Auto calibration ---

U-Boot 2009.08 (Jul 03 2012 - 13:04:31)

CPU:   AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz)
       Security support
       Bootstrap Option D - Boot ROM Location NAND wo/ECC 2k page (8 bits), booting from NAND
       32 kB I-Cache 32 kB D-Cache
DNI HW ID: 29763875 NAND flash 128MB RAM 256MB U-Boot 2009.08 dni1 V1.4
Board: AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG
I2C:   ready
DRAM:  256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3)
NAND:  128 MiB
*** Warning - bad CRC, using default environment

PCIE0: link is not up.
PCIE0: initialization as root-complex failed
131072 bytes read: OK
Net:   ppc_4xx_eth0
AR8327 GigaSW initialize...done
ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0)

Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual

nmrp server is stopped or failed !

Type run flash_nfs to mount root filesystem over NFS

Hit any key to stop autoboot:  0

Loading from device 0: NAND 128MiB 3,3V 8-bit (offset 0x180000)

** check device-tree image **
   Verifying Checksum ... OK

** check kernel image **
   Verifying Checksum ... OK

** check rootfs image **
   Verifying Checksum ... OK

NAND read: device 0 offset 0x180000, size 0x20000
131072 bytes read: OK
## Booting kernel from Legacy Image at 00500000 ...
   Image Name:   POWERPC OpenWrt Linux-4.14.95
   Image Type:   PowerPC Linux Kernel Image (lzma compressed)
   Data Size:    1914440 Bytes =  1.8 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 00800040
   Booting using the fdt blob at 0x800040
   Uncompressing Kernel Image ... OK
[    0.000000] Linux version 4.14.95 (buildbot@builds-03.infra.lede-project.org) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7627-753531d)) #0 Mon Jan 28 08:54:32 2019
[    0.000000] Using WNDR4700 Platform machine description
[    0.000000] bootconsole [udbg0] enabled
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x10000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x0000000010100040
[    0.000000]   possible        = 0x0000000030100040
[    0.000000]   always          = 0x0000000000100000
[    0.000000] cpu_user_features = 0x8c008000 0x00000000
[    0.000000] mmu_features      = 0x00000008
[    0.000000] -----------------------------------------------------
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 254028K/262144K available (4492K kernel code, 200K rwdata, 588K rodata, 188K init, 233K bss, 8116K reserved, 0K cma-reserved)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
[    0.000000]   * 0xfde00000..0xfe000000  : consistent mem
[    0.000000]   * 0xfddfe000..0xfde00000  : early ioremap
[    0.000000]   * 0xd1000000..0xfddfe000  : vmalloc & ioremap
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] UIC0 (32 IRQ sources) at DCR 0xc0
[    0.000000] UIC1 (32 IRQ sources) at DCR 0xd0
[    0.000000] UIC2 (32 IRQ sources) at DCR 0xe0
[    0.000000] UIC3 (32 IRQ sources) at DCR 0xf0
[    0.000014] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.010321] clocksource: timebase mult[800000] shift[23] registered
[    0.016619] pid_max: default: 32768 minimum: 301
[    0.021267] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.027793] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.037887] random: get_random_u32 called from 0xc01e1670 with crng_init=0
[    0.044906] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.054559] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.061369] NET: Registered protocol family 16

