#####################################################
#              Huawei E1752 (HSPA + modem)
#####################################################

DefaultVendor= 0x12d1
DefaultProduct=0x141b

TargetVendor= 0x12d1

TargetProductList="1001,1406,140b,140c,1412,141b,14ac"

# HuaweiMode=1

checkSuccess=20

MessageContent="55534243123456780000000000000011060000000000000000000000000000"

Warning: TargetProductList overrides TargetProduct!

Looking for target devices ...
 Found devices in target mode or class (1)
Looking for default devices ...
 Found devices in default mode or class (1)
Accessing device 003 on bus 001 ...
Using endpoints 0x01 (out) and 0x82 (in)
Using endpoints 0x01 (out) and 0x82 (in)
Not a storage device, skipping SCSI inquiry

USB description data (for identification)
-------------------------
Manufacturer: HUAWEI Technology
     Product: HUAWEI Mobile
  Serial No.: 1234567890ABCDEF
-------------------------
Looking for active driver ...
 OK, driver found ("usbserial_generic")
 OK, driver "usbserial_generic" detached
Setting up communication with interface 0 ...
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
 OK, message successfully sent
Resetting response endpoint 0x82
Resetting message endpoint 0x01
-> Run lsusb to note any changes. Bye.

Mar 12 11:29:58 Gargoyle user.info kernel: generic ttyUSB0: generic converter now disconnected from ttyUSB0
Mar 12 11:29:58 Gargoyle user.info kernel: usbserial_generic 1-1:1.0: device disconnected
Mar 12 11:29:58 Gargoyle user.info kernel: usb 1-1: USB disconnect, address 2
Mar 12 11:29:58 Gargoyle user.info kernel: generic ttyUSB1: generic converter now disconnected from ttyUSB1
Mar 12 11:29:58 Gargoyle user.info kernel: usbserial_generic 1-1:1.1: device disconnected
Mar 12 11:29:58 Gargoyle user.info kernel: generic ttyUSB2: generic converter now disconnected from ttyUSB2
Mar 12 11:29:58 Gargoyle user.info kernel: usbserial_generic 1-1:1.2: device disconnected
Mar 12 11:30:02 Gargoyle user.info kernel: usb 1-1: new high speed USB device using ar71xx-ehci and address 3
Mar 12 11:30:02 Gargoyle user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Mar 12 11:30:02 Gargoyle user.info kernel: usbserial_generic 1-1:1.0: GSM modem (1-port) converter detected
Mar 12 11:30:02 Gargoyle user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Mar 12 11:30:02 Gargoyle user.info kernel: usbserial_generic 1-1:1.1: GSM modem (1-port) converter detected
Mar 12 11:30:02 Gargoyle user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Mar 12 11:30:02 Gargoyle user.info kernel: usbserial_generic 1-1:1.2: generic converter detected
Mar 12 11:30:02 Gargoyle user.info kernel: usb 1-1: generic converter now attached to ttyUSB2
Mar 12 11:30:02 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=1234567890ABCDEF
Mar 12 11:30:03 Gargoyle user.notice usb-modeswitch: 1-1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=1234567890ABCDEF
Mar 12 11:30:03 Gargoyle user.notice usb-modeswitch: 1-1:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=1234567890ABCDEF
Mar 12 11:30:35 Gargoyle user.err kernel: option: option_instat_callback: error -143
Mar 12 11:30:35 Gargoyle user.info kernel: option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
Mar 12 11:30:35 Gargoyle user.info kernel: usbserial_generic 1-1:1.0: device disconnected
Mar 12 11:30:35 Gargoyle user.info kernel: usb 1-1: USB disconnect, address 3
Mar 12 11:30:35 Gargoyle user.info kernel: option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
Mar 12 11:30:35 Gargoyle user.info kernel: usbserial_generic 1-1:1.1: device disconnected
Mar 12 11:30:35 Gargoyle user.info kernel: generic ttyUSB2: generic converter now disconnected from ttyUSB2
Mar 12 11:30:35 Gargoyle user.info kernel: usbserial_generic 1-1:1.2: device disconnected
Mar 12 11:30:39 Gargoyle user.info kernel: usb 1-1: new high speed USB device using ar71xx-ehci and address 4
Mar 12 11:30:39 Gargoyle user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Mar 12 11:30:39 Gargoyle user.info kernel: usbserial_generic 1-1:1.0: GSM modem (1-port) converter detected
Mar 12 11:30:39 Gargoyle user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
Mar 12 11:30:39 Gargoyle user.info kernel: usbserial_generic 1-1:1.1: GSM modem (1-port) converter detected
Mar 12 11:30:39 Gargoyle user.info kernel: usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
Mar 12 11:30:39 Gargoyle user.info kernel: usbserial_generic 1-1:1.2: generic converter detected
Mar 12 11:30:39 Gargoyle user.info kernel: usb 1-1: generic converter now attached to ttyUSB2
Mar 12 11:30:39 Gargoyle user.notice usb-modeswitch: 1-1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=1234567890ABCDEF
Mar 12 11:30:40 Gargoyle user.notice usb-modeswitch: 1-1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=1234567890ABCDEF
Mar 12 11:30:40 Gargoyle user.notice usb-modeswitch: 1-1:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=1234567890ABCDEF
Mar 12 11:31:01 Gargoyle cron.err crond[2058]: USER root pid 10267 cmd /usr/bin/set_kernel_timezone >/dev/null 2>&1

On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 802daa50, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=TL-WR1043ND
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29288k/32768k available (2123k kernel code, 3480k reserved, 418k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR1043ND
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
yaffs Feb 28 2011 19:00:24 Installing.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: s25sl064a (8192 Kbytes)
spi0.0: searching for MyLoader partition table at offset 0x10000
spi0.0: searching for MyLoader partition table at offset 0x20000
spi0.0: searching for MyLoader partition table at offset 0x30000
spi0.0: searching for MyLoader partition table at offset 0x40000
spi0.0: no MyLoader partition table found
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=550000, len=2A0000
0x000000550000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
Realtek RTL8366RB ethernet switch driver version 0.2.3
rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
rtl8366rb: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
eth0: using fixed link parameters
Atheros AR71xx hardware watchdog driver version 0.1.0
ar71xx-wdt: timeout=15 secs (max=21)
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 152k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
ar71xx: pll_reg 0xb8050014: 0x1a000000
eth0: link up (1000Mbps/Full duplex)
Registered led device: tl-wr1043nd:green:usb
Registered led device: tl-wr1043nd:green:system
Registered led device: tl-wr1043nd:green:qss
Registered led device: tl-wr1043nd:green:wlan
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
eth0: link down
ar71xx: pll_reg 0xb8050014: 0x1a000000
eth0: link up (1000Mbps/Full duplex)
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-01-31-4-g86702b3
Backport based on wireless-testing.git master-2011-02-07
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
ath: EEPROM regdomain: 0x0
ath: EEPROM indicates default country code should be used
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x3a
ath: Country alpha2 being used: US
ath: Regpair used: 0x3a
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
cfg80211: Calling CRDA for country: US
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PPP generic driver version 2.4.2
cfg80211: Regulatory domain changed to country: US
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (460 buckets, 1840 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
usb 1-1: new high speed USB device using ar71xx-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
xt_time: kernel timezone is -0000
        Hooked IMQ after mangle on PREROUTING
        Hooked IMQ after nat on POSTROUTING
IMQ driver loaded successfully.
Ebtables v2.0 registered
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbserial_generic 1-1:1.0: generic converter detected
usb 1-1: generic converter now attached to ttyUSB0
usbserial_generic 1-1:1.1: generic converter detected
usb 1-1: generic converter now attached to ttyUSB1
usbserial_generic 1-1:1.2: generic converter detected
usb 1-1: generic converter now attached to ttyUSB2
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
fuse init (API version 7.13)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
ar71xx-wdt: enabling watchdog timer
generic ttyUSB0: generic converter now disconnected from ttyUSB0
usbserial_generic 1-1:1.0: device disconnected
usb 1-1: USB disconnect, address 2
generic ttyUSB1: generic converter now disconnected from ttyUSB1
usbserial_generic 1-1:1.1: device disconnected
generic ttyUSB2: generic converter now disconnected from ttyUSB2
usbserial_generic 1-1:1.2: device disconnected
usb 1-1: new high speed USB device using ar71xx-ehci and address 3
usb 1-1: configuration #1 chosen from 1 choice
usbserial_generic 1-1:1.0: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
usbserial_generic 1-1:1.1: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usbserial_generic 1-1:1.2: generic converter detected
usb 1-1: generic converter now attached to ttyUSB2
option: option_instat_callback: error -143
option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
usbserial_generic 1-1:1.0: device disconnected
usb 1-1: USB disconnect, address 3
option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
usbserial_generic 1-1:1.1: device disconnected
generic ttyUSB2: generic converter now disconnected from ttyUSB2
usbserial_generic 1-1:1.2: device disconnected
usb 1-1: new high speed USB device using ar71xx-ehci and address 4
usb 1-1: configuration #1 chosen from 1 choice
usbserial_generic 1-1:1.0: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
usbserial_generic 1-1:1.1: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usbserial_generic 1-1:1.2: generic converter detected
usb 1-1: generic converter now attached to ttyUSB2