1 Temat przez zbynex (edytowany przez zbynex 2020-08-07 10:26:29)

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Temat: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Witam

Jak w temacie ubiłem 2 szt NEXX WT3020 z 16M po aktualizacji firmware plikiem gargoyle-1.13.0.0pre6-ramips-mt7620-wt3020-16M-squashfs-sysupgrade.bin. Aktualizacja w obu przypadkach przebiegła do samego końca poprawnie i po restarcie nie wstał. Regularnie cyklicznie wolno miga dioda led. Po podłączeniu kabla lan do PC łączy i rozłącza lan i tak w kółko. Aktualizacja z wcześniejszej wersji gargoyle od Cezarego.

Wracając do tematu jak najszybciej i jakim firmware postawić router najlepiej przez bootloader ?

Ostatecznie mam zgrane flashe ale nie chcę wyciągać flasha.

Z tego co pamiętam można go postawić bootloaderem i serwerem tftp jednak dawno już się tym nie zajmowałem więc proszę o jakąś podpowiedź przedewszystkim jaki adres tftp i nazwa pliku firmware jaki będzie chciał pobrać.

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

A miałeś faktycznie wlutowane 16MB flash?

Dowolnym - np. tftp64 pod windows, atftpd po linuksa.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Tak oczywiście i był poprawnie wykrywany i działał ponad rok. Nigdy nie było żadnych problemów.

Cezary a mógłbyś pokrótce podpowiedzieć jak to po kolei tftp64 zrobić. Jaki adres tftp i nazwa pliku oraz który obraz zamontować.

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Ustawiasz na stałe adres ip na karcie sieciowej, np. 192.168.1.2. Uruchamiasz tftp64, wskazujesz gdzie jest katalog w plikami, wybierasz interfejs który ma wpisane 192.168.1.2 z listy. Wywalasz wszelkie antywirusy, firewalle, nody czy inne rzeczy dzięki którym czujesz się bezpieczny.

Rozbierasz ostrożnie nexxa żeby go nie połamać, podłączasz konsolę szeregową, podłączasz kabel do komputera. Uruchamiasz, podczas startu masz małe menu. Wybierasz 2: Load system code then write to Flash via TFTP. odpowiadasz na pytania podając adres serwera, adres hosta i nazwę pliku który masz na serwerze tftp. Enter, on to pobiera i wgrywa.

Soft - dokładnie ten sam plik który próbowałeś wgrać.

Ale zanim to zaczniesz - połącz konsolę i zobacz dlaczego się nie uruchomił, zobacz co wypisuje na starcie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Jedna zabrałem się od razu. Terminal to wypluł:

U-Boot 1.1.3 (Jan  3 2014 - 09:12:42)

MAX Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  3 2014  Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS OpenWrt Linux-4.14.187
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1572856 Bytes =  1.5 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:17fff8
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.14.187 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10707-75d11f665c)) #0 Fri Jul 10 11:55:54 2020
[    0.000000] Board has DDR1
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Nexx WT3020 (16M)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] random: get_random_bytes called from 0x80487740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00031a79
[    0.000000] Readback ErrCtl register=00031a79
[    0.000000] Memory: 58824K/65536K available (3937K kernel code, 186K rwdata, 504K rodata, 1188K init, 215K bss, 6712K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015471] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087709] pid_max: default: 32768 minimum: 301
[    0.097117] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110147] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.129063] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.148536] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.160717] pinctrl core: initialized pinctrl subsystem
[    0.172280] NET: Registered protocol family 16
[    0.203106] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.214134] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.226694] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.237690] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.250279] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.261102] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.278176] clocksource: Switched to clocksource systick
[    0.289808] NET: Registered protocol family 2
[    0.299352] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.313129] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.325724] TCP: Hash tables configured (established 1024 bind 1024)
[    0.338490] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350014] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.362699] NET: Registered protocol family 1
[    0.373967] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.386645] Crashlog allocated RAM at address 0x3f00000
[    0.398720] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.417383] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.428882] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.458850] io scheduler noop registered
[    0.466492] io scheduler deadline registered (default)
[    0.477605] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.493013] console [ttyS0] disabled
[    0.500068] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.519745] console [ttyS0] enabled
[    0.519745] console [ttyS0] enabled
[    0.533564] bootconsole [early0] disabled
[    0.533564] bootconsole [early0] disabled
[    0.557201] spi spi0.0: force spi mode3
[    0.575680] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.585126] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.597795] Creating 4 MTD partitions on "spi0.0":
[    0.607361] 0x000000000000-0x000000030000 : "u-boot"
[    0.618143] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.629658] 0x000000040000-0x000000050000 : "factory"
[    0.640650] 0x000000050000-0x000001000000 : "firmware"
[    0.652580] libphy: Fixed MDIO Bus: probed
[    0.671159] gsw: setting port4 to ephy mode
[    0.679765] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.692241] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.709369] rt2880_wdt 10000120.watchdog: Initialized
[    0.720814] NET: Registered protocol family 10
[    0.734116] Segment Routing with IPv6
[    0.741592] NET: Registered protocol family 17
[    0.750522] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.776365] 8021q: 802.1Q VLAN Support v1.8
[    0.786210] hctosys: unable to open rtc device (rtc0)
[    0.797616] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    0.812593] Please append a correct "root=" boot option; here are the available partitions:
[    0.829258] 1f00             192 mtdblock0
[    0.829264]  (driver?)
[    0.842294] 1f01              64 mtdblock1
[    0.842300]  (driver?)
[    0.855332] 1f02              64 mtdblock2
[    0.855338]  (driver?)
[    0.868383] 1f03           16064 mtdblock3
[    0.868389]  (driver?)
[    0.881429] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    0.898867] Rebooting in 1 seconds..


U-Boot 1.1.3 (Jan  3 2014 - 09:12:42)

MAX Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  3 2014  Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Nie podzielił automatycznie flasha. Wgraj wersję od 8MB i zobacz co będzie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Coś nie chce mi pobrać przez tftp firmware. Czy na pewno adres serwera ma być 192.168.1.2 a nie 192.168.8.2. Chyba fabrycznie firmware miał adres 192.168.8.1 ?

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Adres ma być taki jak podajesz w bootloaderze. Jaki podasz taki ma być.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

No i niestety wgrywa się ale router nie startuje.

U-Boot 1.1.3 (Jan  3 2014 - 09:12:42)

MAX Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  3 2014  Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 2
                                                                              0
raspi_read: from:40028 len:6


2: System Load Linux Kernel then write to Flash via TFTP.
 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.0.111) ==:192.168.8.1
        Input server IP (192.168.0.233) ==:192.168.8.2
        Input Linux Kernel filename (root_uImage) ==:gargoyle-1.12.0.2-ramips-mt7620-wt3020-8M-squashfs-sysupgrade.bin

 netboot_common, argc= 3

 NetTxPacket = 0x83FE4C80

 KSEG1ADDR(NetTxPacket) = 0xA3FE4C80

 NetLoop,call eth_halt !

 NetLoop,call eth_init !
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done


 ETH_STATE_ACTIVE!!
TFTP from server 192.168.8.2; our IP address is 192.168.8.1
Filename 'gargoyle-1.12.0.2-ramips-mt7620-wt3020-8M-squashfs-sysupgrade.bin'.

 TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (dc:0e:a1:13:e5:07)
Got it
#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ####################################Got ARP REQUEST, return our IP
#############################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #######################################################
done
Bytes transferred = 7602366 (7400be hex)
NetBootFileXferSize= 007400be
raspi_erase_write: offs:50000, count:7400be
Abort: image size larger than 3866624!

## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS OpenWrt Linux-4.14.187
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1572856 Bytes =  1.5 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:17fff8
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.14.187 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10707-75d11f665c)) #0 Fri Jul 10 11:55:54 2020
[    0.000000] Board has DDR1
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Nexx WT3020 (16M)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] random: get_random_bytes called from 0x80487740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00031a39
[    0.000000] Readback ErrCtl register=00031a39
[    0.000000] Memory: 58824K/65536K available (3937K kernel code, 186K rwdata, 504K rodata, 1188K init, 215K bss, 6712K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015471] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087715] pid_max: default: 32768 minimum: 301
[    0.097122] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110152] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.129069] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.148542] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.160722] pinctrl core: initialized pinctrl subsystem
[    0.172286] NET: Registered protocol family 16
[    0.203112] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.214140] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.226700] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.237696] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.250285] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.261107] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.278181] clocksource: Switched to clocksource systick
[    0.289812] NET: Registered protocol family 2
[    0.299356] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.313133] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.325728] TCP: Hash tables configured (established 1024 bind 1024)
[    0.338494] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350018] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.362703] NET: Registered protocol family 1
[    0.373972] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.386650] Crashlog allocated RAM at address 0x3f00000
[    0.398722] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.417386] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.428885] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.458854] io scheduler noop registered
[    0.466495] io scheduler deadline registered (default)
[    0.477608] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.493016] console [ttyS0] disabled
[    0.500071] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.519748] console [ttyS0] enabled
[    0.519748] console [ttyS0] enabled
[    0.533567] bootconsole [early0] disabled
[    0.533567] bootconsole [early0] disabled
[    0.557204] spi spi0.0: force spi mode3
[    0.575732] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.585178] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.597847] Creating 4 MTD partitions on "spi0.0":
[    0.607413] 0x000000000000-0x000000030000 : "u-boot"
[    0.618254] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.629718] 0x000000040000-0x000000050000 : "factory"
[    0.640710] 0x000000050000-0x000001000000 : "firmware"
[    0.652641] libphy: Fixed MDIO Bus: probed
[    0.671222] gsw: setting port4 to ephy mode
[    0.679630] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 4 link up (100Mbps/Full duplex)
[    0.698057] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.710534] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.727661] rt2880_wdt 10000120.watchdog: Initialized
[    0.739155] NET: Registered protocol family 10
[    0.752458] Segment Routing with IPv6
[    0.759933] NET: Registered protocol family 17
[    0.768860] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.794702] 8021q: 802.1Q VLAN Support v1.8
[    0.804545] hctosys: unable to open rtc device (rtc0)
[    0.815951] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    0.830929] Please append a correct "root=" boot option; here are the available partitions:
[    0.847594] 1f00             192 mtdblock0
[    0.847600]  (driver?)
[    0.860649] 1f01              64 mtdblock1
[    0.860655]  (driver?)
[    0.873694] 1f02              64 mtdblock2
[    0.873701]  (driver?)
[    0.886731] 1f03           16064 mtdblock3
[    0.886737]  (driver?)
[    0.899782] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    0.917229] Rebooting in 1 seconds..


U-Boot 1.1.3 (Jan  3 2014 - 09:12:42)

MAX Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  3 2014  Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Nie, nie wgrał ci tego: 

Abort: image size larger than 3866624!

Weź czysty obraz bez luci który jest dość mały i jego wgraj.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

No niestety żaden obraz nie wgrywa sie. Czyste Openwrt 18.06, Openwrt 19.07i Mifi to samo.

U-Boot 1.1.3 (Jan  3 2014 - 09:12:42)

MAX Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  3 2014  Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 2
                                                                              0
raspi_read: from:40028 len:6


2: System Load Linux Kernel then write to Flash via TFTP.
 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
 Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.0.111) ==:192.168.8.1
        Input server IP (192.168.0.233) ==:192.168.8.2
        Input Linux Kernel filename (root_uImage) ==:openwrt-18.06-snapshot-r7911-f65330d27d-ramips-mt7620-wt3020-8M-squashfs-sysupgrade.bin

 netboot_common, argc= 3

 NetTxPacket = 0x83FE4C80

 KSEG1ADDR(NetTxPacket) = 0xA3FE4C80

 NetLoop,call eth_halt !

 NetLoop,call eth_init !
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done


 ETH_STATE_ACTIVE!!
TFTP from server 192.168.8.2; our IP address is 192.168.8.1
Filename 'openwrt-18.06-snapshot-r7911-f65330d27d-ramips-mt7620-wt3020-8M-squashfs-sysupgrade.bin'.

 TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (dc:0e:a1:13:e5:07)
Got it
#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ############################Got ARP REQUEST, return our IP
#####################################
         #################################################################
         ##########################
done
Bytes transferred = 4456638 (4400be hex)
NetBootFileXferSize= 004400be
raspi_erase_write: offs:50000, count:4400be
Abort: image size larger than 3866624!

Masz jakiś pomysł. Może gdzieś, ktoś ma oryginalny firmware ?

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

12 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Moje 15.05 (chaos calmer)  ma 3.6M. Powinno wejść.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

13 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Dzięki Cezary, wystartowały oba.

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

14 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Cezary a w czystym CC jaki jest login i password bo nie mogę się zalogować po SSH ?

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

15 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Telnetem...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

16 Odpowiedź przez zbynex (edytowany przez zbynex 2020-08-07 13:45:10)

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Jak po połączeniu Telnetem teraz wgrać coś z GUI zakładając że firmware mam na  PC ?

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

17 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Ustaw sobie hasło, prześlij firmware po scp do routera i zrób sysupgrade, ew z opcją -F. Tylko nie ten 16M, skompiluję Ci wieczorem nowy.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

18 Odpowiedź przez zbynex (edytowany przez zbynex 2020-08-07 14:47:58)

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Niestety nie mogę taraz z CC 15.05 zaktualizować wyżej bo wywala błąd kasowania bloku flash i robi cegłe.

root@OpenWrt:~# sysupgrade -n /tmp/luci-18.06-snapshot-r7911-f65330d27d-ramips-m
t7620-wt3020-8M-squashfs-sysupgrade.bin
killall: watchdog: no process killed
Sending TERM to remaining processes ... ntpd dnsmasq ubusd askfirst logd netifd
Sending KILL to remaining processes ... askfirst
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...  [e]Failed to erase block
Upgrade completed
Rebooting system...
WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

19 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Tu już ci nie jestem w stanie pomóc, jeżeli nie chce wyczyścić flash. Możesz spróbować w trybie failsafe to zrobić, choć pewnie będzie podobnie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

20 Odpowiedź przez kiko80

  • kiko80
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-07-04
  • Posty: 119

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Programatorem próbuj.

21 Odpowiedź przez zbynex

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Okazało się że problemem kasowania bloku flash było wgranie Openwrt CC dla wersji 4MB. Po wgraniu dla wersji 16M upgrade poszedł w obu urządzeniach bezproblemowo.

Cezary jak będziesz miał chwilę to skompiluj poprawioną wersję gargoyle-1.13.0.0.

Dzięki za pomoc.

WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

22 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Skompilowałem i podmieniłem pliki dla WT3020-16M. Sprawdź.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

23 Odpowiedź przez zbynex (edytowany przez zbynex 2020-08-07 20:15:21)

  • zbynex
  • Użytkownik
  • Nieaktywny
  • Zarejestrowany: 2015-04-19
  • Posty: 292

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Router wstał ale po zalogowaniu w gui u góry ciągle komunikat:

Pamięć flash routera jest zapełniona (zamontowania w trybie tylko do odczytu) lub tymczasowo wykorzystywana jest pamięć RAM. Router nie będzie działać poprawnie lub powróci do stanu poprzedniego po ponownym uruchomieniu. Przywróć domyślną konfigurację lub wgraj nowe oprogramowanie (bez zachowania ustawień).

Przywrócenie domyślnej konfiguracji nie pomaga.

Terminal wypluwa to:

U-Boot 1.1.3 (Jan  3 2014 - 09:12:42)

