1

Temat: Naprawa routera, pytanie o PuTTY

Podczas naprawy routera łączymy się przez SSH czy Telnet?
I łączymy się jak poprzez wpisanie numeru IP?

PuTTY skonfigurowałem w zakładce Serial.
Co dalej jak się połączyć?

2

Odp: Naprawa routera, pytanie o PuTTY

Ale jak, przez kabel szeregowy? To nie ssh czy telnet tylko serial port.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3

Odp: Naprawa routera, pytanie o PuTTY

Aha, czyli gdy jestem w zakładce Serial, tam ustawiłem Serial line to connect to COM8
to teraz wystarczy jak kliknę Open?

http://imageshack.us/a/img203/8862/bladwk.jpg

a o co chodzi, jeśli klikam Open i nic się nie dzieje?

4

Odp: Naprawa routera, pytanie o PuTTY

Hmm, a czemu tu? Na głównym ekranie masz to przecież:

https://lh4.googleusercontent.com/_DzseJg4jeV8/TcTsbRrGjAI/AAAAAAAAABU/KmKHGbcIcgQ/s800/putty.png

Serial kliknij i napisz który com i szybkość.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

5

Odp: Naprawa routera, pytanie o PuTTY

ahaa, to w ten sposób to zrobić trzeba...

no dobra, a co oznacza ten komunikat?
nie działa wpisywanie tpl, wo gule efekt jest taki jak by PuTTY klawiatury nie widział.

http://imageshack.us/a/img40/3954/bladrv.jpg

6

Odp: Naprawa routera, pytanie o PuTTY

Że Ci się system plików we flash posypał. Na tpl masz tylko sekundę i to w określonym miejscu. Próbuj.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

7

Odp: Naprawa routera, pytanie o PuTTY

z tym że w tym ciągu znaków nie ma Autobooting in 1 seconds

00650000)
[    9.350000] Node at 0x0065ff8c with length 0x000007fa would run over the end of the erase block
[    9.360000] Perhaps the file system was created with the wrong erase size?
[    9.370000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660000: 0x507e instead
[    9.380000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660004: 0xed75 instead
[    9.390000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660008: 0x3704 instead
[    9.400000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0066000c: 0xca25 instead
[    9.410000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660010: 0x8091 instead
[    9.410000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660014: 0x06f6 instead
[    9.420000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660018: 0x417e instead
t[    9.430000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0066001c: 0xa071 instead
[    9.440000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660020: 0x755e instead
[    9.450000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00660024: 0x40e8 instead
[    9.460000] Further such events for this erase block will not be printed
[    9.470000] CLEANMARKER node found at 0x00663000, not first node in block (0x00660000)
[    9.490000] Node at 0x0066fd50 with length 0x000005be would run over the end of the erase block
[    9.500000] Perhaps the file system was created with the wrong erase size?
[    9.510000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670000: 0xc279 instead
[    9.520000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670004: 0x3b51 instead
[    9.530000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670008: 0xe683 instead
[    9.540000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0067000c: 0x5ba7 instead
[    9.550000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670010: 0x86dc instead
p[    9.560000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670014: 0x429d instead
[    9.560000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670018: 0x8ca3 instead
[    9.570000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0067001c: 0x164b instead
[    9.580000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670020: 0x02a7 instead
[    9.590000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00670024: 0x6a82 instead
[    9.600000] Further such events for this erase block will not be printed
[    9.610000] CLEANMARKER node found at 0x00673000, not first node in block (0x00670000)
[    9.640000] Node at 0x0067f838 with length 0x000008d8 would run over the end of the erase block
[    9.640000] Perhaps the file system was created with the wrong erase size?
[    9.650000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680000: 0xdfbd instead
[    9.660000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680004: 0xb2b9 instead
l[    9.670000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680008: 0x52bd instead
[    9.680000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0068000c: 0x72b7 instead
[    9.690000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680010: 0x24dd instead
[    9.700000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680014: 0x3045 instead
[    9.710000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680018: 0x87d4 instead
[    9.710000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0068001c: 0x319d instead
[    9.720000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680020: 0x3f3a instead
[    9.730000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00680024: 0x2b23 instead
[    9.740000] Further such events for this erase block will not be printed
[    9.750000] CLEANMARKER node found at 0x00683000, not first node in block (0x00680000)
[    9.780000] Node at 0x0068ff60 with length 0x00000509 would run over the end of the erase block
[    9.790000] Perhaps the file system was created with the wrong erase size?
[    9.790000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690000: 0x3ff2 instead
[    9.800000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690004: 0x84f2 instead
[    9.810000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690008: 0x597c instead
[    9.820000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0069000c: 0x8c10 instead
[    9.830000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690010: 0x2311 instead

[    9.840000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690014: 0x0319 instead
[    9.850000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690018: 0x280a instead
[    9.860000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0069001c: 0x2651 instead
[    9.870000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690020: 0xf9f3 instead
[    9.870000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00690024: 0x6d92 instead
[    9.880000] Further such events for this erase block will not be printed
[    9.900000] CLEANMARKER node found at 0x00693000, not first node in block (0x00690000)
[    9.920000] Node at 0x0069fd68 with length 0x000006f8 would run over the end of the erase block
[    9.930000] Perhaps the file system was created with the wrong erase size?
[    9.940000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0000: 0xeae2 instead
[    9.950000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0004: 0x7cb4 instead
[    9.960000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0008: 0x745b instead
[    9.970000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a000c: 0xb278 instead
[    9.970000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0010: 0xcdbe instead
[    9.980000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0014: 0xecbf instead
[    9.990000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0018: 0x8c7d instead
[   10.000000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a001c: 0xc6c3 instead
[   10.010000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0020: 0x7019 instead
[   10.020000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006a0024: 0x1d34 instead
[   10.030000] Further such events for this erase block will not be printed
[   10.040000] CLEANMARKER node found at 0x006a3000, not first node in block (0x006a0000)
[   10.070000] Node at 0x006afe14 with length 0x0000055c would run over the end of the erase block
[   10.070000] Perhaps the file system was created with the wrong erase size?
[   10.080000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0000: 0x6f3f instead
[   10.090000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0004: 0xdc19 instead
[   10.100000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0008: 0x57bc instead
[   10.110000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b000c: 0xbb68 instead
[   10.120000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0010: 0x0cb7 instead
t[   10.130000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0014: 0xfba7 instead
[   10.130000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0018: 0xc9f3 instead
[   10.140000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b001c: 0xeb58 instead
[   10.150000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0020: 0xeab3 instead
[   10.160000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006b0024: 0x6ed0 instead
[   10.170000] Further such events for this erase block will not be printed
[   10.180000] CLEANMARKER node found at 0x006b3000, not first node in block (0x006b0000)
[   10.210000] Node at 0x006bfcb0 with length 0x00000914 would run over the end of the erase block
[   10.220000] Perhaps the file system was created with the wrong erase size?
[   10.220000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0000: 0x7b1d instead
[   10.230000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0004: 0xf322 instead
p[   10.240000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0008: 0x87d5 instead
[   10.250000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c000c: 0xa07a instead
[   10.260000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0010: 0x8c1d instead
[   10.270000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0014: 0x09c4 instead
[   10.280000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0018: 0xddaa instead
[   10.290000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c001c: 0xac82 instead
[   10.300000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0020: 0xf31a instead
[   10.300000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006c0024: 0x6849 instead
[   10.310000] Further such events for this erase block will not be printed
[   10.330000] CLEANMARKER node found at 0x006c3000, not first node in block (0x006c0000)
[   10.350000] Node at 0x006cff14 with length 0x00000473 would run over the end of the erase block
[   10.360000] Perhaps the file system was created with the wrong erase size?
l[   10.370000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0000: 0xbbbc instead
[   10.380000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0004: 0x2d21 instead
[   10.390000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0008: 0x4382 instead
[   10.390000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d000c: 0xf70e instead
[   10.400000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0010: 0x7dad instead
[   10.410000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0014: 0xb233 instead
[   10.420000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0018: 0xbba9 instead
[   10.430000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d001c: 0x1843 instead
[   10.440000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0020: 0xaeb2 instead
[   10.450000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x006d0024: 0xe66a instead
[   10.460000] Further such events for this erase block will not be printed
[   10.470000] Old JFFS2 bitmask found at 0x006d0360
[   10.470000] You cannot use older JFFS2 filesystems with newer kernels
[   10.480000] CLEANMARKER node found at 0x006d3000, not first node in block (0x006d0000)
[   10.510000] Node at 0x006dff04 with length 0x00000850 would run over the end of the erase block
[   10.520000] Perhaps the file system was created with the wrong erase size?

[   10.530000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 9 of xdatum (0 unchecked, 9 orphan) and 9 of xref (0 dead, 9 orphan) found.
[   10.540000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
[   10.550000] Freeing unused kernel memory: 212k freed
[   10.560000] Kernel panic - not syncing: No init found.  Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.

8

Odp: Naprawa routera, pytanie o PuTTY

Ale to co pokazałeś to jest o 9sek za późno już smile

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

9 (edytowany przez nigraS 2012-10-25 15:33:24)

Odp: Naprawa routera, pytanie o PuTTY

ok udało się, to teraz pytanie o firmware czy mogę od razu zainstalować Gargoyle?
ten?
http://ecco.selfip.net/gargoyle-pl/atti … actory.bin

10

Odp: Naprawa routera, pytanie o PuTTY

Nie, nie trzeba. Jest zaraz na starcie ten komunikat.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

11

Odp: Naprawa routera, pytanie o PuTTY

ile czasu trwa wgrywanie tftpboot 0x81000000 code.bin?
już z ponad 10 min czekam i w kółko wałkuje się ten sam komunikat.

http://imageshack.us/a/img841/106/bladve.jpg

Czy to normalne, mogę odpocząć i za jakiś czas firmware się wgra?

12

Odp: Naprawa routera, pytanie o PuTTY

Przecież Ty nic nie wgrywasz. Nie pobiera Ci pliku w komputera w ogóle. Postawiłeś tam serwer tftp?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

13 (edytowany przez sebastan 2012-10-25 16:09:38)

Odp: Naprawa routera, pytanie o PuTTY

Nic Ci się nie wgrywa, z tego co pamiętam u siebie nie masz łączności z serwerem ftp.  Musisz sprawdzić połączenia.

PS. Może chodzić o zakres IP ustawiony w karcie sieciowej. Oczywiście pod warunkiem, że w ogóle mamy serwer odpalony.

14

Odp: Naprawa routera, pytanie o PuTTY

tftp jest włączony, IP na karcie ustawione:
http://imageshack.us/a/img560/2428/bladme.jpg

15

Odp: Naprawa routera, pytanie o PuTTY

Ten serwer interface to źle masz, przeciez na 192.168.0.5 ma nasłuchiwać.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

16 (edytowany przez zdzichu6969 2012-10-25 16:34:25)

Odp: Naprawa routera, pytanie o PuTTY

Rozwin server interface i kliknij w IP 192.x.x.x

RB760iGS + RB260GS / Ryzen 5 2660 / 16G DDR4 / MiniITX - Inea 1G (https://i.imgur.com/TLbJVDw.png)
RB951-2HnD / Celeron J1900 / 4G DDR3 / MiniITX - Satpol 100M

17 (edytowany przez nigraS 2012-10-25 16:35:35)

Odp: Naprawa routera, pytanie o PuTTY

teraz serwer dobrze nasłuchuje, jednak w dalszym ciągu mam ten komunikat co był i co 10-te T od nowa liczy i tak w kółko.

18

Odp: Naprawa routera, pytanie o PuTTY

Dobrze działający serwer powiniem zassać Ci plik, co objawi się zarówno w oknie Tftpd (pokaże się wysyłanie) oraz w oknie putty. Jeśli się to nie dzieje to wciąż coś CI zakłóca komunikację. Zdarzają się np. zawzięte firewall'e.

19

Odp: Naprawa routera, pytanie o PuTTY

A to gdzie podłączam kabel RJ45 do routera to też jest istotne, czy nie ważne gdzie jest podłączony?

20

Odp: Naprawa routera, pytanie o PuTTY

Do portu lan. A gdzie to podłączyłeś?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

21

Odp: Naprawa routera, pytanie o PuTTY

do portu WAN.
ok teraz jest dobrze.

udało się naprawić.

było warto!

Dzięki WSZYSTKIM za pomoc.

22

Odp: Naprawa routera, pytanie o PuTTY

Witam. Dołączę się do tematu bo u mnie występuje podobna sytuacja ze nie mogę wpisywać nic z klawiatury w putt sad
http://img836.imageshack.us/img836/2368/beztytuufyk.jpg

Uploaded with ImageShack.us

Kabelek zakupilem taki http://allegro.pl/konwerter-usb-rs232-t … 18643.html

23

Odp: Naprawa routera, pytanie o PuTTY

A na pewno masz dobrze podłączone kabelki? RX z konwertera do TX na płycie routera oraz TX z konwertera do RX na płycie?

Gargoyle fanatic user
WR1043ND v2 16MB / WR902AC v3 / MR3020 16MB+64MB / WR703N / WT3020 / E3372

24

Odp: Naprawa routera, pytanie o PuTTY

mikhnal napisał/a:

A na pewno masz dobrze Ppodłączone kabelki? RX z konwertera do TX na płycie routera oraz TX z konwertera do RX na płycie?

Probowalem przemieniac je ale nic to nie dawalo (druga dioda swieci sie dopiero po podlaczeniu po ktorym laczy tak jak na obrazku do gory)

25

Odp: Naprawa routera, pytanie o PuTTY

Nic nie możesz wpisać bo musisz przerwać bootloader. Masz na to tylko 1s i to tylko w momencie jak wypisał "Autobooting..."

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.