[    0.067864] PPC4XX OCM1: 32768 Bytes (enabled)
[    0.072215] PPC4XX OCM1: 32768 Bytes (non-cached)
[    0.076875] PPC4XX OCM1: 0 Bytes (cached)
[    0.080906] debugfs ppc4xx ocm: failed to create file
[    0.086030] 256k L2-cache enabled
[    0.149418] PCIE0: Checking link...
[    0.453388] PCIE0: No device detected.
[    0.567559] PCI host bridge /plb/pciex@d00000000 (primary) ranges:
[    0.573652]  MEM 0x0000000e00000000..0x0000000e7fffffff -> 0x0000000080000000
[    0.580811]  MEM 0x0000000f00000000..0x0000000f000fffff -> 0x0000000000000000
[    0.587978]   IO 0x0000000f80000000..0x0000000f8000ffff -> 0x0000000000000000
[    0.595074] 4xx PCI DMA offset set to 0x00000000
[    0.599639] 4xx PCI DMA window base to 0x0000000000000000
[    0.604994] DMA window size 0x0000000080000000
[    0.609419] PCIE0: successfully set as root-complex
[    0.614816] PCI: Probing PCI hardware
[    0.618505] PCI host bridge to bus 0000:40
[    0.622521] pci_bus 0000:40: root bus resource [io  0x0000-0xffff]
[    0.628640] pci_bus 0000:40: root bus resource [mem 0xe00000000-0xe7fffffff] (bus address [0x80000000-0xffffffff])
[    0.638920] pci_bus 0000:40: root bus resource [mem 0xf00000000-0xf000fffff] (bus address [0x00000000-0x000fffff])
[    0.649202] pci_bus 0000:40: root bus resource [bus 40-ff]
[    0.654746] PCI: Hiding 4xx host bridge resources 0000:40:00.0
[    0.660760] pci 0000:40:00.0: PCI bridge to [bus 41-7f]
[    0.665950] pci 0000:40:00.0: Max Payload Size set to  128/ 128 (was  128), Max Read Rq  512
[    0.674291] pci 0000:40:00.0: disabling bridge window [io  0x0000-0xffffffffffffffff] to [bus 41-7f] (unused)
[    0.684128] pci 0000:40:00.0: disabling bridge window [mem 0x00000000-0xffffffffffffffff 64bit pref] to [bus 41-7f] (unused)
[    0.695262] pci 0000:40:00.0: disabling bridge window [mem 0x00000000-0xffffffffffffffff] to [bus 41-7f] (unused)
[    0.705461] pci 0000:40:00.0: PCI bridge to [bus 41-7f]
[    0.718106] SCSI subsystem initialized
[    0.724056] clocksource: Switched to clocksource timebase
[    0.730266] NET: Registered protocol family 2
[    0.734945] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.741827] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.748117] TCP: Hash tables configured (established 2048 bind 2048)
[    0.754497] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.760247] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.766570] NET: Registered protocol family 1
[    0.773722] dw_dmac 4bffd0800.dma: DesignWare DMA Controller, 2 channels
[    0.781185] OF: /plb/opb/gpio@ef600b00: could not find phandle
[    0.791277] Crashlog allocated RAM at address 0x3f00000
[    0.797068] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    0.806317] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.820322] io scheduler noop registered
[    0.824163] io scheduler deadline registered (default)
[    0.829797] aer: probe of 0000:40:00.0:pcie002 failed with error -22
[    0.836114] pcie_pme: probe of 0000:40:00.0:pcie001 failed with error -22
[    0.842906] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
▒[    0.874234] serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 19, base_baud = 347222) is a U6_16550A
[    0.883018] console [ttyS0] enabled
[    0.883018] console [ttyS0] enabled
[    0.889908] bootconsole [udbg0] disabled
[    0.889908] bootconsole [udbg0] disabled
[    0.898166] console [ttyS0] disabled
[    0.901791] console [ttyS0] enabled
[    0.905726] sata-dwc 4bffd1800.sata: id 0, controller version 1.91
[    0.915650] scsi host0: sata-dwc
[    0.919114] ata1: SATA max UDMA/133 irq 33
[    0.924552] nand: Could not find valid ONFI parameter page; aborting
[    0.930906] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    0.937237] nand: Hynix NAND 128MiB 3,3V 8-bit
[    0.941670] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.949228] Scanning device for bad blocks
[    1.005022] Bad eraseblock 840 at 0x000006900000
[    1.021075] 12 fixed-partitions partitions found on MTD device 4e4000000.ndfc.nand
[    1.028622] Creating 12 MTD partitions on "4e4000000.ndfc.nand":
[    1.034614] 0x000000000000-0x000008000000 : "NAND 128MiB 3,3V 8-bit"
[    1.042253] 0x000000000000-0x000000180000 : "uboot"
[    1.047547] 0x000000180000-0x0000001a0000 : "device-tree"
[    1.053393] 0x000000180000-0x000000500000 : "kernel"
[    1.058784] 0x000000500000-0x0000019e0000 : "ubi"
[    1.064018] 0x0000019e0000-0x000001a60000 : "config"
[    1.069422] 0x000001a60000-0x000001ae0000 : "pot"
[    1.074557] 0x000001ae0000-0x000001de0000 : "traffic_meter"
[    1.080575] 0x000001de0000-0x000001fa0000 : "language"
[    1.086151] 0x000001fa0000-0x000007fc0000 : "ecos"
[    1.091940] 0x000007fc0000-0x000008000000 : "wifi_data"
[    1.097594] 0x000000180000-0x0000019e0000 : "firmware"
[    1.103656] libphy: Fixed MDIO Bus: probed
[    1.107764] PPC 4xx OCP EMAC driver, version 3.54
[    1.112761] MAL v2 /plb/mcmal, 1 TX channels, 1 RX channels
[    1.118491] RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
[    1.125649] TAH /plb/opb/emac-tah@ef601350 initialized
[    1.131081] /plb/opb/emac-rgmii@ef601500: input 0 in rgmii mode
[    1.137094] libphy: emac_mdio: probed
[    1.146751] switch0: Atheros AR8327 rev. 4 switch registered on 4ef600c00.ethernet
[    1.257129] ata1: SATA link down (SStatus 0 SControl 300)
[    1.704693] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 10:0d:7f:66:d6:02
[    1.711561] eth0: found Atheros AR8216/AR8236/AR8316 PHY (0x00)
[    1.717631] i2c /dev entries driver
[    1.721540] ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
[    1.748205] booke_wdt: powerpc book-e watchdog driver loaded
[    1.756592] NET: Registered protocol family 10
[    1.762409] Segment Routing with IPv6
[    1.766141] NET: Registered protocol family 17
[    1.770609] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.783519] 8021q: 802.1Q VLAN Support v1.8
[    1.789663] UBI: auto-attach mtd4
[    1.793005] ubi0: attaching mtd4
[    1.804933] UBI: EOF marker found, PEBs from 29 will be erased
[    1.810894] ubi0: scanning is finished
[    1.836533] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 116 LEBs
[    1.843543] ubi0: attached mtd4 (name "ubi", size 20 MiB)
[    1.848950] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.855799] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.862477] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[    1.869241] ubi0: good PEBs: 167, bad PEBs: 0, corrupted PEBs: 0
[    1.875221] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    1.882420] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1938569744
[    1.891516] ubi0: available PEBs: 0, total reserved PEBs: 167, PEBs reserved for bad PEB handling: 20
[    1.900733] ubi0: background thread "ubi_bgt0d" started, PID 431
[    1.907791] block ubiblock0_0: created from ubi0:0(rootfs)
[    1.913285] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    1.920223] hctosys: unable to open rtc device (rtc0)
[    1.956695] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.964468] Freeing unused kernel memory: 188K
[    2.357860] init: Console is alive
[    2.361424] init: - watchdog -
[    3.020976] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.064573] usbcore: registered new interface driver usbfs
[    3.070111] usbcore: registered new interface driver hub
[    3.075476] usbcore: registered new device driver usb
[    3.208152] dwc2 4bff80000.usbotg: DWC OTG Controller
[    3.213235] dwc2 4bff80000.usbotg: new USB bus registered, assigned bus number 1
[    3.220644] dwc2 4bff80000.usbotg: irq 34, io mem 0x4bff80000
[    3.226963] hub 1-0:1.0: USB hub found
[    3.230891] hub 1-0:1.0: 1 port detected
[    3.246431] usbcore: registered new interface driver usb-storage
[    3.252918] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.262844] init: - preinit -
[    3.547036] eth0: link is up, 1000 FDX
[    3.551130] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    3.556990] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    3.571966] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    3.640077] usb 1-1: new high-speed USB device number 2 using dwc2
[    3.836361] usb-storage 1-1:1.0: USB Mass Storage device detected
[    3.842816] scsi host1: usb-storage 1-1:1.0
[    4.909293] scsi 1:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9454 PQ: 0 ANSI: 0
[    4.919760] sd 1:0:0:0: [sda] Attached SCSI removable disk
[    6.677292] mount_root: loading kmods from internal overlay
[    6.695208] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.702932] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    7.148109] print_req_error: I/O error, dev mtdblock5, sector 32
[    7.167004] print_req_error: I/O error, dev mtdblock5, sector 32
[    7.173064] print_req_error: I/O error, dev mtdblock5, sector 32
[    7.179049] Buffer I/O error on dev mtdblock5, logical block 4, async page read
[    7.444673] UBIFS (ubi0:1): default file-system created
[    7.454234] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 559
