• Zarejestrowany: 2018-07-12
  • Posty: 7

Temat: Easy Box 802 OpenWRT - print server + repeater

Witajcie
Od kilku dni próbuję ustawić router EasyBox 802 z alle... tak, żeby:
Internet u mnie dostarczany z dekodera Telpol jest na port WAN w routerze Pentagram Cerberus P6361 podający z portu LAN sygnał na komputer stacjonarny na masce 255.255.255.0 w adresach 192.168.1.100-250.
Router EasyBox (192.168.2.1) połączyłem po wifi z Pentagramem jako Klient wg poradnika na YT (repeater) tak, że - PC podłączony RJ45 pod LAN Easybox otrzymuje internet. Drukarka podłączona pod port USB EasyBox drukuje (drukarka przypisana jako 192.168.1.102). Po odpięciu RJ45 między PC a EasyBox i podpięciu za jego pomocą PC i Pentagrama .... drukarka nie drukuje.
W zamierzeniu - Pentagram ma zostać połączony z dekoderem Telpol i po RJ45 ma przekazać "internet" do PC.
EasyBox ma stać w drugim pokoju i być połączony po wifi z Pentagram i udostępniać w sieci drukarkę.
Już nie mam pomysłów jak to ustawić - pomożecie?

2 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,013

Odp: Easy Box 802 OpenWRT - print server + repeater

Jako klient czy jako repeater (bo to jest różnica)?

Jeżeli faktycznie jako repeater to powinieneś odwołać się do drukarki po ip routera, po ip które on otrzymał od pentagrama. Nie  ten adres który masz na lanie w easyboxie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

3 Odpowiedź przez 9tysiecy

  • Zarejestrowany: 2018-01-30
  • Posty: 724

Odp: Easy Box 802 OpenWRT - print server + repeater

Przeczytaj to https://eko.one.pl/?p=openwrt-sta#konfiguracja
Oraz
https://eko.one.pl/?p=openwrt-sta#dostpdoroutera

4 Odpowiedź przez BROWAReq

  • Zarejestrowany: 2018-07-12
  • Posty: 7

Odp: Easy Box 802 OpenWRT - print server + repeater

Cezary napisał/a:

Jako klient czy jako repeater (bo to jest różnica)?

Jeżeli faktycznie jako repeater to powinieneś odwołać się do drukarki po ip routera, po ip które on otrzymał od pentagrama. Nie  ten adres który masz na lanie w easyboxie.

Przepraszam, że tak późno ale nie było mnie wczoraj. Właśnie wg filmiku na YT https://www.youtube.com/watch?v=RgeNnTbVqk0 jest jako klient. I tylko w takiej formie działa. Nie widzę tam opcji do wybrania jako repeater czy bridge - jako punkt przekaźnikowy nie działało.

5 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,013

Odp: Easy Box 802 OpenWRT - print server + repeater

Odblokuj sobie w easybox na wanie port 9100 i podłącz się do ip jakie easybox dostał na wanie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

6 Odpowiedź przez andix84

  • Skąd: Toruń
  • Zarejestrowany: 2014-11-17
  • Posty: 48

Odp: Easy Box 802 OpenWRT - print server + repeater

Ostatnio coś takiego skonfigurowałem na gargoyle. Wystarczy router ustawić jako most bezprzewodowy i podpiąć drukarkę do usb. Instalując drukarkę dodajesz nowy port TCP/IP z adresem takim jaki ma w sieci lokalnej router - działa.

7 Odpowiedź przez BROWAReq (edytowany przez BROWAReq 2018-07-16 20:30:58)

  • Zarejestrowany: 2018-07-12
  • Posty: 7

Odp: Easy Box 802 OpenWRT - print server + repeater

Szkoda, że nie mogę screenów wstawić - pokazałbym ustawienia.
Port nasłuchu mam w WAN ustawiony na 9100.
Sieć główna - PENTAGRAM (ta do wzmocnienia wg filmiku) - rozsyła adresy 192.168.1.100-250
Wg YT ustawiłem EasyBox jako sieć Pentagram2 - jej adresy są z puli 192.168.2.xxx - przekazuje internet zarówno po wi-fi jak i po LAN, gdy jest połączony do PC.
Przy połączeniu PC z EasyBox za pomocą LAN - mogę wejść na jego "panel" na adresie 192.168.2.1 oraz także na adresie, który przypisał mu PENTAGRAM - aktualnie 192.168.1.101 (choć jak rozumiem, za każdym razem może być inny? )
Drukarce ustawiłem ten właśnie port i drukuje. Gdy odłączam LAN od EasyBox i wpinam go do PENTAGRAM - co logiczne na 192.168.2.1 nie mogę wejść ale co mnie już zdziwiło na 192.168.1.101 też nie. Drukarka również nie drukuje... wrrr
Jako most mogę ustawić PENTAGRAM - tam mam biało na czarnym do wyboru dwie opcje - AP oraz Most - w EB hmm

8 Odpowiedź przez BROWAReq

  • Zarejestrowany: 2018-07-12
  • Posty: 7

Odp: Easy Box 802 OpenWRT - print server + repeater

Log Systemowy:

 Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.772000] usbcore: registered new interface driver sierra
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.776000] usbserial: USB Serial support registered for Sierra USB modem
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.792000] usbcore: registered new interface driver sierra_net
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.808000] usbcore: registered new interface driver cdc_mbim
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.820000] usbcore: registered new interface driver option
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.824000] usbserial: USB Serial support registered for GSM modem (1-port)
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.840000] usbcore: registered new interface driver qcserial
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.844000] usbserial: USB Serial support registered for Qualcomm USB modem
Mon Jul 16 20:22:14 2018 kern.warn kernel: [   29.892000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
Mon Jul 16 20:22:14 2018 kern.err kernel: [   29.896000] rt2800pci 0000:00:0e.0: failed to load eeprom property
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.904000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT2860.eeprom'.
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.916000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2860, rev 0103 detected
Mon Jul 16 20:22:14 2018 kern.info kernel: [   29.924000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0001 detected
Mon Jul 16 20:22:14 2018 kern.debug kernel: [   29.932000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Mon Jul 16 20:22:21 2018 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Mon Jul 16 20:22:22 2018 daemon.err block: /dev/mtdblock5 is already mounted
Mon Jul 16 20:22:25 2018 authpriv.info dropbear[1149]: Not backgrounding
Mon Jul 16 20:22:25 2018 lpr.err p9100d[1158]: bind: Cannot assign requested address
Mon Jul 16 20:22:25 2018 lpr.err p9100d[1158]: accept: Bad file descriptor
Mon Jul 16 20:22:29 2018 daemon.err uhttpd[1204]: socket(): Address family not supported by protocol
Mon Jul 16 20:22:29 2018 daemon.err uhttpd[1204]: socket(): Address family not supported by protocol
Mon Jul 16 20:22:34 2018 kern.info kernel: [   54.780000] device eth0.1 entered promiscuous mode
Mon Jul 16 20:22:34 2018 kern.info kernel: [   54.784000] device eth0 entered promiscuous mode
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'lan' is enabled
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'lan' is setting up now
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'lan' is now up
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'loopback' is enabled
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'loopback' is setting up now
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'loopback' is now up
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Network device 'lo' link is up
Mon Jul 16 20:22:34 2018 daemon.notice netifd: Interface 'loopback' has link connectivity 
Mon Jul 16 20:22:35 2018 kern.info kernel: [   56.392000] br-lan: port 1(eth0.1) entered forwarding state
Mon Jul 16 20:22:35 2018 kern.info kernel: [   56.396000] br-lan: port 1(eth0.1) entered forwarding state
Mon Jul 16 20:22:35 2018 daemon.notice netifd: Network device 'eth0' link is up
Mon Jul 16 20:22:35 2018 daemon.notice netifd: VLAN 'eth0.1' link is up
Mon Jul 16 20:22:35 2018 daemon.notice netifd: Bridge 'br-lan' link is up
Mon Jul 16 20:22:35 2018 daemon.notice netifd: Interface 'lan' has link connectivity 
Mon Jul 16 20:22:36 2018 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Mon Jul 16 20:22:38 2018 kern.info kernel: [   58.400000] br-lan: port 1(eth0.1) entered forwarding state
Mon Jul 16 20:22:41 2018 daemon.notice netifd: radio0 (1248): command failed: Operation not supported (-122)
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led wifi
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led usb
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led internet
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led fxo
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led fxs1
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led fxs2
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led message
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led power1
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led voice1
Mon Jul 16 20:22:46 2018 user.emerg syslog: setting up led voice2
Mon Jul 16 20:22:48 2018 daemon.notice netifd: radio0 (1248): Configuration file: /var/run/hostapd-phy0.conf
Mon Jul 16 20:22:48 2018 kern.info kernel: [   68.804000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
Mon Jul 16 20:22:48 2018 kern.info kernel: [   69.260000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
Mon Jul 16 20:22:48 2018 daemon.notice netifd: radio0 (1248): wlan0-1: interface state UNINITIALIZED->COUNTRY_UPDATE
Mon Jul 16 20:22:48 2018 kern.info kernel: [   69.372000] device wlan0-1 entered promiscuous mode
Mon Jul 16 20:22:48 2018 daemon.notice netifd: radio0 (1248): Using interface wlan0-1 with hwaddr 00:0c:43:28:60:01 and ssid "Pentagram2"
Mon Jul 16 20:22:52 2018 daemon.info procd: - init complete -
Mon Jul 16 20:22:52 2018 daemon.notice netifd: radio0 (1248): wlan0-1: interface state COUNTRY_UPDATE->ENABLED
Mon Jul 16 20:22:52 2018 daemon.notice netifd: radio0 (1248): wlan0-1: AP-ENABLED 
Mon Jul 16 20:22:53 2018 daemon.notice netifd: radio0 (1248): Successfully initialized wpa_supplicant
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq[1553]: started, version 2.73 cachesize 150
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq[1553]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq[1553]: DNS service limited to local subnets
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq-dhcp[1553]: DHCP, IP range 192.168.2.100 -- 192.168.2.249, lease time 12h
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq[1553]: using local addresses only for domain lan
Mon Jul 16 20:22:54 2018 daemon.warn dnsmasq[1553]: no servers found in /tmp/resolv.conf.auto, will retry
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq[1553]: read /etc/hosts - 1 addresses
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq[1553]: read /tmp/hosts/dhcp - 1 addresses
Mon Jul 16 20:22:54 2018 daemon.info dnsmasq-dhcp[1553]: read /etc/ethers - 0 addresses
Mon Jul 16 20:22:58 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 
Mon Jul 16 20:22:58 2018 daemon.info dnsmasq-dhcp[1553]: DHCPACK(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 BROWAReq-komp
Mon Jul 16 20:22:58 2018 kern.info kernel: [   79.316000] wlan0: authenticate with c8:3a:35:44:bd:f0
Mon Jul 16 20:22:58 2018 kern.info kernel: [   79.332000] wlan0: send auth to c8:3a:35:44:bd:f0 (try 1/3)
Mon Jul 16 20:22:58 2018 kern.info kernel: [   79.336000] wlan0: authenticated
Mon Jul 16 20:22:58 2018 kern.info kernel: [   79.352000] wlan0: associate with c8:3a:35:44:bd:f0 (try 1/3)
Mon Jul 16 20:22:58 2018 kern.info kernel: [   79.364000] wlan0: RX AssocResp from c8:3a:35:44:bd:f0 (capab=0x411 status=0 aid=1)
Mon Jul 16 20:22:58 2018 kern.info kernel: [   79.368000] wlan0: associated
Mon Jul 16 20:22:59 2018 daemon.notice netifd: Network device 'wlan0' link is up
Mon Jul 16 20:22:59 2018 daemon.notice netifd: Interface 'wwan' is enabled
Mon Jul 16 20:22:59 2018 daemon.notice netifd: Interface 'wwan' has link connectivity 
Mon Jul 16 20:22:59 2018 daemon.notice netifd: Interface 'wwan' is setting up now
Mon Jul 16 20:23:00 2018 daemon.notice netifd: wwan (1672): udhcpc (v1.23.2) started
Mon Jul 16 20:23:01 2018 daemon.notice netifd: wwan (1672): Sending discover...
Mon Jul 16 20:23:02 2018 daemon.notice netifd: wwan (1672): Sending select for 192.168.1.101...
Mon Jul 16 20:23:02 2018 daemon.notice netifd: wwan (1672): Lease of 192.168.1.101 obtained, lease time 86400
Mon Jul 16 20:23:03 2018 kern.info kernel: [   83.456000] br-lan: port 2(wlan0-1) entered forwarding state
Mon Jul 16 20:23:03 2018 kern.info kernel: [   83.460000] br-lan: port 2(wlan0-1) entered forwarding state
Mon Jul 16 20:23:03 2018 daemon.notice netifd: Network device 'wlan0-1' link is up
Mon Jul 16 20:23:03 2018 daemon.notice netifd: Interface 'wwan' is now up
Mon Jul 16 20:23:03 2018 daemon.info dnsmasq[1553]: reading /tmp/resolv.conf.auto
Mon Jul 16 20:23:03 2018 daemon.info dnsmasq[1553]: using local addresses only for domain lan
Mon Jul 16 20:23:03 2018 daemon.info dnsmasq[1553]: using nameserver 192.168.200.250#53
Mon Jul 16 20:23:03 2018 daemon.info dnsmasq[1553]: using nameserver 192.168.0.250#53
Mon Jul 16 20:23:05 2018 kern.info kernel: [   85.464000] br-lan: port 2(wlan0-1) entered forwarding state
Mon Jul 16 20:23:07 2018 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Mon Jul 16 20:23:14 2018 user.notice adblock[1783] info : adblock service started due to 'ifup' of 'wwan' interface
Mon Jul 16 20:23:15 2018 user.notice adblock[1881] info : adblock is currently disabled, please set adblock.global.adb_enabled=1' to use this service
Mon Jul 16 21:07:31 2018 lpr.notice p9100d[10822]: Connection from 192.168.2.156 port 64260 accepted
Mon Jul 16 21:07:32 2018 lpr.notice p9100d[10822]: Finished job: 224014/224014 bytes sent to printer, 0/0 bytes sent to network
Mon Jul 16 21:09:22 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 IEEE 802.11: authenticated
Mon Jul 16 21:09:22 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 IEEE 802.11: associated (aid 1)
Mon Jul 16 21:09:22 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: pairwise key handshake completed (RSN)
Mon Jul 16 21:09:25 2018 daemon.info dnsmasq-dhcp[1553]: DHCPDISCOVER(br-lan) 78:02:f8:2f:3a:a0 
Mon Jul 16 21:09:25 2018 daemon.info dnsmasq-dhcp[1553]: DHCPOFFER(br-lan) 192.168.2.190 78:02:f8:2f:3a:a0 
Mon Jul 16 21:09:25 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.2.190 78:02:f8:2f:3a:a0 
Mon Jul 16 21:09:25 2018 daemon.info dnsmasq-dhcp[1553]: DHCPACK(br-lan) 192.168.2.190 78:02:f8:2f:3a:a0 RedmiPro-Redmi
Mon Jul 16 21:11:12 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: group key handshake completed (RSN)
Mon Jul 16 21:13:37 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.1.103 e0:3f:49:82:bf:92 
Mon Jul 16 21:13:37 2018 daemon.info dnsmasq-dhcp[1553]: DHCPNAK(br-lan) 192.168.1.103 e0:3f:49:82:bf:92 wrong address
Mon Jul 16 21:13:37 2018 daemon.info dnsmasq-dhcp[1553]: DHCPDISCOVER(br-lan) e0:3f:49:82:bf:92 
Mon Jul 16 21:13:37 2018 daemon.info dnsmasq-dhcp[1553]: DHCPOFFER(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 
Mon Jul 16 21:13:37 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 
Mon Jul 16 21:13:37 2018 daemon.info dnsmasq-dhcp[1553]: DHCPACK(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 BROWAReq-komp
Mon Jul 16 21:13:47 2018 lpr.notice p9100d[10822]: Connection from 192.168.2.156 port 64900 accepted
Mon Jul 16 21:13:47 2018 lpr.notice p9100d[10822]: Finished job: 224009/224009 bytes sent to printer, 0/0 bytes sent to network
Mon Jul 16 21:16:44 2018 daemon.notice netifd: Interface 'wwan' is disabled
Mon Jul 16 21:16:44 2018 daemon.notice netifd: Interface 'wwan' has link connectivity loss
Mon Jul 16 21:16:44 2018 kern.info kernel: [ 1005.448000] device wlan0-1 left promiscuous mode
Mon Jul 16 21:16:44 2018 kern.info kernel: [ 1005.448000] br-lan: port 2(wlan0-1) entered disabled state
Mon Jul 16 21:16:45 2018 daemon.notice netifd: wwan (1672): Received SIGTERM
Mon Jul 16 21:16:45 2018 daemon.notice netifd: Interface 'wwan' is now down
Mon Jul 16 21:16:45 2018 daemon.warn dnsmasq[1553]: no servers found in /tmp/resolv.conf.auto, will retry
Mon Jul 16 21:16:46 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 
Mon Jul 16 21:16:46 2018 daemon.info dnsmasq-dhcp[1553]: DHCPACK(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 BROWAReq-komp
Mon Jul 16 21:16:46 2018 kern.info kernel: [ 1007.364000] wlan0: deauthenticating from c8:3a:35:44:bd:f0 by local choice (Reason: 3=DEAUTH_LEAVING)
Mon Jul 16 21:16:47 2018 daemon.notice netifd: Interface 'wan' is enabled
Mon Jul 16 21:16:49 2018 daemon.notice netifd: radio0 (12806): command failed: Operation not supported (-122)
Mon Jul 16 21:16:52 2018 daemon.notice netifd: radio0 (12806): Configuration file: /var/run/hostapd-phy0.conf
Mon Jul 16 21:16:52 2018 kern.info kernel: [ 1013.740000] device wlan0-1 entered promiscuous mode
Mon Jul 16 21:16:52 2018 daemon.notice netifd: radio0 (12806): wlan0-1: interface state UNINITIALIZED->COUNTRY_UPDATE
Mon Jul 16 21:16:53 2018 daemon.notice netifd: radio0 (12806): Using interface wlan0-1 with hwaddr 00:0c:43:28:60:01 and ssid "Pentagram2"
Mon Jul 16 21:16:55 2018 daemon.notice netifd: radio0 (12806): wlan0-1: interface state COUNTRY_UPDATE->ENABLED
Mon Jul 16 21:16:55 2018 daemon.notice netifd: radio0 (12806): wlan0-1: AP-ENABLED 
Mon Jul 16 21:16:55 2018 daemon.notice netifd: radio0 (12806): Successfully initialized wpa_supplicant
Mon Jul 16 21:16:57 2018 daemon.notice netifd: Interface 'wwan' is enabled
Mon Jul 16 21:16:58 2018 kern.info kernel: [ 1019.092000] wlan0: authenticate with c8:3a:35:44:bd:f0
Mon Jul 16 21:16:58 2018 kern.info kernel: [ 1019.104000] wlan0: send auth to c8:3a:35:44:bd:f0 (try 1/3)
Mon Jul 16 21:16:58 2018 kern.info kernel: [ 1019.112000] wlan0: authenticated
Mon Jul 16 21:16:58 2018 kern.info kernel: [ 1019.120000] wlan0: associate with c8:3a:35:44:bd:f0 (try 1/3)
Mon Jul 16 21:16:58 2018 kern.info kernel: [ 1019.128000] wlan0: RX AssocResp from c8:3a:35:44:bd:f0 (capab=0x411 status=0 aid=1)
Mon Jul 16 21:16:58 2018 kern.info kernel: [ 1019.132000] wlan0: associated
Mon Jul 16 21:16:58 2018 daemon.notice netifd: Network device 'wlan0' link is up
Mon Jul 16 21:16:58 2018 daemon.notice netifd: Interface 'wwan' has link connectivity 
Mon Jul 16 21:16:58 2018 daemon.notice netifd: Interface 'wwan' is setting up now
Mon Jul 16 21:16:59 2018 daemon.notice netifd: wwan (13108): udhcpc (v1.23.2) started
Mon Jul 16 21:16:59 2018 daemon.notice netifd: wwan (13108): Sending discover...
Mon Jul 16 21:17:01 2018 daemon.notice netifd: wwan (13108): Sending select for 192.168.1.101...
Mon Jul 16 21:17:01 2018 daemon.notice netifd: wwan (13108): Lease of 192.168.1.101 obtained, lease time 86400
Mon Jul 16 21:17:01 2018 kern.info kernel: [ 1022.284000] br-wan: port 1(wlan0-1) entered forwarding state
Mon Jul 16 21:17:01 2018 kern.info kernel: [ 1022.288000] br-wan: port 1(wlan0-1) entered forwarding state
Mon Jul 16 21:17:01 2018 daemon.notice netifd: Network device 'wlan0-1' link is up
Mon Jul 16 21:17:01 2018 daemon.notice netifd: Bridge 'br-wan' link is up
Mon Jul 16 21:17:01 2018 daemon.notice netifd: Interface 'wan' has link connectivity 
Mon Jul 16 21:17:01 2018 daemon.notice netifd: Interface 'wan' is setting up now
Mon Jul 16 21:17:01 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 IEEE 802.11: authenticated
Mon Jul 16 21:17:01 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 IEEE 802.11: associated (aid 1)
Mon Jul 16 21:17:01 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: pairwise key handshake completed (RSN)
Mon Jul 16 21:17:02 2018 daemon.notice netifd: Interface 'wwan' is now up
Mon Jul 16 21:17:02 2018 daemon.info dnsmasq[1553]: reading /tmp/resolv.conf.auto
Mon Jul 16 21:17:02 2018 daemon.info dnsmasq[1553]: using local addresses only for domain lan
Mon Jul 16 21:17:02 2018 daemon.info dnsmasq[1553]: using nameserver 192.168.200.250#53
Mon Jul 16 21:17:02 2018 daemon.info dnsmasq[1553]: using nameserver 192.168.0.250#53
Mon Jul 16 21:17:02 2018 daemon.notice netifd: wan (13192): udhcpc (v1.23.2) started
Mon Jul 16 21:17:03 2018 daemon.notice netifd: wan (13192): Sending discover...
Mon Jul 16 21:17:03 2018 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Mon Jul 16 21:17:03 2018 kern.info kernel: [ 1024.292000] br-wan: port 1(wlan0-1) entered forwarding state
Mon Jul 16 21:17:06 2018 daemon.notice netifd: wan (13192): Sending discover...
Mon Jul 16 21:17:07 2018 user.notice adblock[13186] info : adblock service started due to 'ifup' of 'wwan' interface
Mon Jul 16 21:17:09 2018 daemon.notice netifd: wan (13192): Sending discover...
Mon Jul 16 21:17:09 2018 user.notice adblock[13336] info : adblock is currently disabled, please set adblock.global.adb_enabled=1' to use this service
Mon Jul 16 21:17:46 2018 lpr.notice p9100d[10822]: Connection from 192.168.2.156 port 65151 accepted
Mon Jul 16 21:17:47 2018 lpr.notice p9100d[10822]: Finished job: 223760/223760 bytes sent to printer, 0/0 bytes sent to network
Mon Jul 16 21:20:20 2018 lpr.notice p9100d[10822]: Connection from 192.168.2.156 port 65268 accepted
Mon Jul 16 21:20:20 2018 lpr.notice p9100d[10822]: Finished job: 223912/223912 bytes sent to printer, 0/0 bytes sent to network
Mon Jul 16 21:24:59 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.1.103 e0:3f:49:82:bf:92 
Mon Jul 16 21:24:59 2018 daemon.info dnsmasq-dhcp[1553]: DHCPNAK(br-lan) 192.168.1.103 e0:3f:49:82:bf:92 wrong address
Mon Jul 16 21:24:59 2018 daemon.info dnsmasq-dhcp[1553]: DHCPDISCOVER(br-lan) e0:3f:49:82:bf:92 
Mon Jul 16 21:24:59 2018 daemon.info dnsmasq-dhcp[1553]: DHCPOFFER(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 
Mon Jul 16 21:24:59 2018 daemon.info dnsmasq-dhcp[1553]: DHCPREQUEST(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 
Mon Jul 16 21:24:59 2018 daemon.info dnsmasq-dhcp[1553]: DHCPACK(br-lan) 192.168.2.156 e0:3f:49:82:bf:92 BROWAReq-komp
Mon Jul 16 21:25:04 2018 lpr.notice p9100d[10822]: Connection from 192.168.2.156 port 49275 accepted
Mon Jul 16 21:25:04 2018 lpr.notice p9100d[10822]: Finished job: 223911/223911 bytes sent to printer, 0/0 bytes sent to network
Mon Jul 16 21:26:55 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: group key handshake completed (RSN)
Mon Jul 16 21:36:13 2018 kern.err kernel: [ 2173.936000] eth0: tx ring full
Mon Jul 16 21:36:55 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: group key handshake completed (RSN)
Mon Jul 16 21:46:55 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: group key handshake completed (RSN)
Mon Jul 16 21:56:55 2018 daemon.info hostapd: wlan0-1: STA 78:02:f8:2f:3a:a0 WPA: group key handshake completed (RSN)

Log Jądra:

 [    0.000000] Linux version 3.18.29 (buildbot@node476.intranet) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49261) ) #25 Tue May 31 20:20:34 CEST 2016
[    0.000000] SoC: Danube rev 1.5
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
[    0.000000] MIPS: machine is ARV752DPW - EasyBOX 802
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 804262f0, node_mem_map 81007020
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0003c008
[    0.000000] Readback ErrCtl register=0003c008
[    0.000000] Memory: 60144K/65536K available (3437K kernel code, 147K rwdata, 768K rodata, 172K init, 194K bss, 5392K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 333MHz
[    0.040000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.056000] pinctrl core: initialized pinctrl subsystem
[    0.064000] NET: Registered protocol family 16
[    0.076000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.080000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[    0.088000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.092000]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.096000]   IO 0x000000001ae00000..0x000000001affffff
[    0.112000] usbcore: registered new interface driver usbfs
[    0.116000] usbcore: registered new interface driver hub
[    0.120000] usbcore: registered new device driver usb
[    0.124000] PCI host bridge to bus 0000:00
[    0.128000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.132000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.136000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.140000] pci 0000:00:0e.0: [1814:0601] type 00 class 0x028000
[    0.140000] pci 0000:00:0e.0: reg 0x10: [mem 0xffff0000-0xffffffff]
[    0.140000] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold
[    0.140000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.140000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[    0.144000] Switched to clocksource MIPS
[    0.148000] NET: Registered protocol family 2
[    0.156000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.164000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.168000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.176000] TCP: reno registered
[    0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.184000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.192000] NET: Registered protocol family 1
[    0.196000] PCI: CLS 0 bytes, default 32
[    0.196000] gptu: totally 6 16-bit timers/counters
[    0.200000] gptu: misc_register on minor 63
[    0.204000] gptu: succeeded to request irq 126
[    0.212000] gptu: succeeded to request irq 127
[    0.216000] gptu: succeeded to request irq 128
[    0.220000] gptu: succeeded to request irq 129
[    0.224000] gptu: succeeded to request irq 130
[    0.228000] gptu: succeeded to request irq 131
[    0.240000] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[    0.244000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[    0.252000] ralink,eeprom ralink_eep: using RT2860.eeprom as eeprom
[    0.260000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.272000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.276000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.316000] msgmni has been set to 117
[    0.324000] io scheduler noop registered
[    0.328000] io scheduler deadline registered (default)
[    0.336000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.344000] console [ttyLTQ0] enabled
[    0.352000] bootconsole [early0] disabled
[    0.360000] lantiq nor flash device: 00800000 at 10000000
[    0.368000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.376000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.380000]   Amd/Fujitsu Extended Query version 1.1.
[    0.384000] number of CFI chips: 1
[    0.388000] 4 ofpart partitions found on MTD device ltq_nor
[    0.392000] Creating 4 MTD partitions on "ltq_nor":
[    0.400000] 0x000000000000-0x000000010000 : "uboot"
[    0.404000] 0x000000010000-0x000000020000 : "uboot_env"
[    0.412000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.480000] 2 uimage-fw partitions found on MTD device firmware
[    0.484000] 0x000000020000-0x00000019611e : "kernel"
[    0.488000] 0x00000019611e-0x0000007f0000 : "rootfs"
[    0.496000] mtd: device 4 (rootfs) set to be root filesystem
[    0.500000] 1 squashfs-split partitions found on MTD device rootfs
[    0.504000] 0x000000750000-0x0000007f0000 : "rootfs_data"
[    0.576000] 0x0000007f0000-0x000000800000 : "board_config"
[    0.612000] libphy: ltq_mii: probed
[    0.704000] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
[    0.708000] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[    0.720000] wdt 1f8803f0.watchdog: Init done
[    0.728000] TCP: cubic registered
[    0.728000] NET: Registered protocol family 17
[    0.732000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.744000] Bridge firewalling registered
[    0.748000] 8021q: 802.1Q VLAN Support v1.8
[    0.760000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    0.780000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.784000] Freeing unused kernel memory: 172K (80445000 - 80470000)
[    3.832000] init: Console is alive
[    3.836000] init: - watchdog -
[    8.332000] exFAT: Version 1.2.9
[    8.392000] SCSI subsystem initialized
[    8.404000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.412000] ehci-platform: EHCI generic platform driver
[    8.428000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[    8.936000] IFXUSB: USB core #0 soft-reset
[    9.140000] IFXUSB: USB core #0 soft-reset
[    9.140000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    9.148000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
[    9.152000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[    9.160000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[    9.164000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
[    9.172000] IFXUSB: Init: Power Port (0)
[    9.180000] hub 1-0:1.0: USB hub found
[    9.180000] hub 1-0:1.0: 1 port detected
[    9.184000] ifxusb_hcd ifxusb_hcd: requested GPIO 464
[    9.196000] usbcore: registered new interface driver usb-storage
[    9.556000] usb 1-1: new high-speed USB device number 2 using ifxusb_hcd
[    9.748000] hub 1-1:1.0: USB hub found
[    9.752000] hub 1-1:1.0: 4 ports detected
[    9.980000] random: nonblocking pool is initialized
[   10.032000] usb 1-1.1: new high-speed USB device number 3 using ifxusb_hcd
[   10.192000] init: - preinit -
[   14.916000] mount_root: loading kmods from internal overlay
[   16.216000] jffs2: notice: (327) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   16.232000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   16.244000] block: extroot: not configured
[   16.508000] jffs2: notice: (324) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   16.524000] mount_root: loading kmods from internal overlay
[   17.280000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   17.292000] block: extroot: not configured
[   17.300000] mount_root: switching to jffs2 overlay
[   17.380000] procd: - early -
[   17.380000] procd: - watchdog -
[   18.612000] procd: - ubus -
[   19.636000] procd: - init -
[   28.524000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[   28.524000] 
Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[   28.600000] NET: Registered protocol family 8
[   28.604000] NET: Registered protocol family 20
[   28.648000] gre: GRE over IPv4 demultiplexor driver
[   28.656000] ip_gre: GRE over IPv4 tunneling driver
[   28.684000] PPP generic driver version 2.4.2
[   28.704000] IFX MEI Version 5.00.00
[   28.728000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[   28.752000] fuse init (API version 7.23)
[   28.796000] usbcore: registered new interface driver cdc_acm
[   28.800000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   28.812000] usbcore: registered new interface driver cdc_wdm
[   28.828000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   28.832000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   28.884000] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[   28.892000] request_timer(3, 0x000001AE, 1)...successful!
[   28.896000] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[   28.916000] ATM1.0.26    ATM (A1) firmware version 0.17
[   28.920000] ifxmips_atm: ATM init succeed
[   28.944000] nf_conntrack version 0.5.0 (942 buckets, 3768 max)
[   29.180000] PPP MPPE Compression module registered
[   29.188000] NET: Registered protocol family 24
[   29.196000] PPTP driver version 0.8.5
[   29.212000] usblp 1-1.1:1.0: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0273
[   29.220000] usbcore: registered new interface driver usblp
[   29.248000] usbcore: registered new interface driver usbserial
[   29.256000] usbcore: registered new interface driver usbserial_generic
[   29.260000] usbserial: USB Serial support registered for generic
[   29.344000] xt_time: kernel timezone is -0000
[   29.352000] usbcore: registered new interface driver cdc_ether
[   29.364000] usbcore: registered new interface driver cdc_ncm
[   29.488000] usbcore: registered new interface driver huawei_cdc_ncm
[   29.500000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   29.696000] usbcore: registered new interface driver qmi_wwan
[   29.704000] usbcore: registered new interface driver rndis_host
[   29.772000] usbcore: registered new interface driver sierra
[   29.776000] usbserial: USB Serial support registered for Sierra USB modem
[   29.792000] usbcore: registered new interface driver sierra_net
[   29.808000] usbcore: registered new interface driver cdc_mbim
[   29.820000] usbcore: registered new interface driver option
[   29.824000] usbserial: USB Serial support registered for GSM modem (1-port)
[   29.840000] usbcore: registered new interface driver qcserial
[   29.844000] usbserial: USB Serial support registered for Qualcomm USB modem
[   29.892000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[   29.896000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[   29.904000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT2860.eeprom'.
[   29.916000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2860, rev 0103 detected
[   29.924000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0001 detected
[   29.932000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   54.780000] device eth0.1 entered promiscuous mode
[   54.784000] device eth0 entered promiscuous mode
[   56.392000] br-lan: port 1(eth0.1) entered forwarding state
[   56.396000] br-lan: port 1(eth0.1) entered forwarding state
[   58.400000] br-lan: port 1(eth0.1) entered forwarding state
[   68.804000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[   69.260000] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
[   69.372000] device wlan0-1 entered promiscuous mode
[   79.316000] wlan0: authenticate with c8:3a:35:44:bd:f0
[   79.332000] wlan0: send auth to c8:3a:35:44:bd:f0 (try 1/3)
[   79.336000] wlan0: authenticated
[   79.352000] wlan0: associate with c8:3a:35:44:bd:f0 (try 1/3)
[   79.364000] wlan0: RX AssocResp from c8:3a:35:44:bd:f0 (capab=0x411 status=0 aid=1)
[   79.368000] wlan0: associated
[   83.456000] br-lan: port 2(wlan0-1) entered forwarding state
[   83.460000] br-lan: port 2(wlan0-1) entered forwarding state
[   85.464000] br-lan: port 2(wlan0-1) entered forwarding state
[ 1005.448000] device wlan0-1 left promiscuous mode
[ 1005.448000] br-lan: port 2(wlan0-1) entered disabled state
[ 1007.364000] wlan0: deauthenticating from c8:3a:35:44:bd:f0 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 1013.740000] device wlan0-1 entered promiscuous mode
[ 1019.092000] wlan0: authenticate with c8:3a:35:44:bd:f0
[ 1019.104000] wlan0: send auth to c8:3a:35:44:bd:f0 (try 1/3)
[ 1019.112000] wlan0: authenticated
[ 1019.120000] wlan0: associate with c8:3a:35:44:bd:f0 (try 1/3)
[ 1019.128000] wlan0: RX AssocResp from c8:3a:35:44:bd:f0 (capab=0x411 status=0 aid=1)
[ 1019.132000] wlan0: associated
[ 1022.284000] br-wan: port 1(wlan0-1) entered forwarding state
[ 1022.288000] br-wan: port 1(wlan0-1) entered forwarding state
[ 1024.292000] br-wan: port 1(wlan0-1) entered forwarding state
[ 2173.936000] eth0: tx ring full

9 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,013

Odp: Easy Box 802 OpenWRT - print server + repeater

Więc nie odblokowałeś firewalla na 192.168.1.101, na wanie. nasłuch na 192.168.1.101 to jeszcze nie wszystko.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

10 Odpowiedź przez BROWAReq

  • Zarejestrowany: 2018-07-12
  • Posty: 7

Odp: Easy Box 802 OpenWRT - print server + repeater

Poprzez :
Sieć -> zapora -> reguły ruchu sieciowego -> Otwarte porty na routerze - i tutaj wpisać nazwę np drukarka, Protokół TCP+UDP, port 9100  tak?
Czy poniżej NAT źródłowy:
Nazwa (drukarka) -> strefa źródłowa (wan lub lan) -> strefa docelowa (wan lub lan) -> do źródłowego IP (192.168.1.101 ?) -> do źródłowego portu (9100)?
Wybacz pewnie głupie pytania ale odnośnie połączeń sieciowych to dopiero zaczynam się uczyć smile

11 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,013

Odp: Easy Box 802 OpenWRT - print server + repeater

W ten sposób: http://eko.one.pl/?p=openwrt-konfigurac … estronywan

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona

12 Odpowiedź przez 9tysiecy

  • Zarejestrowany: 2018-01-30
  • Posty: 724

Odp: Easy Box 802 OpenWRT - print server + repeater

Czemu robisz sobie separacje sieci NATem i bawisz się w przekierowania zamiast ustawić EasyBox jako most bezprzewodowy? Nie łatwiej?

13 Odpowiedź przez BROWAReq (edytowany przez BROWAReq 2018-07-17 10:16:52)

  • Zarejestrowany: 2018-07-12
  • Posty: 7

Odp: Easy Box 802 OpenWRT - print server + repeater

Miałem nadzieję, że ogarnę to w gui ale widzę, że nie da rady.
Ściągnąłem już Putty i będę wieczorem dalej walczył z tym.
Jak dobrze rozumiem potrzebuję przekopiować te ustawienia z linku, w miejscu name=ssh  wpisać np name=drukarka a w miejscu
dest_port=22 podać port 9100 ?
Ewentualnie jak to nie zadziała to może faktycznie skorzystam z ustawień mostu - po prostu wcześniej nie umiałem w gui go ustawić smile

14 Odpowiedź przez Cezary

  • Skąd: Warszawa
  • Zarejestrowany: 2006-02-25
  • Posty: 116,013

Odp: Easy Box 802 OpenWRT - print server + repeater

Dokładnie tak.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

Cezary's Strona