MAX Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan  3 2014  Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =64 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS OpenWrt Linux-4.14.187
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1573070 Bytes =  1.5 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:1800ce
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 4.14.187 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10707-75d11f665c)) #0 Sun Aug 2 16:16:00 2020
[    0.000000] Board has DDR1
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Nexx WT3020 (16M)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] random: get_random_bytes called from 0x80487740 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00040005
[    0.000000] Readback ErrCtl register=00040005
[    0.000000] Memory: 58824K/65536K available (3937K kernel code, 186K rwdata, 504K rodata, 1188K init, 215K bss, 6712K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015470] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087713] pid_max: default: 32768 minimum: 301
[    0.097119] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110148] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.129088] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.148561] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.160741] pinctrl core: initialized pinctrl subsystem
[    0.172304] NET: Registered protocol family 16
[    0.203114] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.214142] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.226720] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.237717] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.250292] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.261111] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.278193] clocksource: Switched to clocksource systick
[    0.289814] NET: Registered protocol family 2
[    0.299352] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.313130] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.325721] TCP: Hash tables configured (established 1024 bind 1024)
[    0.338492] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350012] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.362693] NET: Registered protocol family 1
[    0.373975] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.386658] Crashlog allocated RAM at address 0x3f00000
[    0.398743] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.417447] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.428947] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.458886] io scheduler noop registered
[    0.466528] io scheduler deadline registered (default)
[    0.477644] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.493023] console [ttyS0] disabled
[    0.500078] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.519755] console [ttyS0] enabled
[    0.519755] console [ttyS0] enabled
[    0.533573] bootconsole [early0] disabled
[    0.533573] bootconsole [early0] disabled
[    0.557226] spi spi0.0: force spi mode3
[    0.575703] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.585144] 4 fixed-partitions partitions found on MTD device spi0.0
[    0.597814] Creating 4 MTD partitions on "spi0.0":
[    0.607381] 0x000000000000-0x000000030000 : "u-boot"
[    0.618169] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.629707] 0x000000040000-0x000000050000 : "factory"
[    0.640680] 0x000000050000-0x000001000000 : "firmware"
[    0.654721] 2 uimage-fw partitions found on MTD device firmware
[    0.666583] Creating 2 MTD partitions on "firmware":
[    0.676498] 0x000000000000-0x00000018010e : "kernel"
[    0.687264] 0x00000018010e-0x000000fb0000 : "rootfs"
[    0.698014] mtd: device 5 (rootfs) set to be root filesystem
[    0.710898] 1 squashfs-split partitions found on MTD device rootfs
[    0.723279] 0x000000776000-0x000000fb0000 : "rootfs_data"
[    0.735725] libphy: Fixed MDIO Bus: probed
[    0.752487] gsw: setting port4 to ephy mode
[    0.761096] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.773579] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.790715] rt2880_wdt 10000120.watchdog: Initialized
[    0.802138] NET: Registered protocol family 10
[    0.815393] Segment Routing with IPv6
[    0.822870] NET: Registered protocol family 17
[    0.831799] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    0.857641] 8021q: 802.1Q VLAN Support v1.8
[    0.867523] hctosys: unable to open rtc device (rtc0)
[    0.890948] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.911520] Freeing unused kernel memory: 1188K
[    0.920575] This architecture does not have kernel memory protection.
[    2.648194] random: fast init done
[    2.659029] init: Console is alive
[    2.666040] init: - watchdog -
[    7.427567] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    7.790138] usbcore: registered new interface driver usbfs
[    7.801235] usbcore: registered new interface driver hub
[    7.811951] usbcore: registered new device driver usb
[    7.853744] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.875730] SCSI subsystem initialized
[    7.888793] ehci-platform: EHCI generic platform driver
[    7.909574] phy phy-usbphy.0: remote usb device wakeup disabled
[    7.921392] phy phy-usbphy.0: UTMI 16bit 30MHz
[    7.930274] ehci-platform 101c0000.ehci: EHCI Host Controller
[    7.941793] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    7.957706] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    7.979937] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    7.993413] hub 1-0:1.0: USB hub found
[    8.001328] hub 1-0:1.0: 1 port detected
[    8.017017] usbcore: registered new interface driver usb-storage
[    8.031731] usbcore: registered new interface driver uas
[    8.043066] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.061625] init: - preinit -
[   10.239326] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[   10.382783] random: procd: uninitialized urandom read (4 bytes read)
] or [4] key and hit [enter] to select the debug level
[   11.634437] mount_root: loading kmods from internal overlay
[   11.725453] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   11.744584] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   14.113063] block: attempting to load /etc/config/fstab
[   14.125774] block: unable to load configuration (fstab: Entry not found)
[   14.139297] block: no usable configuration
[   14.148358] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   14.246524] urandom-seed: Seed file not found (/etc/urandom.seed)
[   14.383220] procd: - early -
[   14.389064] procd: - watchdog -
[   15.183485] procd: - watchdog -
[   15.190186] procd: - ubus -
[   15.484364] random: ubusd: uninitialized urandom read (4 bytes read)
[   15.795776] random: ubusd: uninitialized urandom read (4 bytes read)
[   15.822144] random: ubusd: uninitialized urandom read (4 bytes read)
[   15.848953] procd: - init -
Please press Enter to activate this console.
[   17.619070] kmodloader: loading kernel modules from /etc/modules.d/*
[   18.064356] Key type dns_resolver registered
[   18.190024] RPC: Registered named UNIX socket transport module.
[   18.201883] RPC: Registered udp transport module.
[   18.211267] RPC: Registered tcp transport module.
[   18.220649] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   18.322050] tun: Universal TUN/TAP device driver, 1.6
[   18.343798] urngd: jent-rng init failed, err: 2
[   18.438656] gre: GRE over IPv4 demultiplexor driver
[   18.491373] ip_gre: GRE over IPv4 tunneling driver
[   18.629835] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   18.654803] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   18.700562] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   18.930161] fuse init (API version 7.26)
[   18.969063] usbcore: registered new interface driver cdc_acm
[   18.980420] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   19.031339] usbcore: registered new interface driver cdc_wdm
[   19.057055] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[   19.072380] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[   19.142673] Ebtables v2.0 registered
[   19.161992] ip_tables: (C) 2000-2006 Netfilter Core Team
[   19.588689] usbcore: registered new interface driver ums-alauda
[   19.618239] usbcore: registered new interface driver ums-cypress
[   19.651808] usbcore: registered new interface driver ums-datafab
[   19.678880] usbcore: registered new interface driver ums-freecom
[   19.711803] usbcore: registered new interface driver ums-isd200
[   19.734217] usbcore: registered new interface driver ums-jumpshot
[   19.761579] usbcore: registered new interface driver ums-karma
[   19.792553] usbcore: registered new interface driver ums-sddr09
[   19.821603] usbcore: registered new interface driver ums-sddr55
[   19.852175] usbcore: registered new interface driver ums-usbat
[   19.882859] usbcore: registered new interface driver usblp
[   19.935810] usbcore: registered new interface driver usbserial
[   19.947590] usbcore: registered new interface driver usbserial_generic
[   19.960730] usbserial: USB Serial support registered for generic
[   20.118328] xt_time: kernel timezone is -0000
[   20.135365] usbcore: registered new interface driver cdc_ether
[   20.174682] usbcore: registered new interface driver cdc_ncm
[   20.371249] usbcore: registered new interface driver huawei_cdc_ncm
[   20.591004] PPP generic driver version 2.4.2
[   20.621168] NET: Registered protocol family 24
[   20.641016] PPTP driver version 0.8.5
[   20.663618] usbcore: registered new interface driver qmi_wwan
[   20.688359] usbcore: registered new interface driver rndis_host
[   20.758843] usbcore: registered new interface driver sierra
[   20.770131] usbserial: USB Serial support registered for Sierra USB modem
[   20.809385] usbcore: registered new interface driver sierra_net
[   20.852376] usbcore: registered new interface driver cdc_mbim
[   20.881866] usbcore: registered new interface driver option
[   20.893144] usbserial: USB Serial support registered for GSM modem (1-port)
[   20.940993] usbcore: registered new interface driver qcserial
[   20.952601] usbserial: USB Serial support registered for Qualcomm USB modem
[   21.056861] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[   21.071341] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   21.086804] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   21.146162] kmodloader: done loading kernel modules from /etc/modules.d/*
[   71.652461] 8021q: adding VLAN 0 to HW filter on device eth0
[   71.686562] br-lan: port 1(eth0.1) entered blocking state
[   71.697554] br-lan: port 1(eth0.1) entered disabled state
[   71.708691] device eth0.1 entered promiscuous mode
[   71.718278] device eth0 entered promiscuous mode
[   71.808551] br-lan: port 1(eth0.1) entered blocking state
[   71.819374] br-lan: port 1(eth0.1) entered forwarding state
[   71.830720] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   72.700363] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   78.102869] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[   78.119455] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[   82.916713] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[   82.936201] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[   82.963696] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 1, phase=3b)
[   82.982821] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[   83.010752] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 1, phase=3e)
[   83.029003] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[   83.071492] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=-2
[   83.096862] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=1, Ph_rx=0
[   83.186664] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   83.237219] br-lan: port 2(wlan0) entered blocking state
[   83.247880] br-lan: port 2(wlan0) entered disabled state
[   83.258865] device wlan0 entered promiscuous mode
[   85.149832] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   85.162760] br-lan: port 2(wlan0) entered blocking state
[   85.173397] br-lan: port 2(wlan0) entered forwarding state
[   96.250273] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   96.276221] jffs2_build_filesystem(): unlocking the mtd device...
[   96.279756] done.
[   96.295981] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   96.329724] random: crng init done
[   96.351401] random: 6 urandom warning(s) missed due to ratelimiting
WNDR 4300, WT3020F, TL-WR842NDV2 i MR3420V2 RamMOD FlashMOD U-Boot + Hilink E3372s + RTL2832u + IT9135v02 + HDD + VOIP + Gargoyle PL 1.10.0.1 by Obsy

24 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Za krótko czekałeś. jffs na 16M potrafi się kilka ładnych minut robić.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

25 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,288

Odp: NEXX WT3020 16M cegła po aktualizacji gargoyle-1.13.0.0pre6-ramips-mt7

Tak, włącz i poczekaj.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona