U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:47:06)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 408k for U-Boot at: 87f98000
Reserving 16448k for malloc() at: 86f88000
Reserving 44 Bytes for Board Info at: 86f87fd4
Reserving 36 Bytes for Global Data at: 86f87fb0
Reserving 128k for boot params() at: 86f67fb0
Stack Pointer at: 86f67f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
run command setenv serverip 192.168.0.66;setenv ipaddr 192.168.0.86
run command tftp 0x80060000 ArcherC7v5_tp_recovery.bin
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Download Filename 'ArcherC7v5_tp_recovery.bin'.
Download to address: 0x80060000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
T ################################
done
Bytes transferred = 15568476 (ed8e5c hex)
Firmware downloaded... filesize = 0xed8e5c fileaddr = 0x80060000.
Firmware Recovery file length : 15568476
Firmware process id 2.
handle_fw_cloud 138
Image verify OK!
Firmware file Verify ok!
[Error]sysmgr_proinfo_buildStruct(): 659 @ unknown id(device_name), skip it.
[Error]sysmgr_proinfo_buildStruct(): 659 @ unknown id(country), skip it.
[Error]sysmgr_proinfo_buildStruct(): 659 @ unknown id(hw_ver), skip it.
Firmware supports, check OK.
(curFw_ver, newFw_ver) == (7.0, 1.0)
[NM_Error](nm_checkSoftVer) 00962: Firmwave not supports, check failed.
[NM_Error](nm_checkUpdateContent) 01219: the firmware software version dismatched
[NM_Error](nm_buildUpgradeStruct) 01314: checkUpdateContent failed.
recovery failed.
now restart...
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:47:06)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 408k for U-Boot at: 87f98000
Reserving 16448k for malloc() at: 86f88000
Reserving 44 Bytes for Board Info at: 86f87fd4
Reserving 36 Bytes for Global Data at: 86f87fb0
Reserving 128k for boot params() at: 86f67fb0
Stack Pointer at: 86f67f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
factory boot check integer ok.
factory boot load fs uboot len 131072 to addr 0x80010000.
Hit any key to stop autoboot: 0
## Starting application at 0x80010000 ...
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:41:00)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 125k for U-Boot at: 87fe0000
Reserving 16448k for malloc() at: 86fd0000
Reserving 44 Bytes for Board Info at: 86fcffd4
Reserving 36 Bytes for Global Data at: 86fcffb0
Reserving 128k for boot params() at: 86faffb0
Stack Pointer at: 86faff98
Now running in RAM - U-Boot at: 87fe0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot: 0
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-5.15.134
Created: 2023-10-28 7:19:46 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2328797 Bytes = 2.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 5.15.134 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23004-7f0db09513) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Sat Oct 28 07:19:46 2023
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link Archer A7 v5
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 120880K/131072K available (6077K kernel code, 591K rwdata, 780K rodata, 1184K init, 217K bss, 10192K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000001] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008289] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.074816] pid_max: default: 32768 minimum: 301
[ 0.080514] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.088253] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.103096] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.113511] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.120860] pinctrl core: initialized pinctrl subsystem
[ 0.128045] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.134870] thermal_sys: Registered thermal governor 'step_wise'
[ 0.147229] clocksource: Switched to clocksource MIPS
[ 0.160244] NET: Registered PF_INET protocol family
[ 0.165624] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.174173] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.183051] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.191242] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.199342] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.206781] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.213635] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.220587] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.228346] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.234353] PCI: CLS 0 bytes, default 32
[ 0.241823] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.253408] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.259631] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.271301] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.282731] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.289454] gpio-export gpio-export: 1 gpio(s) exported
[ 0.295957] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.305224] printk: console [ttyS0] disabled
[ 0.309844] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.318966] printk: console [ttyS0] enabled
[ 0.318966] printk: console [ttyS0] enabled
[ 0.328033] printk: bootconsole [early0] disabled
[ 0.328033] printk: bootconsole [early0] disabled
[ 0.356707] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.361812] 7 fixed-partitions partitions found on MTD device spi0.0
[ 0.368449] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.375313] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.382483] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.389390] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.396691] Creating 7 MTD partitions on "spi0.0":
[ 0.401707] 0x000000000000-0x000000020000 : "factory-uboot"
[ 0.412367] 0x000000020000-0x000000040000 : "u-boot"
[ 0.418539] 0x000000040000-0x000000f00000 : "firmware"
[ 0.426449] 2 uimage-fw partitions found on MTD device firmware
[ 0.432635] Creating 2 MTD partitions on "firmware":
[ 0.437783] 0x000000000000-0x000000240000 : "kernel"
[ 0.444681] 0x000000240000-0x000000ec0000 : "rootfs"
[ 0.450801] mtd: setting mtd4 (rootfs) as root device
[ 0.456885] 1 squashfs-split partitions found on MTD device rootfs
[ 0.463357] 0x000000990000-0x000000ec0000 : "rootfs_data"
[ 0.470733] 0x000000f40000-0x000000f60000 : "info"
[ 0.476753] 0x000000f60000-0x000000fb0000 : "config"
[ 0.484378] 0x000000fc0000-0x000000fd0000 : "partition-table"
[ 0.491411] 0x000000ff0000-0x000001000000 : "art"
[ 1.231333] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.888872] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.900210] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.907120] i2c_dev: i2c /dev entries driver
[ 1.914778] NET: Registered PF_INET6 protocol family
[ 1.932650] Segment Routing with IPv6
[ 1.936519] In-situ OAM (IOAM) with IPv6
[ 1.940773] NET: Registered PF_PACKET protocol family
[ 1.946099] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.959813] 8021q: 802.1Q VLAN Support v1.8
[ 1.965385] PCI host bridge to bus 0000:00
[ 1.969682] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.976788] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.982553] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.990787] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 1.997024] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 2.004097] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.011109] pci 0000:00:00.0: supports D1 D2
[ 2.016507] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.023397] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 2.030983] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 2.050328] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.064002] Freeing unused kernel image (initmem) memory: 1184K
[ 2.070159] This architecture does not have kernel memory protection.
[ 2.076820] Run /sbin/init as init process
[ 2.784192] init: Console is alive
[ 2.788285] init: - watchdog -
[ 5.617898] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.683661] usbcore: registered new interface driver usbfs
[ 5.689510] usbcore: registered new interface driver hub
[ 5.695091] usbcore: registered new device driver usb
[ 5.763308] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.780891] SCSI subsystem initialized
[ 5.790648] fsl-ehci: Freescale EHCI Host controller driver
[ 5.799450] ehci-platform: EHCI generic platform driver
[ 5.805193] ehci-platform 1b000000.usb: EHCI Host Controller
[ 5.811126] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 5.819405] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 5.847247] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 5.854550] hub 1-0:1.0: USB hub found
[ 5.859254] hub 1-0:1.0: 1 port detected
[ 5.872646] usbcore: registered new interface driver usb-storage
[ 5.881637] usbcore: registered new interface driver uas
[ 5.888489] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.906463] init: - preinit -
[ 7.560027] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.011084] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.282565] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.710442] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.775052] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
[ 9.867309] eth0: link up (1000Mbps/Full duplex)
[ 9.872129] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.901619] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 9.927646] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 12.162562] mount_root: loading kmods from internal overlay
[ 12.224044] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.237294] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 13.426194] jffs2: notice: (479) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (6 unchecked, 3 orphan) and 15 of xref (3 dead, 0 orphan) found.
[ 13.443084] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 13.456179] block: extroot: not configured
[ 13.535064] jffs2: notice: (477) jffs2_build_xattr_subsystem: complete building xattr subsystem, 12 of xdatum (6 unchecked, 3 orphan) and 15 of xref (3 dead, 0 orphan) found.
[ 13.552989] mount_root: loading kmods from internal overlay
[ 13.606671] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 13.618087] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 14.486717] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.502772] block: extroot: not configured
[ 14.508710] mount_root: switching to jffs2 overlay
[ 14.516172] overlayfs: upper fs does not support tmpfile.
[ 14.528382] urandom-seed: Seeding with /etc/urandom.seed
[ 14.618962] eth0: link down
[ 14.642173] procd: - early -
[ 14.645463] procd: - watchdog -
[ 15.459928] procd: - watchdog -
[ 15.463695] procd: - ubus -
[ 15.695384] random: jshn: uninitialized urandom read (4 bytes read)
[ 15.711433] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.724237] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.811306] procd: - init -
Please press Enter to activate this console.
[ 17.164283] random: jshn: uninitialized urandom read (4 bytes read)
[ 17.196659] random: ubusd: uninitialized urandom read (4 bytes read)
[ 18.209430] kmodloader: loading kernel modules from /etc/modules.d/*
[ 18.967497] tun: Universal TUN/TAP device driver, 1.6
[ 19.038508] ksmbd: The ksmbd server is experimental, use at your own risk.
[ 19.107483] ntfs3: Max link count 4000
[ 19.111374] ntfs3: Enabled Linux POSIX ACLs support
[ 19.163906] usbcore: registered new interface driver cdc_acm
[ 19.169811] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 19.219837] usbcore: registered new interface driver cdc_wdm
[ 19.258197] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 19.265943] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 19.376547] usbcore: registered new interface driver usblp
[ 19.420945] usbcore: registered new interface driver usbserial_generic
[ 19.427834] usbserial: USB Serial support registered for generic
[ 19.473116] usbcore: registered new interface driver cdc_ether
[ 19.509655] usbcore: registered new interface driver cdc_ncm
[ 19.582355] usbcore: registered new interface driver huawei_cdc_ncm
[ 20.483502] PPP generic driver version 2.4.2
[ 20.499134] NET: Registered PF_PPPOX protocol family
[ 20.539734] usbcore: registered new interface driver qmi_wwan
[ 20.579436] usbcore: registered new interface driver rndis_host
[ 20.609279] usbcore: registered new interface driver sierra
[ 20.615118] usbserial: USB Serial support registered for Sierra USB modem
[ 20.675641] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 20.683783] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 20.890450] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 20.938464] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 20.945096] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 21.298715] urngd: v1.0.2 started.
[ 22.992322] random: crng init done
[ 22.995856] random: 37 urandom warning(s) missed due to ratelimiting
[ 34.394434] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 34.404031] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 34.415979] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[ 34.531613] ath10k_pci 0000:00:00.0: Loading BDF type 0
[ 35.286722] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 36.280070] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 36.296902] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 36.303406] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 36.311726] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 36.361828] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 36.374802] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 36.569468] usbcore: registered new interface driver cdc_mbim
[ 36.626880] usbcore: registered new interface driver option
[ 36.632776] usbserial: USB Serial support registered for GSM modem (1-port)
[ 36.683672] usbcore: registered new interface driver qcserial
[ 36.689752] usbserial: USB Serial support registered for Qualcomm USB modem
[ 36.747735] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[ 36.786536] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 63.309278] eth0: link up (1000Mbps/Full duplex)
[ 63.314101] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 63.337718] br-lan: port 1(eth0.1) entered blocking state
[ 63.343319] br-lan: port 1(eth0.1) entered disabled state
[ 63.349229] device eth0.1 entered promiscuous mode
[ 63.354187] device eth0 entered promiscuous mode
[ 63.408235] br-lan: port 1(eth0.1) entered blocking state
[ 63.413836] br-lan: port 1(eth0.1) entered forwarding state
[ 64.337582] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 64.345329] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is down
[ 65.098582] ksmbd: The ksmbd server is experimental, use at your own risk.
[ 67.457815] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
[ 305.234400] reboot: Restarting system
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:47:06)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 408k for U-Boot at: 87f98000
Reserving 16448k for malloc() at: 86f88000
Reserving 44 Bytes for Board Info at: 86f87fd4
Reserving 36 Bytes for Global Data at: 86f87fb0
Reserving 128k for boot params() at: 86f67fb0
Stack Pointer at: 86f67f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
factory boot check integer ok.
factory boot load fs uboot len 131072 to addr 0x80010000.
Hit any key to stop autoboot: 0
## Starting application at 0x80010000 ...
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:41:00)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 125k for U-Boot at: 87fe0000
Reserving 16448k for malloc() at: 86fd0000
Reserving 44 Bytes for Board Info at: 86fcffd4
Reserving 36 Bytes for Global Data at: 86fcffb0
Reserving 128k for boot params() at: 86faffb0
Stack Pointer at: 86faff98
Now running in RAM - U-Boot at: 87fe0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot: 0
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-5.15.134
Created: 2023-10-28 7:19:46 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2328797 Bytes = 2.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 5.15.134 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23004-7f0db09513) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Sat Oct 28 07:19:46 2023
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link Archer A7 v5
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 120880K/131072K available (6077K kernel code, 591K rwdata, 780K rodata, 1184K init, 217K bss, 10192K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000001] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008288] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.074816] pid_max: default: 32768 minimum: 301
[ 0.080516] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.088251] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.103067] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.113486] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.120836] pinctrl core: initialized pinctrl subsystem
[ 0.128022] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.134850] thermal_sys: Registered thermal governor 'step_wise'
[ 0.147098] clocksource: Switched to clocksource MIPS
[ 0.160114] NET: Registered PF_INET protocol family
[ 0.165495] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.174051] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.182935] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.191124] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.199215] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.206657] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.213512] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.220471] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.228228] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.234236] PCI: CLS 0 bytes, default 32
[ 0.241703] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.253272] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.259489] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.271162] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.282583] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.289312] gpio-export gpio-export: 1 gpio(s) exported
[ 0.295826] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.305054] printk: console [ttyS0] disabled
[ 0.309676] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.318800] printk: console [ttyS0] enabled
[ 0.318800] printk: console [ttyS0] enabled
[ 0.327867] printk: bootconsole [early0] disabled
[ 0.327867] printk: bootconsole [early0] disabled
[ 0.356704] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.361807] 7 fixed-partitions partitions found on MTD device spi0.0
[ 0.368442] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.375307] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.382474] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.389375] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.396677] Creating 7 MTD partitions on "spi0.0":
[ 0.401695] 0x000000000000-0x000000020000 : "factory-uboot"
[ 0.412352] 0x000000020000-0x000000040000 : "u-boot"
[ 0.418526] 0x000000040000-0x000000f00000 : "firmware"
[ 0.426432] 2 uimage-fw partitions found on MTD device firmware
[ 0.432621] Creating 2 MTD partitions on "firmware":
[ 0.437769] 0x000000000000-0x000000240000 : "kernel"
[ 0.444664] 0x000000240000-0x000000ec0000 : "rootfs"
[ 0.450783] mtd: setting mtd4 (rootfs) as root device
[ 0.456869] 1 squashfs-split partitions found on MTD device rootfs
[ 0.463334] 0x000000990000-0x000000ec0000 : "rootfs_data"
[ 0.470696] 0x000000f40000-0x000000f60000 : "info"
[ 0.476708] 0x000000f60000-0x000000fb0000 : "config"
[ 0.484331] 0x000000fc0000-0x000000fd0000 : "partition-table"
[ 0.491363] 0x000000ff0000-0x000001000000 : "art"
[ 1.231210] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.888743] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.900074] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.906984] i2c_dev: i2c /dev entries driver
[ 1.914654] NET: Registered PF_INET6 protocol family
[ 1.932584] Segment Routing with IPv6
[ 1.936452] In-situ OAM (IOAM) with IPv6
[ 1.940702] NET: Registered PF_PACKET protocol family
[ 1.946030] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.959744] 8021q: 802.1Q VLAN Support v1.8
[ 1.965270] PCI host bridge to bus 0000:00
[ 1.969569] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.976676] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.982440] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.990673] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 1.996913] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 2.003983] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.010986] pci 0000:00:00.0: supports D1 D2
[ 2.016383] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.023276] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 2.030863] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 2.050188] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.063862] Freeing unused kernel image (initmem) memory: 1184K
[ 2.070021] This architecture does not have kernel memory protection.
[ 2.076680] Run /sbin/init as init process
[ 2.784148] init: Console is alive
[ 2.788241] init: - watchdog -
[ 5.618081] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.683534] usbcore: registered new interface driver usbfs
[ 5.689390] usbcore: registered new interface driver hub
[ 5.694972] usbcore: registered new device driver usb
[ 5.763827] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.781504] SCSI subsystem initialized
[ 5.791234] fsl-ehci: Freescale EHCI Host controller driver
[ 5.799998] ehci-platform: EHCI generic platform driver
[ 5.805740] ehci-platform 1b000000.usb: EHCI Host Controller
[ 5.811665] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 5.819945] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 5.847117] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 5.854409] hub 1-0:1.0: USB hub found
[ 5.859107] hub 1-0:1.0: 1 port detected
[ 5.872499] usbcore: registered new interface driver usb-storage
[ 5.881517] usbcore: registered new interface driver uas
[ 5.888381] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.906349] init: - preinit -
[ 7.561536] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.011032] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.283256] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.722878] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.784913] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
[ 9.877167] eth0: link up (1000Mbps/Full duplex)
[ 9.881990] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.910714] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 9.937508] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 12.166587] mount_root: loading kmods from internal overlay
[ 12.228062] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.241244] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 13.429915] jffs2: notice: (479) jffs2_build_xattr_subsystem: complete building xattr subsystem, 15 of xdatum (6 unchecked, 4 orphan) and 18 of xref (4 dead, 0 orphan) found.
[ 13.446777] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 13.460420] block: extroot: not configured
[ 13.535161] jffs2: notice: (477) jffs2_build_xattr_subsystem: complete building xattr subsystem, 15 of xdatum (6 unchecked, 4 orphan) and 18 of xref (4 dead, 0 orphan) found.
[ 13.558035] mount_root: loading kmods from internal overlay
[ 13.613893] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 13.624382] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 14.494896] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 14.505996] block: extroot: not configured
[ 14.511962] mount_root: switching to jffs2 overlay
[ 14.520476] overlayfs: upper fs does not support tmpfile.
[ 14.532322] urandom-seed: Seeding with /etc/urandom.seed
[ 14.628148] eth0: link down
[ 14.651327] procd: - early -
[ 14.654632] procd: - watchdog -
[ 15.469145] procd: - watchdog -
[ 15.488134] procd: - ubus -
[ 15.705313] random: jshn: uninitialized urandom read (4 bytes read)
[ 15.712046] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.721597] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.821708] procd: - init -
Please press Enter to activate this console.
[ 17.112900] random: jshn: uninitialized urandom read (4 bytes read)
[ 17.136483] random: ubusd: uninitialized urandom read (4 bytes read)
[ 18.171591] kmodloader: loading kernel modules from /etc/modules.d/*
[ 18.911988] tun: Universal TUN/TAP device driver, 1.6
[ 18.997424] ksmbd: The ksmbd server is experimental, use at your own risk.
[ 19.057389] ntfs3: Max link count 4000
[ 19.061282] ntfs3: Enabled Linux POSIX ACLs support
[ 19.123763] usbcore: registered new interface driver cdc_acm
[ 19.129665] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 19.188688] usbcore: registered new interface driver cdc_wdm
[ 19.228280] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 19.236030] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 19.349068] usbcore: registered new interface driver usblp
[ 19.380523] usbcore: registered new interface driver usbserial_generic
[ 19.387407] usbserial: USB Serial support registered for generic
[ 19.424919] usbcore: registered new interface driver cdc_ether
[ 19.459526] usbcore: registered new interface driver cdc_ncm
[ 19.540244] usbcore: registered new interface driver huawei_cdc_ncm
[ 20.444370] PPP generic driver version 2.4.2
[ 20.478301] NET: Registered PF_PPPOX protocol family
[ 20.519597] usbcore: registered new interface driver qmi_wwan
[ 20.559337] usbcore: registered new interface driver rndis_host
[ 20.574471] usbcore: registered new interface driver sierra
[ 20.580389] usbserial: USB Serial support registered for Sierra USB modem
[ 20.661412] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 20.669571] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 20.870293] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 20.918303] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 20.924949] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 21.165824] urngd: v1.0.2 started.
[ 22.961011] random: crng init done
[ 22.964544] random: 37 urandom warning(s) missed due to ratelimiting
[ 34.411172] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 34.420779] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 34.432736] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:47:06)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 408k for U-Boot at: 87f98000
Reserving 16448k for malloc() at: 86f88000
Reserving 44 Bytes for Board Info at: 86f87fd4
Reserving 36 Bytes for Global Data at: 86f87fb0
Reserving 128k for boot params() at: 86f67fb0
Stack Pointer at: 86f67f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
factory boot check integer ok.
factory boot load fs uboot len 131072 to addr 0x80010000.
Hit any key to stop autoboot: 0
## Starting application at 0x80010000 ...
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:41:00)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 125k for U-Boot at: 87fe0000
Reserving 16448k for malloc() at: 86fd0000
Reserving 44 Bytes for Board Info at: 86fcffd4
Reserving 36 Bytes for Global Data at: 86fcffb0
Reserving 128k for boot params() at: 86faffb0
Stack Pointer at: 86faff98
Now running in RAM - U-Boot at: 87fe0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot: 0
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-5.15.134
Created: 2023-10-28 7:19:46 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2328797 Bytes = 2.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 5.15.134 (cezary@eko.one.pl) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23004-7f0db09513) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Sat Oct 28 07:19:46 2023
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] MIPS: machine is TP-Link Archer A7 v5
[ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 120880K/131072K available (6077K kernel code, 591K rwdata, 780K rodata, 1184K init, 217K bss, 10192K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 775.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
[ 0.000001] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
[ 0.008288] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.074816] pid_max: default: 32768 minimum: 301
[ 0.080515] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.088252] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.103094] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.113511] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.120860] pinctrl core: initialized pinctrl subsystem
[ 0.128050] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.134883] thermal_sys: Registered thermal governor 'step_wise'
[ 0.147148] clocksource: Switched to clocksource MIPS
[ 0.160164] NET: Registered PF_INET protocol family
[ 0.165541] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.174097] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.182975] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.191167] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.199268] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.206706] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.213560] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.220514] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.228272] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.234278] PCI: CLS 0 bytes, default 32
[ 0.241735] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.253304] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.259522] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.271200] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.282645] pinctrl-single 1804002c.pinmux: 544 pins, size 68
[ 0.289367] gpio-export gpio-export: 1 gpio(s) exported
[ 0.295881] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.305139] printk: console [ttyS0] disabled
[ 0.309760] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A
[ 0.318883] printk: console [ttyS0] enabled
[ 0.318883] printk: console [ttyS0] enabled
[ 0.327951] printk: bootconsole [early0] disabled
[ 0.327951] printk: bootconsole [early0] disabled
[ 0.356761] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.361863] 7 fixed-partitions partitions found on MTD device spi0.0
[ 0.368499] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.375363] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.382534] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.389441] OF: Bad cell count for /ahb/spi@1f000000/flash@0/partitions
[ 0.396745] Creating 7 MTD partitions on "spi0.0":
[ 0.401769] 0x000000000000-0x000000020000 : "factory-uboot"
[ 0.412406] 0x000000020000-0x000000040000 : "u-boot"
[ 0.418577] 0x000000040000-0x000000f00000 : "firmware"
[ 0.426496] 2 uimage-fw partitions found on MTD device firmware
[ 0.432687] Creating 2 MTD partitions on "firmware":
[ 0.437836] 0x000000000000-0x000000240000 : "kernel"
[ 0.444758] 0x000000240000-0x000000ec0000 : "rootfs"
[ 0.450871] mtd: setting mtd4 (rootfs) as root device
[ 0.456948] 1 squashfs-split partitions found on MTD device rootfs
[ 0.463417] 0x000000990000-0x000000ec0000 : "rootfs_data"
[ 0.470807] 0x000000f40000-0x000000f60000 : "info"
[ 0.476825] 0x000000f60000-0x000000fb0000 : "config"
[ 0.484428] 0x000000fc0000-0x000000fd0000 : "partition-table"
[ 0.491477] 0x000000ff0000-0x000001000000 : "art"
[ 1.231255] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 1.888793] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.900117] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 1.907029] i2c_dev: i2c /dev entries driver
[ 1.914695] NET: Registered PF_INET6 protocol family
[ 1.932568] Segment Routing with IPv6
[ 1.936437] In-situ OAM (IOAM) with IPv6
[ 1.940689] NET: Registered PF_PACKET protocol family
[ 1.946015] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.959733] 8021q: 802.1Q VLAN Support v1.8
[ 1.965284] PCI host bridge to bus 0000:00
[ 1.969580] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 1.976688] pci_bus 0000:00: root bus resource [io 0x0000]
[ 1.982451] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.990683] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 1.996922] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 2.003995] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 2.010997] pci 0000:00:00.0: supports D1 D2
[ 2.016392] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.023285] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 2.030874] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 2.050169] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.063848] Freeing unused kernel image (initmem) memory: 1184K
[ 2.070004] This architecture does not have kernel memory protection.
[ 2.076664] Run /sbin/init as init process
[ 2.784322] init: Console is alive
[ 2.788418] init: - watchdog -
[ 5.617983] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.683820] usbcore: registered new interface driver usbfs
[ 5.689668] usbcore: registered new interface driver hub
[ 5.695248] usbcore: registered new device driver usb
[ 5.763413] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.781032] SCSI subsystem initialized
[ 5.790798] fsl-ehci: Freescale EHCI Host controller driver
[ 5.799583] ehci-platform: EHCI generic platform driver
[ 5.805321] ehci-platform 1b000000.usb: EHCI Host Controller
[ 5.811248] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 5.819528] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 5.847165] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 5.854451] hub 1-0:1.0: USB hub found
[ 5.859157] hub 1-0:1.0: 1 port detected
[ 5.872558] usbcore: registered new interface driver usb-storage
[ 5.881552] usbcore: registered new interface driver uas
[ 5.888413] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.906391] init: - preinit -
[ 7.562134] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.011474] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.283663] random: jshn: uninitialized urandom read (4 bytes read)
[ 8.723356] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.785118] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
[ 9.877238] eth0: link up (1000Mbps/Full duplex)
[ 9.882063] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9.911021] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 9.937599] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 12.167530] mount_root: loading kmods from internal overlay
[ 12.229106] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.242279] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 13.452768] block: attempting to load /etc/config/fstab
[ 13.469085] block: unable to load configuration (fstab: Entry not found)
[ 13.476330] block: no usable configuration
[ 13.481614] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 13.496288] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 13.585662] eth0: link down
[ 13.609030] procd: - early -
[ 13.612323] procd: - watchdog -
[ 14.430611] procd: - watchdog -
[ 14.434387] procd: - ubus -
[ 14.638126] random: jshn: uninitialized urandom read (4 bytes read)
[ 14.645236] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.672966] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.766045] procd: - init -
Please press Enter to activate this console.
[ 16.042970] random: jshn: uninitialized urandom read (4 bytes read)
[ 16.066516] random: ubusd: uninitialized urandom read (4 bytes read)
[ 17.074096] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.830228] tun: Universal TUN/TAP device driver, 1.6
[ 17.897482] ksmbd: The ksmbd server is experimental, use at your own risk.
[ 17.957466] ntfs3: Max link count 4000
[ 17.961355] ntfs3: Enabled Linux POSIX ACLs support
[ 18.028644] usbcore: registered new interface driver cdc_acm
[ 18.034506] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 18.083025] usbcore: registered new interface driver cdc_wdm
[ 18.118310] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
[ 18.126058] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
[ 18.233317] usbcore: registered new interface driver usblp
[ 18.274117] usbcore: registered new interface driver usbserial_generic
[ 18.281020] usbserial: USB Serial support registered for generic
[ 18.318889] usbcore: registered new interface driver cdc_ether
[ 18.349531] usbcore: registered new interface driver cdc_ncm
[ 18.426524] usbcore: registered new interface driver huawei_cdc_ncm
[ 19.304056] PPP generic driver version 2.4.2
[ 19.348334] NET: Registered PF_PPPOX protocol family
[ 19.356531] usbcore: registered new interface driver qmi_wwan
[ 19.399434] usbcore: registered new interface driver rndis_host
[ 19.435129] usbcore: registered new interface driver sierra
[ 19.441042] usbserial: USB Serial support registered for Sierra USB modem
[ 19.513907] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 19.522053] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 19.710433] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 19.768094] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 19.774754] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 20.057654] urngd: v1.0.2 started.
[ 21.802698] random: crng init done
[ 21.806234] random: 37 urandom warning(s) missed due to ratelimiting
[ 24.938628] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 24.948212] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 24.960182] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[ 25.067674] ath10k_pci 0000:00:00.0: Loading BDF type 0
[ 25.823359] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 26.815079] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 26.831894] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 26.838384] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 26.846669] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 26.896773] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 26.909730] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 27.119887] usbcore: registered new interface driver cdc_mbim
[ 27.215441] usbcore: registered new interface driver option
[ 27.221342] usbserial: USB Serial support registered for GSM modem (1-port)
[ 27.235846] usbcore: registered new interface driver qcserial
[ 27.241937] usbserial: USB Serial support registered for Qualcomm USB modem
[ 27.304176] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=2
[ 27.364950] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 77.949160] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 77.956294] jffs2_build_filesystem(): unlocking the mtd device...
[ 77.956301] done.
[ 77.964707] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 78.692182] eth0: link up (1000Mbps/Full duplex)
[ 78.722183] br-lan: port 1(eth0.1) entered blocking state
[ 78.727847] br-lan: port 1(eth0.1) entered disabled state
[ 78.733694] device eth0.1 entered promiscuous mode
[ 78.738698] device eth0 entered promiscuous mode
[ 78.767981] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 78.814599] br-lan: port 1(eth0.1) entered blocking state
[ 78.820248] br-lan: port 1(eth0.1) entered forwarding state
[ 79.699646] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 104.596098] done.
[ 104.598144] jffs2: notice: (3223) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 104.961659] overlayfs: upper fs does not support tmpfile.
[ 106.055684] ksmbd: The ksmbd server is experimental, use at your own risk.
[ 106.898164] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is down
[ 108.977635] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up
Watchdog handover: fd=3
- watchdog -
Watchdog did not previously reset the system
Sat Oct 28 10:18:59 CEST 2023 upgrade: Sending TERM to remaining processes ...
Sat Oct 28 10:19:03 CEST 2023 upgrade: Sending KILL to remaining processes ...
[ 3579.321200] stage2 (4916): drop_caches: 3
Sat Oct 28 10:19:09 CEST 2023 upgrade: Switching to ramdisk...
mount: mounting /dev/mtdblock5 on /overlay failed: Resource busy
[ 3583.773254] VFS: Busy inodes after unmount of jffs2. Self-destruct in 5 seconds. Have a nice day...
Sat Oct 28 08:19:14 UTC 2023 upgrade: Performing system upgrade...
[ 3583.864081] do_stage2 (4916): drop_caches: 3
Unlocking firmware ...
Writing from <stdin> to firmware ... [w][ 3588.337190] ksmbd: No IPC daemon response for 20s [w][ 3638.817862] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is down [w][ 3642.977547] Atheros AR8216/AR8236/AR8316 mdio.0:00: Port 2 is up [e]
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:47:06)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 408k for U-Boot at: 87f98000
Reserving 16448k for malloc() at: 86f88000
Reserving 44 Bytes for Board Info at: 86f87fd4
Reserving 36 Bytes for Global Data at: 86f87fb0
Reserving 128k for boot params() at: 86f67fb0
Stack Pointer at: 86f67f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
factory boot check integer ok.
factory boot load fs uboot len 131072 to addr 0x80010000.
Hit any key to stop autoboot: 0
## Starting application at 0x80010000 ...
U-Boot 1.1.4-gcdf6499e-dirty (May 11 2019 - 14:41:00)
ap152 - Dragonfly 1.0
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 125k for U-Boot at: 87fe0000
Reserving 16448k for malloc() at: 86fd0000
Reserving 44 Bytes for Board Info at: 86fcffd4
Reserving 36 Bytes for Global Data at: 86fcffb0
Reserving 128k for boot params() at: 86faffb0
Stack Pointer at: 86faff98
Now running in RAM - U-Boot at: 87fe0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init ::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
SGMII in forced mode
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
Setting 0x181162c0 to 0x40802100
Hit any key to stop autoboot: 0
## Booting image at 9f040000 ...
Bad Magic Number
ath>
