze kabla dku podpięte pod płyte głowną na sztywno ustawiona karta sieciowa na 192.168.1.5  tftpd w zakładce server interfaces wykrywa karte na tym adresie ip w katalogu tftpd  wsad code.bin ale wciaz mam problem nizej log i prośba na nakierownie co zle robie

# Booting image at 9f020000 ...
   Uncompressing Kernel Image ... S�H�ص��ر1.1.4 (Mar 14 2013 - 11:09:54)dLZMA ERROR 1 - must RESET board to recover
U-boot AP123


DRAM:  32 MB
id read 0x100000ff
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
wasp reset mask:c03300
WASP ----> S27 PHY
file: ag934x.c,line: 179==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7114
eth0: ba:be:fa:ce:08:41
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth0 up
WASP ----> S27 PHY
file: ag934x.c,line: 179==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7214
eth1: ba:be:fa:ce:08:41
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x10
eth1 up
eth0, eth1
Autobooting in 1 seconds
wasp>
wasp> erase 0x9f020000 +0x3c0000

First 0x2 last 0x3d sector size 0x10000                                       61
Erased 60 sectors
wasp> tftpboot 0x81000000 code.bin
eth1 link down
enet0 port4 up
dup 1 speed 100
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.111
Filename 'code.bin'.
Load address: 0x81000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
eth1 link down

TFTP from server 192.168.1.100; our IP address is 192.168.1.111
Filename 'code.bin'.
Load address: 0x81000000
Loading: T T T T T

2

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

192.168.1.100 masz mieć ustawione na karcie sieciowej, napisał to.

Jak już odzyskasz go wgraj ponownie gargoyle pl i pokaż logi z uruchomienia.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

Prześledź ten temat: http://openrouter.info/forum/viewtopic. … amp;t=2707 i zamieść bootloga po wgraniu Gargoyle PL żeby było wiadomo gdzie się wykłada.

4

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

I przy okazji ponownego wgrywania weź nowy obraz który właśnie wygenerowałem.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

5 (edytowany przez tomasnew 2013-07-29 22:28:29)

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

poszedł ale panowie cos dziwnego komunikacja z serwerem tftp odbywa sie tylko po 2,3,4 porcie na 1 brak mozliwosci przesłania fw do ramu tak samo na porcie wan

log po wgraniu


U-Boot 1.1.4 (Mar 14 2013 - 11:09:54)

U-boot AP123


DRAM:  32 MB
id read 0x100000ff
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
wasp reset mask:c03300
WASP ----> S27 PHY
file: ag934x.c,line: 179==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0x5 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth0 up
WASP ----> S27 PHY
file: ag934x.c,line: 179==: set LAN&WAN SWAP. --debug by HouXB
GMAC: cfg1 0xf cfg2 0x7214
eth1: ba:be:fa:ce:08:41
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x10
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #11 Mon Jul 29 22:10:20 CEST 2013
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29044k/32768k available (2224k kernel code, 3724k reserved, 391k data, 184k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-MR3420 v2
[    0.510000] bio: create slab <bio-0> at 0
[    0.520000] Switching to clocksource MIPS
[    0.530000] NET: Registered protocol family 2
[    0.530000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.530000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.540000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.550000] TCP reno registered
[    0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.560000] NET: Registered protocol family 1
[    0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.590000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.600000] msgmni has been set to 56
[    0.600000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.610000] io scheduler noop registered
[    0.620000] io scheduler deadline registered (default)
[    0.620000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.660000] console [ttyS0] enabled, bootconsole disabled
[    0.660000] console [ttyS0] enabled, bootconsole disabled
[    0.670000] m25p80 spi0.0: found en25q32b, expected m25p80
[    0.680000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[    0.680000] 5 tp-link partitions found on MTD device spi0.0
[    0.690000] Creating 5 MTD partitions on "spi0.0":
[    0.700000] 0x000000000000-0x000000020000 : "u-boot"
[    0.700000] 0x000000020000-0x0000001096b4 : "kernel"
[    0.710000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.720000] 0x0000001096b4-0x0000003f0000 : "rootfs"
[    0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.740000] mtd: partition "rootfs" set to be root filesystem
[    0.750000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=60000
[    0.760000] 0x000000390000-0x0000003f0000 : "rootfs_data"
[    0.760000] 0x0000003f0000-0x000000400000 : "art"
[    0.770000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.360000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[    1.370000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    1.920000] eth1: Found an AR934X built-in switch
[    2.960000] TCP cubic registered
[    2.960000] NET: Registered protocol family 17
[    2.960000] Bridge firewalling registered
[    2.970000] Ebtables v2.0 registered
[    2.970000] 8021q: 802.1Q VLAN Support v1.8
[    2.980000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.990000] Freeing unused kernel memory: 184k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    8.290000] JFFS2 notice: (444) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 16 of xref (0 dead, 2 orphan) found.
[    8.890000] SCSI subsystem initialized
[    9.040000] usbcore: registered new interface driver usbfs
[    9.040000] usbcore: registered new interface driver hub
[    9.050000] usbcore: registered new device driver usb
[    9.440000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.450000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.450000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.490000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.510000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.510000] hub 1-0:1.0: USB hub found
[    9.520000] hub 1-0:1.0: 1 port detected
[    9.530000] Initializing USB Mass Storage driver...
[    9.540000] usbcore: registered new interface driver usb-storage
[    9.550000] USB Mass Storage support registered.

6

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

tomasnew napisał/a:

poszedł ale panowie cos dziwnego komunikacja z serwerem tftp odbywa sie tylko po 2,3,4 porcie na 1 brak mozliwosci przesłania fw do ramu tak samo na porcie wan

TP-Link ostatnio grzebie w U-Boot... może coś zepsuli przy okazji którejś aktualizacji.

7

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

Nie, raczej to że 3420v2 ma inne przypisane portów w switchu.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

8

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

Cezary napisał/a:

Nie, raczej to że 3420v2 ma inne przypisane portów w switchu.

Kilka tygodni temu stawiałem 3420v2 na nogi i wrzucałem obraz przez tftp w U-Boot przez port WAN, bo tylko na tym porcie było to możliwe.

9

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

witam
no niestety tez wgrałem gargoyle, do mr 3420 v 2.2, i też padło
czy aktualny firmware na stronie już ma wszystko tak jak trzeba i będzie to chodzić z ver 2,2?

10

Odp: mr-3420 v2.2 padł po zmianie z openwrt na gargoyle

Jak wyżej, tak działa.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.