Temat: EasyBox 802 LEDE usb overcurrent
Witam mam pytanie czy istnieje patch na problem z usb overcurent blad ten wystepuje nawet bez podlaczonych urzadzen a nawet jesli sie podlaczy to nie wykrywa oto log.
[ 0.000000] Linux version 4.4.50 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Mon Feb 20 17:13:44 2017
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ARV752DPW - Arcor 802
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8046e4b0, node_mem_map 81007880
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00040008
[ 0.000000] Readback ErrCtl register=00040008
[ 0.000000] Memory: 58792K/65536K available (3875K kernel code, 156K rwdata, 620K rodata, 1220K init, 200K bss, 6744K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[ 0.000018] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[ 0.007957] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.050570] pid_max: default: 32768 minimum: 301
[ 0.055535] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.062089] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.079120] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.088902] pinctrl core: initialized pinctrl subsystem
[ 0.096371] NET: Registered protocol family 16
[ 0.109089] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.115639] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.192931] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.198627] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.203897] IO 0x000000001ae00000..0x000000001affffff
[ 0.238005] usbcore: registered new interface driver usbfs
[ 0.243635] usbcore: registered new interface driver hub
[ 0.249098] usbcore: registered new device driver usb
[ 0.254738] PCI host bridge to bus 0000:00
[ 0.258794] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.265723] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.272668] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.279517] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.287623] pci 0000:00:0e.0: [1814:0601] type 00 class 0x028000
[ 0.287720] pci 0000:00:0e.0: reg 0x10: [mem 0xffff0000-0xffffffff]
[ 0.287882] pci 0000:00:0e.0: PME# supported from D0 D3hot D3cold
[ 0.288367] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.288445] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.296628] clocksource: Switched to clocksource MIPS
[ 0.304152] NET: Registered protocol family 2
[ 0.310309] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.317283] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.323673] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.330253] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.336076] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.342801] NET: Registered protocol family 1
[ 0.347213] PCI: CLS 0 bytes, default 32
[ 0.360759] gptu: totally 6 16-bit timers/counters
[ 0.365705] gptu: misc_register on minor 63
[ 0.369842] gptu: succeeded to request irq 126
[ 0.374345] gptu: succeeded to request irq 127
[ 0.378859] gptu: succeeded to request irq 128
[ 0.383373] gptu: succeeded to request irq 129
[ 0.387887] gptu: succeeded to request irq 130
[ 0.392400] gptu: succeeded to request irq 131
[ 0.403631] lantiq,vmmc 1f103000.vmmc: requested GPIO 465
[ 0.408990] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03a00000
[ 0.416845] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.422975] Crashlog allocated RAM at address 0x3f00000
[ 0.467023] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.472797] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.489681] io scheduler noop registered
[ 0.493539] io scheduler deadline registered (default)
[ 0.499840] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 0.508804] console [ttyLTQ0] enabled
[ 0.515908] bootconsole [early0] disabled
[ 0.525323] lantiq nor flash device: 00800000 at 10000000
[ 0.529601] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[ 0.538560] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.543562] Amd/Fujitsu Extended Query version 1.1.
[ 0.548423] number of CFI chips: 1
[ 0.551771] 4 ofpart partitions found on MTD device ltq_nor
[ 0.557128] Creating 4 MTD partitions on "ltq_nor":
[ 0.561863] 0x000000000000-0x000000010000 : "uboot"
[ 0.573392] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.580977] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.629779] 2 uimage-fw partitions found on MTD device firmware
[ 0.634225] 0x000000020000-0x00000019cb36 : "kernel"
[ 0.642076] 0x00000019cb36-0x0000007f0000 : "rootfs"
[ 0.649440] mtd: device 4 (rootfs) set to be root filesystem
[ 0.653752] 1 squashfs-split partitions found on MTD device rootfs
[ 0.659636] 0x000000490000-0x0000007f0000 : "rootfs_data"
[ 0.668605] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.699512] libphy: ltq_mii: probed
[ 0.794784] Registering RTL8306SDM switch with Chip ID: 0x5988, version: 0x0000
[ 0.800597] eth0: attached PHY [Realtek RTL8306S] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.810448] wdt 1f8803f0.watchdog: Init done
[ 0.820038] NET: Registered protocol family 10
[ 0.836850] NET: Registered protocol family 17
[ 0.839908] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.852100] 8021q: 802.1Q VLAN Support v1.8
[ 0.880109] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.893446] Freeing unused kernel memory: 1220K (8048f000 - 805c0000)
[ 3.340879] init: Console is alive
[ 3.343294] init: - watchdog -
[ 6.141940] dwc2 1e101000.ifxhcd: requested GPIO 464
[ 7.001014] dwc2 1e101000.ifxhcd: DWC OTG Controller
[ 7.004542] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[ 7.011707] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[ 7.019291] hub 1-0:1.0: USB hub found
[ 7.022405] hub 1-0:1.0: 1 port detected
[ 7.037997] init: - preinit -
[ 7.179118] dwc2 1e101000.ifxhcd: Overcurrent change detected
[ 7.749697] dwc2 1e101000.ifxhcd: Overcurrent change detected
[ 8.133355] random: procd: uninitialized urandom read (4 bytes read, 33 bits of entropy available)
[ 11.727160] jffs2: notice: (372) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 11.780154] mount_root: loading kmods from internal overlay
[ 12.051629] kmodloader: failed to open /tmp/overlay/upper/lib/modules/4.4.50/ledtrig-usbport.ko
[ 12.915168] SCSI subsystem initialized
[ 13.016960] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.023742] ohci-platform: OHCI generic platform driver
[ 13.860956] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 13.872570] block: extroot: not configured
[ 13.877013] mount_root: switching to jffs2 overlay
[ 13.895560] urandom-seed: Seeding with /etc/urandom.seed
[ 13.984952] procd: - early -
[ 13.986616] procd: - watchdog -
[ 14.748924] procd: - ubus -
[ 15.234977] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.386736] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.398251] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.405859] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.415371] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.423195] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.434878] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.442966] random: ubusd: uninitialized urandom read (4 bytes read, 62 bits of entropy available)
[ 15.452101] procd: - init -
[ 16.080718] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 16.100500] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
[ 16.120445] NET: Registered protocol family 8
[ 16.123391] NET: Registered protocol family 20
[ 16.138103] PPP generic driver version 2.4.2
[ 16.155180] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.175829] IFX MEI Version 5.00.00
[ 16.193335] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[ 16.215053] Loading modules backported from Linux version wt-2016-10-03-1-g6fcb1a6
[ 16.221122] Backport generated by backports.git backports-20160324-9-g0e38f5c
[ 16.245649] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
[ 16.252844] request_timer(3, 0x000001AE, 1)...successful!
[ 16.258259] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
[ 16.271391] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.287386] ATM1.0.26 ATM (A1) firmware version 0.17
[ 16.291156] ifxmips_atm: ATM init succeed
[ 16.327640] nf_conntrack version 0.5.0 (937 buckets, 3748 max)
[ 16.399081] NET: Registered protocol family 24
[ 16.409219] random: ubusd: uninitialized urandom read (4 bytes read, 67 bits of entropy available)
[ 16.464008] xt_time: kernel timezone is -0000
[ 16.664528] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 16.670025] rt2800pci 0000:00:0e.0: loaded eeprom from mtd device "board_config"
[ 16.675950] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2860, rev 0103 detected
[ 16.683523] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0001 detected
[ 16.691332] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 31.628757] random: nonblocking pool is initialized
[ 33.645039] rt2x00mmio_regbusy_read() Indirect register access failed: offset=0x00007010, value=0x499e6ce6
[ 35.801809] device eth0 entered promiscuous mode
[ 35.812933] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 36.847206] IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready
[ 36.988911] br-lan: port 1(eth0) entered forwarding state
[ 36.992962] br-lan: port 1(eth0) entered forwarding state
[ 36.998349] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 38.996698] br-lan: port 1(eth0) entered forwarding state
[ 41.959991] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 42.099885] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.40
[ 42.235234] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 42.250230] device wlan0 entered promiscuous mode
[ 46.801162] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 46.806396] br-lan: port 2(wlan0) entered forwarding state
[ 46.811456] br-lan: port 2(wlan0) entered forwarding state
[ 48.812675] br-lan: port 2(wlan0) entered forwarding state
lsusb -v
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.04
iManufacturer 3 Linux 4.4.50 dwc2_hsotg
iProduct 2 DWC OTG Controller
iSerial 1 1e101000.ifxhcd
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 1
wHubCharacteristic 0x0008
Ganged power switching
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0000
Device Status: 0x0001
Self Powered
