1 Temat przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Temat: 1.14 extroot i problem

Właśnie wgrałem sobie wersje 1.14 i nie przyszło mi do głowy, że trzeba robić extroota od nowa. Stanąłem w punkcie wykrywania dysku usb. Z poradnika https://eko.one.pl/forum/viewtopic.php?id=1062
Albo ślepnę albo nie widzi dysku, może ktoś sprawdzić czy widać tam dwie partycje ? Jedna to stara ext2  z 1.13 a druga to ntfs.

root@Gargoyle:~# dmesg
[    0.000000] Linux version 5.10.176 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Thu Apr 27 20:28:15 2023
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is TP-Link TL-WR1043ND v3
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 57088K/65536K available (5145K kernel code, 581K rwdata, 692K rodata, 1188K init, 195K bss, 8448K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 720.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000008] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008351] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.075035] pid_max: default: 32768 minimum: 301
[    0.080075] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.087852] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.097705] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.108070] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.118576] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.125850] pinctrl core: initialized pinctrl subsystem
[    0.132784] NET: Registered protocol family 16
[    0.183443] clocksource: Switched to clocksource MIPS
[    0.189880] NET: Registered protocol family 2
[    0.194824] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.203089] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.212061] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.220236] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.227759] TCP: Hash tables configured (established 1024 bind 1024)
[    0.234656] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.241627] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.249339] NET: Registered protocol family 1
[    0.254042] PCI: CLS 0 bytes, default 32
[    0.263355] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.273106] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.279370] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.293197] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[    0.299840] gpio-export gpio-export: 1 gpio(s) exported
[    0.306260] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.313698] printk: console [ttyS0] disabled
[    0.318309] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.327530] printk: console [ttyS0] enabled
[    0.336435] printk: bootconsole [early0] disabled
[    0.356491] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[    0.361502] 3 fixed-partitions partitions found on MTD device spi0.0
[    0.368041] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.374784] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.382283] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.389065] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[    0.396035] Creating 3 MTD partitions on "spi0.0":
[    0.400906] 0x000000000000-0x000000020000 : "u-boot"
[    0.410390] 0x000000020000-0x0000007f0000 : "firmware"
[    0.416897] 2 tplink-fw partitions found on MTD device firmware
[    0.422912] Creating 2 MTD partitions on "firmware":
[    0.428006] 0x000000000000-0x0000001ea3de : "kernel"
[    0.433036] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[    0.443573] 0x0000001ea3e0-0x0000007d0000 : "rootfs"
[    0.448623] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[    0.458807] mtd: setting mtd3 (rootfs) as root device
[    0.464727] 1 squashfs-split partitions found on MTD device rootfs
[    0.471010] 0x000000650000-0x0000007d0000 : "rootfs_data"
[    0.477349] 0x0000007f0000-0x000000800000 : "art"
[    0.858683] switch0: Atheros AR8327 rev. 4 switch registered on mdio.0
[    1.512812] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    1.523917] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    1.865433] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[    1.875103] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[    1.881812] i2c /dev entries driver
[    1.887386] NET: Registered protocol family 10
[    1.899360] Segment Routing with IPv6
[    1.903188] NET: Registered protocol family 17
[    1.907800] 8021q: 802.1Q VLAN Support v1.8
[    1.923725] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.937306] Freeing unused kernel memory: 1188K
[    1.941902] This architecture does not have kernel memory protection.
[    1.948467] Run /sbin/init as init process
[    1.952618]   with arguments:
[    1.952622]     /sbin/init
[    1.952626]   with environment:
[    1.952630]     HOME=/
[    1.952633]     TERM=linux
[    3.722309] init: Console is alive
[    3.726272] init: - watchdog -
[    6.128508] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.638265] usbcore: registered new interface driver usbfs
[    6.643967] usbcore: registered new interface driver hub
[    6.649438] usbcore: registered new device driver usb
[    6.669409] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.678457] fsl-ehci: Freescale EHCI Host controller driver
[    6.685968] ehci-platform: EHCI generic platform driver
[    6.691647] ehci-platform 1b000000.usb: EHCI Host Controller
[    6.697472] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[    6.705545] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[    6.733467] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    6.740522] hub 1-0:1.0: USB hub found
[    6.745084] hub 1-0:1.0: 1 port detected
[    6.752864] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.770679] init: - preinit -
[    7.232247] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    9.262150] random: jshn: uninitialized urandom read (4 bytes read)
[    9.414849] random: jshn: uninitialized urandom read (4 bytes read)
[    9.570748] random: jshn: uninitialized urandom read (4 bytes read)
[   12.413999] eth1: link up (1000Mbps/Full duplex)
[   12.423554] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   12.430287] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
[   12.517900] random: procd: uninitialized urandom read (4 bytes read)
[   17.560226] jffs2: notice: (494) jffs2_build_xattr_subsystem: complete building xattr subsystem, 30 of xdatum (26 unchecked, 4 orphan) and 38 of xref (4 dead, 0 orphan) found.
[   17.589841] mount_root: loading kmods from internal overlay
[   17.655698] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   17.667304] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[   17.930134] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   17.942430] block: extroot: not configured
[   17.947710] mount_root: switching to jffs2 overlay
[   17.960946] overlayfs: upper fs does not support tmpfile.
[   17.972834] urandom-seed: Seeding with /etc/urandom.seed
[   18.017827] eth1: link down
[   18.042246] procd: - early -
[   18.045558] procd: - watchdog -
[   18.640001] procd: - watchdog -
[   18.647842] procd: - ubus -
[   19.257671] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.273045] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.306636] random: ubusd: uninitialized urandom read (4 bytes read)
[   19.323675] procd: - init -
[   21.013022] random: jshn: uninitialized urandom read (4 bytes read)
[   21.043763] random: ubusd: uninitialized urandom read (4 bytes read)
[   21.057266] random: ubus: uninitialized urandom read (4 bytes read)
[   21.820745] kmodloader: loading kernel modules from /etc/modules.d/*
[   22.111538] urngd: v1.0.2 started.
[   22.270734] random: crng init done
[   22.274243] random: 24 urandom warning(s) missed due to ratelimiting
[   22.298796] tun: Universal TUN/TAP device driver, 1.6
[   22.423019] GACT probability on
[   22.428965] Mirror/redirect action on
[   22.448174] u32 classifier
[   22.450936]     input device check on
[   22.454691]     Actions configured
[   22.480307] Simple TC action Loaded
[   22.546229] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f
[   22.553967] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c
[   22.892128] xt_time: kernel timezone is -0000
[   22.998413] PPP generic driver version 2.4.2
[   23.007533] NET: Registered protocol family 24
[   23.018464] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   23.026476] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[   23.101467] ath: EEPROM regdomain: 0x0
[   23.101479] ath: EEPROM indicates default country code should be used
[   23.101484] ath: doing EEPROM country->regdmn map search
[   23.101498] ath: country maps to regdmn code: 0x3a
[   23.101505] ath: Country alpha2 being used: US
[   23.101509] ath: Regpair used: 0x3a
[   23.119382] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   23.121282] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=12
[   23.174055] kmodloader: done loading kernel modules from /etc/modules.d/*
[   44.300430] eth1: link up (1000Mbps/Full duplex)
[   44.316687] br-lan: port 1(eth1.1) entered blocking state
[   44.322177] br-lan: port 1(eth1.1) entered disabled state
[   44.327978] device eth1.1 entered promiscuous mode
[   44.332847] device eth1 entered promiscuous mode
[   44.341213] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   44.373936] br-lan: port 1(eth1.1) entered blocking state
[   44.379431] br-lan: port 1(eth1.1) entered forwarding state
[   44.482936] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is up
[   44.489223] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 4 is up
[   44.495467] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is up
[   44.502962] eth0: link up (1000Mbps/Full duplex)
[   44.543762] device eth0 entered promiscuous mode
[   44.643530] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   45.373788] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   50.349133] br-lan: port 2(wlan0) entered blocking state
[   50.354579] br-lan: port 2(wlan0) entered disabled state
[   50.360387] device wlan0 entered promiscuous mode
[   50.479373] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   50.486067] br-lan: port 2(wlan0) entered blocking state
[   50.491467] br-lan: port 2(wlan0) entered forwarding state
[   93.868593] xt_bandwidth: timezone shift of 60 minutes detected, adjusting
[   93.875640]                old minutes west=0, new minutes west=-60

