• Zarejestrowany: 2012-11-03
  • Posty: 16

Temat: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

Witam,
proszę o pomoc i sprawdzenie dlaczego nie wykrywa mi modemu (E173s-2) na firmware LEDE.
Dodam tylko, że na firmware MiFi modem jest wykrywany.

2 Odpowiedź przez maly310

  • Zarejestrowany: 2012-11-03
  • Posty: 16

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

log z LEDE


root@MiFi:/# sysupgrade -n /tmp/lede.bin
Image metadata not found
killall: watchdog: no process killed
Sending TERM to remaining processes ... uhttpd ntpd udhcpc dnsmasq ubusd logd rpcd netifd
Sending KILL to remaining processes ...
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...
Upgrade completed
Rebooting system...
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[  775.304599] reboot: Restarting system


U-Boot 1.3.0-TT-0.1.0 (Nov 29 2011 - 19:22:17)@TTHR

AP99 (ar7240 - Python) U-boot
ar7240_ddr_initial_config(137): python ddr init
#### TAP VALUE 1 = 0x8, 2 = 0x8 [0x2: 0xe]
CPU_FREQ=400##DDR_FREQ=400##AHB_FREQ=200
DRAM:  64 MB
Flash: 16 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
ag7240_get_ethaddr Fetching MAC Address from 0x9f01fc00
ag7240_get_ethaddr Fetching MAC Address from 0x9f01fc00
: cfg1 0xf cfg2 0x7014
eth0: f4:ec:38:70:7b:98
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: f4:ec:38:70:7b:99
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         F4:EC:38:70:7B:98
Address in environment is  40:16:FFFFFF9F:FFFFFFAB:FFFFFFE0:FFFFFF82
, eth1
Autobooting in 1 seconds press tt to abort
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...



OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

[    0.000000] Linux version 4.4.147 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3785-ceea0ac) ) #0 Fri Aug 10 20:56:50 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7240 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] No valid device tree found, continuing without
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: board=TL-MR3220  console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59904K/65536K available (3132K kernel code, 160K rwdata, 780K rodata, 336K init, 205K bss, 5632K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.007894] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.090597] pid_max: default: 32768 minimum: 301
[    0.095388] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.101995] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.112816] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.122678] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.130572] NET: Registered protocol family 16
[    0.137121] MIPS: machine is TP-LINK TL-MR3220
[    0.577342] registering PCI controller with io_map_base unset
[    1.593358] PCI host bridge to bus 0000:00
[    1.597535] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    1.604394] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.609963] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.616733] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.624738] pci 0000:00:00.0: fixup device configuration
[    1.631895] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    1.639248] pci 0000:00:00.0: using irq 40 for pin 1
[    1.645436] clocksource: Switched to clocksource MIPS
[    1.652445] NET: Registered protocol family 2
[    1.658182] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.665161] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.671589] TCP: Hash tables configured (established 1024 bind 1024)
[    1.678096] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.683948] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.690649] NET: Registered protocol family 1
[    1.701782] Crashlog allocated RAM at address 0x3f00000
[    1.728635] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.734472] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.747920] io scheduler noop registered
[    1.751851] io scheduler deadline registered (default)
[    1.757422] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    1.767925] console [ttyS0] disabled
[    1.791539] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[    1.800237] console [ttyS0] enabled
[    1.800237] console [ttyS0] enabled
[    1.807256] bootconsole [early0] disabled
[    1.807256] bootconsole [early0] disabled
[    1.822204] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    1.828103] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    1.834634] 5 tp-link partitions found on MTD device spi0.0
[    1.840301] Creating 5 MTD partitions on "spi0.0":
[    1.845134] 0x000000000000-0x000000020000 : "u-boot"
[    1.852071] 0x000000020000-0x0000001710d8 : "kernel"
[    1.859356] 0x0000001710d8-0x000000ff0000 : "rootfs"
[    1.866611] mtd: device 2 (rootfs) set to be root filesystem
[    1.872358] 1 squashfs-split partitions found on MTD device rootfs
[    1.878664] 0x000000390000-0x000000ff0000 : "rootfs_data"
[    1.886402] 0x000000ff0000-0x000001000000 : "art"
[    1.893374] 0x000000020000-0x000000ff0000 : "firmware"
[    1.925923] libphy: ag71xx_mdio: probed
[    2.516933] ag71xx-mdio.0: Found an AR7240/AR9330 built-in switch
[    2.558970] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    3.149174] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[    3.159350] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    3.168429] NET: Registered protocol family 10
[    3.178302] NET: Registered protocol family 17
[    3.182873] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.195787] 8021q: 802.1Q VLAN Support v1.8
[    3.202468] hctosys: unable to open rtc device (rtc0)
[    3.212802] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.222719] Freeing unused kernel memory: 336K
[    4.502866] init: Console is alive
[    4.506653] init: - watchdog -
[    6.150751] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.275343] usbcore: registered new interface driver usbfs
[    6.281057] usbcore: registered new interface driver hub
[    6.286564] usbcore: registered new device driver usb
[    6.343989] SCSI subsystem initialized
[    6.356065] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.364771] ehci-platform: EHCI generic platform driver
[    6.375906] usbcore: registered new interface driver usb-storage
[    6.382704] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.392490] init: - preinit -
[    7.229070] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    7.262126] random: procd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.326832] eth0: link up (1000Mbps/Full duplex)
[    9.331556] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   10.529374] mount_root: loading kmods from internal overlay
[   10.560818] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.569694] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   10.923447] block: attempting to load /etc/config/fstab
[   10.929162] block: unable to load configuration (fstab: Entry not found)
[   10.936069] block: no usable configuration
[   10.941029] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   10.953575] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.999485] eth0: link down
[   11.016886] procd: - early -
[   11.019900] procd: - watchdog -
[   11.696362] procd: - watchdog -
[   11.699849] procd: - ubus -
[   12.017756] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.027401] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.036616] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.046140] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.055214] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.064570] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.073872] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.083437] procd: - init -
Please press Enter to activate this console.
[   12.511569] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.526142] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   12.534202] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   12.552136] nf_conntrack version 0.5.0 (941 buckets, 3764 max)
[   12.605970] xt_time: kernel timezone is -0000
[   12.639507] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.701518] PPP generic driver version 2.4.2
[   12.709394] NET: Registered protocol family 24
[   12.767672] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   12.778498] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   12.785661] ath: phy0: Enable LNA combining
[   12.813409] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[   12.972942] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.279901] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[   14.386667] random: jshn: uninitialized urandom read (4 bytes read, 23 bits of entropy available)
[   20.742955] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   20.765572] jffs2_build_filesystem(): unlocking the mtd device... done.
[   20.772249] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   26.880621] device eth0 entered promiscuous mode
[   26.894542] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   27.000631] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   28.976846] eth0: link up (1000Mbps/Full duplex)
[   28.981559] br-lan: port 1(eth0) entered forwarding state
[   28.987075] br-lan: port 1(eth0) entered forwarding state
[   29.007426] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   29.377067] eth1: link up (100Mbps/Full duplex)
[   29.381673] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   30.985456] br-lan: port 1(eth0) entered forwarding state
[   80.485495] random: nonblocking pool is initialized



BusyBox v1.25.1 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
/________/  LE  \  |____|___|___/|___|                      lede-project.org
\        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (17.01-SNAPSHOT, r3948-5886a5060a)
    \________\/    -----------------------------------------------------------

-----------------------------------------------------------------------------
|                                                                           |
| Build time: 2018-08-15 07:21 CEST                                         |
|                                                                           |
| Cezary Jackiewicz (obsy), http://eko.one.pl                               |
|                                                                           |
-----------------------------------------------------------------------------
| Machine: TP-Link TL-MR3220 v1                                             |
| Uptime: 0d, 00:01:26                                                      |
| Load: 1.73 0.57 0.20                                                      |
| Flash: total: 29.4MB, free: 29.4MB, used: 0%                              |
| Memory: total: 58.8MB, free: 47.0MB, used: 20%                            |
| WAN: 192.168.88.251, proto: dhcp                                          |
| LAN: 192.168.1.1, leases: 0                                               |
-----------------------------------------------------------------------------
=== WARNING! ================================================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password in order to prevent
unauthorized SSH logins.
-----------------------------------------------------------------------------
root@LEDE:/# passwd
Changing password for root
New password:
Bad password: too weak
Retype password:
passwd: password for root changed by root
root@LEDE:/# [  102.725754] eth0: link down
[  102.729068] br-lan: port 1(eth0) entered disabled state
[  103.375899] eth1: link down
[  104.226854] eth0: link up (1000Mbps/Full duplex)
[  104.231568] br-lan: port 1(eth0) entered forwarding state
[  104.237086] br-lan: port 1(eth0) entered forwarding state
[  104.377065] eth1: link up (100Mbps/Full duplex)
[  106.235456] br-lan: port 1(eth0) entered forwarding state
[  110.075662] done.
[  110.077667] jffs2: notice: (904) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

root@LEDE:/#

3 Odpowiedź przez maly310

  • Zarejestrowany: 2012-11-03
  • Posty: 16

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

log z MiFi


root@SPAK:/# sysupgrade -n /tmp/mifi.bin
Image metadata not found
killall: watchdog: no process killed
Sending TERM to remaining processes ... udhcpc dnsmasq ubusd logd rpcd netifd uhttpd ntpd
Sending KILL to remaining processes ...
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...

Writing from <stdin> to firmware ...
Upgrade completed
Rebooting system...
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
[ 1077.289758] Removing MTD device #3 (rootfs_data) with use count 1
[ 1077.313551] reboot: Restarting system


U-Boot 1.3.0-TT-0.1.0 (Nov 29 2011 - 19:22:17)@TTHR

AP99 (ar7240 - Python) U-boot
ar7240_ddr_initial_config(137): python ddr init
#### TAP VALUE 1 = 0x8, 2 = 0x8 [0x2: 0xe]
CPU_FREQ=400##DDR_FREQ=400##AHB_FREQ=200
DRAM:  64 MB
Flash: 16 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
ag7240_get_ethaddr Fetching MAC Address from 0x9f01fc00
ag7240_get_ethaddr Fetching MAC Address from 0x9f01fc00
: cfg1 0xf cfg2 0x7014
eth0: f4:ec:38:70:7b:98
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: f4:ec:38:70:7b:99
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0
Warning: eth0 MAC addresses don't match:
Address in SROM is         F4:EC:38:70:7B:98
Address in environment is  40:16:FFFFFF9F:FFFFFFAB:FFFFFFE0:FFFFFF82
, eth1
Autobooting in 1 seconds press tt to abort
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...



OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Looking for OpenWrt image... found at 0xbf022000
Decompressing kernel... done!
Starting kernel at 80060000...

[    0.000000] Linux version 4.4.140 (cezary@eko.one.pl) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3785-ceea0ac) ) #0 Tue Jul 17 05:17:48 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7240 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] No valid device tree found, continuing without
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: board=TL-MR3220  console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59904K/65536K available (3130K kernel code, 162K rwdata, 780K rodata, 336K init, 205K bss, 5632K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.007894] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.090597] pid_max: default: 32768 minimum: 301
[    0.095386] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.101996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.112825] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.122684] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.130581] NET: Registered protocol family 16
[    0.137171] MIPS: machine is TP-LINK TL-MR3220
[    0.577354] registering PCI controller with io_map_base unset
[    1.593509] PCI host bridge to bus 0000:00
[    1.597690] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    1.604541] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.610109] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.616880] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.624885] pci 0000:00:00.0: fixup device configuration
[    1.632045] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[    1.639401] pci 0000:00:00.0: using irq 40 for pin 1
[    1.645580] clocksource: Switched to clocksource MIPS
[    1.652591] NET: Registered protocol family 2
[    1.658335] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    1.665308] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    1.671735] TCP: Hash tables configured (established 1024 bind 1024)
[    1.678241] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.684095] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.690795] NET: Registered protocol family 1
[    1.701962] Crashlog allocated RAM at address 0x3f00000
[    1.729029] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.734868] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.748331] io scheduler noop registered
[    1.752265] io scheduler deadline registered (default)
[    1.757832] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    1.768357] console [ttyS0] disabled
[    1.791970] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[    1.800670] console [ttyS0] enabled
[    1.800670] console [ttyS0] enabled
[    1.807688] bootconsole [early0] disabled
[    1.807688] bootconsole [early0] disabled
[    1.822712] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    1.828605] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    1.835140] 5 tp-link partitions found on MTD device spi0.0
[    1.840806] Creating 5 MTD partitions on "spi0.0":
[    1.845648] 0x000000000000-0x000000020000 : "u-boot"
[    1.852589] 0x000000020000-0x000000170d84 : "kernel"
[    1.859872] 0x000000170d84-0x000000ff0000 : "rootfs"
[    1.867149] mtd: device 2 (rootfs) set to be root filesystem
[    1.872886] 1 squashfs-split partitions found on MTD device rootfs
[    1.879186] 0x000000380000-0x000000ff0000 : "rootfs_data"
[    1.886922] 0x000000ff0000-0x000001000000 : "art"
[    1.893890] 0x000000020000-0x000000ff0000 : "firmware"
[    1.926552] libphy: ag71xx_mdio: probed
[    2.517074] ag71xx-mdio.0: Found an AR7240/AR9330 built-in switch
[    2.559121] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    3.149318] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[    3.159499] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    3.168597] NET: Registered protocol family 10
[    3.178486] NET: Registered protocol family 17
[    3.183065] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.195972] 8021q: 802.1Q VLAN Support v1.8
[    3.202662] hctosys: unable to open rtc device (rtc0)
[    3.213370] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.223288] Freeing unused kernel memory: 336K
[    4.586545] init: Console is alive
[    4.590232] init: - watchdog -
[    6.042457] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.133865] usbcore: registered new interface driver usbfs
[    6.139610] usbcore: registered new interface driver hub
[    6.145082] usbcore: registered new device driver usb
[    6.157209] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.165965] ehci-platform: EHCI generic platform driver
[    6.174921] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.183028] ohci-platform: OHCI generic platform driver
[    6.188517] ohci-platform ohci-platform: Generic Platform OHCI controller
[    6.195402] ohci-platform ohci-platform: new USB bus registered, assigned bus number 1
[    6.203487] ohci-platform ohci-platform: irq 3, io mem 0x1b000000
[    6.270883] hub 1-0:1.0: USB hub found
[    6.275072] hub 1-0:1.0: 1 port detected
[    6.280213] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.298072] init: - preinit -
[    6.959215] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    6.992931] random: procd: uninitialized urandom read (4 bytes read, 11 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.056976] eth0: link up (1000Mbps/Full duplex)
[    9.061699] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   10.327400] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   10.339876] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.587666] eth0: link down
[   10.604148] procd: - early -
[   10.608080] procd: - watchdog -
[   11.301745] random: jshn: uninitialized urandom read (4 bytes read, 18 bits of entropy available)
[   11.421690] procd: - watchdog -
[   11.425188] procd: - ubus -
[   11.973493] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   11.996066] random: ubusd: uninitialized urandom read (4 bytes read, 19 bits of entropy available)
[   12.016002] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.025104] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.053405] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.065775] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.081218] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.090577] random: ubusd: uninitialized urandom read (4 bytes read, 20 bits of entropy available)
[   12.100221] procd: - init -
Please press Enter to activate this console.
[   12.647236] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.673211] usbcore: registered new interface driver cdc_wdm
[   12.687988] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   12.696125] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   12.733661] nf_conntrack version 0.5.0 (941 buckets, 3764 max)
[   12.867379] usbcore: registered new interface driver usbserial
[   12.873394] usbcore: registered new interface driver usbserial_generic
[   12.880198] usbserial: USB Serial support registered for generic
[   12.957956] xt_time: kernel timezone is -0000
[   12.970614] usbcore: registered new interface driver cdc_ether
[   12.989342] usbcore: registered new interface driver cdc_ncm
[   13.054894] usbcore: registered new interface driver huawei_cdc_ncm
[   13.074846] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.219860] PPP generic driver version 2.4.2
[   13.248660] usbcore: registered new interface driver qmi_wwan
[   13.258436] usbcore: registered new interface driver rndis_host
[   13.278215] usbcore: registered new interface driver sierra
[   13.283958] usbserial: USB Serial support registered for Sierra USB modem
[   13.308530] usbcore: registered new interface driver sierra_net
[   13.410441] usbcore: registered new interface driver option
[   13.416296] usbserial: USB Serial support registered for GSM modem (1-port)
[   13.437850] usbcore: registered new interface driver qcserial
[   13.443771] usbserial: USB Serial support registered for Qualcomm USB modem
[   13.503420] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   13.514312] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   13.521514] ath: phy0: Enable LNA combining
[   13.549502] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[   13.616125] kmodloader: done loading kernel modules from /etc/modules.d/*
[   25.322937] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   25.355728] jffs2_build_filesystem(): unlocking the mtd device... done.
[   25.362403] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   31.730734] device eth0 entered promiscuous mode
[   31.748717] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   31.868519] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   33.827001] eth0: link up (1000Mbps/Full duplex)
[   33.831709] br-lan: port 1(eth0) entered forwarding state
[   33.837233] br-lan: port 1(eth0) entered forwarding state
[   33.864381] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   33.987210] eth1: link up (100Mbps/Full duplex)
[   33.991812] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   35.835609] br-lan: port 1(eth0) entered forwarding state
[   37.307115] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   37.381320] device wlan0 entered promiscuous mode
[   40.805178] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   40.811853] br-lan: port 2(wlan0) entered forwarding state
[   40.817470] br-lan: port 2(wlan0) entered forwarding state
[   42.815712] br-lan: port 2(wlan0) entered forwarding state
[   61.341880] random: nonblocking pool is initialized



BusyBox v1.25.1 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
/________/  LE  \  |____|___|___/|___|                      lede-project.org
\        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (17.01-SNAPSHOT, r3925-79c8f2f50b)
    \________\/    -----------------------------------------------------------

-----------------------------------------------------------------------------
|                                                                           |
| Build time: 2018-07-18 15:53 CEST                                         |
|                                                                           |
| Cezary Jackiewicz (obsy), http://eko.one.pl                               |
|                                                                           |
-----------------------------------------------------------------------------
| Machine: TP-Link TL-MR3220 v1                                             |
| Uptime: 0d, 00:01:42                                                      |
| Load: 1.64 0.67 0.25                                                      |
| Flash: total: 29.4MB, free: 29.4MB, used: 0%                              |
| Memory: total: 58.8MB, free: 46.7MB, used: 20%                            |
| WAN: 192.168.88.251, proto: dhcp                                          |
| LAN: 192.168.11.1, leases: 0                                              |
| radio0: mode: ap, ssid: mifi-707b97, channel: 11, conn: 0                 |
-----------------------------------------------------------------------------
root@MiFi:/# [  112.246338] done.
[  112.248373] jffs2: notice: (1065) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  116.005619] usb 1-1: new full-speed USB device number 2 using ohci-platform
[  117.042402] usb 1-1: USB disconnect, device number 2
[  121.485621] usb 1-1: new full-speed USB device number 3 using ohci-platform
[  121.988338] option 1-1:1.0: GSM modem (1-port) converter detected
[  121.994942] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[  122.002705] option 1-1:1.1: GSM modem (1-port) converter detected
[  122.009366] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[  122.016958] option 1-1:1.2: GSM modem (1-port) converter detected
[  122.023497] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2

root@MiFi:/# passwd
Changing password for root
New password:
Bad password: too weak
Retype password:
passwd: password for root changed by root
root@MiFi:/#
root@MiFi:/# root@SPAK:/# sysupgrade -n /tmp/mifi.bin
metadata not found
/bin/ash: root@SPAK:/#: not found
root@MiFi:/# Image metadata not found
ocess killed
Sending TERM to remaining processes ... udhcpc dnsm/bin/ash: Image: not found
root@MiFi:/# killall: watchdog: no process killed
pcd netifd uhttpd ntpd
Sending KILL to remaining proces/bin/ash: killall:: not found
ses ...
root@MiFi:/# Sending TERM to remaining processes ... udhcpc dnsmasq ubusd logd r
pcd netifd uhttpd ntpd
ng syste/bin/ash: Sending: not found
m upgradroot@MiFi:/# Sending KILL to remaining processes ...
/bin/ash: Sending: not found
root@MiFi:/# Switching to ramdisk...
om <stdi/bin/ash: Switching: not found
n> to firoot@MiFi:/# Performing system upgrade...
de compl/bin/ash: Performing: not found
root@MiFi:/# Unlocking firmware ...
/bin/ash: Unlocking: not found
ystem...root@MiFi:/#
root@MiFi:/# Writing from <stdin> to firmware ...
nmount //bin/ash: can't open stdin: no such file
/bin/ash: Writing: not found
root@MiFi:/# Upgrade completed
usy
umou/bin/ash: Upgrade: not found
root@MiFi:/# Rebooting system...
/bin/ash: Rebooting: not found
root@MiFi:/# umount: can't unmount /dev: Resource busy
> umount: can't unmount /tmp: Resource busy
oving MT/bin/ash: umount:: not found
D deviceroot@MiFi:/# [ 1077.289758] Removing MTD device #3 (rootfs_data) with use count
1
ash: missing ]
77.31355root@MiFi:/# [ 1077.313551] reboot: Restarting system
ash: missing ]
-Boot 1.root@MiFi:/#
root@MiFi:/#
root@MiFi:/# U-Boot 1.3.0-TT-0.1.0 (Nov 29 2011 - 19:22:17)@TTHR
/bin/ash: syntax error: unexpected "("
root@MiFi:/#
root@MiFi:/# AP99 (ar7240 - Python) U-boot
/bin/ash: syntax error: unexpected word (expecting ")")
0_ddr_inroot@MiFi:/# ar7240_ddr_initial_config(137): python ddr init
/bin/ash: syntax error: unexpected word (expecting ")")
root@MiFi:/# #### TAP VALUE 1 = 0x8, 2 = 0x8 [0x2: 0xe]
root@MiFi:/# CPU_FREQ=400##DDR_FREQ=400##AHB_FREQ=200
DRAM:  6root@MiFi:/# DRAM:  64 MB
/bin/ash: DRAM:: not found
root@MiFi:/# Flash: 16 MB
/bin/ash: Flash:: not found
bad CRC,root@MiFi:/# *** Warning - bad CRC, using default environment
    seri/bin/ash: bin: not found
al
Out: root@MiFi:/#
root@MiFi:/# In:    serial
/bin/ash: In:: not found
serial
Nroot@MiFi:/# Out:   serial
7240_ene/bin/ash: Out:: not found
root@MiFi:/# Err:   serial
lize...
/bin/ash: Err:: not found
root@MiFi:/# Net:   ag7240_enet_initialize...
ddr Fetc/bin/ash: Net:: not found
root@MiFi:/# ag7240_get_ethaddr Fetching MAC Address from 0x9f01fc00
get_etha/bin/ash: ag7240_get_ethaddr: not found
root@MiFi:/# ag7240_get_ethaddr Fetching MAC Address from 0x9f01fc00
/bin/ash: ag7240_get_ethaddr: not found
root@MiFi:/# : cfg1 0xf cfg2 0x7014
root@MiFi:/# eth0: f4:ec:38:70:7b:98
/bin/ash:
: cfg1 eth0:: not found
root@MiFi:/# eth0 up
0x7214
/bin/ash: eth0: not found
root@MiFi:/# : cfg1 0xf cfg2 0x7214
root@MiFi:/# eth1: f4:ec:38:70:7b:99
resetti/bin/ash: eth1:: not found
root@MiFi:/# ATHRS26: resetting s26
/bin/ash: ATHRS26:: not found
s26 resroot@MiFi:/# ATHRS26: s26 reset done
eth1 up
/bin/ash: ATHRS26:: not found
root@MiFi:/# eth1 up
ning: et/bin/ash: eth1: not found
root@MiFi:/# eth0
ddresses/bin/ash: eth0: not found
root@MiFi:/# Warning: eth0 MAC addresses don't match:
> Address in SROM is         F4:EC:38:70:7B:98
> Address in environment is  40:16:FFFFFF9F:FFFFFFAB:FFFFFFE0:FFFFFF82
> , eth1
> Autobooting in 1 seconds press tt to abort
> ## Booting image at 9f020000 ...
>    Uncompressing Kernel Image ... OK
>
nel ...
> Starting kernel ...
>
>
>
l loader> OpenWrt kernel loader for AR7XXX/AR9XXX
> Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
> Looking for OpenWrt image... found at 0xbf022000
> Decompressing kernel... done!
> Starting kernel at 80060000...
>
> [    0.000000] Linux version 4.4.140 (cezary@eko.one.pl) (gcc version 5.4.0 (L
EDE GCC 5.4.0 r3785-ceea0ac) ) #0 Tue Jul 17 05:17:48 2018
> [    0.000000] bootconsole [early0] enabled
> [    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
> [    0.000000] SoC: Atheros AR7240 rev 2
> [    0.000000] Determined physical RAM map:
> [    0.000000]  memory: 04000000 @ 00000000 (usable)
> [    0.000000] Initrd not found or empty - disabling initrd
> [    0.000000] No valid device tree found, continuing without
> [    0.000000] Zone ranges:
> [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
> [    0.000000] Movable zone start for each node
> [    0.000000] Early memory node ranges
> [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
> [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff
]
> [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
> [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 3
2 bytes
> [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total p
ages: 16256
> [    0.000000] Kernel command line: board=TL-MR3220  console=ttyS0,115200 root
fstype=squashfs,jffs2 noinitrd
> [    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
> [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> [    0.000000] Writing ErrCtl register=00000000
> [    0.000000] Readback ErrCtl register=00000000
> [    0.000000] Memory: 59904K/65536K available (3130K kernel code, 162K rwdata
, 780K rodata, 336K init, 205K bss, 5632K reserved, 0K cma-reserved)
> [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [    0.000000] NR_IRQS:51
> [    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.
000MHz
  0.0000> [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max
_idle_ns: 9556302233 ns
> [    0.000013] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 107
37418237ns
> [    0.007894] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
> [    0.090597] pid_max: default: 32768 minimum: 301
> [    0.095386] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [    0.101996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes
)
> [    0.112825] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604462750000 ns
> [    0.122684] futex hash table entries: 256 (order: -1, 3072 bytes)
> [    0.130581] NET: Registered protocol family 16
[    0.1> [    0.137171] MIPS: machine is TP-LINK TL-MR3220
> [    0.577354] registering PCI controller with io_map_base unset
> [    1.593509] PCI host bridge to bus 0000:00
> [    1.597690] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
> [    1.604541] pci_bus 0000:00: root bus resource [io  0x0000]
> [    1.610109] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
> [    1.616880] pci_bus 0000:00: No busn resource found for root bus, will use
[bus 00-ff]
> [    1.624885] pci 0000:00:00.0: fixup device configuration
> [    1.632045] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64
bit]
> [    1.639401] pci 0000:00:00.0: using irq 40 for pin 1
> [    1.645580] clocksource: Switched to clocksource MIPS
> [    1.652591] NET: Registered protocol family 2
> [    1.658335] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
> [    1.665308] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> [    1.671735] TCP: Hash tables configured (established 1024 bind 1024)
   1.678> [    1.678241] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.6> [    1.684095] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> [    1.690795] NET: Registered protocol family 1
> [    1.701962] Crashlog allocated RAM at address 0x3f00000
> [    1.729029] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [    1.734868] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIOR
ITY) (c) 2001-2006 Red Hat, Inc.
> [    1.748331] io scheduler noop registered
> [    1.752265] io scheduler deadline registered (default)
    1.75> [    1.757832] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
> [    1.768357] console [ttyS0] disabled
[    1.7> [    1.791970] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1
2500000) is a 16550A
> [    1.800670] console [ttyS0] enabled
> [    1.800670] console [ttyS0] enabled
> [    1.807688] bootconsole [early0] disabled
[    1.8> [    1.807688] bootconsole [early0] disabled
> [    1.822712] m25p80 spi0.0: found mx25l12805d, expected m25p80
> [    1.828605] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
> [    1.835140] 5 tp-link partitions found on MTD device spi0.0
[    1.8> [    1.840806] Creating 5 MTD partitions on "spi0.0":
> [    1.845648] 0x000000000000-0x000000020000 : "u-boot"
> [    1.852589] 0x000000020000-0x000000170d84 : "kernel"
> [    1.859872] 0x000000170d84-0x000000ff0000 : "rootfs"
> [    1.867149] mtd: device 2 (rootfs) set to be root filesystem
[    1.8> [    1.872886] 1 squashfs-split partitions found on MTD device rootfs
    1.87> [    1.879186] 0x000000380000-0x000000ff0000 : "rootfs_data"
> [    1.886922] 0x000000ff0000-0x000001000000 : "art"
> [    1.893890] 0x000000020000-0x000000ff0000 : "firmware"
> [    1.926552] libphy: ag71xx_mdio: probed
> [    2.517074] ag71xx-mdio.0: Found an AR7240/AR9330 built-in switch
> [    2.559121] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
> [    3.149318] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004d
d041, driver=Generic PHY]
3.159499> [    3.159499] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
> [    3.168597] NET: Registered protocol family 10
> [    3.178486] NET: Registered protocol family 17
> [    3.183065] bridge: automatic filtering via arp/ip/ip6tables has been depre
cated. Update your scripts to load br_netfilter if you need this.
> [    3.195972] 8021q: 802.1Q VLAN Support v1.8
> [    3.202662] hctosys: unable to open rtc device (rtc0)
> [    3.213370] VFS: Mounted root (squashfs filesystem) readonly on device 31:2
.
> [    3.223288] Freeing unused kernel memory: 336K
> [    4.586545] init: Console is alive
[    4.5> [    4.590232] init: - watchdog -
> [    6.042457] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.1> [    6.133865] usbcore: registered new interface driver usbfs
> [    6.139610] usbcore: registered new interface driver hub
> [    6.145082] usbcore: registered new device driver usb
> [    6.157209] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [    6.165965] ehci-platform: EHCI generic platform driver
> [    6.174921] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [    6.183028] ohci-platform: OHCI generic platform driver
> [    6.188517] ohci-platform ohci-platform: Generic Platform OHCI controller
> [    6.195402] ohci-platform ohci-platform: new USB bus registered, assigned b
us number 1
> [    6.203487] ohci-platform ohci-platform: irq 3, io mem 0x1b000000
> [    6.270883] hub 1-0:1.0: USB hub found
> [    6.275072] hub 1-0:1.0: 1 port detected
> [    6.280213] kmodloader: done loading kernel modules from /etc/modules-boot.
d/*
> [    6.298072] init: - preinit -
> [    6.959215] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [    6.992931] random: procd: uninitialized urandom read (4 bytes read, 11 bit
s of entropy available)
ress the> Press the [f] key and hit [enter] to enter failsafe mode
> Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
> [    9.056976] eth0: link up (1000Mbps/Full duplex)
> [    9.061699] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [   10.327400] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
> [   10.339876] urandom-seed: Seed file not found (/etc/urandom.seed)
   10.58> [   10.587666] eth0: link down
> [   10.604148] procd: - early -
> [   10.608080] procd: - watchdog -
> [   11.301745] random: jshn: uninitialized urandom read (4 bytes read, 18 bits
of entropy available)
> [   11.421690] procd: - watchdog -
1.425188> [   11.425188] procd: - ubus -
> [   11.973493] random: ubusd: uninitialized urandom read (4 bytes read, 19 bit
s of entropy available)
> [   11.996066] random: ubusd: uninitialized urandom read (4 bytes read, 19 bit
s of entropy available)
> [   12.016002] random: ubusd: uninitialized urandom read (4 bytes read, 20 bit
s of entropy available)
> [   12.025104] random: ubusd: uninitialized urandom read (4 bytes read, 20 bit
s of entropy available)
> [   12.053405] random: ubusd: uninitialized urandom read (4 bytes read, 20 bit
s of entropy available)
> [   12.065775] random: ubusd: uninitialized urandom read (4 bytes read, 20 bit
s of entropy available)
> [   12.081218] random: ubusd: uninitialized urandom read (4 bytes read, 20 bit
s of entropy available)
> [   12.090577] random: ubusd: uninitialized urandom read (4 bytes read, 20 bit
s of entropy available)
> [   12.100221] procd: - init -
> Please press Enter to activate this console.
> [   12.647236] kmodloader: loading kernel modules from /etc/modules.d/*
> [   12.673211] usbcore: registered new interface driver cdc_wdm
[   12.6> [   12.687988] Loading modules backported from Linux version wt-2017-01-31-0-g
e882dff19e7f
> [   12.696125] Backport generated by backports.git backports-20160324-13-g24da
7d3c
> [   12.733661] nf_conntrack version 0.5.0 (941 buckets, 3764 max)
> [   12.867379] usbcore: registered new interface driver usbserial
> [   12.873394] usbcore: registered new interface driver usbserial_generic
> [   12.880198] usbserial: USB Serial support registered for generic
> [   12.957956] xt_time: kernel timezone is -0000
> [   12.970614] usbcore: registered new interface driver cdc_ether
> [   12.989342] usbcore: registered new interface driver cdc_ncm
> [   13.054894] usbcore: registered new interface driver huawei_cdc_ncm
> [   13.074846] ip_tables: (C) 2000-2006 Netfilter Core Team
> [   13.219860] PPP generic driver version 2.4.2
> [   13.248660] usbcore: registered new interface driver qmi_wwan
> [   13.258436] usbcore: registered new interface driver rndis_host
> [   13.278215] usbcore: registered new interface driver sierra
> [   13.283958] usbserial: USB Serial support registered for Sierra USB modem
> [   13.308530] usbcore: registered new interface driver sierra_net
> [   13.410441] usbcore: registered new interface driver option
> [   13.416296] usbserial: USB Serial support registered for GSM modem (1-port)
> [   13.437850] usbcore: registered new interface driver qcserial
> [   13.443771] usbserial: USB Serial support registered for Qualcomm USB modem
> [   13.503420] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
> [   13.514312] ath: phy0: Ignoring endianness difference in EEPROM magic bytes
.
> [   13.521514] ath: phy0: Enable LNA combining
> [   13.549502] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
> [   13.616125] kmodloader: done loading kernel modules from /etc/modules.d/*
> [   25.322937] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
> [   25.355728] jffs2_build_filesystem(): unlocking the mtd device... done.
> [   25.362403] jffs2_build_filesystem(): erasing all blocks after the end mark
er...
> [   31.730734] device eth0 entered promiscuous mode
> [   31.748717] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
> [   31.868519] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
> [   33.827001] eth0: link up (1000Mbps/Full duplex)
> [   33.831709] br-lan: port 1(eth0) entered forwarding state
> [   33.837233] br-lan: port 1(eth0) entered forwarding state
> [   33.864381] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
> [   33.987210] eth1: link up (100Mbps/Full duplex)
33.9918> [   33.991812] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
35.8356> [   35.835609] br-lan: port 1(eth0) entered forwarding state
> [   37.307115] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [   37.381320] device wlan0 entered promiscuous mode
> [   40.805178] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> [   40.811853] br-lan: port 2(wlan0) entered forwarding state
> [   40.817470] br-lan: port 2(wlan0) entered forwarding state
> [   42.815712] br-lan: port 2(wlan0) entered forwarding state
> [   61.341880] random: nonblocking pool is initialized
>
>
>
> BusyBox v1.25.1 () built-in shell (ash)
>
_______>      _________
>     /        /\      _    ___ ___  ___
>    /  LE    /  \    | |  | __|   \| __|
>   /    DE  /    \   | |__| _|| |) | _|
>  /________/  LE  \  |____|___|___/|___|                      lede-project.org
>  \        \   DE /
>   \    LE  \    /  -----------------------------------------------------------
>    \  DE    \  /    Reboot (17.01-SNAPSHOT, r3925-79c8f2f50b)
>     \________\/    -----------------------------------------------------------
>
-------->  -----------------------------------------------------------------------------
>  |                                                                           |
>  | Build time: 2018-07-18 15:53 CEST                                         |
>  |                                                                           |
>  | Cezary Jackiewicz (obsy), http://eko.one.pl                               |
>  |                                                                           |
>  -----------------------------------------------------------------------------
>  | Machine: TP-Link TL-MR3220 v1                                             |
>  | Uptime: 0d, 00:01:42                                                      |
>  | Load: 1.64 0.67 0.25                                                      |
>  | Flash: total: 29.4MB, free: 29.4MB, used: 0%                              |
>  | Memory: total: 58.8MB, free: 46.7MB, used: 20%                            |
| WAN: 1>  | WAN: 192.168.88.251, proto: dhcp                                          |
>  | LAN: 192.168.11.1, leases: 0                                              |
>  | radio0: mode: ap, ssid: mifi-707b97, channel: 11, conn: 0                 |
>  -----------------------------------------------------------------------------
> root@MiFi:/# [  112.246338] done.
> [  112.248373] jffs2: notice: (1065) jffs2_build_xattr_subsystem: complete bui
lding xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead
, 0 orphan) found.
> [  116.005619] usb 1-1: new full-speed USB device number 2 using ohci-platform
> [  117.042402] usb 1-1: USB disconnect, device number 2
> [  121.485621] usb 1-1: new full-speed USB device number 3 using ohci-platform
> [  121.988338] option 1-1:1.0: GSM modem (1-port) converter detected
> [  121.994942] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
> [  122.002705] option 1-1:1.1: GSM modem (1-port) converter detected
> [  122.009366] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
> [  122.016958] option 1-1:1.2: GSM modem (1-port) converter detected
> [  122.023497] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
>
> root@MiFi:/#

4 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,039

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

Ależ wykrywa, sam to zacytowałeś:

> [  121.988338] option 1-1:1.0: GSM modem (1-port) converter detected
> [  121.994942] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
> [  122.002705] option 1-1:1.1: GSM modem (1-port) converter detected
> [  122.009366] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
> [  122.016958] option 1-1:1.2: GSM modem (1-port) converter detected
> [  122.023497] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2

PS. nie wklejaj tekstu myszą do konsoli bo się bzdury robią.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

5 Odpowiedź przez maly310 (edytowany przez maly310 2018-12-01 21:34:24)

  • Zarejestrowany: 2012-11-03
  • Posty: 16

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

jak wspomniałem, wykrywa na MiFi a na LEDE już nie.

ok. bede pamiętał o tym kopiowaniu.

6 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,039

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

Zainstaluj jeszcze raz lede, podłącz modem i pokaż wynik polecenia

cat /sys/kernel/debug/usb/devices

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

7 Odpowiedź przez maly310

  • Zarejestrowany: 2012-11-03
  • Posty: 16

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

na lede kompletnie nic nie zwraca to zapytanie, tak jakby USB nie działało.

root@LEDE:/# cat /sys/kernel/debug/usb/devices
root@LEDE:/#



root@MiFi:/# cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12   MxCh= 1
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0.........................i tak dalej

8 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,039

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

Masz zainstalowane kmod-usb-ohci na tym lede?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

9 Odpowiedź przez maly310

  • Zarejestrowany: 2012-11-03
  • Posty: 16

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

-tego nie było, już jest zainstalowany. ale modem jest w trybie CD-ROMu

-doinstalowałem jeszcze usb-modeswitch ; kmod-usb-net-cdc-ether ; sdparm (błąd instalacji) ; kmod-usb-serial-option

-Już modem jest widoczny smile

10 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,039

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

kmod-usb-net-cdc-ether  jest zbędny jak nie masz hilinka.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

11 Odpowiedź przez maly310 (edytowany przez maly310 2018-12-01 23:20:48)

  • Zarejestrowany: 2012-11-03
  • Posty: 16

Odp: Nie wykrywa modemu OW150P rev 2.0 (podróba TP-MR3220 V1)

już mu nie zaszkodzi dodatkowy pakiet. Cezary, bardzo dziękuję za pomoc.
Dziś już Tobie i sobie dam na wstrzymanie ale został mi jeszcze Mikrotik do przerobienia wink

tym sposobem udało mi się nawet na starym garygole1622 uruchomić modem.