Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Iomega iConnect jak przywrócić fabryczne firmware
Zaloguj się lub zarejestruj by napisać odpowiedź
Witam mam iconnecta z wgranym openwrt, w związku z tym ze prorobiłem router na 128mb nie potrzebuję już iomegi i pusciłbym ja na allegro, ale chchiałbym wgrac do niej oryginalne firmware, jak tego dokonać?? kabelek mam tylko czy musze jakoś spreparować fabryczny obraz no i co klepać w lini polecenia
iconnect ma swój tryb recovery. Sprawdź moje opisy, było jak jak go odzyskać.
BIG THX link dla ludzików z podobnym problemem http://openrouter.info/forum/viewtopic. … amp;t=1219
Cezary firmware wgrane, ale system nie startuje tylko ładuje się (miga dioda power) po czym na chwilke gaśnie dioda i od nowa próbuje ładować, co robić??
Tak jakby się resetował. Tu już serial potrzebujesz.
no serial mam ale jak wgrac firmware przez niego??
Na razie podłącz i zobacz co się dzieje. Jeżeli zawartość flash jest ok to tylko zmienne bootloadera musisz zmodyfikować.
Strzelam, że masz namieszane ze zmiennymi środowiskowymi - miałem tak samo, nic nie mogłem zrobić bo resetował się w pętli. Nawet jak wgrywałem oryginalne oprogramowanie to w kółko system restartował. Nie pomogło mi ustawianie zmiennych, tylko ich reset. W tym momencie nie pamiętam polecenia, ale wierzę, że ktoś podpowie.
No oczywiście do tego potrzebujesz seriala 
to wywala boot loader
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25
Mapower version: iConnect 2.1 (512MB) (2010/02/02)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................. done, booting the kernel.
Linux version 2.6.30.9 (soho@bsoho084.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 PREEMPT Mon Jan 25 13:57:26 EST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254848KB available (3632K code, 901K data, 124K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:b8:11:e3:67
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 478 at 0x000003bc0000
Bad eraseblock 978 at 0x000007a40000
Bad eraseblock 1822 at 0x00000e3c0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 509 MiB
UBI: number of good PEBs: 4069
UBI: number of bad PEBs: 3
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 71
UBI: total number of reserved PEBs: 3998
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 179153/153
UBI: background thread "ubi_bgt0d" started, PID 394
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2044-09-27 22:51:38 UTC (2358629498)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 1024 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 521216 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c002c834>] (unwind_backtrace+0x0/0xdc) from [<c02e493c>] (panic+0x48/0x12c)
[<c02e493c>] (panic+0x48/0x12c) from [<c0009050>] (mount_block_root+0x25c/0x2b4)
[<c0009050>] (mount_block_root+0x25c/0x2b4) from [<c00091a0>] (prepare_namespace+0x8c/0x1c8)
[<c00091a0>] (prepare_namespace+0x8c/0x1c8) from [<c00085ac>] (kernel_init+0xbc/0xec)
[<c00085ac>] (kernel_init+0xbc/0xec) from [<c003b730>] (do_exit+0x0/0x6e0)
[<c003b730>] (do_exit+0x0/0x6e0) from [<cf81a300>] (0xcf81a300)
Rebooting in 30 seconds..
root=ubi0:rootfs <--zostały Ci zmienne w uboocie z instalacji openwrt. Skasuj to.
Oryginalna tak wygląda:
console=ttyS0,115200 mtdparts=orion_nand:0xc0000@0x0(uboot), 0x20000@0xa0000(env), 0x300000@0x100000(zImage),
0x300000@0x540000(initrd),0x1f400000@0x980000(boot)
no jak mam to skasowac, jakie polecenia bo w uboocie nie kojarze nic
Przez setenv. Przecież tak ustawiałeś zmienne podczas instalacji openwrt, nie pamiętasz?
setenv root=ubi0:rootfs
saveenv
to wklepałem i dostałem
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25
Mapower version: iConnect 2.1 (512MB) (2010/02/02)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Marvell>> root=ubi0:rootfs
Unknown command 'root=ubi0:rootfs' - try 'help'
Marvell>> setenv console=ttyS0,115200 mtdparts=orion_nand:0xc0000@0x0(uboot), 0x20000@0xa0000(env), 0x300000@0x100000(zImage),
Marvell>> 0x300000@0x54000
Unknown command '0x300000@0x54000' - try 'help'
Marvell>> setenv ipaddr 192.168.1.1
Marvell>> setenv root=ubi0:rootfs
Marvell>> saveenv
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
Marvell>>
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25
Mapower version: iConnect 2.1 (512MB) (2010/02/02)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................. done, booting the kernel.
jak mniemam cos jest spierdolone
Weź przeczytaj dokładnie to co napisałem. Tam NIE MASZ rootfs. Masz w/w linię ustawić.
setenv console=ttyS0,115200 mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env), 0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)
saveenv
zrestartowałem i nadal kapa stioi w tym samym miejscu co co w poprzednim poście, moge sflashowac całego uboota wraz z firmware?? chyba bedzie dla mnie prościej
Inne Load Address i Entry point masz niż było u mnie. Znajdź kogoś kto ma oryginał i niech Ci da zawartość wszystkich zmiennych.
a jak taką zawartość wyekstraktować?
tu masz zawartość oryginalnych zmiennych: http://scriptkiller.de/en/a54/computer_ … _iconnect/
możesz sprawdzić jak masz u siebie.
Jakieś fw_printenv w oryginalnym sofcie powinno być.
a resetenv tu nie pomoże przypadkiem?
Nie mam pojęcia. Nie wiem ile resetenv czyści
u mnie też był taki problem - m.in. widziałem taki komunikat
[ 8.314519] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) (nie wiem czy to istotne, ale w logu wklejonym powyżej też się to pojawia), router sie restartował i pomogło właśnie resetenv - może warto spróbować...
Link do wątku http://openrouter.info/forum/viewtopic. … ;start=340
pzdr
Cześć, Mam ten sam problem: chciałem wrócić do ustawień fabrycznych. Szamotałem się z tym trochę. Nie pamietam co pozmieniałem. Teraz jak się bootuję dostaję. Jak mogę to naprawić? Dzięki z góry za wszelkie sugestie.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25
Mapower version: iConnect 2.1 (512MB) (2010/02/
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
Reading data from 0x3ff800 -- 100% complete.
3145728 bytes read: OK
NAND read: device 0 offset 0x540000, size 0x300000
Reading data from 0x83f800 -- 100% complete.
3145728 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 04500000 ...
Image Name:
Created: 2010-03-05 2:28:47 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1774143 Bytes = 1.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux.............................................................
.................................................................... done, booti
ng the kernel.
Linux version 2.6.30.9 (soho@bsoho084.lss.emc.com) (gcc version 4.3.2 (crosstool
-NG-1.3.1) ) #1 PREEMPT Mon Jan 25 13:57:26 EST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0x0(uboot),0
x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),128m@0x0
(flash)
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 253056KB available (3632K code, 901K data, 124K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usb
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 1732K
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:50:43:66:1b:20
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1223 at 0x0000098e0000
Bad eraseblock 2830 at 0x0000161c0000
Bad eraseblock 2883 at 0x000016860000
Bad eraseblock 2885 at 0x0000168a0000
Bad eraseblock 2886 at 0x0000168c0000
Bad eraseblock 2887 at 0x0000168e
Bad eraseblock 2889 at 0x000016920000
Bad eraseblock 2891 at 0x000016960000
Bad eraseblock 2893 at 0x0000169a0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "root"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2014-06-12 22:42:34 UTC (1402612954)
RAMDISK: gzip image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
usb 1-1: new high speed USB device using orion-ehci and address 2
USB Device node is /dev/sda1
Checking if there is an attached EMC Imager
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports dete
mount: mounting /dev/sda1 on /usb_drive failed: No such device or address
ubiattach: error!: cannot attachUBIFS error (pid 478): ubifs_get_sb: cannot open
"ubi0:boot", error -19
mtd4
error 19 (No such device)
mount: mounting ubi0:boot on sysroot/boot failed: No such device
umount: cannot umount sysroot/boot: Invalid argument
/mount_images.sh: line 62: do_network_imaging: not found
Constructing root filesystem...
cp: cannot stat '/sysroot/mnt/apps/ram': No such file or directory
/linuxrc: line 54: echo: not found
/linuxrc: line 55: /usr/local/cfg/initrd_bootstrap.sh: not found
/linuxrc: line 57: ln: not found
/linuxrc: line 59: mount: not found
/linuxrc: line 61: echo: not found
Freeing init memory: 124K
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
[<c002c834>] (unwind_backtrace+0x0/0xdc) from [<c02e493c>] (panic+0x48/0x12c)
[<c02e493c>] (panic+0x48/0x12c) from [<c00275ac>] (init_post+0x13c/0x174)
[<c00275ac>] (init_post+0x13c/0x174) from [<c00085b0>] (kernel_init+0xc0/0xec)
[<c00085b0>] (kernel_init+0xc0/0xec) from [<c003b730>] (do_exit+0x0/0x6e0)
[<c003b730>] (do_exit+0x0/0x6e0) from [<cf81a300>] (0xcf81a300)Pewnie coś ze zmiennych uboota przestawiłeś
NO tak w końcu zrobiłem resetenv i po tym mam właśnie 'Kernel panic - not syncing'.
Sprobuje wrzucić zmienne ze stronki
http://scriptkiller.de/en/a54/computer_ … _iconnect/
Tam na dole strony są podobno oryginalne zmienne.
Załątwiłem się z tym 'resetenv'...
Mam wyczyszczone Mac adresy kart.
Na stronce ze zrzutem zmiennych (dół strony www)
http://scriptkiller.de/en/a54/computer_ … _iconnect/
jest parę lini z adresami MAC:
eth1addr=00:50:43:5a:1a:2d
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
yuk_ethaddr=00:00:00:EE:51:81
ethaddr=00:D0:B8:0D:0E:C7Z kolei ze zdjęć wynika, żę Iomega ma adresy dla
WIFI = 00:D0:B8:0D:0E:C7
LAN = 00:DE:8E:29:39:A9
Wygląda więc że tylko adresy wifi zą zgodne. A LAN? O co tu chodzi....?
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Iomega iConnect jak przywrócić fabryczne firmware
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc