Temat: Xiaomi miwifi 3g - cegła
Hej
Niedziela:
Xiaomi miwifi działał poniżej 3 lat. Obraził sie i przestał.
Firmware openwrt od Cezarego, ostatnia aktualizacja w okolicach kwietnia/maja.
Objawy po dostarczeniu zasilania:
Żółta dioda led
Po dłuższej chwili mrugnięcie niebieską diodą led
Brak migania na portach ethernet po wpięciu drugiego urządzenia sieciowego.
Log z uart:
--------------------------------------
0 | 11 9 9 11 9 8 9 6 8 6
10 | 8 10 8 10 7 9
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0080
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1
DQ loop=14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=12500000 HZ
===================================================================
===================================================================
MT7621 stage1 code 10:33:11 (ASIC)
CPU=50000000 HZ BUS=12500000 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0x7, 1/0 = 591/433 1D000000
PLL2 FB_DL: 0xa, 1/0 = 720/304 29000000
PLL4 FB_DL: 0xe, 1/0 = 694/330 39000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
0 8 16 24 32 40 48 56 64 72 80 88 96 104 11 2 120
-------------------------------------------------------------------------- ------
0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1
000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0
0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0
0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
rank 0 coarse = 15
rank 0 fine = 72
B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0
opt_dle value:11
DRAMC_R0DELDLY[018]=00001E1D
==================================================================
RX DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 10 7 7 9 7 7 8 6 5 5
10 | 7 9 7 10 7 9
--------------------------------------
==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =29 DQS1 = 30
==================================================================
bit DQS0 bit DQS1
0 (1~58)29 8 (0~56)28
1 (1~56)28 9 (1~58)29
2 (1~56)28 10 (1~58)29
3 (1~57)29 11 (2~57)29
4 (1~57)29 12 (1~57)29
5 (1~58)29 13 (1~58)29
6 (1~58)29 14 (1~60)30
7 (1~58)29 15 (1~58)29
==================================================================
3.dq delay value last
==================================================================
bit| 0 1 2 3 4 5 6 7 8 9
--------------------------------------
0 | 10 8 8 9 7 7 8 6 7 6
10 | 8 10 8 11 7 10
==================================================================
==================================================================
TX perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2
DQ loop=15, cmp_err_1 = ffff0080
dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=1
DQ loop=14, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=14, finish count=2
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
20,data:88
[EMI] DRAMC calibration passed
===================================================================
MT7621 stage1 code done
CPU=50000000 HZ BUS=12500000 HZ
===================================================================
U-Boot 1.1.3 (Apr 17 2017 - 17:00:02)
Board: Ralink APSoC DRAM: 256 MB
Power on memory test. Memory size= 256 MB...OK!
relocate_code Pointer at: 8ffac000
Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 8ffdffd0
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [C8 D1 80 95 42]
Device not found, ID: c8d1
Not Support this Device!
chip_mode=00000001
Support this Device in MTK table! c8d1
select_chip
[NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
Signature matched and data read!
load_fact_bbt success 1023
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8
..============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=5 OCP Ratio=1/4
Flash component: NAND Flash
Date:Apr 17 2017 Time:17:00:02
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LWLLL
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
Booting System 2
..Erasing NAND Flash...
ranand_erase: start:80000, len:20000
.Writing to NAND Flash...
done
3: System Boot system code via Flash.
## Booting image at bc600000 ...
Image Name: MIPS OpenWrt Linux-4.14.171
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1873549 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
............................. Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
commandline uart_en=1 factory_mode=0 usb_u3=0
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 4.14.171 (cezary@eko.one.pl) (gcc version 7.5.0 (Op enWrt GCC 7.5.0 r10707-75d11f665c)) #0 SMP Mon Feb 24 13:20:14 2020
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router 3G
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] random: get_random_bytes called from 0x80575744 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26224 r8192 d22928 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,j ffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=0000082b
[ 0.000000] Readback ErrCtl register=0000082b
[ 0.000000] Memory: 252460K/262144K available (4746K kernel code, 241K rwdata , 588K rodata, 1260K init, 255K bss, 9684K reserved, 0K cma-reserved, 0K highmem )
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478ab b4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 4343773742 ns
[ 0.000010] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 48806 45118ns
[ 0.007814] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073981] pid_max: default: 32768 minimum: 301
[ 0.078754] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085263] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094093] Hierarchical SRCU implementation.
[ 0.099254] smp: Bringing up secondary CPUs ...
[ 0.107288] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.107297] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.107309] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.107445] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.164003] Synchronize counters for CPU 1: done.
[ 0.201416] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.201425] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.201432] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.201503] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.255154] Synchronize counters for CPU 2: done.
[ 0.288449] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.288457] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.288464] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.288540] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.340335] Synchronize counters for CPU 3: done.
[ 0.370195] smp: Brought up 1 node, 4 CPUs
[ 0.378082] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.387877] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.394181] pinctrl core: initialized pinctrl subsystem
[ 0.400879] NET: Registered protocol family 16
[ 0.412222] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.717544] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.722588] ***** Xtal 40MHz *****
[ 0.725948] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.731047] Port 0 N_FTS = 1b102800
[ 0.734522] Port 1 N_FTS = 1b102800
[ 0.737955] Port 2 N_FTS = 1b102800
[ 1.893199] PCIE2 no card, disable it(RST&CLK)
[ 1.897561] -> 21007f2
[ 1.899961] PCIE0 enabled
[ 1.902554] PCIE1 enabled
[ 1.905157] PCI host bridge /pcie@1e140000 ranges:
[ 1.909937] MEM 0x0000000060000000..0x000000006fffffff
[ 1.915093] IO 0x000000001e160000..0x000000001e16ffff
[ 1.920289] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 1.936586] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.942421] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.948144] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.955825] PCI host bridge to bus 0000:00
[ 1.959861] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.966700] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.972551] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.979304] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff]
[ 1.987999] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), rec onfiguring
[ 1.995925] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), rec onfiguring
[ 2.005236] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.011772] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.018664] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.025243] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.032139] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.038892] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.045624] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref ]
[ 2.052804] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 2.059535] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 2.066299] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 2.073006] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.077945] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.084684] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bi t]
[ 2.091955] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref ]
[ 2.099099] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.104036] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.110766] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref ]
[ 2.119469] clocksource: Switched to clocksource GIC
[ 2.125816] NET: Registered protocol family 2
[ 2.130975] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.137865] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.144287] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.150706] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.156474] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.162931] NET: Registered protocol family 1
[ 2.399413] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.405809] Crashlog allocated RAM at address 0x3f00000
[ 2.411218] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 2.424870] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.424875] random: fast init done
[ 2.433986] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 2.447325] io scheduler noop registered
[ 2.451264] io scheduler deadline registered (default)
[ 2.457442] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 2.467445] console [ttyS0] disabled
[ 2.471081] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.480142] console [ttyS0] enabled
[ 2.480142] console [ttyS0] enabled
[ 2.487000] bootconsole [early0] disabled
[ 2.487000] bootconsole [early0] disabled
[ 2.497444] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.504609] Enable NFI Clock
[ 2.507483] # MTK NAND # : Use HW ECC
[ 2.511164] Device not found, ID: c8d1
[ 2.514891] Not Support this Device!
[ 2.518616] chip_mode=00000001
[ 2.521686] Support this Device in MTK table! c8d1
[ 2.526635] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.533114] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 2.539465] nand: ESMT NAND 128MiB 3,3V 8-bit
[ 2.543803] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64
[ 2.551367] Scanning device for bad blocks
[ 2.700818] 10 fixed-partitions partitions found on MTD device MT7621-NAND
[ 2.707660] Creating 10 MTD partitions on "MT7621-NAND":
[ 2.712980] 0x000000000000-0x000000080000 : "Bootloader"
[ 2.719401] 0x000000080000-0x0000000c0000 : "Config"
[ 2.725472] 0x0000000c0000-0x000000100000 : "Bdata"
[ 2.731433] 0x000000100000-0x000000140000 : "Factory"
[ 2.737496] 0x000000140000-0x000000180000 : "crash"
[ 2.743492] 0x000000180000-0x0000001c0000 : "crash_syslog"
[ 2.750118] 0x0000001c0000-0x000000200000 : "reserved0"
[ 2.756372] 0x000000200000-0x000000600000 : "kernel_stock"
[ 2.762989] 0x000000600000-0x000000a00000 : "kernel"
[ 2.768988] 0x000000a00000-0x000007f80000 : "ubi"
[ 2.775729] [mtk_nand] probe successfully!
[ 2.780587] Signature matched and data read!
[ 2.784836] load_fact_bbt success 1023
[ 2.789357] libphy: Fixed MDIO Bus: probed
[ 5.046900] random: crng init done
[ 62.799501] INFO: rcu_sched self-detected stall on CPU
[ 62.804629] 0-...: (5999 ticks this GP) idle=892/140000000000002/0 softirq=2 8/28 fqs=2280
[ 62.812935] (t=6000 jiffies g=-287 c=-288 q=306)
[ 62.817710] NMI backtrace for cpu 0
[ 62.821184] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.171 #0
[ 62.827244] Stack : 00000000 00000000 00000000 80550000 00000000 00000000 000 00000 00000000
[ 62.835575] 00000000 00000000 00000000 00000000 00000000 00000001 8fc 09b88 1cc2824b
[ 62.843906] 8fc09c20 00000000 00000000 00003838 00000038 8049ba78 000 00007 00000000
[ 62.852236] 00000000 80550000 000c87c0 00000000 8fc09b68 00000000 000 00000 00000000
[ 62.860567] 80552500 8054a0cc 000000e0 80550000 00000000 802ac920 000 00000 806b0000
[ 62.868898] ...
[ 62.871331] Call Trace:
[ 62.871350] [<8049ba78>] 0x8049ba78
[ 62.877244] [<802ac920>] 0x802ac920
[ 62.880714] [<8000c1a0>] 0x8000c1a0
[ 62.884182] [<8000c1a8>] 0x8000c1a8
[ 62.887650] [<804848f4>] 0x804848f4
[ 62.891118] [<800729e4>] 0x800729e4
[ 62.894587] [<8048b904>] 0x8048b904
[ 62.898053] [<80008f30>] 0x80008f30
[ 62.901523] [<80008f30>] 0x80008f30
[ 62.904990] [<8048b9f0>] 0x8048b9f0
[ 62.908459] [<80086278>] 0x80086278
[ 62.911930] [<800856c8>] 0x800856c8
[ 62.915401] [<80088e3c>] 0x80088e3c
[ 62.918868] [<80099e10>] 0x80099e10
[ 62.922338] [<80099e68>] 0x80099e68
[ 62.925807] [<8025a9c0>] 0x8025a9c0
[ 62.929274] [<80330b74>] 0x80330b74
[ 62.932743] [<80077c04>] 0x80077c04
[ 62.936210] [<80079058>] 0x80079058
[ 62.939679] [<80078000>] 0x80078000
[ 62.943148] [<80073370>] 0x80073370
[ 62.946615] [<8025a7a8>] 0x8025a7a8
[ 62.950083] [<8025a654>] 0x8025a654
[ 62.953551] [<8031db80>] 0x8031db80
[ 62.957018] [<8025a814>] 0x8025a814
[ 62.960486] [<80073370>] 0x80073370
[ 62.963955] [<803186dc>] 0x803186dc
[ 62.967422] [<804a273c>] 0x804a273c
[ 62.970892] [<80259ed0>] 0x80259ed0
[ 62.974362] [<80007488>] 0x80007488
[ 62.977835] [<80032f84>] 0x80032f84
[ 62.981304] [<8025a7a8>] 0x8025a7a8
[ 62.984773] [<804a2814>] 0x804a2814
[ 62.988243] [<80032f84>] 0x80032f84
[ 62.991712] [<80259ed0>] 0x80259ed0
[ 62.995181] [<80007488>] 0x80007488
[ 62.998647]Próba wgrania jądra przy użyciu sftp przez bootloadera:
Timeout, porty sieciowe nie są podniesione
1. Warto coś jeszcze sprawdzić przez konsole?
2. Warto coś sprawdzić na płytce? Bezpiecznik, Ogranicznik prądowy, Często palące sie elementy?