w tej wersji na totolinku X5000R nie ma wifi, brak sekcji w config oraz brak reakcji na "wifi".
[ 0.000000] Linux version 5.15.120 (cezary@eko.one.pl) (mipsel-openwrt-linux- musl-gcc (OpenWrt GCC 12.3.0 r23004-7f0db09513) 12.3.0, GNU ld (GNU Binutils) 2. 40.0) #0 SMP Thu Jul 27 11:54:55 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is TOTOLINK X5000R
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 11 pages/cpu s14736 r8192 d22128 u45056
[ 0.000000] pcpu-alloc: s14736 r8192 d22128 u45056 alloc=11*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,j ffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, l inear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, lin ear)
[ 0.000000] Writing ErrCtl register=0003034c
[ 0.000000] Readback ErrCtl register=0003034c
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 246628K/262144K available (7292K kernel code, 623K rwdata , 880K rodata, 3736K init, 226K bss, 15516K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478ab b4, max_idle_ns: 440795247997 ns
[ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 43980 46511103ns
[ 0.008042] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.066221] pid_max: default: 32768 minimum: 301
[ 0.071683] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linea r)
[ 0.078895] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.090515] rcu: Hierarchical SRCU implementation.
[ 0.095993] smp: Bringing up secondary CPUs ...
[ 0.101447] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.101473] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.101487] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.101532] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.160772] Synchronize counters for CPU 1: done.
[ 0.193311] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.193332] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.193344] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.193372] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.252275] Synchronize counters for CPU 2: done.
[ 0.282911] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.282932] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.282943] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.282975] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.337461] Synchronize counters for CPU 3: done.
[ 0.367320] smp: Brought up 1 node, 4 CPUs
[ 0.376471] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.386273] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.393377] pinctrl core: initialized pinctrl subsystem
[ 0.400209] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.406825] thermal_sys: Registered thermal governor 'step_wise'
[ 0.412818] FPU Affinity set after 11720 emulations
[ 0.431519] clocksource: Switched to clocksource GIC
[ 0.437801] NET: Registered PF_INET protocol family
[ 0.442911] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear )
[ 0.451087] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.459399] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.467071] TCP established hash table entries: 2048 (order: 1, 8192 bytes, l inear)
[ 0.474718] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.481846] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.488290] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.494795] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.502126] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.507734] PCI: CLS 0 bytes, default 32
[ 0.523290] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.538050] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.543957] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.555578] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 51)
[ 1.010995] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.017130] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.023362] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.029592] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 1.036374] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000 , using [bus 00-ff]
[ 1.045271] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000
[ 1.053477] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.421533] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.428435] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.433314] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.438132] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.445472] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.451794] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.457235] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.464128] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.470312] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.476332] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.482623] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.488933] pci 0000:00:00.0: supports D1
[ 1.492922] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.499713] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.505812] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.512103] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 1.518436] pci 0000:00:01.0: supports D1
[ 1.522467] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.530632] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), rec onfiguring
[ 1.538657] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), rec onfiguring
[ 1.546957] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 1.552962] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref ]
[ 1.560116] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref ]
[ 1.567317] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref ]
[ 1.574625] pci 0000:01:00.0: supports D1 D2
[ 1.578811] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.585454] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.602341] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.607503] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.613580] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.620285] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref ]
[ 1.627486] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.634406] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 1.640364] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref ]
[ 1.647566] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref ]
[ 1.654743] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref ]
[ 1.662041] pci 0000:02:00.0: supports D1 D2
[ 1.666226] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.672861] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.689709] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.694932] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.700940] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 1.707712] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref ]
[ 1.714882] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.721504] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.728028] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.734972] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.741531] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.748423] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.755203] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref ]
[ 1.762369] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 1.769076] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref ]
[ 1.776276] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 1.783030] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 1.789733] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff]
[ 1.795810] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff]
[ 1.801868] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bi t pref]
[ 1.809534] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bi t pref]
[ 1.817267] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bi t pref]
[ 1.824965] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.829844] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.835922] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.842660] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref ]
[ 1.849814] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bi t pref]
[ 1.857537] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bi t pref]
[ 1.865230] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bi t pref]
[ 1.872937] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.877815] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 1.883897] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 1.890602] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref ]
[ 1.900058] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 1.910295] printk: console [ttyS0] disabled
[ 1.914686] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 1.923711] printk: console [ttyS0] enabled
[ 1.932009] printk: bootconsole [early0] disabled
[ 2.183070] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 2.189940] spi-nor spi0.0: en25qh128 (16384 Kbytes)
[ 2.195185] 4 fixed-partitions partitions found on MTD device spi0.0
[ 2.201664] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitio ns
[ 2.209013] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitio ns
[ 2.216980] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitio ns
[ 2.224397] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitio ns
[ 2.232022] Creating 4 MTD partitions on "spi0.0":
[ 2.236827] 0x000000000000-0x000000030000 : "u-boot"
[ 2.242955] 0x000000030000-0x000000040000 : "u-boot-env"
[ 2.249174] 0x000000040000-0x000000050000 : "factory"
[ 2.255331] 0x000000050000-0x000001000000 : "firmware"
[ 2.394550] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.433750] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe 100000, irq 21
[ 4.445956] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe1 00000, irq 21
[ 4.455752] i2c_dev: i2c /dev entries driver
[ 4.462630] NET: Registered PF_INET6 protocol family
[ 4.471278] Segment Routing with IPv6
[ 4.475126] In-situ OAM (IOAM) with IPv6
[ 4.479136] NET: Registered PF_PACKET protocol family
[ 4.484403] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 4.497960] 8021q: 802.1Q VLAN Support v1.8
[ 4.508290] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 4.583419] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 4.591127] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control r x/tx
[ 4.592341] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:00] d river [MediaTek MT7530 PHY] (irq=23)
[ 4.611775] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] d river [MediaTek MT7530 PHY] (irq=24)
[ 4.624823] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] d river [MediaTek MT7530 PHY] (irq=25)
[ 4.637835] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:03] d river [MediaTek MT7530 PHY] (irq=26)
[ 4.650444] DSA: tree 0 setup
[ 4.668354] Freeing unused kernel image (initmem) memory: 3736K
[ 4.674389] This architecture does not have kernel memory protection.
[ 4.680822] Run /init as init process
[ 4.684535] with arguments:
[ 4.684548] /init
[ 4.684556] with environment:
[ 4.684564] HOME=/
[ 4.684572] TERM=linux
[ 5.060196] init: Console is alive
[ 5.064742] init: - watchdog -
[ 5.078598] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.093306] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 5.109445] init: - preinit -
[ 5.306353] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.384787] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.424141] random: jshn: uninitialized urandom read (4 bytes read)
[ 5.699537] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii l ink mode
[ 5.712390] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flo w control rx/tx
[ 5.721182] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 5.729004] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.867672] procd: - early -
[ 7.870788] procd: - watchdog -
[ 8.429432] procd: - watchdog -
[ 8.433068] procd: - ubus -
[ 8.443387] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.486879] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.493817] random: ubusd: uninitialized urandom read (4 bytes read)
[ 8.503881] procd: - init -
[ 8.849590] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.908954] PPP generic driver version 2.4.2
[ 8.915068] NET: Registered PF_PPPOX protocol family
[ 8.927684] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 9.061520] urngd: v1.0.2 started.
[ 9.236167] random: crng init done
[ 9.239564] random: 31 urandom warning(s) missed due to ratelimiting
[ 56.858556] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 56.887428] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii l ink mode
[ 56.895740] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flo w control rx/tx
[ 56.908711] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 56.918428] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 56.926993] br-lan: port 1(lan1) entered blocking state
[ 56.932438] br-lan: port 1(lan1) entered disabled state
[ 56.940288] device lan1 entered promiscuous mode
[ 56.945098] device eth0 entered promiscuous mode
[ 56.982331] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 56.991015] br-lan: port 2(lan2) entered blocking state
[ 56.996551] br-lan: port 2(lan2) entered disabled state
[ 57.003956] device lan2 entered promiscuous mode
[ 57.020949] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 57.029712] br-lan: port 3(lan3) entered blocking state
[ 57.035072] br-lan: port 3(lan3) entered disabled state
[ 57.042694] device lan3 entered promiscuous mode
[ 57.057163] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 57.065591] br-lan: port 4(lan4) entered blocking state
[ 57.070839] br-lan: port 4(lan4) entered disabled state
[ 57.078597] device lan4 entered promiscuous mode
[ 57.110742] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:04] driver [Medi aTek MT7530 PHY] (irq=POLL)
[ 57.120410] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode
[ 59.823252] mt7530-mdio mdio-bus:1f lan4: Link is Up - 1Gbps/Full - flow cont rol off
[ 59.831056] br-lan: port 4(lan4) entered blocking state
[ 59.836330] br-lan: port 4(lan4) entered forwarding state
[ 59.843385] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 60.271735] mtk_soc_eth 1e100000.ethernet wan: Link is Up - 1Gbps/Full - flow control rx/tx
[ 60.280130] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