2 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

I jeszcze to przy dalszych krokach poradnika:


root@Gargoyle:~# uci set fstab.automount.anon_mount=1
uci: Invalid argument

3 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Po co chcesz to robisz jak gargoyle samodzielnie montuje nośniki wykorzystując własne mechanizmy?

nie, nie widzi ci nośnika.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

4 Odpowiedź przez lebexx (edytowany przez lebexx 2023-12-21 18:55:43)

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Nie mogę nic doinstalować z poziomu www bo brakuje miejsca. I teraz nie wiem jak zrobić extroota sad(
A teraz ?

[  610.568567] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 4 is down
[  864.316860] usb 1-1: USB disconnect, device number 2
[  970.273423] usb 1-1: new high-speed USB device number 3 using ehci-platform
[  980.513260] usb 1-1: USB disconnect, device number 3
[ 1015.522828] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 1032.998972] usb 1-1: USB disconnect, device number 4
[ 1035.852588] usb 1-1: new high-speed USB device number 5 using ehci-platform

5 Odpowiedź przez lebexx (edytowany przez lebexx 2023-12-21 19:23:38)

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Nie rozumiem jak to jest, że 1.14 zaraz po instalacji nie widzi dysku usb. O co tu chodzi ?
W ogóle to nawet dysk się nie zaczyna kręcić po podłączeniu do usb. Wygląda, że to usb jest jakoś całkowicie wyłączone.

6 Odpowiedź przez Focus

  • Focus
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2020-10-20
  • Posty: 972

Odp: 1.14 extroot i problem

A próbowałeś podłączyć ten dysk przez aktywny hub?
Jeden ze znanych od dawna problemów to brak odpowiedniego zasilania USB.