[    7.517124] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    7.524940] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.534813] UBIFS (ubi0:1): FS size: 13676544 bytes (13 MiB, 106 LEBs), journal size 1032193 bytes (0 MiB, 6 LEBs)
[    7.545118] UBIFS (ubi0:1): reserved for root: 645976 bytes (630 KiB)
[    7.551606] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 42E3A592-8932-4BC8-A272-C6E7114AC483, small LPT model
[    7.563724] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    7.570804] block: unable to load configuration (fstab: Entry not found)
[    7.577554] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[    7.584087] block: unable to load configuration (fstab: Entry not found)
[    7.590830] block: attempting to load /etc/config/fstab
[    7.596171] block: unable to load configuration (fstab: Entry not found)
[    7.602912] block: no usable configuration
[    7.610943] UBIFS (ubi0:1): un-mount UBI device 0
[    7.615654] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[    7.629193] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 562
[    7.692115] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    7.699926] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.709801] UBIFS (ubi0:1): FS size: 13676544 bytes (13 MiB, 106 LEBs), journal size 1032193 bytes (0 MiB, 6 LEBs)
[    7.720104] UBIFS (ubi0:1): reserved for root: 645976 bytes (630 KiB)
[    7.726526] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 42E3A592-8932-4BC8-A272-C6E7114AC483, small LPT model
[    8.075667] print_req_error: I/O error, dev mtdblock5, sector 32
[    8.094544] print_req_error: I/O error, dev mtdblock5, sector 32
[    8.100592] print_req_error: I/O error, dev mtdblock5, sector 32
[    8.106578] Buffer I/O error on dev mtdblock5, logical block 4, async page read
[    8.366391] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    8.373447] block: unable to load configuration (fstab: Entry not found)
[    8.380191] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[    8.386716] block: unable to load configuration (fstab: Entry not found)
[    8.393460] block: attempting to load /etc/config/fstab
[    8.398759] block: unable to load configuration (fstab: Entry not found)
[    8.405497] block: no usable configuration
[    8.410899] mount_root: overlay filesystem has not been fully initialized yet
[    8.418464] mount_root: switching to ubifs overlay
[    8.445489] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.484165] procd: - early -
[    8.487132] procd: - watchdog -
[    9.052798] procd: - watchdog -
[    9.056176] procd: - ubus -
[    9.106097] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.114461] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.121109] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.128033] procd: - init -
Please press Enter to activate this console.
[    9.296249] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.318668] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    9.339641] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.352026] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[    9.360035] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[    9.368475] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.379715] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[    9.416654] xt_time: kernel timezone is -0000
[    9.465537] PPP generic driver version 2.4.2
[    9.471399] NET: Registered protocol family 24
[    9.497272] kmodloader: done loading kernel modules from /etc/modules.d/*
[   10.691400] urandom_read: 5 callbacks suppressed
[   10.691407] random: jshn: uninitialized urandom read (4 bytes read)
[   15.815364] print_req_error: I/O error, dev mtdblock5, sector 32
[   15.869116] print_req_error: I/O error, dev mtdblock5, sector 32
[   15.888092] print_req_error: I/O error, dev mtdblock5, sector 32
[   15.894081] Buffer I/O error on dev mtdblock5, logical block 4, async page read
[   17.453580] eth0: link is up, 1000 FDX
[   17.476712] br-lan: port 1(eth0.1) entered blocking state
[   17.482127] br-lan: port 1(eth0.1) entered disabled state
[   17.487722] device eth0.1 entered promiscuous mode
[   17.492517] device eth0 entered promiscuous mode
[   17.598115] br-lan: port 1(eth0.1) entered blocking state
[   17.603519] br-lan: port 1(eth0.1) entered forwarding state
[   17.609354] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   18.476218] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready