Starting kernel ...

Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Initializing cgroup subsys cpuacct
Linux version 4.1.25 (scl@scl_xa243_152) (gcc version 4.9.4 (Buildroot 2017.05-svn2186) ) #2 SMP PREEMPT Fri Sep 30 15:42:03 CST 2022
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: ZTE ZX279128S
Ignoring memory range 0x0 - 0x40000000
Ignoring memory block 0x0 - 0x20000000
in function:early_mem line: 766 zxic_mem_size = 0x8000000
Memory policy: Data cache writealloc
======= zx_map_io pon =======
======= zx_map_io =======
acl length 0x400000
opc length 0x100000
PERCPU: Embedded 11 pages/cpu @c67c0000 s15276 r8192 d21588 u45056
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32480
Kernel command line: console=ttyAMA0,115200n8 root=/dev/mtdblock4 ro rootfstype=jffs2 mem=128M; U-Boot SGUV2.0.0B05 20220330123115 0x400000 0x0 0x83 0x00
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 97984K/131072K available (5403K kernel code, 305K rwdata, 1976K rodata, 200K init, 243K bss, 33088K reserved, 0K cma-reserved)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .text : 0xc0008000 - 0xc073d03c   (7381 kB)
      .init : 0xc073e000 - 0xc0770000   ( 200 kB)
      .data : 0xc0770000 - 0xc07bc780   ( 306 kB)
       .bss : 0xc07bc780 - 0xc07f96cc   ( 244 kB)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
    Additional per-CPU info printed with stalls.
NR_IRQS:16 nr_irqs:16 16
L2C: platform modifies aux control register: 0x02030000 -> 0x32430000
L2C: platform provided aux values permit register corruption.
L2C: DT/platform modifies aux control register: 0x02030000 -> 0x02430000
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 16 ways, 256 kB
L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x46430001
sched_clock: 64 bits at 600MHz, resolution 1ns, wraps every 2199023255551ns
clocksource arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x8a60dd94a9, max_idle_ns: 440795233082 ns
Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Initializing cgroup subsys blkio
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
Initializing cgroup subsys net_prio
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x400081e0 - 0x40008214
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (4780.85 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
e8_arp_detect_init OK!
DMA: preallocated 2048 KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
genirq: Setting trigger mode 8 for irq 50 failed (gic_set_type+0x0/0x48)
genirq: Setting trigger mode 8 for irq 51 failed (gic_set_type+0x0/0x48)
genirq: Setting trigger mode 3 for irq 63 failed (gic_set_type+0x0/0x48)
genirq: Setting trigger mode 3 for irq 64 failed (gic_set_type+0x0/0x48)
genirq: Setting trigger mode 3 for irq 65 failed (gic_set_type+0x0/0x48)
genirq: Setting trigger mode 3 for irq 66 failed (gic_set_type+0x0/0x48)
[zx279128_init_machine] num_online_cpus:2 num_possible_cpus:2 num_present_cpus:2 num_active_cpus:2
Serial: AMBA PL011 UART driver
94405000.serial: ttyAMA0 at MMIO 0x94404000 (irq = 21, base_baud = 0) is a 
console [ttyAMA0] enabled
Serial: AMBA PL011 UART add port0 success
[INFO]zxic_param_init
[ERROR]zx_vid_load magic_num check failed.
[DEBUG]zxic_param_init zxic soft vid: 0x00000000
[INFO] ZXIC_SOFT_VID:0x00000000
product_vid = 0x00000000
<zxic_gpio_init>(1723):invalid vid!!!!use default!!!
vid=0x00040001-F628S
board id=262145, hardversion=V6.0, boardname=F628S
cpu id=0, vendor=ZX279128S
mux=c157aa9
mux=5effd75
mux=555cccf
mux=1f5f87
gpio_nr=a
led_nr=5
i=0,address=0,attribute=1,bused=1,mode=1,realgpio=56
i=1,address=1,attribute=1,bused=1,mode=1,realgpio=57
i=2,address=2,attribute=1,bused=1,mode=1,realgpio=58
i=3,address=3,attribute=1,bused=1,mode=1,realgpio=59
i=4,address=37,attribute=1,bused=1,mode=1,realgpio=15
i=5,address=73,attribute=0,bused=1,mode=0,realgpio=18
i=6,address=74,attribute=0,bused=1,mode=0,realgpio=21
i=7,address=75,attribute=1,bused=1,mode=1,realgpio=20
i=8,address=76,attribute=0,bused=1,mode=1,realgpio=12
i=9,address=78,attribute=0,bused=1,mode=0,realgpio=40
i=37,15,1,0,1
i=73,18,0,-1,1
i=74,21,0,-1,1
i=75,20,1,0,1
i=76,12,1,1,1
i=78,40,0,-1,1
fe:0
ge:4
opti:0
lan:4
pots:1
usb:2
wifi:2
ups:0
catv:0
uart:1
moca:0
e1:0
xge:0
bob:1
sim:0
enet:4
eth_emac:0,eth_mode:1,eth_rate:0,eth_nego:1,eth_cmode:1,eth_port:0
eth_emac:0,eth_mode:1,eth_rate:0,eth_nego:1,eth_cmode:1,eth_port:1
eth_emac:0,eth_mode:1,eth_rate:0,eth_nego:1,eth_cmode:1,eth_port:2
eth_emac:0,eth_mode:1,eth_rate:0,eth_nego:1,eth_cmode:1,eth_port:3
optscheme:6,vendor=GN25L95
gpio:15, value=0
zxic_gpio_init: pull up GPIO_18
gpio:18, value=1
zxic_gpio_init: pull up GPIO_21
gpio:21, value=1
gpio:20, value=0
gpio:12, value=1
gpio:40, value=1
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
zte_gpio 94407000.gpio: ZX GPIO chip registered
Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
synopsys pcie probe enter!!!!!!
pcie0 irq is 56
pcie1 irq is 57
pcie1 link down irq is 58
pcie1 link down irq is 59
Add synopsys PCIe port 0
SYNOPSYS pcie port0 memory addr(PA): 0x10000000
SYNOPSYS pcie port0 system control addr(VA): 0xf0500000
SYNOPSYS pcie port0 reg addr(VA): 0xc8a08000
SYNOPSYS pcie port0 top crm addr(VA): 0xf0400000
SYNOPSYS pcie port0 phy apb addr(VA): 0xc8a10000
SYNOPSYS pcie port0 cfg  addr(VA): 0xc8a20000
SYNOPSYS pcie port0 local irq num: 56
SYNOPSYS pcie port0 mem_offset: 0x0
Add synopsys PCIe port 1
SYNOPSYS pcie port1 memory addr(PA): 0x20000000
SYNOPSYS pcie port1 system control addr(VA): 0xf0500000
SYNOPSYS pcie port1 reg addr(VA): 0xc8a18000
SYNOPSYS pcie port1 top crm addr(VA): 0xf0400000
SYNOPSYS pcie port1 phy apb addr(VA): 0xc8a38000
SYNOPSYS pcie port1 cfg  addr(VA): 0xc8a40000
SYNOPSYS pcie port1 local irq num: 57
SYNOPSYS pcie port1 mem_offset: 0x0
init synopsys pcie
synopsys pcie driver preinit
synopsys pcie  PreInit Controller 0
synopsys pcie0 controller setting
pinmux va base is 0xf0600000
*0****pcie0 wifi reset pin(52)=0
*1****pcie1 wifi reset pin(54)=0
synopsys pcie  PreInit Controller 1
synopsys pcie1 controller setting
pinmux va base is 0xf0600000
Set_Trap_Pkt_Pps_Limit is NULL.
*0****pcie0 wifi reset pin(52)=1
*1****pcie1 wifi reset pin(54)=0
synopsys pcie0 controller waitting L0 state
pcie0 link up,cnt 1!
synopsys pcie port0 irqs setting
pcie0 irq is 56
pcie0 link down irq is 58
synopsys pcie port0 windows map setting
synopsys pcie controller0 enable
synopsys pcie1 controller waitting L0 state
pcie1 link up,cnt 1!
synopsys pcie port1 irqs setting
pcie1 irq is 57
pcie1 link down irq is 59
synopsys pcie port1 windows map setting
synopsys pcie controller1 enable
**********synopsys PCIe Setup*********
synopsys pcie port0 controller root bus: 0
**********synopsys PCI driver ScanBus************
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
**********synopsys PCIe Setup*********
synopsys pcie port1 controller root bus: 1
**********synopsys PCI driver ScanBus************
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x20000000-0x27ffffff]
pci_bus 0000:01: root bus resource [io  0x10000-0x1ffff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
PCI: bus1: Fast back to back transfers disabled
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x100fffff 64bit pref]
pci 0000:00:00.0: BAR 2: assigned [mem 0x10100000-0x10103fff 64bit pref]
pci 0000:00:00.0: BAR 4: assigned [mem 0x10104000-0x10104fff 64bit pref]
zte_leds_dev_init
zte_gpio_key_dev_init
zte_gpio_wdt_dev_init
zte_pps_dev_init
tdm registered!
zx_tdm2.0_probe!
g_tdm_buf =c8a31000,45830000
remap tdm reg 9a106000 to f0806000
tdm irq=27
reg 0xf0800024 value is 0xb83f
tdm binding cpu1....
futex hash table entries: 512 (order: 2, 16384 bytes)
ntfs: driver 2.1.32 [Flags: R/W].
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.23)
io scheduler noop registered (default)
SCSI Media Changer driver v0.25 
no nand flash attach
denali-nand-dt: probe of d80000.nand failed with error -1
zte_spifc_reg:c6016b9c
spifc->io_base :f0706000
is_two_plane: 4
nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
nand: GLGADEVICE SPI NAND GD5F1GQ4UBYIG  128MiB 3,3V
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
Specmaf_id:c8,Specdev_id:d1
NAND Chip: oobsize:0x80, pagesize:0x800, blocksize:0x20000, chipsize:0x8000000, ECC capbility is 8 bits, CRC protection is disabled is_two_plane[4]
Scanning device for bad blocks
Bad eraseblock 328 at 0x000002900000
Bad eraseblock 1023 at 0x000007fe0000
Creating 15 MTD partitions on "ZX279127-ZX279131-spifc":
0x000000000000-0x000008000000 : "whole flash"
0x000000000000-0x000000200000 : "u-boot"
0x000000200000-0x000000400000 : "parameter tags"
0x000000400000-0x000000900000 : "kernel0"
0x000000900000-0x000002900000 : "rootfs0"
0x000002900000-0x000002d00000 : "usercfg"
0x000002d00000-0x000002e00000 : "others"
0x000002e00000-0x000003000000 : "wlan"
0x000003000000-0x000003080000 : "mac"
0x000003080000-0x000003140000 : "fota-flag"
0x000003140000-0x000003d00000 : "cfg-param"
0x000003d00000-0x000004200000 : "log"
0x000004200000-0x000004a00000 : "web"
0x000004a00000-0x000005000000 : "data"
0x000005000000-0x000008000000 : "fota"
zx_spi_probe...master->bus_num:0
SPI0 probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver asix

usb 2-1: New USB device found, idVendor=19d2, idProduct=1489
usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[si_lan_eth_filter_start 93] start.
usb 2-1: Product: ZTE
usb 2-1: Manufacturer: ZTE
usb 2-1: SerialNumber: 123456789ABCD