7 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Przecież na 1.13 działał normalnie. Teraz wgrałem od nowa 1.14 i dalej po podłączeniu dysk się nie kręci nawet. Jakaś lipa to 1.14, nie pozostaje mi nic innego jak wgrać z powrotem 1.13 i użyć kopii konfiga zamiast się tu męczyć do rana.

8 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

I co mam se zrobić ? Skoro takie kwiatki wychodzą, dupa z tym extrootem na 1.14 i tyle :[


root@Gargoyle:~# opkg install block-hotplug
ERROR: No package named block-hotplug found, try updating your package lists

9 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Używasz gargoyle. Przestań w końcu robić to jak w zwykłym openwrt bo tylko namieszasz w systemie. Pisałem już, gargoyle używa własnych mechanizmów do montowania. Nie ma ogóle takiego pakietu jak block-hotplug więc nie zmyślaj pierwszych lepszych nazw.

Obrazy dla 1043v2 nie zawierają w ogóle kmod-usb-storage, z powodu wielkości flash (tam jest tylko 8MB a 1.14 jest sporo więckszy). Jeżeli masz miejsce to sobie doinstaluj to najpierw, tak samo jak pliki od obsługi danego systemu plików.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

10 Odpowiedź przez lebexx (edytowany przez lebexx 2023-12-21 20:42:18)

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Ja robię tylko to co  jest napisane w poradniku. Co mam doinstalować, żeby widział usb ?

11 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

W którym poradniku masz napisane o pakiecie block-hotplug?

opkg update
opkg install block-mount kmod-fs-ext4 kmod-usb-storage

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

12 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Z tego robię: https://eko.one.pl/forum/viewtopic.php?id=1062

13 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Przecież to jest poradnik napisany przez kogoś 13 lat temu. Naprawdę pomyślałeś że przez te 13lat nic się nie zmieniło?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

14 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

O teraz poszło. Tak po krótce, żeby teraz wgrać extroota 1.14 w miejsce 1.13 na dysk to jak to zrobić ?

15 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Nic z 1.13 nie podłączaj do 1.14. Nie ta wersja systemu. Robisz wszystko od początku.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

16 Odpowiedź przez lebexx (edytowany przez lebexx 2023-12-21 21:58:48)

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Wiem, czyli zaczynam teraz od punktu z fdisk ?
Pendrive zadziałał, dysk niestety dalej nie kręci, coś jeszcze trzeba dołożyć.

17 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Może kmod-usb-strorage-uas może coś zalezy. Zależy od tego dysku.

Tak, lecisz od formatowania itd.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

18 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Stanąłem na formatowaniu, nie mam polecenia mkfs.ext4, 3 albo 2. Jak to doinstalować ?

19 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Musisz mieć w systemie zainstalowany pakiet e2fsprogs

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

20 Odpowiedź przez lebexx (edytowany przez lebexx 2023-12-22 11:14:26)

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Kurde chyba coś namieszałem:
ERROR: Specified install destination is not writable, exiting

Brak miejsca ? Da się to zainstalować na zrobionych już partycjach pod extroota ?

21 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Zamontowałeś tylko do odczytu lub masz błędy w systemie plików i samo się tak zamontowało.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

22 Odpowiedź przez lebexx (edytowany przez lebexx 2023-12-22 15:38:57)

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Możesz mi podać proszę zawartość /etc/config/fstab
Mam już porobione, ale po reboocie nie montuje mi sda1 i sda2 jako swap.

W logach  jest  block: extroot: cannot find device with UUID 3780ad4b-6db4-4707-aae0-1508c6e44404
UUID jest prawidłowe, wzięte z blkid, więc o co mu chodzi ?

Dałem jeszcze opóźnienie 15 i teraz jest jeszcze
block: extroot: filesystem ext4 not supported by kernel

log z uruchamiania

Fri Dec 22 14:01:17 2023 kern.notice kernel: [   17.930385] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
Fri Dec 22 14:01:17 2023 kern.notice kernel: [   17.938213] sd 0:0:0:0: [sda] 4096-byte physical blocks
Fri Dec 22 14:01:17 2023 kern.notice kernel: [   17.954904] sd 0:0:0:0: [sda] Write Protect is off
Fri Dec 22 14:01:17 2023 kern.debug kernel: [   17.959807] sd 0:0:0:0: [sda] Mode Sense: 5f 00 00 08
Fri Dec 22 14:01:17 2023 kern.notice kernel: [   17.967052] sd 0:0:0:0: [sda] Disabling FUA
Fri Dec 22 14:01:17 2023 kern.notice kernel: [   17.971313] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Fri Dec 22 14:01:17 2023 kern.warn kernel: [   17.993675] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
Fri Dec 22 14:01:17 2023 kern.info kernel: [   18.391692]  sda: sda1 sda2 sda3
Fri Dec 22 14:01:17 2023 user.info kernel: [   18.405844] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Fri Dec 22 14:01:17 2023 kern.notice kernel: [   18.413386] sd 0:0:0:0: [sda] Attached SCSI disk
Fri Dec 22 14:01:17 2023 user.info kernel: [   18.422043] block: extroot: device not present, retrying in 15 seconds
Fri Dec 22 14:01:17 2023 user.err kernel: [   33.956223] block: extroot: filesystem ext4 not supported by kernel
Fri Dec 22 14:01:17 2023 user.info kernel: [   33.963843] mount_root: switching to jffs2 overlay
Fri Dec 22 14:01:17 2023 kern.warn kernel: [   33.975656] overlayfs: upper fs does not support tmpfile.

