Temat: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log
Witam, mój WDR 3600 czasem łapie jakieś resety, jeszcze niedawno myślałem że to wina zasilania ponieważ brałem go na działkę gdzie czasami (przez solar) mam 14V ,
ale po powrocie do domu resety też są. Postanowiłem podłączyć się przez serial i oto co widać (poniżej)
Dwa razy się zresetował sam, pierwszym razem chyba sie w pełni uruchomił, drugim już nie zdążył a za trzecim razem już sam go wyłączyłem.
Sprzęt WDR3600 USB-Mod Gargoyle 1.12 + gsm ,kamerka ,extroot + dodatkowy pendraiw na zdjęcia z kamerki.
***************************************
* U-Boot 1.1.4-7a540a78-clean *
* Build: 2018-02-23 *
***************************************
** Warning: bad env CRC, using default,
use 'saveenv' to save it in FLASH
BOARD: TP-Link TL-WDR3600 v1
SOC: AR9344 rev. 2
CPU: MIPS 74Kc
RAM: 128 MB DDR2 32-bit CL3-4-4-10
FLASH: 16 MB Winbond W25Q128
PCIe: 168C:0033
MAC: 64:70:02:D1:67:62
CLOCKS: CPU/RAM/AHB/SPI/REF
550/400/200/ 25/ 40 MHz
Hit any key to stop booting: 0
Booting image from 0x9F020000...
Vendor/image name: OpenWrt r7935-d08a63770c
Hardware ID: 0x36000001
Whole image size: 7.8 MB (8126464 bytes)
Kernel size: 1.3 MB (1385806 bytes)
Rootfs size: 5.7 MB (5958384 bytes)
Kernel load address: 0x80060000
Kernel entry point: 0x80060000
Header CRC... skipped
Data CRC... skipped
Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...
[ 0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Wed Dec 11 21:46:13 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns
[ 0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns
[ 0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[ 0.081683] pid_max: default: 32768 minimum: 301
[ 0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105229] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.116238] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.124386] NET: Registered protocol family 16
[ 0.130976] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.140736] registering PCI controller with io_map_base unset
[ 0.396084] PCI host bridge to bus 0000:00
[ 0.400716] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.408380] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.414607] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.422171] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.431060] pci 0000:00:00.0: invalid calibration data
[ 0.437239] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.445439] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.453499] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.462680] clocksource: Switched to clocksource MIPS
[ 0.469511] NET: Registered protocol family 2
[ 0.475414] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.483251] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.490349] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.497536] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.504094] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.511349] NET: Registered protocol family 1
[ 0.519432] Crashlog allocated RAM at address 0x3f00000
[ 0.526536] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.541137] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.547690] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.569078] io scheduler noop registered
[ 0.573505] io scheduler deadline registered (default)
[ 0.579697] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.589736] console [ttyS0] disabled
[ 0.613833] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.623470] console [ttyS0] enabled
[ 0.623470] console [ttyS0] enabled
[ 0.630885] bootconsole [early0] disabled
[ 0.630885] bootconsole [early0] disabled
[ 0.646141] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.660741] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.665895] 5 tp-link partitions found on MTD device spi0.0
[ 0.671551] Creating 5 MTD partitions on "spi0.0":
[ 0.676452] 0x000000000000-0x000000020000 : "u-boot"
[ 0.683642] 0x000000020000-0x000000172750 : "kernel"
[ 0.690872] 0x000000172750-0x000000ff0000 : "rootfs"
[ 0.697722] mtd: device 2 (rootfs) set to be root filesystem
[ 0.703557] 1 squashfs-split partitions found on MTD device rootfs
[ 0.709833] 0x000000730000-0x000000ff0000 : "rootfs_data"
[ 0.717696] 0x000000ff0000-0x000001000000 : "art"
[ 0.724771] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.733373] libphy: Fixed MDIO Bus: probed
[ 0.748880] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 1.415835] libphy: ag71xx_mdio: probed
[ 2.044086] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 2.055653] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.064135] NET: Registered protocol family 10
[ 2.073146] NET: Registered protocol family 17
[ 2.077723] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.091014] 8021q: 802.1Q VLAN Support v1.8
[ 2.097273] hctosys: unable to open rtc device (rtc0)
[ 2.106163] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.115015] Freeing unused kernel memory: 308K
[ 2.119527] This architecture does not have kernel memory protection.
[ 2.562699] random: fast init done
[ 2.791351] init: Console is alive
[ 2.795103] init: - watchdog -
[ 5.115975] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.400632] usbcore: registered new interface driver usbfs
[ 5.406365] usbcore: registered new interface driver hub
[ 5.411871] usbcore: registered new device driver usb
[ 5.455918] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.472451] SCSI subsystem initialized
[ 5.482220] ehci-platform: EHCI generic platform driver
[ 5.487685] ehci-platform ehci-platform: EHCI Host Controller
[ 5.493577] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.503729] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.532777] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.540101] hub 1-0:1.0: USB hub found
[ 5.544375] hub 1-0:1.0: 1 port detected
[ 5.553773] usbcore: registered new interface driver usb-storage
[ 5.569232] usbcore: registered new interface driver uas
[ 5.575514] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.585337] init: - preinit -
[ 6.104103] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.306753] hub 1-1:1.0: USB hub found
[ 6.384317] hub 1-1:1.0: 4 ports detected
[ 6.466738] random: procd: uninitialized urandom read (4 bytes read)
[ 6.764924] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press [ 6.842768] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.566501] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 7.573860] scsi host0: usb-storage 1-1.1:1.0
[ 7.672702] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[ 7.793959] eth0: link up (1000Mbps/Full duplex)
[ 7.798739] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.839542] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 7.846831] scsi host1: usb-storage 1-1.2:1.0
[ 7.952705] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[ 8.222700] usb 1-1.4: new high-speed USB device number 6 using ehci-platform
[ 8.377743] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 8.384905] scsi host2: usb-storage 1-1.4:1.0
[ 8.390208] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[ 8.397966] scsi host3: usb-storage 1-1.4:1.1
[ 8.593985] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ: 0 ANSI: 0 CCS
[ 8.605269] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78 GiB)
[ 8.613769] sd 0:0:0:0: [sda] Write Protect is off
[ 8.619376] sd 0:0:0:0: [sda] No Caching mode page found
[ 8.624827] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.636669] sda: sda1 sda2
[ 8.643634] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 9.394242] scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 9.474241] scsi 3:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 9.503778] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 10.037430] mount_root: loading kmods from internal overlay
[ 10.130170] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.146311] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.105735] jffs2: notice: (535) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 11.121918] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 11.522142] scsi 1:0:0:0: Direct-Access Wilk USB DISK 2.0 PMAP PQ: 0 ANSI: 6
[ 11.550237] sd 1:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.5 GiB)
[ 11.592942] sd 1:0:0:0: [sdc] Write Protect is off
[ 11.599667] sd 1:0:0:0: [sdc] No Caching mode page found
[ 11.605126] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[ 11.691435] sdc: sdc1
[ 11.702421] sd 1:0:0:0: [sdc] Attached SCSI removable disk
/dev/sda1: recovering journal
/dev/sda1: clean, 2932/185840 files, 43382/742784 blocks
[ 12.844558] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 12.951550] mount_root: switched to extroot
[ 12.960420] urandom-seed: Seeding with /etc/urandom.seed
[ 13.137832] eth0: link down
[ 13.154876] procd: - early -
[ 13.157905] procd: - watchdog -
[ 13.819518] procd: - watchdog -
[ 13.823060] procd: - ubus -
[ 14.220196] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.238521] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.249333] random: jshn: uninitialized urandom read (4 bytes read)
[ 14.257399] procd: - init -
Please press Enter to activate this console.
[ 15.754024] usb 1-1.4: USB disconnect, device number 6
[ 15.847617] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.029069] Key type dns_resolver registered
[ 16.063586] RPC: Registered named UNIX socket transport module.
[ 16.069597] RPC: Registered udp transport module.
[ 16.074426] RPC: Registered tcp transport module.
[ 16.079201] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.104152] tun: Universal TUN/TAP device driver, 1.6
[ 16.109285] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.132594] gre: GRE over IPv4 demultiplexor driver
[ 16.140324] ip_gre: GRE over IPv4 tunneling driver
[ 16.185865] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 16.213754] i2c /dev entries driver
[ 16.233467] Linux video capture interface: v2.00
[ 16.271202] u32 classifier
[ 16.274022] input device check on
[ 16.277733] Actions configured
[ 16.284920] Mirror/redirect action on
[ 16.340701] fuse init (API version 7.26)
[ 16.442992] usbcore: registered new interface driver cdc_acm
[ 16.448746] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 16.511548] usbcore: registered new interface driver cdc_wdm
[ 16.527520] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 16.535723] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 16.566905] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[ 16.573526] usbcore: registered new interface driver cpia2
[ 16.619846] Ebtables v2.0 registered
[ 16.655954] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.694673] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 17.339104] usbcore: registered new interface driver ums-alauda
[ 17.365816] usbcore: registered new interface driver ums-cypress
[ 17.375848] usbcore: registered new interface driver ums-datafab
[ 17.385805] usbcore: registered new interface driver ums-freecom
[ 17.403645] usbcore: registered new interface driver ums-isd200
[ 17.424375] usbcore: registered new interface driver ums-jumpshot
[ 17.473402] usbcore: registered new interface driver ums-karma
[ 17.512256] usbcore: registered new interface driver ums-sddr09
[ 17.565861] usbcore: registered new interface driver ums-sddr55
[ 17.629099] usbcore: registered new interface driver ums-usbat
[ 17.678890] usbcore: registered new interface driver usblp
[ 17.801967] usbcore: registered new interface driver usbserial
[ 17.808069] usbcore: registered new interface driver usbserial_generic
[ 17.814848] usbserial: USB Serial support registered for generic
[ 18.003143] xt_time: kernel timezone is -0000
[ 18.026859] usbcore: registered new interface driver cdc_ether
[ 18.059372] usbcore: registered new interface driver cdc_ncm
[ 18.179554] gspca_main: v2.14.0 registered
[ 18.205263] usbcore: registered new interface driver mars
[ 18.225606] usbcore: registered new interface driver mr97310a
[ 18.244481] usbcore: registered new interface driver ov519
[ 18.263908] usbcore: registered new interface driver ov534
[ 18.285835] usbcore: registered new interface driver ov534_9
[ 18.305820] usbcore: registered new interface driver pac207
[ 18.319829] usbcore: registered new interface driver pac7311
[ 18.335899] usbcore: registered new interface driver se401
[ 18.357058] usbcore: registered new interface driver gspca_sn9c20x
[ 18.408671] usbcore: registered new interface driver sonixb
[ 18.438579] usbcore: registered new interface driver sonixj
[ 18.465689] usbcore: registered new interface driver spca500
[ 18.495400] usbcore: registered new interface driver spca501
[ 18.513300] usbcore: registered new interface driver spca506
[ 18.539767] usbcore: registered new interface driver spca508
[ 18.575842] usbcore: registered new interface driver spca561
[ 18.609043] usbcore: registered new interface driver sq905
[ 18.624851] usbcore: registered new interface driver sq905c
[ 18.645885] usbcore: registered new interface driver stk014
[ 18.667486] usbcore: registered new interface driver STV06xx
[ 18.685997] usbcore: registered new interface driver sunplus
[ 18.704783] usbcore: registered new interface driver t613
[ 18.721947] usbcore: registered new interface driver tv8532
[ 18.766438] usbcore: registered new interface driver vc032x
[ 18.827937] usbcore: registered new interface driver gspca_zc3xx
[ 18.894942] usbcore: registered new interface driver huawei_cdc_ncm
[ 19.221338] PPP generic driver version 2.4.2
[ 19.243745] NET: Registered protocol family 24
[ 19.250700] PPTP driver version 0.8.5
[ 19.278901] usbcore: registered new interface driver Philips webcam
[ 19.307431] usbcore: registered new interface driver qmi_wwan
[ 19.328354] usbcore: registered new interface driver rndis_host
[ 19.357665] usbcore: registered new interface driver sierra
[ 19.363500] usbserial: USB Serial support registered for Sierra USB modem
[ 19.383454] usbcore: registered new interface driver sierra_net
[ 19.436890] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[ 19.483829] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.3/1-1.3:1.0/input/input0
[ 19.494735] usbcore: registered new interface driver uvcvideo
[ 19.500566] USB Video Class driver (1.1.1)
[ 19.656702] usbcore: registered new interface driver cdc_mbim
[ 19.685860] usbcore: registered new interface driver conex
[ 19.715767] usbcore: registered new interface driver etoms
[ 19.745898] usbcore: registered new interface driver finepix
[ 19.771932] usbcore: registered new interface driver gspca_gl860
[ 19.796749] usbcore: registered new interface driver jeilinj
[ 19.837349] usbcore: registered new interface driver konica
[ 19.870110] usbcore: registered new interface driver ALi m5602
[ 19.892798] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[ 19.903443] usbcore: registered new interface driver option
[ 19.909265] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.944823] usbcore: registered new interface driver qcserial
[ 19.950797] usbserial: USB Serial support registered for Qualcomm USB modem
[ 20.061888] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 20.068862] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 20.094362] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 20.110466] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 20.163509] option 1-1.4:1.0: GSM modem (1-port) converter detected
[ 20.170213] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[ 20.177909] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[ 20.226361] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platform-1.4, Mobile Broadband Network Device, 02:50:f3:00:00:00
[ 20.239680] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[ 20.293535] option 1-1.4:1.3: GSM modem (1-port) converter detected
[ 20.300236] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[ 20.307827] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[ 20.343460] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 20.363357] option 1-1.4:1.4: GSM modem (1-port) converter detected
[ 20.370049] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[ 20.377643] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[ 20.520741] scsi host2: usb-storage 1-1.4:1.5
[ 20.526075] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[ 20.578877] scsi host3: usb-storage 1-1.4:1.6
[ 21.583621] scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 21.640117] scsi 3:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 21.654533] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 24.962775] random: crng init done
[ 24.966242] random: 6 urandom warning(s) missed due to ratelimiting
[ 33.414634] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 36.298287] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 39.348394] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 41.078285] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 42.736627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 42.748729] br-lan: port 1(eth0.1) entered blocking state
[ 42.754282] br-lan: port 1(eth0.1) entered disabled state
[ 42.760193] device eth0.1 entered promiscuous mode
[ 42.765109] device eth0 entered promiscuous mode
[ 42.772146] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 42.821037] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 43.773161] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 43.794230] eth0: link up (1000Mbps/Full duplex)
[ 43.798992] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 43.906898] br-lan: port 1(eth0.1) entered blocking state
[ 43.912391] br-lan: port 1(eth0.1) entered forwarding state
[ 43.918277] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 44.076749] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 48.874709] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 48.921815] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 48.976508] br-lan: port 2(wlan1) entered blocking state
[ 48.981941] br-lan: port 2(wlan1) entered disabled state
[ 48.987822] device wlan1 entered promiscuous mode
[ 49.137650] br-lan: port 3(wlan0) entered blocking state
[ 49.143116] br-lan: port 3(wlan0) entered disabled state
[ 49.148960] device wlan0 entered promiscuous mode
[ 49.153899] br-lan: port 3(wlan0) entered blocking state
[ 49.159315] br-lan: port 3(wlan0) entered forwarding state
[ 49.643134] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 50.192821] br-lan: port 3(wlan0) entered disabled state
[ 52.792443] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 52.799254] br-lan: port 2(wlan1) entered blocking state
[ 52.804732] br-lan: port 2(wlan1) entered forwarding state
[ 52.967739] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 52.974473] br-lan: port 3(wlan0) entered blocking state
[ 52.979877] br-lan: port 3(wlan0) entered forwarding state
[ 54.732467] 3g-wan: renamed from ppp0
[ 56.923784] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 79.367615] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 81.891546] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 84.151602] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 100.211672] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[ 100.218952] old minutes west=0, new minutes west=-120
[ 127.752069] CPU 0 Unable to handle kernel paging request at virtual address 7
[ 127.762855] Oops[#1]:
[ 127.765166] CPU: 0 PID: 5426 Comm: bw_set Not tainted 4.9.206 #0
[ 127.771260] task: 85a8df50 task.stack: 85a26000
[ 127.775849] $ 0 : 00000000 7fedee14 f3ff9d44 7aba5d40
[ 127.781190] $ 4 : 00000001 00000001 00000001 865be180
[ 127.786523] $ 8 : 0002f72d 0002f72c 865bec80 6d6f6e2f
[ 127.791855] $12 : 00000000 0a886034 00000007 00000000
[ 127.797188] $16 : 863a8100 86bac000 865beb80 f3ff9d40
[ 127.802521] $20 : 5e87ce00 00000000 5e891f80 5e7ff388
[ 127.807854] $24 : 00000002 80313760
[ 127.813187] $28 : 85a26000 85a27e20 5e88eb00 87733da4
[ 127.818520] Hi : 00000000
[ 127.821442] Lo : 000047b4
[ 127.824465] epc : 87733d00 0x87733d00 [ipt_bandwidth@87730000+0x45a0]
[ 127.831242] ra : 87733da4 0x87733da4 [ipt_bandwidth@87730000+0x45a0]
[ 127.837950] Status: 1100dc03 KERNEL EXL IE
[ 127.842220] Cause : 00800008 (ExcCode 02)
[ 127.846285] BadVA : 7aba5d40
[ 127.849207] PrId : 0001974c (MIPS 74Kc)
[ 127.853182] Modules linked in: ath9k ath9k_common qcserial pppoe ppp_async opet sierra rndis_host qmi_wwan pwc pptp pppox ppp_generic nf_nat_pptp nf_conntracsunplus gspca_stv06xx gspca_stk014 gspca_sq905c gspca_sq905 gspca_spca561 gspca_ gspca_ov534 gspca_ov519 gspca_mr97310a gspca_mars gspca_main ebtable_nat ebtablta xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_xt_NETMAP xt_LOG xt_HL xt_DSCP xt_CT xt_CLASSIFY videobuf2_v4l2 usbserial usbneteject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_redirect nf_nat_protodefrag_ipv6 nf_defrag_ipv4 nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip[f_conntrack_amanda nf_conntrack iptable_mangle iptable_filter ipt_ECN ip_tables cdc_acm fuse sch_multiq em_nbyte sch_dsmark sch_pie sch_gred sch_teql em_cmp clw cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress videobuf2_vmalloc videobos[ 128.070146] ip_gre gre ip_tunnel rpcsec_gss_krb5 auth_rpcgss oid_registry ls_cp852 nls_cp850 nls_cp775 nls_cp437 nls_cp1251 nls_cp1250 dma_shared_buffer sore nls_base usb_common crc16 exportfs mii aead crypto_null cryptomgr crc32c_gen
[ 128.118175] Process bw_set (pid: 5426, threadinfo=85a26000, task=85a8df50, tl
[ 128.126377] Stack : 861ff7a0 861ff0b0 77a98000 00000054 00000002 00000000 5e7
[ 128.134913] 87730000 87730000 1fffffff 87730000 85a8df50 00000018 000
[ 128.143449] 01019c80 00000000 62646973 74342d64 6f776e6c 6f61642d 646
[ 128.151985] 00000021 00000041 2f757372 2f646174 612f6277 6d6f6e2f 620
[ 128.160521] 87734330 00000800 87d28500 7fedae14 00004000 77a9a000 77a
[ 128.169058] ...
[ 128.171548] Call Trace:[ 128.174003] [<87730000>] 0x87730000 [ipt_bandwidth@
[ 128.180478] [<87730000>] 0x87730000 [ipt_bandwidth@87730000+0x45a0]
[ 128.186955] [<87730000>] 0x87730000 [ipt_bandwidth@87730000+0x45a0]
[ 128.193460] [<802e4594>] 0x802e4594
[ 128.197001] [<80293b78>] 0x80293b78
[ 128.200625] [<80295510>] 0x80295510
[ 128.204165] [<80102804>] 0x80102804
[ 128.207704] [<8006f4cc>] 0x8006f4cc
[ 128.211242] [<8006f680>] 0x8006f680
[ 128.214777] [<80117ed8>] 0x80117ed8
[ 128.218317]
[ 128.219825] Code: 00000000 02331821 26620004 <8c750000> 1080009c 02221021
[ 128.229778]
[ 128.231347] ---[ end trace aa7954265135c613 ]---
[ 128.239723] Kernel panic - not syncing: Fatal exception in interrupt
[ 128.248292] Rebooting in 3 seconds..
***************************************
* U-Boot 1.1.4-7a540a78-clean *
* Build: 2018-02-23 *
***************************************
** Warning: bad env CRC, using default,
use 'saveenv' to save it in FLASH
** Warning: reset caused by watchdog!
BOARD: TP-Link TL-WDR3600 v1
SOC: AR9344 rev. 2
CPU: MIPS 74Kc
RAM: 128 MB DDR2 32-bit CL3-4-4-10
FLASH: 16 MB Winbond W25Q128
PCIe: 168C:0033
MAC: 64:70:02:D1:67:62
CLOCKS: CPU/RAM/AHB/SPI/REF
550/400/200/ 25/ 40 MHz
Hit any key to stop booting: 0
Booting image from 0x9F020000...
Vendor/image name: OpenWrt r7935-d08a63770c
Hardware ID: 0x36000001
Whole image size: 7.8 MB (8126464 bytes)
Kernel size: 1.3 MB (1385806 bytes)
Rootfs size: 5.7 MB (5958384 bytes)
Kernel load address: 0x80060000
Kernel entry point: 0x80060000
Header CRC... skipped
Data CRC... skipped
Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...
[ 0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (Ope
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 root
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.00
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i
[ 0.000011] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 78090
[ 0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[ 0.081683] pid_max: default: 32768 minimum: 301
[ 0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105222] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
[ 0.116230] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.124382] NET: Registered protocol family 16
[ 0.130969] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.140736] registering PCI controller with io_map_base unset
[ 0.396064] PCI host bridge to bus 0000:00
[ 0.400699] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.408362] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.414588] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.422153] pci_bus 0000:00: No busn resource found for root bus, will use [b
[ 0.431042] pci 0000:00:00.0: invalid calibration data
[ 0.437223] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bi
[ 0.445430] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref
[ 0.453491] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.462670] clocksource: Switched to clocksource MIPS
[ 0.469507] NET: Registered protocol family 2
[ 0.475410] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.483250] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.490350] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.497535] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.504094] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.511348] NET: Registered protocol family 1
[ 0.519426] Crashlog allocated RAM at address 0x3f00000
[ 0.526822] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.541420] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.547973] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
[ 0.569236] io scheduler noop registered
[ 0.573664] io scheduler deadline registered (default)
[ 0.579860] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.589903] console [ttyS0] disabled
[ 0.613998] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 250
[ 0.623630] console [ttyS0] enabled
[ 0.623630] console [ttyS0] enabled
[ 0.631045] bootconsole [early0] disabled
[ 0.631045] bootconsole [early0] disabled
[ 0.646356] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.660978] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.666125] 5 tp-link partitions found on MTD device spi0.0
[ 0.671781] Creating 5 MTD partitions on "spi0.0":
[ 0.676682] 0x000000000000-0x000000020000 : "u-boot"
[ 0.683853] 0x000000020000-0x000000172750 : "kernel"
[ 0.691087] 0x000000172750-0x000000ff0000 : "rootfs"
[ 0.697974] mtd: device 2 (rootfs) set to be root filesystem
[ 0.703814] 1 squashfs-split partitions found on MTD device rootfs
[ 0.710090] 0x000000730000-0x000000ff0000 : "rootfs_data"
[ 0.717923] 0x000000ff0000-0x000001000000 : "art"
[ 0.725003] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.733588] libphy: Fixed MDIO Bus: probed
[ 0.748779] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 1.415951] libphy: ag71xx_mdio: probed
[ 2.044076] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd0
[ 2.055650] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.064142] NET: Registered protocol family 10
[ 2.073163] NET: Registered protocol family 17
[ 2.077731] bridge: filtering via arp/ip/ip6tables is no longer available by
[ 2.091027] 8021q: 802.1Q VLAN Support v1.8
[ 2.097325] hctosys: unable to open rtc device (rtc0)
[ 2.106216] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.115065] Freeing unused kernel memory: 308K
[ 2.119573] This architecture does not have kernel memory protection.
[ 2.562686] random: fast init done
[ 2.791197] init: Console is alive
[ 2.794939] init: - watchdog -
[ 5.115655] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.400775] usbcore: registered new interface driver usbfs
[ 5.406507] usbcore: registered new interface driver hub
[ 5.412012] usbcore: registered new device driver usb
[ 5.456055] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.472612] SCSI subsystem initialized
[ 5.482376] ehci-platform: EHCI generic platform driver
[ 5.487846] ehci-platform ehci-platform: EHCI Host Controller
[ 5.493736] ehci-platform ehci-platform: new USB bus registered, assigned bus
[ 5.503890] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.532770] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.540099] hub 1-0:1.0: USB hub found
[ 5.544374] hub 1-0:1.0: 1 port detected
[ 5.553788] usbcore: registered new interface driver usb-storage
[ 5.569222] usbcore: registered new interface driver uas
[ 5.575500] kmodloader: done loading kernel modules from /etc/modules-boot.d/
[ 5.585317] init: - preinit -
[ 6.104945] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.306752] hub 1-1:1.0: USB hub found
[ 6.384483] hub 1-1:1.0: 4 ports detected
[ 6.466628] random: procd: uninitialized urandom read (4 bytes read)
[ 6.763958] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[ 6.842770] usb 1-1.1: new high-speed USB device number
] or [4] key and hit [enter] to select the debug level
[ 7.616412] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 7.623773] scsi host0: usb-storage 1-1.1:1.0
[ 7.722691] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[ 7.793936] eth0: link up (1000Mbps/Full duplex)
[ 7.798708] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.889573] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 7.896862] scsi host1: usb-storage 1-1.2:1.0
[ 8.002691] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[ 8.272691] usb 1-1.4: new full-speed USB device number 6 using ehci-platform
[ 8.472693] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[ 8.628373] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 8.636191] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[ 8.643931] usb-storage 1-1.4:1.2: USB Mass Storage device detected
[ 8.651653] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[ 8.659429] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[ 8.667185] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[ 8.675172] scsi host2: usb-storage 1-1.4:1.5
[ 8.680489] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[ 8.687898] scsi 0:0:0:0: Direct-Access ADATA USB Flash Drive 1100 PQ
[ 8.699094] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78
[ 8.707664] sd 0:0:0:0: [sda] Write Protect is off
[ 8.713332] sd 0:0:0:0: [sda] No Caching mode page found
[ 8.718777] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.726150] scsi host3: usb-storage 1-1.4:1.6
[ 8.736332] sda: sda1 sda2
[ 8.743554] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 9.720584] scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ
[ 9.794279] scsi 3:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ
[ 9.808688] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 10.043940] mount_root: loading kmods from internal overlay
[ 10.136778] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.152893] kmodloader: done loading kernel modules from //etc/modules-boot.d
[ 11.117483] jffs2: notice: (551) jffs2_build_xattr_subsystem: complete buildi
[ 11.133717] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 11.535596] scsi 1:0:0:0: Direct-Access Wilk USB DISK 2.0 PMAP PQ
[ 11.564189] sd 1:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.5
[ 11.606892] sd 1:0:0:0: [sdc] Write Protect is off
[ 11.622768] sd 1:0:0:0: [sdc] No Caching mode page found
[ 11.628203] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[ 11.708325] sdc: sdc1
/dev/sda1: recov[ 11.719081] sd 1:0:0:0: [sdc] Attached SCSI removable disk
ering journal
/dev/sda1: clean, 2932/185840 files, 43382/742784 blocks
[ 12.878835] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 12.987324] mount_root: switched to extroot
[ 12.996212] urandom-seed: Seeding with /etc/urandom.seed
[ 13.172862] eth0: link down
[ 13.189824] procd: - early -
[ 13.192992] procd: - watchdog -
[ 13.852990] procd: - watchdog -
[ 13.856434] procd: - ubus -
[ 14.253640] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.271917] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.282629] random: jshn: uninitialized urandom read (4 bytes read)
[ 14.290686] procd: - init -
Please press Enter to activate this console.
[ 15.879327] kmodloader: loading kernel modules from /etc/modules.d/*
[ 16.058673] Key type dns_resolver registered
[ 16.094418] RPC: Registered named UNIX socket transport module.
[ 16.100434] RPC: Registered udp transport module.
[ 16.105257] RPC: Registered tcp transport module.
[ 16.110025] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.135102] tun: Universal TUN/TAP device driver, 1.6
[ 16.140237] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 16.163689] gre: GRE over IPv4 demultiplexor driver
[ 16.171348] ip_gre: GRE over IPv4 tunneling driver
[ 16.217007] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 16.245207] i2c /dev entries driver
[ 16.264634] Linux video capture interface: v2.00
[ 16.302437] u32 classifier
[ 16.305250] input device check on
[ 16.308965] Actions configured
[ 16.316168] Mirror/redirect action on
[ 16.366358] fuse init (API version 7.26)
[ 16.469905] usbcore: registered new interface driver cdc_acm
[ 16.475736] cdc_acm: USB Abstract Control Model driver for USB modems and ISD
[ 16.547458] usbcore: registered new interface driver cdc_wdm
[ 16.564735] Loading modules backported from Linux version wt-2017-11-01-0-gfe
[ 16.572915] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 16.588948] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[ 16.595556] usbcore: registered new interface driver cpia2
[ 16.644903] Ebtables v2.0 registered
[ 16.675971] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.714735] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 17.340123] usbcore: registered new interface driver ums-alauda
[ 17.373836] usbcore: registered new interface driver ums-cypress
[ 17.394488] usbcore: registered new interface driver ums-datafab
[ 17.415438] usbcore: registered new interface driver ums-freecom
[ 17.435868] usbcore: registered new interface driver ums-isd200
[ 17.449376] usbcore: registered new interface driver ums-jumpshot
[ 17.467063] usbcore: registered new interface driver ums-karma
[ 17.488580] usbcore: registered new interface driver ums-sddr09
[ 17.535780] usbcore: registered new interface driver ums-sddr55
[ 17.596405] usbcore: registered new interface driver ums-usbat
[ 17.636903] usbcore: registered new interface driver usblp
[ 17.772832] usbcore: registered new interface driver usbserial
[ 17.778863] usbcore: registered new interface driver usbserial_generic
[ 17.785653] usbserial: USB Serial support registered for generic
[ 18.053746] xt_time: kernel timezone is -0000
[ 18.071555] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platf
[ 18.084258] usbcore: registered new interface driver cdc_ether
[ 18.119424] usbcore: registered new interface driver cdc_ncm
[ 18.244024] gspca_main: v2.14.0 registered
[ 18.271181] usbcore: registered new interface driver mars
[ 18.285550] usbcore: registered new interface driver mr97310a
[ 18.314786] usbcore: registered new interface driver ov519
[ 18.329717] usbcore: registered new interface driver ov534
[ 18.355670] usbcore: registered new interface driver ov534_9
[ 18.375593] usbcore: registered new interface driver pac207
[ 18.389827] usbcore: registered new interface driver pac7311
[ 18.405831] usbcore: registered new interface driver se401
[ 18.427083] usbcore: registered new interface driver gspca_sn9c20x
[ 18.468723] usbcore: registered new interface driver sonixb
[ 18.506675] usbcore: registered new interface driver sonixj
[ 18.535654] usbcore: registered new interface driver spca500
[ 18.565427] usbcore: registered new interface driver spca501
[ 18.575356] usbcore: registered new interface driver spca506
[ 18.605274] usbcore: registered new interface driver spca508
[ 18.627200] usbcore: registered new interface driver spca561
[ 18.665277] usbcore: registered new interface driver sq905
[ 18.691580] usbcore: registered new interface driver sq905c
[ 18.711906] usbcore: registered new interface driver stk014
[ 18.737236] usbcore: registered new interface driver STV06xx
[ 18.755827] usbcore: registered new interface driver sunplus
[ 18.769524] usbcore: registered new interface driver t613
[ 18.787198] usbcore: registered new interface driver tv8532
[ 18.805873] usbcore: registered new interface driver vc032x
[ 18.855969] usbcore: registered new interface driver gspca_zc3xx
[ 18.916643] usbcore: registered new interface driver huawei_cdc_ncm
[ 19.287203] PPP generic driver version 2.4.2
[ 19.314987] NET: Registered protocol family 24
[ 19.321924] PPTP driver version 0.8.5
[ 19.346370] usbcore: registered new interface driver Philips webcam
[ 19.375509] usbcore: registered new interface driver qmi_wwan
[ 19.398196] usbcore: registered new interface driver rndis_host
[ 19.427633] usbcore: registered new interface driver sierra
[ 19.433476] usbserial: USB Serial support registered for Sierra USB modem
[ 19.456643] usbcore: registered new interface driver sierra_net
[ 19.504953] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:07
[ 19.551406] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platfor
[ 19.562372] usbcore: registered new interface driver uvcvideo
[ 19.568251] USB Video Class driver (1.1.1)
[ 19.706703] usbcore: registered new interface driver cdc_mbim
[ 19.737266] usbcore: registered new interface driver conex
[ 19.765735] usbcore: registered new interface driver etoms
[ 19.795698] usbcore: registered new interface driver finepix
[ 19.827269] usbcore: registered new interface driver gspca_gl860
[ 19.856413] usbcore: registered new interface driver jeilinj
[ 19.881962] usbcore: registered new interface driver konica
[ 19.916148] usbcore: registered new interface driver ALi m5602
[ 19.964587] usbcore: registered new interface driver option
[ 19.970355] usbserial: USB Serial support registered for GSM modem (1-port)
[ 19.978417] option 1-1.4:1.0: GSM modem (1-port) converter detected
[ 19.985139] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[ 19.992719] option 1-1.4:1.3: GSM modem (1-port) converter detected
[ 19.999380] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[ 20.006566] option 1-1.4:1.4: GSM modem (1-port) converter detected
[ 20.013278] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[ 20.156481] usbcore: registered new interface driver qcserial
[ 20.162440] usbserial: USB Serial support registered for Qualcomm USB modem
[ 20.327332] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 20.334297] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 20.359766] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 20.573473] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 26.532753] random: crng init done
[ 26.536218] random: 6 urandom warning(s) missed due to ratelimiting
[ 33.290987] EXT4-fs (sdc1): recovery complete
[ 33.295464] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 36.215220] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 39.308305] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 41.028295] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 42.738481] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 42.850104] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 42.872650] br-lan: port 1(eth0.1) entered blocking state
[ 42.878204] br-lan: port 1(eth0.1) entered disabled state
[ 42.884130] device eth0.1 entered promiscuous mode
[ 42.889000] device eth0 entered promiscuous mode
[ 42.931178] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 43.004818] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 43.874202] eth0: link up (1000Mbps/Full duplex)
[ 43.879008] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 43.952855] br-lan: port 1(eth0.1) entered blocking state
[ 43.958347] br-lan: port 1(eth0.1) entered forwarding state
[ 43.964216] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 44.085268] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 47.767819] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 49.161597] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 49.190766] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 49.316602] br-lan: port 2(wlan1) entered blocking state
[ 49.322006] br-lan: port 2(wlan1) entered disabled state
[ 49.328006] device wlan1 entered promiscuous mode
[ 49.332933] br-lan: port 2(wlan1) entered blocking state
[ 49.338331] br-lan: port 2(wlan1) entered forwarding state
[ 49.397067] br-lan: port 3(wlan0) entered blocking state
[ 49.402523] br-lan: port 3(wlan0) entered disabled state
[ 49.408506] device wlan0 entered promiscuous mode
[ 50.364264] br-lan: port 2(wlan1) entered disabled state
[ 52.782720] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 52.789371] br-lan: port 3(wlan0) entered blocking state
[ 52.794838] br-lan: port 3(wlan0) entered forwarding state
[ 52.981483] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 52.988332] br-lan: port 2(wlan1) entered blocking state
[ 52.993783] br-lan: port 2(wlan1) entered forwarding state
[ 54.770761] 3g-wan: renamed from ppp0
[ 56.633101] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 95.624769] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[ 95.632022] old minutes west=0, new minutes west=-120
***************************************
* U-Boot 1.1.4-7a540a78-clean *
* Build: 2018-02-23 *
***************************************
** Warning: bad env CRC, using default,
use 'saveenv' to save it in FLASH
** Warning: reset caused by watchdog!
BOARD: TP-Link TL-WDR3600 v1
SOC: AR9344 rev. 2
CPU: MIPS 74Kc
RAM: 128 MB DDR2 32-bit CL3-4-4-10
FLASH: 16 MB Winbond W25Q128
PCIe: 168C:0033
MAC: 64:70:02:D1:67:62
CLOCKS: CPU/RAM/AHB/SPI/REF
550/400/200/ 25/ 40 MHz
Hit any key to stop booting: 0
Booting image from 0x9F020000...
Vendor/image name: OpenWrt r7935-d08a63770c
Hardware ID: 0x36000001
Whole image size: 7.8 MB (8126464 bytes)
Kernel size: 1.3 MB (1385806 bytes)
Rootfs size: 5.7 MB (5958384 bytes)
Kernel load address: 0x80060000
Kernel entry point: 0x80060000
Header CRC... skipped
Data CRC... skipped
Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...
[ 0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (Ope
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 root
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.00
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i
[ 0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 78090
[ 0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[ 0.081683] pid_max: default: 32768 minimum: 301
[ 0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.105220] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
[ 0.116230] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.124381] NET: Registered protocol family 16
[ 0.130974] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.140733] registering PCI controller with io_map_base unset
[ 0.396049] PCI host bridge to bus 0000:00
[ 0.400681] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.408345] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.414571] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.422136] pci_bus 0000:00: No busn resource found for root bus, will use [b
[ 0.431024] pci 0000:00:00.0: invalid calibration data
[ 0.437204] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bi
[ 0.445405] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref
[ 0.453465] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.462639] clocksource: Switched to clocksource MIPS
[ 0.469471] NET: Registered protocol family 2
[ 0.475377] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.483215] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.490315] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.497501] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.504060] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.511315] NET: Registered protocol family 1
[ 0.519394] Crashlog allocated RAM at address 0x3f00000
[ 0.526503] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.541099] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.547646] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
[ 0.569036] io scheduler noop registered
[ 0.573461] io scheduler deadline registered (default)
[ 0.579656] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.589699] console [ttyS0] disabled
[ 0.613796] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 250
[ 0.623434] console [ttyS0] enabled
[ 0.623434] console [ttyS0] enabled
[ 0.630849] bootconsole [early0] disabled
[ 0.630849] bootconsole [early0] disabled
[ 0.646131] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.660776] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.665930] 5 tp-link partitions found on MTD device spi0.0
[ 0.671585] Creating 5 MTD partitions on "spi0.0":
[ 0.676487] 0x000000000000-0x000000020000 : "u-boot"
[ 0.683668] 0x000000020000-0x000000172750 : "kernel"
[ 0.690903] 0x000000172750-0x000000ff0000 : "rootfs"
[ 0.697751] mtd: device 2 (rootfs) set to be root filesystem
[ 0.703592] 1 squashfs-split partitions found on MTD device rootfs
[ 0.709877] 0x000000730000-0x000000ff0000 : "rootfs_data"
[ 0.717741] 0x000000ff0000-0x000001000000 : "art"
[ 0.724809] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.733402] libphy: Fixed MDIO Bus: probed
[ 0.748834] switch0: Atheros AR8327 rev. 4 switch registered oCo poradzicie?