enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Operation terminated
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Operation terminated
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 2
0
raspi_read: from:40028 len:6
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.0.111) ==:192.168.0.111
Input server IP (192.168.0.233) ==:192.168.0.10
Input Linux Kernel filename (root_uImage) ==:nexx.bin
netboot_common, argc= 3
NetTxPacket = 0x83FE4C80
KSEG1ADDR(NetTxPacket) = 0xA3FE4C80
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 192.168.0.10; our IP address is 192.168.0.111
Filename 'nexx.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (4c:cc:6a:bd:09:2b)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####
done
Bytes transferred = 7340865 (700341 hex)
NetBootFileXferSize= 00700341
raspi_erase_write: offs:50000, count:700341
raspi_erase: offs:50000 len:700000
................................................................................ ................................
raspi_write: to:50000 len:700000
................................................................................ ................................
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
raspi_read: from:70000 len:10000
raspi_read: from:80000 len:10000
raspi_read: from:90000 len:10000
raspi_read: from:a0000 len:10000
raspi_read: from:b0000 len:10000
raspi_read: from:c0000 len:10000
raspi_read: from:d0000 len:10000
raspi_read: from:e0000 len:10000
raspi_read: from:f0000 len:10000
raspi_read: from:100000 len:10000
raspi_read: from:110000 len:10000
raspi_read: from:120000 len:10000
raspi_read: from:130000 len:10000
raspi_read: from:140000 len:10000
raspi_read: from:150000 len:10000
raspi_read: from:160000 len:10000
raspi_read: from:170000 len:10000
raspi_read: from:180000 len:10000
raspi_read: from:190000 len:10000
raspi_read: from:1a0000 len:10000
raspi_read: from:1b0000 len:10000
raspi_read: from:1c0000 len:10000
raspi_read: from:1d0000 len:10000
raspi_read: from:1e0000 len:10000
raspi_read: from:1f0000 len:10000
raspi_read: from:200000 len:10000
raspi_read: from:210000 len:10000
raspi_read: from:220000 len:10000
raspi_read: from:230000 len:10000
raspi_read: from:240000 len:10000
raspi_read: from:250000 len:10000
raspi_read: from:260000 len:10000
raspi_read: from:270000 len:10000
raspi_read: from:280000 len:10000
raspi_read: from:290000 len:10000
raspi_read: from:2a0000 len:10000
raspi_read: from:2b0000 len:10000
raspi_read: from:2c0000 len:10000
raspi_read: from:2d0000 len:10000
raspi_read: from:2e0000 len:10000
raspi_read: from:2f0000 len:10000
raspi_read: from:300000 len:10000
raspi_read: from:310000 len:10000
raspi_read: from:320000 len:10000
raspi_read: from:330000 len:10000
raspi_read: from:340000 len:10000
raspi_read: from:350000 len:10000
raspi_read: from:360000 len:10000
raspi_read: from:370000 len:10000
raspi_read: from:380000 len:10000
raspi_read: from:390000 len:10000
raspi_read: from:3a0000 len:10000
raspi_read: from:3b0000 len:10000
raspi_read: from:3c0000 len:10000
raspi_read: from:3d0000 len:10000
raspi_read: from:3e0000 len:10000
raspi_read: from:3f0000 len:10000
raspi_read: from:400000 len:10000
raspi_read: from:410000 len:10000
raspi_read: from:420000 len:10000
raspi_read: from:430000 len:10000
raspi_read: from:440000 len:10000
raspi_read: from:450000 len:10000
raspi_read: from:460000 len:10000
raspi_read: from:470000 len:10000
raspi_read: from:480000 len:10000
raspi_read: from:490000 len:10000
raspi_read: from:4a0000 len:10000
raspi_read: from:4b0000 len:10000
raspi_read: from:4c0000 len:10000
raspi_read: from:4d0000 len:10000
raspi_read: from:4e0000 len:10000
raspi_read: from:4f0000 len:10000
raspi_read: from:500000 len:10000
raspi_read: from:510000 len:10000
raspi_read: from:520000 len:10000
raspi_read: from:530000 len:10000
raspi_read: from:540000 len:10000
raspi_read: from:550000 len:10000
raspi_read: from:560000 len:10000
raspi_read: from:570000 len:10000
raspi_read: from:580000 len:10000
raspi_read: from:590000 len:10000
raspi_read: from:5a0000 len:10000
raspi_read: from:5b0000 len:10000
raspi_read: from:5c0000 len:10000
raspi_read: from:5d0000 len:10000
raspi_read: from:5e0000 len:10000
raspi_read: from:5f0000 len:10000
raspi_read: from:600000 len:10000
raspi_read: from:610000 len:10000
raspi_read: from:620000 len:10000
raspi_read: from:630000 len:10000
raspi_read: from:640000 len:10000
raspi_read: from:650000 len:10000
raspi_read: from:660000 len:10000
raspi_read: from:670000 len:10000
raspi_read: from:680000 len:10000
raspi_read: from:690000 len:10000
raspi_read: from:6a0000 len:10000
raspi_read: from:6b0000 len:10000
raspi_read: from:6c0000 len:10000
raspi_read: from:6d0000 len:10000
raspi_read: from:6e0000 len:10000
raspi_read: from:6f0000 len:10000
raspi_read: from:700000 len:10000
raspi_read: from:710000 len:10000
raspi_read: from:720000 len:10000
raspi_read: from:730000 len:10000
raspi_read: from:740000 len:10000
raspi_read: from:750000 len:10000
raspi_erase: offs:750000 len:10000
.
raspi_write: to:750000 len:10000
.
raspi_read: from:750000 len:10000
Done!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-5.4.171
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1992274 Bytes = 1.9 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1e6652
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 5.4.171 (cezary@eko.one.pl) (gcc version 8.4.0 (Ope nWrt GCC 8.4.0 r15819-0011c7ad12)) #0 Sat Jan 15 21:49:28 2022
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Nexx WT3020 (8M)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, lin ear)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, line ar)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 57508K/65536K available (5068K kernel code, 208K rwdata, 632K rodata, 1188K init, 213K bss, 8028K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from 0x805c7a28 with crng_init=0
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015499] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.059585] pid_max: default: 32768 minimum: 301
[ 0.068975] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linea r)
[ 0.083390] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.104544] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns
[ 0.123842] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[ 0.137433] pinctrl core: initialized pinctrl subsystem
[ 0.149245] NET: Registered protocol family 16
[ 0.186550] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.197591] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.210181] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.221017] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.238738] clocksource: Switched to clocksource systick
[ 0.250332] thermal_sys: Registered thermal governor 'step_wise'
[ 0.250825] NET: Registered protocol family 2
[ 0.271498] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear )
[ 0.286667] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.303233] TCP established hash table entries: 1024 (order: 0, 4096 bytes, l inear)
[ 0.318402] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.332413] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.345193] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.358102] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.372194] NET: Registered protocol family 1
[ 0.380774] PCI: CLS 0 bytes, default 32
[ 0.391675] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.405834] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.427271] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.438775] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.474514] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 52)
[ 0.492244] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.507833] printk: console [ttyS0] disabled
[ 0.516300] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.535944] printk: console [ttyS0] enabled
[ 0.535944] printk: console [ttyS0] enabled
[ 0.552529] printk: bootconsole [early0] disabled
[ 0.552529] printk: bootconsole [early0] disabled
[ 0.580917] spi spi0.0: force spi mode3
[ 0.598496] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[ 0.608286] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.620947] Creating 4 MTD partitions on "spi0.0":
[ 0.630505] 0x000000000000-0x000000030000 : "u-boot"
[ 0.641543] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.653330] 0x000000040000-0x000000050000 : "factory"
[ 0.664548] 0x000000050000-0x000000800000 : "firmware"
[ 0.680085] 2 uimage-fw partitions found on MTD device firmware
[ 0.691948] Creating 2 MTD partitions on "firmware":
[ 0.701862] 0x000000000000-0x0000001e6692 : "kernel"
[ 0.712913] 0x0000001e6692-0x0000007b0000 : "rootfs"
[ 0.723908] mtd: device 5 (rootfs) set to be root filesystem
[ 0.737459] 1 squashfs-split partitions found on MTD device rootfs
[ 0.749863] 0x0000006d7000-0x0000007b0000 : "rootfs_data"
[ 0.762686] libphy: Fixed MDIO Bus: probed
[ 0.780992] gsw: setting port4 to ephy mode
[ 0.789426] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link u p (100Mbps/Full duplex)
[ 0.808140] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.820708] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 0.837728] rt2880_wdt 10000120.watchdog: Initialized
[ 0.849502] NET: Registered protocol family 10
[ 0.863136] Segment Routing with IPv6
[ 0.870641] NET: Registered protocol family 17
[ 0.879585] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.905429] 8021q: 802.1Q VLAN Support v1.8
[ 0.925946] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.946770] Freeing unused kernel memory: 1188K
[ 0.955805] This architecture does not have kernel memory protection.
[ 0.968640] Run /sbin/init as init process
[ 1.546687] random: fast init done
[ 2.636550] init: Console is alive
[ 2.643718] init: - watchdog -
[ 7.290053] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.458398] usbcore: registered new interface driver usbfs
[ 7.469522] usbcore: registered new interface driver hub
[ 7.480234] usbcore: registered new device driver usb
[ 7.548422] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.571197] SCSI subsystem initialized
[ 7.584577] ehci-fsl: Freescale EHCI Host controller driver
[ 7.597943] ehci-platform: EHCI generic platform driver
[ 7.618770] phy phy-usbphy.0: remote usb device wakeup disabled
[ 7.630581] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 7.639445] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 7.650934] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 7.666855] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 7.684498] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 7.698039] hub 1-0:1.0: USB hub found
[ 7.706016] hub 1-0:1.0: 1 port detected
[ 7.719733] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.733969] ohci-platform: OHCI generic platform driver
[ 7.744782] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 7.758383] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 7.774303] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 7.811443] hub 2-0:1.0: USB hub found
[ 7.819418] hub 2-0:1.0: 1 port detected
[ 7.836146] usbcore: registered new interface driver usb-storage
[ 7.850898] usbcore: registered new interface driver uas
[ 7.862527] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 7.881214] init: - preinit -
[ 9.901787] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.000546] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.233737] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.966544] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug[ 11.048 497] urandom_read: 4 callbacks suppressed
level
[ 11.048506] random: procd: uninitialized urandom read (4 bytes read)
[ 12.595625] mount_root: loading kmods from internal overlay
[ 12.668005] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.683788] kmodloader: done loading kernel modules from //etc/modules-boot.d /*
[ 14.480838] block: attempting to load /etc/config/fstab
[ 14.496976] block: unable to load configuration (fstab: Entry not found)
[ 14.510506] block: no usable configuration
[ 14.519773] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 14.541298] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 14.819552] procd: - early -
[ 14.825572] procd: - watchdog -
[ 15.385770] random: jshn: uninitialized urandom read (4 bytes read)
Failed to connect to ubus
[ 15.555412] procd: - watchdog -
[ 15.571248] procd: - ubus -
[ 15.865057] random: jshn: uninitialized urandom read (4 bytes read)
[ 15.902590] procd: - init -
Please press Enter to activate this console.
[ 18.277340] kmodloader: loading kernel modules from /etc/modules.d/*
[ 18.666821] urngd: jent-rng init failed, err: 2
[ 18.795734] fuse: init (API version 7.31)
[ 18.839355] usbcore: registered new interface driver cdc_acm
[ 18.850687] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters
[ 18.892636] usbcore: registered new interface driver cdc_wdm
[ 18.926582] Loading modules backported from Linux version v5.10.85-0-ge4f2aee 6612e
[ 18.941743] Backport generated by backports.git v5.10.85-1-0-gf988973f
[ 19.033196] usbcore: registered new interface driver usblp
[ 19.077353] usbcore: registered new interface driver usbserial_generic
[ 19.090548] usbserial: USB Serial support registered for generic
[ 19.148518] xt_time: kernel timezone is -0000
[ 19.168863] usbcore: registered new interface driver cdc_ether
[ 19.198217] usbcore: registered new interface driver cdc_ncm
[ 19.283015] usbcore: registered new interface driver huawei_cdc_ncm
[ 19.534843] PPP generic driver version 2.4.2
[ 19.558503] NET: Registered protocol family 24
[ 19.581887] usbcore: registered new interface driver qmi_wwan
[ 19.613714] usbcore: registered new interface driver rndis_host
[ 19.666107] usbcore: registered new interface driver sierra
[ 19.677394] usbserial: USB Serial support registered for Sierra USB modem
[ 19.725362] usbcore: registered new interface driver sierra_net
[ 19.764653] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for info rmation.
[ 19.780335] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c 4.com>. All Rights Reserved.
[ 19.893838] usbcore: registered new interface driver cdc_mbim
[ 19.910679] usbcore: registered new interface driver option
[ 19.921959] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.956281] usbcore: registered new interface driver qcserial
[ 19.967908] usbserial: USB Serial support registered for Qualcomm USB modem
[ 20.042937] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory "
[ 20.057370] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 d etected
[ 20.072847] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 20.135237] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 33.186205] random: crng init done
[ 74.327143] 8021q: adding VLAN 0 to HW filter on device eth0
[ 74.363043] br-lan: port 1(eth0.1) entered blocking state
[ 74.373893] br-lan: port 1(eth0.1) entered disabled state
[ 74.385026] device eth0.1 entered promiscuous mode
[ 74.394623] device eth0 entered promiscuous mode
[ 74.475451] br-lan: port 1(eth0.1) entered blocking state
[ 74.486290] br-lan: port 1(eth0.1) entered forwarding state
[ 75.322652] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 86.416651] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 86.449711] jffs2_build_filesystem(): unlocking the mtd device...
[ 86.449771] done.
[ 86.465978] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 94.124207] done.
[ 94.143003] jffs2: notice: (3169) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 94.488765] overlayfs: upper fs does not support tmpfile.