Może ktoś chętny zrobić mi to zdalnie za czteropaka ?

23 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

Tu masz: https://eko.one.pl/?p=openwrt-hdd#barri … szewydania

Co oczywiście z żaden sposób ci nie pomaga bo pytanie o zawartość fstaba była taka sobie.

Usuń wszystkie opóźnienia, zrestartuj i pokaż cały wynik logread od samego startu routera.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

24 Odpowiedź przez lebexx

  • lebexx
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2022-12-01
  • Posty: 117

Odp: 1.14 extroot i problem

Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.000000] Linux version 5.10.176 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 Thu Apr 27 20:28:15 2023
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] printk: bootconsole [early0] enabled
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] MIPS: machine is TP-Link TL-WR1043ND v3
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Initrd not found or empty - disabling initrd
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Zone ranges:
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Movable zone start for each node
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Early memory node ranges
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    0.000000] On node 0 totalpages: 16384
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    0.000000]   Normal zone: 128 pages used for memmap
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    0.000000]   Normal zone: 16384 pages, LIFO batch:3
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] Memory: 57088K/65536K available (5145K kernel code, 581K rwdata, 692K rodata, 1188K init, 195K bss, 8448K reserved, 0K cma-reserved)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] NR_IRQS: 51
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] CPU clock: 720.000 MHz
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.000008] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.008350] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.075035] pid_max: default: 32768 minimum: 301
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.080075] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.087851] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.097707] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.108067] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.118567] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.125842] pinctrl core: initialized pinctrl subsystem
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.132774] NET: Registered protocol family 16
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.183412] clocksource: Switched to clocksource MIPS
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.189850] NET: Registered protocol family 2
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.194792] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.203054] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.212028] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.220202] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.227726] TCP: Hash tables configured (established 1024 bind 1024)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.234623] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.241593] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.249305] NET: Registered protocol family 1
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.254008] PCI: CLS 0 bytes, default 32
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.263322] workingset: timestamp_bits=30 max_order=14 bucket_order=0
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.273070] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.279328] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.293155] pinctrl-single 1804002c.pinmux: 544 pins, size 68
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.299798] gpio-export gpio-export: 1 gpio(s) exported
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.306220] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.313663] printk: console [ttyS0] disabled
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.318275] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.327495] printk: console [ttyS0] enabled
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.336402] printk: bootconsole [early0] disabled
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.356458] spi-nor spi0.0: s25fl064k (8192 Kbytes)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.361469] 3 fixed-partitions partitions found on MTD device spi0.0
Fri Dec 22 15:14:37 2023 kern.err kernel: [    0.368008] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Fri Dec 22 15:14:37 2023 kern.err kernel: [    0.374749] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Fri Dec 22 15:14:37 2023 kern.err kernel: [    0.382241] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Fri Dec 22 15:14:37 2023 kern.err kernel: [    0.389022] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.395991] Creating 3 MTD partitions on "spi0.0":
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.400863] 0x000000000000-0x000000020000 : "u-boot"
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.410355] 0x000000020000-0x0000007f0000 : "firmware"
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.416863] 2 tplink-fw partitions found on MTD device firmware
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.422878] Creating 2 MTD partitions on "firmware":
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.427972] 0x000000000000-0x0000001ea3de : "kernel"
Fri Dec 22 15:14:37 2023 kern.warn kernel: [    0.433003] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.443537] 0x0000001ea3e0-0x0000007d0000 : "rootfs"
Fri Dec 22 15:14:37 2023 kern.warn kernel: [    0.448581] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.458761] mtd: setting mtd3 (rootfs) as root device
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.464675] 1 squashfs-split partitions found on MTD device rootfs
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.470959] 0x000000650000-0x0000007d0000 : "rootfs_data"
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    0.477298] 0x0000007f0000-0x000000800000 : "art"
Fri Dec 22 15:14:37 2023 kern.info kernel: [    0.858649] switch0: Atheros AR8327 rev. 4 switch registered on mdio.0
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.512782] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.523889] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.865400] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.875070] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.881786] i2c /dev entries driver
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.887355] NET: Registered protocol family 10
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.899349] Segment Routing with IPv6
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.903183] NET: Registered protocol family 17
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.907794] 8021q: 802.1Q VLAN Support v1.8
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.923730] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.937298] Freeing unused kernel memory: 1188K
Fri Dec 22 15:14:37 2023 kern.warn kernel: [    1.941894] This architecture does not have kernel memory protection.
Fri Dec 22 15:14:37 2023 kern.info kernel: [    1.948460] Run /sbin/init as init process
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    1.952611]   with arguments:
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    1.952615]     /sbin/init
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    1.952618]   with environment:
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    1.952622]     HOME=/
Fri Dec 22 15:14:37 2023 kern.debug kernel: [    1.952626]     TERM=linux
Fri Dec 22 15:14:37 2023 user.info kernel: [    3.722030] init: Console is alive
Fri Dec 22 15:14:37 2023 user.info kernel: [    3.725987] init: - watchdog -
Fri Dec 22 15:14:37 2023 user.info kernel: [    6.127824] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.637297] usbcore: registered new interface driver usbfs
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.642927] usbcore: registered new interface driver hub
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.648450] usbcore: registered new device driver usb
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.668555] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.677059] fsl-ehci: Freescale EHCI Host controller driver
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.685160] ehci-platform: EHCI generic platform driver
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.690840] ehci-platform 1b000000.usb: EHCI Host Controller
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.696663] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.704738] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.733435] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.740492] hub 1-0:1.0: USB hub found
Fri Dec 22 15:14:37 2023 kern.info kernel: [    6.745041] hub 1-0:1.0: 1 port detected
Fri Dec 22 15:14:37 2023 user.info kernel: [    6.752831] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Fri Dec 22 15:14:37 2023 user.info kernel: [    6.770640] init: - preinit -
Fri Dec 22 15:14:37 2023 kern.info kernel: [    7.232208] usb 1-1: new high-speed USB device number 2 using ehci-platform
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    9.262812] random: jshn: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    9.416594] random: jshn: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [    9.572001] random: jshn: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.info kernel: [   12.413704] eth1: link up (1000Mbps/Full duplex)
Fri Dec 22 15:14:37 2023 kern.info kernel: [   12.423514] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Fri Dec 22 15:14:37 2023 kern.info kernel: [   12.430248] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   12.517509] random: procd: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.549842] jffs2: notice: (494) jffs2_build_xattr_subsystem: complete building xattr subsystem, 40 of xdatum (33 unchecked, 7 orphan) and 56 of xref (10 dead, 0 orphan) found.
Fri Dec 22 15:14:37 2023 user.info kernel: [   17.578454] mount_root: loading kmods from internal overlay
Fri Dec 22 15:14:37 2023 user.info kernel: [   17.734612] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.814097] SCSI subsystem initialized
Fri Dec 22 15:14:37 2023 kern.info kernel: [   17.868766] usbcore: registered new interface driver usb-storage
Fri Dec 22 15:14:37 2023 kern.info kernel: [   17.882442] scsi host0: uas
Fri Dec 22 15:14:37 2023 kern.info kernel: [   17.886207] usbcore: registered new interface driver uas
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.893614] scsi 0:0:0:0: Direct-Access     JMicron  Generic          0209 PQ: 0 ANSI: 6
Fri Dec 22 15:14:37 2023 user.info kernel: [   17.902328] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.917343] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.925185] sd 0:0:0:0: [sda] 4096-byte physical blocks
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.937443] sd 0:0:0:0: [sda] Write Protect is off
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   17.942368] sd 0:0:0:0: [sda] Mode Sense: 5f 00 00 08
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.948245] sd 0:0:0:0: [sda] Disabling FUA
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   17.952527] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Fri Dec 22 15:14:37 2023 kern.warn kernel: [   17.974866] sd 0:0:0:0: [sda] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
Fri Dec 22 15:14:37 2023 kern.info kernel: [   18.031488]  sda: sda1 sda2 sda3
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   18.042127] sd 0:0:0:0: [sda] Attached SCSI disk
Fri Dec 22 15:14:37 2023 user.info kernel: [   18.244583] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Fri Dec 22 15:14:37 2023 user.err kernel: [   18.255395] block: extroot: cannot find device with UUID 3780ad4b-6db4-4707-aae0-1508c6e44404
Fri Dec 22 15:14:37 2023 user.info kernel: [   18.265270] mount_root: switching to jffs2 overlay
Fri Dec 22 15:14:37 2023 kern.warn kernel: [   18.277813] overlayfs: upper fs does not support tmpfile.
Fri Dec 22 15:14:37 2023 user.warn kernel: [   18.289849] urandom-seed: Seeding with /etc/urandom.seed
Fri Dec 22 15:14:37 2023 kern.info kernel: [   18.333645] eth1: link down
Fri Dec 22 15:14:37 2023 user.info kernel: [   18.358570] procd: - early -
Fri Dec 22 15:14:37 2023 user.info kernel: [   18.361805] procd: - watchdog -
Fri Dec 22 15:14:37 2023 user.info kernel: [   18.967913] procd: - watchdog -
Fri Dec 22 15:14:37 2023 user.info kernel: [   18.975590] procd: - ubus -
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   19.441196] random: ubusd: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   19.450859] random: ubusd: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   19.458358] random: ubusd: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 user.info kernel: [   19.471252] procd: - init -
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   21.019194] random: jshn: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   21.051476] random: ubusd: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   21.062544] random: ubus: uninitialized urandom read (4 bytes read)
Fri Dec 22 15:14:37 2023 user.info kernel: [   21.942434] kmodloader: loading kernel modules from /etc/modules.d/*
Fri Dec 22 15:14:37 2023 user.info kernel: [   22.261135] urngd: v1.0.2 started.
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   22.530706] random: crng init done
Fri Dec 22 15:14:37 2023 kern.notice kernel: [   22.534227] random: 23 urandom warning(s) missed due to ratelimiting
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.606512] tun: Universal TUN/TAP device driver, 1.6
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.810117] GACT probability on
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.820505] Mirror/redirect action on
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.853086] u32 classifier
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.855901]     input device check on
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.859615]     Actions configured
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.911129] Simple TC action Loaded
Fri Dec 22 15:14:37 2023 kern.info kernel: [   22.998261] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.005998] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.440307] xt_time: kernel timezone is -0000
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.630529] PPP generic driver version 2.4.2
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.647500] NET: Registered protocol family 24
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.668814] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.676823] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.809440] ath: EEPROM regdomain: 0x0
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.809452] ath: EEPROM indicates default country code should be used
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.809457] ath: doing EEPROM country->regdmn map search
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.809471] ath: country maps to regdmn code: 0x3a
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.809478] ath: Country alpha2 being used: US
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.809482] ath: Regpair used: 0x3a
Fri Dec 22 15:14:37 2023 kern.debug kernel: [   23.827243] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Fri Dec 22 15:14:37 2023 kern.info kernel: [   23.829155] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=12
