FAQ o OpenWrt | Sprzedam różne routery | Oddam

Polarus · 2012-11-14 08:58:32

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Temat: Attitude Adjustment - extroot nie działa tak jak powinien

Witam,
Po stworzeniu oraz konfiguracji extroota w routerze TP-Link TL-MR3420 jakby go nie ma. Tu podaje wynik mount, df -h i treść pliku fstab.
root@Magistrala:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
/dev/sda2 on /overlay type ext4 (rw,noatime,user_xattr,barrier=1,data=ordered)
root@Magistrala:~# df -h
Filesystem Size Used Available Use% Mounted on
rootfs 384.0K 356.0K 28.0K 93% /
/dev/root 2.8M 2.8M 0 100% /rom
tmpfs 14.3M 2.4M 11.9M 17% /tmp
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock3 7.3G 237.8M 7.0G 3% /overlay
overlayfs:/overlay 384.0K 356.0K 28.0K 93% /
/dev/sda2 7.3G 237.8M 7.0G 3% /overlay
Niniejszym wygląda na to, jakby overlay miał 384 kb?

root@Magistrala:~# uci show fstab
fstab.automount=global
fstab.automount.from_fstab=1
fstab.automount.anon_mount=1
fstab.autoswap=global
fstab.autoswap.from_fstab=1
fstab.autoswap.anon_swap=0
fstab.@mount[0]=mount
fstab.@mount[0].target=/overlay
fstab.@mount[0].options=rw,noatime
fstab.@mount[0].enabled_fsck=0
fstab.@mount[0].enabled=1
fstab.@mount[0].device=/dev/sda2
fstab.@mount[0].uuid=8801348a-2b38-431e-ac1a-54674d329e08
fstab.@mount[0].fstype=ext4
fstab.@swap[0]=swap
fstab.@swap[0].device=/dev/sda99
fstab.@swap[0].enabled=0
root@Magistrala:~# ls /etc/rc.d/*
/etc/rc.d/K50dropbear /etc/rc.d/S11ubus /etc/rc.d/S39usb /etc/rc.d/S50dropbear /etc/rc.d/S60wol /etc/rc.d/S99sysctl
/etc/rc.d/K90network /etc/rc.d/S20fstab /etc/rc.d/S41sysntpd /etc/rc.d/S50telnet /etc/rc.d/S90ddns_gargoyle
/etc/rc.d/K98boot /etc/rc.d/S20network /etc/rc.d/S45firewall /etc/rc.d/S51httpd_gargoyle /etc/rc.d/S95done
/etc/rc.d/K99umount /etc/rc.d/S25time_backup /etc/rc.d/S49gargoyle_themes /etc/rc.d/S55bwmon_gargoyle /etc/rc.d/S96led
/etc/rc.d/S10boot /etc/rc.d/S30set_kernel_timezone /etc/rc.d/S50cron /etc/rc.d/S60dnsmasq /etc/rc.d/S97watchdog

Wygląda to wszystko na jakiś błąd - system plików nie jest uszkodzony, formatowany przed extroodem. Skopiowałem na niego zawartość /overlay, by zachować konfiguracje.

zdzichu6969 · 2012-11-14 09:10:45

zdzichu6969
Użytkownik
Nieaktywny

Skąd: Gniezno/Poznań
Zarejestrowany: 2012-07-30
Posty: 1,335

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

jest
/dev/sda2 7.3G 237.8M 7.0G 3% /overlay

RB760iGS + RB260GS / Ryzen 5 2660 / 16G DDR4 / MiniITX - Inea 1G (https://i.imgur.com/TLbJVDw.png)
RB951-2HnD / Celeron J1900 / 4G DDR3 / MiniITX - Satpol 100M

Polarus · 2012-11-14 09:14:16

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Też mi się tak zdawało, jednak przy próbie instalacji czegokolwiek pokazuje mi "no space left on device", analogicznie wolne miejsce na /overlayfs się zmniejsza. Zacytuje:
overlayfs:/overlay 384.0K 356.0K 28.0K 93% /

Cezary · 2012-11-14 09:26:01

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Nie ma: /dev/mtdblock3 7.3G 237.8M 7.0G 3% /overlay

Pokaż jaszcze wynik blkid.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 09:28:13

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Tu jest

root@Magistrala:~# blkid
/dev/mtdblock2: TYPE="squashfs"
/dev/sda1: UUID="20aed0bf-5368-4841-85b6-bc283d7c9d18" TYPE="swap"
/dev/sda2: UUID="8801348a-2b38-431e-ac1a-54674d329e08" TYPE="ext4"

Cezary · 2012-11-14 09:39:46

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Pokaż mi wynik logread jeszcze, po reboocie routera z tym pendrive. A tak w ogóle to co to jest za nośnik?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 10:03:40

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Czytnik MicroSD z kartą. Ale na backfire nigdy nie miałem z nim żadnego problemu z tym, że z wiadomych względów wcześniej był zawsze formatowany jako EXT2.

root@Magistrala:~# logread
Nov 14 00:00:20 Magistrala daemon.info dnsmasq-dhcp[1943]: read /etc/ethers - 1 addresses
Nov 14 00:00:20 Magistrala user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Nov 14 00:00:20 Magistrala user.info sysinit: (Did you specify correct configuration file path?)
Nov 14 00:00:21 Magistrala user.info sysinit: setting up led USB
Nov 14 00:00:21 Magistrala user.notice fstab: mount: mounting /dev/sda1 on /mnt/sda1 failed: Invalid argument
Nov 14 00:00:21 Magistrala kern.warn kernel: [ 69.060000] head: sending ioctl 540d to a partition!
Nov 14 00:00:21 Magistrala kern.warn kernel: [ 69.060000] head: sending ioctl 540d to a partition!
Nov 14 09:57:16 Magistrala user.notice ifup: Enabling Router Solicitations on wan (3g-wan)
Nov 14 09:57:17 Magistrala user.info firewall: adding wan (3g-wan) to zone wan
Nov 14 09:57:22 Magistrala kern.warn kernel: [ 84.580000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
Nov 14 09:57:22 Magistrala kern.warn kernel: [ 84.580000] old minutes west=0, new minutes west=-60
Nov 14 09:57:30 Magistrala kern.info kernel: [ 92.860000] IMQ driver unloaded successfully.
Nov 14 09:57:31 Magistrala kern.info kernel: [ 92.900000] Hooked IMQ after mangle on INPUT
Nov 14 09:57:31 Magistrala kern.info kernel: [ 92.900000] Hooked IMQ after mangle on FORWARD
Nov 14 09:57:31 Magistrala kern.info kernel: [ 92.910000] IMQ driver loaded successfully. (numdevs = 1, numqueues = 1)
Nov 14 09:57:37 Magistrala user.notice ifup: Enabling Router Solicitations on loopback (lo)
Nov 14 09:59:52 Magistrala daemon.info pppd[1227]: No response to 5 echo-requests
Nov 14 09:59:52 Magistrala daemon.notice pppd[1227]: Serial link appears to be disconnected.
Nov 14 09:59:52 Magistrala daemon.info pppd[1227]: Connect time 3.0 minutes.
Nov 14 09:59:52 Magistrala daemon.info pppd[1227]: Sent 40337 bytes, received 69419 bytes.
Nov 14 09:59:52 Magistrala daemon.notice netifd: Interface 'wan' has lost the connection
Nov 14 09:59:53 Magistrala daemon.notice pppd[1227]: Connection terminated.
Nov 14 10:00:01 Magistrala user.notice 3gtester: Restart wan connection
Nov 14 10:00:01 Magistrala daemon.info pppd[1227]: Terminating on signal 15
Nov 14 10:00:01 Magistrala daemon.info pppd[1227]: Exit.
Nov 14 10:00:01 Magistrala daemon.notice netifd: Interface 'wan' is now down
Nov 14 10:00:04 Magistrala daemon.notice netifd: wan (3062): SIM ready
Nov 14 10:00:04 Magistrala daemon.notice netifd: wan (3062): PIN set successfully
Nov 14 10:00:06 Magistrala daemon.notice pppd[3078]: pppd 2.4.5 started by root, uid 0
Nov 14 10:00:07 Magistrala local2.info chat[3082]: abort on (BUSY)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: abort on (NO CARRIER)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: abort on (ERROR)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: report (CONNECT)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: timeout set to 10 seconds
Nov 14 10:00:07 Magistrala local2.info chat[3082]: send (AT&F^M)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: expect (OK)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: AT&F^M^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: OK
Nov 14 10:00:07 Magistrala local2.info chat[3082]: -- got it
Nov 14 10:00:07 Magistrala local2.info chat[3082]: send (ATE1^M)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: expect (OK)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: ^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: ATE1^M^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: OK
Nov 14 10:00:07 Magistrala local2.info chat[3082]: -- got it
Nov 14 10:00:07 Magistrala local2.info chat[3082]: send (AT+CGDCONT=1,"IP","internet"^M)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: timeout set to 30 seconds
Nov 14 10:00:07 Magistrala local2.info chat[3082]: expect (OK)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: ^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: AT+CGDCONT=1,"IP","internet"^M^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: OK
Nov 14 10:00:07 Magistrala local2.info chat[3082]: -- got it
Nov 14 10:00:07 Magistrala local2.info chat[3082]: send (ATD*99***1#^M)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: expect (CONNECT)
Nov 14 10:00:07 Magistrala local2.info chat[3082]: ^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: ATD*99***1#^M^M
Nov 14 10:00:07 Magistrala local2.info chat[3082]: CONNECT
Nov 14 10:00:07 Magistrala local2.info chat[3082]: -- got it
Nov 14 10:00:07 Magistrala local2.info chat[3082]: send ( ^M)
Nov 14 10:00:07 Magistrala daemon.info pppd[3078]: Serial connection established.
Nov 14 10:00:07 Magistrala daemon.info pppd[3078]: Using interface 3g-wan
Nov 14 10:00:07 Magistrala daemon.notice pppd[3078]: Connect: 3g-wan <--> /dev/ttyUSB0
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: reading /tmp/resolv.conf.auto
Nov 14 10:00:08 Magistrala daemon.warn dnsmasq[1943]: ignoring nameserver 192.168.1.1 - local interface
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain micro
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain micro
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain micro
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain oss
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain oss
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain oss
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain null
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain null
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain null
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain ing
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain ing
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain ing
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain indy
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain indy
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain indy
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain gopher
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain gopher
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain gopher
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain geek
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain geek
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain geek
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain fur
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain fur
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain fur
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain free
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain free
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain free
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain bbs
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain bbs
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain bbs
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain dyn
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain dyn
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain dyn
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain parody
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain parody
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain parody
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain glue
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain glue
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain glue
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 176.58.118.172#53 for domain bit
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 106.187.47.17#53 for domain bit
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using nameserver 178.32.31.41#53 for domain bit
Nov 14 10:00:08 Magistrala daemon.info dnsmasq[1943]: using local addresses only for domain lan
Nov 14 10:00:08 Magistrala daemon.info pppd[3078]: CHAP authentication succeeded
Nov 14 10:00:08 Magistrala daemon.notice pppd[3078]: CHAP authentication succeeded
Nov 14 10:00:14 Magistrala daemon.warn pppd[3078]: Could not determine remote IP address: defaulting to 10.64.64.64
Nov 14 10:00:14 Magistrala daemon.notice pppd[3078]: local IP address 37.108.147.127
Nov 14 10:00:14 Magistrala daemon.notice pppd[3078]: remote IP address 10.64.64.64
Nov 14 10:00:14 Magistrala daemon.notice pppd[3078]: primary DNS address 79.163.127.70
Nov 14 10:00:14 Magistrala daemon.notice pppd[3078]: secondary DNS address 217.116.100.65
Nov 14 10:00:14 Magistrala daemon.notice netifd: Interface 'wan' is now up
Nov 14 10:00:15 Magistrala user.notice ifup: Enabling Router Solicitations on wan (3g-wan)
Nov 14 10:00:15 Magistrala user.info firewall: removing wan (3g-wan) from zone wan
Nov 14 10:00:16 Magistrala user.info firewall: adding wan (3g-wan) to zone wan
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: reading /tmp/resolv.conf.auto
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 79.163.127.70#53
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 217.116.100.65#53
Nov 14 10:00:19 Magistrala daemon.warn dnsmasq[1943]: ignoring nameserver 192.168.1.1 - local interface
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain micro
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain micro
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain micro
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain oss
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain oss
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain oss
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain null
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain null
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain null
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain ing
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain ing
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain ing
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain indy
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain indy
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain indy
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain gopher
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain gopher
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain gopher
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain geek
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain geek
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain geek
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain fur
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain fur
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain fur
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain free
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain free
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain free
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain bbs
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain bbs
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain bbs
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain dyn
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain dyn
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain dyn
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain parody
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain parody
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain parody
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.142.171.235#53 for domain glue
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 95.211.32.162#53 for domain glue
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 66.244.95.20#53 for domain glue
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 176.58.118.172#53 for domain bit
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 106.187.47.17#53 for domain bit
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using nameserver 178.32.31.41#53 for domain bit
Nov 14 10:00:19 Magistrala daemon.info dnsmasq[1943]: using local addresses only for domain lan
Nov 14 10:00:23 Magistrala authpriv.info dropbear[3408]: Child connection from 192.168.1.2:58832
Nov 14 10:00:29 Magistrala kern.info kernel: [ 271.350000] IMQ driver unloaded successfully.
Nov 14 10:00:29 Magistrala kern.info kernel: [ 271.380000] Hooked IMQ after mangle on INPUT
Nov 14 10:00:29 Magistrala kern.info kernel: [ 271.390000] Hooked IMQ after mangle on FORWARD
Nov 14 10:00:29 Magistrala kern.info kernel: [ 271.390000] IMQ driver loaded successfully. (numdevs = 1, numqueues = 1)
Nov 14 10:00:34 Magistrala authpriv.info dropbear[3408]: Exit before auth: Exited normally
Nov 14 10:00:42 Magistrala authpriv.info dropbear[3848]: Child connection from 192.168.1.2:58833
Nov 14 10:01:01 Magistrala authpriv.notice dropbear[3848]: Password auth succeeded for 'root' from 192.168.1.2:58833

Cezary · 2012-11-14 10:12:25

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Trochę wcześniej potrzebuję. Wyłącz w gui 3g, i "używaj opennic", reboot i zrób logread

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 10:27:22

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Mam nadzieję, że znów czegoś nie ucięło:

root@Magistrala:~# logread
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 0.000000] Kernel command line: board=TL-MR3420 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan 1 01:00:43 Magistrala kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan 1 01:00:43 Magistrala kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] Memory: 28980k/32768k available (2225k kernel code, 3788k reserved, 423k data, 212k init, 0k highmem)
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] NR_IRQS:51
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.080000] Mount-cache hash table entries: 512
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.090000] NET: Registered protocol family 16
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.100000] MIPS: machine is TP-LINK TL-MR3420
Jan 1 01:00:43 Magistrala kern.warn kernel: [ 0.500000] registering PCI controller with io_map_base unset
Jan 1 01:00:43 Magistrala kern.info kernel: [ 0.540000] bio: create slab <bio-0> at 0
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 9.710000] JFFS2 notice: (458) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 23 of xref (0 dead, 10 orphan) found.
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 10.420000] SCSI subsystem initialized
Jan 1 01:00:43 Magistrala kern.info kernel: [ 10.580000] usbcore: registered new interface driver usbfs
Jan 1 01:00:43 Magistrala kern.info kernel: [ 10.590000] usbcore: registered new interface driver hub
Jan 1 01:00:43 Magistrala kern.info kernel: [ 10.600000] usbcore: registered new device driver usb
Jan 1 01:00:43 Magistrala kern.info kernel: [ 10.980000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 01:00:43 Magistrala kern.info kernel: [ 10.980000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Jan 1 01:00:43 Magistrala kern.info kernel: [ 10.990000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.030000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.050000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.050000] hub 1-0:1.0: USB hub found
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.060000] hub 1-0:1.0: 1 port detected
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.080000] Initializing USB Mass Storage driver...
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.080000] usbcore: registered new interface driver usb-storage
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.090000] USB Mass Storage support registered.
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.380000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.530000] hub 1-1:1.0: USB hub found
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.530000] hub 1-1:1.0: 4 ports detected
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.820000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
Jan 1 01:00:43 Magistrala kern.info kernel: [ 11.940000] scsi0 : usb-storage 1-1.1:1.5
Jan 1 01:00:43 Magistrala kern.info kernel: [ 12.020000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
Jan 1 01:00:43 Magistrala kern.info kernel: [ 12.130000] scsi1 : usb-storage 1-1.2:1.0
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 12.940000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 13.130000] scsi 1:0:0:0: Direct-Access ChipsBnk Flash Disk 4082 PQ: 0 ANSI: 2
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 13.140000] sd 1:0:0:0: [sda] 15548416 512-byte logical blocks: (7.96 GB/7.41 GiB)
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 13.150000] sd 1:0:0:0: [sda] Write Protect is off
Jan 1 01:00:43 Magistrala kern.debug kernel: [ 13.150000] sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
Jan 1 01:00:43 Magistrala kern.err kernel: [ 13.150000] sd 1:0:0:0: [sda] No Caching mode page present
Jan 1 01:00:43 Magistrala kern.err kernel: [ 13.160000] sd 1:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:43 Magistrala kern.err kernel: [ 13.170000] sd 1:0:0:0: [sda] No Caching mode page present
Jan 1 01:00:43 Magistrala kern.err kernel: [ 13.180000] sd 1:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:43 Magistrala kern.info kernel: [ 13.180000] sda: sda1 sda2
Jan 1 01:00:43 Magistrala kern.err kernel: [ 13.190000] sd 1:0:0:0: [sda] No Caching mode page present
Jan 1 01:00:43 Magistrala kern.err kernel: [ 13.200000] sd 1:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:43 Magistrala kern.notice kernel: [ 13.200000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Jan 1 01:00:43 Magistrala kern.info kernel: [ 35.870000] EXT4-fs (sda2): recovery complete
Jan 1 01:00:43 Magistrala kern.info kernel: [ 35.870000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
Jan 1 01:00:43 Magistrala kern.info kernel: [ 36.060000] eth0: link down
Jan 1 01:00:43 Magistrala kern.info kernel: [ 36.690000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
Jan 1 01:00:43 Magistrala kern.info kernel: [ 36.690000] Backport based on wireless-testing.git master-2012-09-07
Jan 1 01:00:43 Magistrala kern.info kernel: [ 36.700000] compat.git: wireless-testing.git
Jan 1 01:00:43 Magistrala kern.info kernel: [ 36.870000] cfg80211: Calling CRDA to update world regulatory domain
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.880000] cfg80211: World regulatory domain updated:
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.880000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.900000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.910000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.910000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 36.920000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.warn kernel: [ 37.820000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ath: EEPROM regdomain: 0x0
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ath: EEPROM indicates default country code should be used
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ath: doing EEPROM country->regdmn map search
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ath: country maps to regdmn code: 0x3a
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ath: Country alpha2 being used: US
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ath: Regpair used: 0x3a
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan 1 01:00:44 Magistrala kern.debug kernel: [ 37.830000] Registered led device: ath9k-phy0
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.830000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=40
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.840000] cfg80211: Calling CRDA for country: US
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.850000] cfg80211: Regulatory domain changed to country: US
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.870000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.880000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.880000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:44 Magistrala kern.info kernel: [ 37.890000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:46 Magistrala user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB_2.0_Hub_[MTT] Serial=?
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1.1:1.1: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1.1:1.2: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1.1:1.3: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1.1:1.4: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Jan 1 01:00:47 Magistrala user.notice usb-modeswitch: 1-1.1:1.5: Manufacturer=Huawei_Technologies Product=HUAWEI_Mobile Serial=?
Jan 1 01:00:48 Magistrala user.notice usb-modeswitch: 1-1.2:1.0: Manufacturer=ChipsBnk Product=Flash_Disk Serial=013244704081
Jan 1 01:00:48 Magistrala kern.info kernel: [ 48.060000] device eth0 entered promiscuous mode
Jan 1 01:00:48 Magistrala daemon.notice netifd: Interface 'lan' is now up
Jan 1 01:00:48 Magistrala daemon.notice netifd: Interface 'loopback' is now up
Jan 1 01:00:48 Magistrala user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Jan 1 01:00:48 Magistrala kern.info kernel: [ 48.660000] eth0: link up (1000Mbps/Full duplex)
Jan 1 01:00:48 Magistrala kern.info kernel: [ 48.660000] br-lan: port 1(eth0) entered forwarding state
Jan 1 01:00:48 Magistrala kern.info kernel: [ 48.670000] br-lan: port 1(eth0) entered forwarding state
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.430000] cfg80211: Calling CRDA for country: PL
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.430000] cfg80211: Regulatory domain changed to country: PL
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.440000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.470000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
Jan 1 01:00:50 Magistrala kern.info kernel: [ 50.670000] br-lan: port 1(eth0) entered forwarding state
Nov 14 00:00:04 Magistrala user.info sysinit: Loading defaults
Nov 14 00:00:04 Magistrala user.info sysinit: Loading synflood protection
Nov 14 00:00:04 Magistrala user.info sysinit: Adding custom chains
Nov 14 00:00:05 Magistrala user.info sysinit: Loading zones
Nov 14 00:00:06 Magistrala user.info sysinit: Loading forwardings
Nov 14 00:00:06 Magistrala user.info sysinit: Loading rules
Nov 14 00:00:07 Magistrala user.info sysinit: Loading redirects
Nov 14 00:00:07 Magistrala user.info sysinit: Loading includes
Nov 14 00:00:08 Magistrala user.info sysinit: uci: Entry not found
Nov 14 00:00:08 Magistrala user.info sysinit: Optimizing conntrack
Nov 14 00:00:08 Magistrala user.info sysinit: Loading interfaces
Nov 14 00:00:08 Magistrala user.info firewall: adding lan (br-lan) to zone lan
Nov 14 00:00:11 Magistrala authpriv.info dropbear[1639]: Running in background
Nov 14 00:00:12 Magistrala daemon.warn httpd_gargoyle[1675]: started as root without requesting chroot(), warning only
Nov 14 00:00:12 Magistrala daemon.notice httpd_gargoyle[1675]: httpd_gargoyle/1.0 14mar2008 starting on Magistrala, port 5854
Nov 14 00:00:13 Magistrala user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Nov 14 00:00:13 Magistrala user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Nov 14 00:00:17 Magistrala daemon.info dnsmasq[1852]: started, version 2.62 cachesize 150
Nov 14 00:00:17 Magistrala daemon.info dnsmasq[1852]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Nov 14 00:00:17 Magistrala daemon.info dnsmasq-dhcp[1852]: DHCP, IP range 192.168.1.2 -- 192.168.1.254, lease time 12h
Nov 14 00:00:17 Magistrala daemon.info dnsmasq[1852]: using local addresses only for domain lan
Nov 14 00:00:17 Magistrala daemon.info dnsmasq[1852]: reading /tmp/resolv.conf.auto
Nov 14 00:00:17 Magistrala daemon.warn dnsmasq[1852]: ignoring nameserver 192.168.1.1 - local interface
Nov 14 00:00:17 Magistrala daemon.info dnsmasq[1852]: using local addresses only for domain lan
Nov 14 00:00:17 Magistrala daemon.info dnsmasq[1852]: read /etc/hosts - 4 addresses
Nov 14 00:00:17 Magistrala daemon.info dnsmasq-dhcp[1852]: read /etc/ethers - 1 addresses
Nov 14 00:00:17 Magistrala user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Nov 14 00:00:17 Magistrala user.info sysinit: (Did you specify correct configuration file path?)
Nov 14 00:00:17 Magistrala kern.warn kernel: [ 68.490000] head: sending ioctl 540d to a partition!
Nov 14 00:00:17 Magistrala kern.warn kernel: [ 68.490000] head: sending ioctl 540d to a partition!
Nov 14 00:00:18 Magistrala user.info sysinit: setting up led USB
Nov 14 00:00:19 Magistrala user.notice fstab: mount: mounting /dev/sda1 on /mnt/sda1 failed: Invalid argument
Nov 14 00:00:19 Magistrala kern.warn kernel: [ 69.860000] head: sending ioctl 540d to a partition!
Nov 14 00:00:19 Magistrala kern.warn kernel: [ 69.860000] head: sending ioctl 540d to a partition!
Nov 14 00:00:20 Magistrala kern.warn kernel: [ 71.590000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
Nov 14 00:00:20 Magistrala kern.warn kernel: [ 71.590000] old minutes west=0, new minutes west=-60
Nov 14 00:00:49 Magistrala authpriv.info dropbear[2432]: Child connection from 192.168.1.2:58929
Nov 14 00:00:53 Magistrala user.notice ifup: Enabling Router Solicitations on loopback (lo)
Nov 14 00:01:08 Magistrala authpriv.notice dropbear[2432]: Password auth succeeded for 'root' from 192.168.1.2:58929

Polarus · 2012-11-14 10:47:33

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Wydarzyła się rzecz dziwna: teraz, nagle po wyłączeniu 3G i Open NIc wszystko się pozmieniało:

root@Magistrala:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/sda2 on /overlay type ext4 (rw,noatime,user_xattr,barrier=1,data=ordered)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
root@Magistrala:~# df -h
Filesystem Size Used Available Use% Mounted on
rootfs 7.3G 237.8M 7.0G 3% /
/dev/root 2.8M 2.8M 0 100% /rom
tmpfs 14.3M 84.0K 14.2M 1% /tmp
tmpfs 512.0K 0 512.0K 0% /dev
/dev/sda2 7.3G 237.8M 7.0G 3% /overlay
overlayfs:/overlay 7.3G 237.8M 7.0G 3% /

Czyli teraz niby nagle wszystko działa, ale dopiero po wyłączeniu 3G i Open NIC

Cezary · 2012-11-14 11:13:15

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Bo teraz masz go. Wywal opcję device z konfiga, zostaw samo uuid.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 12:21:26

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

No niestety... nie pomogło. Ale za to zrealizowałem na czym polega problem:
Czytnik SD i modem są podłączone do huba. Niestety, przy odpaleniu listwy nie chce się to poprawnie montować, natomiast po wykonaniu reboot wszystko chodzi. Tu muszę podkreślić, że nie było tego problemu na backfire, jak bym nie podłączył wszystko działało dobrze, chyba trzeba będzie rozważyć powrót do Backfire...
Oto log z podejscia, w którym nie zamontowało się to poprawnie:
root@magistrala:~# logread
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jan 1 01:00:39 magistrala kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jan 1 01:00:39 magistrala kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] Memory: 28980k/32768k available (2225k kernel code, 3788k reserved, 423k data, 212k init, 0k highmem)
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] NR_IRQS:51
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.080000] Mount-cache hash table entries: 512
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.090000] NET: Registered protocol family 16
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.100000] MIPS: machine is TP-LINK TL-MR3420
Jan 1 01:00:39 magistrala kern.warn kernel: [ 0.500000] registering PCI controller with io_map_base unset
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.540000] bio: create slab <bio-0> at 0
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.550000] PCI host bridge to bus 0000:00
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000]
Jan 1 01:00:39 magistrala kern.debug kernel: [ 0.560000] pci 0000:00:00.0: [168c:002e] type 0 class 0x000280
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.560000] pci 0000:00:00.0: fixup device configuration
Jan 1 01:00:39 magistrala kern.debug kernel: [ 0.570000] pci 0000:00:00.0: reg 10: [mem 0x10000000-0x1000ffff 64bit]
Jan 1 01:00:39 magistrala kern.debug kernel: [ 0.570000] pci 0000:00:00.0: supports D1
Jan 1 01:00:39 magistrala kern.debug kernel: [ 0.570000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
Jan 1 01:00:39 magistrala kern.info kernel: [ 0.570000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.050000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.050000] hub 1-0:1.0: USB hub found
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.060000] hub 1-0:1.0: 1 port detected
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.080000] Initializing USB Mass Storage driver...
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.080000] usbcore: registered new interface driver usb-storage
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.090000] USB Mass Storage support registered.
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.380000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.530000] hub 1-1:1.0: USB hub found
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.530000] hub 1-1:1.0: 4 ports detected
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.820000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
Jan 1 01:00:39 magistrala kern.info kernel: [ 11.930000] scsi0 : usb-storage 1-1.1:1.0
Jan 1 01:00:39 magistrala kern.info kernel: [ 12.020000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
Jan 1 01:00:39 magistrala kern.info kernel: [ 12.130000] scsi1 : usb-storage 1-1.2:1.0
Jan 1 01:00:39 magistrala kern.notice kernel: [ 12.940000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
Jan 1 01:00:39 magistrala kern.notice kernel: [ 13.130000] scsi 1:0:0:0: Direct-Access ChipsBnk Flash Disk 4082 PQ: 0 ANSI: 2
Jan 1 01:00:39 magistrala kern.notice kernel: [ 13.140000] sd 1:0:0:0: [sda] Attached SCSI removable disk
Jan 1 01:00:39 magistrala kern.info kernel: [ 17.690000] usb 1-1.1: USB disconnect, device number 3
Jan 1 01:00:39 magistrala kern.info kernel: [ 32.100000] eth0: link down
Jan 1 01:00:39 magistrala kern.info kernel: [ 32.800000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
Jan 1 01:00:39 magistrala kern.info kernel: [ 32.800000] Backport based on wireless-testing.git master-2012-09-07
Jan 1 01:00:39 magistrala kern.info kernel: [ 32.810000] compat.git: wireless-testing.git
Jan 1 01:00:39 magistrala kern.info kernel: [ 32.980000] cfg80211: Calling CRDA to update world regulatory domain
Jan 1 01:00:39 magistrala kern.info kernel: [ 32.990000] cfg80211: World regulatory domain updated:
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.000000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.010000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.020000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.030000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.030000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.warn kernel: [ 33.930000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ath: EEPROM regdomain: 0x0
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ath: EEPROM indicates default country code should be used
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ath: doing EEPROM country->regdmn map search
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ath: country maps to regdmn code: 0x3a
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ath: Country alpha2 being used: US
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ath: Regpair used: 0x3a
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jan 1 01:00:39 magistrala kern.debug kernel: [ 33.940000] Registered led device: ath9k-phy0
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.940000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=40
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.950000] cfg80211: Calling CRDA for country: US
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.960000] cfg80211: Regulatory domain changed to country: US
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.960000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.970000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.980000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.990000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 33.990000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 34.000000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 34.010000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Jan 1 01:00:39 magistrala kern.info kernel: [ 34.240000] PPP generic driver version 2.4.2
Jan 1 01:00:39 magistrala kern.info kernel: [ 34.480000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 01:00:39 magistrala kern.info kernel: [ 34.890000] NET: Registered protocol family 24
Jan 1 01:00:39 magistrala kern.info kernel: [ 35.050000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Jan 1 01:00:39 magistrala kern.info kernel: [ 36.340000] xt_time: kernel timezone is -0000
Jan 1 01:00:39 magistrala kern.info kernel: [ 36.850000] Hooked IMQ after mangle on PREROUTING
Jan 1 01:00:39 magistrala kern.info kernel: [ 36.850000] Hooked IMQ after nat on POSTROUTING
Jan 1 01:00:39 magistrala kern.info kernel: [ 36.860000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.090000] Netfilter messages via NETLINK v0.30.
Jan 1 01:00:39 magistrala kern.notice kernel: [ 37.150000] ip_set: protocol 6
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.830000] usbcore: registered new interface driver cdc_acm
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.840000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.970000] usbcore: registered new interface driver usbserial
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.980000] USB Serial support registered for generic
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.980000] usbcore: registered new interface driver usbserial_generic
Jan 1 01:00:39 magistrala kern.info kernel: [ 37.990000] usbserial: USB Serial Driver core
Jan 1 01:00:42 magistrala user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
Jan 1 01:00:42 magistrala user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB_2.0_Hub_[MTT] Serial=?
Jan 1 01:00:43 magistrala user.notice usb-modeswitch: 1-1.2:1.0: Manufacturer=ChipsBnk Product=Flash_Disk Serial=013244704081
Jan 1 01:00:43 magistrala daemon.notice netifd: Interface 'lan' is now up
Jan 1 01:00:43 magistrala kern.info kernel: [ 43.690000] device eth0 entered promiscuous mode
Jan 1 01:00:43 magistrala daemon.notice netifd: Interface 'loopback' is now up
Jan 1 01:00:44 magistrala user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Jan 1 01:00:44 magistrala kern.info kernel: [ 44.790000] eth0: link up (1000Mbps/Full duplex)
Jan 1 01:00:44 magistrala kern.info kernel: [ 44.790000] br-lan: port 1(eth0) entered forwarding state
Jan 1 01:00:44 magistrala kern.info kernel: [ 44.800000] br-lan: port 1(eth0) entered forwarding state
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.090000] cfg80211: Calling CRDA for country: PL
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.090000] cfg80211: Regulatory domain changed to country: PL
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.100000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.110000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.120000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.130000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
Jan 1 01:00:46 magistrala kern.info kernel: [ 46.800000] br-lan: port 1(eth0) entered forwarding state
Jan 1 01:00:04 magistrala user.info sysinit: Loading defaults
Jan 1 01:00:05 magistrala user.info sysinit: Loading synflood protection
Jan 1 01:00:05 magistrala user.info sysinit: Adding custom chains
Jan 1 01:00:06 magistrala user.info sysinit: Loading zones
Jan 1 01:00:07 magistrala user.info sysinit: Loading forwardings
Jan 1 01:00:07 magistrala user.info sysinit: Loading rules
Jan 1 01:00:08 magistrala user.info sysinit: Loading redirects
Jan 1 01:00:08 magistrala user.info sysinit: Loading includes
Jan 1 01:00:09 magistrala user.info sysinit: uci: Entry not found
Jan 1 01:00:09 magistrala user.info sysinit: Optimizing conntrack
Jan 1 01:00:09 magistrala user.info sysinit: Loading interfaces
Jan 1 01:00:10 magistrala user.info firewall: adding lan (br-lan) to zone lan
Jan 1 01:00:11 magistrala kern.notice kernel: [ 57.930000] sd 1:0:0:0: [sda] 15548416 512-byte logical blocks: (7.96 GB/7.41 GiB)
Jan 1 01:00:11 magistrala kern.err kernel: [ 57.950000] sd 1:0:0:0: [sda] No Caching mode page present
Jan 1 01:00:11 magistrala kern.err kernel: [ 57.950000] sd 1:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:11 magistrala kern.err kernel: [ 57.970000] sd 1:0:0:0: [sda] No Caching mode page present
Jan 1 01:00:11 magistrala kern.err kernel: [ 57.970000] sd 1:0:0:0: [sda] Assuming drive cache: write through
Jan 1 01:00:11 magistrala kern.info kernel: [ 57.980000] sda: sda1 sda2
Jan 1 01:00:12 magistrala authpriv.info dropbear[1646]: Running in background
Jan 1 01:00:12 magistrala authpriv.info dropbear[1667]: Child connection from 192.168.1.2:59303
Jan 1 01:00:13 magistrala daemon.warn httpd_gargoyle[1701]: started as root without requesting chroot(), warning only
Jan 1 01:00:13 magistrala daemon.notice httpd_gargoyle[1701]: httpd_gargoyle/1.0 14mar2008 starting on magistrala, port 5854
Jan 1 01:00:14 magistrala user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jan 1 01:00:14 magistrala user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jan 1 01:00:16 magistrala kern.warn kernel: [ 63.100000] head: sending ioctl 540d to a partition!
Jan 1 01:00:16 magistrala kern.warn kernel: [ 63.100000] head: sending ioctl 540d to a partition!
Jan 1 01:00:17 magistrala daemon.info dnsmasq[1864]: started, version 2.62 cachesize 150
Jan 1 01:00:17 magistrala daemon.info dnsmasq[1864]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jan 1 01:00:17 magistrala daemon.info dnsmasq-dhcp[1864]: DHCP, IP range 192.168.1.2 -- 192.168.1.254, lease time 12h
Jan 1 01:00:17 magistrala daemon.info dnsmasq[1864]: using local addresses only for domain lan
Jan 1 01:00:17 magistrala daemon.info dnsmasq[1864]: reading /tmp/resolv.conf.auto
Jan 1 01:00:17 magistrala daemon.warn dnsmasq[1864]: ignoring nameserver 192.168.1.1 - local interface
Jan 1 01:00:17 magistrala daemon.info dnsmasq[1864]: using local addresses only for domain lan
Jan 1 01:00:17 magistrala daemon.info dnsmasq[1864]: read /etc/hosts - 4 addresses
Jan 1 01:00:17 magistrala daemon.info dnsmasq-dhcp[1864]: read /etc/ethers - 1 addresses
Jan 1 01:00:18 magistrala user.info sysinit: ERROR: No valid dynamic DNS service configurations defined
Jan 1 01:00:18 magistrala user.info sysinit: (Did you specify correct configuration file path?)
Jan 1 01:00:18 magistrala user.info sysinit: setting up led USB
Jan 1 01:00:18 magistrala user.notice fstab: mount: mounting /dev/sda1 on /mnt/sda1 failed: Invalid argument
Jan 1 01:00:19 magistrala kern.warn kernel: [ 65.350000] head: sending ioctl 540d to a partition!
Jan 1 01:00:19 magistrala kern.warn kernel: [ 65.350000] head: sending ioctl 540d to a partition!
Jan 1 01:00:20 magistrala kern.warn kernel: [ 67.310000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
Jan 1 01:00:20 magistrala kern.warn kernel: [ 67.320000] old minutes west=0, new minutes west=-60
Jan 1 01:00:21 magistrala kern.info kernel: [ 67.600000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
Jan 1 01:00:21 magistrala authpriv.notice dropbear[1667]: Password auth succeeded for 'root' from 192.168.1.2:59303

Cezary · 2012-11-14 12:31:32

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Ponieważ na początku nie wykrywa Ci partycji!

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 12:36:41

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

A można wiedzieć, czemu w Backfire nie ma z tym problemów?

Cezary · 2012-11-14 12:42:48

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Właśnie dobre pytanie. A jak przez huba podłączysz sam pendrive bez modemu to są one widoczne?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 12:48:19

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Próbowałem bez modemu, dzieje się to samo. Jeszcze spróbuje bez huba.

cityboy · 2012-11-14 12:51:42

cityboy
Użytkownik
Nieaktywny

Zarejestrowany: 2011-01-13
Posty: 190

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Zdaje się ze mamy podobny problem ....
ja walczę z exrootem na dysku zewnętrznym

Filesystem                Size      Used Available Use% Mounted on
rootfs                  384.0K    352.0K     32.0K  92% /
/dev/root                 2.8M      2.8M         0 100% /rom
tmpfs                    14.3M    124.0K     14.1M   1% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/mtdblock3          139.3G      2.2G    130.2G   2% /overlay
overlayfs:/overlay      384.0K    352.0K     32.0K  92% /
/dev/sda1               139.3G      2.2G    130.2G   2% /overlay

też podłączonym do huba aktywnego

Pc Engines APU2 OpenWrt 18.06-SNAPSHOT r7714-4918fe0291

Polarus · 2012-11-14 12:54:16

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Niestety, bez huba to samo. Za pierwszym razem nie, po reboot montuje wszystko poprawnie.

Cezary · 2012-11-14 12:57:01

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

To jeszcze zobacz AA z openwrt.org. Jak jest to samo - złość ticketa, a ja sprawdzę wieczorem pewien pomysł na to.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 16:30:00

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Nie mam jak sprawdzić, bo to ustrojstwo z openwrt nie posiada pakietów a jedyną opcją internetu jaką mam przy sobie jest 3g. Próbowałem też ustawić żeby próbował przez windowsowe udostępnianie połączenia ale przyznam szczerze że nie potrafię, bo wspaniałomyslny Microsoft nie zapewnia nawet serwera DHCP w Windowsie, a z kolei gdy poustawiam adresy na sztywno to komputer z WAN-em w routerze się nie widzą... Cały dzień dłubaniny... Załamka, kompletnie nic nie zdziałałem... Mimo wszystko dzięki wielkie za pomoc, jakbys wiedział jak to najprościej podłączyć do internetu by pakiety pobrać - byłbym wdzięczny.

Cezary · 2012-11-14 16:32:32

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

To zainstaluj gargoyle, tam już wszystko masz w sumie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Polarus · 2012-11-14 20:01:42

Polarus
Użytkownik
Nieaktywny

Zarejestrowany: 2011-08-03
Posty: 56

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Update: udało się z połączeniem i doinstalowaniem pakietów, jednak w OpenWRT nic nie chce mi się w ogóle montować mimo pakietu block-mount, sterowników USB, i systemów plików. To chyba dla mnie już zbyt skomplikowane, cokolwiek nie chciałbym zamontować pokazuje że nie znaleziono czegoś takiego w /etc/fstab

Próbuję instalować czysty gargoyle, może sobie dam radę.

edit: nie ma tu nawet fstab (block-mount)...
Wracam do backfire, poświęciłem na to wszystko cały dzień, niestety bez zupełnie żadnego rezultatu. Próbuję zainstalować pakiet kmod-usb-storage lub inne:

* satisfy_dependencies_for: Cannot satisfy the following dependencies for kmod-usb-uhci:
* kernel (= 3.3.8-1-54676ff21e7e4e275e485bc50fb94fcb) *
* opkg_install_cmd: Cannot install package kmod-usb-storage.|
* opkg_install_cmd: Cannot install package kmod-usb-uhci.|
i tak dalej...

Zbyt zawiłe dla mnie, za dużo rzeczy nie działa tak jak trzeba albo w ogóle nie działa...
Teraz widzę wyższość używania Twoich buildów nad tymi badziewnymi z openwrt czy gargoyle, w Twoich jeśli to tylko możliwe wszystko działa bez zarzutu, a jeśli nawet cos jest źle - naprawiasz to na bieżąco... Twoje pakiety mają wszystko czego trzeba - tu nawet nie ma fstaba, by zamontować extroota... Inna sprawa to, że zawsze pomagasz kiedy tylko możesz, tam różnie z tym supportem...

Będę śledził ten wątek, czy coś w kwestii extroota się coś zmieniło, tymczasem czas powrócić do backfire. Ja muszę miec wszystko działające dziś przed 23:00.
Chciałem pomóc Tobie i innym w zidentyfikowaniu problemu ale widać nie nadaję się do tego.
Serdeczne pozdrowienia.

lucpo · 2012-11-15 23:42:55

lucpo
Użytkownik
Nieaktywny

Zarejestrowany: 2011-12-31
Posty: 22

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Mam podobny problem z extrootem. Nie działa

root@OpenWrt:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime,size=14620k)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
/dev/sda2 on /overlay type ext4 (rw,noatime,user_xattr,barrier=1,data=ordered)
/dev/sda3 on /mnt/sda3 type ext4 (rw,relatime,user_xattr,barrier=1,data=ordered)
root@OpenWrt:~# df -h
Filesystem                Size      Used Available Use% Mounted on
rootfs                    4.8M      2.4M      2.3M  51% /
/dev/root                 2.3M      2.3M         0 100% /rom
tmpfs                    14.3M     80.0K     14.2M   1% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/mtdblock3          311.1M     17.3M    293.8M   6% /overlay
overlayfs:/overlay        4.8M      2.4M      2.3M  51% /
/dev/sda2               311.1M     17.3M    293.8M   6% /overlay
/dev/sda3               558.5G    473.1G     55.6G  89% /mnt/sda3

Fstab

config mount
    option fstype ext4
    option options rw,noatime
    option enabled 1
    option uuid ef2ba5b7-22e1-4101-bff4-716f7b715015
    option target /overlay
    option enabled_fsck 0

Jakiś pomysł?

Cezary · 2012-11-16 06:21:17

Cezary
...
Nieaktywny

Skąd: Warszawa
Zarejestrowany: 2006-02-25
Posty: 116,280

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

pokaż:
ls /etc/rc.d
blkid /dev/sda2
logread od samego startu routera

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

lucpo · 2012-11-16 15:47:17

lucpo
Użytkownik
Nieaktywny

Zarejestrowany: 2011-12-31
Posty: 22

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

proszę

root@OpenWrt:~# ls /etc/rc.d
K19portmap            K99umount             S20fstab              S50telnet             S96led
K50dropbear           S05defconfig          S20network            S50uhttpd             S97watchdog
K60nfsd               S05luci_fixtime       S39usb                S59luci_dhcp_migrate  S98sysntpd
K90network            S10boot               S45firewall           S60dnsmasq            S99sysctl
K95luci_fixtime       S11ubus               S50cron               S60nfsd
K98boot               S19portmap            S50dropbear           S95done
root@OpenWrt:~#
root@OpenWrt:~# blkid /dev/sda2
/dev/sda2: UUID="ef2ba5b7-22e1-4101-bff4-716f7b715015" TYPE="ext4"

Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.390000] TCP: Hash tables configured (established 1024 bind 1024)
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.400000] TCP reno registered
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.420000] NET: Registered protocol family 1
Nov 16 15:41:04 OpenWrt kern.debug kernel: [    0.420000] PCI: CLS 0 bytes, default 32
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.450000] msgmni has been set to 56
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.470000] io scheduler noop registered
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.470000] io scheduler deadline registered (default)
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.510000] console [ttyS0] enabled, bootconsole disabled
Nov 16 15:41:04 OpenWrt kern.warn kernel: [    0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.540000] 5 tp-link partitions found on MTD device spi0.0
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.540000] Creating 5 MTD partitions on "spi0.0":
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.550000] 0x000000000000-0x000000020000 : "u-boot"
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.560000] 0x000000020000-0x00000010a000 : "kernel"
Nov 16 15:41:04 OpenWrt kern.warn kernel: [    0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.580000] 0x00000010a000-0x0000007f0000 : "rootfs"
Nov 16 15:41:04 OpenWrt kern.warn kernel: [    0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.590000] mtd: partition "rootfs" set to be root filesystem
Nov 16 15:41:04 OpenWrt kern.info kernel: [    0.600000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=4C0000 
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.610000] 0x000000330000-0x0000007f0000 : "rootfs_data"
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.620000] 0x0000007f0000-0x000000800000 : "art"
Nov 16 15:41:04 OpenWrt kern.notice kernel: [    0.620000] 0x000000020000-0x0000007f0000 : "firmware"
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.050000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.060000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.070000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.300000] RPC: Registered named UNIX socket transport module.
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.310000] RPC: Registered udp transport module.
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.310000] RPC: Registered tcp transport module.
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.320000] RPC: Registered tcp NFSv4.1 backchannel transport module.
Nov 16 15:41:04 OpenWrt kern.info kernel: [   31.810000] PPP generic driver version 2.4.2
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.040000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.400000] NET: Registered protocol family 24
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.450000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.820000] usbcore: registered new interface driver ums-alauda
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.840000] scsi0 : usb-storage 1-1:1.0
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.850000] usbcore: registered new interface driver ums-cypress
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.870000] usbcore: registered new interface driver ums-datafab
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.890000] usbcore: registered new interface driver ums-freecom
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.920000] usbcore: registered new interface driver ums-isd200
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.940000] usbcore: registered new interface driver ums-jumpshot
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.960000] usbcore: registered new interface driver ums-karma
Nov 16 15:41:04 OpenWrt kern.info kernel: [   32.990000] usbcore: registered new interface driver ums-sddr09
Nov 16 15:41:04 OpenWrt kern.info kernel: [   33.010000] usbcore: registered new interface driver ums-sddr55
Nov 16 15:41:04 OpenWrt kern.info kernel: [   33.040000] usbcore: registered new interface driver ums-usbat
Nov 16 15:41:07 OpenWrt kern.debug kernel: [   36.640000] ar71xx: pll_reg 0xb8050014: 0x1a000000
Nov 16 15:41:07 OpenWrt daemon.notice netifd: Interface 'lan' is now up
Nov 16 15:41:07 OpenWrt daemon.notice netifd: Interface 'loopback' is now up
Nov 16 15:41:08 OpenWrt daemon.info pppd[744]: Plugin rp-pppoe.so loaded.
Nov 16 15:41:08 OpenWrt daemon.info pppd[744]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
Nov 16 15:41:08 OpenWrt daemon.notice pppd[744]: pppd 2.4.5 started by root, uid 0
Nov 16 15:41:08 OpenWrt kern.info kernel: [   36.940000] eth0: link up (1000Mbps/Full duplex)
Nov 16 15:41:08 OpenWrt kern.info kernel: [   36.950000] device eth0.1 entered promiscuous mode
Nov 16 15:41:08 OpenWrt kern.info kernel: [   36.950000] device eth0 entered promiscuous mode
Nov 16 15:41:08 OpenWrt kern.info kernel: [   36.970000] br-lan: port 1(eth0.1) entered forwarding state
Nov 16 15:41:08 OpenWrt kern.info kernel: [   36.970000] br-lan: port 1(eth0.1) entered forwarding state
Nov 16 15:41:08 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Nov 16 15:41:09 OpenWrt kern.info kernel: [   38.970000] br-lan: port 1(eth0.1) entered forwarding state
Nov 16 15:41:10 OpenWrt kern.notice kernel: [   40.270000] scsi 0:0:0:0: Direct-Access     SAMSUNG  HD642JJ               PQ: 0 ANSI: 0
Nov 16 15:41:10 OpenWrt kern.notice kernel: [   40.280000] sd 0:0:0:0: [sda] 1250261614 512-byte logical blocks: (640 GB/596 GiB)
Nov 16 15:41:10 OpenWrt kern.notice kernel: [   40.280000] sd 0:0:0:0: [sda] Write Protect is off
Nov 16 15:41:10 OpenWrt kern.debug kernel: [   40.290000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
Nov 16 15:41:10 OpenWrt kern.info kernel: [   40.300000] device wlan0 entered promiscuous mode
Nov 16 15:41:10 OpenWrt kern.err kernel: [   40.320000] sd 0:0:0:0: [sda] No Caching mode page present
Nov 16 15:41:10 OpenWrt kern.err kernel: [   40.320000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Nov 16 15:41:10 OpenWrt kern.err kernel: [   40.360000] sd 0:0:0:0: [sda] No Caching mode page present
Nov 16 15:41:10 OpenWrt kern.err kernel: [   40.360000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Nov 16 15:41:10 OpenWrt kern.info kernel: [   40.390000]  sda: sda1 sda2 sda3
Nov 16 15:41:10 OpenWrt kern.err kernel: [   40.400000] sd 0:0:0:0: [sda] No Caching mode page present
Nov 16 15:41:10 OpenWrt kern.err kernel: [   40.400000] sd 0:0:0:0: [sda] Assuming drive cache: write through
Nov 16 15:41:10 OpenWrt kern.notice kernel: [   40.410000] sd 0:0:0:0: [sda] Attached SCSI disk
Nov 16 15:41:11 OpenWrt kern.info kernel: [   41.430000] br-lan: port 2(wlan0) entered forwarding state
Nov 16 15:41:11 OpenWrt kern.info kernel: [   41.430000] br-lan: port 2(wlan0) entered forwarding state
Nov 16 15:41:11 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Nov 16 15:41:13 OpenWrt daemon.info pppd[744]: PPP session is 13158
Nov 16 15:41:13 OpenWrt daemon.warn pppd[744]: Connected to 00:90:1a:9f:f8:1d via interface eth0.2
Nov 16 15:41:13 OpenWrt daemon.info pppd[744]: Using interface pppoe-wan
Nov 16 15:41:13 OpenWrt daemon.notice pppd[744]: Connect: pppoe-wan <--> eth0.2
Nov 16 15:41:13 OpenWrt daemon.info pppd[744]: CHAP authentication failed: permission denied
Nov 16 15:41:13 OpenWrt daemon.err pppd[744]: CHAP authentication failed
Nov 16 15:41:13 OpenWrt daemon.notice pppd[744]: Connection terminated.
Nov 16 15:41:13 OpenWrt daemon.info pppd[744]: Exit.
Nov 16 15:41:13 OpenWrt kern.info kernel: [   43.430000] br-lan: port 2(wlan0) entered forwarding state
Nov 16 15:41:13 OpenWrt daemon.notice netifd: Interface 'wan' is now down
Nov 16 15:41:14 OpenWrt daemon.info pppd[1170]: Plugin rp-pppoe.so loaded.
Nov 16 15:41:14 OpenWrt daemon.info pppd[1170]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
Nov 16 15:41:14 OpenWrt daemon.notice pppd[1170]: pppd 2.4.5 started by root, uid 0
Nov 16 15:41:14 OpenWrt daemon.info pppd[1170]: PPP session is 13163
Nov 16 15:41:14 OpenWrt daemon.warn pppd[1170]: Connected to 00:90:1a:9f:f8:1d via interface eth0.2
Nov 16 15:41:14 OpenWrt daemon.info pppd[1170]: Using interface pppoe-wan
Nov 16 15:41:14 OpenWrt daemon.notice pppd[1170]: Connect: pppoe-wan <--> eth0.2
Nov 16 15:41:14 OpenWrt daemon.info hostapd: wlan0: STA 04:18:0f:18:60:84 IEEE 802.11: authenticated
Nov 16 15:41:14 OpenWrt daemon.info hostapd: wlan0: STA 04:18:0f:18:60:84 IEEE 802.11: associated (aid 1)
Nov 16 15:41:15 OpenWrt daemon.info pppd[1170]: CHAP authentication failed: permission denied
Nov 16 15:41:15 OpenWrt daemon.err pppd[1170]: CHAP authentication failed
Nov 16 15:41:15 OpenWrt daemon.info hostapd: wlan0: STA 04:18:0f:18:60:84 WPA: pairwise key handshake completed (RSN)
Nov 16 15:41:15 OpenWrt daemon.notice pppd[1170]: Connection terminated.
Nov 16 15:41:15 OpenWrt daemon.info pppd[1170]: Exit.
Nov 16 15:41:15 OpenWrt daemon.notice netifd: Interface 'wan' is now down
Nov 16 15:41:15 OpenWrt daemon.info pppd[1279]: Plugin rp-pppoe.so loaded.
Nov 16 15:41:15 OpenWrt daemon.info pppd[1279]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
Nov 16 15:41:15 OpenWrt daemon.notice pppd[1279]: pppd 2.4.5 started by root, uid 0
Nov 16 15:41:16 OpenWrt user.info sysinit: Loading defaults
Nov 16 15:41:16 OpenWrt user.info sysinit: Loading synflood protection
Nov 16 15:41:17 OpenWrt user.info sysinit: Adding custom chains
Nov 16 15:41:17 OpenWrt user.info sysinit: Loading zones
Nov 16 15:41:19 OpenWrt user.info sysinit: Loading forwardings
Nov 16 15:41:19 OpenWrt user.info sysinit: Loading rules
Nov 16 15:41:20 OpenWrt user.info sysinit: Loading redirects
Nov 16 15:41:20 OpenWrt user.info sysinit: Loading includes
Nov 16 15:41:20 OpenWrt user.info sysinit: Optimizing conntrack
Nov 16 15:41:20 OpenWrt user.info sysinit: Loading interfaces
Nov 16 15:41:20 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Nov 16 15:41:21 OpenWrt daemon.info pppd[1279]: PPP session is 13180
Nov 16 15:41:21 OpenWrt daemon.warn pppd[1279]: Connected to 00:90:1a:9f:f8:1d via interface eth0.2
Nov 16 15:41:21 OpenWrt daemon.info pppd[1279]: Using interface pppoe-wan
Nov 16 15:41:21 OpenWrt daemon.notice pppd[1279]: Connect: pppoe-wan <--> eth0.2
Nov 16 15:41:21 OpenWrt daemon.info pppd[1279]: CHAP authentication failed: permission denied
Nov 16 15:41:21 OpenWrt daemon.err pppd[1279]: CHAP authentication failed
Nov 16 15:41:21 OpenWrt authpriv.info dropbear[1632]: Running in background
Nov 16 15:41:22 OpenWrt kern.info kernel: [   52.390000] Adding 200776k swap on /dev/sda1.  Priority:-1 extents:1 across:200776k 
Nov 16 15:41:24 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Nov 16 15:41:24 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Nov 16 15:41:25 OpenWrt user.notice fstab: Mount enabled for /dev/sda2 but it doesn't have a defined mountpoint (target)
Nov 16 15:41:26 OpenWrt kern.err kernel: [   56.460000] EXT4-fs (sda3): couldn't mount as ext3 due to feature incompatibilities
Nov 16 15:41:26 OpenWrt kern.err kernel: [   56.470000] EXT4-fs (sda3): couldn't mount as ext2 due to feature incompatibilities
Nov 16 15:41:26 OpenWrt kern.warn kernel: [   56.530000] EXT4-fs (sda3): warning: maximal mount count reached, running e2fsck is recommended
Nov 16 15:41:26 OpenWrt kern.info kernel: [   56.540000] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
Nov 16 15:41:27 OpenWrt daemon.notice pppd[1279]: Connection terminated.
Nov 16 15:41:27 OpenWrt daemon.notice pppd[1279]: Modem hangup
Nov 16 15:41:27 OpenWrt daemon.info pppd[1279]: Exit.
Nov 16 15:41:27 OpenWrt daemon.notice netifd: Interface 'wan' is now down
Nov 16 15:41:27 OpenWrt daemon.info pppd[1935]: Plugin rp-pppoe.so loaded.
Nov 16 15:41:27 OpenWrt daemon.info pppd[1935]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
Nov 16 15:41:27 OpenWrt daemon.notice pppd[1935]: pppd 2.4.5 started by root, uid 0
Nov 16 15:41:28 OpenWrt daemon.info dnsmasq[1944]: started, version 2.62 cachesize 150
Nov 16 15:41:28 OpenWrt daemon.info dnsmasq[1944]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Nov 16 15:41:28 OpenWrt daemon.info dnsmasq-dhcp[1944]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Nov 16 15:41:28 OpenWrt daemon.info dnsmasq[1944]: using local addresses only for domain lan
Nov 16 15:41:28 OpenWrt daemon.warn dnsmasq[1944]: no servers found in /tmp/resolv.conf.auto, will retry
Nov 16 15:41:28 OpenWrt daemon.info dnsmasq[1944]: read /etc/hosts - 1 addresses
Nov 16 15:41:28 OpenWrt daemon.info dnsmasq-dhcp[1944]: read /etc/ethers - 0 addresses
Nov 16 15:41:28 OpenWrt daemon.info pppd[1935]: PPP session is 13194
Nov 16 15:41:28 OpenWrt daemon.warn pppd[1935]: Connected to 00:90:1a:9f:f8:1d via interface eth0.2
Nov 16 15:41:28 OpenWrt daemon.info pppd[1935]: Using interface pppoe-wan
Nov 16 15:41:28 OpenWrt daemon.notice pppd[1935]: Connect: pppoe-wan <--> eth0.2
Nov 16 15:41:28 OpenWrt daemon.notice rpc.statd[1965]: Version 1.2.6 starting
Nov 16 15:41:28 OpenWrt daemon.notice sm-notify[1966]: Version 1.2.6 starting
Nov 16 15:41:28 OpenWrt daemon.err sm-notify[1966]: Failed to open directory sm.bak: No such file or directory
Nov 16 15:41:28 OpenWrt daemon.notice rpc.statd[1965]: Initializing NSM state
Nov 16 15:41:28 OpenWrt daemon.warn rpc.statd[1965]: Running as root.  chown /var/lib/nfs to choose different user
Nov 16 15:41:28 OpenWrt daemon.notice rpc.mountd[1987]: Version 1.2.6 starting
Nov 16 15:41:28 OpenWrt daemon.info pppd[1935]: CHAP authentication failed: permission denied
Nov 16 15:41:28 OpenWrt daemon.err pppd[1935]: CHAP authentication failed
Nov 16 15:41:28 OpenWrt daemon.notice pppd[1935]: Connection terminated.
Nov 16 15:41:28 OpenWrt daemon.info pppd[1935]: Exit.
Nov 16 15:41:28 OpenWrt user.info sysinit: setting up led USB
Nov 16 15:41:28 OpenWrt user.info sysinit: setting up led WLAN
Nov 16 15:41:28 OpenWrt daemon.notice netifd: Interface 'wan' is now down
Nov 16 15:41:29 OpenWrt daemon.info pppd[2050]: Plugin rp-pppoe.so loaded.
Nov 16 15:41:29 OpenWrt daemon.info pppd[2050]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
Nov 16 15:41:29 OpenWrt daemon.notice pppd[2050]: pppd 2.4.5 started by root, uid 0

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Attitude Adjustment - extroot nie działa tak jak powinien (Strona 1 z 2)

Posty: 1 do 25 z 50

1 Temat przez Polarus 2012-11-14 08:58:32 (edytowany przez Polarus 2012-11-14 09:00:48)

Temat: Attitude Adjustment - extroot nie działa tak jak powinien

2 Odpowiedź przez zdzichu6969 2012-11-14 09:10:45

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

3 Odpowiedź przez Polarus 2012-11-14 09:14:16 (edytowany przez Polarus 2012-11-14 09:14:49)

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

4 Odpowiedź przez Cezary 2012-11-14 09:26:01

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

5 Odpowiedź przez Polarus 2012-11-14 09:28:13

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

6 Odpowiedź przez Cezary 2012-11-14 09:39:46

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

7 Odpowiedź przez Polarus 2012-11-14 10:03:40

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

8 Odpowiedź przez Cezary 2012-11-14 10:12:25

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

9 Odpowiedź przez Polarus 2012-11-14 10:27:22

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

10 Odpowiedź przez Polarus 2012-11-14 10:47:33

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

11 Odpowiedź przez Cezary 2012-11-14 11:13:15

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

12 Odpowiedź przez Polarus 2012-11-14 12:21:26

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

13 Odpowiedź przez Cezary 2012-11-14 12:31:32

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

14 Odpowiedź przez Polarus 2012-11-14 12:36:41

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

15 Odpowiedź przez Cezary 2012-11-14 12:42:48

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

16 Odpowiedź przez Polarus 2012-11-14 12:48:19

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

17 Odpowiedź przez cityboy 2012-11-14 12:51:42 (edytowany przez cityboy 2012-11-14 12:52:33)

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

18 Odpowiedź przez Polarus 2012-11-14 12:54:16

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

19 Odpowiedź przez Cezary 2012-11-14 12:57:01

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

20 Odpowiedź przez Polarus 2012-11-14 16:30:00

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

21 Odpowiedź przez Cezary 2012-11-14 16:32:32

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

22 Odpowiedź przez Polarus 2012-11-14 20:01:42 (edytowany przez Polarus 2012-11-14 21:02:14)

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

23 Odpowiedź przez lucpo 2012-11-15 23:42:55

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

24 Odpowiedź przez Cezary 2012-11-16 06:21:17

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

25 Odpowiedź przez lucpo 2012-11-16 15:47:17

Odp: Attitude Adjustment - extroot nie działa tak jak powinien

Posty: 1 do 25 z 50