Fri Dec 22 15:14:37 2023 user.info kernel: [   23.877837] kmodloader: done loading kernel modules from /etc/modules.d/*
Fri Dec 22 15:14:37 2023 daemon.notice procd: /etc/rc.d/S13openssl: Generating engines.cnf
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .bit
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .glue
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .parody
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .dyn
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .bbs
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .free
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .fur
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .geek
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .gopher
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .indy
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .ing
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .null
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .oss
Fri Dec 22 15:14:39 2023 user.notice dnsmasq: Allowing RFC1918 responses for domain .micro
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: started, version 2.86 cachesize 150
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: DNS service limited to local subnets
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: UBus support enabled: connected to system bus
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 178.32.31.41#53 for domain bit
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 176.58.118.172#53 for domain bit
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain glue
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain glue
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain glue
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain parody
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain parody
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain parody
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain dyn
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain dyn
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain dyn
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain bbs
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain bbs
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain bbs
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain free
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain free
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain free
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain fur
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain fur
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain fur
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain geek
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain geek
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain geek
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain gopher
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain gopher
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain gopher
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain indy
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain indy
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain indy
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain ing
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for test
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for onion
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for localhost
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for local
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for invalid
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for bind
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for lan
Fri Dec 22 15:14:41 2023 daemon.warn dnsmasq[1243]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: read /etc/hosts - 5 addresses
Fri Dec 22 15:14:41 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Fri Dec 22 15:14:41 2023 authpriv.info dropbear[1307]: Not backgrounding
Fri Dec 22 15:14:52 2023 daemon.notice wpa_supplicant[1515]: Successfully initialized wpa_supplicant
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: bonding
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: 8021ad
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: 8021q
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: macvlan
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: veth
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: bridge
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: Network device
Fri Dec 22 15:14:54 2023 user.notice : Added device handler type: tunnel
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.228225] eth1: link up (1000Mbps/Full duplex)
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.232935] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.256660] br-lan: port 1(eth1.1) entered blocking state
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.262145] br-lan: port 1(eth1.1) entered disabled state
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.268052] device eth1.1 entered promiscuous mode
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.272921] device eth1 entered promiscuous mode
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.300216] br-lan: port 1(eth1.1) entered blocking state
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.305750] br-lan: port 1(eth1.1) entered forwarding state
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'lan' is enabled
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'lan' is setting up now
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'lan' is now up
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: reading /tmp/resolv.conf.d/resolv.conf.auto
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 178.32.31.41#53 for domain bit
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 176.58.118.172#53 for domain bit
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain glue
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain glue
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain glue
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain parody
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain parody
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain parody
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain dyn
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain dyn
Fri Dec 22 15:14:59 2023 daemon.notice netifd: bridge 'br-lan' link is up
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'lan' has link connectivity
Fri Dec 22 15:14:59 2023 daemon.notice netifd: VLAN 'eth1.1' link is up
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain dyn
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain bbs
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain bbs
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain bbs
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain free
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain free
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain free
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain fur
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain fur
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain fur
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain geek
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain geek
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain geek
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'loopback' is enabled
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'loopback' is setting up now
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain gopher
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain gopher
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain gopher
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain indy
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'loopback' is now up
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.411595] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 3 is up
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.418016] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 5 is up
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.425525] eth0: link up (1000Mbps/Full duplex)
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain indy
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain indy
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain ing
Fri Dec 22 15:14:59 2023 daemon.warn dnsmasq[1243]: ignoring nameserver 192.168.1.1 - local interface
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for test
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for onion
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for localhost
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for local
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for invalid
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for bind
Fri Dec 22 15:14:59 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for lan
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.459028] device eth0 entered promiscuous mode
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan' is enabled
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan6' is enabled
Fri Dec 22 15:14:59 2023 kern.info kernel: [   49.477144] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Network device 'eth1' link is up
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Network device 'lo' link is up
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'loopback' has link connectivity
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Network device 'eth0' link is up
Fri Dec 22 15:14:59 2023 daemon.notice netifd: VLAN 'eth0.2' link is up
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan' has link connectivity
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan' is setting up now
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan6' has link connectivity
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan6' is setting up now
Fri Dec 22 15:14:59 2023 daemon.notice netifd: Interface 'wan6' is now up
Fri Dec 22 15:15:00 2023 kern.info kernel: [   50.253499] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Fri Dec 22 15:15:00 2023 daemon.notice netifd: wan (1800): udhcpc: started, v1.35.0
Fri Dec 22 15:15:00 2023 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Fri Dec 22 15:15:00 2023 daemon.err odhcpd[1645]: Failed to send to ff02::1%lan@br-lan (Address not available)
Fri Dec 22 15:15:00 2023 daemon.notice netifd: wan (1800): udhcpc: broadcasting discover
Fri Dec 22 15:15:00 2023 daemon.notice netifd: wan (1800): udhcpc: broadcasting select for 10.100.9.110, server 10.100.0.1
Fri Dec 22 15:15:01 2023 daemon.notice netifd: wan (1800): udhcpc: lease of 10.100.9.110 obtained from 10.100.0.1, lease time 86400
Fri Dec 22 15:15:01 2023 daemon.notice netifd: Interface 'wan' is now up
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: reading /tmp/resolv.conf.d/resolv.conf.auto
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 178.32.31.41#53 for domain bit
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 176.58.118.172#53 for domain bit
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain glue
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain glue
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain glue
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain parody
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain parody
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain parody
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain dyn
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain dyn
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain dyn
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain bbs
Fri Dec 22 15:15:01 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain bbs
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain bbs
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain free
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain free
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain free
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain fur
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain fur
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain fur
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain geek
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain geek
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain geek
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain gopher
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain gopher
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain gopher
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain indy
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.211.32.162#53 for domain indy
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 95.142.171.235#53 for domain indy
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using nameserver 66.244.95.20#53 for domain ing
Fri Dec 22 15:15:02 2023 daemon.warn dnsmasq[1243]: ignoring nameserver 192.168.1.1 - local interface
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for test
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for onion
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for localhost
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for local
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for invalid
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for bind
Fri Dec 22 15:15:02 2023 daemon.info dnsmasq[1243]: using only locally-known addresses for lan
Fri Dec 22 15:15:03 2023 daemon.info dnsmasq[1243]: read /etc/hosts - 5 addresses
Fri Dec 22 15:15:03 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Fri Dec 22 15:15:03 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/dhcp.cfg01411c.1811 - 0 addresses
Fri Dec 22 15:15:03 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/odhcpd - 0 addresses
Fri Dec 22 15:16:06 2023 daemon.info dnsmasq[1243]: read /etc/hosts - 5 addresses
Fri Dec 22 15:16:06 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Fri Dec 22 15:16:06 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/dhcp.cfg01411c.1811 - 0 addresses
Fri Dec 22 15:16:06 2023 daemon.info dnsmasq[1243]: read /tmp/hosts/odhcpd - 1 addresses
Fri Dec 22 15:16:06 2023 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY
Fri Dec 22 15:16:06 2023 kern.info kernel: [   55.291017] br-lan: port 2(wlan0) entered blocking state
Fri Dec 22 15:16:06 2023 kern.info kernel: [   55.296467] br-lan: port 2(wlan0) entered disabled state
Fri Dec 22 15:16:06 2023 kern.info kernel: [   55.302147] device wlan0 entered promiscuous mode
Fri Dec 22 15:16:06 2023 kern.info kernel: [   55.455274] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Fri Dec 22 15:16:06 2023 kern.info kernel: [   55.462021] br-lan: port 2(wlan0) entered blocking state
Fri Dec 22 15:16:06 2023 kern.info kernel: [   55.467491] br-lan: port 2(wlan0) entered forwarding state
Fri Dec 22 15:16:06 2023 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->ENABLED
Fri Dec 22 15:16:06 2023 daemon.notice hostapd: wlan0: AP-ENABLED
Fri Dec 22 15:16:08 2023 daemon.notice netifd: Wireless device 'radio0' is now up
Fri Dec 22 15:16:08 2023 daemon.notice netifd: Network device 'wlan0' link is up
Fri Dec 22 15:16:10 2023 daemon.notice procd: /etc/rc.d/S90ddns_gargoyle: ERROR: No valid dynamic DNS service configurations defined
Fri Dec 22 15:16:10 2023 daemon.notice procd: /etc/rc.d/S90ddns_gargoyle: (Did you specify correct configuration file path?)
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[1243]: exiting on receipt of SIGTERM
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: started, version 2.86 cachesize 150
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: DNS service limited to local subnets
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: UBus support enabled: connected to system bus
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq-dhcp[2607]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 178.32.31.41#53 for domain bit
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 176.58.118.172#53 for domain bit
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain glue
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain glue
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain glue
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain parody
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain parody
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain parody
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain dyn
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain dyn
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain dyn
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain bbs
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain bbs
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain bbs
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain free
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain free
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain free
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain fur
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain fur
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain fur
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain geek
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain geek
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain geek
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain gopher
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain gopher
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain gopher
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain indy
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain indy
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain indy
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain ing
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for test
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for onion
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for localhost
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for local
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for invalid
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for bind
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for lan
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: reading /tmp/resolv.conf.d/resolv.conf.auto
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 178.32.31.41#53 for domain bit
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 176.58.118.172#53 for domain bit
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain glue
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain glue
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain glue
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain parody
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain parody
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain parody
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain dyn
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain dyn
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain dyn
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain bbs
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain bbs
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain bbs
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain free
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain free
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain free
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain fur
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain fur
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain fur
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain geek
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain geek
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain geek
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain gopher
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain gopher
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain gopher
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain indy
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.211.32.162#53 for domain indy
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 95.142.171.235#53 for domain indy
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using nameserver 66.244.95.20#53 for domain ing
Fri Dec 22 15:16:11 2023 daemon.warn dnsmasq[2607]: ignoring nameserver 192.168.1.1 - local interface
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for test
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for onion
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for localhost
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for local
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for invalid
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for bind
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: using only locally-known addresses for lan
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: read /etc/hosts - 5 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: read /tmp/hosts/odhcpd - 1 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq-dhcp[2607]: read /etc/ethers - 0 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: read /etc/hosts - 5 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq[2607]: read /tmp/hosts/odhcpd - 1 addresses
Fri Dec 22 15:16:11 2023 daemon.info dnsmasq-dhcp[2607]: read /etc/ethers - 0 addresses
Fri Dec 22 15:16:12 2023 daemon.info procd: - init complete -
Fri Dec 22 15:16:13 2023 daemon.info hostapd: wlan0: STA 6c:2f:8a:cb:4a:25 IEEE 802.11: authenticated
Fri Dec 22 15:16:13 2023 daemon.info hostapd: wlan0: STA 6c:2f:8a:cb:4a:25 IEEE 802.11: associated (aid 1)
Fri Dec 22 15:16:13 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED 6c:2f:8a:cb:4a:25
Fri Dec 22 15:16:13 2023 daemon.info hostapd: wlan0: STA 6c:2f:8a:cb:4a:25 RADIUS: starting accounting session C2FB433ED52B6025
Fri Dec 22 15:16:14 2023 daemon.info dnsmasq-dhcp[2607]: DHCPREQUEST(br-lan) 192.168.1.209 6c:2f:8a:cb:4a:25
Fri Dec 22 15:16:14 2023 daemon.info dnsmasq-dhcp[2607]: DHCPACK(br-lan) 192.168.1.209 6c:2f:8a:cb:4a:25 Galaxy-Tab-A7-Lite
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:17 2023 daemon.err uhttpd[2127]: sh: write error: Broken pipe
Fri Dec 22 15:16:24 2023 daemon.info dnsmasq-dhcp[2607]: DHCPDISCOVER(br-lan) 192.168.1.122 00:d8:61:08:db:4e
Fri Dec 22 15:16:24 2023 daemon.info dnsmasq-dhcp[2607]: DHCPOFFER(br-lan) 192.168.1.122 00:d8:61:08:db:4e
Fri Dec 22 15:16:24 2023 daemon.info dnsmasq-dhcp[2607]: DHCPREQUEST(br-lan) 192.168.1.122 00:d8:61:08:db:4e
Fri Dec 22 15:16:24 2023 daemon.info dnsmasq-dhcp[2607]: DHCPACK(br-lan) 192.168.1.122 00:d8:61:08:db:4e DESKTOP-GMCROMN
Fri Dec 22 15:16:25 2023 daemon.notice hostapd: wlan0: STA f4:f3:09:ba:35:13 IEEE 802.11: did not acknowledge authentication response
Fri Dec 22 15:16:25 2023 daemon.info hostapd: wlan0: STA f4:f3:09:ba:35:13 IEEE 802.11: associated (aid 2)
Fri Dec 22 15:16:25 2023 daemon.notice hostapd: wlan0: AP-STA-CONNECTED f4:f3:09:ba:35:13
Fri Dec 22 15:16:25 2023 daemon.info hostapd: wlan0: STA f4:f3:09:ba:35:13 RADIUS: starting accounting session 799CEB3BB062C34D
Fri Dec 22 15:16:25 2023 daemon.info dnsmasq-dhcp[2607]: DHCPREQUEST(br-lan) 192.168.1.143 f4:f3:09:ba:35:13
Fri Dec 22 15:16:25 2023 daemon.info dnsmasq-dhcp[2607]: DHCPACK(br-lan) 192.168.1.143 f4:f3:09:ba:35:13 Galaxy-Tab-A7-Lite
Success

Jest gdzieś w sieci poradnik krok po kroku z tym extrootem ? Bo już mnie krew zalewa.

25 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,529

Odp: 1.14 extroot i problem

A teraz pokaz wynik block info

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona